Gitiles
Code Review Sign In
gerrit-public.fairphone.software / kernel / msm / 382b09362711d7d03272230a33767015a277926e / . / drivers / gpu / drm / i915 / i915_reg.h
blob: 88292893b255bf9ffeaf65626ae7329cc3225ca6 [file] [log] [blame]
/* Copyright 2003 Tungsten Graphics, Inc., Cedar Park, Texas.
* All Rights Reserved.
*
* Permission is hereby granted, free of charge, to any person obtaining a
* copy of this software and associated documentation files (the
* "Software"), to deal in the Software without restriction, including
* without limitation the rights to use, copy, modify, merge, publish,
* distribute, sub license, and/or sell copies of the Software, and to
* permit persons to whom the Software is furnished to do so, subject to
* the following conditions:
*
* The above copyright notice and this permission notice (including the
* next paragraph) shall be included in all copies or substantial portions
* of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS
* OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
* IN NO EVENT SHALL TUNGSTEN GRAPHICS AND/OR ITS SUPPLIERS BE LIABLE FOR
* ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
* TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
* SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
*/
#ifndef _I915_REG_H_
#define _I915_REG_H_
#define _PIPE(pipe, a, b) ((a) + (pipe)*((b)-(a)))
/*
* The Bridge device's PCI config space has information about the
* fb aperture size and the amount of pre-reserved memory.
* This is all handled in the intel-gtt.ko module. i915.ko only
* cares about the vga bit for the vga rbiter.
*/
#define INTEL_GMCH_CTRL 0x52
#define INTEL_GMCH_VGA_DISABLE (1 << 1)
/* PCI config space */
#define HPLLCC 0xc0 /* 855 only */
#define GC_CLOCK_CONTROL_MASK (0xf << 0)
#define GC_CLOCK_133_200 (0 << 0)
#define GC_CLOCK_100_200 (1 << 0)
#define GC_CLOCK_100_133 (2 << 0)
#define GC_CLOCK_166_250 (3 << 0)
#define GCFGC2 0xda
#define GCFGC 0xf0 /* 915+ only */
#define GC_LOW_FREQUENCY_ENABLE (1 << 7)
#define GC_DISPLAY_CLOCK_190_200_MHZ (0 << 4)
#define GC_DISPLAY_CLOCK_333_MHZ (4 << 4)
#define GC_DISPLAY_CLOCK_MASK (7 << 4)
#define GM45_GC_RENDER_CLOCK_MASK (0xf << 0)
#define GM45_GC_RENDER_CLOCK_266_MHZ (8 << 0)
#define GM45_GC_RENDER_CLOCK_320_MHZ (9 << 0)
#define GM45_GC_RENDER_CLOCK_400_MHZ (0xb << 0)
#define GM45_GC_RENDER_CLOCK_533_MHZ (0xc << 0)
#define I965_GC_RENDER_CLOCK_MASK (0xf << 0)
#define I965_GC_RENDER_CLOCK_267_MHZ (2 << 0)
#define I965_GC_RENDER_CLOCK_333_MHZ (3 << 0)
#define I965_GC_RENDER_CLOCK_444_MHZ (4 << 0)
#define I965_GC_RENDER_CLOCK_533_MHZ (5 << 0)
#define I945_GC_RENDER_CLOCK_MASK (7 << 0)
#define I945_GC_RENDER_CLOCK_166_MHZ (0 << 0)
#define I945_GC_RENDER_CLOCK_200_MHZ (1 << 0)
#define I945_GC_RENDER_CLOCK_250_MHZ (3 << 0)
#define I945_GC_RENDER_CLOCK_400_MHZ (5 << 0)
#define I915_GC_RENDER_CLOCK_MASK (7 << 0)
#define I915_GC_RENDER_CLOCK_166_MHZ (0 << 0)
#define I915_GC_RENDER_CLOCK_200_MHZ (1 << 0)
#define I915_GC_RENDER_CLOCK_333_MHZ (4 << 0)
#define LBB 0xf4
/* Graphics reset regs */
#define I965_GDRST 0xc0 /* PCI config register */
#define ILK_GDSR 0x2ca4 /* MCHBAR offset */
#define GRDOM_FULL (0<<2)
#define GRDOM_RENDER (1<<2)
#define GRDOM_MEDIA (3<<2)
/* VGA stuff */
#define VGA_ST01_MDA 0x3ba
#define VGA_ST01_CGA 0x3da
#define VGA_MSR_WRITE 0x3c2
#define VGA_MSR_READ 0x3cc
#define VGA_MSR_MEM_EN (1<<1)
#define VGA_MSR_CGA_MODE (1<<0)
#define VGA_SR_INDEX 0x3c4
#define VGA_SR_DATA 0x3c5
#define VGA_AR_INDEX 0x3c0
#define VGA_AR_VID_EN (1<<5)
#define VGA_AR_DATA_WRITE 0x3c0
#define VGA_AR_DATA_READ 0x3c1
#define VGA_GR_INDEX 0x3ce
#define VGA_GR_DATA 0x3cf
/* GR05 */
#define VGA_GR_MEM_READ_MODE_SHIFT 3
#define VGA_GR_MEM_READ_MODE_PLANE 1
/* GR06 */
#define VGA_GR_MEM_MODE_MASK 0xc
#define VGA_GR_MEM_MODE_SHIFT 2
#define VGA_GR_MEM_A0000_AFFFF 0
#define VGA_GR_MEM_A0000_BFFFF 1
#define VGA_GR_MEM_B0000_B7FFF 2
#define VGA_GR_MEM_B0000_BFFFF 3
#define VGA_DACMASK 0x3c6
#define VGA_DACRX 0x3c7
#define VGA_DACWX 0x3c8
#define VGA_DACDATA 0x3c9
#define VGA_CR_INDEX_MDA 0x3b4
#define VGA_CR_DATA_MDA 0x3b5
#define VGA_CR_INDEX_CGA 0x3d4
#define VGA_CR_DATA_CGA 0x3d5
/*
* Memory interface instructions used by the kernel
*/
#define MI_INSTR(opcode, flags) (((opcode) << 23) | (flags))
#define MI_NOOP MI_INSTR(0, 0)
#define MI_USER_INTERRUPT MI_INSTR(0x02, 0)
#define MI_WAIT_FOR_EVENT MI_INSTR(0x03, 0)
#define MI_WAIT_FOR_OVERLAY_FLIP (1<<16)
#define MI_WAIT_FOR_PLANE_B_FLIP (1<<6)
#define MI_WAIT_FOR_PLANE_A_FLIP (1<<2)
#define MI_WAIT_FOR_PLANE_A_SCANLINES (1<<1)
#define MI_FLUSH MI_INSTR(0x04, 0)
#define MI_READ_FLUSH (1 << 0)
#define MI_EXE_FLUSH (1 << 1)
#define MI_NO_WRITE_FLUSH (1 << 2)
#define MI_SCENE_COUNT (1 << 3) /* just increment scene count */
#define MI_END_SCENE (1 << 4) /* flush binner and incr scene count */
#define MI_INVALIDATE_ISP (1 << 5) /* invalidate indirect state pointers */
#define MI_BATCH_BUFFER_END MI_INSTR(0x0a, 0)
#define MI_REPORT_HEAD MI_INSTR(0x07, 0)
#define MI_OVERLAY_FLIP MI_INSTR(0x11,0)
#define MI_OVERLAY_CONTINUE (0x0<<21)
#define MI_OVERLAY_ON (0x1<<21)
#define MI_OVERLAY_OFF (0x2<<21)
#define MI_LOAD_SCAN_LINES_INCL MI_INSTR(0x12, 0)
#define MI_DISPLAY_FLIP MI_INSTR(0x14, 2)
#define MI_DISPLAY_FLIP_I915 MI_INSTR(0x14, 1)
#define MI_DISPLAY_FLIP_PLANE(n) ((n) << 20)
#define MI_SET_CONTEXT MI_INSTR(0x18, 0)
#define MI_MM_SPACE_GTT (1<<8)
#define MI_MM_SPACE_PHYSICAL (0<<8)
#define MI_SAVE_EXT_STATE_EN (1<<3)
#define MI_RESTORE_EXT_STATE_EN (1<<2)
#define MI_RESTORE_INHIBIT (1<<0)
#define MI_STORE_DWORD_IMM MI_INSTR(0x20, 1)
#define MI_MEM_VIRTUAL (1 << 22) /* 965+ only */
#define MI_STORE_DWORD_INDEX MI_INSTR(0x21, 1)
#define MI_STORE_DWORD_INDEX_SHIFT 2
#define MI_LOAD_REGISTER_IMM MI_INSTR(0x22, 1)
#define MI_FLUSH_DW MI_INSTR(0x26, 2) /* for GEN6 */
#define MI_BATCH_BUFFER MI_INSTR(0x30, 1)
#define MI_BATCH_NON_SECURE (1)
#define MI_BATCH_NON_SECURE_I965 (1<<8)
#define MI_BATCH_BUFFER_START MI_INSTR(0x31, 0)
/*
* 3D instructions used by the kernel
*/
#define GFX_INSTR(opcode, flags) ((0x3 << 29) | ((opcode) << 24) | (flags))
#define GFX_OP_RASTER_RULES ((0x3<<29)|(0x7<<24))
#define GFX_OP_SCISSOR ((0x3<<29)|(0x1c<<24)|(0x10<<19))
#define SC_UPDATE_SCISSOR (0x1<<1)
#define SC_ENABLE_MASK (0x1<<0)
#define SC_ENABLE (0x1<<0)
#define GFX_OP_LOAD_INDIRECT ((0x3<<29)|(0x1d<<24)|(0x7<<16))
#define GFX_OP_SCISSOR_INFO ((0x3<<29)|(0x1d<<24)|(0x81<<16)|(0x1))
#define SCI_YMIN_MASK (0xffff<<16)
#define SCI_XMIN_MASK (0xffff<<0)
#define SCI_YMAX_MASK (0xffff<<16)
#define SCI_XMAX_MASK (0xffff<<0)
#define GFX_OP_SCISSOR_ENABLE ((0x3<<29)|(0x1c<<24)|(0x10<<19))
#define GFX_OP_SCISSOR_RECT ((0x3<<29)|(0x1d<<24)|(0x81<<16)|1)
#define GFX_OP_COLOR_FACTOR ((0x3<<29)|(0x1d<<24)|(0x1<<16)|0x0)
#define GFX_OP_STIPPLE ((0x3<<29)|(0x1d<<24)|(0x83<<16))
#define GFX_OP_MAP_INFO ((0x3<<29)|(0x1d<<24)|0x4)
#define GFX_OP_DESTBUFFER_VARS ((0x3<<29)|(0x1d<<24)|(0x85<<16)|0x0)
#define GFX_OP_DESTBUFFER_INFO ((0x3<<29)|(0x1d<<24)|(0x8e<<16)|1)
#define GFX_OP_DRAWRECT_INFO ((0x3<<29)|(0x1d<<24)|(0x80<<16)|(0x3))
#define GFX_OP_DRAWRECT_INFO_I965 ((0x7900<<16)|0x2)
#define SRC_COPY_BLT_CMD ((2<<29)|(0x43<<22)|4)
#define XY_SRC_COPY_BLT_CMD ((2<<29)|(0x53<<22)|6)
#define XY_MONO_SRC_COPY_IMM_BLT ((2<<29)|(0x71<<22)|5)
#define XY_SRC_COPY_BLT_WRITE_ALPHA (1<<21)
#define XY_SRC_COPY_BLT_WRITE_RGB (1<<20)
#define BLT_DEPTH_8 (0<<24)
#define BLT_DEPTH_16_565 (1<<24)
#define BLT_DEPTH_16_1555 (2<<24)
#define BLT_DEPTH_32 (3<<24)
#define BLT_ROP_GXCOPY (0xcc<<16)
#define XY_SRC_COPY_BLT_SRC_TILED (1<<15) /* 965+ only */
#define XY_SRC_COPY_BLT_DST_TILED (1<<11) /* 965+ only */
#define CMD_OP_DISPLAYBUFFER_INFO ((0x0<<29)|(0x14<<23)|2)
#define ASYNC_FLIP (1<<22)
#define DISPLAY_PLANE_A (0<<20)
#define DISPLAY_PLANE_B (1<<20)
#define GFX_OP_PIPE_CONTROL ((0x3<<29)|(0x3<<27)|(0x2<<24)|2)
#define PIPE_CONTROL_QW_WRITE (1<<14)
#define PIPE_CONTROL_DEPTH_STALL (1<<13)
#define PIPE_CONTROL_WC_FLUSH (1<<12)
#define PIPE_CONTROL_IS_FLUSH (1<<11) /* MBZ on Ironlake */
#define PIPE_CONTROL_TC_FLUSH (1<<10) /* GM45+ only */
#define PIPE_CONTROL_ISP_DIS (1<<9)
#define PIPE_CONTROL_NOTIFY (1<<8)
#define PIPE_CONTROL_GLOBAL_GTT (1<<2) /* in addr dword */
#define PIPE_CONTROL_STALL_EN (1<<1) /* in addr word, Ironlake+ only */
/*
* Reset registers
*/
#define DEBUG_RESET_I830 0x6070
#define DEBUG_RESET_FULL (1<<7)
#define DEBUG_RESET_RENDER (1<<8)
#define DEBUG_RESET_DISPLAY (1<<9)
/*
* Fence registers
*/
#define FENCE_REG_830_0 0x2000
#define FENCE_REG_945_8 0x3000
#define I830_FENCE_START_MASK 0x07f80000
#define I830_FENCE_TILING_Y_SHIFT 12
#define I830_FENCE_SIZE_BITS(size) ((ffs((size) >> 19) - 1) << 8)
#define I830_FENCE_PITCH_SHIFT 4
#define I830_FENCE_REG_VALID (1<<0)
#define I915_FENCE_MAX_PITCH_VAL 4
#define I830_FENCE_MAX_PITCH_VAL 6
#define I830_FENCE_MAX_SIZE_VAL (1<<8)
#define I915_FENCE_START_MASK 0x0ff00000
#define I915_FENCE_SIZE_BITS(size) ((ffs((size) >> 20) - 1) << 8)
#define FENCE_REG_965_0 0x03000
#define I965_FENCE_PITCH_SHIFT 2
#define I965_FENCE_TILING_Y_SHIFT 1
#define I965_FENCE_REG_VALID (1<<0)
#define I965_FENCE_MAX_PITCH_VAL 0x0400
#define FENCE_REG_SANDYBRIDGE_0 0x100000
#define SANDYBRIDGE_FENCE_PITCH_SHIFT 32
/*
* Instruction and interrupt control regs
*/
#define PGTBL_ER 0x02024
#define PRB0_TAIL 0x02030
#define PRB0_HEAD 0x02034
#define PRB0_START 0x02038
#define PRB0_CTL 0x0203c
#define RENDER_RING_BASE 0x02000
#define BSD_RING_BASE 0x04000
#define GEN6_BSD_RING_BASE 0x12000
#define RING_TAIL(base) ((base)+0x30)
#define RING_HEAD(base) ((base)+0x34)
#define RING_START(base) ((base)+0x38)
#define RING_CTL(base) ((base)+0x3c)
#define RING_HWS_PGA(base) ((base)+0x80)
#define RING_HWS_PGA_GEN6(base) ((base)+0x2080)
#define RING_ACTHD(base) ((base)+0x74)
#define TAIL_ADDR 0x001FFFF8
#define HEAD_WRAP_COUNT 0xFFE00000
#define HEAD_WRAP_ONE 0x00200000
#define HEAD_ADDR 0x001FFFFC
#define RING_NR_PAGES 0x001FF000
#define RING_REPORT_MASK 0x00000006
#define RING_REPORT_64K 0x00000002
#define RING_REPORT_128K 0x00000004
#define RING_NO_REPORT 0x00000000
#define RING_VALID_MASK 0x00000001
#define RING_VALID 0x00000001
#define RING_INVALID 0x00000000
#define RING_WAIT_I8XX (1<<0) /* gen2, PRBx_HEAD */
#define RING_WAIT (1<<11) /* gen3+, PRBx_CTL */
#define PRB1_TAIL 0x02040 /* 915+ only */
#define PRB1_HEAD 0x02044 /* 915+ only */
#define PRB1_START 0x02048 /* 915+ only */
#define PRB1_CTL 0x0204c /* 915+ only */
#define IPEIR_I965 0x02064
#define IPEHR_I965 0x02068
#define INSTDONE_I965 0x0206c
#define INSTPS 0x02070 /* 965+ only */
#define INSTDONE1 0x0207c /* 965+ only */
#define ACTHD_I965 0x02074
#define HWS_PGA 0x02080
#define HWS_ADDRESS_MASK 0xfffff000
#define HWS_START_ADDRESS_SHIFT 4
#define PWRCTXA 0x2088 /* 965GM+ only */
#define PWRCTX_EN (1<<0)
#define IPEIR 0x02088
#define IPEHR 0x0208c
#define INSTDONE 0x02090
#define NOPID 0x02094
#define HWSTAM 0x02098
#define MI_MODE 0x0209c
# define VS_TIMER_DISPATCH (1 << 6)
# define MI_FLUSH_ENABLE (1 << 11)
#define SCPD0 0x0209c /* 915+ only */
#define IER 0x020a0
#define IIR 0x020a4
#define IMR 0x020a8
#define ISR 0x020ac
#define I915_PIPE_CONTROL_NOTIFY_INTERRUPT (1<<18)
#define I915_DISPLAY_PORT_INTERRUPT (1<<17)
#define I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT (1<<15)
#define I915_GMCH_THERMAL_SENSOR_EVENT_INTERRUPT (1<<14) /* p-state */
#define I915_HWB_OOM_INTERRUPT (1<<13)
#define I915_SYNC_STATUS_INTERRUPT (1<<12)
#define I915_DISPLAY_PLANE_A_FLIP_PENDING_INTERRUPT (1<<11)
#define I915_DISPLAY_PLANE_B_FLIP_PENDING_INTERRUPT (1<<10)
#define I915_OVERLAY_PLANE_FLIP_PENDING_INTERRUPT (1<<9)
#define I915_DISPLAY_PLANE_C_FLIP_PENDING_INTERRUPT (1<<8)
#define I915_DISPLAY_PIPE_A_VBLANK_INTERRUPT (1<<7)
#define I915_DISPLAY_PIPE_A_EVENT_INTERRUPT (1<<6)
#define I915_DISPLAY_PIPE_B_VBLANK_INTERRUPT (1<<5)
#define I915_DISPLAY_PIPE_B_EVENT_INTERRUPT (1<<4)
#define I915_DEBUG_INTERRUPT (1<<2)
#define I915_USER_INTERRUPT (1<<1)
#define I915_ASLE_INTERRUPT (1<<0)
#define I915_BSD_USER_INTERRUPT (1<<25)
#define EIR 0x020b0
#define EMR 0x020b4
#define ESR 0x020b8
#define GM45_ERROR_PAGE_TABLE (1<<5)
#define GM45_ERROR_MEM_PRIV (1<<4)
#define I915_ERROR_PAGE_TABLE (1<<4)
#define GM45_ERROR_CP_PRIV (1<<3)
#define I915_ERROR_MEMORY_REFRESH (1<<1)
#define I915_ERROR_INSTRUCTION (1<<0)
#define INSTPM 0x020c0
#define INSTPM_SELF_EN (1<<12) /* 915GM only */
#define ACTHD 0x020c8
#define FW_BLC 0x020d8
#define FW_BLC2 0x020dc
#define FW_BLC_SELF 0x020e0 /* 915+ only */
#define FW_BLC_SELF_EN_MASK (1<<31)
#define FW_BLC_SELF_FIFO_MASK (1<<16) /* 945 only */
#define FW_BLC_SELF_EN (1<<15) /* 945 only */
#define MM_BURST_LENGTH 0x00700000
#define MM_FIFO_WATERMARK 0x0001F000
#define LM_BURST_LENGTH 0x00000700
#define LM_FIFO_WATERMARK 0x0000001F
#define MI_ARB_STATE 0x020e4 /* 915+ only */
#define MI_ARB_MASK_SHIFT 16 /* shift for enable bits */
/* Make render/texture TLB fetches lower priorty than associated data
* fetches. This is not turned on by default
*/
#define MI_ARB_RENDER_TLB_LOW_PRIORITY (1 << 15)
/* Isoch request wait on GTT enable (Display A/B/C streams).
