Merge branch 'powerpc-next' of master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc
diff --git a/arch/powerpc/kernel/cpu_setup_6xx.S b/arch/powerpc/kernel/cpu_setup_6xx.S
index f1ee0b3..72d1d73 100644
--- a/arch/powerpc/kernel/cpu_setup_6xx.S
+++ b/arch/powerpc/kernel/cpu_setup_6xx.S
@@ -17,7 +17,13 @@
#include <asm/cache.h>
_GLOBAL(__setup_cpu_603)
- b setup_common_caches
+ mflr r4
+BEGIN_FTR_SECTION
+ bl __init_fpu_registers
+END_FTR_SECTION_IFCLR(CPU_FTR_FPU_UNAVAILABLE)
+ bl setup_common_caches
+ mtlr r4
+ blr
_GLOBAL(__setup_cpu_604)
mflr r4
bl setup_common_caches
diff --git a/arch/ppc/8260_io/fcc_enet.c b/arch/ppc/8260_io/fcc_enet.c
index bcc3aa9..d38b57e 100644
--- a/arch/ppc/8260_io/fcc_enet.c
+++ b/arch/ppc/8260_io/fcc_enet.c
@@ -165,9 +165,6 @@
#ifdef CONFIG_SBC82xx
#define F1_RXCLK 9
#define F1_TXCLK 10
-#elif defined(CONFIG_ADS8272)
-#define F1_RXCLK 11
-#define F1_TXCLK 10
#else
#define F1_RXCLK 12
#define F1_TXCLK 11
@@ -175,13 +172,8 @@
/* FCC2 Clock Source Configuration. There are board specific.
Can only choose from CLK13-16 */
-#ifdef CONFIG_ADS8272
-#define F2_RXCLK 15
-#define F2_TXCLK 16
-#else
#define F2_RXCLK 13
#define F2_TXCLK 14
-#endif
/* FCC3 Clock Source Configuration. There are board specific.
Can only choose from CLK13-16 */
@@ -289,10 +281,7 @@
/* TQM8260 has MDIO and MDCK on PC30 and PC31 respectively */
#define PC_MDIO ((uint)0x00000002)
#define PC_MDCK ((uint)0x00000001)
-#elif defined(CONFIG_ADS8272)
-#define PC_MDIO ((uint)0x00002000)
-#define PC_MDCK ((uint)0x00001000)
-#elif defined(CONFIG_EST8260) || defined(CONFIG_ADS8260) || defined(CONFIG_PQ2FADS)
+#elif defined(CONFIG_EST8260) || defined(CONFIG_ADS8260)
#define PC_MDIO ((uint)0x00400000)
#define PC_MDCK ((uint)0x00200000)
#else
@@ -2118,11 +2107,6 @@
printk("Can't get FCC IRQ %d\n", fip->fc_interrupt);
#ifdef PHY_INTERRUPT
-#ifdef CONFIG_ADS8272
- if (request_irq(PHY_INTERRUPT, mii_link_interrupt, IRQF_SHARED,
- "mii", dev) < 0)
- printk(KERN_CRIT "Can't get MII IRQ %d\n", PHY_INTERRUPT);
-#else
/* Make IRQn edge triggered. This does not work if PHY_INTERRUPT is
* on Port C.
*/
@@ -2132,7 +2116,6 @@
if (request_irq(PHY_INTERRUPT, mii_link_interrupt, 0,
"mii", dev) < 0)
printk(KERN_CRIT "Can't get MII IRQ %d\n", PHY_INTERRUPT);
-#endif
#endif /* PHY_INTERRUPT */
/* Set GFMR to enable Ethernet operating mode.
diff --git a/arch/ppc/8xx_io/enet.c b/arch/ppc/8xx_io/enet.c
index c6d047a..5899aea 100644
--- a/arch/ppc/8xx_io/enet.c
+++ b/arch/ppc/8xx_io/enet.c
@@ -946,29 +946,6 @@
*((volatile uint *)BCSR1) &= ~BCSR1_ETHEN;
#endif
-#ifdef CONFIG_MPC885ADS
-
- /* Deassert PHY reset and enable the PHY.
- */
- {
- volatile uint __iomem *bcsr = ioremap(BCSR_ADDR, BCSR_SIZE);
- uint tmp;
-
- tmp = in_be32(bcsr + 1 /* BCSR1 */);
- tmp |= BCSR1_ETHEN;
- out_be32(bcsr + 1, tmp);
- tmp = in_be32(bcsr + 4 /* BCSR4 */);
- tmp |= BCSR4_ETH10_RST;
- out_be32(bcsr + 4, tmp);
- iounmap(bcsr);
- }
-
- /* On MPC885ADS SCC ethernet PHY defaults to the full duplex mode
- * upon reset. SCC is set to half duplex by default. So this
- * inconsistency should be better fixed by the software.
- */
-#endif
-
dev->base_addr = (unsigned long)ep;
#if 0
dev->name = "CPM_ENET";
diff --git a/arch/ppc/Kconfig b/arch/ppc/Kconfig
index abc877f..0f1863e 100644
--- a/arch/ppc/Kconfig
+++ b/arch/ppc/Kconfig
@@ -372,22 +372,6 @@
bool "FADS"
select FADS
-config MPC86XADS
- bool "MPC86XADS"
- help
- MPC86x Application Development System by Freescale Semiconductor.
- The MPC86xADS is meant to serve as a platform for s/w and h/w
- development around the MPC86X processor families.
- select FADS
-
-config MPC885ADS
- bool "MPC885ADS"
- help
- Freescale Semiconductor MPC885 Application Development System (ADS).
- Also known as DUET.
- The MPC885ADS is meant to serve as a platform for s/w and h/w
- development around the MPC885 processor family.
-
config TQM823L
bool "TQM823L"
help
@@ -479,53 +463,6 @@
endchoice
-menu "Freescale Ethernet driver platform-specific options"
- depends on FS_ENET
-
- config MPC8xx_SECOND_ETH
- bool "Second Ethernet channel"
- depends on (MPC885ADS || MPC86XADS)
- default y
- help
- This enables support for second Ethernet on MPC885ADS and MPC86xADS boards.
- The latter will use SCC1, for 885ADS you can select it below.
-
- choice
- prompt "Second Ethernet channel"
- depends on MPC8xx_SECOND_ETH
- default MPC8xx_SECOND_ETH_FEC2
-
- config MPC8xx_SECOND_ETH_FEC2
- bool "FEC2"
- depends on MPC885ADS
- help
- Enable FEC2 to serve as 2-nd Ethernet channel. Note that SMC2
- (often 2-nd UART) will not work if this is enabled.
-
- config MPC8xx_SECOND_ETH_SCC1
- bool "SCC1"
- depends on MPC86XADS
- select MPC8xx_SCC_ENET_FIXED
- help
- Enable SCC1 to serve as 2-nd Ethernet channel. Note that SMC1
- (often 1-nd UART) will not work if this is enabled.
-
- config MPC8xx_SECOND_ETH_SCC3
- bool "SCC3"
- depends on MPC885ADS
- help
- Enable SCC3 to serve as 2-nd Ethernet channel. Note that SMC1
- (often 1-nd UART) will not work if this is enabled.
-
- endchoice
-
- config MPC8xx_SCC_ENET_FIXED
- depends on MPC8xx_SECOND_ETH_SCC
- default n
- bool "Use fixed MII-less mode for SCC Ethernet"
-
-endmenu
-
choice
prompt "Machine Type"
depends on 6xx
@@ -666,9 +603,6 @@
End of Life: not yet :-)
URL: <http://www.denx.de/PDF/TQM82xx_SPEC_Rev005.pdf>
-config ADS8272
- bool "ADS8272"
-
config PQ2FADS
bool "Freescale-PQ2FADS"
help
@@ -698,11 +632,6 @@
platform.
endchoice
-config PQ2ADS
- bool
- depends on ADS8272
- default y
-
config TQM8xxL
bool
depends on 8xx && (TQM823L || TQM850L || FPS850L || TQM855L || TQM860L)
@@ -725,15 +654,6 @@
this option means that you wish to build a kernel for a machine with
an 8260 class CPU.
-config 8272
- bool
- depends on 6xx
- default y if ADS8272
- select 8260
- help
- The MPC8272 CPM has a different internal dpram setup than other CPM2
- devices
-
config CPM1
bool
depends on 8xx
@@ -1069,7 +989,7 @@
config 8260_PCI9
bool "Enable workaround for MPC826x erratum PCI 9"
- depends on PCI_8260 && !ADS8272
+ depends on PCI_8260
default y
choice
diff --git a/arch/ppc/configs/ads8272_defconfig b/arch/ppc/configs/ads8272_defconfig
deleted file mode 100644
index 6619f91..0000000
--- a/arch/ppc/configs/ads8272_defconfig
+++ /dev/null
@@ -1,930 +0,0 @@
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.21-rc5
-# Wed Apr 4 20:55:16 2007
-#
-CONFIG_MMU=y
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-CONFIG_ARCH_HAS_ILOG2_U32=y
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_PPC=y
-CONFIG_PPC32=y
-CONFIG_GENERIC_NVRAM=y
-CONFIG_GENERIC_FIND_NEXT_BIT=y
-CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
-CONFIG_ARCH_MAY_HAVE_PC_FDC=y
-CONFIG_GENERIC_BUG=y
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# Code maturity level options
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-
-#
-# General setup
-#
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-# CONFIG_IPC_NS is not set
-CONFIG_SYSVIPC_SYSCTL=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_UTS_NS is not set
-# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_SYSFS_DEPRECATED=y
-# CONFIG_RELAY is not set
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_INITRAMFS_SOURCE=""
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_SYSCTL=y
-CONFIG_EMBEDDED=y
-CONFIG_SYSCTL_SYSCALL=y
-# CONFIG_KALLSYMS is not set
-# CONFIG_HOTPLUG is not set
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-# CONFIG_EPOLL is not set
-CONFIG_SHMEM=y
-CONFIG_SLAB=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-# CONFIG_SLOB is not set
-
-#
-# Loadable module support
-#
-# CONFIG_MODULES is not set
-
-#
-# Block layer
-#
-CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-# CONFIG_DEFAULT_AS is not set
-# CONFIG_DEFAULT_DEADLINE is not set
-CONFIG_DEFAULT_CFQ=y
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="cfq"
-
-#
-# Processor
-#
-CONFIG_6xx=y
-# CONFIG_40x is not set
-# CONFIG_44x is not set
-# CONFIG_8xx is not set
-# CONFIG_E200 is not set
-# CONFIG_E500 is not set
-CONFIG_PPC_FPU=y
-# CONFIG_PPC_DCR_NATIVE is not set
-# CONFIG_KEXEC is not set
-# CONFIG_CPU_FREQ is not set
-# CONFIG_WANT_EARLY_SERIAL is not set
-CONFIG_EMBEDDEDBOOT=y
-CONFIG_PPC_STD_MMU=y
-
-#
-# Platform options
-#
-
-#
-# Freescale Ethernet driver platform-specific options
-#
-# CONFIG_PPC_PREP is not set
-# CONFIG_APUS is not set
-# CONFIG_KATANA is not set
-# CONFIG_WILLOW is not set
-# CONFIG_CPCI690 is not set
-# CONFIG_POWERPMC250 is not set
-# CONFIG_CHESTNUT is not set
-# CONFIG_SPRUCE is not set
-# CONFIG_HDPU is not set
-# CONFIG_EV64260 is not set
-# CONFIG_LOPEC is not set
-# CONFIG_MVME5100 is not set
-# CONFIG_PPLUS is not set
-# CONFIG_PRPMC750 is not set
-# CONFIG_PRPMC800 is not set
-# CONFIG_SANDPOINT is not set
-# CONFIG_RADSTONE_PPC7D is not set
-# CONFIG_PAL4 is not set
-# CONFIG_EST8260 is not set
-# CONFIG_SBC82xx is not set
-# CONFIG_SBS8260 is not set
-# CONFIG_RPX8260 is not set
-# CONFIG_TQM8260 is not set
-CONFIG_ADS8272=y
-# CONFIG_PQ2FADS is not set
-# CONFIG_LITE5200 is not set
-# CONFIG_MPC834x_SYS is not set
-# CONFIG_EV64360 is not set
-CONFIG_PQ2ADS=y
-CONFIG_8260=y
-CONFIG_8272=y
-CONFIG_CPM2=y
-# CONFIG_PC_KEYBOARD is not set
-# CONFIG_SMP is not set
-# CONFIG_HIGHMEM is not set
-CONFIG_ARCH_POPULATES_NODE_MAP=y
-# CONFIG_HZ_100 is not set
-CONFIG_HZ_250=y
-# CONFIG_HZ_300 is not set
-# CONFIG_HZ_1000 is not set
-CONFIG_HZ=250
-CONFIG_PREEMPT_NONE=y
-# CONFIG_PREEMPT_VOLUNTARY is not set
-# CONFIG_PREEMPT is not set
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-CONFIG_SPLIT_PTLOCK_CPUS=4
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_MISC is not set
-# CONFIG_CMDLINE_BOOL is not set
-# CONFIG_PM is not set
-CONFIG_SECCOMP=y
-CONFIG_ISA_DMA_API=y
-
-#
-# Bus options
-#
-CONFIG_ZONE_DMA=y
-# CONFIG_PPC_I8259 is not set
-CONFIG_PPC_INDIRECT_PCI=y
-CONFIG_PCI=y
-CONFIG_PCI_DOMAINS=y
-CONFIG_PCI_8260=y
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
-
-#
-# Advanced setup
-#
-# CONFIG_ADVANCED_OPTIONS is not set
-
-#
-# Default settings for advanced configuration options are used
-#
-CONFIG_HIGHMEM_START=0xfe000000
-CONFIG_LOWMEM_SIZE=0x30000000
-CONFIG_KERNEL_START=0xc0000000
-CONFIG_TASK_SIZE=0x80000000
-CONFIG_BOOT_LOAD=0x00400000
-
-#
-# Networking
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-# CONFIG_NETDEBUG is not set
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-CONFIG_XFRM=y
-# CONFIG_XFRM_USER is not set
