| /* |
| * sound/oss/sscape.c |
| * |
| * Low level driver for Ensoniq SoundScape |
| * |
| * |
| * Copyright (C) by Hannu Savolainen 1993-1997 |
| * |
| * OSS/Free for Linux is distributed under the GNU GENERAL PUBLIC LICENSE (GPL) |
| * Version 2 (June 1991). See the "COPYING" file distributed with this software |
| * for more info. |
| * |
| * |
| * Thomas Sailer : ioctl code reworked (vmalloc/vfree removed) |
| * Sergey Smitienko : ensoniq p'n'p support |
| * Christoph Hellwig : adapted to module_init/module_exit |
| * Bartlomiej Zolnierkiewicz : added __init to attach_sscape() |
| * Chris Rankin : Specify that this module owns the coprocessor |
| * Arnaldo C. de Melo : added missing restore_flags in sscape_pnp_upload_file |
| */ |
| |
| #include <linux/init.h> |
| #include <linux/module.h> |
| |
| #include "sound_config.h" |
| #include "sound_firmware.h" |
| |
| #include <linux/types.h> |
| #include <linux/errno.h> |
| #include <linux/signal.h> |
| #include <linux/fcntl.h> |
| #include <linux/ctype.h> |
| #include <linux/stddef.h> |
| #include <linux/kmod.h> |
| #include <asm/dma.h> |
| #include <asm/io.h> |
| #include <linux/wait.h> |
| #include <linux/slab.h> |
| #include <linux/ioport.h> |
| #include <linux/delay.h> |
| #include <linux/proc_fs.h> |
| #include <linux/mm.h> |
| #include <linux/spinlock.h> |
| |
| #include "coproc.h" |
| |
| #include "ad1848.h" |
| #include "mpu401.h" |
| |
| /* |
| * I/O ports |
| */ |
| #define MIDI_DATA 0 |
| #define MIDI_CTRL 1 |
| #define HOST_CTRL 2 |
| #define TX_READY 0x02 |
| #define RX_READY 0x01 |
| #define HOST_DATA 3 |
| #define ODIE_ADDR 4 |
| #define ODIE_DATA 5 |
| |
| /* |
| * Indirect registers |
| */ |
| |
| #define GA_INTSTAT_REG 0 |
| #define GA_INTENA_REG 1 |
| #define GA_DMAA_REG 2 |
| #define GA_DMAB_REG 3 |
| #define GA_INTCFG_REG 4 |
| #define GA_DMACFG_REG 5 |
| #define GA_CDCFG_REG 6 |
| #define GA_SMCFGA_REG 7 |
| #define GA_SMCFGB_REG 8 |
| #define GA_HMCTL_REG 9 |
| |
| /* |
| * DMA channel identifiers (A and B) |
| */ |
| |
| #define SSCAPE_DMA_A 0 |
| #define SSCAPE_DMA_B 1 |
| |
| #define PORT(name) (devc->base+name) |
| |
| /* |
| * Host commands recognized by the OBP microcode |
| */ |
| |
| #define CMD_GEN_HOST_ACK 0x80 |
| #define CMD_GEN_MPU_ACK 0x81 |
| #define CMD_GET_BOARD_TYPE 0x82 |
| #define CMD_SET_CONTROL 0x88 /* Old firmware only */ |
| #define CMD_GET_CONTROL 0x89 /* Old firmware only */ |
| #define CTL_MASTER_VOL 0 |
| #define CTL_MIC_MODE 2 |
| #define CTL_SYNTH_VOL 4 |
| #define CTL_WAVE_VOL 7 |
| #define CMD_SET_EXTMIDI 0x8a |
| #define CMD_GET_EXTMIDI 0x8b |
| #define CMD_SET_MT32 0x8c |
| #define CMD_GET_MT32 0x8d |
| |
| #define CMD_ACK 0x80 |
| |
| #define IC_ODIE 1 |
| #define IC_OPUS 2 |
| |
| typedef struct sscape_info |
| { |
| int base, irq, dma; |
| |
| int codec, codec_irq; /* required to setup pnp cards*/ |
| int codec_type; |
| int ic_type; |
| char* raw_buf; |
| unsigned long raw_buf_phys; |
| int buffsize; /* -------------------------- */ |
| spinlock_t lock; |
| int ok; /* Properly detected */ |
| int failed; |
| int dma_allocated; |
| int codec_audiodev; |
| int opened; |
| int *osp; |
| int my_audiodev; |
| } sscape_info; |
| |
| static struct sscape_info adev_info = { |
| 0 |
| }; |
| |
| static struct sscape_info *devc = &adev_info; |
| static int sscape_mididev = -1; |
| |
| /* Some older cards have assigned interrupt bits differently than new ones */ |
| static char valid_interrupts_old[] = { |
| 9, 7, 5, 15 |
| }; |
| |
| static char valid_interrupts_new[] = { |
| 9, 5, 7, 10 |
| }; |
| |
| static char *valid_interrupts = valid_interrupts_new; |
| |
| /* |
| * See the bottom of the driver. This can be set by spea =0/1. |
| */ |
| |
| #ifdef REVEAL_SPEA |
| static char old_hardware = 1; |
| #else |
| static char old_hardware; |
| #endif |
| |
| static void sleep(unsigned howlong) |
| { |
| current->state = TASK_INTERRUPTIBLE; |
| schedule_timeout(howlong); |
| } |
| |
| static unsigned char sscape_read(struct sscape_info *devc, int reg) |
| { |
| unsigned long flags; |
| unsigned char val; |
| |
| spin_lock_irqsave(&devc->lock,flags); |
| outb(reg, PORT(ODIE_ADDR)); |
| val = inb(PORT(ODIE_DATA)); |
| spin_unlock_irqrestore(&devc->lock,flags); |
| return val; |
| } |
| |
| static void __sscape_write(int reg, int data) |
| { |
| outb(reg, PORT(ODIE_ADDR)); |
| outb(data, PORT(ODIE_DATA)); |
| } |
| |
| static void sscape_write(struct sscape_info *devc, int reg, int data) |
| { |
| unsigned long flags; |
| |
| spin_lock_irqsave(&devc->lock,flags); |
| __sscape_write(reg, data); |
| spin_unlock_irqrestore(&devc->lock,flags); |
| } |
| |
| static unsigned char sscape_pnp_read_codec(sscape_info* devc, unsigned char reg) |
| { |
| unsigned char res; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&devc->lock,flags); |
| outb( reg, devc -> codec); |
| res = inb (devc -> codec + 1); |
| spin_unlock_irqrestore(&devc->lock,flags); |