* Make isoch requests stall on the TLB update. May cause
* display underruns (test mode only)
*/
#define MI_ARB_ISOCH_WAIT_GTT (1 << 14)
/* Block grant count for isoch requests when block count is
* set to a finite value.
*/
#define MI_ARB_BLOCK_GRANT_MASK (3 << 12)
#define MI_ARB_BLOCK_GRANT_8 (0 << 12) /* for 3 display planes */
#define MI_ARB_BLOCK_GRANT_4 (1 << 12) /* for 2 display planes */
#define MI_ARB_BLOCK_GRANT_2 (2 << 12) /* for 1 display plane */
#define MI_ARB_BLOCK_GRANT_0 (3 << 12) /* don't use */
/* Enable render writes to complete in C2/C3/C4 power states.
* If this isn't enabled, render writes are prevented in low
* power states. That seems bad to me.
*/
#define MI_ARB_C3_LP_WRITE_ENABLE (1 << 11)
/* This acknowledges an async flip immediately instead
* of waiting for 2TLB fetches.
*/
#define MI_ARB_ASYNC_FLIP_ACK_IMMEDIATE (1 << 10)
/* Enables non-sequential data reads through arbiter
*/
#define MI_ARB_DUAL_DATA_PHASE_DISABLE (1 << 9)
/* Disable FSB snooping of cacheable write cycles from binner/render
* command stream
*/
#define MI_ARB_CACHE_SNOOP_DISABLE (1 << 8)
/* Arbiter time slice for non-isoch streams */
#define MI_ARB_TIME_SLICE_MASK (7 << 5)
#define MI_ARB_TIME_SLICE_1 (0 << 5)
#define MI_ARB_TIME_SLICE_2 (1 << 5)
#define MI_ARB_TIME_SLICE_4 (2 << 5)
#define MI_ARB_TIME_SLICE_6 (3 << 5)
#define MI_ARB_TIME_SLICE_8 (4 << 5)
#define MI_ARB_TIME_SLICE_10 (5 << 5)
#define MI_ARB_TIME_SLICE_14 (6 << 5)
#define MI_ARB_TIME_SLICE_16 (7 << 5)
/* Low priority grace period page size */
#define MI_ARB_LOW_PRIORITY_GRACE_4KB (0 << 4) /* default */
#define MI_ARB_LOW_PRIORITY_GRACE_8KB (1 << 4)
/* Disable display A/B trickle feed */
#define MI_ARB_DISPLAY_TRICKLE_FEED_DISABLE (1 << 2)
/* Set display plane priority */
#define MI_ARB_DISPLAY_PRIORITY_A_B (0 << 0) /* display A > display B */
#define MI_ARB_DISPLAY_PRIORITY_B_A (1 << 0) /* display B > display A */
#define CACHE_MODE_0 0x02120 /* 915+ only */
#define CM0_MASK_SHIFT 16
#define CM0_IZ_OPT_DISABLE (1<<6)
#define CM0_ZR_OPT_DISABLE (1<<5)
#define CM0_DEPTH_EVICT_DISABLE (1<<4)
#define CM0_COLOR_EVICT_DISABLE (1<<3)
#define CM0_DEPTH_WRITE_DISABLE (1<<1)
#define CM0_RC_OP_FLUSH_DISABLE (1<<0)
#define BB_ADDR 0x02140 /* 8 bytes */
#define GFX_FLSH_CNTL 0x02170 /* 915+ only */
#define ECOSKPD 0x021d0
#define ECO_GATING_CX_ONLY (1<<3)
#define ECO_FLIP_DONE (1<<0)
/* GEN6 interrupt control */
#define GEN6_RENDER_HWSTAM 0x2098
#define GEN6_RENDER_IMR 0x20a8
#define GEN6_RENDER_CONTEXT_SWITCH_INTERRUPT (1 << 8)
#define GEN6_RENDER_PPGTT_PAGE_FAULT (1 << 7)
#define GEN6_RENDER_TIMEOUT_COUNTER_EXPIRED (1 << 6)
#define GEN6_RENDER_L3_PARITY_ERROR (1 << 5)
#define GEN6_RENDER_PIPE_CONTROL_NOTIFY_INTERRUPT (1 << 4)
#define GEN6_RENDER_COMMAND_PARSER_MASTER_ERROR (1 << 3)
#define GEN6_RENDER_SYNC_STATUS (1 << 2)
#define GEN6_RENDER_DEBUG_INTERRUPT (1 << 1)
#define GEN6_RENDER_USER_INTERRUPT (1 << 0)
#define GEN6_BLITTER_HWSTAM 0x22098
#define GEN6_BLITTER_IMR 0x220a8
#define GEN6_BLITTER_MI_FLUSH_DW_NOTIFY_INTERRUPT (1 << 26)
#define GEN6_BLITTER_COMMAND_PARSER_MASTER_ERROR (1 << 25)
#define GEN6_BLITTER_SYNC_STATUS (1 << 24)
#define GEN6_BLITTER_USER_INTERRUPT (1 << 22)
#define GEN6_BSD_SLEEP_PSMI_CONTROL 0x12050
#define GEN6_BSD_SLEEP_PSMI_CONTROL_RC_ILDL_MESSAGE_MODIFY_MASK (1 << 16)
#define GEN6_BSD_SLEEP_PSMI_CONTROL_RC_ILDL_MESSAGE_DISABLE (1 << 0)
#define GEN6_BSD_SLEEP_PSMI_CONTROL_RC_ILDL_MESSAGE_ENABLE 0
#define GEN6_BSD_SLEEP_PSMI_CONTROL_IDLE_INDICATOR (1 << 3)
#define GEN6_BSD_IMR 0x120a8
#define GEN6_BSD_IMR_USER_INTERRUPT (1 << 12)
#define GEN6_BSD_RNCID 0x12198
/*
* Framebuffer compression (915+ only)
*/
#define FBC_CFB_BASE 0x03200 /* 4k page aligned */
#define FBC_LL_BASE 0x03204 /* 4k page aligned */
#define FBC_CONTROL 0x03208
#define FBC_CTL_EN (1<<31)
#define FBC_CTL_PERIODIC (1<<30)
#define FBC_CTL_INTERVAL_SHIFT (16)
#define FBC_CTL_UNCOMPRESSIBLE (1<<14)
#define FBC_CTL_C3_IDLE (1<<13)
#define FBC_CTL_STRIDE_SHIFT (5)
#define FBC_CTL_FENCENO (1<<0)
#define FBC_COMMAND 0x0320c
#define FBC_CMD_COMPRESS (1<<0)
#define FBC_STATUS 0x03210
#define FBC_STAT_COMPRESSING (1<<31)
#define FBC_STAT_COMPRESSED (1<<30)
#define FBC_STAT_MODIFIED (1<<29)
#define FBC_STAT_CURRENT_LINE (1<<0)
#define FBC_CONTROL2 0x03214
#define FBC_CTL_FENCE_DBL (0<<4)
#define FBC_CTL_IDLE_IMM (0<<2)
#define FBC_CTL_IDLE_FULL (1<<2)
#define FBC_CTL_IDLE_LINE (2<<2)
#define FBC_CTL_IDLE_DEBUG (3<<2)
#define FBC_CTL_CPU_FENCE (1<<1)
#define FBC_CTL_PLANEA (0<<0)
#define FBC_CTL_PLANEB (1<<0)
#define FBC_FENCE_OFF 0x0321b
#define FBC_TAG 0x03300
#define FBC_LL_SIZE (1536)
/* Framebuffer compression for GM45+ */
#define DPFC_CB_BASE 0x3200
#define DPFC_CONTROL 0x3208
#define DPFC_CTL_EN (1<<31)
#define DPFC_CTL_PLANEA (0<<30)
#define DPFC_CTL_PLANEB (1<<30)
#define DPFC_CTL_FENCE_EN (1<<29)
#define DPFC_SR_EN (1<<10)
#define DPFC_CTL_LIMIT_1X (0<<6)
#define DPFC_CTL_LIMIT_2X (1<<6)
#define DPFC_CTL_LIMIT_4X (2<<6)
#define DPFC_RECOMP_CTL 0x320c
#define DPFC_RECOMP_STALL_EN (1<<27)
#define DPFC_RECOMP_STALL_WM_SHIFT (16)
#define DPFC_RECOMP_STALL_WM_MASK (0x07ff0000)
#define DPFC_RECOMP_TIMER_COUNT_SHIFT (0)
#define DPFC_RECOMP_TIMER_COUNT_MASK (0x0000003f)
#define DPFC_STATUS 0x3210
#define DPFC_INVAL_SEG_SHIFT (16)
#define DPFC_INVAL_SEG_MASK (0x07ff0000)
#define DPFC_COMP_SEG_SHIFT (0)
#define DPFC_COMP_SEG_MASK (0x000003ff)
#define DPFC_STATUS2 0x3214
#define DPFC_FENCE_YOFF 0x3218
#define DPFC_CHICKEN 0x3224
#define DPFC_HT_MODIFY (1<<31)
/* Framebuffer compression for Ironlake */
#define ILK_DPFC_CB_BASE 0x43200
#define ILK_DPFC_CONTROL 0x43208
/* The bit 28-8 is reserved */
#define DPFC_RESERVED (0x1FFFFF00)
#define ILK_DPFC_RECOMP_CTL 0x4320c
#define ILK_DPFC_STATUS 0x43210
#define ILK_DPFC_FENCE_YOFF 0x43218
#define ILK_DPFC_CHICKEN 0x43224
#define ILK_FBC_RT_BASE 0x2128
#define ILK_FBC_RT_VALID (1<<0)
#define ILK_DISPLAY_CHICKEN1 0x42000
#define ILK_FBCQ_DIS (1<<22)
/*
* GPIO regs
*/
#define GPIOA 0x5010
#define GPIOB 0x5014
#define GPIOC 0x5018
#define GPIOD 0x501c
#define GPIOE 0x5020
#define GPIOF 0x5024
#define GPIOG 0x5028
#define GPIOH 0x502c
# define GPIO_CLOCK_DIR_MASK (1 << 0)
# define GPIO_CLOCK_DIR_IN (0 << 1)
# define GPIO_CLOCK_DIR_OUT (1 << 1)
# define GPIO_CLOCK_VAL_MASK (1 << 2)
# define GPIO_CLOCK_VAL_OUT (1 << 3)
# define GPIO_CLOCK_VAL_IN (1 << 4)
# define GPIO_CLOCK_PULLUP_DISABLE (1 << 5)
# define GPIO_DATA_DIR_MASK (1 << 8)
# define GPIO_DATA_DIR_IN (0 << 9)
# define GPIO_DATA_DIR_OUT (1 << 9)
# define GPIO_DATA_VAL_MASK (1 << 10)
# define GPIO_DATA_VAL_OUT (1 << 11)
# define GPIO_DATA_VAL_IN (1 << 12)
# define GPIO_DATA_PULLUP_DISABLE (1 << 13)
#define GMBUS0 0x5100 /* clock/port select */
#define GMBUS_RATE_100KHZ (0<<8)
#define GMBUS_RATE_50KHZ (1<<8)
#define GMBUS_RATE_400KHZ (2<<8) /* reserved on Pineview */
#define GMBUS_RATE_1MHZ (3<<8) /* reserved on Pineview */
#define GMBUS_HOLD_EXT (1<<7) /* 300ns hold time, rsvd on Pineview */
#define GMBUS_PORT_DISABLED 0
#define GMBUS_PORT_SSC 1
#define GMBUS_PORT_VGADDC 2
#define GMBUS_PORT_PANEL 3
#define GMBUS_PORT_DPC 4 /* HDMIC */
#define GMBUS_PORT_DPB 5 /* SDVO, HDMIB */
/* 6 reserved */
#define GMBUS_PORT_DPD 7 /* HDMID */
#define GMBUS_NUM_PORTS 8
#define GMBUS1 0x5104 /* command/status */
#define GMBUS_SW_CLR_INT (1<<31)
#define GMBUS_SW_RDY (1<<30)
#define GMBUS_ENT (1<<29) /* enable timeout */
#define GMBUS_CYCLE_NONE (0<<25)
#define GMBUS_CYCLE_WAIT (1<<25)
#define GMBUS_CYCLE_INDEX (2<<25)
#define GMBUS_CYCLE_STOP (4<<25)
#define GMBUS_BYTE_COUNT_SHIFT 16
#define GMBUS_SLAVE_INDEX_SHIFT 8
#define GMBUS_SLAVE_ADDR_SHIFT 1
#define GMBUS_SLAVE_READ (1<<0)
#define GMBUS_SLAVE_WRITE (0<<0)
#define GMBUS2 0x5108 /* status */
#define GMBUS_INUSE (1<<15)
#define GMBUS_HW_WAIT_PHASE (1<<14)
#define GMBUS_STALL_TIMEOUT (1<<13)
#define GMBUS_INT (1<<12)
#define GMBUS_HW_RDY (1<<11)
#define GMBUS_SATOER (1<<10)
#define GMBUS_ACTIVE (1<<9)
#define GMBUS3 0x510c /* data buffer bytes 3-0 */
#define GMBUS4 0x5110 /* interrupt mask (Pineview+) */
#define GMBUS_SLAVE_TIMEOUT_EN (1<<4)
#define GMBUS_NAK_EN (1<<3)
#define GMBUS_IDLE_EN (1<<2)
#define GMBUS_HW_WAIT_EN (1<<1)
#define GMBUS_HW_RDY_EN (1<<0)
#define GMBUS5 0x5120 /* byte index */
#define GMBUS_2BYTE_INDEX_EN (1<<31)
/*
* Clock control & power management
*/
#define VGA0 0x6000
#define VGA1 0x6004
#define VGA_PD 0x6010
#define VGA0_PD_P2_DIV_4 (1 << 7)
#define VGA0_PD_P1_DIV_2 (1 << 5)
#define VGA0_PD_P1_SHIFT 0
#define VGA0_PD_P1_MASK (0x1f << 0)
#define VGA1_PD_P2_DIV_4 (1 << 15)
#define VGA1_PD_P1_DIV_2 (1 << 13)
#define VGA1_PD_P1_SHIFT 8
#define VGA1_PD_P1_MASK (0x1f << 8)
#define DPLL_A 0x06014
#define DPLL_B 0x06018
#define DPLL(pipe) _PIPE(pipe, DPLL_A, DPLL_B)
#define DPLL_VCO_ENABLE (1 << 31)
#define DPLL_DVO_HIGH_SPEED (1 << 30)
#define DPLL_SYNCLOCK_ENABLE (1 << 29)
#define DPLL_VGA_MODE_DIS (1 << 28)
#define DPLLB_MODE_DAC_SERIAL (1 << 26) /* i915 */
#define DPLLB_MODE_LVDS (2 << 26) /* i915 */
#define DPLL_MODE_MASK (3 << 26)
#define DPLL_DAC_SERIAL_P2_CLOCK_DIV_10 (0 << 24) /* i915 */
#define DPLL_DAC_SERIAL_P2_CLOCK_DIV_5 (1 << 24) /* i915 */
#define DPLLB_LVDS_P2_CLOCK_DIV_14 (0 << 24) /* i915 */
#define DPLLB_LVDS_P2_CLOCK_DIV_7 (1 << 24) /* i915 */
#define DPLL_P2_CLOCK_DIV_MASK 0x03000000 /* i915 */
#define DPLL_FPA01_P1_POST_DIV_MASK 0x00ff0000 /* i915 */
#define DPLL_FPA01_P1_POST_DIV_MASK_PINEVIEW 0x00ff8000 /* Pineview */
#define SRX_INDEX 0x3c4
#define SRX_DATA 0x3c5
#define SR01 1
#define SR01_SCREEN_OFF (1<<5)
#define PPCR 0x61204
#define PPCR_ON (1<<0)
#define DVOB 0x61140
#define DVOB_ON (1<<31)
#define DVOC 0x61160
#define DVOC_ON (1<<31)
#define LVDS 0x61180
#define LVDS_ON (1<<31)
#define ADPA 0x61100
#define ADPA_DPMS_MASK (~(3<<10))
#define ADPA_DPMS_ON (0<<10)
#define ADPA_DPMS_SUSPEND (1<<10)
#define ADPA_DPMS_STANDBY (2<<10)
#define ADPA_DPMS_OFF (3<<10)
/* Scratch pad debug 0 reg:
*/
#define DPLL_FPA01_P1_POST_DIV_MASK_I830 0x001f0000
/*
* The i830 generation, in LVDS mode, defines P1 as the bit number set within
* this field (only one bit may be set).
*/
#define DPLL_FPA01_P1_POST_DIV_MASK_I830_LVDS 0x003f0000
#define DPLL_FPA01_P1_POST_DIV_SHIFT 16
#define DPLL_FPA01_P1_POST_DIV_SHIFT_PINEVIEW 15
/* i830, required in DVO non-gang */
#define PLL_P2_DIVIDE_BY_4 (1 << 23)
#define PLL_P1_DIVIDE_BY_TWO (1 << 21) /* i830 */
#define PLL_REF_INPUT_DREFCLK (0 << 13)
#define PLL_REF_INPUT_TVCLKINA (1 << 13) /* i830 */
#define PLL_REF_INPUT_TVCLKINBC (2 << 13) /* SDVO TVCLKIN */
#define PLLB_REF_INPUT_SPREADSPECTRUMIN (3 << 13)
#define PLL_REF_INPUT_MASK (3 << 13)
#define PLL_LOAD_PULSE_PHASE_SHIFT 9
/* Ironlake */
# define PLL_REF_SDVO_HDMI_MULTIPLIER_SHIFT 9
# define PLL_REF_SDVO_HDMI_MULTIPLIER_MASK (7 << 9)
# define PLL_REF_SDVO_HDMI_MULTIPLIER(x) (((x)-1) << 9)
# define DPLL_FPA1_P1_POST_DIV_SHIFT 0
# define DPLL_FPA1_P1_POST_DIV_MASK 0xff
/*
* Parallel to Serial Load Pulse phase selection.
* Selects the phase for the 10X DPLL clock for the PCIe
* digital display port. The range is 4 to 13; 10 or more
* is just a flip delay. The default is 6
*/
#define PLL_LOAD_PULSE_PHASE_MASK (0xf << PLL_LOAD_PULSE_PHASE_SHIFT)
#define DISPLAY_RATE_SELECT_FPA1 (1 << 8)
/*
* SDVO multiplier for 945G/GM. Not used on 965.
*/
#define SDVO_MULTIPLIER_MASK 0x000000ff
#define SDVO_MULTIPLIER_SHIFT_HIRES 4
#define SDVO_MULTIPLIER_SHIFT_VGA 0
#define DPLL_A_MD 0x0601c /* 965+ only */
/*
* UDI pixel divider, controlling how many pixels are stuffed into a packet.
*
* Value is pixels minus 1. Must be set to 1 pixel for SDVO.
*/
#define DPLL_MD_UDI_DIVIDER_MASK 0x3f000000
#define DPLL_MD_UDI_DIVIDER_SHIFT 24
/* UDI pixel divider for VGA, same as DPLL_MD_UDI_DIVIDER_MASK. */
#define DPLL_MD_VGA_UDI_DIVIDER_MASK 0x003f0000
#define DPLL_MD_VGA_UDI_DIVIDER_SHIFT 16
/*
* SDVO/UDI pixel multiplier.
*
* SDVO requires that the bus clock rate be between 1 and 2 Ghz, and the bus
* clock rate is 10 times the DPLL clock. At low resolution/refresh rate
* modes, the bus rate would be below the limits, so SDVO allows for stuffing
* dummy bytes in the datastream at an increased clock rate, with both sides of
* the link knowing how many bytes are fill.