-# CONFIG_XFRM_SUB_POLICY is not set
-# CONFIG_XFRM_MIGRATE is not set
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_IP_MROUTE is not set
-# CONFIG_ARPD is not set
-CONFIG_SYN_COOKIES=y
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-CONFIG_INET_XFRM_MODE_TRANSPORT=y
-CONFIG_INET_XFRM_MODE_TUNNEL=y
-CONFIG_INET_XFRM_MODE_BEET=y
-CONFIG_INET_DIAG=y
-CONFIG_INET_TCP_DIAG=y
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-# CONFIG_TCP_MD5SIG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
-# CONFIG_NETWORK_SECMARK is not set
-# CONFIG_NETFILTER is not set
-
-#
-# DCCP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_DCCP is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_SCTP is not set
-
-#
-# TIPC Configuration (EXPERIMENTAL)
-#
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-# CONFIG_IEEE80211 is not set
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_STANDALONE=y
-CONFIG_PREVENT_FIRMWARE_BUILD=y
-# CONFIG_SYS_HYPERVISOR is not set
-
-#
-# Connector - unified userspace <-> kernelspace linker
-#
-# CONFIG_CONNECTOR is not set
-
-#
-# Memory Technology Devices (MTD)
-#
-# CONFIG_MTD is not set
-
-#
-# Parallel port support
-#
-# CONFIG_PARPORT is not set
-
-#
-# Plug and Play support
-#
-# CONFIG_PNPACPI is not set
-
-#
-# Block devices
-#
-# CONFIG_BLK_DEV_FD is not set
-# CONFIG_BLK_CPQ_DA is not set
-# CONFIG_BLK_CPQ_CISS_DA is not set
-# CONFIG_BLK_DEV_DAC960 is not set
-# CONFIG_BLK_DEV_UMEM is not set
-# CONFIG_BLK_DEV_COW_COMMON is not set
-CONFIG_BLK_DEV_LOOP=y
-# CONFIG_BLK_DEV_CRYPTOLOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
-# CONFIG_BLK_DEV_SX8 is not set
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_COUNT=16
-CONFIG_BLK_DEV_RAM_SIZE=32768
-CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
-# CONFIG_CDROM_PKTCDVD is not set
-# CONFIG_ATA_OVER_ETH is not set
-
-#
-# Misc devices
-#
-# CONFIG_SGI_IOC4 is not set
-# CONFIG_TIFM_CORE is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_RAID_ATTRS is not set
-# CONFIG_SCSI is not set
-# CONFIG_SCSI_NETLINK is not set
-
-#
-# Serial ATA (prod) and Parallel ATA (experimental) drivers
-#
-# CONFIG_ATA is not set
-
-#
-# Multi-device support (RAID and LVM)
-#
-# CONFIG_MD is not set
-
-#
-# Fusion MPT device support
-#
-# CONFIG_FUSION is not set
-
-#
-# IEEE 1394 (FireWire) support
-#
-# CONFIG_IEEE1394 is not set
-
-#
-# I2O device support
-#
-# CONFIG_I2O is not set
-
-#
-# Macintosh device drivers
-#
-# CONFIG_MAC_EMUMOUSEBTN is not set
-# CONFIG_WINDFARM is not set
-
-#
-# Network device support
-#
-CONFIG_NETDEVICES=y
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-
-#
-# ARCnet devices
-#
-# CONFIG_ARCNET is not set
-
-#
-# PHY device support
-#
-CONFIG_PHYLIB=y
-
-#
-# MII PHY device drivers
-#
-# CONFIG_MARVELL_PHY is not set
-CONFIG_DAVICOM_PHY=y
-# CONFIG_QSEMI_PHY is not set
-# CONFIG_LXT_PHY is not set
-# CONFIG_CICADA_PHY is not set
-# CONFIG_VITESSE_PHY is not set
-# CONFIG_SMSC_PHY is not set
-# CONFIG_BROADCOM_PHY is not set
-# CONFIG_FIXED_PHY is not set
-
-#
-# Ethernet (10 or 100Mbit)
-#
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-# CONFIG_HAPPYMEAL is not set
-# CONFIG_SUNGEM is not set
-# CONFIG_CASSINI is not set
-# CONFIG_NET_VENDOR_3COM is not set
-
-#
-# Tulip family network device support
-#
-# CONFIG_NET_TULIP is not set
-# CONFIG_HP100 is not set
-# CONFIG_NET_PCI is not set
-CONFIG_FS_ENET=y
-# CONFIG_FS_ENET_HAS_SCC is not set
-CONFIG_FS_ENET_HAS_FCC=y
-
-#
-# Ethernet (1000 Mbit)
-#
-# CONFIG_ACENIC is not set
-# CONFIG_DL2K is not set
-# CONFIG_E1000 is not set
-# CONFIG_NS83820 is not set
-# CONFIG_HAMACHI is not set
-# CONFIG_YELLOWFIN is not set
-# CONFIG_R8169 is not set
-# CONFIG_SIS190 is not set
-# CONFIG_SKGE is not set
-# CONFIG_SKY2 is not set
-# CONFIG_SK98LIN is not set
-# CONFIG_TIGON3 is not set
-# CONFIG_BNX2 is not set
-# CONFIG_QLA3XXX is not set
-# CONFIG_ATL1 is not set
-
-#
-# Ethernet (10000 Mbit)
-#
-# CONFIG_CHELSIO_T1 is not set
-# CONFIG_CHELSIO_T3 is not set
-# CONFIG_IXGB is not set
-# CONFIG_S2IO is not set
-# CONFIG_MYRI10GE is not set
-# CONFIG_NETXEN_NIC is not set
-
-#
-# Token Ring devices
-#
-# CONFIG_TR is not set
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
-#
-# CONFIG_WAN is not set
-# CONFIG_FDDI is not set
-# CONFIG_HIPPI is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
-# CONFIG_NETCONSOLE is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-
-#
-# ISDN subsystem
-#
-# CONFIG_ISDN is not set
-
-#
-# Telephony Support
-#
-# CONFIG_PHONE is not set
-
-#
-# Input device support
-#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-
-#
-# Userland interfaces
-#
-# CONFIG_INPUT_MOUSEDEV is not set
-# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
-# CONFIG_INPUT_EVDEV is not set
-# CONFIG_INPUT_EVBUG is not set
-
-#
-# Input Device Drivers
-#
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
-# CONFIG_INPUT_MISC is not set
-
-#
-# Hardware I/O ports
-#
-# CONFIG_SERIO is not set
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-# CONFIG_VT is not set
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-# CONFIG_SERIAL_8250 is not set
-
-#
-# Non-8250 serial port support
-#
-# CONFIG_SERIAL_UARTLITE is not set
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_SERIAL_CPM=y
-CONFIG_SERIAL_CPM_CONSOLE=y
-CONFIG_SERIAL_CPM_SCC1=y
-# CONFIG_SERIAL_CPM_SCC2 is not set
-# CONFIG_SERIAL_CPM_SCC3 is not set
-CONFIG_SERIAL_CPM_SCC4=y
-# CONFIG_SERIAL_CPM_SMC1 is not set
-# CONFIG_SERIAL_CPM_SMC2 is not set
-# CONFIG_SERIAL_JSM is not set
-CONFIG_UNIX98_PTYS=y
-CONFIG_LEGACY_PTYS=y
-CONFIG_LEGACY_PTY_COUNT=256
-
-#
-# IPMI
-#
-# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
-# CONFIG_WATCHDOG is not set
-CONFIG_HW_RANDOM=y
-# CONFIG_NVRAM is not set
-CONFIG_GEN_RTC=y
-# CONFIG_GEN_RTC_X is not set
-# CONFIG_DTLK is not set
-# CONFIG_R3964 is not set
-# CONFIG_APPLICOM is not set
-# CONFIG_AGP is not set
-# CONFIG_DRM is not set
-# CONFIG_RAW_DRIVER is not set
-
-#
-# TPM devices
-#
-# CONFIG_TCG_TPM is not set
-
-#
-# I2C support
-#
-# CONFIG_I2C is not set
-
-#
-# SPI support
-#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-
-#
-# Dallas's 1-wire bus
-#
-# CONFIG_W1 is not set
-
-#
-# Hardware Monitoring support
-#
-CONFIG_HWMON=y
-# CONFIG_HWMON_VID is not set
-# CONFIG_SENSORS_ABITUGURU is not set
-# CONFIG_SENSORS_F71805F is not set
-# CONFIG_SENSORS_PC87427 is not set
-# CONFIG_SENSORS_VT1211 is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
-
-#
-# Multifunction device drivers
-#
-# CONFIG_MFD_SM501 is not set
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-
-#
-# Digital Video Broadcasting Devices
-#
-# CONFIG_DVB is not set
-
-#
-# Graphics support
-#
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-# CONFIG_FB is not set
-# CONFIG_FB_IBM_GXT4500 is not set
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-
-#
-# HID Devices
-#
-CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
-
-#
-# USB support
-#
-CONFIG_USB_ARCH_HAS_HCD=y
-CONFIG_USB_ARCH_HAS_OHCI=y
-CONFIG_USB_ARCH_HAS_EHCI=y
-# CONFIG_USB is not set
-
-#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
-#
-
-#
-# USB Gadget Support
-#
-# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
-# CONFIG_MMC is not set
-
-#
-# LED devices
-#
-# CONFIG_NEW_LEDS is not set
-
-#
-# LED drivers
-#
-
-#
-# LED Triggers
-#
-
-#
-# InfiniBand support
-#
-# CONFIG_INFINIBAND is not set
-
-#
-# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
-#
-
-#
-# Real Time Clock
-#
-# CONFIG_RTC_CLASS is not set
-
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
-
-#
-# Auxiliary Display support
-#
-
-#
-# Virtualization
-#
-
-#
-# File systems
-#
-CONFIG_EXT2_FS=y
-# CONFIG_EXT2_FS_XATTR is not set
-# CONFIG_EXT2_FS_XIP is not set
-CONFIG_EXT3_FS=y
-CONFIG_EXT3_FS_XATTR=y
-# CONFIG_EXT3_FS_POSIX_ACL is not set
-# CONFIG_EXT3_FS_SECURITY is not set
-# CONFIG_EXT4DEV_FS is not set
-CONFIG_JBD=y
-# CONFIG_JBD_DEBUG is not set
-CONFIG_FS_MBCACHE=y
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-CONFIG_FS_POSIX_ACL=y
-# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-CONFIG_INOTIFY=y
-CONFIG_INOTIFY_USER=y
-# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-# CONFIG_FUSE_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_KCORE=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_SYSFS=y
-CONFIG_TMPFS=y
-# CONFIG_TMPFS_POSIX_ACL is not set
-# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
-# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-# CONFIG_NFS_DIRECTIO is not set
-# CONFIG_NFSD is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_LOCKD_V4=y
-CONFIG_NFS_ACL_SUPPORT=y
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-CONFIG_SUNRPC_GSS=y
-CONFIG_RPCSEC_GSS_KRB5=y
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-# CONFIG_9P_FS is not set
-
-#
-# Partition Types
-#
-CONFIG_PARTITION_ADVANCED=y
-# CONFIG_ACORN_PARTITION is not set
-# CONFIG_OSF_PARTITION is not set
-# CONFIG_AMIGA_PARTITION is not set
-# CONFIG_ATARI_PARTITION is not set
-# CONFIG_MAC_PARTITION is not set
-# CONFIG_MSDOS_PARTITION is not set
-# CONFIG_LDM_PARTITION is not set
-# CONFIG_SGI_PARTITION is not set
-# CONFIG_ULTRIX_PARTITION is not set
-# CONFIG_SUN_PARTITION is not set
-# CONFIG_KARMA_PARTITION is not set
-# CONFIG_EFI_PARTITION is not set
-
-#
-# Native Language Support
-#
-# CONFIG_NLS is not set
-
-#
-# Distributed Lock Manager
-#
-# CONFIG_DLM is not set
-# CONFIG_SCC_ENET is not set
-# CONFIG_FEC_ENET is not set
-
-#
-# CPM2 Options
-#
-
-#
-# Library routines
-#
-# CONFIG_CRC_CCITT is not set
-# CONFIG_CRC16 is not set
-# CONFIG_CRC32 is not set
-# CONFIG_LIBCRC32C is not set
-CONFIG_PLIST=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-# CONFIG_PROFILING is not set
-
-#
-# Kernel hacking
-#
-# CONFIG_PRINTK_TIME is not set
-CONFIG_ENABLE_MUST_CHECK=y
-# CONFIG_MAGIC_SYSRQ is not set
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_HEADERS_CHECK is not set
-# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_DEBUG_BUGVERBOSE is not set
-# CONFIG_KGDB_CONSOLE is not set
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-
-#
-# Cryptographic options
-#
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_BLKCIPHER=y
-CONFIG_CRYPTO_MANAGER=y
-# CONFIG_CRYPTO_HMAC is not set
-# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
-# CONFIG_CRYPTO_MD4 is not set
