| /* Copyright (c) 2012-2013, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/firmware.h> |
| #include <linux/slab.h> |
| #include <linux/platform_device.h> |
| #include <linux/device.h> |
| #include <linux/printk.h> |
| #include <linux/ratelimit.h> |
| #include <linux/debugfs.h> |
| #include <linux/list.h> |
| #include <linux/mfd/wcd9xxx/core.h> |
| #include <linux/mfd/wcd9xxx/core-resource.h> |
| #include <linux/mfd/wcd9xxx/wcd9xxx_registers.h> |
| #include <linux/mfd/wcd9xxx/wcd9320_registers.h> |
| #include <linux/mfd/wcd9xxx/pdata.h> |
| #include <sound/pcm.h> |
| #include <sound/pcm_params.h> |
| #include <sound/soc.h> |
| #include <sound/soc-dapm.h> |
| #include <sound/tlv.h> |
| #include <linux/bitops.h> |
| #include <linux/delay.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/kernel.h> |
| #include <linux/gpio.h> |
| #include <linux/input.h> |
| #include "wcd9320.h" |
| #include "wcd9306.h" |
| #include "wcd9xxx-mbhc.h" |
| #include "wcd9xxx-resmgr.h" |
| #include "wcd9xxx-common.h" |
| |
| #define WCD9XXX_JACK_MASK (SND_JACK_HEADSET | SND_JACK_OC_HPHL | \ |
| SND_JACK_OC_HPHR | SND_JACK_LINEOUT | \ |
| SND_JACK_UNSUPPORTED) |
| #define WCD9XXX_JACK_BUTTON_MASK (SND_JACK_BTN_0 | SND_JACK_BTN_1 | \ |
| SND_JACK_BTN_2 | SND_JACK_BTN_3 | \ |
| SND_JACK_BTN_4 | SND_JACK_BTN_5 | \ |
| SND_JACK_BTN_6 | SND_JACK_BTN_7) |
| |
| #define NUM_DCE_PLUG_DETECT 3 |
| #define NUM_DCE_PLUG_INS_DETECT 5 |
| #define NUM_ATTEMPTS_INSERT_DETECT 25 |
| #define NUM_ATTEMPTS_TO_REPORT 5 |
| |
| #define FAKE_INS_LOW 10 |
| #define FAKE_INS_HIGH 80 |
| #define FAKE_INS_HIGH_NO_SWCH 150 |
| #define FAKE_REMOVAL_MIN_PERIOD_MS 50 |
| #define FAKE_INS_DELTA_SCALED_MV 300 |
| |
| #define BUTTON_MIN 0x8000 |
| #define STATUS_REL_DETECTION 0x0C |
| |
| #define HS_DETECT_PLUG_TIME_MS (5 * 1000) |
| #define HS_DETECT_PLUG_INERVAL_MS 100 |
| #define SWCH_REL_DEBOUNCE_TIME_MS 50 |
| #define SWCH_IRQ_DEBOUNCE_TIME_US 5000 |
| #define BTN_RELEASE_DEBOUNCE_TIME_MS 25 |
| |
| #define GND_MIC_SWAP_THRESHOLD 2 |
| #define OCP_ATTEMPT 1 |
| |
| #define FW_READ_ATTEMPTS 15 |
| #define FW_READ_TIMEOUT 2000000 |
| |
| #define BUTTON_POLLING_SUPPORTED true |
| |
| #define MCLK_RATE_12288KHZ 12288000 |
| #define MCLK_RATE_9600KHZ 9600000 |
| |
| #define DEFAULT_DCE_STA_WAIT 55 |
| #define DEFAULT_DCE_WAIT 60000 |
| #define DEFAULT_STA_WAIT 5000 |
| |
| #define VDDIO_MICBIAS_MV 1800 |
| |
| #define WCD9XXX_MICBIAS_PULLDOWN_SETTLE_US 5000 |
| |
| #define WCD9XXX_HPHL_STATUS_READY_WAIT_US 1000 |
| #define WCD9XXX_MUX_SWITCH_READY_WAIT_MS 50 |
| #define WCD9XXX_MEAS_DELTA_MAX_MV 50 |
| #define WCD9XXX_MEAS_INVALD_RANGE_LOW_MV 20 |
| #define WCD9XXX_MEAS_INVALD_RANGE_HIGH_MV 80 |
| |
| /* |
| * Invalid voltage range for the detection |
| * of plug type with current source |
| */ |
| #define WCD9XXX_CS_MEAS_INVALD_RANGE_LOW_MV 110 |
