i.MX serial: do not use #ifdef CONFIG_ARCH_*
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c
index 5d7b58f..7485afd 100644
--- a/drivers/serial/imx.c
+++ b/drivers/serial/imx.c
@@ -67,21 +67,8 @@
#define UBIR 0xa4 /* BRM Incremental Register */
#define UBMR 0xa8 /* BRM Modulator Register */
#define UBRC 0xac /* Baud Rate Count Register */
-#if defined CONFIG_ARCH_MX3 || defined CONFIG_ARCH_MX2
-#define ONEMS 0xb0 /* One Millisecond register */
-#define UTS 0xb4 /* UART Test Register */
-#endif
-#ifdef CONFIG_ARCH_MX1
-#define BIPR1 0xb0 /* Incremental Preset Register 1 */
-#define BIPR2 0xb4 /* Incremental Preset Register 2 */
-#define BIPR3 0xb8 /* Incremental Preset Register 3 */
-#define BIPR4 0xbc /* Incremental Preset Register 4 */
-#define BMPR1 0xc0 /* BRM Modulator Register 1 */
-#define BMPR2 0xc4 /* BRM Modulator Register 2 */
-#define BMPR3 0xc8 /* BRM Modulator Register 3 */
-#define BMPR4 0xcc /* BRM Modulator Register 4 */
-#define UTS 0xd0 /* UART Test Register */
-#endif
+#define MX2_ONEMS 0xb0 /* One Millisecond register */
+#define UTS (cpu_is_mx1() ? 0xd0 : 0xb4) /* UART Test Register */
/* UART Control Register Bit Fields.*/
#define URXD_CHARRDY (1<<15)
@@ -101,12 +88,7 @@
#define UCR1_RTSDEN (1<<5) /* RTS delta interrupt enable */
#define UCR1_SNDBRK (1<<4) /* Send break */
#define UCR1_TDMAEN (1<<3) /* Transmitter ready DMA enable */
-#ifdef CONFIG_ARCH_MX1
-#define UCR1_UARTCLKEN (1<<2) /* UART clock enabled */
-#endif
-#if defined CONFIG_ARCH_MX3 || defined CONFIG_ARCH_MX2
-#define UCR1_UARTCLKEN (0) /* not present on mx2/mx3 */
-#endif
+#define MX1_UCR1_UARTCLKEN (1<<2) /* UART clock enabled, mx1 only */
#define UCR1_DOZE (1<<1) /* Doze */
#define UCR1_UARTEN (1<<0) /* UART enabled */
#define UCR2_ESCI (1<<15) /* Escape seq interrupt enable */
@@ -132,13 +114,9 @@
#define UCR3_RXDSEN (1<<6) /* Receive status interrupt enable */
#define UCR3_AIRINTEN (1<<5) /* Async IR wake interrupt enable */
#define UCR3_AWAKEN (1<<4) /* Async wake interrupt enable */
-#ifdef CONFIG_ARCH_MX1
-#define UCR3_REF25 (1<<3) /* Ref freq 25 MHz, only on mx1 */
-#define UCR3_REF30 (1<<2) /* Ref Freq 30 MHz, only on mx1 */
-#endif
-#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3
-#define UCR3_RXDMUXSEL (1<<2) /* RXD Muxed Input Select, on mx2/mx3 */
-#endif
+#define MX1_UCR3_REF25 (1<<3) /* Ref freq 25 MHz, only on mx1 */
+#define MX1_UCR3_REF30 (1<<2) /* Ref Freq 30 MHz, only on mx1 */
+#define MX2_UCR3_RXDMUXSEL (1<<2) /* RXD Muxed Input Select, on mx2/mx3 */
#define UCR3_INVT (1<<1) /* Inverted Infrared transmission */
#define UCR3_BPEN (1<<0) /* Preset registers enable */
#define UCR4_CTSTL_32 (32<<10) /* CTS trigger level (32 chars) */
@@ -186,12 +164,10 @@
#define UTS_SOFTRST (1<<0) /* Software reset */
/* We've been assigned a range on the "Low-density serial ports" major */
-#ifdef CONFIG_ARCH_MXC
#define SERIAL_IMX_MAJOR 207
#define MINOR_START 16
#define DEV_NAME "ttymxc"
#define MAX_INTERNAL_IRQ MXC_INTERNAL_IRQS
-#endif
/*
* This determines how often we check the modem status signals
@@ -706,11 +682,11 @@
}
}
-#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3
- temp = readl(sport->port.membase + UCR3);
- temp |= UCR3_RXDMUXSEL;
- writel(temp, sport->port.membase + UCR3);
-#endif
+ if (!cpu_is_mx1()) {
+ temp = readl(sport->port.membase + UCR3);
+ temp |= MX2_UCR3_RXDMUXSEL;
+ writel(temp, sport->port.membase + UCR3);
+ }
if (USE_IRDA(sport)) {
temp = readl(sport->port.membase + UCR4);
@@ -942,9 +918,9 @@
writel(num, sport->port.membase + UBIR);
writel(denom, sport->port.membase + UBMR);
-#ifdef ONEMS
- writel(sport->port.uartclk / div / 1000, sport->port.membase + ONEMS);
-#endif
+ if (!cpu_is_mx1())
+ writel(sport->port.uartclk / div / 1000,
+ sport->port.membase + MX2_ONEMS);
writel(old_ucr1, sport->port.membase + UCR1);
@@ -1074,17 +1050,20 @@
imx_console_write(struct console *co, const char *s, unsigned int count)
{
struct imx_port *sport = imx_ports[co->index];
- unsigned int old_ucr1, old_ucr2;
+ unsigned int old_ucr1, old_ucr2, ucr1;
/*
* First, save UCR1/2 and then disable interrupts
*/
- old_ucr1 = readl(sport->port.membase + UCR1);
+ ucr1 = old_ucr1 = readl(sport->port.membase + UCR1);
old_ucr2 = readl(sport->port.membase + UCR2);
- writel((old_ucr1 | UCR1_UARTCLKEN | UCR1_UARTEN) &
- ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN),
- sport->port.membase + UCR1);
+ if (cpu_is_mx1())
+ ucr1 |= MX1_UCR1_UARTCLKEN;
+ ucr1 |= UCR1_UARTEN;
+ ucr1 &= ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN);
+
+ writel(ucr1, sport->port.membase + UCR1);
writel(old_ucr2 | UCR2_TXEN, sport->port.membase + UCR2);