iwlwifi: move iwl_cfg from iwl_priv to iwl_shared
Move the configuration pointer from the upper level iwl_priv to the
lower level iwl_shared structure, with associated code fixes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
diff --git a/drivers/net/wireless/iwlwifi/iwl-shared.h b/drivers/net/wireless/iwlwifi/iwl-shared.h
index 29a7284..df6d212 100644
--- a/drivers/net/wireless/iwlwifi/iwl-shared.h
+++ b/drivers/net/wireless/iwlwifi/iwl-shared.h
@@ -94,7 +94,6 @@
* This implementation is iwl-pci.c
*/
-struct iwl_cfg;
struct iwl_bus;
struct iwl_priv;
struct iwl_trans;
@@ -304,6 +303,101 @@
};
/**
+ * enum iwl_pa_type - Power Amplifier type
+ * @IWL_PA_SYSTEM: based on uCode configuration
+ * @IWL_PA_INTERNAL: use Internal only
+ */
+enum iwl_pa_type {
+ IWL_PA_SYSTEM = 0,
+ IWL_PA_INTERNAL = 1,
+};
+
+/*
+ * LED mode
+ * IWL_LED_DEFAULT: use device default
+ * IWL_LED_RF_STATE: turn LED on/off based on RF state
+ * LED ON = RF ON
+ * LED OFF = RF OFF
+ * IWL_LED_BLINK: adjust led blink rate based on blink table
+ */
+enum iwl_led_mode {
+ IWL_LED_DEFAULT,
+ IWL_LED_RF_STATE,
+ IWL_LED_BLINK,
+};
+
+/**
+ * struct iwl_cfg
+ * @name: Offical name of the device
+ * @fw_name_pre: Firmware filename prefix. The api version and extension
+ * (.ucode) will be added to filename before loading from disk. The
+ * filename is constructed as fw_name_pre<api>.ucode.
+ * @ucode_api_max: Highest version of uCode API supported by driver.
+ * @ucode_api_ok: oldest version of the uCode API that is OK to load
+ * without a warning, for use in transitions
+ * @ucode_api_min: Lowest version of uCode API supported by driver.
+ * @valid_tx_ant: valid transmit antenna
+ * @valid_rx_ant: valid receive antenna
+ * @sku: sku information from EEPROM
+ * @eeprom_ver: EEPROM version
+ * @eeprom_calib_ver: EEPROM calibration version
+ * @lib: pointer to the lib ops
+ * @additional_nic_config: additional nic configuration
+ * @base_params: pointer to basic parameters
+ * @ht_params: point to ht patameters
+ * @bt_params: pointer to bt parameters
+ * @pa_type: used by 6000 series only to identify the type of Power Amplifier
+ * @need_temp_offset_calib: need to perform temperature offset calibration
+ * @no_xtal_calib: some devices do not need crystal calibration data,
+ * don't send it to those
+ * @scan_rx_antennas: available antenna for scan operation
+ * @led_mode: 0=blinking, 1=On(RF On)/Off(RF Off)
+ * @adv_pm: advance power management
+ * @rx_with_siso_diversity: 1x1 device with rx antenna diversity
+ * @internal_wimax_coex: internal wifi/wimax combo device
+ * @iq_invert: I/Q inversion
+ * @temp_offset_v2: support v2 of temperature offset calibration
+ *
+ * We enable the driver to be backward compatible wrt API version. The
+ * driver specifies which APIs it supports (with @ucode_api_max being the
+ * highest and @ucode_api_min the lowest). Firmware will only be loaded if
+ * it has a supported API version.
+ *
+ * The ideal usage of this infrastructure is to treat a new ucode API
+ * release as a new hardware revision.
+ */
+struct iwl_cfg {
+ /* params specific to an individual device within a device family */
+ const char *name;
+ const char *fw_name_pre;
+ const unsigned int ucode_api_max;
+ const unsigned int ucode_api_ok;
+ const unsigned int ucode_api_min;
+ u8 valid_tx_ant;
+ u8 valid_rx_ant;
+ u16 sku;
+ u16 eeprom_ver;
+ u16 eeprom_calib_ver;
+ const struct iwl_lib_ops *lib;
+ void (*additional_nic_config)(struct iwl_priv *priv);
+ /* params not likely to change within a device family */
+ struct iwl_base_params *base_params;
+ /* params likely to change within a device family */
+ struct iwl_ht_params *ht_params;
+ struct iwl_bt_params *bt_params;
+ enum iwl_pa_type pa_type; /* if used set to IWL_PA_SYSTEM */
+ const bool need_temp_offset_calib; /* if used set to true */
+ const bool no_xtal_calib;
+ u8 scan_rx_antennas[IEEE80211_NUM_BANDS];
+ enum iwl_led_mode led_mode;
+ const bool adv_pm;
+ const bool rx_with_siso_diversity;
+ const bool internal_wimax_coex;
+ const bool iq_invert;
+ const bool temp_offset_v2;
+};
+
+/**
* struct iwl_shared - shared fields for all the layers of the driver
*
* @dbg_level_dev: dbg level set per device. Prevails on
@@ -313,6 +407,7 @@
* @status: STATUS_*
* @valid_contexts: microcode/device supports multiple contexts
* @bus: pointer to the bus layer data
+ * @cfg: see struct iwl_cfg
* @priv: pointer to the upper layer data
* @hw_params: see struct iwl_hw_params
* @workqueue: the workqueue used by all the layers of the driver
@@ -320,6 +415,7 @@
* @sta_lock: protects the station table.
* If lock and sta_lock are needed, lock must be acquired first.
* @mutex:
+ * @eeprom: pointer to the eeprom/OTP image
* @ucode_type: indicator of loaded ucode image
* @notif_waits: things waiting for notification
* @notif_wait_lock: lock protecting notification
@@ -340,6 +436,7 @@
u8 valid_contexts;
struct iwl_bus *bus;
+ struct iwl_cfg *cfg;
struct iwl_priv *priv;
struct iwl_trans *trans;
struct iwl_hw_params hw_params;
@@ -373,6 +470,7 @@
/*Whatever _m is (iwl_trans, iwl_priv, iwl_bus, these macros will work */
#define priv(_m) ((_m)->shrd->priv)
+#define cfg(_m) ((_m)->shrd->cfg)
#define bus(_m) ((_m)->shrd->bus)
#define trans(_m) ((_m)->shrd->trans)
#define hw_params(_m) ((_m)->shrd->hw_params)