| #define WCD9XXX_CS_MEAS_INVALD_RANGE_HIGH_MV 265 |
| |
| /* |
| * Threshold used to detect euro headset |
| * with current source |
| */ |
| #define WCD9XXX_CS_GM_SWAP_THRES_MIN_MV 10 |
| #define WCD9XXX_CS_GM_SWAP_THRES_MAX_MV 40 |
| |
| #define WCD9XXX_MBHC_NSC_CS 9 |
| #define WCD9XXX_GM_SWAP_THRES_MIN_MV 150 |
| #define WCD9XXX_GM_SWAP_THRES_MAX_MV 650 |
| #define WCD9XXX_THRESHOLD_MIC_THRESHOLD 200 |
| |
| #define WCD9XXX_USLEEP_RANGE_MARGIN_US 100 |
| |
| /* RX_HPH_CNP_WG_TIME increases by 0.24ms */ |
| #define WCD9XXX_WG_TIME_FACTOR_US 240 |
| |
| #define WCD9XXX_IRQ_MBHC_JACK_SWITCH_DEFAULT 28 |
| |
| #define WCD9XXX_V_CS_HS_MAX 500 |
| #define WCD9XXX_V_CS_NO_MIC 5 |
| #define WCD9XXX_MB_MEAS_DELTA_MAX_MV 80 |
| #define WCD9XXX_CS_MEAS_DELTA_MAX_MV 10 |
| |
| static int impedance_detect_en; |
| module_param(impedance_detect_en, int, |
| S_IRUGO | S_IWUSR | S_IWGRP); |
| MODULE_PARM_DESC(impedance_detect_en, "enable/disable impedance detect"); |
| |
| static bool detect_use_vddio_switch = true; |
| |
| struct wcd9xxx_mbhc_detect { |
| u16 dce; |
| u16 sta; |
| u16 hphl_status; |
| bool swap_gnd; |
| bool vddio; |
| bool hwvalue; |
| bool mic_bias; |
| /* internal purpose from here */ |
| bool _above_no_mic; |
| bool _below_v_hs_max; |
| s16 _vdces; |
| enum wcd9xxx_mbhc_plug_type _type; |
| }; |
| |
| enum meas_type { |
| STA = 0, |
| DCE, |
| }; |
| |
| enum { |
| MBHC_USE_HPHL_TRIGGER = 1, |
| MBHC_USE_MB_TRIGGER = 2 |
| }; |
| |
| /* |
| * Flags to track of PA and DAC state. |
| * PA and DAC should be tracked separately as AUXPGA loopback requires |
| * only PA to be turned on without DAC being on. |
| */ |
| enum pa_dac_ack_flags { |
| WCD9XXX_HPHL_PA_OFF_ACK = 0, |
| WCD9XXX_HPHR_PA_OFF_ACK, |
| WCD9XXX_HPHL_DAC_OFF_ACK, |
| WCD9XXX_HPHR_DAC_OFF_ACK |
| }; |
| |
| enum wcd9xxx_current_v_idx { |
| WCD9XXX_CURRENT_V_INS_H, |
| WCD9XXX_CURRENT_V_INS_HU, |
| WCD9XXX_CURRENT_V_B1_H, |
| WCD9XXX_CURRENT_V_B1_HU, |
| WCD9XXX_CURRENT_V_BR_H, |
| }; |
| |
| static int wcd9xxx_detect_impedance(struct wcd9xxx_mbhc *mbhc, uint32_t *zl, |
| uint32_t *zr); |
| static s16 wcd9xxx_get_current_v(struct wcd9xxx_mbhc *mbhc, |
| const enum wcd9xxx_current_v_idx idx); |
| static void wcd9xxx_get_z(struct wcd9xxx_mbhc *mbhc, s16 *dce_z, s16 *sta_z); |
| static void wcd9xxx_mbhc_calc_thres(struct wcd9xxx_mbhc *mbhc); |
| |
| static bool wcd9xxx_mbhc_polling(struct wcd9xxx_mbhc *mbhc) |
| { |
| return mbhc->polling_active; |
| } |
| |
| static void wcd9xxx_turn_onoff_override(struct wcd9xxx_mbhc *mbhc, bool on) |
| { |
| struct snd_soc_codec *codec = mbhc->codec; |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, |
| 0x04, on ? 0x04 : 0x00); |
| } |
| |
| /* called under codec_resource_lock acquisition */ |
| static void wcd9xxx_pause_hs_polling(struct wcd9xxx_mbhc *mbhc) |
| { |
| struct snd_soc_codec *codec = mbhc->codec; |
| |
| pr_debug("%s: enter\n", __func__); |