*
* So, for a mode with a dotclock of 65Mhz, we would want to double the clock
* rate to 130Mhz to get a bus rate of 1.30Ghz. The DPLL clock rate would be
* set to 130Mhz, and the SDVO multiplier set to 2x in this register and
* through an SDVO command.
*
* This register field has values of multiplication factor minus 1, with
* a maximum multiplier of 5 for SDVO.
*/
#define DPLL_MD_UDI_MULTIPLIER_MASK 0x00003f00
#define DPLL_MD_UDI_MULTIPLIER_SHIFT 8
/*
* SDVO/UDI pixel multiplier for VGA, same as DPLL_MD_UDI_MULTIPLIER_MASK.
* This best be set to the default value (3) or the CRT won't work. No,
* I don't entirely understand what this does...
*/
#define DPLL_MD_VGA_UDI_MULTIPLIER_MASK 0x0000003f
#define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0
#define DPLL_B_MD 0x06020 /* 965+ only */
#define DPLL_MD(pipe) _PIPE(pipe, DPLL_A_MD, DPLL_B_MD)
#define FPA0 0x06040
#define FPA1 0x06044
#define FPB0 0x06048
#define FPB1 0x0604c
#define FP0(pipe) _PIPE(pipe, FPA0, FPB0)
#define FP1(pipe) _PIPE(pipe, FPA1, FPB1)
#define FP_N_DIV_MASK 0x003f0000
#define FP_N_PINEVIEW_DIV_MASK 0x00ff0000
#define FP_N_DIV_SHIFT 16
#define FP_M1_DIV_MASK 0x00003f00
#define FP_M1_DIV_SHIFT 8
#define FP_M2_DIV_MASK 0x0000003f
#define FP_M2_PINEVIEW_DIV_MASK 0x000000ff
#define FP_M2_DIV_SHIFT 0
#define DPLL_TEST 0x606c
#define DPLLB_TEST_SDVO_DIV_1 (0 << 22)
#define DPLLB_TEST_SDVO_DIV_2 (1 << 22)
#define DPLLB_TEST_SDVO_DIV_4 (2 << 22)
#define DPLLB_TEST_SDVO_DIV_MASK (3 << 22)
#define DPLLB_TEST_N_BYPASS (1 << 19)
#define DPLLB_TEST_M_BYPASS (1 << 18)
#define DPLLB_INPUT_BUFFER_ENABLE (1 << 16)
#define DPLLA_TEST_N_BYPASS (1 << 3)
#define DPLLA_TEST_M_BYPASS (1 << 2)
#define DPLLA_INPUT_BUFFER_ENABLE (1 << 0)
#define D_STATE 0x6104
#define DSTATE_GFX_RESET_I830 (1<<6)
#define DSTATE_PLL_D3_OFF (1<<3)
#define DSTATE_GFX_CLOCK_GATING (1<<1)
#define DSTATE_DOT_CLOCK_GATING (1<<0)
#define DSPCLK_GATE_D 0x6200
# define DPUNIT_B_CLOCK_GATE_DISABLE (1 << 30) /* 965 */
# define VSUNIT_CLOCK_GATE_DISABLE (1 << 29) /* 965 */
# define VRHUNIT_CLOCK_GATE_DISABLE (1 << 28) /* 965 */
# define VRDUNIT_CLOCK_GATE_DISABLE (1 << 27) /* 965 */
# define AUDUNIT_CLOCK_GATE_DISABLE (1 << 26) /* 965 */
# define DPUNIT_A_CLOCK_GATE_DISABLE (1 << 25) /* 965 */
# define DPCUNIT_CLOCK_GATE_DISABLE (1 << 24) /* 965 */
# define TVRUNIT_CLOCK_GATE_DISABLE (1 << 23) /* 915-945 */
# define TVCUNIT_CLOCK_GATE_DISABLE (1 << 22) /* 915-945 */
# define TVFUNIT_CLOCK_GATE_DISABLE (1 << 21) /* 915-945 */
# define TVEUNIT_CLOCK_GATE_DISABLE (1 << 20) /* 915-945 */
# define DVSUNIT_CLOCK_GATE_DISABLE (1 << 19) /* 915-945 */
# define DSSUNIT_CLOCK_GATE_DISABLE (1 << 18) /* 915-945 */
# define DDBUNIT_CLOCK_GATE_DISABLE (1 << 17) /* 915-945 */
# define DPRUNIT_CLOCK_GATE_DISABLE (1 << 16) /* 915-945 */
# define DPFUNIT_CLOCK_GATE_DISABLE (1 << 15) /* 915-945 */
# define DPBMUNIT_CLOCK_GATE_DISABLE (1 << 14) /* 915-945 */
# define DPLSUNIT_CLOCK_GATE_DISABLE (1 << 13) /* 915-945 */
# define DPLUNIT_CLOCK_GATE_DISABLE (1 << 12) /* 915-945 */
# define DPOUNIT_CLOCK_GATE_DISABLE (1 << 11)
# define DPBUNIT_CLOCK_GATE_DISABLE (1 << 10)
# define DCUNIT_CLOCK_GATE_DISABLE (1 << 9)
# define DPUNIT_CLOCK_GATE_DISABLE (1 << 8)
# define VRUNIT_CLOCK_GATE_DISABLE (1 << 7) /* 915+: reserved */
# define OVHUNIT_CLOCK_GATE_DISABLE (1 << 6) /* 830-865 */
# define DPIOUNIT_CLOCK_GATE_DISABLE (1 << 6) /* 915-945 */
# define OVFUNIT_CLOCK_GATE_DISABLE (1 << 5)
# define OVBUNIT_CLOCK_GATE_DISABLE (1 << 4)
/**
* This bit must be set on the 830 to prevent hangs when turning off the
* overlay scaler.
*/
# define OVRUNIT_CLOCK_GATE_DISABLE (1 << 3)
# define OVCUNIT_CLOCK_GATE_DISABLE (1 << 2)
# define OVUUNIT_CLOCK_GATE_DISABLE (1 << 1)
# define ZVUNIT_CLOCK_GATE_DISABLE (1 << 0) /* 830 */
# define OVLUNIT_CLOCK_GATE_DISABLE (1 << 0) /* 845,865 */
#define RENCLK_GATE_D1 0x6204
# define BLITTER_CLOCK_GATE_DISABLE (1 << 13) /* 945GM only */
# define MPEG_CLOCK_GATE_DISABLE (1 << 12) /* 945GM only */
# define PC_FE_CLOCK_GATE_DISABLE (1 << 11)
# define PC_BE_CLOCK_GATE_DISABLE (1 << 10)
# define WINDOWER_CLOCK_GATE_DISABLE (1 << 9)
# define INTERPOLATOR_CLOCK_GATE_DISABLE (1 << 8)
# define COLOR_CALCULATOR_CLOCK_GATE_DISABLE (1 << 7)
# define MOTION_COMP_CLOCK_GATE_DISABLE (1 << 6)
# define MAG_CLOCK_GATE_DISABLE (1 << 5)
/** This bit must be unset on 855,865 */
# define MECI_CLOCK_GATE_DISABLE (1 << 4)
# define DCMP_CLOCK_GATE_DISABLE (1 << 3)
# define MEC_CLOCK_GATE_DISABLE (1 << 2)
# define MECO_CLOCK_GATE_DISABLE (1 << 1)
/** This bit must be set on 855,865. */
# define SV_CLOCK_GATE_DISABLE (1 << 0)
# define I915_MPEG_CLOCK_GATE_DISABLE (1 << 16)
# define I915_VLD_IP_PR_CLOCK_GATE_DISABLE (1 << 15)
# define I915_MOTION_COMP_CLOCK_GATE_DISABLE (1 << 14)
# define I915_BD_BF_CLOCK_GATE_DISABLE (1 << 13)
# define I915_SF_SE_CLOCK_GATE_DISABLE (1 << 12)
# define I915_WM_CLOCK_GATE_DISABLE (1 << 11)
# define I915_IZ_CLOCK_GATE_DISABLE (1 << 10)
# define I915_PI_CLOCK_GATE_DISABLE (1 << 9)
# define I915_DI_CLOCK_GATE_DISABLE (1 << 8)
# define I915_SH_SV_CLOCK_GATE_DISABLE (1 << 7)
# define I915_PL_DG_QC_FT_CLOCK_GATE_DISABLE (1 << 6)
# define I915_SC_CLOCK_GATE_DISABLE (1 << 5)
# define I915_FL_CLOCK_GATE_DISABLE (1 << 4)
# define I915_DM_CLOCK_GATE_DISABLE (1 << 3)
# define I915_PS_CLOCK_GATE_DISABLE (1 << 2)
# define I915_CC_CLOCK_GATE_DISABLE (1 << 1)
# define I915_BY_CLOCK_GATE_DISABLE (1 << 0)
# define I965_RCZ_CLOCK_GATE_DISABLE (1 << 30)
/** This bit must always be set on 965G/965GM */
# define I965_RCC_CLOCK_GATE_DISABLE (1 << 29)
# define I965_RCPB_CLOCK_GATE_DISABLE (1 << 28)
# define I965_DAP_CLOCK_GATE_DISABLE (1 << 27)
# define I965_ROC_CLOCK_GATE_DISABLE (1 << 26)
# define I965_GW_CLOCK_GATE_DISABLE (1 << 25)
# define I965_TD_CLOCK_GATE_DISABLE (1 << 24)
/** This bit must always be set on 965G */
# define I965_ISC_CLOCK_GATE_DISABLE (1 << 23)
# define I965_IC_CLOCK_GATE_DISABLE (1 << 22)
# define I965_EU_CLOCK_GATE_DISABLE (1 << 21)
# define I965_IF_CLOCK_GATE_DISABLE (1 << 20)
# define I965_TC_CLOCK_GATE_DISABLE (1 << 19)
# define I965_SO_CLOCK_GATE_DISABLE (1 << 17)
# define I965_FBC_CLOCK_GATE_DISABLE (1 << 16)
# define I965_MARI_CLOCK_GATE_DISABLE (1 << 15)
# define I965_MASF_CLOCK_GATE_DISABLE (1 << 14)
# define I965_MAWB_CLOCK_GATE_DISABLE (1 << 13)
# define I965_EM_CLOCK_GATE_DISABLE (1 << 12)
# define I965_UC_CLOCK_GATE_DISABLE (1 << 11)
# define I965_SI_CLOCK_GATE_DISABLE (1 << 6)
# define I965_MT_CLOCK_GATE_DISABLE (1 << 5)
# define I965_PL_CLOCK_GATE_DISABLE (1 << 4)
# define I965_DG_CLOCK_GATE_DISABLE (1 << 3)
# define I965_QC_CLOCK_GATE_DISABLE (1 << 2)
# define I965_FT_CLOCK_GATE_DISABLE (1 << 1)
# define I965_DM_CLOCK_GATE_DISABLE (1 << 0)
#define RENCLK_GATE_D2 0x6208
#define VF_UNIT_CLOCK_GATE_DISABLE (1 << 9)
#define GS_UNIT_CLOCK_GATE_DISABLE (1 << 7)
#define CL_UNIT_CLOCK_GATE_DISABLE (1 << 6)
#define RAMCLK_GATE_D 0x6210 /* CRL only */
#define DEUC 0x6214 /* CRL only */
/*
* Palette regs
*/
#define PALETTE_A 0x0a000
#define PALETTE_B 0x0a800
/* MCH MMIO space */
/*
* MCHBAR mirror.
*
* This mirrors the MCHBAR MMIO space whose location is determined by
* device 0 function 0's pci config register 0x44 or 0x48 and matches it in
* every way. It is not accessible from the CP register read instructions.
*
*/
#define MCHBAR_MIRROR_BASE 0x10000
/** 915-945 and GM965 MCH register controlling DRAM channel access */
#define DCC 0x10200
#define DCC_ADDRESSING_MODE_SINGLE_CHANNEL (0 << 0)
#define DCC_ADDRESSING_MODE_DUAL_CHANNEL_ASYMMETRIC (1 << 0)
#define DCC_ADDRESSING_MODE_DUAL_CHANNEL_INTERLEAVED (2 << 0)
#define DCC_ADDRESSING_MODE_MASK (3 << 0)
#define DCC_CHANNEL_XOR_DISABLE (1 << 10)
#define DCC_CHANNEL_XOR_BIT_17 (1 << 9)
/** Pineview MCH register contains DDR3 setting */
#define CSHRDDR3CTL 0x101a8
#define CSHRDDR3CTL_DDR3 (1 << 2)
/** 965 MCH register controlling DRAM channel configuration */
#define C0DRB3 0x10206
#define C1DRB3 0x10606
/* Clocking configuration register */
#define CLKCFG 0x10c00
#define CLKCFG_FSB_400 (5 << 0) /* hrawclk 100 */
#define CLKCFG_FSB_533 (1 << 0) /* hrawclk 133 */
#define CLKCFG_FSB_667 (3 << 0) /* hrawclk 166 */
#define CLKCFG_FSB_800 (2 << 0) /* hrawclk 200 */
#define CLKCFG_FSB_1067 (6 << 0) /* hrawclk 266 */
#define CLKCFG_FSB_1333 (7 << 0) /* hrawclk 333 */
/* Note, below two are guess */
#define CLKCFG_FSB_1600 (4 << 0) /* hrawclk 400 */
#define CLKCFG_FSB_1600_ALT (0 << 0) /* hrawclk 400 */
#define CLKCFG_FSB_MASK (7 << 0)
#define CLKCFG_MEM_533 (1 << 4)
#define CLKCFG_MEM_667 (2 << 4)
#define CLKCFG_MEM_800 (3 << 4)
#define CLKCFG_MEM_MASK (7 << 4)
#define TSC1 0x11001
#define TSE (1<<0)
#define TR1 0x11006
#define TSFS 0x11020
#define TSFS_SLOPE_MASK 0x0000ff00
#define TSFS_SLOPE_SHIFT 8
#define TSFS_INTR_MASK 0x000000ff
#define CRSTANDVID 0x11100
#define PXVFREQ_BASE 0x11110 /* P[0-15]VIDFREQ (0x1114c) (Ironlake) */
#define PXVFREQ_PX_MASK 0x7f000000
#define PXVFREQ_PX_SHIFT 24
#define VIDFREQ_BASE 0x11110
#define VIDFREQ1 0x11110 /* VIDFREQ1-4 (0x1111c) (Cantiga) */
#define VIDFREQ2 0x11114
#define VIDFREQ3 0x11118
#define VIDFREQ4 0x1111c
#define VIDFREQ_P0_MASK 0x1f000000
#define VIDFREQ_P0_SHIFT 24
#define VIDFREQ_P0_CSCLK_MASK 0x00f00000
#define VIDFREQ_P0_CSCLK_SHIFT 20
#define VIDFREQ_P0_CRCLK_MASK 0x000f0000
#define VIDFREQ_P0_CRCLK_SHIFT 16
#define VIDFREQ_P1_MASK 0x00001f00
#define VIDFREQ_P1_SHIFT 8
#define VIDFREQ_P1_CSCLK_MASK 0x000000f0
#define VIDFREQ_P1_CSCLK_SHIFT 4
#define VIDFREQ_P1_CRCLK_MASK 0x0000000f
#define INTTOEXT_BASE_ILK 0x11300
#define INTTOEXT_BASE 0x11120 /* INTTOEXT1-8 (0x1113c) */
#define INTTOEXT_MAP3_SHIFT 24
#define INTTOEXT_MAP3_MASK (0x1f << INTTOEXT_MAP3_SHIFT)
#define INTTOEXT_MAP2_SHIFT 16
#define INTTOEXT_MAP2_MASK (0x1f << INTTOEXT_MAP2_SHIFT)
#define INTTOEXT_MAP1_SHIFT 8
#define INTTOEXT_MAP1_MASK (0x1f << INTTOEXT_MAP1_SHIFT)
#define INTTOEXT_MAP0_SHIFT 0
#define INTTOEXT_MAP0_MASK (0x1f << INTTOEXT_MAP0_SHIFT)
#define MEMSWCTL 0x11170 /* Ironlake only */
#define MEMCTL_CMD_MASK 0xe000
#define MEMCTL_CMD_SHIFT 13
#define MEMCTL_CMD_RCLK_OFF 0
#define MEMCTL_CMD_RCLK_ON 1
#define MEMCTL_CMD_CHFREQ 2
#define MEMCTL_CMD_CHVID 3
#define MEMCTL_CMD_VMMOFF 4
#define MEMCTL_CMD_VMMON 5
#define MEMCTL_CMD_STS (1<<12) /* write 1 triggers command, clears
when command complete */
#define MEMCTL_FREQ_MASK 0x0f00 /* jitter, from 0-15 */
#define MEMCTL_FREQ_SHIFT 8
#define MEMCTL_SFCAVM (1<<7)
#define MEMCTL_TGT_VID_MASK 0x007f
#define MEMIHYST 0x1117c
#define MEMINTREN 0x11180 /* 16 bits */
#define MEMINT_RSEXIT_EN (1<<8)
#define MEMINT_CX_SUPR_EN (1<<7)
#define MEMINT_CONT_BUSY_EN (1<<6)
#define MEMINT_AVG_BUSY_EN (1<<5)
#define MEMINT_EVAL_CHG_EN (1<<4)
#define MEMINT_MON_IDLE_EN (1<<3)
#define MEMINT_UP_EVAL_EN (1<<2)
#define MEMINT_DOWN_EVAL_EN (1<<1)
#define MEMINT_SW_CMD_EN (1<<0)
#define MEMINTRSTR 0x11182 /* 16 bits */
#define MEM_RSEXIT_MASK 0xc000
#define MEM_RSEXIT_SHIFT 14
#define MEM_CONT_BUSY_MASK 0x3000
#define MEM_CONT_BUSY_SHIFT 12
#define MEM_AVG_BUSY_MASK 0x0c00
#define MEM_AVG_BUSY_SHIFT 10
#define MEM_EVAL_CHG_MASK 0x0300
#define MEM_EVAL_BUSY_SHIFT 8
#define MEM_MON_IDLE_MASK 0x00c0
#define MEM_MON_IDLE_SHIFT 6
#define MEM_UP_EVAL_MASK 0x0030
#define MEM_UP_EVAL_SHIFT 4
#define MEM_DOWN_EVAL_MASK 0x000c
#define MEM_DOWN_EVAL_SHIFT 2
#define MEM_SW_CMD_MASK 0x0003
#define MEM_INT_STEER_GFX 0
#define MEM_INT_STEER_CMR 1
#define MEM_INT_STEER_SMI 2
#define MEM_INT_STEER_SCI 3
#define MEMINTRSTS 0x11184
#define MEMINT_RSEXIT (1<<7)
#define MEMINT_CONT_BUSY (1<<6)
#define MEMINT_AVG_BUSY (1<<5)
#define MEMINT_EVAL_CHG (1<<4)
#define MEMINT_MON_IDLE (1<<3)
#define MEMINT_UP_EVAL (1<<2)
#define MEMINT_DOWN_EVAL (1<<1)
#define MEMINT_SW_CMD (1<<0)
#define MEMMODECTL 0x11190
#define MEMMODE_BOOST_EN (1<<31)
#define MEMMODE_BOOST_FREQ_MASK 0x0f000000 /* jitter for boost, 0-15 */
#define MEMMODE_BOOST_FREQ_SHIFT 24
#define MEMMODE_IDLE_MODE_MASK 0x00030000
#define MEMMODE_IDLE_MODE_SHIFT 16
#define MEMMODE_IDLE_MODE_EVAL 0
#define MEMMODE_IDLE_MODE_CONT 1
#define MEMMODE_HWIDLE_EN (1<<15)
#define MEMMODE_SWMODE_EN (1<<14)
#define MEMMODE_RCLK_GATE (1<<13)
#define MEMMODE_HW_UPDATE (1<<12)
#define MEMMODE_FSTART_MASK 0x00000f00 /* starting jitter, 0-15 */
#define MEMMODE_FSTART_SHIFT 8
#define MEMMODE_FMAX_MASK 0x000000f0 /* max jitter, 0-15 */
