rt2800pci: add rt2800_mcu_request() wrapper
Part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/rt2x00/rt2800pci.c b/drivers/net/wireless/rt2x00/rt2800pci.c
index 83fe1ba..8f8f8d8 100644
--- a/drivers/net/wireless/rt2x00/rt2800pci.c
+++ b/drivers/net/wireless/rt2x00/rt2800pci.c
@@ -279,6 +279,13 @@
mutex_unlock(&rt2x00dev->csr_mutex);
}
+static inline void rt2800_mcu_request(struct rt2x00_dev *rt2x00dev,
+ const u8 command, const u8 token,
+ const u8 arg0, const u8 arg1)
+{
+ rt2800pci_mcu_request(rt2x00dev, command, token, arg0, arg1);
+}
+
static void rt2800pci_mcu_status(struct rt2x00_dev *rt2x00dev, const u8 token)
{
unsigned int i;
@@ -470,10 +477,10 @@
EEPROM_FREQ_LED_MODE);
if (led->type == LED_TYPE_RADIO) {
- rt2800pci_mcu_request(led->rt2x00dev, MCU_LED, 0xff, ledmode,
+ rt2800_mcu_request(led->rt2x00dev, MCU_LED, 0xff, ledmode,
enabled ? 0x20 : 0);
} else if (led->type == LED_TYPE_ASSOC) {
- rt2800pci_mcu_request(led->rt2x00dev, MCU_LED, 0xff, ledmode,
+ rt2800_mcu_request(led->rt2x00dev, MCU_LED, 0xff, ledmode,
enabled ? (bg_mode ? 0x60 : 0xa0) : 0x20);
} else if (led->type == LED_TYPE_QUALITY) {
/*
@@ -484,7 +491,7 @@
* work with bitshifting:
* (1 << level) - 1
*/
- rt2800pci_mcu_request(led->rt2x00dev, MCU_LED_STRENGTH, 0xff,
+ rt2800_mcu_request(led->rt2x00dev, MCU_LED_STRENGTH, 0xff,
(1 << brightness / (LED_FULL / 6)) - 1,
polarity);
}
@@ -2040,7 +2047,7 @@
/*
* Send signal to firmware during boot time.
*/
- rt2800pci_mcu_request(rt2x00dev, MCU_BOOT_SIGNAL, 0xff, 0, 0);
+ rt2800_mcu_request(rt2x00dev, MCU_BOOT_SIGNAL, 0xff, 0, 0);
/*
* Enable RX.
@@ -2066,15 +2073,15 @@
* Initialize LED control
*/
rt2x00_eeprom_read(rt2x00dev, EEPROM_LED1, &word);
- rt2800pci_mcu_request(rt2x00dev, MCU_LED_1, 0xff,
+ rt2800_mcu_request(rt2x00dev, MCU_LED_1, 0xff,
word & 0xff, (word >> 8) & 0xff);
rt2x00_eeprom_read(rt2x00dev, EEPROM_LED2, &word);
- rt2800pci_mcu_request(rt2x00dev, MCU_LED_2, 0xff,
+ rt2800_mcu_request(rt2x00dev, MCU_LED_2, 0xff,
word & 0xff, (word >> 8) & 0xff);
rt2x00_eeprom_read(rt2x00dev, EEPROM_LED3, &word);
- rt2800pci_mcu_request(rt2x00dev, MCU_LED_3, 0xff,
+ rt2800_mcu_request(rt2x00dev, MCU_LED_3, 0xff,
word & 0xff, (word >> 8) & 0xff);
return 0;
@@ -2123,10 +2130,10 @@
* if the device is booting and wasn't asleep it will return
* failure when attempting to wakeup.
*/
- rt2800pci_mcu_request(rt2x00dev, MCU_SLEEP, 0xff, 0, 2);
+ rt2800_mcu_request(rt2x00dev, MCU_SLEEP, 0xff, 0, 2);
if (state == STATE_AWAKE) {
- rt2800pci_mcu_request(rt2x00dev, MCU_WAKEUP, TOKEN_WAKUP, 0, 0);
+ rt2800_mcu_request(rt2x00dev, MCU_WAKEUP, TOKEN_WAKUP, 0, 0);
rt2800pci_mcu_status(rt2x00dev, TOKEN_WAKUP);
}