| if (!mbhc->polling_active) { |
| pr_debug("polling not active, nothing to pause\n"); |
| return; |
| } |
| |
| /* Soft reset MBHC block */ |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x8, 0x8); |
| pr_debug("%s: leave\n", __func__); |
| } |
| |
| /* called under codec_resource_lock acquisition */ |
| static void wcd9xxx_start_hs_polling(struct wcd9xxx_mbhc *mbhc) |
| { |
| s16 v_brh, v_b1_hu; |
| struct snd_soc_codec *codec = mbhc->codec; |
| int mbhc_state = mbhc->mbhc_state; |
| |
| pr_debug("%s: enter\n", __func__); |
| if (!mbhc->polling_active) { |
| pr_debug("Polling is not active, do not start polling\n"); |
| return; |
| } |
| snd_soc_write(codec, WCD9XXX_A_MBHC_SCALING_MUX_1, 0x04); |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mux_bias_block) |
| mbhc->mbhc_cb->enable_mux_bias_block(codec); |
| else |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_SCALING_MUX_1, |
| 0x80, 0x80); |
| |
| if (!mbhc->no_mic_headset_override && |
| mbhc_state == MBHC_STATE_POTENTIAL) { |
| pr_debug("%s recovering MBHC state machine\n", __func__); |
| mbhc->mbhc_state = MBHC_STATE_POTENTIAL_RECOVERY; |
| /* set to max button press threshold */ |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B2_CTL, 0x7F); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B1_CTL, 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B4_CTL, 0x7F); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B3_CTL, 0xFF); |
| /* set to max */ |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B6_CTL, 0x7F); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B5_CTL, 0xFF); |
| |
| v_brh = wcd9xxx_get_current_v(mbhc, WCD9XXX_CURRENT_V_BR_H); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B10_CTL, |
| (v_brh >> 8) & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B9_CTL, |
| v_brh & 0xFF); |
| v_b1_hu = wcd9xxx_get_current_v(mbhc, WCD9XXX_CURRENT_V_B1_HU); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B3_CTL, |
| v_b1_hu & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B4_CTL, |
| (v_b1_hu >> 8) & 0xFF); |
| } |
| |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_EN_CTL, 0x1); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x8, 0x0); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_EN_CTL, 0x1); |
| pr_debug("%s: leave\n", __func__); |
| } |
| |
| static int __wcd9xxx_resmgr_get_k_val(struct wcd9xxx_mbhc *mbhc, |
| unsigned int cfilt_mv) |
| { |
| if (mbhc->mbhc_cb && |
| mbhc->mbhc_cb->get_cdc_type() == |
| WCD9XXX_CDC_TYPE_HELICON) |
| return 0x18; |
| |
| return wcd9xxx_resmgr_get_k_val(mbhc->resmgr, cfilt_mv); |
| } |
| |
| /* |
| * called under codec_resource_lock acquisition |
| * return old status |
| */ |
| static bool __wcd9xxx_switch_micbias(struct wcd9xxx_mbhc *mbhc, |
| int vddio_switch, bool restartpolling, |
| bool checkpolling) |
| { |
| bool ret; |
| int cfilt_k_val; |