#define MEMMODE_FMAX_SHIFT 4
#define MEMMODE_FMIN_MASK 0x0000000f /* min jitter, 0-15 */
#define RCBMAXAVG 0x1119c
#define MEMSWCTL2 0x1119e /* Cantiga only */
#define SWMEMCMD_RENDER_OFF (0 << 13)
#define SWMEMCMD_RENDER_ON (1 << 13)
#define SWMEMCMD_SWFREQ (2 << 13)
#define SWMEMCMD_TARVID (3 << 13)
#define SWMEMCMD_VRM_OFF (4 << 13)
#define SWMEMCMD_VRM_ON (5 << 13)
#define CMDSTS (1<<12)
#define SFCAVM (1<<11)
#define SWFREQ_MASK 0x0380 /* P0-7 */
#define SWFREQ_SHIFT 7
#define TARVID_MASK 0x001f
#define MEMSTAT_CTG 0x111a0
#define RCBMINAVG 0x111a0
#define RCUPEI 0x111b0
#define RCDNEI 0x111b4
#define MCHBAR_RENDER_STANDBY 0x111b8
#define RCX_SW_EXIT (1<<23)
#define RSX_STATUS_MASK 0x00700000
#define VIDCTL 0x111c0
#define VIDSTS 0x111c8
#define VIDSTART 0x111cc /* 8 bits */
#define MEMSTAT_ILK 0x111f8
#define MEMSTAT_VID_MASK 0x7f00
#define MEMSTAT_VID_SHIFT 8
#define MEMSTAT_PSTATE_MASK 0x00f8
#define MEMSTAT_PSTATE_SHIFT 3
#define MEMSTAT_MON_ACTV (1<<2)
#define MEMSTAT_SRC_CTL_MASK 0x0003
#define MEMSTAT_SRC_CTL_CORE 0
#define MEMSTAT_SRC_CTL_TRB 1
#define MEMSTAT_SRC_CTL_THM 2
#define MEMSTAT_SRC_CTL_STDBY 3
#define RCPREVBSYTUPAVG 0x113b8
#define RCPREVBSYTDNAVG 0x113bc
#define PMMISC 0x11214
#define MCPPCE_EN (1<<0) /* enable PM_MSG from PCH->MPC */
#define SDEW 0x1124c
#define CSIEW0 0x11250
#define CSIEW1 0x11254
#define CSIEW2 0x11258
#define PEW 0x1125c
#define DEW 0x11270
#define MCHAFE 0x112c0
#define CSIEC 0x112e0
#define DMIEC 0x112e4
#define DDREC 0x112e8
#define PEG0EC 0x112ec
#define PEG1EC 0x112f0
#define GFXEC 0x112f4
#define RPPREVBSYTUPAVG 0x113b8
#define RPPREVBSYTDNAVG 0x113bc
#define ECR 0x11600
#define ECR_GPFE (1<<31)
#define ECR_IMONE (1<<30)
#define ECR_CAP_MASK 0x0000001f /* Event range, 0-31 */
#define OGW0 0x11608
#define OGW1 0x1160c
#define EG0 0x11610
#define EG1 0x11614
#define EG2 0x11618
#define EG3 0x1161c
#define EG4 0x11620
#define EG5 0x11624
#define EG6 0x11628
#define EG7 0x1162c
#define PXW 0x11664
#define PXWL 0x11680
#define LCFUSE02 0x116c0
#define LCFUSE_HIV_MASK 0x000000ff
#define CSIPLL0 0x12c10
#define DDRMPLL1 0X12c20
#define PEG_BAND_GAP_DATA 0x14d68
/*
* Logical Context regs
*/
#define CCID 0x2180
#define CCID_EN (1<<0)
/*
* Overlay regs
*/
#define OVADD 0x30000
#define DOVSTA 0x30008
#define OC_BUF (0x3<<20)
#define OGAMC5 0x30010
#define OGAMC4 0x30014
#define OGAMC3 0x30018
#define OGAMC2 0x3001c
#define OGAMC1 0x30020
#define OGAMC0 0x30024
/*
* Display engine regs
*/
/* Pipe A timing regs */
#define HTOTAL_A 0x60000
#define HBLANK_A 0x60004
#define HSYNC_A 0x60008
#define VTOTAL_A 0x6000c
#define VBLANK_A 0x60010
#define VSYNC_A 0x60014
#define PIPEASRC 0x6001c
#define BCLRPAT_A 0x60020
/* Pipe B timing regs */
#define HTOTAL_B 0x61000
#define HBLANK_B 0x61004
#define HSYNC_B 0x61008
#define VTOTAL_B 0x6100c
#define VBLANK_B 0x61010
#define VSYNC_B 0x61014
#define PIPEBSRC 0x6101c
#define BCLRPAT_B 0x61020
#define HTOTAL(pipe) _PIPE(pipe, HTOTAL_A, HTOTAL_B)
#define HBLANK(pipe) _PIPE(pipe, HBLANK_A, HBLANK_B)
#define HSYNC(pipe) _PIPE(pipe, HSYNC_A, HSYNC_B)
#define VTOTAL(pipe) _PIPE(pipe, VTOTAL_A, VTOTAL_B)
#define VBLANK(pipe) _PIPE(pipe, VBLANK_A, VBLANK_B)
#define VSYNC(pipe) _PIPE(pipe, VSYNC_A, VSYNC_B)
#define PIPESRC(pipe) _PIPE(pipe, PIPEASRC, PIPEBSRC)
#define BCLRPAT(pipe) _PIPE(pipe, BCLRPAT_A, BCLRPAT_B)
/* VGA port control */
#define ADPA 0x61100
#define ADPA_DAC_ENABLE (1<<31)
#define ADPA_DAC_DISABLE 0
#define ADPA_PIPE_SELECT_MASK (1<<30)
#define ADPA_PIPE_A_SELECT 0
#define ADPA_PIPE_B_SELECT (1<<30)
#define ADPA_USE_VGA_HVPOLARITY (1<<15)
#define ADPA_SETS_HVPOLARITY 0
#define ADPA_VSYNC_CNTL_DISABLE (1<<11)
#define ADPA_VSYNC_CNTL_ENABLE 0
#define ADPA_HSYNC_CNTL_DISABLE (1<<10)
#define ADPA_HSYNC_CNTL_ENABLE 0
#define ADPA_VSYNC_ACTIVE_HIGH (1<<4)
#define ADPA_VSYNC_ACTIVE_LOW 0
#define ADPA_HSYNC_ACTIVE_HIGH (1<<3)
#define ADPA_HSYNC_ACTIVE_LOW 0
#define ADPA_DPMS_MASK (~(3<<10))
#define ADPA_DPMS_ON (0<<10)
#define ADPA_DPMS_SUSPEND (1<<10)
#define ADPA_DPMS_STANDBY (2<<10)
#define ADPA_DPMS_OFF (3<<10)
/* Hotplug control (945+ only) */
#define PORT_HOTPLUG_EN 0x61110
#define HDMIB_HOTPLUG_INT_EN (1 << 29)
#define DPB_HOTPLUG_INT_EN (1 << 29)
#define HDMIC_HOTPLUG_INT_EN (1 << 28)
#define DPC_HOTPLUG_INT_EN (1 << 28)
#define HDMID_HOTPLUG_INT_EN (1 << 27)
#define DPD_HOTPLUG_INT_EN (1 << 27)
#define SDVOB_HOTPLUG_INT_EN (1 << 26)
#define SDVOC_HOTPLUG_INT_EN (1 << 25)
#define TV_HOTPLUG_INT_EN (1 << 18)
#define CRT_HOTPLUG_INT_EN (1 << 9)
#define CRT_HOTPLUG_FORCE_DETECT (1 << 3)
#define CRT_HOTPLUG_ACTIVATION_PERIOD_32 (0 << 8)
/* must use period 64 on GM45 according to docs */
#define CRT_HOTPLUG_ACTIVATION_PERIOD_64 (1 << 8)
#define CRT_HOTPLUG_DAC_ON_TIME_2M (0 << 7)
#define CRT_HOTPLUG_DAC_ON_TIME_4M (1 << 7)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_40 (0 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_50 (1 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_60 (2 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_70 (3 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_MASK (3 << 5)
#define CRT_HOTPLUG_DETECT_DELAY_1G (0 << 4)
#define CRT_HOTPLUG_DETECT_DELAY_2G (1 << 4)
#define CRT_HOTPLUG_DETECT_VOLTAGE_325MV (0 << 2)
#define CRT_HOTPLUG_DETECT_VOLTAGE_475MV (1 << 2)
#define PORT_HOTPLUG_STAT 0x61114
#define HDMIB_HOTPLUG_INT_STATUS (1 << 29)
#define DPB_HOTPLUG_INT_STATUS (1 << 29)
#define HDMIC_HOTPLUG_INT_STATUS (1 << 28)
#define DPC_HOTPLUG_INT_STATUS (1 << 28)
#define HDMID_HOTPLUG_INT_STATUS (1 << 27)
#define DPD_HOTPLUG_INT_STATUS (1 << 27)
#define CRT_HOTPLUG_INT_STATUS (1 << 11)
#define TV_HOTPLUG_INT_STATUS (1 << 10)
#define CRT_HOTPLUG_MONITOR_MASK (3 << 8)
#define CRT_HOTPLUG_MONITOR_COLOR (3 << 8)
#define CRT_HOTPLUG_MONITOR_MONO (2 << 8)
#define CRT_HOTPLUG_MONITOR_NONE (0 << 8)
#define SDVOC_HOTPLUG_INT_STATUS (1 << 7)
#define SDVOB_HOTPLUG_INT_STATUS (1 << 6)
/* SDVO port control */
#define SDVOB 0x61140
#define SDVOC 0x61160
#define SDVO_ENABLE (1 << 31)
#define SDVO_PIPE_B_SELECT (1 << 30)
#define SDVO_STALL_SELECT (1 << 29)
#define SDVO_INTERRUPT_ENABLE (1 << 26)
/**
* 915G/GM SDVO pixel multiplier.
*
* Programmed value is multiplier - 1, up to 5x.
*
* \sa DPLL_MD_UDI_MULTIPLIER_MASK
*/
#define SDVO_PORT_MULTIPLY_MASK (7 << 23)
#define SDVO_PORT_MULTIPLY_SHIFT 23
#define SDVO_PHASE_SELECT_MASK (15 << 19)
#define SDVO_PHASE_SELECT_DEFAULT (6 << 19)
#define SDVO_CLOCK_OUTPUT_INVERT (1 << 18)
#define SDVOC_GANG_MODE (1 << 16)
#define SDVO_ENCODING_SDVO (0x0 << 10)
#define SDVO_ENCODING_HDMI (0x2 << 10)
/** Requird for HDMI operation */
#define SDVO_NULL_PACKETS_DURING_VSYNC (1 << 9)
#define SDVO_BORDER_ENABLE (1 << 7)
#define SDVO_AUDIO_ENABLE (1 << 6)
/** New with 965, default is to be set */
#define SDVO_VSYNC_ACTIVE_HIGH (1 << 4)
/** New with 965, default is to be set */
#define SDVO_HSYNC_ACTIVE_HIGH (1 << 3)
#define SDVOB_PCIE_CONCURRENCY (1 << 3)
#define SDVO_DETECTED (1 << 2)
/* Bits to be preserved when writing */
#define SDVOB_PRESERVE_MASK ((1 << 17) | (1 << 16) | (1 << 14) | (1 << 26))
#define SDVOC_PRESERVE_MASK ((1 << 17) | (1 << 26))
/* DVO port control */
#define DVOA 0x61120
#define DVOB 0x61140
#define DVOC 0x61160
#define DVO_ENABLE (1 << 31)
#define DVO_PIPE_B_SELECT (1 << 30)
#define DVO_PIPE_STALL_UNUSED (0 << 28)
#define DVO_PIPE_STALL (1 << 28)
#define DVO_PIPE_STALL_TV (2 << 28)
#define DVO_PIPE_STALL_MASK (3 << 28)
#define DVO_USE_VGA_SYNC (1 << 15)
#define DVO_DATA_ORDER_I740 (0 << 14)
#define DVO_DATA_ORDER_FP (1 << 14)
#define DVO_VSYNC_DISABLE (1 << 11)
#define DVO_HSYNC_DISABLE (1 << 10)
#define DVO_VSYNC_TRISTATE (1 << 9)
#define DVO_HSYNC_TRISTATE (1 << 8)
#define DVO_BORDER_ENABLE (1 << 7)
#define DVO_DATA_ORDER_GBRG (1 << 6)
#define DVO_DATA_ORDER_RGGB (0 << 6)
#define DVO_DATA_ORDER_GBRG_ERRATA (0 << 6)
#define DVO_DATA_ORDER_RGGB_ERRATA (1 << 6)
#define DVO_VSYNC_ACTIVE_HIGH (1 << 4)
#define DVO_HSYNC_ACTIVE_HIGH (1 << 3)
#define DVO_BLANK_ACTIVE_HIGH (1 << 2)
#define DVO_OUTPUT_CSTATE_PIXELS (1 << 1) /* SDG only */
#define DVO_OUTPUT_SOURCE_SIZE_PIXELS (1 << 0) /* SDG only */
#define DVO_PRESERVE_MASK (0x7<<24)
#define DVOA_SRCDIM 0x61124
#define DVOB_SRCDIM 0x61144
#define DVOC_SRCDIM 0x61164
#define DVO_SRCDIM_HORIZONTAL_SHIFT 12
#define DVO_SRCDIM_VERTICAL_SHIFT 0
/* LVDS port control */
#define LVDS 0x61180
/*
* Enables the LVDS port. This bit must be set before DPLLs are enabled, as
* the DPLL semantics change when the LVDS is assigned to that pipe.
*/
#define LVDS_PORT_EN (1 << 31)
/* Selects pipe B for LVDS data. Must be set on pre-965. */
#define LVDS_PIPEB_SELECT (1 << 30)
/* LVDS dithering flag on 965/g4x platform */
#define LVDS_ENABLE_DITHER (1 << 25)
/* Enable border for unscaled (or aspect-scaled) display */
#define LVDS_BORDER_ENABLE (1 << 15)
/*
* Enables the A0-A2 data pairs and CLKA, containing 18 bits of color data per
* pixel.
*/
#define LVDS_A0A2_CLKA_POWER_MASK (3 << 8)
#define LVDS_A0A2_CLKA_POWER_DOWN (0 << 8)
#define LVDS_A0A2_CLKA_POWER_UP (3 << 8)
/*
* Controls the A3 data pair, which contains the additional LSBs for 24 bit
* mode. Only enabled if LVDS_A0A2_CLKA_POWER_UP also indicates it should be
* on.
*/
#define LVDS_A3_POWER_MASK (3 << 6)
#define LVDS_A3_POWER_DOWN (0 << 6)
#define LVDS_A3_POWER_UP (3 << 6)
/*
* Controls the CLKB pair. This should only be set when LVDS_B0B3_POWER_UP
* is set.
*/
#define LVDS_CLKB_POWER_MASK (3 << 4)
#define LVDS_CLKB_POWER_DOWN (0 << 4)
#define LVDS_CLKB_POWER_UP (3 << 4)
/*
* Controls the B0-B3 data pairs. This must be set to match the DPLL p2
* setting for whether we are in dual-channel mode. The B3 pair will
* additionally only be powered up when LVDS_A3_POWER_UP is set.
*/
#define LVDS_B0B3_POWER_MASK (3 << 2)
#define LVDS_B0B3_POWER_DOWN (0 << 2)
#define LVDS_B0B3_POWER_UP (3 << 2)
/* Panel power sequencing */
#define PP_STATUS 0x61200
#define PP_ON (1 << 31)
/*
* Indicates that all dependencies of the panel are on:
*
* - PLL enabled
* - pipe enabled
* - LVDS/DVOB/DVOC on
*/
#define PP_READY (1 << 30)
#define PP_SEQUENCE_NONE (0 << 28)
#define PP_SEQUENCE_ON (1 << 28)
#define PP_SEQUENCE_OFF (2 << 28)
#define PP_SEQUENCE_MASK 0x30000000
#define PP_CYCLE_DELAY_ACTIVE (1 << 27)
#define PP_SEQUENCE_STATE_ON_IDLE (1 << 3)
#define PP_SEQUENCE_STATE_MASK 0x0000000f
#define PP_CONTROL 0x61204
#define POWER_TARGET_ON (1 << 0)
#define PP_ON_DELAYS 0x61208
#define PP_OFF_DELAYS 0x6120c
#define PP_DIVISOR 0x61210
/* Panel fitting */
#define PFIT_CONTROL 0x61230
#define PFIT_ENABLE (1 << 31)
#define PFIT_PIPE_MASK (3 << 29)
#define PFIT_PIPE_SHIFT 29
#define VERT_INTERP_DISABLE (0 << 10)
#define VERT_INTERP_BILINEAR (1 << 10)
#define VERT_INTERP_MASK (3 << 10)
#define VERT_AUTO_SCALE (1 << 9)
#define HORIZ_INTERP_DISABLE (0 << 6)
#define HORIZ_INTERP_BILINEAR (1 << 6)
#define HORIZ_INTERP_MASK (3 << 6)
#define HORIZ_AUTO_SCALE (1 << 5)
#define PANEL_8TO6_DITHER_ENABLE (1 << 3)
#define PFIT_FILTER_FUZZY (0 << 24)
#define PFIT_SCALING_AUTO (0 << 26)
#define PFIT_SCALING_PROGRAMMED (1 << 26)
#define PFIT_SCALING_PILLAR (2 << 26)
#define PFIT_SCALING_LETTER (3 << 26)
#define PFIT_PGM_RATIOS 0x61234
#define PFIT_VERT_SCALE_MASK 0xfff00000
#define PFIT_HORIZ_SCALE_MASK 0x0000fff0
/* Pre-965 */
#define PFIT_VERT_SCALE_SHIFT 20
#define PFIT_VERT_SCALE_MASK 0xfff00000
#define PFIT_HORIZ_SCALE_SHIFT 4
#define PFIT_HORIZ_SCALE_MASK 0x0000fff0
/* 965+ */
#define PFIT_VERT_SCALE_SHIFT_965 16
#define PFIT_VERT_SCALE_MASK_965 0x1fff0000
#define PFIT_HORIZ_SCALE_SHIFT_965 0
#define PFIT_HORIZ_SCALE_MASK_965 0x00001fff
#define PFIT_AUTO_RATIOS 0x61238
/* Backlight control */
#define BLC_PWM_CTL 0x61254
#define BACKLIGHT_MODULATION_FREQ_SHIFT (17)
#define BLC_PWM_CTL2 0x61250 /* 965+ only */
#define BLM_COMBINATION_MODE (1 << 30)
/*
* This is the most significant 15 bits of the number of backlight cycles in a
* complete cycle of the modulated backlight control.
*
* The actual value is this field multiplied by two.
*/
#define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17)
#define BLM_LEGACY_MODE (1 << 16)
/*
* This is the number of cycles out of the backlight modulation cycle for which
* the backlight is on.
*
* This field must be no greater than the number of cycles in the complete
* backlight modulation cycle.
