ide: use I/O ops directly part #2 (take 2)
v2:
- bump host driver versions (as suggested by Sergei)
- use I/O ops directly in drivers/ide/setup-pci.c
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
diff --git a/drivers/ide/pci/tc86c001.c b/drivers/ide/pci/tc86c001.c
index 9f50927..04fe9b7 100644
--- a/drivers/ide/pci/tc86c001.c
+++ b/drivers/ide/pci/tc86c001.c
@@ -1,5 +1,5 @@
/*
- * drivers/ide/pci/tc86c001.c Version 1.00 Dec 12, 2006
+ * drivers/ide/pci/tc86c001.c Version 1.01 Sep 5, 2007
*
* Copyright (C) 2002 Toshiba Corporation
* Copyright (C) 2005-2006 MontaVista Software, Inc. <source@mvista.com>
@@ -17,7 +17,7 @@
{
ide_hwif_t *hwif = HWIF(drive);
unsigned long scr_port = hwif->config_data + (drive->dn ? 0x02 : 0x00);
- u16 mode, scr = hwif->INW(scr_port);
+ u16 mode, scr = inw(scr_port);
switch (speed) {
case XFER_UDMA_4: mode = 0x00c0; break;
@@ -65,7 +65,7 @@
ide_hwif_t *hwif = HWIF(drive);
ide_expiry_t *expiry = ide_get_hwifdata(hwif);
ide_hwgroup_t *hwgroup = HWGROUP(drive);
- u8 dma_stat = hwif->INB(hwif->dma_status);
+ u8 dma_stat = inb(hwif->dma_status);
/* Restore a higher level driver's expiry handler first. */
hwgroup->expiry = expiry;
@@ -73,7 +73,7 @@
if ((dma_stat & 5) == 1) { /* DMA active and no interrupt */
unsigned long sc_base = hwif->config_data;
unsigned long twcr_port = sc_base + (drive->dn ? 0x06 : 0x04);
- u8 dma_cmd = hwif->INB(hwif->dma_command);
+ u8 dma_cmd = inb(hwif->dma_command);
printk(KERN_WARNING "%s: DMA interrupt possibly stuck, "
"attempting recovery...\n", drive->name);
@@ -135,7 +135,7 @@
u16 scr1;
/* System Control 1 Register bit 11 (ATA Hard Reset) read */
- scr1 = hwif->INW(sc_base + 0x00);
+ scr1 = inw(sc_base + 0x00);
switch (state) {
case BUSSTATE_ON:
@@ -165,7 +165,7 @@
static void __devinit init_hwif_tc86c001(ide_hwif_t *hwif)
{
unsigned long sc_base = pci_resource_start(hwif->pci_dev, 5);
- u16 scr1 = hwif->INW(sc_base + 0x00);;
+ u16 scr1 = inw(sc_base + 0x00);
/* System Control 1 Register bit 15 (Soft Reset) set */
outw(scr1 | 0x8000, sc_base + 0x00);
@@ -205,7 +205,7 @@
* System Control 1 Register bit 13 (PDIAGN):
* 0=80-pin cable, 1=40-pin cable
*/
- scr1 = hwif->INW(sc_base + 0x00);
+ scr1 = inw(sc_base + 0x00);
hwif->cbl = (scr1 & 0x2000) ? ATA_CBL_PATA40 : ATA_CBL_PATA80;
}
}