| return res; |
| |
| } |
| |
| static void sscape_pnp_write_codec(sscape_info* devc, unsigned char reg, unsigned char data) |
| { |
| unsigned long flags; |
| |
| spin_lock_irqsave(&devc->lock,flags); |
| outb( reg, devc -> codec); |
| outb( data, devc -> codec + 1); |
| spin_unlock_irqrestore(&devc->lock,flags); |
| } |
| |
| static void host_open(struct sscape_info *devc) |
| { |
| outb((0x00), PORT(HOST_CTRL)); /* Put the board to the host mode */ |
| } |
| |
| static void host_close(struct sscape_info *devc) |
| { |
| outb((0x03), PORT(HOST_CTRL)); /* Put the board to the MIDI mode */ |
| } |
| |
| static int host_write(struct sscape_info *devc, unsigned char *data, int count) |
| { |
| unsigned long flags; |
| int i, timeout_val; |
| |
| spin_lock_irqsave(&devc->lock,flags); |
| /* |
| * Send the command and data bytes |
| */ |
| |
| for (i = 0; i < count; i++) |
| { |
| for (timeout_val = 10000; timeout_val > 0; timeout_val--) |
| if (inb(PORT(HOST_CTRL)) & TX_READY) |
| break; |
| |
| if (timeout_val <= 0) |
| { |
| spin_unlock_irqrestore(&devc->lock,flags); |
| return 0; |
| } |
| outb(data[i], PORT(HOST_DATA)); |
| } |
| spin_unlock_irqrestore(&devc->lock,flags); |
| return 1; |
| } |
| |
| static int host_read(struct sscape_info *devc) |
| { |
| unsigned long flags; |
| int timeout_val; |
| unsigned char data; |
| |
| spin_lock_irqsave(&devc->lock,flags); |
| /* |
| * Read a byte |
| */ |
| |
| for (timeout_val = 10000; timeout_val > 0; timeout_val--) |
| if (inb(PORT(HOST_CTRL)) & RX_READY) |
| break; |
| |
| if (timeout_val <= 0) |
| { |
| spin_unlock_irqrestore(&devc->lock,flags); |
| return -1; |
| } |
| data = inb(PORT(HOST_DATA)); |
| spin_unlock_irqrestore(&devc->lock,flags); |
| return data; |
| } |
| |
| #if 0 /* unused */ |
| static int host_command1(struct sscape_info *devc, int cmd) |
| { |
| unsigned char buf[10]; |
| buf[0] = (unsigned char) (cmd & 0xff); |
| return host_write(devc, buf, 1); |
| } |
| #endif /* unused */ |
| |
| |
| static int host_command2(struct sscape_info *devc, int cmd, int parm1) |
| { |
| unsigned char buf[10]; |
| |
| buf[0] = (unsigned char) (cmd & 0xff); |
| buf[1] = (unsigned char) (parm1 & 0xff); |
| |
| return host_write(devc, buf, 2); |
| } |
| |
| static int host_command3(struct sscape_info *devc, int cmd, int parm1, int parm2) |
| { |
| unsigned char buf[10]; |
| |
| buf[0] = (unsigned char) (cmd & 0xff); |
| buf[1] = (unsigned char) (parm1 & 0xff); |
| buf[2] = (unsigned char) (parm2 & 0xff); |
| return host_write(devc, buf, 3); |
| } |
| |
| static void set_mt32(struct sscape_info *devc, int value) |
| { |
| host_open(devc); |
| host_command2(devc, CMD_SET_MT32, value ? 1 : 0); |
| if (host_read(devc) != CMD_ACK) |
| { |
| /* printk( "SNDSCAPE: Setting MT32 mode failed\n"); */ |
| } |
| host_close(devc); |
| } |
| |
| static void set_control(struct sscape_info *devc, int ctrl, int value) |
| { |
| host_open(devc); |
| host_command3(devc, CMD_SET_CONTROL, ctrl, value); |
| if (host_read(devc) != CMD_ACK) |
| { |
| /* printk( "SNDSCAPE: Setting control (%d) failed\n", ctrl); */ |
| } |
| host_close(devc); |
| } |
| |
| static void do_dma(struct sscape_info *devc, int dma_chan, unsigned long buf, int blk_size, int mode) |
| { |
| unsigned char temp; |
| |
| if (dma_chan != SSCAPE_DMA_A) |
| { |
| printk(KERN_WARNING "soundscape: Tried to use DMA channel != A. Why?\n"); |
| return; |
| } |
| audio_devs[devc->codec_audiodev]->flags &= ~DMA_AUTOMODE; |
| DMAbuf_start_dma(devc->codec_audiodev, buf, blk_size, mode); |
| audio_devs[devc->codec_audiodev]->flags |= DMA_AUTOMODE; |
| |
| temp = devc->dma << 4; /* Setup DMA channel select bits */ |
| if (devc->dma <= 3) |
| temp |= 0x80; /* 8 bit DMA channel */ |
| |
| temp |= 1; /* Trigger DMA */ |
| sscape_write(devc, GA_DMAA_REG, temp); |
| temp &= 0xfe; /* Clear DMA trigger */ |
| sscape_write(devc, GA_DMAA_REG, temp); |
| } |
| |
| static int verify_mpu(struct sscape_info *devc) |
| { |
| /* |
| * The SoundScape board could be in three modes (MPU, 8250 and host). |
| * If the card is not in the MPU mode, enabling the MPU driver will |
| * cause infinite loop (the driver believes that there is always some |
| * received data in the buffer. |
| * |
| * Detect this by looking if there are more than 10 received MIDI bytes |
| * (0x00) in the buffer. |
| */ |
| |
| int i; |
| |
| for (i = 0; i < 10; i++) |
| { |
| if (inb(devc->base + HOST_CTRL) & 0x80) |
| return 1; |
| |
| if (inb(devc->base) != 0x00) |
| return 1; |
| } |
| printk(KERN_WARNING "SoundScape: The device is not in the MPU-401 mode\n"); |
| return 0; |
| } |
| |
| static int sscape_coproc_open(void *dev_info, int sub_device) |
| { |
| if (sub_device == COPR_MIDI) |
| { |
| set_mt32(devc, 0); |
| if (!verify_mpu(devc)) |
| return -EIO; |
| } |
| return 0; |
| } |
| |
| static void sscape_coproc_close(void *dev_info, int sub_device) |
| { |