-CONFIG_CRYPTO_MD5=y
-# CONFIG_CRYPTO_SHA1 is not set
-# CONFIG_CRYPTO_SHA256 is not set
-# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
-# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-CONFIG_CRYPTO_ECB=y
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_PCBC=y
-# CONFIG_CRYPTO_LRW is not set
-CONFIG_CRYPTO_DES=y
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
-# CONFIG_CRYPTO_AES is not set
-# CONFIG_CRYPTO_CAST5 is not set
-# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
-# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-
-#
-# Hardware crypto devices
-#
diff --git a/arch/ppc/configs/mpc86x_ads_defconfig b/arch/ppc/configs/mpc86x_ads_defconfig
deleted file mode 100644
index f63c6f5..0000000
--- a/arch/ppc/configs/mpc86x_ads_defconfig
+++ /dev/null
@@ -1,633 +0,0 @@
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.12-rc4
-# Tue Jun 14 13:36:35 2005
-#
-CONFIG_MMU=y
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_HAVE_DEC_LOCK=y
-CONFIG_PPC=y
-CONFIG_PPC32=y
-CONFIG_GENERIC_NVRAM=y
-CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
-
-#
-# Code maturity level options
-#
-CONFIG_EXPERIMENTAL=y
-# CONFIG_CLEAN_COMPILE is not set
-CONFIG_BROKEN=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-
-#
-# General setup
-#
-CONFIG_LOCALVERSION=""
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-CONFIG_SYSCTL=y
-# CONFIG_AUDIT is not set
-# CONFIG_HOTPLUG is not set
-CONFIG_KOBJECT_UEVENT=y
-# CONFIG_IKCONFIG is not set
-CONFIG_EMBEDDED=y
-# CONFIG_KALLSYMS is not set
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-# CONFIG_BASE_FULL is not set
-CONFIG_FUTEX=y
-# CONFIG_EPOLL is not set
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-# CONFIG_SHMEM is not set
-CONFIG_CC_ALIGN_FUNCTIONS=0
-CONFIG_CC_ALIGN_LABELS=0
-CONFIG_CC_ALIGN_LOOPS=0
-CONFIG_CC_ALIGN_JUMPS=0
-CONFIG_TINY_SHMEM=y
-CONFIG_BASE_SMALL=1
-
-#
-# Loadable module support
-#
-CONFIG_MODULES=y
-# CONFIG_MODULE_UNLOAD is not set
-CONFIG_OBSOLETE_MODPARM=y
-# CONFIG_MODVERSIONS is not set
-# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
-
-#
-# Processor
-#
-# CONFIG_6xx is not set
-# CONFIG_40x is not set
-# CONFIG_44x is not set
-# CONFIG_POWER3 is not set
-# CONFIG_POWER4 is not set
-CONFIG_8xx=y
-# CONFIG_E500 is not set
-# CONFIG_MATH_EMULATION is not set
-# CONFIG_CPU_FREQ is not set
-CONFIG_EMBEDDEDBOOT=y
-# CONFIG_PM is not set
-CONFIG_NOT_COHERENT_CACHE=y
-
-#
-# Platform options
-#
-CONFIG_FADS=y
-# CONFIG_RPXLITE is not set
-# CONFIG_RPXCLASSIC is not set
-# CONFIG_BSEIP is not set
-# CONFIG_MPC8XXFADS is not set
-CONFIG_MPC86XADS=y
-# CONFIG_TQM823L is not set
-# CONFIG_TQM850L is not set
-# CONFIG_TQM855L is not set
-# CONFIG_TQM860L is not set
-# CONFIG_FPS850L is not set
-# CONFIG_SPD823TS is not set
-# CONFIG_IVMS8 is not set
-# CONFIG_IVML24 is not set
-# CONFIG_SM850 is not set
-# CONFIG_HERMES_PRO is not set
-# CONFIG_IP860 is not set
-# CONFIG_LWMON is not set
-# CONFIG_PCU_E is not set
-# CONFIG_CCM is not set
-# CONFIG_LANTEC is not set
-# CONFIG_MBX is not set
-# CONFIG_WINCEPT is not set
-# CONFIG_SMP is not set
-# CONFIG_PREEMPT is not set
-# CONFIG_HIGHMEM is not set
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_MISC is not set
-# CONFIG_CMDLINE_BOOL is not set
-CONFIG_ISA_DMA_API=y
-
-#
-# Bus options
-#
-# CONFIG_PCI is not set
-# CONFIG_PCI_DOMAINS is not set
-# CONFIG_PCI_QSPAN is not set
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
-# CONFIG_PCCARD is not set
-
-#
-# Advanced setup
-#
-# CONFIG_ADVANCED_OPTIONS is not set
-
-#
-# Default settings for advanced configuration options are used
-#
-CONFIG_HIGHMEM_START=0xfe000000
-CONFIG_LOWMEM_SIZE=0x30000000
-CONFIG_KERNEL_START=0xc0000000
-CONFIG_TASK_SIZE=0x80000000
-CONFIG_CONSISTENT_START=0xff100000
-CONFIG_CONSISTENT_SIZE=0x00200000
-CONFIG_BOOT_LOAD=0x00400000
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-# CONFIG_STANDALONE is not set
-CONFIG_PREVENT_FIRMWARE_BUILD=y
-# CONFIG_FW_LOADER is not set
-
-#
-# Memory Technology Devices (MTD)
-#
-# CONFIG_MTD is not set
-
-#
-# Parallel port support
-#
-# CONFIG_PARPORT is not set
-
-#
-# Plug and Play support
-#
-
-#
-# Block devices
-#
-# CONFIG_BLK_DEV_FD is not set
-# CONFIG_BLK_DEV_COW_COMMON is not set
-CONFIG_BLK_DEV_LOOP=y
-# CONFIG_BLK_DEV_CRYPTOLOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
-# CONFIG_BLK_DEV_RAM is not set
-CONFIG_BLK_DEV_RAM_COUNT=16
-CONFIG_INITRAMFS_SOURCE=""
-# CONFIG_LBD is not set
-# CONFIG_CDROM_PKTCDVD is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-# CONFIG_ATA_OVER_ETH is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_SCSI is not set
-
-#
-# Multi-device support (RAID and LVM)
-#
-# CONFIG_MD is not set
-
-#
-# Fusion MPT device support
-#
-
-#
-# IEEE 1394 (FireWire) support
-#
-# CONFIG_IEEE1394 is not set
-
-#
-# I2O device support
-#
-
-#
-# Macintosh device drivers
-#
-
-#
-# Networking support
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_IP_PNP_BOOTP is not set
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_TUNNEL is not set
-CONFIG_IP_TCPDIAG=y
-# CONFIG_IP_TCPDIAG_IPV6 is not set
-CONFIG_IPV6=m
-# CONFIG_IPV6_PRIVACY is not set
-# CONFIG_INET6_AH is not set
-# CONFIG_INET6_ESP is not set
-# CONFIG_INET6_IPCOMP is not set
-# CONFIG_INET6_TUNNEL is not set
-# CONFIG_IPV6_TUNNEL is not set
-# CONFIG_NETFILTER is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_SCTP is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
-# CONFIG_NET_SCHED is not set
-# CONFIG_NET_CLS_ROUTE is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-CONFIG_NETDEVICES=y
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-
-#
-# Ethernet (10 or 100Mbit)
-#
-CONFIG_NET_ETHERNET=y
-# CONFIG_MII is not set
-# CONFIG_OAKNET is not set
-
-#
-# Ethernet (1000 Mbit)
-#
-
-#
-# Ethernet (10000 Mbit)
-#
-
-#
-# Token Ring devices
-#
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
-#
-# CONFIG_WAN is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
-# CONFIG_NETCONSOLE is not set
-
-#
-# ISDN subsystem
-#
-# CONFIG_ISDN is not set
-
-#
-# Telephony Support
-#
-# CONFIG_PHONE is not set
-
-#
-# Input device support
-#
-# CONFIG_INPUT is not set
-
-#
-# Hardware I/O ports
-#
-# CONFIG_SERIO is not set
-# CONFIG_GAMEPORT is not set
-CONFIG_SOUND_GAMEPORT=y
-
-#
-# Character devices
-#
-# CONFIG_VT is not set
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-# CONFIG_SERIAL_8250 is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_SERIAL_CPM=y
-CONFIG_SERIAL_CPM_CONSOLE=y
-# CONFIG_SERIAL_CPM_SCC1 is not set
-# CONFIG_SERIAL_CPM_SCC2 is not set
-# CONFIG_SERIAL_CPM_SCC3 is not set
-# CONFIG_SERIAL_CPM_SCC4 is not set
-CONFIG_SERIAL_CPM_SMC1=y
-# CONFIG_SERIAL_CPM_SMC2 is not set
-CONFIG_UNIX98_PTYS=y
-# CONFIG_LEGACY_PTYS is not set
-
-#
-# IPMI
-#
-# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
-# CONFIG_WATCHDOG is not set
-# CONFIG_NVRAM is not set
-# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
-# CONFIG_R3964 is not set
-
-#
-# Ftape, the floppy tape device driver
-#
-# CONFIG_AGP is not set
-# CONFIG_DRM is not set
-# CONFIG_RAW_DRIVER is not set
-
-#
-# TPM devices
-#
-
-#
-# I2C support
-#
-# CONFIG_I2C is not set
-
-#
-# Dallas's 1-wire bus
-#
-# CONFIG_W1 is not set
-
-#
-# Misc devices
-#
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-
-#
-# Digital Video Broadcasting Devices
-#
-# CONFIG_DVB is not set
-
-#
-# Graphics support
-#
-# CONFIG_FB is not set
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-
-#
-# USB support
-#
-# CONFIG_USB_ARCH_HAS_HCD is not set
-# CONFIG_USB_ARCH_HAS_OHCI is not set
-
-#
-# USB Gadget Support
-#
-# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
-# CONFIG_MMC is not set
-
-#
-# InfiniBand support
-#
-# CONFIG_INFINIBAND is not set
-
-#
-# File systems
-#
-# CONFIG_EXT2_FS is not set
-CONFIG_EXT3_FS=y
-# CONFIG_EXT3_FS_XATTR is not set
-CONFIG_JBD=y
-# CONFIG_JBD_DEBUG is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-
-#
-# XFS support
-#
-# CONFIG_XFS_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_QUOTA is not set
-# CONFIG_DNOTIFY is not set
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_KCORE=y
-CONFIG_SYSFS=y
-# CONFIG_DEVFS_FS is not set
-# CONFIG_DEVPTS_FS_XATTR is not set
-# CONFIG_TMPFS is not set
-# CONFIG_HUGETLBFS is not set
-# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V4=y
-# CONFIG_NFS_DIRECTIO is not set
-# CONFIG_NFSD is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_LOCKD_V4=y
-CONFIG_SUNRPC=y
-CONFIG_SUNRPC_GSS=y
-CONFIG_RPCSEC_GSS_KRB5=y
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
-# CONFIG_NLS is not set
-
-#
-# MPC8xx CPM Options
-#
-CONFIG_SCC_ENET=y
-CONFIG_SCC1_ENET=y
-# CONFIG_SCC2_ENET is not set
-# CONFIG_SCC3_ENET is not set
-# CONFIG_FEC_ENET is not set
-# CONFIG_ENET_BIG_BUFFERS is not set
-
-#
-# Generic MPC8xx Options
-#
-# CONFIG_8xx_COPYBACK is not set
-# CONFIG_8xx_CPU6 is not set
-CONFIG_NO_UCODE_PATCH=y
-# CONFIG_USB_SOF_UCODE_PATCH is not set
-# CONFIG_I2C_SPI_UCODE_PATCH is not set
-# CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set
-
-#
-# Library routines
-#
-# CONFIG_CRC_CCITT is not set
-# CONFIG_CRC32 is not set
-# CONFIG_LIBCRC32C is not set
-
-#
-# Profiling support
-#
-# CONFIG_PROFILING is not set
-
-#
-# Kernel hacking
-#
-# CONFIG_PRINTK_TIME is not set
-# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-
-#
-# Cryptographic options
-#
-CONFIG_CRYPTO=y
-# CONFIG_CRYPTO_HMAC is not set
-# CONFIG_CRYPTO_NULL is not set
-# CONFIG_CRYPTO_MD4 is not set
-CONFIG_CRYPTO_MD5=y
-# CONFIG_CRYPTO_SHA1 is not set
-# CONFIG_CRYPTO_SHA256 is not set
-# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
-# CONFIG_CRYPTO_TGR192 is not set
-CONFIG_CRYPTO_DES=y
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
-# CONFIG_CRYPTO_AES is not set
-# CONFIG_CRYPTO_CAST5 is not set
-# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
-# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_TEST is not set
-
-#
-# Hardware crypto devices
-#
diff --git a/arch/ppc/configs/mpc885ads_defconfig b/arch/ppc/configs/mpc885ads_defconfig
deleted file mode 100644
index 016f94d..0000000
--- a/arch/ppc/configs/mpc885ads_defconfig
+++ /dev/null
@@ -1,622 +0,0 @@
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.12-rc6
-# Thu Jun 9 21:17:29 2005
-#
-CONFIG_MMU=y
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_HAVE_DEC_LOCK=y