*/
#define BACKLIGHT_DUTY_CYCLE_SHIFT (0)
#define BACKLIGHT_DUTY_CYCLE_MASK (0xffff)
#define BLC_HIST_CTL 0x61260
/* TV port control */
#define TV_CTL 0x68000
/** Enables the TV encoder */
# define TV_ENC_ENABLE (1 << 31)
/** Sources the TV encoder input from pipe B instead of A. */
# define TV_ENC_PIPEB_SELECT (1 << 30)
/** Outputs composite video (DAC A only) */
# define TV_ENC_OUTPUT_COMPOSITE (0 << 28)
/** Outputs SVideo video (DAC B/C) */
# define TV_ENC_OUTPUT_SVIDEO (1 << 28)
/** Outputs Component video (DAC A/B/C) */
# define TV_ENC_OUTPUT_COMPONENT (2 << 28)
/** Outputs Composite and SVideo (DAC A/B/C) */
# define TV_ENC_OUTPUT_SVIDEO_COMPOSITE (3 << 28)
# define TV_TRILEVEL_SYNC (1 << 21)
/** Enables slow sync generation (945GM only) */
# define TV_SLOW_SYNC (1 << 20)
/** Selects 4x oversampling for 480i and 576p */
# define TV_OVERSAMPLE_4X (0 << 18)
/** Selects 2x oversampling for 720p and 1080i */
# define TV_OVERSAMPLE_2X (1 << 18)
/** Selects no oversampling for 1080p */
# define TV_OVERSAMPLE_NONE (2 << 18)
/** Selects 8x oversampling */
# define TV_OVERSAMPLE_8X (3 << 18)
/** Selects progressive mode rather than interlaced */
# define TV_PROGRESSIVE (1 << 17)
/** Sets the colorburst to PAL mode. Required for non-M PAL modes. */
# define TV_PAL_BURST (1 << 16)
/** Field for setting delay of Y compared to C */
# define TV_YC_SKEW_MASK (7 << 12)
/** Enables a fix for 480p/576p standard definition modes on the 915GM only */
# define TV_ENC_SDP_FIX (1 << 11)
/**
* Enables a fix for the 915GM only.
*
* Not sure what it does.
*/
# define TV_ENC_C0_FIX (1 << 10)
/** Bits that must be preserved by software */
# define TV_CTL_SAVE ((1 << 11) | (3 << 9) | (7 << 6) | 0xf)
# define TV_FUSE_STATE_MASK (3 << 4)
/** Read-only state that reports all features enabled */
# define TV_FUSE_STATE_ENABLED (0 << 4)
/** Read-only state that reports that Macrovision is disabled in hardware*/
# define TV_FUSE_STATE_NO_MACROVISION (1 << 4)
/** Read-only state that reports that TV-out is disabled in hardware. */
# define TV_FUSE_STATE_DISABLED (2 << 4)
/** Normal operation */
# define TV_TEST_MODE_NORMAL (0 << 0)
/** Encoder test pattern 1 - combo pattern */
# define TV_TEST_MODE_PATTERN_1 (1 << 0)
/** Encoder test pattern 2 - full screen vertical 75% color bars */
# define TV_TEST_MODE_PATTERN_2 (2 << 0)
/** Encoder test pattern 3 - full screen horizontal 75% color bars */
# define TV_TEST_MODE_PATTERN_3 (3 << 0)
/** Encoder test pattern 4 - random noise */
# define TV_TEST_MODE_PATTERN_4 (4 << 0)
/** Encoder test pattern 5 - linear color ramps */
# define TV_TEST_MODE_PATTERN_5 (5 << 0)
/**
* This test mode forces the DACs to 50% of full output.
*
* This is used for load detection in combination with TVDAC_SENSE_MASK
*/
# define TV_TEST_MODE_MONITOR_DETECT (7 << 0)
# define TV_TEST_MODE_MASK (7 << 0)
#define TV_DAC 0x68004
# define TV_DAC_SAVE 0x00ffff00
/**
* Reports that DAC state change logic has reported change (RO).
*
* This gets cleared when TV_DAC_STATE_EN is cleared
*/
# define TVDAC_STATE_CHG (1 << 31)
# define TVDAC_SENSE_MASK (7 << 28)
/** Reports that DAC A voltage is above the detect threshold */
# define TVDAC_A_SENSE (1 << 30)
/** Reports that DAC B voltage is above the detect threshold */
# define TVDAC_B_SENSE (1 << 29)
/** Reports that DAC C voltage is above the detect threshold */
# define TVDAC_C_SENSE (1 << 28)
/**
* Enables DAC state detection logic, for load-based TV detection.
*
* The PLL of the chosen pipe (in TV_CTL) must be running, and the encoder set
* to off, for load detection to work.
*/
# define TVDAC_STATE_CHG_EN (1 << 27)
/** Sets the DAC A sense value to high */
# define TVDAC_A_SENSE_CTL (1 << 26)
/** Sets the DAC B sense value to high */
# define TVDAC_B_SENSE_CTL (1 << 25)
/** Sets the DAC C sense value to high */
# define TVDAC_C_SENSE_CTL (1 << 24)
/** Overrides the ENC_ENABLE and DAC voltage levels */
# define DAC_CTL_OVERRIDE (1 << 7)
/** Sets the slew rate. Must be preserved in software */
# define ENC_TVDAC_SLEW_FAST (1 << 6)
# define DAC_A_1_3_V (0 << 4)
# define DAC_A_1_1_V (1 << 4)
# define DAC_A_0_7_V (2 << 4)
# define DAC_A_MASK (3 << 4)
# define DAC_B_1_3_V (0 << 2)
# define DAC_B_1_1_V (1 << 2)
# define DAC_B_0_7_V (2 << 2)
# define DAC_B_MASK (3 << 2)
# define DAC_C_1_3_V (0 << 0)
# define DAC_C_1_1_V (1 << 0)
# define DAC_C_0_7_V (2 << 0)
# define DAC_C_MASK (3 << 0)
/**
* CSC coefficients are stored in a floating point format with 9 bits of
* mantissa and 2 or 3 bits of exponent. The exponent is represented as 2**-n,
* where 2-bit exponents are unsigned n, and 3-bit exponents are signed n with
* -1 (0x3) being the only legal negative value.
*/
#define TV_CSC_Y 0x68010
# define TV_RY_MASK 0x07ff0000
# define TV_RY_SHIFT 16
# define TV_GY_MASK 0x00000fff
# define TV_GY_SHIFT 0
#define TV_CSC_Y2 0x68014
# define TV_BY_MASK 0x07ff0000
# define TV_BY_SHIFT 16
/**
* Y attenuation for component video.
*
* Stored in 1.9 fixed point.
*/
# define TV_AY_MASK 0x000003ff
# define TV_AY_SHIFT 0
#define TV_CSC_U 0x68018
# define TV_RU_MASK 0x07ff0000
# define TV_RU_SHIFT 16
# define TV_GU_MASK 0x000007ff
# define TV_GU_SHIFT 0
#define TV_CSC_U2 0x6801c
# define TV_BU_MASK 0x07ff0000
# define TV_BU_SHIFT 16
/**
* U attenuation for component video.
*
* Stored in 1.9 fixed point.
*/
# define TV_AU_MASK 0x000003ff
# define TV_AU_SHIFT 0
#define TV_CSC_V 0x68020
# define TV_RV_MASK 0x0fff0000
# define TV_RV_SHIFT 16
# define TV_GV_MASK 0x000007ff
# define TV_GV_SHIFT 0
#define TV_CSC_V2 0x68024
# define TV_BV_MASK 0x07ff0000
# define TV_BV_SHIFT 16
/**
* V attenuation for component video.
*
* Stored in 1.9 fixed point.
*/
# define TV_AV_MASK 0x000007ff
# define TV_AV_SHIFT 0
#define TV_CLR_KNOBS 0x68028
/** 2s-complement brightness adjustment */
# define TV_BRIGHTNESS_MASK 0xff000000
# define TV_BRIGHTNESS_SHIFT 24
/** Contrast adjustment, as a 2.6 unsigned floating point number */
# define TV_CONTRAST_MASK 0x00ff0000
# define TV_CONTRAST_SHIFT 16
/** Saturation adjustment, as a 2.6 unsigned floating point number */
# define TV_SATURATION_MASK 0x0000ff00
# define TV_SATURATION_SHIFT 8
/** Hue adjustment, as an integer phase angle in degrees */
# define TV_HUE_MASK 0x000000ff
# define TV_HUE_SHIFT 0
#define TV_CLR_LEVEL 0x6802c
/** Controls the DAC level for black */
# define TV_BLACK_LEVEL_MASK 0x01ff0000
# define TV_BLACK_LEVEL_SHIFT 16
/** Controls the DAC level for blanking */
# define TV_BLANK_LEVEL_MASK 0x000001ff
# define TV_BLANK_LEVEL_SHIFT 0
#define TV_H_CTL_1 0x68030
/** Number of pixels in the hsync. */
# define TV_HSYNC_END_MASK 0x1fff0000
# define TV_HSYNC_END_SHIFT 16
/** Total number of pixels minus one in the line (display and blanking). */
# define TV_HTOTAL_MASK 0x00001fff
# define TV_HTOTAL_SHIFT 0
#define TV_H_CTL_2 0x68034
/** Enables the colorburst (needed for non-component color) */
# define TV_BURST_ENA (1 << 31)
/** Offset of the colorburst from the start of hsync, in pixels minus one. */
# define TV_HBURST_START_SHIFT 16
# define TV_HBURST_START_MASK 0x1fff0000
/** Length of the colorburst */
# define TV_HBURST_LEN_SHIFT 0
# define TV_HBURST_LEN_MASK 0x0001fff
#define TV_H_CTL_3 0x68038
/** End of hblank, measured in pixels minus one from start of hsync */
# define TV_HBLANK_END_SHIFT 16
# define TV_HBLANK_END_MASK 0x1fff0000
/** Start of hblank, measured in pixels minus one from start of hsync */
# define TV_HBLANK_START_SHIFT 0
# define TV_HBLANK_START_MASK 0x0001fff
#define TV_V_CTL_1 0x6803c
/** XXX */
# define TV_NBR_END_SHIFT 16
# define TV_NBR_END_MASK 0x07ff0000
/** XXX */
# define TV_VI_END_F1_SHIFT 8
# define TV_VI_END_F1_MASK 0x00003f00
/** XXX */
# define TV_VI_END_F2_SHIFT 0
# define TV_VI_END_F2_MASK 0x0000003f
#define TV_V_CTL_2 0x68040
/** Length of vsync, in half lines */
# define TV_VSYNC_LEN_MASK 0x07ff0000
# define TV_VSYNC_LEN_SHIFT 16
/** Offset of the start of vsync in field 1, measured in one less than the
* number of half lines.
*/
# define TV_VSYNC_START_F1_MASK 0x00007f00
# define TV_VSYNC_START_F1_SHIFT 8
/**
* Offset of the start of vsync in field 2, measured in one less than the
* number of half lines.
*/
# define TV_VSYNC_START_F2_MASK 0x0000007f
# define TV_VSYNC_START_F2_SHIFT 0
#define TV_V_CTL_3 0x68044
/** Enables generation of the equalization signal */
# define TV_EQUAL_ENA (1 << 31)
/** Length of vsync, in half lines */
# define TV_VEQ_LEN_MASK 0x007f0000
# define TV_VEQ_LEN_SHIFT 16
/** Offset of the start of equalization in field 1, measured in one less than
* the number of half lines.
*/
# define TV_VEQ_START_F1_MASK 0x0007f00
# define TV_VEQ_START_F1_SHIFT 8
/**
* Offset of the start of equalization in field 2, measured in one less than
* the number of half lines.
*/
# define TV_VEQ_START_F2_MASK 0x000007f
# define TV_VEQ_START_F2_SHIFT 0
#define TV_V_CTL_4 0x68048
/**
* Offset to start of vertical colorburst, measured in one less than the
* number of lines from vertical start.
*/
# define TV_VBURST_START_F1_MASK 0x003f0000
# define TV_VBURST_START_F1_SHIFT 16
/**
* Offset to the end of vertical colorburst, measured in one less than the
* number of lines from the start of NBR.
*/
# define TV_VBURST_END_F1_MASK 0x000000ff
# define TV_VBURST_END_F1_SHIFT 0
#define TV_V_CTL_5 0x6804c
/**
* Offset to start of vertical colorburst, measured in one less than the
* number of lines from vertical start.
*/
# define TV_VBURST_START_F2_MASK 0x003f0000
# define TV_VBURST_START_F2_SHIFT 16
/**
* Offset to the end of vertical colorburst, measured in one less than the
* number of lines from the start of NBR.
*/
# define TV_VBURST_END_F2_MASK 0x000000ff
# define TV_VBURST_END_F2_SHIFT 0
#define TV_V_CTL_6 0x68050
/**
* Offset to start of vertical colorburst, measured in one less than the
* number of lines from vertical start.
*/
# define TV_VBURST_START_F3_MASK 0x003f0000
# define TV_VBURST_START_F3_SHIFT 16
/**
* Offset to the end of vertical colorburst, measured in one less than the
* number of lines from the start of NBR.
*/
# define TV_VBURST_END_F3_MASK 0x000000ff
# define TV_VBURST_END_F3_SHIFT 0
#define TV_V_CTL_7 0x68054
/**
* Offset to start of vertical colorburst, measured in one less than the
* number of lines from vertical start.
*/
# define TV_VBURST_START_F4_MASK 0x003f0000
# define TV_VBURST_START_F4_SHIFT 16
/**
* Offset to the end of vertical colorburst, measured in one less than the
* number of lines from the start of NBR.
*/
# define TV_VBURST_END_F4_MASK 0x000000ff
# define TV_VBURST_END_F4_SHIFT 0
#define TV_SC_CTL_1 0x68060
/** Turns on the first subcarrier phase generation DDA */
# define TV_SC_DDA1_EN (1 << 31)
/** Turns on the first subcarrier phase generation DDA */
# define TV_SC_DDA2_EN (1 << 30)
/** Turns on the first subcarrier phase generation DDA */
# define TV_SC_DDA3_EN (1 << 29)
/** Sets the subcarrier DDA to reset frequency every other field */
# define TV_SC_RESET_EVERY_2 (0 << 24)
/** Sets the subcarrier DDA to reset frequency every fourth field */
# define TV_SC_RESET_EVERY_4 (1 << 24)
/** Sets the subcarrier DDA to reset frequency every eighth field */
# define TV_SC_RESET_EVERY_8 (2 << 24)
/** Sets the subcarrier DDA to never reset the frequency */
# define TV_SC_RESET_NEVER (3 << 24)
/** Sets the peak amplitude of the colorburst.*/
# define TV_BURST_LEVEL_MASK 0x00ff0000
# define TV_BURST_LEVEL_SHIFT 16
/** Sets the increment of the first subcarrier phase generation DDA */
# define TV_SCDDA1_INC_MASK 0x00000fff
# define TV_SCDDA1_INC_SHIFT 0
#define TV_SC_CTL_2 0x68064
/** Sets the rollover for the second subcarrier phase generation DDA */
# define TV_SCDDA2_SIZE_MASK 0x7fff0000
# define TV_SCDDA2_SIZE_SHIFT 16
/** Sets the increent of the second subcarrier phase generation DDA */
# define TV_SCDDA2_INC_MASK 0x00007fff
# define TV_SCDDA2_INC_SHIFT 0
#define TV_SC_CTL_3 0x68068
/** Sets the rollover for the third subcarrier phase generation DDA */
# define TV_SCDDA3_SIZE_MASK 0x7fff0000
# define TV_SCDDA3_SIZE_SHIFT 16
/** Sets the increent of the third subcarrier phase generation DDA */
# define TV_SCDDA3_INC_MASK 0x00007fff
# define TV_SCDDA3_INC_SHIFT 0
#define TV_WIN_POS 0x68070
/** X coordinate of the display from the start of horizontal active */
# define TV_XPOS_MASK 0x1fff0000
# define TV_XPOS_SHIFT 16
/** Y coordinate of the display from the start of vertical active (NBR) */
# define TV_YPOS_MASK 0x00000fff
# define TV_YPOS_SHIFT 0
#define TV_WIN_SIZE 0x68074
/** Horizontal size of the display window, measured in pixels*/
# define TV_XSIZE_MASK 0x1fff0000
# define TV_XSIZE_SHIFT 16
/**
* Vertical size of the display window, measured in pixels.
*
* Must be even for interlaced modes.
*/
# define TV_YSIZE_MASK 0x00000fff
# define TV_YSIZE_SHIFT 0
#define TV_FILTER_CTL_1 0x68080
/**
* Enables automatic scaling calculation.
*
* If set, the rest of the registers are ignored, and the calculated values can
* be read back from the register.
*/
# define TV_AUTO_SCALE (1 << 31)
/**
* Disables the vertical filter.
*
* This is required on modes more than 1024 pixels wide */
# define TV_V_FILTER_BYPASS (1 << 29)
/** Enables adaptive vertical filtering */
# define TV_VADAPT (1 << 28)
# define TV_VADAPT_MODE_MASK (3 << 26)
/** Selects the least adaptive vertical filtering mode */
# define TV_VADAPT_MODE_LEAST (0 << 26)
/** Selects the moderately adaptive vertical filtering mode */
# define TV_VADAPT_MODE_MODERATE (1 << 26)
/** Selects the most adaptive vertical filtering mode */
# define TV_VADAPT_MODE_MOST (3 << 26)
/**
* Sets the horizontal scaling factor.
*
* This should be the fractional part of the horizontal scaling factor divided
* by the oversampling rate. TV_HSCALE should be less than 1, and set to:
*
* (src width - 1) / ((oversample * dest width) - 1)
*/
# define TV_HSCALE_FRAC_MASK 0x00003fff
# define TV_HSCALE_FRAC_SHIFT 0
#define TV_FILTER_CTL_2 0x68084
/**
* Sets the integer part of the 3.15 fixed-point vertical scaling factor.
*
* TV_VSCALE should be (src height - 1) / ((interlace * dest height) - 1)
*/
# define TV_VSCALE_INT_MASK 0x00038000
# define TV_VSCALE_INT_SHIFT 15
/**
* Sets the fractional part of the 3.15 fixed-point vertical scaling factor.
*
* \sa TV_VSCALE_INT_MASK
*/
# define TV_VSCALE_FRAC_MASK 0x00007fff
# define TV_VSCALE_FRAC_SHIFT 0
#define TV_FILTER_CTL_3 0x68088
/**
* Sets the integer part of the 3.15 fixed-point vertical scaling factor.
*
* TV_VSCALE should be (src height - 1) / (1/4 * (dest height - 1))
*
* For progressive modes, TV_VSCALE_IP_INT should be set to zeroes.
*/
# define TV_VSCALE_IP_INT_MASK 0x00038000
# define TV_VSCALE_IP_INT_SHIFT 15
/**
* Sets the fractional part of the 3.15 fixed-point vertical scaling factor.
*
* For progressive modes, TV_VSCALE_IP_INT should be set to zeroes.
*
* \sa TV_VSCALE_IP_INT_MASK
*/
# define TV_VSCALE_IP_FRAC_MASK 0x00007fff
# define TV_VSCALE_IP_FRAC_SHIFT 0
#define TV_CC_CONTROL 0x68090
# define TV_CC_ENABLE (1 << 31)
/**
* Specifies which field to send the CC data in.
*
* CC data is usually sent in field 0.