| struct sscape_info *devc = dev_info; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&devc->lock,flags); |
| if (devc->dma_allocated) |
| { |
| __sscape_write(GA_DMAA_REG, 0x20); /* DMA channel disabled */ |
| devc->dma_allocated = 0; |
| } |
| spin_unlock_irqrestore(&devc->lock,flags); |
| return; |
| } |
| |
| static void sscape_coproc_reset(void *dev_info) |
| { |
| } |
| |
| static int sscape_download_boot(struct sscape_info *devc, unsigned char *block, int size, int flag) |
| { |
| unsigned long flags; |
| unsigned char temp; |
| volatile int done, timeout_val; |
| static unsigned char codec_dma_bits; |
| |
| if (flag & CPF_FIRST) |
| { |
| /* |
| * First block. Have to allocate DMA and to reset the board |
| * before continuing. |
| */ |
| |
| spin_lock_irqsave(&devc->lock,flags); |
| codec_dma_bits = sscape_read(devc, GA_CDCFG_REG); |
| |
| if (devc->dma_allocated == 0) |
| devc->dma_allocated = 1; |
| |
| spin_unlock_irqrestore(&devc->lock,flags); |
| |
| sscape_write(devc, GA_HMCTL_REG, |
| (temp = sscape_read(devc, GA_HMCTL_REG)) & 0x3f); /*Reset */ |
| |
| for (timeout_val = 10000; timeout_val > 0; timeout_val--) |
| sscape_read(devc, GA_HMCTL_REG); /* Delay */ |
| |
| /* Take board out of reset */ |
| sscape_write(devc, GA_HMCTL_REG, |
| (temp = sscape_read(devc, GA_HMCTL_REG)) | 0x80); |
| } |
| /* |
| * Transfer one code block using DMA |
| */ |
| if (audio_devs[devc->codec_audiodev]->dmap_out->raw_buf == NULL) |
| { |
| printk(KERN_WARNING "soundscape: DMA buffer not available\n"); |
| return 0; |
| } |
| memcpy(audio_devs[devc->codec_audiodev]->dmap_out->raw_buf, block, size); |
| |
| spin_lock_irqsave(&devc->lock,flags); |
| |
| /******** INTERRUPTS DISABLED NOW ********/ |
| |
| do_dma(devc, SSCAPE_DMA_A, |
| audio_devs[devc->codec_audiodev]->dmap_out->raw_buf_phys, |
| size, DMA_MODE_WRITE); |
| |
| /* |
| * Wait until transfer completes. |
| */ |
| |
| done = 0; |
| timeout_val = 30; |
| while (!done && timeout_val-- > 0) |
| { |
| int resid; |
| |
| if (HZ / 50) |
| sleep(HZ / 50); |
| clear_dma_ff(devc->dma); |
| if ((resid = get_dma_residue(devc->dma)) == 0) |
| done = 1; |
| } |
| |
| spin_unlock_irqrestore(&devc->lock,flags); |
| if (!done) |
| return 0; |
| |
| if (flag & CPF_LAST) |
| { |
| /* |
| * Take the board out of reset |
| */ |
| outb((0x00), PORT(HOST_CTRL)); |
| outb((0x00), PORT(MIDI_CTRL)); |
| |
| temp = sscape_read(devc, GA_HMCTL_REG); |
| temp |= 0x40; |
| sscape_write(devc, GA_HMCTL_REG, temp); /* Kickstart the board */ |
| |
| /* |
| * Wait until the ODB wakes up |
| */ |
| spin_lock_irqsave(&devc->lock,flags); |
| done = 0; |
| timeout_val = 5 * HZ; |
| while (!done && timeout_val-- > 0) |
| { |
| unsigned char x; |
| |
| sleep(1); |
| x = inb(PORT(HOST_DATA)); |
| if (x == 0xff || x == 0xfe) /* OBP startup acknowledge */ |
| { |
| DDB(printk("Soundscape: Acknowledge = %x\n", x)); |
| done = 1; |
| } |
| } |
| sscape_write(devc, GA_CDCFG_REG, codec_dma_bits); |
| |
| spin_unlock_irqrestore(&devc->lock,flags); |
| if (!done) |
| { |
| printk(KERN_ERR "soundscape: The OBP didn't respond after code download\n"); |
| return 0; |
| } |
| spin_lock_irqsave(&devc->lock,flags); |
| done = 0; |
| timeout_val = 5 * HZ; |
| while (!done && timeout_val-- > 0) |
| { |
| sleep(1); |
| if (inb(PORT(HOST_DATA)) == 0xfe) /* Host startup acknowledge */ |
| done = 1; |
| } |
| spin_unlock_irqrestore(&devc->lock,flags); |
| if (!done) |
| { |
| printk(KERN_ERR "soundscape: OBP Initialization failed.\n"); |
| return 0; |
| } |
| printk(KERN_INFO "SoundScape board initialized OK\n"); |
| set_control(devc, CTL_MASTER_VOL, 100); |
| set_control(devc, CTL_SYNTH_VOL, 100); |
| |
| #ifdef SSCAPE_DEBUG3 |
| /* |
| * Temporary debugging aid. Print contents of the registers after |
| * downloading the code. |
| */ |
| { |
| int i; |
| |
| for (i = 0; i < 13; i++) |
| printk("I%d = %02x (new value)\n", i, sscape_read(devc, i)); |
| } |
| #endif |
| |
| } |
| return 1; |
| } |
| |
| static int download_boot_block(void *dev_info, copr_buffer * buf) |
| { |
| if (buf->len <= 0 || buf->len > sizeof(buf->data)) |
| return -EINVAL; |
| |
| if (!sscape_download_boot(devc, buf->data, buf->len, buf->flags)) |
| { |
| printk(KERN_ERR "soundscape: Unable to load microcode block to the OBP.\n"); |
| return -EIO; |
| } |
| return 0; |
| } |
| |
| static int sscape_coproc_ioctl(void *dev_info, unsigned int cmd, void __user *arg, int local) |
| { |
| copr_buffer *buf; |
| int err; |
| |
| switch (cmd) |
| { |
| case SNDCTL_COPR_RESET: |
| sscape_coproc_reset(dev_info); |
| return 0; |
| |
| case SNDCTL_COPR_LOAD: |
| buf = (copr_buffer *) vmalloc(sizeof(copr_buffer)); |
| if (buf == NULL) |
| return -ENOSPC; |
| if (copy_from_user(buf, arg, sizeof(copr_buffer))) |
| { |
| vfree(buf); |
| return -EFAULT; |
| } |
| err = download_boot_block(dev_info, buf); |
| vfree(buf); |
| return err; |
| |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static coproc_operations sscape_coproc_operations = |