-CONFIG_PPC=y
-CONFIG_PPC32=y
-CONFIG_GENERIC_NVRAM=y
-CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
-
-#
-# Code maturity level options
-#
-CONFIG_EXPERIMENTAL=y
-# CONFIG_CLEAN_COMPILE is not set
-CONFIG_BROKEN=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-
-#
-# General setup
-#
-CONFIG_LOCALVERSION=""
-# CONFIG_SWAP is not set
-CONFIG_SYSVIPC=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-CONFIG_SYSCTL=y
-# CONFIG_AUDIT is not set
-CONFIG_HOTPLUG=y
-CONFIG_KOBJECT_UEVENT=y
-# CONFIG_IKCONFIG is not set
-CONFIG_EMBEDDED=y
-# CONFIG_KALLSYMS is not set
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-# CONFIG_EPOLL is not set
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_SHMEM=y
-CONFIG_CC_ALIGN_FUNCTIONS=0
-CONFIG_CC_ALIGN_LABELS=0
-CONFIG_CC_ALIGN_LOOPS=0
-CONFIG_CC_ALIGN_JUMPS=0
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-
-#
-# Loadable module support
-#
-# CONFIG_MODULES is not set
-
-#
-# Processor
-#
-# CONFIG_6xx is not set
-# CONFIG_40x is not set
-# CONFIG_44x is not set
-# CONFIG_POWER3 is not set
-# CONFIG_POWER4 is not set
-CONFIG_8xx=y
-# CONFIG_E500 is not set
-# CONFIG_MATH_EMULATION is not set
-# CONFIG_CPU_FREQ is not set
-CONFIG_EMBEDDEDBOOT=y
-# CONFIG_PM is not set
-CONFIG_NOT_COHERENT_CACHE=y
-
-#
-# Platform options
-#
-# CONFIG_RPXLITE is not set
-# CONFIG_RPXCLASSIC is not set
-# CONFIG_BSEIP is not set
-# CONFIG_FADS is not set
-CONFIG_MPC885ADS=y
-# CONFIG_TQM823L is not set
-# CONFIG_TQM850L is not set
-# CONFIG_TQM855L is not set
-# CONFIG_TQM860L is not set
-# CONFIG_FPS850L is not set
-# CONFIG_SPD823TS is not set
-# CONFIG_IVMS8 is not set
-# CONFIG_IVML24 is not set
-# CONFIG_SM850 is not set
-# CONFIG_HERMES_PRO is not set
-# CONFIG_IP860 is not set
-# CONFIG_LWMON is not set
-# CONFIG_PCU_E is not set
-# CONFIG_CCM is not set
-# CONFIG_LANTEC is not set
-# CONFIG_MBX is not set
-# CONFIG_WINCEPT is not set
-# CONFIG_SMP is not set
-# CONFIG_PREEMPT is not set
-# CONFIG_HIGHMEM is not set
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_MISC is not set
-# CONFIG_CMDLINE_BOOL is not set
-CONFIG_ISA_DMA_API=y
-
-#
-# Bus options
-#
-# CONFIG_PCI is not set
-# CONFIG_PCI_DOMAINS is not set
-# CONFIG_PCI_QSPAN is not set
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
-# CONFIG_PCCARD is not set
-
-#
-# Advanced setup
-#
-# CONFIG_ADVANCED_OPTIONS is not set
-
-#
-# Default settings for advanced configuration options are used
-#
-CONFIG_HIGHMEM_START=0xfe000000
-CONFIG_LOWMEM_SIZE=0x30000000
-CONFIG_KERNEL_START=0xc0000000
-CONFIG_TASK_SIZE=0x80000000
-CONFIG_CONSISTENT_START=0xff100000
-CONFIG_CONSISTENT_SIZE=0x00200000
-CONFIG_BOOT_LOAD=0x00400000
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_STANDALONE=y
-CONFIG_PREVENT_FIRMWARE_BUILD=y
-# CONFIG_FW_LOADER is not set
-
-#
-# Memory Technology Devices (MTD)
-#
-# CONFIG_MTD is not set
-
-#
-# Parallel port support
-#
-# CONFIG_PARPORT is not set
-
-#
-# Plug and Play support
-#
-
-#
-# Block devices
-#
-# CONFIG_BLK_DEV_FD is not set
-# CONFIG_BLK_DEV_COW_COMMON is not set
-# CONFIG_BLK_DEV_LOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
-# CONFIG_BLK_DEV_RAM is not set
-CONFIG_BLK_DEV_RAM_COUNT=16
-CONFIG_INITRAMFS_SOURCE=""
-# CONFIG_LBD is not set
-# CONFIG_CDROM_PKTCDVD is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-# CONFIG_IOSCHED_AS is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-# CONFIG_ATA_OVER_ETH is not set
-
-#
-# ATA/ATAPI/MFM/RLL support
-#
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_SCSI is not set
-
-#
-# Multi-device support (RAID and LVM)
-#
-# CONFIG_MD is not set
-
-#
-# Fusion MPT device support
-#
-
-#
-# IEEE 1394 (FireWire) support
-#
-# CONFIG_IEEE1394 is not set
-
-#
-# I2O device support
-#
-
-#
-# Macintosh device drivers
-#
-
-#
-# Networking support
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_TUNNEL is not set
-CONFIG_IP_TCPDIAG=y
-# CONFIG_IP_TCPDIAG_IPV6 is not set
-# CONFIG_IPV6 is not set
-# CONFIG_NETFILTER is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_SCTP is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
-# CONFIG_NET_SCHED is not set
-# CONFIG_NET_CLS_ROUTE is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-CONFIG_NETDEVICES=y
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-
-#
-# Ethernet (10 or 100Mbit)
-#
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-# CONFIG_OAKNET is not set
-
-#
-# Ethernet (1000 Mbit)
-#
-
-#
-# Ethernet (10000 Mbit)
-#
-
-#
-# Token Ring devices
-#
-
-#
-# Wireless LAN (non-hamradio)
-#
-# CONFIG_NET_RADIO is not set
-
-#
-# Wan interfaces
-#
-# CONFIG_WAN is not set
-CONFIG_PPP=y
-# CONFIG_PPP_MULTILINK is not set
-# CONFIG_PPP_FILTER is not set
-CONFIG_PPP_ASYNC=y
-CONFIG_PPP_SYNC_TTY=y
-CONFIG_PPP_DEFLATE=y
-# CONFIG_PPP_BSDCOMP is not set
-# CONFIG_PPPOE is not set
-# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
-# CONFIG_NETCONSOLE is not set
-
-#
-# ISDN subsystem
-#
-# CONFIG_ISDN is not set
-
-#
-# Telephony Support
-#
-# CONFIG_PHONE is not set
-
-#
-# Input device support
-#
-# CONFIG_INPUT is not set
-
-#
-# Hardware I/O ports
-#
-# CONFIG_SERIO is not set
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-# CONFIG_VT is not set
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-# CONFIG_SERIAL_8250 is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_SERIAL_CPM=y
-CONFIG_SERIAL_CPM_CONSOLE=y
-# CONFIG_SERIAL_CPM_SCC1 is not set
-# CONFIG_SERIAL_CPM_SCC2 is not set
-# CONFIG_SERIAL_CPM_SCC3 is not set
-# CONFIG_SERIAL_CPM_SCC4 is not set
-CONFIG_SERIAL_CPM_SMC1=y
-CONFIG_SERIAL_CPM_SMC2=y
-CONFIG_UNIX98_PTYS=y
-# CONFIG_LEGACY_PTYS is not set
-
-#
-# IPMI
-#
-# CONFIG_IPMI_HANDLER is not set
-
-#
-# Watchdog Cards
-#
-# CONFIG_WATCHDOG is not set
-# CONFIG_NVRAM is not set
-# CONFIG_GEN_RTC is not set
-# CONFIG_DTLK is not set
-# CONFIG_R3964 is not set
-
-#
-# Ftape, the floppy tape device driver
-#
-# CONFIG_AGP is not set
-# CONFIG_DRM is not set
-# CONFIG_RAW_DRIVER is not set
-
-#
-# TPM devices
-#
-
-#
-# I2C support
-#
-# CONFIG_I2C is not set
-
-#
-# Dallas's 1-wire bus
-#
-# CONFIG_W1 is not set
-
-#
-# Misc devices
-#
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-
-#
-# Digital Video Broadcasting Devices
-#
-# CONFIG_DVB is not set
-
-#
-# Graphics support
-#
-# CONFIG_FB is not set
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-
-#
-# USB support
-#
-# CONFIG_USB_ARCH_HAS_HCD is not set
-# CONFIG_USB_ARCH_HAS_OHCI is not set
-
-#
-# USB Gadget Support
-#
-# CONFIG_USB_GADGET is not set
-
-#
-# MMC/SD Card support
-#
-# CONFIG_MMC is not set
-
-#
-# InfiniBand support
-#
-# CONFIG_INFINIBAND is not set
-
-#
-# File systems
-#
-CONFIG_EXT2_FS=y
-CONFIG_EXT2_FS_XATTR=y
-# CONFIG_EXT2_FS_POSIX_ACL is not set
-# CONFIG_EXT2_FS_SECURITY is not set
-CONFIG_EXT3_FS=y
-CONFIG_EXT3_FS_XATTR=y
-# CONFIG_EXT3_FS_POSIX_ACL is not set
-# CONFIG_EXT3_FS_SECURITY is not set
-CONFIG_JBD=y
-# CONFIG_JBD_DEBUG is not set
-CONFIG_FS_MBCACHE=y
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-
-#
-# XFS support
-#
-# CONFIG_XFS_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_QUOTA is not set
-# CONFIG_DNOTIFY is not set
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-# CONFIG_PROC_KCORE is not set
-CONFIG_SYSFS=y
-# CONFIG_DEVFS_FS is not set
-# CONFIG_DEVPTS_FS_XATTR is not set
-# CONFIG_TMPFS is not set
-# CONFIG_HUGETLBFS is not set
-# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
-CONFIG_NFS_FS=y
-# CONFIG_NFS_V3 is not set
-# CONFIG_NFS_V4 is not set
-# CONFIG_NFS_DIRECTIO is not set
-# CONFIG_NFSD is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_SUNRPC=y
-# CONFIG_RPCSEC_GSS_KRB5 is not set
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-
-#
-# Partition Types
-#
-CONFIG_PARTITION_ADVANCED=y
-# CONFIG_ACORN_PARTITION is not set
-# CONFIG_OSF_PARTITION is not set
-# CONFIG_AMIGA_PARTITION is not set
-# CONFIG_ATARI_PARTITION is not set
-# CONFIG_MAC_PARTITION is not set
-CONFIG_MSDOS_PARTITION=y
-# CONFIG_BSD_DISKLABEL is not set
-# CONFIG_MINIX_SUBPARTITION is not set
-# CONFIG_SOLARIS_X86_PARTITION is not set
-# CONFIG_UNIXWARE_DISKLABEL is not set
-# CONFIG_LDM_PARTITION is not set
-# CONFIG_SGI_PARTITION is not set
-# CONFIG_ULTRIX_PARTITION is not set
-# CONFIG_SUN_PARTITION is not set
-# CONFIG_EFI_PARTITION is not set
-
-#
-# Native Language Support
-#
-# CONFIG_NLS is not set
-
-#
-# MPC8xx CPM Options
-#
-CONFIG_SCC_ENET=y
-# CONFIG_SCC1_ENET is not set
-# CONFIG_SCC2_ENET is not set
-CONFIG_SCC3_ENET=y
-# CONFIG_FEC_ENET is not set
-# CONFIG_ENET_BIG_BUFFERS is not set
-
-#
-# Generic MPC8xx Options
-#
-CONFIG_8xx_COPYBACK=y
-CONFIG_8xx_CPU6=y
-CONFIG_NO_UCODE_PATCH=y
-# CONFIG_USB_SOF_UCODE_PATCH is not set
-# CONFIG_I2C_SPI_UCODE_PATCH is not set
-# CONFIG_I2C_SPI_SMC1_UCODE_PATCH is not set
-
-#
-# Library routines
-#
-CONFIG_CRC_CCITT=y
-# CONFIG_CRC32 is not set
-# CONFIG_LIBCRC32C is not set
-CONFIG_ZLIB_INFLATE=y
-CONFIG_ZLIB_DEFLATE=y
-
-#
-# Profiling support
-#
-# CONFIG_PROFILING is not set
-
-#
-# Kernel hacking
-#
-# CONFIG_PRINTK_TIME is not set
-# CONFIG_DEBUG_KERNEL is not set
-CONFIG_LOG_BUF_SHIFT=14
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-
-#
-# Cryptographic options
-#
-# CONFIG_CRYPTO is not set
-
-#
-# Hardware crypto devices
-#
diff --git a/arch/ppc/platforms/Makefile b/arch/ppc/platforms/Makefile
index 40f53fb..6260231 100644
--- a/arch/ppc/platforms/Makefile
+++ b/arch/ppc/platforms/Makefile
@@ -4,7 +4,6 @@
obj-$(CONFIG_PPC_PREP) += prep_pci.o prep_setup.o
obj-$(CONFIG_PREP_RESIDUAL) += residual.o
-obj-$(CONFIG_PQ2ADS) += pq2ads.o
obj-$(CONFIG_TQM8260) += tqm8260_setup.o
obj-$(CONFIG_CPCI690) += cpci690.o
obj-$(CONFIG_EV64260) += ev64260.o
@@ -24,6 +23,3 @@
obj-$(CONFIG_SPRUCE) += spruce.o
obj-$(CONFIG_LITE5200) += lite5200.o
obj-$(CONFIG_EV64360) += ev64360.o
-obj-$(CONFIG_MPC86XADS) += mpc866ads_setup.o
-obj-$(CONFIG_MPC885ADS) += mpc885ads_setup.o
-obj-$(CONFIG_ADS8272) += mpc8272ads_setup.o
diff --git a/arch/ppc/platforms/fads.h b/arch/ppc/platforms/fads.h
index 2f9f0f6..5219366 100644
--- a/arch/ppc/platforms/fads.h
+++ b/arch/ppc/platforms/fads.h
@@ -22,29 +22,6 @@
#include <asm/ppcboot.h>
-#if defined(CONFIG_MPC86XADS)
-
-#define BOARD_CHIP_NAME "MPC86X"
-
-/* U-Boot maps BCSR to 0xff080000 */
-#define BCSR_ADDR ((uint)0xff080000)
-
-/* MPC86XADS has one more CPLD and an additional BCSR.