*/
# define TV_CC_FID_MASK (1 << 27)
# define TV_CC_FID_SHIFT 27
/** Sets the horizontal position of the CC data. Usually 135. */
# define TV_CC_HOFF_MASK 0x03ff0000
# define TV_CC_HOFF_SHIFT 16
/** Sets the vertical position of the CC data. Usually 21 */
# define TV_CC_LINE_MASK 0x0000003f
# define TV_CC_LINE_SHIFT 0
#define TV_CC_DATA 0x68094
# define TV_CC_RDY (1 << 31)
/** Second word of CC data to be transmitted. */
# define TV_CC_DATA_2_MASK 0x007f0000
# define TV_CC_DATA_2_SHIFT 16
/** First word of CC data to be transmitted. */
# define TV_CC_DATA_1_MASK 0x0000007f
# define TV_CC_DATA_1_SHIFT 0
#define TV_H_LUMA_0 0x68100
#define TV_H_LUMA_59 0x681ec
#define TV_H_CHROMA_0 0x68200
#define TV_H_CHROMA_59 0x682ec
#define TV_V_LUMA_0 0x68300
#define TV_V_LUMA_42 0x683a8
#define TV_V_CHROMA_0 0x68400
#define TV_V_CHROMA_42 0x684a8
/* Display Port */
#define DP_A 0x64000 /* eDP */
#define DP_B 0x64100
#define DP_C 0x64200
#define DP_D 0x64300
#define DP_PORT_EN (1 << 31)
#define DP_PIPEB_SELECT (1 << 30)
/* Link training mode - select a suitable mode for each stage */
#define DP_LINK_TRAIN_PAT_1 (0 << 28)
#define DP_LINK_TRAIN_PAT_2 (1 << 28)
#define DP_LINK_TRAIN_PAT_IDLE (2 << 28)
#define DP_LINK_TRAIN_OFF (3 << 28)
#define DP_LINK_TRAIN_MASK (3 << 28)
#define DP_LINK_TRAIN_SHIFT 28
/* CPT Link training mode */
#define DP_LINK_TRAIN_PAT_1_CPT (0 << 8)
#define DP_LINK_TRAIN_PAT_2_CPT (1 << 8)
#define DP_LINK_TRAIN_PAT_IDLE_CPT (2 << 8)
#define DP_LINK_TRAIN_OFF_CPT (3 << 8)
#define DP_LINK_TRAIN_MASK_CPT (7 << 8)
#define DP_LINK_TRAIN_SHIFT_CPT 8
/* Signal voltages. These are mostly controlled by the other end */
#define DP_VOLTAGE_0_4 (0 << 25)
#define DP_VOLTAGE_0_6 (1 << 25)
#define DP_VOLTAGE_0_8 (2 << 25)
#define DP_VOLTAGE_1_2 (3 << 25)
#define DP_VOLTAGE_MASK (7 << 25)
#define DP_VOLTAGE_SHIFT 25
/* Signal pre-emphasis levels, like voltages, the other end tells us what
* they want
*/
#define DP_PRE_EMPHASIS_0 (0 << 22)
#define DP_PRE_EMPHASIS_3_5 (1 << 22)
#define DP_PRE_EMPHASIS_6 (2 << 22)
#define DP_PRE_EMPHASIS_9_5 (3 << 22)
#define DP_PRE_EMPHASIS_MASK (7 << 22)
#define DP_PRE_EMPHASIS_SHIFT 22
/* How many wires to use. I guess 3 was too hard */
#define DP_PORT_WIDTH_1 (0 << 19)
#define DP_PORT_WIDTH_2 (1 << 19)
#define DP_PORT_WIDTH_4 (3 << 19)
#define DP_PORT_WIDTH_MASK (7 << 19)
/* Mystic DPCD version 1.1 special mode */
#define DP_ENHANCED_FRAMING (1 << 18)
/* eDP */
#define DP_PLL_FREQ_270MHZ (0 << 16)
#define DP_PLL_FREQ_160MHZ (1 << 16)
#define DP_PLL_FREQ_MASK (3 << 16)
/** locked once port is enabled */
#define DP_PORT_REVERSAL (1 << 15)
/* eDP */
#define DP_PLL_ENABLE (1 << 14)
/** sends the clock on lane 15 of the PEG for debug */
#define DP_CLOCK_OUTPUT_ENABLE (1 << 13)
#define DP_SCRAMBLING_DISABLE (1 << 12)
#define DP_SCRAMBLING_DISABLE_IRONLAKE (1 << 7)
/** limit RGB values to avoid confusing TVs */
#define DP_COLOR_RANGE_16_235 (1 << 8)
/** Turn on the audio link */
#define DP_AUDIO_OUTPUT_ENABLE (1 << 6)
/** vs and hs sync polarity */
#define DP_SYNC_VS_HIGH (1 << 4)
#define DP_SYNC_HS_HIGH (1 << 3)
/** A fantasy */
#define DP_DETECTED (1 << 2)
/** The aux channel provides a way to talk to the
* signal sink for DDC etc. Max packet size supported
* is 20 bytes in each direction, hence the 5 fixed
* data registers
*/
#define DPA_AUX_CH_CTL 0x64010
#define DPA_AUX_CH_DATA1 0x64014
#define DPA_AUX_CH_DATA2 0x64018
#define DPA_AUX_CH_DATA3 0x6401c
#define DPA_AUX_CH_DATA4 0x64020
#define DPA_AUX_CH_DATA5 0x64024
#define DPB_AUX_CH_CTL 0x64110
#define DPB_AUX_CH_DATA1 0x64114
#define DPB_AUX_CH_DATA2 0x64118
#define DPB_AUX_CH_DATA3 0x6411c
#define DPB_AUX_CH_DATA4 0x64120
#define DPB_AUX_CH_DATA5 0x64124
#define DPC_AUX_CH_CTL 0x64210
#define DPC_AUX_CH_DATA1 0x64214
#define DPC_AUX_CH_DATA2 0x64218
#define DPC_AUX_CH_DATA3 0x6421c
#define DPC_AUX_CH_DATA4 0x64220
#define DPC_AUX_CH_DATA5 0x64224
#define DPD_AUX_CH_CTL 0x64310
#define DPD_AUX_CH_DATA1 0x64314
#define DPD_AUX_CH_DATA2 0x64318
#define DPD_AUX_CH_DATA3 0x6431c
#define DPD_AUX_CH_DATA4 0x64320
#define DPD_AUX_CH_DATA5 0x64324
#define DP_AUX_CH_CTL_SEND_BUSY (1 << 31)
#define DP_AUX_CH_CTL_DONE (1 << 30)
#define DP_AUX_CH_CTL_INTERRUPT (1 << 29)
#define DP_AUX_CH_CTL_TIME_OUT_ERROR (1 << 28)
#define DP_AUX_CH_CTL_TIME_OUT_400us (0 << 26)
#define DP_AUX_CH_CTL_TIME_OUT_600us (1 << 26)
#define DP_AUX_CH_CTL_TIME_OUT_800us (2 << 26)
#define DP_AUX_CH_CTL_TIME_OUT_1600us (3 << 26)
#define DP_AUX_CH_CTL_TIME_OUT_MASK (3 << 26)
#define DP_AUX_CH_CTL_RECEIVE_ERROR (1 << 25)
#define DP_AUX_CH_CTL_MESSAGE_SIZE_MASK (0x1f << 20)
#define DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT 20
#define DP_AUX_CH_CTL_PRECHARGE_2US_MASK (0xf << 16)
#define DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT 16
#define DP_AUX_CH_CTL_AUX_AKSV_SELECT (1 << 15)
#define DP_AUX_CH_CTL_MANCHESTER_TEST (1 << 14)
#define DP_AUX_CH_CTL_SYNC_TEST (1 << 13)
#define DP_AUX_CH_CTL_DEGLITCH_TEST (1 << 12)
#define DP_AUX_CH_CTL_PRECHARGE_TEST (1 << 11)
#define DP_AUX_CH_CTL_BIT_CLOCK_2X_MASK (0x7ff)
#define DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT 0
/*
* Computing GMCH M and N values for the Display Port link
*
* GMCH M/N = dot clock * bytes per pixel / ls_clk * # of lanes
*
* ls_clk (we assume) is the DP link clock (1.62 or 2.7 GHz)
*
* The GMCH value is used internally
*
* bytes_per_pixel is the number of bytes coming out of the plane,
* which is after the LUTs, so we want the bytes for our color format.
* For our current usage, this is always 3, one byte for R, G and B.
*/
#define PIPEA_GMCH_DATA_M 0x70050
#define PIPEB_GMCH_DATA_M 0x71050
/* Transfer unit size for display port - 1, default is 0x3f (for TU size 64) */
#define PIPE_GMCH_DATA_M_TU_SIZE_MASK (0x3f << 25)
#define PIPE_GMCH_DATA_M_TU_SIZE_SHIFT 25
#define PIPE_GMCH_DATA_M_MASK (0xffffff)
#define PIPEA_GMCH_DATA_N 0x70054
#define PIPEB_GMCH_DATA_N 0x71054
#define PIPE_GMCH_DATA_N_MASK (0xffffff)
/*
* Computing Link M and N values for the Display Port link
*
* Link M / N = pixel_clock / ls_clk
*
* (the DP spec calls pixel_clock the 'strm_clk')
*
* The Link value is transmitted in the Main Stream
* Attributes and VB-ID.
*/
#define PIPEA_DP_LINK_M 0x70060
#define PIPEB_DP_LINK_M 0x71060
#define PIPEA_DP_LINK_M_MASK (0xffffff)
#define PIPEA_DP_LINK_N 0x70064
#define PIPEB_DP_LINK_N 0x71064
#define PIPEA_DP_LINK_N_MASK (0xffffff)
/* Display & cursor control */
/* Pipe A */
#define PIPEADSL 0x70000
#define DSL_LINEMASK 0x00000fff
#define PIPEACONF 0x70008
#define PIPECONF_ENABLE (1<<31)
#define PIPECONF_DISABLE 0
#define PIPECONF_DOUBLE_WIDE (1<<30)
#define I965_PIPECONF_ACTIVE (1<<30)
#define PIPECONF_SINGLE_WIDE 0
#define PIPECONF_PIPE_UNLOCKED 0
#define PIPECONF_PIPE_LOCKED (1<<25)
#define PIPECONF_PALETTE 0
#define PIPECONF_GAMMA (1<<24)
#define PIPECONF_FORCE_BORDER (1<<25)
#define PIPECONF_PROGRESSIVE (0 << 21)
#define PIPECONF_INTERLACE_W_FIELD_INDICATION (6 << 21)
#define PIPECONF_INTERLACE_FIELD_0_ONLY (7 << 21)
#define PIPECONF_CXSR_DOWNCLOCK (1<<16)
#define PIPECONF_BPP_MASK (0x000000e0)
#define PIPECONF_BPP_8 (0<<5)
#define PIPECONF_BPP_10 (1<<5)
#define PIPECONF_BPP_6 (2<<5)
#define PIPECONF_BPP_12 (3<<5)
#define PIPECONF_DITHER_EN (1<<4)
#define PIPECONF_DITHER_TYPE_MASK (0x0000000c)
#define PIPECONF_DITHER_TYPE_SP (0<<2)
#define PIPECONF_DITHER_TYPE_ST1 (1<<2)
#define PIPECONF_DITHER_TYPE_ST2 (2<<2)
#define PIPECONF_DITHER_TYPE_TEMP (3<<2)
#define PIPEASTAT 0x70024
#define PIPE_FIFO_UNDERRUN_STATUS (1UL<<31)
#define PIPE_CRC_ERROR_ENABLE (1UL<<29)
#define PIPE_CRC_DONE_ENABLE (1UL<<28)
#define PIPE_GMBUS_EVENT_ENABLE (1UL<<27)
#define PIPE_HOTPLUG_INTERRUPT_ENABLE (1UL<<26)
#define PIPE_VSYNC_INTERRUPT_ENABLE (1UL<<25)
#define PIPE_DISPLAY_LINE_COMPARE_ENABLE (1UL<<24)
#define PIPE_DPST_EVENT_ENABLE (1UL<<23)
#define PIPE_LEGACY_BLC_EVENT_ENABLE (1UL<<22)
#define PIPE_ODD_FIELD_INTERRUPT_ENABLE (1UL<<21)
#define PIPE_EVEN_FIELD_INTERRUPT_ENABLE (1UL<<20)
#define PIPE_HOTPLUG_TV_INTERRUPT_ENABLE (1UL<<18) /* pre-965 */
#define PIPE_START_VBLANK_INTERRUPT_ENABLE (1UL<<18) /* 965 or later */
#define PIPE_VBLANK_INTERRUPT_ENABLE (1UL<<17)
#define PIPE_OVERLAY_UPDATED_ENABLE (1UL<<16)
#define PIPE_CRC_ERROR_INTERRUPT_STATUS (1UL<<13)
#define PIPE_CRC_DONE_INTERRUPT_STATUS (1UL<<12)
#define PIPE_GMBUS_INTERRUPT_STATUS (1UL<<11)
#define PIPE_HOTPLUG_INTERRUPT_STATUS (1UL<<10)
#define PIPE_VSYNC_INTERRUPT_STATUS (1UL<<9)
#define PIPE_DISPLAY_LINE_COMPARE_STATUS (1UL<<8)
#define PIPE_DPST_EVENT_STATUS (1UL<<7)
#define PIPE_LEGACY_BLC_EVENT_STATUS (1UL<<6)
#define PIPE_ODD_FIELD_INTERRUPT_STATUS (1UL<<5)
#define PIPE_EVEN_FIELD_INTERRUPT_STATUS (1UL<<4)
#define PIPE_HOTPLUG_TV_INTERRUPT_STATUS (1UL<<2) /* pre-965 */
#define PIPE_START_VBLANK_INTERRUPT_STATUS (1UL<<2) /* 965 or later */
#define PIPE_VBLANK_INTERRUPT_STATUS (1UL<<1)
#define PIPE_OVERLAY_UPDATED_STATUS (1UL<<0)
#define PIPE_BPC_MASK (7 << 5) /* Ironlake */
#define PIPE_8BPC (0 << 5)
#define PIPE_10BPC (1 << 5)
#define PIPE_6BPC (2 << 5)
#define PIPE_12BPC (3 << 5)
#define PIPECONF(pipe) _PIPE(pipe, PIPEACONF, PIPEBCONF)
#define PIPEDSL(pipe) _PIPE(pipe, PIPEADSL, PIPEBDSL)
#define DSPARB 0x70030
#define DSPARB_CSTART_MASK (0x7f << 7)
#define DSPARB_CSTART_SHIFT 7
#define DSPARB_BSTART_MASK (0x7f)
#define DSPARB_BSTART_SHIFT 0
#define DSPARB_BEND_SHIFT 9 /* on 855 */
#define DSPARB_AEND_SHIFT 0
#define DSPFW1 0x70034
#define DSPFW_SR_SHIFT 23
#define DSPFW_SR_MASK (0x1ff<<23)
#define DSPFW_CURSORB_SHIFT 16
#define DSPFW_CURSORB_MASK (0x3f<<16)
#define DSPFW_PLANEB_SHIFT 8
#define DSPFW_PLANEB_MASK (0x7f<<8)
#define DSPFW_PLANEA_MASK (0x7f)
#define DSPFW2 0x70038
#define DSPFW_CURSORA_MASK 0x00003f00
#define DSPFW_CURSORA_SHIFT 8
#define DSPFW_PLANEC_MASK (0x7f)
#define DSPFW3 0x7003c
#define DSPFW_HPLL_SR_EN (1<<31)
#define DSPFW_CURSOR_SR_SHIFT 24
#define PINEVIEW_SELF_REFRESH_EN (1<<30)
#define DSPFW_CURSOR_SR_MASK (0x3f<<24)
#define DSPFW_HPLL_CURSOR_SHIFT 16
#define DSPFW_HPLL_CURSOR_MASK (0x3f<<16)
#define DSPFW_HPLL_SR_MASK (0x1ff)
/* FIFO watermark sizes etc */
#define G4X_FIFO_LINE_SIZE 64
#define I915_FIFO_LINE_SIZE 64
#define I830_FIFO_LINE_SIZE 32
#define G4X_FIFO_SIZE 127
#define I965_FIFO_SIZE 512
#define I945_FIFO_SIZE 127
#define I915_FIFO_SIZE 95
#define I855GM_FIFO_SIZE 127 /* In cachelines */
#define I830_FIFO_SIZE 95
#define G4X_MAX_WM 0x3f
#define I915_MAX_WM 0x3f
#define PINEVIEW_DISPLAY_FIFO 512 /* in 64byte unit */
#define PINEVIEW_FIFO_LINE_SIZE 64
#define PINEVIEW_MAX_WM 0x1ff
#define PINEVIEW_DFT_WM 0x3f
#define PINEVIEW_DFT_HPLLOFF_WM 0
#define PINEVIEW_GUARD_WM 10
#define PINEVIEW_CURSOR_FIFO 64
#define PINEVIEW_CURSOR_MAX_WM 0x3f
#define PINEVIEW_CURSOR_DFT_WM 0
#define PINEVIEW_CURSOR_GUARD_WM 5
#define I965_CURSOR_FIFO 64
#define I965_CURSOR_MAX_WM 32
#define I965_CURSOR_DFT_WM 8
/* define the Watermark register on Ironlake */
#define WM0_PIPEA_ILK 0x45100
#define WM0_PIPE_PLANE_MASK (0x7f<<16)
#define WM0_PIPE_PLANE_SHIFT 16
#define WM0_PIPE_SPRITE_MASK (0x3f<<8)
#define WM0_PIPE_SPRITE_SHIFT 8
#define WM0_PIPE_CURSOR_MASK (0x1f)
#define WM0_PIPEB_ILK 0x45104
#define WM1_LP_ILK 0x45108
#define WM1_LP_SR_EN (1<<31)
#define WM1_LP_LATENCY_SHIFT 24
#define WM1_LP_LATENCY_MASK (0x7f<<24)
#define WM1_LP_FBC_MASK (0xf<<20)
#define WM1_LP_FBC_SHIFT 20
#define WM1_LP_SR_MASK (0x1ff<<8)
#define WM1_LP_SR_SHIFT 8
#define WM1_LP_CURSOR_MASK (0x3f)
#define WM2_LP_ILK 0x4510c
#define WM2_LP_EN (1<<31)
#define WM3_LP_ILK 0x45110
#define WM3_LP_EN (1<<31)
#define WM1S_LP_ILK 0x45120
#define WM1S_LP_EN (1<<31)
/* Memory latency timer register */
#define MLTR_ILK 0x11222
/* the unit of memory self-refresh latency time is 0.5us */
#define ILK_SRLT_MASK 0x3f
/* define the fifo size on Ironlake */
#define ILK_DISPLAY_FIFO 128
#define ILK_DISPLAY_MAXWM 64
#define ILK_DISPLAY_DFTWM 8
#define ILK_CURSOR_FIFO 32
#define ILK_CURSOR_MAXWM 16
#define ILK_CURSOR_DFTWM 8
#define ILK_DISPLAY_SR_FIFO 512
#define ILK_DISPLAY_MAX_SRWM 0x1ff
#define ILK_DISPLAY_DFT_SRWM 0x3f
#define ILK_CURSOR_SR_FIFO 64
#define ILK_CURSOR_MAX_SRWM 0x3f
#define ILK_CURSOR_DFT_SRWM 8
#define ILK_FIFO_LINE_SIZE 64
/*
* The two pipe frame counter registers are not synchronized, so