| { |
| "SoundScape M68K", |
| THIS_MODULE, |
| sscape_coproc_open, |
| sscape_coproc_close, |
| sscape_coproc_ioctl, |
| sscape_coproc_reset, |
| &adev_info |
| }; |
| |
| static struct resource *sscape_ports; |
| static int sscape_is_pnp; |
| |
| static void __init attach_sscape(struct address_info *hw_config) |
| { |
| #ifndef SSCAPE_REGS |
| /* |
| * Config register values for Spea/V7 Media FX and Ensoniq S-2000. |
| * These values are card |
| * dependent. If you have another SoundScape based card, you have to |
| * find the correct values. Do the following: |
| * - Compile this driver with SSCAPE_DEBUG1 defined. |
| * - Shut down and power off your machine. |
| * - Boot with DOS so that the SSINIT.EXE program is run. |
| * - Warm boot to {Linux|SYSV|BSD} and write down the lines displayed |
| * when detecting the SoundScape. |
| * - Modify the following list to use the values printed during boot. |
| * Undefine the SSCAPE_DEBUG1 |
| */ |
| #define SSCAPE_REGS { \ |
| /* I0 */ 0x00, \ |
| /* I1 */ 0xf0, /* Note! Ignored. Set always to 0xf0 */ \ |
| /* I2 */ 0x20, /* Note! Ignored. Set always to 0x20 */ \ |
| /* I3 */ 0x20, /* Note! Ignored. Set always to 0x20 */ \ |
| /* I4 */ 0xf5, /* Ignored */ \ |
| /* I5 */ 0x10, \ |
| /* I6 */ 0x00, \ |
| /* I7 */ 0x2e, /* I7 MEM config A. Likely to vary between models */ \ |
| /* I8 */ 0x00, /* I8 MEM config B. Likely to vary between models */ \ |
| /* I9 */ 0x40 /* Ignored */ \ |
| } |
| #endif |
| |
| unsigned long flags; |
| static unsigned char regs[10] = SSCAPE_REGS; |
| |
| int i, irq_bits = 0xff; |
| |
| if (old_hardware) |
| { |
| valid_interrupts = valid_interrupts_old; |
| conf_printf("Ensoniq SoundScape (old)", hw_config); |
| } |
| else |
| conf_printf("Ensoniq SoundScape", hw_config); |
| |
| for (i = 0; i < 4; i++) |
| { |
| if (hw_config->irq == valid_interrupts[i]) |
| { |
| irq_bits = i; |
| break; |
| } |
| } |
| if (hw_config->irq > 15 || (regs[4] = irq_bits == 0xff)) |
| { |
| printk(KERN_ERR "Invalid IRQ%d\n", hw_config->irq); |
| release_region(devc->base, 2); |
| release_region(devc->base + 2, 6); |
| if (sscape_is_pnp) |
| release_region(devc->codec, 2); |
| return; |
| } |
| |
| if (!sscape_is_pnp) { |
| |
| spin_lock_irqsave(&devc->lock,flags); |
| /* Host interrupt enable */ |
| sscape_write(devc, 1, 0xf0); /* All interrupts enabled */ |
| /* DMA A status/trigger register */ |
| sscape_write(devc, 2, 0x20); /* DMA channel disabled */ |
| /* DMA B status/trigger register */ |
| sscape_write(devc, 3, 0x20); /* DMA channel disabled */ |
| /* Host interrupt config reg */ |
| sscape_write(devc, 4, 0xf0 | (irq_bits << 2) | irq_bits); |
| /* Don't destroy CD-ROM DMA config bits (0xc0) */ |
| sscape_write(devc, 5, (regs[5] & 0x3f) | (sscape_read(devc, 5) & 0xc0)); |
| /* CD-ROM config (WSS codec actually) */ |
| sscape_write(devc, 6, regs[6]); |
| sscape_write(devc, 7, regs[7]); |
| sscape_write(devc, 8, regs[8]); |
| /* Master control reg. Don't modify CR-ROM bits. Disable SB emul */ |
| sscape_write(devc, 9, (sscape_read(devc, 9) & 0xf0) | 0x08); |
| spin_unlock_irqrestore(&devc->lock,flags); |
| } |
| #ifdef SSCAPE_DEBUG2 |
| /* |
| * Temporary debugging aid. Print contents of the registers after |
| * changing them. |
| */ |
| { |
| int i; |
| |
| for (i = 0; i < 13; i++) |
| printk("I%d = %02x (new value)\n", i, sscape_read(devc, i)); |
| } |
| #endif |
| |
| if (probe_mpu401(hw_config, sscape_ports)) |
| hw_config->always_detect = 1; |
| hw_config->name = "SoundScape"; |
| |
| hw_config->irq *= -1; /* Negative value signals IRQ sharing */ |
| attach_mpu401(hw_config, THIS_MODULE); |
| hw_config->irq *= -1; /* Restore it */ |
| |
| if (hw_config->slots[1] != -1) /* The MPU driver installed itself */ |
| { |
| sscape_mididev = hw_config->slots[1]; |
| midi_devs[hw_config->slots[1]]->coproc = &sscape_coproc_operations; |
| } |
| sscape_write(devc, GA_INTENA_REG, 0x80); /* Master IRQ enable */ |
| devc->ok = 1; |
| devc->failed = 0; |
| } |
| |
| static int detect_ga(sscape_info * devc) |
| { |
| unsigned char save; |
| |
| DDB(printk("Entered Soundscape detect_ga(%x)\n", devc->base)); |
| |
| /* |
| * First check that the address register of "ODIE" is |
| * there and that it has exactly 4 writable bits. |
| * First 4 bits |
| */ |
| |
| if ((save = inb(PORT(ODIE_ADDR))) & 0xf0) |
| { |
| DDB(printk("soundscape: Detect error A\n")); |
| return 0; |
| } |
| outb((0x00), PORT(ODIE_ADDR)); |
| if (inb(PORT(ODIE_ADDR)) != 0x00) |
| { |
| DDB(printk("soundscape: Detect error B\n")); |
| return 0; |
| } |
| outb((0xff), PORT(ODIE_ADDR)); |
| if (inb(PORT(ODIE_ADDR)) != 0x0f) |
| { |
| DDB(printk("soundscape: Detect error C\n")); |
| return 0; |
| } |
| outb((save), PORT(ODIE_ADDR)); |
| |
| /* |
| * Now verify that some indirect registers return zero on some bits. |
| * This may break the driver with some future revisions of "ODIE" but... |
