OMAP3: Add support for DPLL3 divisor values higher than 2
Previously only 1 and 2 was supported. This is needed for DVFS VDD2 control.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c
index cf41ab5..045da92 100644
--- a/arch/arm/mach-omap2/clock34xx.c
+++ b/arch/arm/mach-omap2/clock34xx.c
@@ -739,9 +739,9 @@
sdrcrate = sdrc_ick.rate;
if (rate > clk->rate)
- sdrcrate <<= ((rate / clk->rate) - 1);
+ sdrcrate <<= ((rate / clk->rate) >> 1);
else
- sdrcrate >>= ((clk->rate / rate) - 1);
+ sdrcrate >>= ((clk->rate / rate) >> 1);
sp = omap2_sdrc_get_params(sdrcrate);
if (!sp)
@@ -768,12 +768,9 @@
pr_debug("clock: SDRC timing params used: %08x %08x %08x\n",
sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb);
- /* REVISIT: SRAM code doesn't support other M2 divisors yet */
- WARN_ON(new_div != 1 && new_div != 2);
-
omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla,
sp->actim_ctrlb, new_div, unlock_dll, c,
- sp->mr);
+ sp->mr, rate > clk->rate);
return 0;
}
diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S
index 16eb4ef..487fa86 100644
--- a/arch/arm/mach-omap2/sram34xx.S
+++ b/arch/arm/mach-omap2/sram34xx.S
@@ -70,6 +70,7 @@
* r5 = number of MPU cycles to wait for SDRC to stabilize after
* reprogramming the SDRC when switching to a slower MPU speed
* r6 = new SDRC_MR_0 register value
+ * r7 = increasing SDRC rate? (1 = yes, 0 = no)
*
*/
ENTRY(omap3_sram_configure_core_dpll)
@@ -77,9 +78,10 @@
ldr r4, [sp, #52] @ pull extra args off the stack
ldr r5, [sp, #56] @ load extra args from the stack
ldr r6, [sp, #60] @ load extra args from the stack
+ ldr r7, [sp, #64] @ load extra args from the stack
dsb @ flush buffered writes to interconnect
- cmp r3, #0x2 @ if increasing SDRC clk rate,
- blne configure_sdrc @ program the SDRC regs early (for RFR)
+ cmp r7, #1 @ if increasing SDRC clk rate,
+ bleq configure_sdrc @ program the SDRC regs early (for RFR)
cmp r4, #SDRC_UNLOCK_DLL @ set the intended DLL state
bleq unlock_dll
blne lock_dll
@@ -89,7 +91,7 @@
cmp r4, #SDRC_UNLOCK_DLL @ wait for DLL status to change
bleq wait_dll_unlock
blne wait_dll_lock
- cmp r3, #0x1 @ if increasing SDRC clk rate,
+ cmp r7, #1 @ if increasing SDRC clk rate,
beq return_to_sdram @ return to SDRAM code, otherwise,
bl configure_sdrc @ reprogram SDRC regs now
mov r12, r5