- */
-#define CFG_PHYDEV_ADDR ((uint)0xff0a0000)
-#define BCSR5 ((uint)(CFG_PHYDEV_ADDR + 0x300))
-
-#define BCSR5_T1_RST 0x10
-#define BCSR5_ATM155_RST 0x08
-#define BCSR5_ATM25_RST 0x04
-#define BCSR5_MII1_EN 0x02
-#define BCSR5_MII1_RST 0x01
-
-/* There is no PHY link change interrupt */
-#define PHY_INTERRUPT (-1)
-
-#else /* FADS */
-
/* Memory map is configured by the PROM startup.
* I tried to follow the FADS manual, although the startup PROM
* dictates this and we simply have to move some of the physical
@@ -55,8 +32,6 @@
/* PHY link change interrupt */
#define PHY_INTERRUPT SIU_IRQ2
-#endif /* CONFIG_MPC86XADS */
-
#define BCSR_SIZE ((uint)(64 * 1024))
#define BCSR0 ((uint)(BCSR_ADDR + 0x00))
#define BCSR1 ((uint)(BCSR_ADDR + 0x04))
diff --git a/arch/ppc/platforms/mpc8272ads_setup.c b/arch/ppc/platforms/mpc8272ads_setup.c
deleted file mode 100644
index 47f4b38..0000000
--- a/arch/ppc/platforms/mpc8272ads_setup.c
+++ /dev/null
@@ -1,367 +0,0 @@
-/*
- * arch/ppc/platforms/mpc8272ads_setup.c
- *
- * MPC82xx Board-specific PlatformDevice descriptions
- *
- * 2005 (c) MontaVista Software, Inc.
- * Vitaly Bordug <vbordug@ru.mvista.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/device.h>
-#include <linux/ioport.h>
-#include <linux/fs_enet_pd.h>
-#include <linux/platform_device.h>
-#include <linux/phy.h>
-
-#include <asm/io.h>
-#include <asm/mpc8260.h>
-#include <asm/cpm2.h>
-#include <asm/immap_cpm2.h>
-#include <asm/irq.h>
-#include <asm/ppc_sys.h>
-#include <asm/ppcboot.h>
-#include <linux/fs_uart_pd.h>
-
-#include "pq2ads_pd.h"
-
-static void init_fcc1_ioports(struct fs_platform_info*);
-static void init_fcc2_ioports(struct fs_platform_info*);
-static void init_scc1_uart_ioports(struct fs_uart_platform_info*);
-static void init_scc4_uart_ioports(struct fs_uart_platform_info*);
-
-static struct fs_uart_platform_info mpc8272_uart_pdata[] = {
- [fsid_scc1_uart] = {
- .init_ioports = init_scc1_uart_ioports,
- .fs_no = fsid_scc1_uart,
- .brg = 1,
- .tx_num_fifo = 4,
- .tx_buf_size = 32,
- .rx_num_fifo = 4,
- .rx_buf_size = 32,
- },
- [fsid_scc4_uart] = {
- .init_ioports = init_scc4_uart_ioports,
- .fs_no = fsid_scc4_uart,
- .brg = 4,
- .tx_num_fifo = 4,
- .tx_buf_size = 32,
- .rx_num_fifo = 4,
- .rx_buf_size = 32,
- },
-};
-
-static struct fs_mii_bb_platform_info m82xx_mii_bb_pdata = {
- .mdio_dat.bit = 18,
- .mdio_dir.bit = 18,
- .mdc_dat.bit = 19,
- .delay = 1,
-};
-
-static struct fs_platform_info mpc82xx_enet_pdata[] = {
- [fsid_fcc1] = {
- .fs_no = fsid_fcc1,
- .cp_page = CPM_CR_FCC1_PAGE,
- .cp_block = CPM_CR_FCC1_SBLOCK,
-
- .clk_trx = (PC_F1RXCLK | PC_F1TXCLK),
- .clk_route = CMX1_CLK_ROUTE,
- .clk_mask = CMX1_CLK_MASK,
- .init_ioports = init_fcc1_ioports,
-
- .mem_offset = FCC1_MEM_OFFSET,
-
- .rx_ring = 32,
- .tx_ring = 32,
- .rx_copybreak = 240,
- .use_napi = 0,
- .napi_weight = 17,
- .bus_id = "0:00",
- },
- [fsid_fcc2] = {
- .fs_no = fsid_fcc2,
- .cp_page = CPM_CR_FCC2_PAGE,
- .cp_block = CPM_CR_FCC2_SBLOCK,
- .clk_trx = (PC_F2RXCLK | PC_F2TXCLK),
- .clk_route = CMX2_CLK_ROUTE,
- .clk_mask = CMX2_CLK_MASK,
- .init_ioports = init_fcc2_ioports,
-
- .mem_offset = FCC2_MEM_OFFSET,
-
- .rx_ring = 32,
- .tx_ring = 32,
- .rx_copybreak = 240,
- .use_napi = 0,
- .napi_weight = 17,
- .bus_id = "0:03",
- },
-};
-
-static void init_fcc1_ioports(struct fs_platform_info* pdata)
-{
- struct io_port *io;
- u32 tempval;
- cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t));
- u32 *bcsr = ioremap(BCSR_ADDR+4, sizeof(u32));
-
- io = &immap->im_ioport;
-
- /* Enable the PHY */
- clrbits32(bcsr, BCSR1_FETHIEN);
- setbits32(bcsr, BCSR1_FETH_RST);
-
- /* FCC1 pins are on port A/C. */
- /* Configure port A and C pins for FCC1 Ethernet. */
-
- tempval = in_be32(&io->iop_pdira);
- tempval &= ~PA1_DIRA0;
- tempval |= PA1_DIRA1;
- out_be32(&io->iop_pdira, tempval);
-
- tempval = in_be32(&io->iop_psora);
- tempval &= ~PA1_PSORA0;
- tempval |= PA1_PSORA1;
- out_be32(&io->iop_psora, tempval);
-
- setbits32(&io->iop_ppara,PA1_DIRA0 | PA1_DIRA1);
-
- /* Alter clocks */
- tempval = PC_F1TXCLK|PC_F1RXCLK;
-
- clrbits32(&io->iop_psorc, tempval);
- clrbits32(&io->iop_pdirc, tempval);
- setbits32(&io->iop_pparc, tempval);
-
- clrbits32(&immap->im_cpmux.cmx_fcr, CMX1_CLK_MASK);
- setbits32(&immap->im_cpmux.cmx_fcr, CMX1_CLK_ROUTE);
- iounmap(bcsr);
- iounmap(immap);
-}
-
-static void init_fcc2_ioports(struct fs_platform_info* pdata)
-{
- cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t));
- u32 *bcsr = ioremap(BCSR_ADDR+12, sizeof(u32));
-
- struct io_port *io;
- u32 tempval;
-
- immap = cpm2_immr;
-
- io = &immap->im_ioport;
-
- /* Enable the PHY */
- clrbits32(bcsr, BCSR3_FETHIEN2);
- setbits32(bcsr, BCSR3_FETH2_RST);
-
- /* FCC2 are port B/C. */
- /* Configure port A and C pins for FCC2 Ethernet. */
-
- tempval = in_be32(&io->iop_pdirb);
- tempval &= ~PB2_DIRB0;
- tempval |= PB2_DIRB1;
- out_be32(&io->iop_pdirb, tempval);
-
- tempval = in_be32(&io->iop_psorb);
- tempval &= ~PB2_PSORB0;
- tempval |= PB2_PSORB1;
- out_be32(&io->iop_psorb, tempval);
-
- setbits32(&io->iop_pparb,PB2_DIRB0 | PB2_DIRB1);
-
- tempval = PC_F2RXCLK|PC_F2TXCLK;
-
- /* Alter clocks */
- clrbits32(&io->iop_psorc,tempval);
- clrbits32(&io->iop_pdirc,tempval);
- setbits32(&io->iop_pparc,tempval);
-
- clrbits32(&immap->im_cpmux.cmx_fcr, CMX2_CLK_MASK);
- setbits32(&immap->im_cpmux.cmx_fcr, CMX2_CLK_ROUTE);
-
- iounmap(bcsr);
- iounmap(immap);
-}
-
-
-static void __init mpc8272ads_fixup_enet_pdata(struct platform_device *pdev,
- int idx)
-{
- bd_t* bi = (void*)__res;
- int fs_no = fsid_fcc1+pdev->id-1;
-
- if(fs_no >= ARRAY_SIZE(mpc82xx_enet_pdata)) {
- return;
- }
-
- mpc82xx_enet_pdata[fs_no].dpram_offset=
- (u32)cpm2_immr->im_dprambase;
- mpc82xx_enet_pdata[fs_no].fcc_regs_c =
- (u32)cpm2_immr->im_fcc_c;
- memcpy(&mpc82xx_enet_pdata[fs_no].macaddr,bi->bi_enetaddr,6);
-
- /* prevent dup mac */
- if(fs_no == fsid_fcc2)
- mpc82xx_enet_pdata[fs_no].macaddr[5] ^= 1;
-
- pdev->dev.platform_data = &mpc82xx_enet_pdata[fs_no];
-}
-
-static void mpc8272ads_fixup_uart_pdata(struct platform_device *pdev,
- int idx)
-{
- bd_t *bd = (bd_t *) __res;
- struct fs_uart_platform_info *pinfo;
- int num = ARRAY_SIZE(mpc8272_uart_pdata);
- int id = fs_uart_id_scc2fsid(idx);
-
- /* no need to alter anything if console */
- if ((id < num) && (!pdev->dev.platform_data)) {
- pinfo = &mpc8272_uart_pdata[id];
- pinfo->uart_clk = bd->bi_intfreq;
- pdev->dev.platform_data = pinfo;
- }
-}
-
-static void init_scc1_uart_ioports(struct fs_uart_platform_info* pdata)
-{
- cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t));
-
- /* SCC1 is only on port D */
- setbits32(&immap->im_ioport.iop_ppard,0x00000003);
- clrbits32(&immap->im_ioport.iop_psord,0x00000001);
- setbits32(&immap->im_ioport.iop_psord,0x00000002);
- clrbits32(&immap->im_ioport.iop_pdird,0x00000001);
- setbits32(&immap->im_ioport.iop_pdird,0x00000002);
-
- /* Wire BRG1 to SCC1 */
- clrbits32(&immap->im_cpmux.cmx_scr,0x00ffffff);
-
- iounmap(immap);
-}
-
-static void init_scc4_uart_ioports(struct fs_uart_platform_info* pdata)
-{
- cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t));
-
- setbits32(&immap->im_ioport.iop_ppard,0x00000600);
- clrbits32(&immap->im_ioport.iop_psord,0x00000600);
- clrbits32(&immap->im_ioport.iop_pdird,0x00000200);
- setbits32(&immap->im_ioport.iop_pdird,0x00000400);
-
- /* Wire BRG4 to SCC4 */
- clrbits32(&immap->im_cpmux.cmx_scr,0x000000ff);
- setbits32(&immap->im_cpmux.cmx_scr,0x0000001b);
-
- iounmap(immap);
-}
-
-static void __init mpc8272ads_fixup_mdio_pdata(struct platform_device *pdev,
- int idx)
-{
- m82xx_mii_bb_pdata.irq[0] = PHY_INTERRUPT;
- m82xx_mii_bb_pdata.irq[1] = PHY_POLL;
- m82xx_mii_bb_pdata.irq[2] = PHY_POLL;
- m82xx_mii_bb_pdata.irq[3] = PHY_INTERRUPT;
- m82xx_mii_bb_pdata.irq[31] = PHY_POLL;
-
-
- m82xx_mii_bb_pdata.mdio_dat.offset =
- (u32)&cpm2_immr->im_ioport.iop_pdatc;
-
- m82xx_mii_bb_pdata.mdio_dir.offset =
- (u32)&cpm2_immr->im_ioport.iop_pdirc;
-
- m82xx_mii_bb_pdata.mdc_dat.offset =
- (u32)&cpm2_immr->im_ioport.iop_pdatc;
-
-
- pdev->dev.platform_data = &m82xx_mii_bb_pdata;
-}
-
-static int mpc8272ads_platform_notify(struct device *dev)
-{
- static const struct platform_notify_dev_map dev_map[] = {
- {
- .bus_id = "fsl-cpm-fcc",
- .rtn = mpc8272ads_fixup_enet_pdata,
- },
- {
- .bus_id = "fsl-cpm-scc:uart",
- .rtn = mpc8272ads_fixup_uart_pdata,
- },
- {
- .bus_id = "fsl-bb-mdio",
- .rtn = mpc8272ads_fixup_mdio_pdata,
- },
- {
- .bus_id = NULL
- }
- };
- platform_notify_map(dev_map,dev);
-
- return 0;
-
-}
-
-int __init mpc8272ads_init(void)
-{
- printk(KERN_NOTICE "mpc8272ads: Init\n");
-
- platform_notify = mpc8272ads_platform_notify;
-
- ppc_sys_device_initfunc();
-
- ppc_sys_device_disable_all();
- ppc_sys_device_enable(MPC82xx_CPM_FCC1);
- ppc_sys_device_enable(MPC82xx_CPM_FCC2);
-
- /* to be ready for console, let's attach pdata here */
-#ifdef CONFIG_SERIAL_CPM_SCC1
- ppc_sys_device_setfunc(MPC82xx_CPM_SCC1, PPC_SYS_FUNC_UART);
- ppc_sys_device_enable(MPC82xx_CPM_SCC1);
-
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SCC4
- ppc_sys_device_setfunc(MPC82xx_CPM_SCC4, PPC_SYS_FUNC_UART);
- ppc_sys_device_enable(MPC82xx_CPM_SCC4);
-#endif
-
- ppc_sys_device_enable(MPC82xx_MDIO_BB);
-
- return 0;
-}
-
-/*
- To prevent confusion, console selection is gross:
- by 0 assumed SCC1 and by 1 assumed SCC4
- */
-struct platform_device* early_uart_get_pdev(int index)
-{
- bd_t *bd = (bd_t *) __res;
- struct fs_uart_platform_info *pinfo;
-
- struct platform_device* pdev = NULL;
- if(index) { /*assume SCC4 here*/
- pdev = &ppc_sys_platform_devices[MPC82xx_CPM_SCC4];
- pinfo = &mpc8272_uart_pdata[fsid_scc4_uart];
- } else { /*over SCC1*/
- pdev = &ppc_sys_platform_devices[MPC82xx_CPM_SCC1];
- pinfo = &mpc8272_uart_pdata[fsid_scc1_uart];
- }
-
- pinfo->uart_clk = bd->bi_intfreq;
- pdev->dev.platform_data = pinfo;
- ppc_sys_fixup_mem_resource(pdev, CPM_MAP_ADDR);
- return NULL;
-}
-
-arch_initcall(mpc8272ads_init);
diff --git a/arch/ppc/platforms/mpc885ads.h b/arch/ppc/platforms/mpc885ads.h
deleted file mode 100644
index d3bbbb3..0000000
--- a/arch/ppc/platforms/mpc885ads.h
+++ /dev/null
@@ -1,93 +0,0 @@
-/*
- * A collection of structures, addresses, and values associated with
- * the Freescale MPC885ADS board.