| */ |
| |
| if (sscape_read(devc, 0) & 0x0c) |
| { |
| DDB(printk("soundscape: Detect error D (%x)\n", sscape_read(devc, 0))); |
| return 0; |
| } |
| if (sscape_read(devc, 1) & 0x0f) |
| { |
| DDB(printk("soundscape: Detect error E\n")); |
| return 0; |
| } |
| if (sscape_read(devc, 5) & 0x0f) |
| { |
| DDB(printk("soundscape: Detect error F\n")); |
| return 0; |
| } |
| return 1; |
| } |
| |
| static int sscape_read_host_ctrl(sscape_info* devc) |
| { |
| return host_read(devc); |
| } |
| |
| static void sscape_write_host_ctrl2(sscape_info *devc, int a, int b) |
| { |
| host_command2(devc, a, b); |
| } |
| |
| static int sscape_alloc_dma(sscape_info *devc) |
| { |
| char *start_addr, *end_addr; |
| int dma_pagesize; |
| int sz, size; |
| struct page *page; |
| |
| if (devc->raw_buf != NULL) return 0; /* Already done */ |
| dma_pagesize = (devc->dma < 4) ? (64 * 1024) : (128 * 1024); |
| devc->raw_buf = NULL; |
| devc->buffsize = 8192*4; |
| if (devc->buffsize > dma_pagesize) devc->buffsize = dma_pagesize; |
| start_addr = NULL; |
| /* |
| * Now loop until we get a free buffer. Try to get smaller buffer if |
| * it fails. Don't accept smaller than 8k buffer for performance |
| * reasons. |
| */ |
| while (start_addr == NULL && devc->buffsize > PAGE_SIZE) { |
| for (sz = 0, size = PAGE_SIZE; size < devc->buffsize; sz++, size <<= 1); |
| devc->buffsize = PAGE_SIZE * (1 << sz); |
| start_addr = (char *) __get_free_pages(GFP_ATOMIC|GFP_DMA, sz); |
| if (start_addr == NULL) devc->buffsize /= 2; |
| } |
| |
| if (start_addr == NULL) { |
| printk(KERN_ERR "sscape pnp init error: Couldn't allocate DMA buffer\n"); |
| return 0; |
| } else { |
| /* make some checks */ |
| end_addr = start_addr + devc->buffsize - 1; |
| /* now check if it fits into the same dma-pagesize */ |
| |
| if (((long) start_addr & ~(dma_pagesize - 1)) != ((long) end_addr & ~(dma_pagesize - 1)) |
| || end_addr >= (char *) (MAX_DMA_ADDRESS)) { |
| printk(KERN_ERR "sscape pnp: Got invalid address 0x%lx for %db DMA-buffer\n", (long) start_addr, devc->buffsize); |
| return 0; |
| } |
| } |
| devc->raw_buf = start_addr; |
| devc->raw_buf_phys = virt_to_bus(start_addr); |
| |
| for (page = virt_to_page(start_addr); page <= virt_to_page(end_addr); page++) |
| SetPageReserved(page); |
| return 1; |
| } |
| |
| static void sscape_free_dma(sscape_info *devc) |
| { |
| int sz, size; |
| unsigned long start_addr, end_addr; |
| struct page *page; |
| |
| if (devc->raw_buf == NULL) return; |
| for (sz = 0, size = PAGE_SIZE; size < devc->buffsize; sz++, size <<= 1); |
| start_addr = (unsigned long) devc->raw_buf; |
| end_addr = start_addr + devc->buffsize; |
| |
| for (page = virt_to_page(start_addr); page <= virt_to_page(end_addr); page++) |
| ClearPageReserved(page); |
| |
| free_pages((unsigned long) devc->raw_buf, sz); |
| devc->raw_buf = NULL; |
| } |
| |
| /* Intel version !!!!!!!!! */ |
| |
| static int sscape_start_dma(int chan, unsigned long physaddr, int count, int dma_mode) |
| { |
| unsigned long flags; |
| |
| flags = claim_dma_lock(); |
| disable_dma(chan); |
| clear_dma_ff(chan); |
| set_dma_mode(chan, dma_mode); |
| set_dma_addr(chan, physaddr); |
| set_dma_count(chan, count); |
| enable_dma(chan); |
| release_dma_lock(flags); |
| return 0; |
| } |
| |
| static void sscape_pnp_start_dma(sscape_info* devc, int arg ) |
| { |
| int reg; |
| if (arg == 0) reg = 2; |
| else reg = 3; |
| |
| sscape_write(devc, reg, sscape_read( devc, reg) | 0x01); |
| sscape_write(devc, reg, sscape_read( devc, reg) & 0xFE); |
| } |
| |
| static int sscape_pnp_wait_dma (sscape_info* devc, int arg ) |
| { |
| int reg; |
| unsigned long i; |
| unsigned char d; |
| |
| if (arg == 0) reg = 2; |
| else reg = 3; |
| |
| sleep ( 1 ); |
| i = 0; |
| do { |
| d = sscape_read(devc, reg) & 1; |
| if ( d == 1) break; |
| i++; |
| } while (i < 500000); |
| d = sscape_read(devc, reg) & 1; |
| return d; |
| } |
| |
| static int sscape_pnp_alloc_dma(sscape_info* devc) |
| { |
| /* printk(KERN_INFO "sscape: requesting dma\n"); */ |
| if (request_dma(devc -> dma, "sscape")) return 0; |
| /* printk(KERN_INFO "sscape: dma channel allocated\n"); */ |
| if (!sscape_alloc_dma(devc)) { |
| free_dma(devc -> dma); |
| return 0; |
| }; |
| return 1; |
| } |
| |
| static void sscape_pnp_free_dma(sscape_info* devc) |
| { |
| sscape_free_dma( devc); |
| free_dma(devc -> dma ); |
| /* printk(KERN_INFO "sscape: dma released\n"); */ |
| } |
| |
| static int sscape_pnp_upload_file(sscape_info* devc, char* fn) |
| { |
| int done = 0; |
| int timeout_val; |
| char* data,*dt; |
| int len,l; |
| unsigned long flags; |
| |
| sscape_write( devc, 9, sscape_read(devc, 9 ) & 0x3F ); |
| sscape_write( devc, 2, (devc -> dma << 4) | 0x80 ); |
| sscape_write( devc, 3, 0x20 ); |
| sscape_write( devc, 9, sscape_read( devc, 9 ) | 0x80 ); |
| |
| len = mod_firmware_load(fn, &data); |
| if (len == 0) { |
| printk(KERN_ERR "sscape: file not found: %s\n", fn); |