* reading a stable value is somewhat tricky. The following code
* should work:
*
* do {
* high1 = ((INREG(PIPEAFRAMEHIGH) & PIPE_FRAME_HIGH_MASK) >>
* PIPE_FRAME_HIGH_SHIFT;
* low1 = ((INREG(PIPEAFRAMEPIXEL) & PIPE_FRAME_LOW_MASK) >>
* PIPE_FRAME_LOW_SHIFT);
* high2 = ((INREG(PIPEAFRAMEHIGH) & PIPE_FRAME_HIGH_MASK) >>
* PIPE_FRAME_HIGH_SHIFT);
* } while (high1 != high2);
* frame = (high1 << 8) | low1;
*/
#define PIPEAFRAMEHIGH 0x70040
#define PIPE_FRAME_HIGH_MASK 0x0000ffff
#define PIPE_FRAME_HIGH_SHIFT 0
#define PIPEAFRAMEPIXEL 0x70044
#define PIPE_FRAME_LOW_MASK 0xff000000
#define PIPE_FRAME_LOW_SHIFT 24
#define PIPE_PIXEL_MASK 0x00ffffff
#define PIPE_PIXEL_SHIFT 0
/* GM45+ just has to be different */
#define PIPEA_FRMCOUNT_GM45 0x70040
#define PIPEA_FLIPCOUNT_GM45 0x70044
/* Cursor A & B regs */
#define CURACNTR 0x70080
/* Old style CUR*CNTR flags (desktop 8xx) */
#define CURSOR_ENABLE 0x80000000
#define CURSOR_GAMMA_ENABLE 0x40000000
#define CURSOR_STRIDE_MASK 0x30000000
#define CURSOR_FORMAT_SHIFT 24
#define CURSOR_FORMAT_MASK (0x07 << CURSOR_FORMAT_SHIFT)
#define CURSOR_FORMAT_2C (0x00 << CURSOR_FORMAT_SHIFT)
#define CURSOR_FORMAT_3C (0x01 << CURSOR_FORMAT_SHIFT)
#define CURSOR_FORMAT_4C (0x02 << CURSOR_FORMAT_SHIFT)
#define CURSOR_FORMAT_ARGB (0x04 << CURSOR_FORMAT_SHIFT)
#define CURSOR_FORMAT_XRGB (0x05 << CURSOR_FORMAT_SHIFT)
/* New style CUR*CNTR flags */
#define CURSOR_MODE 0x27
#define CURSOR_MODE_DISABLE 0x00
#define CURSOR_MODE_64_32B_AX 0x07
#define CURSOR_MODE_64_ARGB_AX ((1 << 5) | CURSOR_MODE_64_32B_AX)
#define MCURSOR_PIPE_SELECT (1 << 28)
#define MCURSOR_PIPE_A 0x00
#define MCURSOR_PIPE_B (1 << 28)
#define MCURSOR_GAMMA_ENABLE (1 << 26)
#define CURABASE 0x70084
#define CURAPOS 0x70088
#define CURSOR_POS_MASK 0x007FF
#define CURSOR_POS_SIGN 0x8000
#define CURSOR_X_SHIFT 0
#define CURSOR_Y_SHIFT 16
#define CURSIZE 0x700a0
#define CURBCNTR 0x700c0
#define CURBBASE 0x700c4
#define CURBPOS 0x700c8
/* Display A control */
#define DSPACNTR 0x70180
#define DISPLAY_PLANE_ENABLE (1<<31)
#define DISPLAY_PLANE_DISABLE 0
#define DISPPLANE_GAMMA_ENABLE (1<<30)
#define DISPPLANE_GAMMA_DISABLE 0
#define DISPPLANE_PIXFORMAT_MASK (0xf<<26)
#define DISPPLANE_8BPP (0x2<<26)
#define DISPPLANE_15_16BPP (0x4<<26)
#define DISPPLANE_16BPP (0x5<<26)
#define DISPPLANE_32BPP_NO_ALPHA (0x6<<26)
#define DISPPLANE_32BPP (0x7<<26)
#define DISPPLANE_32BPP_30BIT_NO_ALPHA (0xa<<26)
#define DISPPLANE_STEREO_ENABLE (1<<25)
#define DISPPLANE_STEREO_DISABLE 0
#define DISPPLANE_SEL_PIPE_MASK (1<<24)
#define DISPPLANE_SEL_PIPE_A 0
#define DISPPLANE_SEL_PIPE_B (1<<24)
#define DISPPLANE_SRC_KEY_ENABLE (1<<22)
#define DISPPLANE_SRC_KEY_DISABLE 0
#define DISPPLANE_LINE_DOUBLE (1<<20)
#define DISPPLANE_NO_LINE_DOUBLE 0
#define DISPPLANE_STEREO_POLARITY_FIRST 0
#define DISPPLANE_STEREO_POLARITY_SECOND (1<<18)
#define DISPPLANE_TRICKLE_FEED_DISABLE (1<<14) /* Ironlake */
#define DISPPLANE_TILED (1<<10)
#define DSPAADDR 0x70184
#define DSPASTRIDE 0x70188
#define DSPAPOS 0x7018C /* reserved */
#define DSPASIZE 0x70190
#define DSPASURF 0x7019C /* 965+ only */
#define DSPATILEOFF 0x701A4 /* 965+ only */
#define DSPCNTR(plane) _PIPE(plane, DSPACNTR, DSPBCNTR)
#define DSPADDR(plane) _PIPE(plane, DSPAADDR, DSPBADDR)
#define DSPSTRIDE(plane) _PIPE(plane, DSPASTRIDE, DSPBSTRIDE)
#define DSPPOS(plane) _PIPE(plane, DSPAPOS, DSPBPOS)
#define DSPSIZE(plane) _PIPE(plane, DSPASIZE, DSPBSIZE)
#define DSPSURF(plane) _PIPE(plane, DSPASURF, DSPBSURF)
#define DSPTILEOFF(plane) _PIPE(plane, DSPATILEOFF, DSPBTILEOFF)
/* VBIOS flags */
#define SWF00 0x71410
#define SWF01 0x71414
#define SWF02 0x71418
#define SWF03 0x7141c
#define SWF04 0x71420
#define SWF05 0x71424
#define SWF06 0x71428
#define SWF10 0x70410
#define SWF11 0x70414
#define SWF14 0x71420
#define SWF30 0x72414
#define SWF31 0x72418
#define SWF32 0x7241c
/* Pipe B */
#define PIPEBDSL 0x71000
#define PIPEBCONF 0x71008
#define PIPEBSTAT 0x71024
#define PIPEBFRAMEHIGH 0x71040
#define PIPEBFRAMEPIXEL 0x71044
#define PIPEB_FRMCOUNT_GM45 0x71040
#define PIPEB_FLIPCOUNT_GM45 0x71044
/* Display B control */
#define DSPBCNTR 0x71180
#define DISPPLANE_ALPHA_TRANS_ENABLE (1<<15)
#define DISPPLANE_ALPHA_TRANS_DISABLE 0
#define DISPPLANE_SPRITE_ABOVE_DISPLAY 0
#define DISPPLANE_SPRITE_ABOVE_OVERLAY (1)
#define DSPBADDR 0x71184
#define DSPBSTRIDE 0x71188
#define DSPBPOS 0x7118C
#define DSPBSIZE 0x71190
#define DSPBSURF 0x7119C
#define DSPBTILEOFF 0x711A4
/* VBIOS regs */
#define VGACNTRL 0x71400
# define VGA_DISP_DISABLE (1 << 31)
# define VGA_2X_MODE (1 << 30)
# define VGA_PIPE_B_SELECT (1 << 29)
/* Ironlake */
#define CPU_VGACNTRL 0x41000
#define DIGITAL_PORT_HOTPLUG_CNTRL 0x44030
#define DIGITAL_PORTA_HOTPLUG_ENABLE (1 << 4)
#define DIGITAL_PORTA_SHORT_PULSE_2MS (0 << 2)
#define DIGITAL_PORTA_SHORT_PULSE_4_5MS (1 << 2)
#define DIGITAL_PORTA_SHORT_PULSE_6MS (2 << 2)
#define DIGITAL_PORTA_SHORT_PULSE_100MS (3 << 2)
#define DIGITAL_PORTA_NO_DETECT (0 << 0)
#define DIGITAL_PORTA_LONG_PULSE_DETECT_MASK (1 << 1)
#define DIGITAL_PORTA_SHORT_PULSE_DETECT_MASK (1 << 0)
/* refresh rate hardware control */
#define RR_HW_CTL 0x45300
#define RR_HW_LOW_POWER_FRAMES_MASK 0xff
#define RR_HW_HIGH_POWER_FRAMES_MASK 0xff00
#define FDI_PLL_BIOS_0 0x46000
#define FDI_PLL_FB_CLOCK_MASK 0xff
#define FDI_PLL_BIOS_1 0x46004
#define FDI_PLL_BIOS_2 0x46008
#define DISPLAY_PORT_PLL_BIOS_0 0x4600c
#define DISPLAY_PORT_PLL_BIOS_1 0x46010
#define DISPLAY_PORT_PLL_BIOS_2 0x46014
#define PCH_DSPCLK_GATE_D 0x42020
# define DPFDUNIT_CLOCK_GATE_DISABLE (1 << 7)
# define DPARBUNIT_CLOCK_GATE_DISABLE (1 << 5)
#define PCH_3DCGDIS0 0x46020
# define MARIUNIT_CLOCK_GATE_DISABLE (1 << 18)
# define SVSMUNIT_CLOCK_GATE_DISABLE (1 << 1)
#define FDI_PLL_FREQ_CTL 0x46030
#define FDI_PLL_FREQ_CHANGE_REQUEST (1<<24)
#define FDI_PLL_FREQ_LOCK_LIMIT_MASK 0xfff00
#define FDI_PLL_FREQ_DISABLE_COUNT_LIMIT_MASK 0xff
#define PIPEA_DATA_M1 0x60030
#define TU_SIZE(x) (((x)-1) << 25) /* default size 64 */
#define TU_SIZE_MASK 0x7e000000
#define PIPE_DATA_M1_OFFSET 0
#define PIPEA_DATA_N1 0x60034
#define PIPE_DATA_N1_OFFSET 0
#define PIPEA_DATA_M2 0x60038
#define PIPE_DATA_M2_OFFSET 0
#define PIPEA_DATA_N2 0x6003c
#define PIPE_DATA_N2_OFFSET 0
#define PIPEA_LINK_M1 0x60040
#define PIPE_LINK_M1_OFFSET 0
#define PIPEA_LINK_N1 0x60044
#define PIPE_LINK_N1_OFFSET 0
#define PIPEA_LINK_M2 0x60048
#define PIPE_LINK_M2_OFFSET 0
#define PIPEA_LINK_N2 0x6004c
#define PIPE_LINK_N2_OFFSET 0
/* PIPEB timing regs are same start from 0x61000 */
#define PIPEB_DATA_M1 0x61030
#define PIPEB_DATA_N1 0x61034
#define PIPEB_DATA_M2 0x61038
#define PIPEB_DATA_N2 0x6103c
#define PIPEB_LINK_M1 0x61040
#define PIPEB_LINK_N1 0x61044
#define PIPEB_LINK_M2 0x61048
#define PIPEB_LINK_N2 0x6104c
#define PIPE_DATA_M1(pipe) _PIPE(pipe, PIPEA_DATA_M1, PIPEB_DATA_M1)
#define PIPE_DATA_N1(pipe) _PIPE(pipe, PIPEA_DATA_N1, PIPEB_DATA_N1)
#define PIPE_DATA_M2(pipe) _PIPE(pipe, PIPEA_DATA_M2, PIPEB_DATA_M2)
#define PIPE_DATA_N2(pipe) _PIPE(pipe, PIPEA_DATA_N2, PIPEB_DATA_N2)
#define PIPE_LINK_M1(pipe) _PIPE(pipe, PIPEA_LINK_M1, PIPEB_LINK_M1)
#define PIPE_LINK_N1(pipe) _PIPE(pipe, PIPEA_LINK_N1, PIPEB_LINK_N1)
#define PIPE_LINK_M2(pipe) _PIPE(pipe, PIPEA_LINK_M2, PIPEB_LINK_M2)
#define PIPE_LINK_N2(pipe) _PIPE(pipe, PIPEA_LINK_N2, PIPEB_LINK_N2)
/* CPU panel fitter */
#define PFA_CTL_1 0x68080
#define PFB_CTL_1 0x68880
#define PF_ENABLE (1<<31)
#define PF_FILTER_MASK (3<<23)
#define PF_FILTER_PROGRAMMED (0<<23)
#define PF_FILTER_MED_3x3 (1<<23)
#define PF_FILTER_EDGE_ENHANCE (2<<23)
#define PF_FILTER_EDGE_SOFTEN (3<<23)
#define PFA_WIN_SZ 0x68074
#define PFB_WIN_SZ 0x68874
#define PFA_WIN_POS 0x68070
#define PFB_WIN_POS 0x68870
/* legacy palette */
#define LGC_PALETTE_A 0x4a000
#define LGC_PALETTE_B 0x4a800
/* interrupts */
#define DE_MASTER_IRQ_CONTROL (1 << 31)
#define DE_SPRITEB_FLIP_DONE (1 << 29)
#define DE_SPRITEA_FLIP_DONE (1 << 28)
#define DE_PLANEB_FLIP_DONE (1 << 27)
#define DE_PLANEA_FLIP_DONE (1 << 26)
#define DE_PCU_EVENT (1 << 25)
#define DE_GTT_FAULT (1 << 24)
#define DE_POISON (1 << 23)
#define DE_PERFORM_COUNTER (1 << 22)
#define DE_PCH_EVENT (1 << 21)
#define DE_AUX_CHANNEL_A (1 << 20)
#define DE_DP_A_HOTPLUG (1 << 19)
#define DE_GSE (1 << 18)
#define DE_PIPEB_VBLANK (1 << 15)
#define DE_PIPEB_EVEN_FIELD (1 << 14)
#define DE_PIPEB_ODD_FIELD (1 << 13)
#define DE_PIPEB_LINE_COMPARE (1 << 12)
#define DE_PIPEB_VSYNC (1 << 11)
#define DE_PIPEB_FIFO_UNDERRUN (1 << 8)
#define DE_PIPEA_VBLANK (1 << 7)
#define DE_PIPEA_EVEN_FIELD (1 << 6)
#define DE_PIPEA_ODD_FIELD (1 << 5)
#define DE_PIPEA_LINE_COMPARE (1 << 4)
#define DE_PIPEA_VSYNC (1 << 3)
#define DE_PIPEA_FIFO_UNDERRUN (1 << 0)
#define DEISR 0x44000
#define DEIMR 0x44004
#define DEIIR 0x44008
#define DEIER 0x4400c
/* GT interrupt */
#define GT_PIPE_NOTIFY (1 << 4)
#define GT_SYNC_STATUS (1 << 2)
#define GT_USER_INTERRUPT (1 << 0)
#define GT_BSD_USER_INTERRUPT (1 << 5)
#define GT_GEN6_BSD_USER_INTERRUPT (1 << 12)
#define GTISR 0x44010
#define GTIMR 0x44014
#define GTIIR 0x44018
#define GTIER 0x4401c
#define ILK_DISPLAY_CHICKEN2 0x42004
#define ILK_DPARB_GATE (1<<22)
#define ILK_VSDPFD_FULL (1<<21)
#define ILK_DSPCLK_GATE 0x42020
#define ILK_DPARB_CLK_GATE (1<<5)
/* According to spec this bit 7/8/9 of 0x42020 should be set to enable FBC */
#define ILK_CLK_FBC (1<<7)
#define ILK_DPFC_DIS1 (1<<8)
#define ILK_DPFC_DIS2 (1<<9)
#define DISP_ARB_CTL 0x45000
#define DISP_TILE_SURFACE_SWIZZLING (1<<13)
#define DISP_FBC_WM_DIS (1<<15)
/* PCH */
/* south display engine interrupt */
#define SDE_CRT_HOTPLUG (1 << 11)
#define SDE_PORTD_HOTPLUG (1 << 10)
#define SDE_PORTC_HOTPLUG (1 << 9)
#define SDE_PORTB_HOTPLUG (1 << 8)
#define SDE_SDVOB_HOTPLUG (1 << 6)
#define SDE_HOTPLUG_MASK (0xf << 8)
/* CPT */
#define SDE_CRT_HOTPLUG_CPT (1 << 19)
#define SDE_PORTD_HOTPLUG_CPT (1 << 23)
#define SDE_PORTC_HOTPLUG_CPT (1 << 22)
#define SDE_PORTB_HOTPLUG_CPT (1 << 21)
#define SDEISR 0xc4000
#define SDEIMR 0xc4004
#define SDEIIR 0xc4008
#define SDEIER 0xc400c
/* digital port hotplug */
#define PCH_PORT_HOTPLUG 0xc4030
#define PORTD_HOTPLUG_ENABLE (1 << 20)
#define PORTD_PULSE_DURATION_2ms (0)
#define PORTD_PULSE_DURATION_4_5ms (1 << 18)
#define PORTD_PULSE_DURATION_6ms (2 << 18)
#define PORTD_PULSE_DURATION_100ms (3 << 18)
#define PORTD_HOTPLUG_NO_DETECT (0)
#define PORTD_HOTPLUG_SHORT_DETECT (1 << 16)
#define PORTD_HOTPLUG_LONG_DETECT (1 << 17)
#define PORTC_HOTPLUG_ENABLE (1 << 12)
#define PORTC_PULSE_DURATION_2ms (0)
#define PORTC_PULSE_DURATION_4_5ms (1 << 10)
#define PORTC_PULSE_DURATION_6ms (2 << 10)
#define PORTC_PULSE_DURATION_100ms (3 << 10)
#define PORTC_HOTPLUG_NO_DETECT (0)
#define PORTC_HOTPLUG_SHORT_DETECT (1 << 8)
#define PORTC_HOTPLUG_LONG_DETECT (1 << 9)
#define PORTB_HOTPLUG_ENABLE (1 << 4)
#define PORTB_PULSE_DURATION_2ms (0)
#define PORTB_PULSE_DURATION_4_5ms (1 << 2)
#define PORTB_PULSE_DURATION_6ms (2 << 2)
#define PORTB_PULSE_DURATION_100ms (3 << 2)
#define PORTB_HOTPLUG_NO_DETECT (0)
#define PORTB_HOTPLUG_SHORT_DETECT (1 << 0)
#define PORTB_HOTPLUG_LONG_DETECT (1 << 1)
#define PCH_GPIOA 0xc5010
#define PCH_GPIOB 0xc5014
#define PCH_GPIOC 0xc5018
#define PCH_GPIOD 0xc501c
#define PCH_GPIOE 0xc5020
#define PCH_GPIOF 0xc5024
#define PCH_GMBUS0 0xc5100
#define PCH_GMBUS1 0xc5104
#define PCH_GMBUS2 0xc5108
#define PCH_GMBUS3 0xc510c
#define PCH_GMBUS4 0xc5110
#define PCH_GMBUS5 0xc5120
#define PCH_DPLL_A 0xc6014
#define PCH_DPLL_B 0xc6018
#define PCH_DPLL(pipe) _PIPE(pipe, PCH_DPLL_A, PCH_DPLL_B)
#define PCH_FPA0 0xc6040
#define PCH_FPA1 0xc6044
#define PCH_FPB0 0xc6048
#define PCH_FPB1 0xc604c
#define PCH_FP0(pipe) _PIPE(pipe, PCH_FPA0, PCH_FPB0)
#define PCH_FP1(pipe) _PIPE(pipe, PCH_FPA1, PCH_FPB1)
#define PCH_DPLL_TEST 0xc606c
#define PCH_DREF_CONTROL 0xC6200
#define DREF_CONTROL_MASK 0x7fc3
#define DREF_CPU_SOURCE_OUTPUT_DISABLE (0<<13)
#define DREF_CPU_SOURCE_OUTPUT_DOWNSPREAD (2<<13)
#define DREF_CPU_SOURCE_OUTPUT_NONSPREAD (3<<13)
#define DREF_CPU_SOURCE_OUTPUT_MASK (3<<13)
#define DREF_SSC_SOURCE_DISABLE (0<<11)
#define DREF_SSC_SOURCE_ENABLE (2<<11)
#define DREF_SSC_SOURCE_MASK (3<<11)
#define DREF_NONSPREAD_SOURCE_DISABLE (0<<9)
#define DREF_NONSPREAD_CK505_ENABLE (1<<9)