- * Copied from the FADS stuff.
- *
- * Author: MontaVista Software, Inc.
- * source@mvista.com
- *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under the
- * terms of the GNU General Public License version 2. This program is licensed
- * "as is" without any warranty of any kind, whether express or implied.
- */
-
-#ifdef __KERNEL__
-#ifndef __ASM_MPC885ADS_H__
-#define __ASM_MPC885ADS_H__
-
-
-#include <asm/ppcboot.h>
-
-/* U-Boot maps BCSR to 0xff080000 */
-#define BCSR_ADDR ((uint)0xff080000)
-#define BCSR_SIZE ((uint)32)
-#define BCSR0 ((uint)(BCSR_ADDR + 0x00))
-#define BCSR1 ((uint)(BCSR_ADDR + 0x04))
-#define BCSR2 ((uint)(BCSR_ADDR + 0x08))
-#define BCSR3 ((uint)(BCSR_ADDR + 0x0c))
-#define BCSR4 ((uint)(BCSR_ADDR + 0x10))
-
-#define CFG_PHYDEV_ADDR ((uint)0xff0a0000)
-#define BCSR5 ((uint)(CFG_PHYDEV_ADDR + 0x300))
-
-#define IMAP_ADDR ((uint)0xff000000)
-#define IMAP_SIZE ((uint)(64 * 1024))
-
-#define PCMCIA_MEM_ADDR ((uint)0xff020000)
-#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
-
-/* Bits of interest in the BCSRs.
- */
-#define BCSR1_ETHEN ((uint)0x20000000)
-#define BCSR1_IRDAEN ((uint)0x10000000)
-#define BCSR1_RS232EN_1 ((uint)0x01000000)
-#define BCSR1_PCCEN ((uint)0x00800000)
-#define BCSR1_PCCVCC0 ((uint)0x00400000)
-#define BCSR1_PCCVPP0 ((uint)0x00200000)
-#define BCSR1_PCCVPP1 ((uint)0x00100000)
-#define BCSR1_PCCVPP_MASK (BCSR1_PCCVPP0 | BCSR1_PCCVPP1)
-#define BCSR1_RS232EN_2 ((uint)0x00040000)
-#define BCSR1_PCCVCC1 ((uint)0x00010000)
-#define BCSR1_PCCVCC_MASK (BCSR1_PCCVCC0 | BCSR1_PCCVCC1)
-
-#define BCSR4_ETH10_RST ((uint)0x80000000) /* 10Base-T PHY reset*/
-#define BCSR4_USB_LO_SPD ((uint)0x04000000)
-#define BCSR4_USB_VCC ((uint)0x02000000)
-#define BCSR4_USB_FULL_SPD ((uint)0x00040000)
-#define BCSR4_USB_EN ((uint)0x00020000)
-
-#define BCSR5_MII2_EN 0x40
-#define BCSR5_MII2_RST 0x20
-#define BCSR5_T1_RST 0x10
-#define BCSR5_ATM155_RST 0x08
-#define BCSR5_ATM25_RST 0x04
-#define BCSR5_MII1_EN 0x02
-#define BCSR5_MII1_RST 0x01
-
-/* Interrupt level assignments */
-#define PHY_INTERRUPT SIU_IRQ7 /* PHY link change interrupt */
-#define SIU_INT_FEC1 SIU_LEVEL1 /* FEC1 interrupt */
-#define SIU_INT_FEC2 SIU_LEVEL3 /* FEC2 interrupt */
-#define FEC_INTERRUPT SIU_INT_FEC1 /* FEC interrupt */
-
-/* We don't use the 8259 */
-#define NR_8259_INTS 0
-
-/* CPM Ethernet through SCC3 */
-#define PA_ENET_RXD ((ushort)0x0040)
-#define PA_ENET_TXD ((ushort)0x0080)
-#define PE_ENET_TCLK ((uint)0x00004000)
-#define PE_ENET_RCLK ((uint)0x00008000)
-#define PE_ENET_TENA ((uint)0x00000010)
-#define PC_ENET_CLSN ((ushort)0x0400)
-#define PC_ENET_RENA ((ushort)0x0800)
-
-/* Control bits in the SICR to route TCLK (CLK5) and RCLK (CLK6) to
- * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero */
-#define SICR_ENET_MASK ((uint)0x00ff0000)
-#define SICR_ENET_CLKRT ((uint)0x002c0000)
-
-#define BOARD_CHIP_NAME "MPC885"
-
-#endif /* __ASM_MPC885ADS_H__ */
-#endif /* __KERNEL__ */
diff --git a/arch/ppc/platforms/mpc885ads_setup.c b/arch/ppc/platforms/mpc885ads_setup.c
deleted file mode 100644
index ba06cc0..0000000
--- a/arch/ppc/platforms/mpc885ads_setup.c
+++ /dev/null
@@ -1,476 +0,0 @@
-/*arch/ppc/platforms/mpc885ads_setup.c
- *
- * Platform setup for the Freescale mpc885ads board
- *
- * Vitaly Bordug <vbordug@ru.mvista.com>
- *
- * Copyright 2005 MontaVista Software Inc.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/param.h>
-#include <linux/string.h>
-#include <linux/ioport.h>
-#include <linux/device.h>
-
-#include <linux/fs_enet_pd.h>
-#include <linux/fs_uart_pd.h>
-#include <linux/mii.h>
-
-#include <asm/delay.h>
-#include <asm/io.h>
-#include <asm/machdep.h>
-#include <asm/page.h>
-#include <asm/processor.h>
-#include <asm/system.h>
-#include <asm/time.h>
-#include <asm/ppcboot.h>
-#include <asm/8xx_immap.h>
-#include <asm/cpm1.h>
-#include <asm/ppc_sys.h>
-
-extern unsigned char __res[];
-static void setup_smc1_ioports(struct fs_uart_platform_info*);
-static void setup_smc2_ioports(struct fs_uart_platform_info*);
-
-static struct fs_mii_fec_platform_info mpc8xx_mdio_fec_pdata;
-static void setup_fec1_ioports(struct fs_platform_info*);
-static void setup_fec2_ioports(struct fs_platform_info*);
-static void setup_scc3_ioports(struct fs_platform_info*);
-
-static struct fs_uart_platform_info mpc885_uart_pdata[] = {
- [fsid_smc1_uart] = {
- .brg = 1,
- .fs_no = fsid_smc1_uart,
- .init_ioports = setup_smc1_ioports,
- .tx_num_fifo = 4,
- .tx_buf_size = 32,
- .rx_num_fifo = 4,
- .rx_buf_size = 32,
- },
- [fsid_smc2_uart] = {
- .brg = 2,
- .fs_no = fsid_smc2_uart,
- .init_ioports = setup_smc2_ioports,
- .tx_num_fifo = 4,
- .tx_buf_size = 32,
- .rx_num_fifo = 4,
- .rx_buf_size = 32,
- },
-};
-
-static struct fs_platform_info mpc8xx_enet_pdata[] = {
- [fsid_fec1] = {
- .rx_ring = 128,
- .tx_ring = 16,
- .rx_copybreak = 240,
-
- .use_napi = 1,
- .napi_weight = 17,
-
- .init_ioports = setup_fec1_ioports,
-
- .bus_id = "0:00",
- .has_phy = 1,
- },
- [fsid_fec2] = {
- .rx_ring = 128,
- .tx_ring = 16,
- .rx_copybreak = 240,
-
- .use_napi = 1,
- .napi_weight = 17,
-
- .init_ioports = setup_fec2_ioports,
-
- .bus_id = "0:01",
- .has_phy = 1,
- },
- [fsid_scc3] = {
- .rx_ring = 64,
- .tx_ring = 8,
- .rx_copybreak = 240,
-
- .use_napi = 1,
- .napi_weight = 17,
-
- .init_ioports = setup_scc3_ioports,
-#ifdef CONFIG_FIXED_MII_10_FDX
- .bus_id = "fixed@100:1",
-#else
- .bus_id = "0:02",
- #endif
- },
-};
-
-void __init board_init(void)
-{
- cpm8xx_t *cp = cpmp;
- unsigned int *bcsr_io;
-
-#ifdef CONFIG_FS_ENET
- immap_t *immap = (immap_t *) IMAP_ADDR;
-#endif
- bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
-
- if (bcsr_io == NULL) {
- printk(KERN_CRIT "Could not remap BCSR\n");
- return;
- }
-#ifdef CONFIG_SERIAL_CPM_SMC1
- cp->cp_simode &= ~(0xe0000000 >> 17); /* brg1 */
- clrbits32(bcsr_io, BCSR1_RS232EN_1);
- cp->cp_smc[0].smc_smcm |= (SMCM_RX | SMCM_TX);
- cp->cp_smc[0].smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
-#else
- setbits32(bcsr_io,BCSR1_RS232EN_1);
- cp->cp_smc[0].smc_smcmr = 0;
- cp->cp_smc[0].smc_smce = 0;
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SMC2
- cp->cp_simode &= ~(0xe0000000 >> 1);
- cp->cp_simode |= (0x20000000 >> 1); /* brg2 */
- clrbits32(bcsr_io,BCSR1_RS232EN_2);
- cp->cp_smc[1].smc_smcm |= (SMCM_RX | SMCM_TX);
- cp->cp_smc[1].smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
-#else
- setbits32(bcsr_io,BCSR1_RS232EN_2);
- cp->cp_smc[1].smc_smcmr = 0;
- cp->cp_smc[1].smc_smce = 0;
-#endif
- iounmap(bcsr_io);
-
-#ifdef CONFIG_FS_ENET
- /* use MDC for MII (common) */
- setbits16(&immap->im_ioport.iop_pdpar, 0x0080);
- clrbits16(&immap->im_ioport.iop_pddir, 0x0080);
- bcsr_io = ioremap(BCSR5, sizeof(unsigned long));
- clrbits32(bcsr_io,BCSR5_MII1_EN);
- clrbits32(bcsr_io,BCSR5_MII1_RST);
-#ifdef CONFIG_MPC8xx_SECOND_ETH_FEC2
- clrbits32(bcsr_io,BCSR5_MII2_EN);
- clrbits32(bcsr_io,BCSR5_MII2_RST);
-#endif
- iounmap(bcsr_io);
-#endif
-}
-
-static void setup_fec1_ioports(struct fs_platform_info* pdata)
-{
- immap_t *immap = (immap_t *) IMAP_ADDR;
-
- /* configure FEC1 pins */
- setbits16(&immap->im_ioport.iop_papar, 0xf830);
- setbits16(&immap->im_ioport.iop_padir, 0x0830);
- clrbits16(&immap->im_ioport.iop_padir, 0xf000);
- setbits32(&immap->im_cpm.cp_pbpar, 0x00001001);
-
- clrbits32(&immap->im_cpm.cp_pbdir, 0x00001001);
- setbits16(&immap->im_ioport.iop_pcpar, 0x000c);
- clrbits16(&immap->im_ioport.iop_pcdir, 0x000c);
- setbits32(&immap->im_cpm.cp_pepar, 0x00000003);
-
- setbits32(&immap->im_cpm.cp_pedir, 0x00000003);
- clrbits32(&immap->im_cpm.cp_peso, 0x00000003);
- clrbits32(&immap->im_cpm.cp_cptr, 0x00000100);
-}
-
-static void setup_fec2_ioports(struct fs_platform_info* pdata)
-{
- immap_t *immap = (immap_t *) IMAP_ADDR;
-
- /* configure FEC2 pins */
- setbits32(&immap->im_cpm.cp_pepar, 0x0003fffc);
- setbits32(&immap->im_cpm.cp_pedir, 0x0003fffc);
- clrbits32(&immap->im_cpm.cp_peso, 0x000087fc);
- setbits32(&immap->im_cpm.cp_peso, 0x00037800);
- clrbits32(&immap->im_cpm.cp_cptr, 0x00000080);
-}
-
-static void setup_scc3_ioports(struct fs_platform_info* pdata)
-{
- immap_t *immap = (immap_t *) IMAP_ADDR;
- unsigned *bcsr_io;
-
- bcsr_io = ioremap(BCSR_ADDR, BCSR_SIZE);
-
- if (bcsr_io == NULL) {
- printk(KERN_CRIT "Could not remap BCSR\n");
- return;
- }
-
- /* Enable the PHY.