| return 0; |
| } |
| dt = data; |
| spin_lock_irqsave(&devc->lock,flags); |
| while ( len > 0 ) { |
| if (len > devc -> buffsize) l = devc->buffsize; |
| else l = len; |
| len -= l; |
| memcpy(devc->raw_buf, dt, l); dt += l; |
| sscape_start_dma(devc->dma, devc->raw_buf_phys, l, 0x48); |
| sscape_pnp_start_dma ( devc, 0 ); |
| if (sscape_pnp_wait_dma ( devc, 0 ) == 0) { |
| spin_unlock_irqrestore(&devc->lock,flags); |
| return 0; |
| } |
| } |
| |
| spin_unlock_irqrestore(&devc->lock,flags); |
| vfree(data); |
| |
| outb(0, devc -> base + 2); |
| outb(0, devc -> base); |
| |
| sscape_write ( devc, 9, sscape_read( devc, 9 ) | 0x40); |
| |
| timeout_val = 5 * HZ; |
| while (!done && timeout_val-- > 0) |
| { |
| unsigned char x; |
| sleep(1); |
| x = inb( devc -> base + 3); |
| if (x == 0xff || x == 0xfe) /* OBP startup acknowledge */ |
| { |
| //printk(KERN_ERR "Soundscape: Acknowledge = %x\n", x); |
| done = 1; |
| } |
| } |
| timeout_val = 5 * HZ; |
| done = 0; |
| while (!done && timeout_val-- > 0) |
| { |
| unsigned char x; |
| sleep(1); |
| x = inb( devc -> base + 3); |
| if (x == 0xfe) /* OBP startup acknowledge */ |
| { |
| //printk(KERN_ERR "Soundscape: Acknowledge = %x\n", x); |
| done = 1; |
| } |
| } |
| |
| if ( !done ) printk(KERN_ERR "soundscape: OBP Initialization failed.\n"); |
| |
| sscape_write( devc, 2, devc->ic_type == IC_ODIE ? 0x70 : 0x40); |
| sscape_write( devc, 3, (devc -> dma << 4) + 0x80); |
| return 1; |
| } |
| |
| static void __init sscape_pnp_init_hw(sscape_info* devc) |
| { |
| unsigned char midi_irq = 0, sb_irq = 0; |
| unsigned i; |
| static char code_file_name[23] = "/sndscape/sndscape.cox"; |
| |
| int sscape_joystic_enable = 0x7f; |
| int sscape_mic_enable = 0; |
| int sscape_ext_midi = 0; |
| |
| if ( !sscape_pnp_alloc_dma(devc) ) { |
| printk(KERN_ERR "sscape: faild to allocate dma\n"); |
| return; |
| } |
| |
| for (i = 0; i < 4; i++) { |
| if ( devc -> irq == valid_interrupts[i] ) |
| midi_irq = i; |
| if ( devc -> codec_irq == valid_interrupts[i] ) |
| sb_irq = i; |
| } |
| |
| sscape_write( devc, 5, 0x50); |
| sscape_write( devc, 7, 0x2e); |
| sscape_write( devc, 8, 0x00); |
| |
| sscape_write( devc, 2, devc->ic_type == IC_ODIE ? 0x70 : 0x40); |
| sscape_write( devc, 3, ( devc -> dma << 4) | 0x80); |
| |
| sscape_write (devc, 4, 0xF0 | (midi_irq<<2) | midi_irq); |
| |
| i = 0x10; //sscape_read(devc, 9) & (devc->ic_type == IC_ODIE ? 0xf0 : 0xc0); |
| if (sscape_joystic_enable) i |= 8; |
| |
| sscape_write (devc, 9, i); |
| sscape_write (devc, 6, 0x80); |
| sscape_write (devc, 1, 0x80); |
| |
| if (devc -> codec_type == 2) { |
| sscape_pnp_write_codec( devc, 0x0C, 0x50); |
| sscape_pnp_write_codec( devc, 0x10, sscape_pnp_read_codec( devc, 0x10) & 0x3F); |
| sscape_pnp_write_codec( devc, 0x11, sscape_pnp_read_codec( devc, 0x11) | 0xC0); |
| sscape_pnp_write_codec( devc, 29, 0x20); |
| } |
| |
| if (sscape_pnp_upload_file(devc, "/sndscape/scope.cod") == 0 ) { |
| printk(KERN_ERR "sscape: faild to upload file /sndscape/scope.cod\n"); |
| sscape_pnp_free_dma(devc); |
| return; |
| } |
| |
| i = sscape_read_host_ctrl( devc ); |
| |
| if ( (i & 0x0F) > 7 ) { |
| printk(KERN_ERR "sscape: scope.cod faild\n"); |
| sscape_pnp_free_dma(devc); |
| return; |
| } |
| if ( i & 0x10 ) sscape_write( devc, 7, 0x2F); |
| code_file_name[21] = (char) ( i & 0x0F) + 0x30; |
| if (sscape_pnp_upload_file( devc, code_file_name) == 0) { |
| printk(KERN_ERR "sscape: faild to upload file %s\n", code_file_name); |
| sscape_pnp_free_dma(devc); |
| return; |
| } |
| |
| if (devc->ic_type != IC_ODIE) { |
| sscape_pnp_write_codec( devc, 10, (sscape_pnp_read_codec(devc, 10) & 0x7f) | |
| ( sscape_mic_enable == 0 ? 0x00 : 0x80) ); |
| } |
| sscape_write_host_ctrl2( devc, 0x84, 0x64 ); /* MIDI volume */ |
| sscape_write_host_ctrl2( devc, 0x86, 0x64 ); /* MIDI volume?? */ |
| sscape_write_host_ctrl2( devc, 0x8A, sscape_ext_midi); |
| |
| sscape_pnp_write_codec ( devc, 6, 0x3f ); //WAV_VOL |
| sscape_pnp_write_codec ( devc, 7, 0x3f ); //WAV_VOL |
| sscape_pnp_write_codec ( devc, 2, 0x1F ); //WD_CDXVOLL |
| sscape_pnp_write_codec ( devc, 3, 0x1F ); //WD_CDXVOLR |
| |
| if (devc -> codec_type == 1) { |
| sscape_pnp_write_codec ( devc, 4, 0x1F ); |
| sscape_pnp_write_codec ( devc, 5, 0x1F ); |
| sscape_write_host_ctrl2( devc, 0x88, sscape_mic_enable); |
| } else { |
| int t; |
| sscape_pnp_write_codec ( devc, 0x10, 0x1F << 1); |
| sscape_pnp_write_codec ( devc, 0x11, 0xC0 | (0x1F << 1)); |
| |
| t = sscape_pnp_read_codec( devc, 0x00) & 0xDF; |
| if ( (sscape_mic_enable == 0)) t |= 0; |
| else t |= 0x20; |
| sscape_pnp_write_codec ( devc, 0x00, t); |
| t = sscape_pnp_read_codec( devc, 0x01) & 0xDF; |
| if ( (sscape_mic_enable == 0) ) t |= 0; |
| else t |= 0x20; |
| sscape_pnp_write_codec ( devc, 0x01, t); |
| sscape_pnp_write_codec ( devc, 0x40 | 29 , 0x20); |
| outb(0, devc -> codec); |
| } |
| if (devc -> ic_type == IC_OPUS ) { |