#define DREF_NONSPREAD_SOURCE_ENABLE (2<<9)
#define DREF_NONSPREAD_SOURCE_MASK (3<<9)
#define DREF_SUPERSPREAD_SOURCE_DISABLE (0<<7)
#define DREF_SUPERSPREAD_SOURCE_ENABLE (2<<7)
#define DREF_SSC4_DOWNSPREAD (0<<6)
#define DREF_SSC4_CENTERSPREAD (1<<6)
#define DREF_SSC1_DISABLE (0<<1)
#define DREF_SSC1_ENABLE (1<<1)
#define DREF_SSC4_DISABLE (0)
#define DREF_SSC4_ENABLE (1)
#define PCH_RAWCLK_FREQ 0xc6204
#define FDL_TP1_TIMER_SHIFT 12
#define FDL_TP1_TIMER_MASK (3<<12)
#define FDL_TP2_TIMER_SHIFT 10
#define FDL_TP2_TIMER_MASK (3<<10)
#define RAWCLK_FREQ_MASK 0x3ff
#define PCH_DPLL_TMR_CFG 0xc6208
#define PCH_SSC4_PARMS 0xc6210
#define PCH_SSC4_AUX_PARMS 0xc6214
#define PCH_DPLL_SEL 0xc7000
#define TRANSA_DPLL_ENABLE (1<<3)
#define TRANSA_DPLLB_SEL (1<<0)
#define TRANSA_DPLLA_SEL 0
#define TRANSB_DPLL_ENABLE (1<<7)
#define TRANSB_DPLLB_SEL (1<<4)
#define TRANSB_DPLLA_SEL (0)
#define TRANSC_DPLL_ENABLE (1<<11)
#define TRANSC_DPLLB_SEL (1<<8)
#define TRANSC_DPLLA_SEL (0)
/* transcoder */
#define TRANS_HTOTAL_A 0xe0000
#define TRANS_HTOTAL_SHIFT 16
#define TRANS_HACTIVE_SHIFT 0
#define TRANS_HBLANK_A 0xe0004
#define TRANS_HBLANK_END_SHIFT 16
#define TRANS_HBLANK_START_SHIFT 0
#define TRANS_HSYNC_A 0xe0008
#define TRANS_HSYNC_END_SHIFT 16
#define TRANS_HSYNC_START_SHIFT 0
#define TRANS_VTOTAL_A 0xe000c
#define TRANS_VTOTAL_SHIFT 16
#define TRANS_VACTIVE_SHIFT 0
#define TRANS_VBLANK_A 0xe0010
#define TRANS_VBLANK_END_SHIFT 16
#define TRANS_VBLANK_START_SHIFT 0
#define TRANS_VSYNC_A 0xe0014
#define TRANS_VSYNC_END_SHIFT 16
#define TRANS_VSYNC_START_SHIFT 0
#define TRANSA_DATA_M1 0xe0030
#define TRANSA_DATA_N1 0xe0034
#define TRANSA_DATA_M2 0xe0038
#define TRANSA_DATA_N2 0xe003c
#define TRANSA_DP_LINK_M1 0xe0040
#define TRANSA_DP_LINK_N1 0xe0044
#define TRANSA_DP_LINK_M2 0xe0048
#define TRANSA_DP_LINK_N2 0xe004c
#define TRANS_HTOTAL_B 0xe1000
#define TRANS_HBLANK_B 0xe1004
#define TRANS_HSYNC_B 0xe1008
#define TRANS_VTOTAL_B 0xe100c
#define TRANS_VBLANK_B 0xe1010
#define TRANS_VSYNC_B 0xe1014
#define TRANS_HTOTAL(pipe) _PIPE(pipe, TRANS_HTOTAL_A, TRANS_HTOTAL_B)
#define TRANS_HBLANK(pipe) _PIPE(pipe, TRANS_HBLANK_A, TRANS_HBLANK_B)
#define TRANS_HSYNC(pipe) _PIPE(pipe, TRANS_HSYNC_A, TRANS_HSYNC_B)
#define TRANS_VTOTAL(pipe) _PIPE(pipe, TRANS_VTOTAL_A, TRANS_VTOTAL_B)
#define TRANS_VBLANK(pipe) _PIPE(pipe, TRANS_VBLANK_A, TRANS_VBLANK_B)
#define TRANS_VSYNC(pipe) _PIPE(pipe, TRANS_VSYNC_A, TRANS_VSYNC_B)
#define TRANSB_DATA_M1 0xe1030
#define TRANSB_DATA_N1 0xe1034
#define TRANSB_DATA_M2 0xe1038
#define TRANSB_DATA_N2 0xe103c
#define TRANSB_DP_LINK_M1 0xe1040
#define TRANSB_DP_LINK_N1 0xe1044
#define TRANSB_DP_LINK_M2 0xe1048
#define TRANSB_DP_LINK_N2 0xe104c
#define TRANSACONF 0xf0008
#define TRANSBCONF 0xf1008
#define TRANSCONF(plane) _PIPE(plane, TRANSACONF, TRANSBCONF)
#define TRANS_DISABLE (0<<31)
#define TRANS_ENABLE (1<<31)
#define TRANS_STATE_MASK (1<<30)
#define TRANS_STATE_DISABLE (0<<30)
#define TRANS_STATE_ENABLE (1<<30)
#define TRANS_FSYNC_DELAY_HB1 (0<<27)
#define TRANS_FSYNC_DELAY_HB2 (1<<27)
#define TRANS_FSYNC_DELAY_HB3 (2<<27)
#define TRANS_FSYNC_DELAY_HB4 (3<<27)
#define TRANS_DP_AUDIO_ONLY (1<<26)
#define TRANS_DP_VIDEO_AUDIO (0<<26)
#define TRANS_PROGRESSIVE (0<<21)
#define TRANS_8BPC (0<<5)
#define TRANS_10BPC (1<<5)
#define TRANS_6BPC (2<<5)
#define TRANS_12BPC (3<<5)
#define FDI_RXA_CHICKEN 0xc200c
#define FDI_RXB_CHICKEN 0xc2010
#define FDI_RX_PHASE_SYNC_POINTER_ENABLE (1)
#define FDI_RX_CHICKEN(pipe) _PIPE(pipe, FDI_RXA_CHICKEN, FDI_RXB_CHICKEN)
#define SOUTH_DSPCLK_GATE_D 0xc2020
#define PCH_DPLSUNIT_CLOCK_GATE_DISABLE (1<<29)
/* CPU: FDI_TX */
#define FDI_TXA_CTL 0x60100
#define FDI_TXB_CTL 0x61100
#define FDI_TX_CTL(pipe) _PIPE(pipe, FDI_TXA_CTL, FDI_TXB_CTL)
#define FDI_TX_DISABLE (0<<31)
#define FDI_TX_ENABLE (1<<31)
#define FDI_LINK_TRAIN_PATTERN_1 (0<<28)
#define FDI_LINK_TRAIN_PATTERN_2 (1<<28)
#define FDI_LINK_TRAIN_PATTERN_IDLE (2<<28)
#define FDI_LINK_TRAIN_NONE (3<<28)
#define FDI_LINK_TRAIN_VOLTAGE_0_4V (0<<25)
#define FDI_LINK_TRAIN_VOLTAGE_0_6V (1<<25)
#define FDI_LINK_TRAIN_VOLTAGE_0_8V (2<<25)
#define FDI_LINK_TRAIN_VOLTAGE_1_2V (3<<25)
#define FDI_LINK_TRAIN_PRE_EMPHASIS_NONE (0<<22)
#define FDI_LINK_TRAIN_PRE_EMPHASIS_1_5X (1<<22)
#define FDI_LINK_TRAIN_PRE_EMPHASIS_2X (2<<22)
#define FDI_LINK_TRAIN_PRE_EMPHASIS_3X (3<<22)
/* ILK always use 400mV 0dB for voltage swing and pre-emphasis level.
SNB has different settings. */
/* SNB A-stepping */
#define FDI_LINK_TRAIN_400MV_0DB_SNB_A (0x38<<22)
#define FDI_LINK_TRAIN_400MV_6DB_SNB_A (0x02<<22)
#define FDI_LINK_TRAIN_600MV_3_5DB_SNB_A (0x01<<22)
#define FDI_LINK_TRAIN_800MV_0DB_SNB_A (0x0<<22)
/* SNB B-stepping */
#define FDI_LINK_TRAIN_400MV_0DB_SNB_B (0x0<<22)
#define FDI_LINK_TRAIN_400MV_6DB_SNB_B (0x3a<<22)
#define FDI_LINK_TRAIN_600MV_3_5DB_SNB_B (0x39<<22)
#define FDI_LINK_TRAIN_800MV_0DB_SNB_B (0x38<<22)
#define FDI_LINK_TRAIN_VOL_EMP_MASK (0x3f<<22)
#define FDI_DP_PORT_WIDTH_X1 (0<<19)
#define FDI_DP_PORT_WIDTH_X2 (1<<19)
#define FDI_DP_PORT_WIDTH_X3 (2<<19)
#define FDI_DP_PORT_WIDTH_X4 (3<<19)
#define FDI_TX_ENHANCE_FRAME_ENABLE (1<<18)
/* Ironlake: hardwired to 1 */
#define FDI_TX_PLL_ENABLE (1<<14)
/* both Tx and Rx */
#define FDI_SCRAMBLING_ENABLE (0<<7)
#define FDI_SCRAMBLING_DISABLE (1<<7)
/* FDI_RX, FDI_X is hard-wired to Transcoder_X */
#define FDI_RXA_CTL 0xf000c
#define FDI_RXB_CTL 0xf100c
#define FDI_RX_CTL(pipe) _PIPE(pipe, FDI_RXA_CTL, FDI_RXB_CTL)
#define FDI_RX_ENABLE (1<<31)
/* train, dp width same as FDI_TX */
#define FDI_DP_PORT_WIDTH_X8 (7<<19)
#define FDI_8BPC (0<<16)
#define FDI_10BPC (1<<16)
#define FDI_6BPC (2<<16)
#define FDI_12BPC (3<<16)
#define FDI_LINK_REVERSE_OVERWRITE (1<<15)
#define FDI_DMI_LINK_REVERSE_MASK (1<<14)
#define FDI_RX_PLL_ENABLE (1<<13)
#define FDI_FS_ERR_CORRECT_ENABLE (1<<11)
#define FDI_FE_ERR_CORRECT_ENABLE (1<<10)
#define FDI_FS_ERR_REPORT_ENABLE (1<<9)
#define FDI_FE_ERR_REPORT_ENABLE (1<<8)
#define FDI_RX_ENHANCE_FRAME_ENABLE (1<<6)
#define FDI_PCDCLK (1<<4)
/* CPT */
#define FDI_AUTO_TRAINING (1<<10)
#define FDI_LINK_TRAIN_PATTERN_1_CPT (0<<8)
#define FDI_LINK_TRAIN_PATTERN_2_CPT (1<<8)
#define FDI_LINK_TRAIN_PATTERN_IDLE_CPT (2<<8)
#define FDI_LINK_TRAIN_NORMAL_CPT (3<<8)
#define FDI_LINK_TRAIN_PATTERN_MASK_CPT (3<<8)
#define FDI_RXA_MISC 0xf0010
#define FDI_RXB_MISC 0xf1010
#define FDI_RXA_TUSIZE1 0xf0030
#define FDI_RXA_TUSIZE2 0xf0038
#define FDI_RXB_TUSIZE1 0xf1030
#define FDI_RXB_TUSIZE2 0xf1038
#define FDI_RX_MISC(pipe) _PIPE(pipe, FDI_RXA_MISC, FDI_RXB_MISC)
#define FDI_RX_TUSIZE1(pipe) _PIPE(pipe, FDI_RXA_TUSIZE1, FDI_RXB_TUSIZE1)
#define FDI_RX_TUSIZE2(pipe) _PIPE(pipe, FDI_RXA_TUSIZE2, FDI_RXB_TUSIZE2)
/* FDI_RX interrupt register format */
#define FDI_RX_INTER_LANE_ALIGN (1<<10)
#define FDI_RX_SYMBOL_LOCK (1<<9) /* train 2 */
#define FDI_RX_BIT_LOCK (1<<8) /* train 1 */
#define FDI_RX_TRAIN_PATTERN_2_FAIL (1<<7)
#define FDI_RX_FS_CODE_ERR (1<<6)
#define FDI_RX_FE_CODE_ERR (1<<5)
#define FDI_RX_SYMBOL_ERR_RATE_ABOVE (1<<4)
#define FDI_RX_HDCP_LINK_FAIL (1<<3)
#define FDI_RX_PIXEL_FIFO_OVERFLOW (1<<2)
#define FDI_RX_CROSS_CLOCK_OVERFLOW (1<<1)
#define FDI_RX_SYMBOL_QUEUE_OVERFLOW (1<<0)
#define FDI_RXA_IIR 0xf0014
#define FDI_RXA_IMR 0xf0018
#define FDI_RXB_IIR 0xf1014
#define FDI_RXB_IMR 0xf1018
#define FDI_RX_IIR(pipe) _PIPE(pipe, FDI_RXA_IIR, FDI_RXB_IIR)
#define FDI_RX_IMR(pipe) _PIPE(pipe, FDI_RXA_IMR, FDI_RXB_IMR)
#define FDI_PLL_CTL_1 0xfe000
#define FDI_PLL_CTL_2 0xfe004
/* CRT */
#define PCH_ADPA 0xe1100
#define ADPA_TRANS_SELECT_MASK (1<<30)
#define ADPA_TRANS_A_SELECT 0
#define ADPA_TRANS_B_SELECT (1<<30)
#define ADPA_CRT_HOTPLUG_MASK 0x03ff0000 /* bit 25-16 */
#define ADPA_CRT_HOTPLUG_MONITOR_NONE (0<<24)
#define ADPA_CRT_HOTPLUG_MONITOR_MASK (3<<24)
#define ADPA_CRT_HOTPLUG_MONITOR_COLOR (3<<24)
#define ADPA_CRT_HOTPLUG_MONITOR_MONO (2<<24)
#define ADPA_CRT_HOTPLUG_ENABLE (1<<23)
#define ADPA_CRT_HOTPLUG_PERIOD_64 (0<<22)
#define ADPA_CRT_HOTPLUG_PERIOD_128 (1<<22)
#define ADPA_CRT_HOTPLUG_WARMUP_5MS (0<<21)
#define ADPA_CRT_HOTPLUG_WARMUP_10MS (1<<21)
#define ADPA_CRT_HOTPLUG_SAMPLE_2S (0<<20)
#define ADPA_CRT_HOTPLUG_SAMPLE_4S (1<<20)
#define ADPA_CRT_HOTPLUG_VOLTAGE_40 (0<<18)
#define ADPA_CRT_HOTPLUG_VOLTAGE_50 (1<<18)
#define ADPA_CRT_HOTPLUG_VOLTAGE_60 (2<<18)
#define ADPA_CRT_HOTPLUG_VOLTAGE_70 (3<<18)
#define ADPA_CRT_HOTPLUG_VOLREF_325MV (0<<17)
#define ADPA_CRT_HOTPLUG_VOLREF_475MV (1<<17)
#define ADPA_CRT_HOTPLUG_FORCE_TRIGGER (1<<16)
/* or SDVOB */
#define HDMIB 0xe1140
#define PORT_ENABLE (1 << 31)
#define TRANSCODER_A (0)
#define TRANSCODER_B (1 << 30)
#define COLOR_FORMAT_8bpc (0)
#define COLOR_FORMAT_12bpc (3 << 26)
#define SDVOB_HOTPLUG_ENABLE (1 << 23)
#define SDVO_ENCODING (0)
#define TMDS_ENCODING (2 << 10)
#define NULL_PACKET_VSYNC_ENABLE (1 << 9)
/* CPT */
#define HDMI_MODE_SELECT (1 << 9)
#define DVI_MODE_SELECT (0)
#define SDVOB_BORDER_ENABLE (1 << 7)
#define AUDIO_ENABLE (1 << 6)
#define VSYNC_ACTIVE_HIGH (1 << 4)
#define HSYNC_ACTIVE_HIGH (1 << 3)
#define PORT_DETECTED (1 << 2)
/* PCH SDVOB multiplex with HDMIB */
#define PCH_SDVOB HDMIB
#define HDMIC 0xe1150
#define HDMID 0xe1160
#define PCH_LVDS 0xe1180
#define LVDS_DETECTED (1 << 1)
#define BLC_PWM_CPU_CTL2 0x48250
#define PWM_ENABLE (1 << 31)
#define PWM_PIPE_A (0 << 29)
#define PWM_PIPE_B (1 << 29)
#define BLC_PWM_CPU_CTL 0x48254
#define BLC_PWM_PCH_CTL1 0xc8250
#define PWM_PCH_ENABLE (1 << 31)
#define PWM_POLARITY_ACTIVE_LOW (1 << 29)
#define PWM_POLARITY_ACTIVE_HIGH (0 << 29)
#define PWM_POLARITY_ACTIVE_LOW2 (1 << 28)
#define PWM_POLARITY_ACTIVE_HIGH2 (0 << 28)
#define BLC_PWM_PCH_CTL2 0xc8254
#define PCH_PP_STATUS 0xc7200
#define PCH_PP_CONTROL 0xc7204
#define PANEL_UNLOCK_REGS (0xabcd << 16)
#define EDP_FORCE_VDD (1 << 3)
#define EDP_BLC_ENABLE (1 << 2)
#define PANEL_POWER_RESET (1 << 1)
#define PANEL_POWER_OFF (0 << 0)
#define PANEL_POWER_ON (1 << 0)
#define PCH_PP_ON_DELAYS 0xc7208
#define EDP_PANEL (1 << 30)
#define PCH_PP_OFF_DELAYS 0xc720c
#define PCH_PP_DIVISOR 0xc7210
#define PCH_DP_B 0xe4100
#define PCH_DPB_AUX_CH_CTL 0xe4110
#define PCH_DPB_AUX_CH_DATA1 0xe4114
#define PCH_DPB_AUX_CH_DATA2 0xe4118
#define PCH_DPB_AUX_CH_DATA3 0xe411c
#define PCH_DPB_AUX_CH_DATA4 0xe4120
#define PCH_DPB_AUX_CH_DATA5 0xe4124
#define PCH_DP_C 0xe4200
#define PCH_DPC_AUX_CH_CTL 0xe4210
#define PCH_DPC_AUX_CH_DATA1 0xe4214
#define PCH_DPC_AUX_CH_DATA2 0xe4218
#define PCH_DPC_AUX_CH_DATA3 0xe421c
#define PCH_DPC_AUX_CH_DATA4 0xe4220
#define PCH_DPC_AUX_CH_DATA5 0xe4224
#define PCH_DP_D 0xe4300
#define PCH_DPD_AUX_CH_CTL 0xe4310
#define PCH_DPD_AUX_CH_DATA1 0xe4314
#define PCH_DPD_AUX_CH_DATA2 0xe4318
#define PCH_DPD_AUX_CH_DATA3 0xe431c
#define PCH_DPD_AUX_CH_DATA4 0xe4320
#define PCH_DPD_AUX_CH_DATA5 0xe4324
/* CPT */
#define PORT_TRANS_A_SEL_CPT 0
#define PORT_TRANS_B_SEL_CPT (1<<29)
#define PORT_TRANS_C_SEL_CPT (2<<29)
#define PORT_TRANS_SEL_MASK (3<<29)
#define TRANS_DP_CTL_A 0xe0300
#define TRANS_DP_CTL_B 0xe1300
#define TRANS_DP_CTL_C 0xe2300
#define TRANS_DP_CTL(pipe) (TRANS_DP_CTL_A + (pipe) * 0x01000)
#define TRANS_DP_OUTPUT_ENABLE (1<<31)
#define TRANS_DP_PORT_SEL_B (0<<29)
#define TRANS_DP_PORT_SEL_C (1<<29)
#define TRANS_DP_PORT_SEL_D (2<<29)
#define TRANS_DP_PORT_SEL_MASK (3<<29)
#define TRANS_DP_AUDIO_ONLY (1<<26)
#define TRANS_DP_ENH_FRAMING (1<<18)
#define TRANS_DP_8BPC (0<<9)
#define TRANS_DP_10BPC (1<<9)
#define TRANS_DP_6BPC (2<<9)
#define TRANS_DP_12BPC (3<<9)
#define TRANS_DP_VSYNC_ACTIVE_HIGH (1<<4)
#define TRANS_DP_VSYNC_ACTIVE_LOW 0
#define TRANS_DP_HSYNC_ACTIVE_HIGH (1<<3)
#define TRANS_DP_HSYNC_ACTIVE_LOW 0
#define TRANS_DP_SYNC_MASK (3<<3)
/* SNB eDP training params */
/* SNB A-stepping */
#define EDP_LINK_TRAIN_400MV_0DB_SNB_A (0x38<<22)
#define EDP_LINK_TRAIN_400MV_6DB_SNB_A (0x02<<22)
#define EDP_LINK_TRAIN_600MV_3_5DB_SNB_A (0x01<<22)
#define EDP_LINK_TRAIN_800MV_0DB_SNB_A (0x0<<22)
/* SNB B-stepping */
#define EDP_LINK_TRAIN_400MV_0DB_SNB_B (0x0<<22)
#define EDP_LINK_TRAIN_400MV_6DB_SNB_B (0x3a<<22)
#define EDP_LINK_TRAIN_600MV_3_5DB_SNB_B (0x39<<22)
#define EDP_LINK_TRAIN_800MV_0DB_SNB_B (0x38<<22)
#define EDP_LINK_TRAIN_VOL_EMP_MASK_SNB (0x3f<<22)
#endif /* _I915_REG_H_ */