- */
- clrbits32(bcsr_io+4, BCSR4_ETH10_RST);
- udelay(1000);
- setbits32(bcsr_io+4, BCSR4_ETH10_RST);
- /* Configure port A pins for Txd and Rxd.
- */
- setbits16(&immap->im_ioport.iop_papar, PA_ENET_RXD | PA_ENET_TXD);
- clrbits16(&immap->im_ioport.iop_padir, PA_ENET_RXD | PA_ENET_TXD);
-
- /* Configure port C pins to enable CLSN and RENA.
- */
- clrbits16(&immap->im_ioport.iop_pcpar, PC_ENET_CLSN | PC_ENET_RENA);
- clrbits16(&immap->im_ioport.iop_pcdir, PC_ENET_CLSN | PC_ENET_RENA);
- setbits16(&immap->im_ioport.iop_pcso, PC_ENET_CLSN | PC_ENET_RENA);
-
- /* Configure port E for TCLK and RCLK.
- */
- setbits32(&immap->im_cpm.cp_pepar, PE_ENET_TCLK | PE_ENET_RCLK);
- clrbits32(&immap->im_cpm.cp_pepar, PE_ENET_TENA);
- clrbits32(&immap->im_cpm.cp_pedir,
- PE_ENET_TCLK | PE_ENET_RCLK | PE_ENET_TENA);
- clrbits32(&immap->im_cpm.cp_peso, PE_ENET_TCLK | PE_ENET_RCLK);
- setbits32(&immap->im_cpm.cp_peso, PE_ENET_TENA);
-
- /* Configure Serial Interface clock routing.
- * First, clear all SCC bits to zero, then set the ones we want.
- */
- clrbits32(&immap->im_cpm.cp_sicr, SICR_ENET_MASK);
- setbits32(&immap->im_cpm.cp_sicr, SICR_ENET_CLKRT);
-
- /* Disable Rx and Tx. SMC1 sshould be stopped if SCC3 eternet are used.
- */
- immap->im_cpm.cp_smc[0].smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
- /* On the MPC885ADS SCC ethernet PHY is initialized in the full duplex mode
- * by H/W setting after reset. SCC ethernet controller support only half duplex.
- * This discrepancy of modes causes a lot of carrier lost errors.
- */
-
- /* In the original SCC enet driver the following code is placed at
- the end of the initialization */
- setbits32(&immap->im_cpm.cp_pepar, PE_ENET_TENA);
- clrbits32(&immap->im_cpm.cp_pedir, PE_ENET_TENA);
- setbits32(&immap->im_cpm.cp_peso, PE_ENET_TENA);
-
- setbits32(bcsr_io+4, BCSR1_ETHEN);
- iounmap(bcsr_io);
-}
-
-static int mac_count = 0;
-
-static void mpc885ads_fixup_enet_pdata(struct platform_device *pdev, int fs_no)
-{
- struct fs_platform_info *fpi;
- bd_t *bd = (bd_t *) __res;
- char *e;
- int i;
-
- if(fs_no >= ARRAY_SIZE(mpc8xx_enet_pdata)) {
- printk(KERN_ERR"No network-suitable #%d device on bus", fs_no);
- return;
- }
-
- fpi = &mpc8xx_enet_pdata[fs_no];
-
- switch (fs_no) {
- case fsid_fec1:
- fpi->init_ioports = &setup_fec1_ioports;
- break;
- case fsid_fec2:
- fpi->init_ioports = &setup_fec2_ioports;
- break;
- case fsid_scc3:
- fpi->init_ioports = &setup_scc3_ioports;
- break;
- default:
- printk(KERN_WARNING "Device %s is not supported!\n", pdev->name);
- return;
- }
-
- pdev->dev.platform_data = fpi;
- fpi->fs_no = fs_no;
-
- e = (unsigned char *)&bd->bi_enetaddr;
- for (i = 0; i < 6; i++)
- fpi->macaddr[i] = *e++;
-
- fpi->macaddr[5] += mac_count++;
-
-}
-
-static void mpc885ads_fixup_fec_enet_pdata(struct platform_device *pdev,
- int idx)
-{
- /* This is for FEC devices only */
- if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-fec")))
- return;
- mpc885ads_fixup_enet_pdata(pdev, fsid_fec1 + pdev->id - 1);
-}
-
-static void __init mpc885ads_fixup_scc_enet_pdata(struct platform_device *pdev,
- int idx)
-{
- /* This is for SCC devices only */
- if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-scc")))
- return;
-
- mpc885ads_fixup_enet_pdata(pdev, fsid_scc1 + pdev->id - 1);
-}
-
-static void setup_smc1_ioports(struct fs_uart_platform_info* pdata)
-{
- immap_t *immap = (immap_t *) IMAP_ADDR;
- unsigned *bcsr_io;
- unsigned int iobits = 0x000000c0;
-
- bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
-
- if (bcsr_io == NULL) {
- printk(KERN_CRIT "Could not remap BCSR1\n");
- return;
- }
- clrbits32(bcsr_io,BCSR1_RS232EN_1);
- iounmap(bcsr_io);
-
- setbits32(&immap->im_cpm.cp_pbpar, iobits);
- clrbits32(&immap->im_cpm.cp_pbdir, iobits);
- clrbits16(&immap->im_cpm.cp_pbodr, iobits);
-}
-
-static void setup_smc2_ioports(struct fs_uart_platform_info* pdata)
-{
- immap_t *immap = (immap_t *) IMAP_ADDR;
- unsigned *bcsr_io;
- unsigned int iobits = 0x00000c00;
-
- bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
-
- if (bcsr_io == NULL) {
- printk(KERN_CRIT "Could not remap BCSR1\n");
- return;
- }
- clrbits32(bcsr_io,BCSR1_RS232EN_2);
- iounmap(bcsr_io);
-
-#ifndef CONFIG_SERIAL_CPM_ALT_SMC2
- setbits32(&immap->im_cpm.cp_pbpar, iobits);
- clrbits32(&immap->im_cpm.cp_pbdir, iobits);
- clrbits16(&immap->im_cpm.cp_pbodr, iobits);
-#else
- setbits16(&immap->im_ioport.iop_papar, iobits);
- clrbits16(&immap->im_ioport.iop_padir, iobits);
- clrbits16(&immap->im_ioport.iop_paodr, iobits);
-#endif
-}
-
-static void __init mpc885ads_fixup_uart_pdata(struct platform_device *pdev,
- int idx)
-{
- bd_t *bd = (bd_t *) __res;
- struct fs_uart_platform_info *pinfo;
- int num = ARRAY_SIZE(mpc885_uart_pdata);
-
- int id = fs_uart_id_smc2fsid(idx);
-
- /* no need to alter anything if console */
- if ((id < num) && (!pdev->dev.platform_data)) {
- pinfo = &mpc885_uart_pdata[id];
- pinfo->uart_clk = bd->bi_intfreq;
- pdev->dev.platform_data = pinfo;
- }
-}
-
-
-static int mpc885ads_platform_notify(struct device *dev)
-{
-
- static const struct platform_notify_dev_map dev_map[] = {
- {
- .bus_id = "fsl-cpm-fec",
- .rtn = mpc885ads_fixup_fec_enet_pdata,
- },
- {
- .bus_id = "fsl-cpm-scc",
- .rtn = mpc885ads_fixup_scc_enet_pdata,
- },
- {
- .bus_id = "fsl-cpm-smc:uart",
- .rtn = mpc885ads_fixup_uart_pdata
- },
- {
- .bus_id = NULL
- }
- };
-
- platform_notify_map(dev_map,dev);
-
- return 0;
-}
-
-int __init mpc885ads_init(void)
-{
- struct fs_mii_fec_platform_info* fmpi;
- bd_t *bd = (bd_t *) __res;
-
- printk(KERN_NOTICE "mpc885ads: Init\n");
-
- platform_notify = mpc885ads_platform_notify;
-
- ppc_sys_device_initfunc();
- ppc_sys_device_disable_all();
-
- ppc_sys_device_enable(MPC8xx_CPM_FEC1);
-
- ppc_sys_device_enable(MPC8xx_MDIO_FEC);
- fmpi = ppc_sys_platform_devices[MPC8xx_MDIO_FEC].dev.platform_data =
- &mpc8xx_mdio_fec_pdata;
-
- fmpi->mii_speed = ((((bd->bi_intfreq + 4999999) / 2500000) / 2) & 0x3F) << 1;
-
- /* No PHY interrupt line here */
- fmpi->irq[0xf] = SIU_IRQ7;
-
-#ifdef CONFIG_MPC8xx_SECOND_ETH_SCC3
- ppc_sys_device_enable(MPC8xx_CPM_SCC3);
-
-#endif
-#ifdef CONFIG_MPC8xx_SECOND_ETH_FEC2
- ppc_sys_device_enable(MPC8xx_CPM_FEC2);
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SMC1
- ppc_sys_device_enable(MPC8xx_CPM_SMC1);
- ppc_sys_device_setfunc(MPC8xx_CPM_SMC1, PPC_SYS_FUNC_UART);
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SMC2
- ppc_sys_device_enable(MPC8xx_CPM_SMC2);
- ppc_sys_device_setfunc(MPC8xx_CPM_SMC2, PPC_SYS_FUNC_UART);
-#endif
- return 0;
-}
-
-arch_initcall(mpc885ads_init);
-
-/*
- To prevent confusion, console selection is gross:
- by 0 assumed SMC1 and by 1 assumed SMC2
- */
-struct platform_device* early_uart_get_pdev(int index)
-{
- bd_t *bd = (bd_t *) __res;
- struct fs_uart_platform_info *pinfo;
-
- struct platform_device* pdev = NULL;
- if(index) { /*assume SMC2 here*/
- pdev = &ppc_sys_platform_devices[MPC8xx_CPM_SMC2];
- pinfo = &mpc885_uart_pdata[1];
- } else { /*over SMC1*/
- pdev = &ppc_sys_platform_devices[MPC8xx_CPM_SMC1];
- pinfo = &mpc885_uart_pdata[0];
- }
-
- pinfo->uart_clk = bd->bi_intfreq;
- pdev->dev.platform_data = pinfo;
- ppc_sys_fixup_mem_resource(pdev, IMAP_ADDR);
- return NULL;
-}
-
diff --git a/arch/ppc/platforms/pq2ads.c b/arch/ppc/platforms/pq2ads.c
deleted file mode 100644
index 7fc2e02..0000000
--- a/arch/ppc/platforms/pq2ads.c
+++ /dev/null
@@ -1,53 +0,0 @@
-/*
- * PQ2ADS platform support
- *
- * Author: Kumar Gala <galak@kernel.crashing.org>
- * Derived from: est8260_setup.c by Allen Curtis
- *
- * Copyright 2004 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#include <linux/init.h>
-
-#include <asm/io.h>
-#include <asm/mpc8260.h>
-#include <asm/cpm2.h>
-#include <asm/immap_cpm2.h>
-
-void __init
-m82xx_board_setup(void)
-{
- cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t));
- u32 *bcsr = ioremap(BCSR_ADDR+4, sizeof(u32));
-
- /* Enable the 2nd UART port */
- clrbits32(bcsr, BCSR1_RS232_EN2);
-
-#ifdef CONFIG_SERIAL_CPM_SCC1
- clrbits32((u32*)&immap->im_scc[0].scc_sccm, UART_SCCM_TX | UART_SCCM_RX);
- clrbits32((u32*)&immap->im_scc[0].scc_gsmrl, SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SCC2
- clrbits32((u32*)&immap->im_scc[1].scc_sccm, UART_SCCM_TX | UART_SCCM_RX);
- clrbits32((u32*)&immap->im_scc[1].scc_gsmrl, SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SCC3
- clrbits32((u32*)&immap->im_scc[2].scc_sccm, UART_SCCM_TX | UART_SCCM_RX);
- clrbits32((u32*)&immap->im_scc[2].scc_gsmrl, SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-#endif
-
-#ifdef CONFIG_SERIAL_CPM_SCC4
- clrbits32((u32*)&immap->im_scc[3].scc_sccm, UART_SCCM_TX | UART_SCCM_RX);
- clrbits32((u32*)&immap->im_scc[3].scc_gsmrl, SCC_GSMRL_ENR | SCC_GSMRL_ENT);
-#endif
-
- iounmap(bcsr);
- iounmap(immap);
-}
diff --git a/arch/ppc/platforms/pq2ads.h b/arch/ppc/platforms/pq2ads.h
deleted file mode 100644
index 2b287f4..0000000
--- a/arch/ppc/platforms/pq2ads.h
+++ /dev/null
@@ -1,94 +0,0 @@
-/*
- * A collection of structures, addresses, and values associated with
- * the Motorola MPC8260ADS/MPC8266ADS-PCI boards.
