can: CAN Network device driver and Netlink interface

The CAN network device driver interface provides a generic interface to
setup, configure and monitor CAN network devices. It exports a set of
common data structures and functions, which all real CAN network device
drivers should use. Please have a look to the SJA1000 or MSCAN driver
to understand how to use them. The name of the module is can-dev.ko.

Furthermore, it adds a Netlink interface allowing to configure the CAN
device using the program "ip" from the iproute2 utility suite.

For further information please check "Documentation/networking/can.txt"

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/include/linux/can/netlink.h b/include/linux/can/netlink.h
new file mode 100644
index 0000000..9ecbb78
--- /dev/null
+++ b/include/linux/can/netlink.h
@@ -0,0 +1,113 @@
+/*
+ * linux/can/netlink.h
+ *
+ * Definitions for the CAN netlink interface
+ *
+ * Copyright (c) 2009 Wolfgang Grandegger <wg@grandegger.com>
+ *
+ * Send feedback to <socketcan-users@lists.berlios.de>
+ *
+ */
+
+#ifndef CAN_NETLINK_H
+#define CAN_NETLINK_H
+
+#include <linux/types.h>
+
+/*
+ * CAN bit-timing parameters
+ *
+ * For futher information, please read chapter "8 BIT TIMING
+ * REQUIREMENTS" of the "Bosch CAN Specification version 2.0"
+ * at http://www.semiconductors.bosch.de/pdf/can2spec.pdf.
+ */
+struct can_bittiming {
+	__u32 bitrate;		/* Bit-rate in bits/second */
+	__u32 sample_point;	/* Sample point in one-tenth of a percent */
+	__u32 tq;		/* Time quanta (TQ) in nanoseconds */
+	__u32 prop_seg;		/* Propagation segment in TQs */
+	__u32 phase_seg1;	/* Phase buffer segment 1 in TQs */
+	__u32 phase_seg2;	/* Phase buffer segment 2 in TQs */
+	__u32 sjw;		/* Synchronisation jump width in TQs */
+	__u32 brp;		/* Bit-rate prescaler */
+};
+
+/*
+ * CAN harware-dependent bit-timing constant
+ *
+ * Used for calculating and checking bit-timing parameters
+ */
+struct can_bittiming_const {
+	char name[16];		/* Name of the CAN controller hardware */
+	__u32 tseg1_min;	/* Time segement 1 = prop_seg + phase_seg1 */
+	__u32 tseg1_max;
+	__u32 tseg2_min;	/* Time segement 2 = phase_seg2 */
+	__u32 tseg2_max;
+	__u32 sjw_max;		/* Synchronisation jump width */
+	__u32 brp_min;		/* Bit-rate prescaler */
+	__u32 brp_max;
+	__u32 brp_inc;
+};
+
+/*
+ * CAN clock parameters
+ */
+struct can_clock {
+	__u32 freq;		/* CAN system clock frequency in Hz */
+};
+
+/*
+ * CAN operational and error states
+ */
+enum can_state {
+	CAN_STATE_ERROR_ACTIVE = 0,	/* RX/TX error count < 96 */
+	CAN_STATE_ERROR_WARNING,	/* RX/TX error count < 128 */
+	CAN_STATE_ERROR_PASSIVE,	/* RX/TX error count < 256 */
+	CAN_STATE_BUS_OFF,		/* RX/TX error count >= 256 */
+	CAN_STATE_STOPPED,		/* Device is stopped */
+	CAN_STATE_SLEEPING,		/* Device is sleeping */
+	CAN_STATE_MAX
+};
+
+/*
+ * CAN controller mode
+ */
+struct can_ctrlmode {
+	__u32 mask;
+	__u32 flags;
+};
+
+#define CAN_CTRLMODE_LOOPBACK	0x1	/* Loopback mode */
+#define CAN_CTRLMODE_LISTENONLY	0x2 	/* Listen-only mode */
+#define CAN_CTRLMODE_3_SAMPLES	0x4	/* Triple sampling mode */
+
+/*
+ * CAN device statistics
+ */
+struct can_device_stats {
+	__u32 bus_error;	/* Bus errors */
+	__u32 error_warning;	/* Changes to error warning state */
+	__u32 error_passive;	/* Changes to error passive state */
+	__u32 bus_off;		/* Changes to bus off state */
+	__u32 arbitration_lost; /* Arbitration lost errors */
+	__u32 restarts;		/* CAN controller re-starts */
+};
+
+/*
+ * CAN netlink interface
+ */
+enum {
+	IFLA_CAN_UNSPEC,
+	IFLA_CAN_BITTIMING,
+	IFLA_CAN_BITTIMING_CONST,
+	IFLA_CAN_CLOCK,
+	IFLA_CAN_STATE,
+	IFLA_CAN_CTRLMODE,
+	IFLA_CAN_RESTART_MS,
+	IFLA_CAN_RESTART,
+	__IFLA_CAN_MAX
+};
+
+#define IFLA_CAN_MAX	(__IFLA_CAN_MAX - 1)
+
+#endif /* CAN_NETLINK_H */