| int i = sscape_read( devc, 9 ); |
| sscape_write( devc, 9, i | 3 ); |
| sscape_write( devc, 3, 0x40); |
| |
| if (request_region(0x228, 1, "sscape setup junk")) { |
| outb(0, 0x228); |
| release_region(0x228,1); |
| } |
| sscape_write( devc, 3, (devc -> dma << 4) | 0x80); |
| sscape_write( devc, 9, i ); |
| } |
| |
| host_close ( devc ); |
| sscape_pnp_free_dma(devc); |
| } |
| |
| static int __init detect_sscape_pnp(sscape_info* devc) |
| { |
| long i, irq_bits = 0xff; |
| unsigned int d; |
| |
| DDB(printk("Entered detect_sscape_pnp(%x)\n", devc->base)); |
| |
| if (!request_region(devc->codec, 2, "sscape codec")) { |
| printk(KERN_ERR "detect_sscape_pnp: port %x is not free\n", devc->codec); |
| return 0; |
| } |
| |
| if ((inb(devc->base + 2) & 0x78) != 0) |
| goto fail; |
| |
| d = inb ( devc -> base + 4) & 0xF0; |
| if (d & 0x80) |
| goto fail; |
| |
| if (d == 0) { |
| devc->codec_type = 1; |
| devc->ic_type = IC_ODIE; |
| } else if ( (d & 0x60) != 0) { |
| devc->codec_type = 2; |
| devc->ic_type = IC_OPUS; |
| } else if ( (d & 0x40) != 0) { /* WTF? */ |
| devc->codec_type = 2; |
| devc->ic_type = IC_ODIE; |
| } else |
| goto fail; |
| |
| sscape_is_pnp = 1; |
| |
| outb(0xFA, devc -> base+4); |
| if ((inb( devc -> base+4) & 0x9F) != 0x0A) |
| goto fail; |
| outb(0xFE, devc -> base+4); |
| if ( (inb(devc -> base+4) & 0x9F) != 0x0E) |
| goto fail; |
| if ( (inb(devc -> base+5) & 0x9F) != 0x0E) |
| goto fail; |
| |
| if (devc->codec_type == 2) { |
| if (devc->codec != devc->base + 8) { |
| printk("soundscape warning: incorrect codec port specified\n"); |
| goto fail; |
| } |
| d = 0x10 | (sscape_read(devc, 9) & 0xCF); |
| sscape_write(devc, 9, d); |
| sscape_write(devc, 6, 0x80); |
| } else { |
| //todo: check codec is not base + 8 |
| } |
| |
| d = (sscape_read(devc, 9) & 0x3F) | 0xC0; |
| sscape_write(devc, 9, d); |
| |
| for (i = 0; i < 550000; i++) |
| if ( !(inb(devc -> codec) & 0x80) ) break; |
| |
| d = inb(devc -> codec); |
| if (d & 0x80) |
| goto fail; |
| if ( inb(devc -> codec + 2) == 0xFF) |
| goto fail; |
| |
| sscape_write(devc, 9, sscape_read(devc, 9) & 0x3F ); |
| |
| d = inb(devc -> codec) & 0x80; |
| if ( d == 0) { |
| printk(KERN_INFO "soundscape: hardware detected\n"); |
| valid_interrupts = valid_interrupts_new; |
| } else { |
| printk(KERN_INFO "soundscape: board looks like media fx\n"); |
| valid_interrupts = valid_interrupts_old; |
| old_hardware = 1; |
| } |
| |
| sscape_write( devc, 9, 0xC0 | (sscape_read(devc, 9) & 0x3F) ); |
| |
| for (i = 0; i < 550000; i++) |
| if ( !(inb(devc -> codec) & 0x80)) |
| break; |
| |
| sscape_pnp_init_hw(devc); |
| |
| for (i = 0; i < 4; i++) |
| { |
| if (devc->codec_irq == valid_interrupts[i]) { |
| irq_bits = i; |
| break; |
| } |
| } |
| sscape_write(devc, GA_INTENA_REG, 0x00); |
| sscape_write(devc, GA_DMACFG_REG, 0x50); |
| sscape_write(devc, GA_DMAA_REG, 0x70); |
| sscape_write(devc, GA_DMAB_REG, 0x20); |
| sscape_write(devc, GA_INTCFG_REG, 0xf0); |
| sscape_write(devc, GA_CDCFG_REG, 0x89 | (devc->dma << 4) | (irq_bits << 1)); |
| |
| sscape_pnp_write_codec( devc, 0, sscape_pnp_read_codec( devc, 0) | 0x20); |
| sscape_pnp_write_codec( devc, 0, sscape_pnp_read_codec( devc, 1) | 0x20); |
| |
| return 1; |
| fail: |
| release_region(devc->codec, 2); |
| return 0; |
| } |
| |
| static int __init probe_sscape(struct address_info *hw_config) |
| { |
| devc->base = hw_config->io_base; |
| devc->irq = hw_config->irq; |
| devc->dma = hw_config->dma; |
| devc->osp = hw_config->osp; |
| |
| #ifdef SSCAPE_DEBUG1 |
| /* |
| * Temporary debugging aid. Print contents of the registers before |
| * changing them. |
| */ |
| { |
| int i; |
| |
| for (i = 0; i < 13; i++) |
| printk("I%d = %02x (old value)\n", i, sscape_read(devc, i)); |
| } |
| #endif |
| devc->failed = 1; |
| |
| sscape_ports = request_region(devc->base, 2, "mpu401"); |
| if (!sscape_ports) |
| return 0; |
| |
| if (!request_region(devc->base + 2, 6, "SoundScape")) { |
| release_region(devc->base, 2); |
| return 0; |
| } |
| |
| if (!detect_ga(devc)) { |
| if (detect_sscape_pnp(devc)) |
| return 1; |
| release_region(devc->base, 2); |
| release_region(devc->base + 2, 6); |
| return 0; |
| } |
| |
| if (old_hardware) /* Check that it's really an old Spea/Reveal card. */ |
| { |
| unsigned char tmp; |
| int cc; |
| |
| if (!((tmp = sscape_read(devc, GA_HMCTL_REG)) & 0xc0)) |
| { |
| sscape_write(devc, GA_HMCTL_REG, tmp | 0x80); |
| for (cc = 0; cc < 200000; ++cc) |
| inb(devc->base + ODIE_ADDR); |
| } |
| } |
| return 1; |
| } |
| |
| static int __init init_ss_ms_sound(struct address_info *hw_config) |
| { |
| int i, irq_bits = 0xff; |
| int ad_flags = 0; |
| struct resource *ports; |
| |
| if (devc->failed) |
| { |
| printk(KERN_ERR "soundscape: Card not detected\n"); |
| return 0; |
| } |
| if (devc->ok == 0) |
| { |
| printk(KERN_ERR "soundscape: Invalid initialization order.\n"); |
| return 0; |