- * Copied from the RPX-Classic and SBS8260 stuff.
- *
- * Copyright (c) 2001 Dan Malek (dan@mvista.com)
- */
-#ifdef __KERNEL__
-#ifndef __MACH_ADS8260_DEFS
-#define __MACH_ADS8260_DEFS
-
-
-#include <asm/ppcboot.h>
-
-#if defined(CONFIG_ADS8272)
-#define BOARD_CHIP_NAME "8272"
-#endif
-
-/* Memory map is configured by the PROM startup.
- * We just map a few things we need. The CSR is actually 4 byte-wide
- * registers that can be accessed as 8-, 16-, or 32-bit values.
- */
-#define CPM_MAP_ADDR ((uint)0xf0000000)
-#define BCSR_ADDR ((uint)0xf4500000)
-#define BCSR_SIZE ((uint)(32 * 1024))
-
-#define BOOTROM_RESTART_ADDR ((uint)0xff000104)
-
-/* For our show_cpuinfo hooks. */
-#define CPUINFO_VENDOR "Motorola"
-#define CPUINFO_MACHINE "PQ2 ADS PowerPC"
-
-/* The ADS8260 has 16, 32-bit wide control/status registers, accessed
- * only on word boundaries.
- * Not all are used (yet), or are interesting to us (yet).
- */
-
-/* Things of interest in the CSR.
-*/
-#define BCSR0_LED0 ((uint)0x02000000) /* 0 == on */
-#define BCSR0_LED1 ((uint)0x01000000) /* 0 == on */
-#define BCSR1_FETHIEN ((uint)0x08000000) /* 0 == enable */
-#define BCSR1_FETH_RST ((uint)0x04000000) /* 0 == reset */
-#define BCSR1_RS232_EN1 ((uint)0x02000000) /* 0 == enable */
-#define BCSR1_RS232_EN2 ((uint)0x01000000) /* 0 == enable */
-#define BCSR3_FETHIEN2 ((uint)0x10000000) /* 0 == enable */
-#define BCSR3_FETH2_RST ((uint)0x80000000) /* 0 == reset */
-
-#define PHY_INTERRUPT SIU_INT_IRQ7
-
-#ifdef CONFIG_PCI
-/* PCI interrupt controller */
-#define PCI_INT_STAT_REG 0xF8200000
-#define PCI_INT_MASK_REG 0xF8200004
-#define PIRQA (NR_CPM_INTS + 0)
-#define PIRQB (NR_CPM_INTS + 1)
-#define PIRQC (NR_CPM_INTS + 2)
-#define PIRQD (NR_CPM_INTS + 3)
-
-/*
- * PCI memory map definitions for MPC8266ADS-PCI.
- *
- * processor view
- * local address PCI address target
- * 0x80000000-0x9FFFFFFF 0x80000000-0x9FFFFFFF PCI mem with prefetch
- * 0xA0000000-0xBFFFFFFF 0xA0000000-0xBFFFFFFF PCI mem w/o prefetch
- * 0xF4000000-0xF7FFFFFF 0x00000000-0x03FFFFFF PCI IO
- *
- * PCI master view
- * local address PCI address target
- * 0x00000000-0x1FFFFFFF 0x00000000-0x1FFFFFFF MPC8266 local memory
- */
-
-/* All the other PCI memory map definitions reside at syslib/m82xx_pci.h
- Here we should redefine what is unique for this board */
-#define M82xx_PCI_SLAVE_MEM_LOCAL 0x00000000 /* Local base */
-#define M82xx_PCI_SLAVE_MEM_BUS 0x00000000 /* PCI base */
-#define M82xx_PCI_SLAVE_MEM_SIZE 0x10000000 /* 256 Mb */
-
-#define M82xx_PCI_SLAVE_SEC_WND_SIZE ~(0x40000000 - 1U) /* 2 x 512Mb */
-#define M82xx_PCI_SLAVE_SEC_WND_BASE 0x80000000 /* PCI Memory base */
-
-#if defined(CONFIG_ADS8272)
-#define PCI_INT_TO_SIU SIU_INT_IRQ2
-#elif defined(CONFIG_PQ2FADS)
-#define PCI_INT_TO_SIU SIU_INT_IRQ6
-#else
-#warning PCI Bridge will be without interrupts support
-#endif
-
-#endif /* CONFIG_PCI */
-
-#endif /* __MACH_ADS8260_DEFS */
-#endif /* __KERNEL__ */
diff --git a/arch/ppc/platforms/pq2ads_pd.h b/arch/ppc/platforms/pq2ads_pd.h
deleted file mode 100644
index 672483d..0000000
--- a/arch/ppc/platforms/pq2ads_pd.h
+++ /dev/null
@@ -1,32 +0,0 @@
-#ifndef __PQ2ADS_PD_H
-#define __PQ2ADS_PD_H
-/*
- * arch/ppc/platforms/82xx/pq2ads_pd.h
- *
- * Some defines for MPC82xx board-specific PlatformDevice descriptions
- *
- * 2005 (c) MontaVista Software, Inc.
- * Vitaly Bordug <vbordug@ru.mvista.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-/* FCC1 Clock Source Configuration. These can be redefined in the board specific file.
- Can only choose from CLK9-12 */
-
-#define F1_RXCLK 11
-#define F1_TXCLK 10
-
-/* FCC2 Clock Source Configuration. These can be redefined in the board specific file.
- Can only choose from CLK13-16 */
-#define F2_RXCLK 15
-#define F2_TXCLK 16
-
-/* FCC3 Clock Source Configuration. These can be redefined in the board specific file.
- Can only choose from CLK13-16 */
-#define F3_RXCLK 13
-#define F3_TXCLK 14
-
-#endif
diff --git a/arch/ppc/syslib/m8260_setup.c b/arch/ppc/syslib/m8260_setup.c
index 46588fa..b405837 100644
--- a/arch/ppc/syslib/m8260_setup.c
+++ b/arch/ppc/syslib/m8260_setup.c
@@ -175,12 +175,6 @@
* in case the boot rom changed something on us.
*/
cpm2_immr->im_intctl.ic_siprr = 0x05309770;
-
-#if defined(CONFIG_PCI) && (defined(CONFIG_ADS8272) || defined(CONFIG_PQ2FADS))
- /* Initialize stuff for the 82xx CPLD IC and install demux */
- pq2pci_init_irq();
-#endif
-
}
/*
diff --git a/arch/ppc/syslib/m82xx_pci.c b/arch/ppc/syslib/m82xx_pci.c
index fe860d5..657a1c2 100644
--- a/arch/ppc/syslib/m82xx_pci.c
+++ b/arch/ppc/syslib/m82xx_pci.c
@@ -150,14 +150,6 @@
{
int irq;
volatile cpm2_map_t *immap = cpm2_immr;
-#if defined CONFIG_ADS8272
- /* configure chip select for PCI interrupt controller */
- immap->im_memctl.memc_br3 = PCI_INT_STAT_REG | 0x00001801;
- immap->im_memctl.memc_or3 = 0xffff8010;
-#elif defined CONFIG_PQ2FADS
- immap->im_memctl.memc_br8 = PCI_INT_STAT_REG | 0x00001801;
- immap->im_memctl.memc_or8 = 0xffff8010;
-#endif
for (irq = NR_CPM_INTS; irq < NR_CPM_INTS + 4; irq++)
irq_desc[irq].chip = &pq2pci_ic;
@@ -222,26 +214,6 @@
immap->im_memctl.memc_pcibr1 = M82xx_PCI_SEC_WND_BASE | PCIBR_ENABLE;
#endif
-#if defined CONFIG_ADS8272
- immap->im_siu_conf.siu_82xx.sc_siumcr =
- (immap->im_siu_conf.siu_82xx.sc_siumcr &
- ~(SIUMCR_BBD | SIUMCR_ESE | SIUMCR_PBSE |
- SIUMCR_CDIS | SIUMCR_DPPC11 | SIUMCR_L2CPC11 |
- SIUMCR_LBPC11 | SIUMCR_APPC11 |
- SIUMCR_CS10PC11 | SIUMCR_BCTLC11 | SIUMCR_MMR11)) |
- SIUMCR_DPPC11 | SIUMCR_L2CPC01 | SIUMCR_LBPC00 |
- SIUMCR_APPC10 | SIUMCR_CS10PC00 |
- SIUMCR_BCTLC00 | SIUMCR_MMR11 ;
-
-#elif defined CONFIG_PQ2FADS
- /*
- * Setting required to enable IRQ1-IRQ7 (SIUMCR [DPPC]),
- * and local bus for PCI (SIUMCR [LBPC]).
- */
- immap->im_siu_conf.siu_82xx.sc_siumcr = (immap->im_siu_conf.siu_82xx.sc_siumcr &
- ~(SIUMCR_L2CPC11 | SIUMCR_LBPC11 | SIUMCR_CS10PC11 | SIUMCR_APPC11) |
- SIUMCR_BBD | SIUMCR_LBPC01 | SIUMCR_DPPC11 | SIUMCR_APPC10);
-#endif
/* Enable PCI */
immap->im_pci.pci_gcr = cpu_to_le32(PCIGCR_PCI_BUS_EN);
@@ -284,12 +256,6 @@
immap->im_pci.pci_pibar0 = cpu_to_le32(M82xx_PCI_SLAVE_MEM_BUS >> PITA_ADDR_SHIFT);
immap->im_pci.pci_pitar0 = cpu_to_le32(M82xx_PCI_SLAVE_MEM_LOCAL>> PITA_ADDR_SHIFT);
-#if defined CONFIG_ADS8272
- /* PCI int highest prio */
- immap->im_siu_conf.siu_82xx.sc_ppc_alrh = 0x01236745;
-#elif defined CONFIG_PQ2FADS
- immap->im_siu_conf.siu_82xx.sc_ppc_alrh = 0x03124567;
-#endif
/* park bus on PCI */
immap->im_siu_conf.siu_82xx.sc_ppc_acr = PPC_ACR_BUS_PARK_PCI;
@@ -320,10 +286,6 @@
hose->bus_offset = 0;
hose->last_busno = 0xff;
-#ifdef CONFIG_ADS8272
- hose->set_cfg_type = 1;
-#endif
-
setup_m8260_indirect_pci(hose,
(unsigned long)&cpm2_immr->im_pci.pci_cfg_addr,
(unsigned long)&cpm2_immr->im_pci.pci_cfg_data);
diff --git a/arch/ppc/syslib/m8xx_setup.c b/arch/ppc/syslib/m8xx_setup.c
index 19749e9..18da720 100644
--- a/arch/ppc/syslib/m8xx_setup.c
+++ b/arch/ppc/syslib/m8xx_setup.c
@@ -141,16 +141,6 @@
#endif
#endif
-#if defined (CONFIG_MPC86XADS) || defined (CONFIG_MPC885ADS)
-#if defined(CONFIG_MTD_PHYSMAP)
- physmap_configure(binfo->bi_flashstart, binfo->bi_flashsize,
- MPC8xxADS_BANK_WIDTH, NULL);
-#ifdef CONFIG_MTD_PARTITIONS
- physmap_set_partitions(mpc8xxads_partitions, mpc8xxads_part_num);
-#endif /* CONFIG_MTD_PARTITIONS */
-#endif /* CONFIG_MTD_PHYSMAP */
-#endif
-
board_init();
}
diff --git a/include/asm-ppc/mpc8260.h b/include/asm-ppc/mpc8260.h
index 23579d4..402ba15 100644
--- a/include/asm-ppc/mpc8260.h
+++ b/include/asm-ppc/mpc8260.h
@@ -35,10 +35,6 @@
#include <platforms/tqm8260.h>
#endif
-#if defined(CONFIG_PQ2ADS) || defined (CONFIG_PQ2FADS)
-#include <platforms/pq2ads.h>
-#endif
-
#ifdef CONFIG_PCI_8260
#include <syslib/m82xx_pci.h>
#endif
diff --git a/include/asm-ppc/mpc8xx.h b/include/asm-ppc/mpc8xx.h
index d3a2f2f..b9e3060 100644
--- a/include/asm-ppc/mpc8xx.h
+++ b/include/asm-ppc/mpc8xx.h
@@ -63,10 +63,6 @@
#include <platforms/lantec.h>
#endif
-#if defined(CONFIG_MPC885ADS)
-#include <platforms/mpc885ads.h>
-#endif
-
/* Currently, all 8xx boards that support a processor to PCI/ISA bridge
* use the same memory map.
*/