| } |
| for (i = 0; i < 4; i++) |
| { |
| if (hw_config->irq == valid_interrupts[i]) |
| { |
| irq_bits = i; |
| break; |
| } |
| } |
| if (irq_bits == 0xff) { |
| printk(KERN_ERR "soundscape: Invalid MSS IRQ%d\n", hw_config->irq); |
| return 0; |
| } |
| |
| if (old_hardware) |
| ad_flags = 0x12345677; /* Tell that we may have a CS4248 chip (Spea-V7 Media FX) */ |
| else if (sscape_is_pnp) |
| ad_flags = 0x87654321; /* Tell that we have a soundscape pnp with 1845 chip */ |
| |
| ports = request_region(hw_config->io_base, 4, "ad1848"); |
| if (!ports) { |
| printk(KERN_ERR "soundscape: ports busy\n"); |
| return 0; |
| } |
| |
| if (!ad1848_detect(ports, &ad_flags, hw_config->osp)) { |
| release_region(hw_config->io_base, 4); |
| return 0; |
| } |
| |
| if (!sscape_is_pnp) /*pnp is already setup*/ |
| { |
| /* |
| * Setup the DMA polarity. |
| */ |
| sscape_write(devc, GA_DMACFG_REG, 0x50); |
| |
| /* |
| * Take the gate-array off of the DMA channel. |
| */ |
| sscape_write(devc, GA_DMAB_REG, 0x20); |
| |
| /* |
| * Init the AD1848 (CD-ROM) config reg. |
| */ |
| sscape_write(devc, GA_CDCFG_REG, 0x89 | (hw_config->dma << 4) | (irq_bits << 1)); |
| } |
| |
| if (hw_config->irq == devc->irq) |
| printk(KERN_WARNING "soundscape: Warning! The WSS mode can't share IRQ with MIDI\n"); |
| |
| hw_config->slots[0] = ad1848_init( |
| sscape_is_pnp ? "SoundScape" : "SoundScape PNP", |
| ports, |
| hw_config->irq, |
| hw_config->dma, |
| hw_config->dma, |
| 0, |
| devc->osp, |
| THIS_MODULE); |
| |
| |
| if (hw_config->slots[0] != -1) /* The AD1848 driver installed itself */ |
| { |
| audio_devs[hw_config->slots[0]]->coproc = &sscape_coproc_operations; |
| devc->codec_audiodev = hw_config->slots[0]; |
| devc->my_audiodev = hw_config->slots[0]; |
| |
| /* Set proper routings here (what are they) */ |
| AD1848_REROUTE(SOUND_MIXER_LINE1, SOUND_MIXER_LINE); |
| } |
| |
| #ifdef SSCAPE_DEBUG5 |
| /* |
| * Temporary debugging aid. Print contents of the registers |
| * after the AD1848 device has been initialized. |
| */ |
| { |
| int i; |
| |
| for (i = 0; i < 13; i++) |
| printk("I%d = %02x\n", i, sscape_read(devc, i)); |
| } |
| #endif |
| return 1; |
| } |
| |
| static void __exit unload_sscape(struct address_info *hw_config) |
| { |
| release_region(devc->base + 2, 6); |
| unload_mpu401(hw_config); |
| if (sscape_is_pnp) |
| release_region(devc->codec, 2); |
| } |
| |
| static void __exit unload_ss_ms_sound(struct address_info *hw_config) |
| { |
| ad1848_unload(hw_config->io_base, |
| hw_config->irq, |
| devc->dma, |
| devc->dma, |
| 0); |
| sound_unload_audiodev(hw_config->slots[0]); |
| } |
| |
| static struct address_info cfg; |
| static struct address_info cfg_mpu; |
| |
| static int __initdata spea = -1; |
| static int mss = 0; |
| static int __initdata dma = -1; |
| static int __initdata irq = -1; |
| static int __initdata io = -1; |
| static int __initdata mpu_irq = -1; |
| static int __initdata mpu_io = -1; |
| |
| module_param(dma, int, 0); |
| module_param(irq, int, 0); |
| module_param(io, int, 0); |
| module_param(spea, int, 0); /* spea=0/1 set the old_hardware */ |
| module_param(mpu_irq, int, 0); |
| module_param(mpu_io, int, 0); |
| module_param(mss, int, 0); |
| |
| static int __init init_sscape(void) |
| { |
| printk(KERN_INFO "Soundscape driver Copyright (C) by Hannu Savolainen 1993-1996\n"); |
| |
| cfg.irq = irq; |
| cfg.dma = dma; |
| cfg.io_base = io; |
| |
| cfg_mpu.irq = mpu_irq; |
| cfg_mpu.io_base = mpu_io; |
| /* WEH - Try to get right dma channel */ |
| cfg_mpu.dma = dma; |
| |
| devc->codec = cfg.io_base; |
| devc->codec_irq = cfg.irq; |
| devc->codec_type = 0; |
| devc->ic_type = 0; |
| devc->raw_buf = NULL; |
| spin_lock_init(&devc->lock); |
| |
| if (cfg.dma == -1 || cfg.irq == -1 || cfg.io_base == -1) { |
| printk(KERN_ERR "DMA, IRQ, and IO port must be specified.\n"); |
| return -EINVAL; |
| } |
| |
| if (cfg_mpu.irq == -1 && cfg_mpu.io_base != -1) { |
| printk(KERN_ERR "MPU_IRQ must be specified if MPU_IO is set.\n"); |
| return -EINVAL; |
| } |
| |
| if(spea != -1) { |
| old_hardware = spea; |
| printk(KERN_INFO "Forcing %s hardware support.\n", |
| spea?"new":"old"); |
| } |
| if (probe_sscape(&cfg_mpu) == 0) |
| return -ENODEV; |
| |
| attach_sscape(&cfg_mpu); |
| |
| mss = init_ss_ms_sound(&cfg); |
| |
| return 0; |
| } |
| |
| static void __exit cleanup_sscape(void) |
| { |
| if (mss) |
| unload_ss_ms_sound(&cfg); |
| unload_sscape(&cfg_mpu); |
| } |
| |
| module_init(init_sscape); |
| module_exit(cleanup_sscape); |
| |
| #ifndef MODULE |
| static int __init setup_sscape(char *str) |
| { |
| /* io, irq, dma, mpu_io, mpu_irq */ |
| int ints[6]; |
| |
| str = get_options(str, ARRAY_SIZE(ints), ints); |
| |
| io = ints[1]; |
| irq = ints[2]; |
| dma = ints[3]; |
| mpu_io = ints[4]; |
| mpu_irq = ints[5]; |
| |
| return 1; |
| } |
| |
| __setup("sscape=", setup_sscape); |
| #endif |
| MODULE_LICENSE("GPL"); |