| bool override; |
| struct snd_soc_codec *codec; |
| struct mbhc_internal_cal_data *d = &mbhc->mbhc_data; |
| |
| codec = mbhc->codec; |
| |
| if (mbhc->micbias_enable) { |
| pr_debug("%s: micbias is already on\n", __func__); |
| ret = mbhc->mbhc_micbias_switched; |
| return ret; |
| } |
| |
| ret = mbhc->mbhc_micbias_switched; |
| if (vddio_switch && !mbhc->mbhc_micbias_switched && |
| (!checkpolling || mbhc->polling_active)) { |
| if (restartpolling) |
| wcd9xxx_pause_hs_polling(mbhc); |
| override = snd_soc_read(codec, WCD9XXX_A_CDC_MBHC_B1_CTL) & |
| 0x04; |
| if (!override) |
| wcd9xxx_turn_onoff_override(mbhc, true); |
| /* Adjust threshold if Mic Bias voltage changes */ |
| if (d->micb_mv != VDDIO_MICBIAS_MV) { |
| cfilt_k_val = __wcd9xxx_resmgr_get_k_val(mbhc, |
| VDDIO_MICBIAS_MV); |
| usleep_range(10000, 10000); |
| snd_soc_update_bits(codec, |
| mbhc->mbhc_bias_regs.cfilt_val, |
| 0xFC, (cfilt_k_val << 2)); |
| usleep_range(10000, 10000); |
| /* Threshods for insertion/removal */ |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B1_CTL, |
| d->v_ins_hu[MBHC_V_IDX_VDDIO] & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B2_CTL, |
| (d->v_ins_hu[MBHC_V_IDX_VDDIO] >> 8) & |
| 0xFF); |
| /* Threshods for button press */ |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B3_CTL, |
| d->v_b1_hu[MBHC_V_IDX_VDDIO] & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B4_CTL, |
| (d->v_b1_hu[MBHC_V_IDX_VDDIO] >> 8) & |
| 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B5_CTL, |
| d->v_b1_h[MBHC_V_IDX_VDDIO] & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B6_CTL, |
| (d->v_b1_h[MBHC_V_IDX_VDDIO] >> 8) & |
| 0xFF); |
| /* Threshods for button release */ |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B9_CTL, |
| d->v_brh[MBHC_V_IDX_VDDIO] & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B10_CTL, |
| (d->v_brh[MBHC_V_IDX_VDDIO] >> 8) & 0xFF); |
| pr_debug("%s: Programmed MBHC thresholds to VDDIO\n", |
| __func__); |
| } |
| |
| /* Enable MIC BIAS Switch to VDDIO */ |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.mbhc_reg, |
| 0x80, 0x80); |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.mbhc_reg, |
| 0x10, 0x00); |
| if (!override) |
| wcd9xxx_turn_onoff_override(mbhc, false); |
| if (restartpolling) |
| wcd9xxx_start_hs_polling(mbhc); |
| |
| mbhc->mbhc_micbias_switched = true; |
| pr_debug("%s: VDDIO switch enabled\n", __func__); |
| } else if (!vddio_switch && mbhc->mbhc_micbias_switched) { |
| if ((!checkpolling || mbhc->polling_active) && |
| restartpolling) |
| wcd9xxx_pause_hs_polling(mbhc); |
| /* Reprogram thresholds */ |
| if (d->micb_mv != VDDIO_MICBIAS_MV) { |
| cfilt_k_val = |
| __wcd9xxx_resmgr_get_k_val(mbhc, |
| d->micb_mv); |
| snd_soc_update_bits(codec, |
| mbhc->mbhc_bias_regs.cfilt_val, |
| 0xFC, (cfilt_k_val << 2)); |
| usleep_range(10000, 10000); |
| /* Revert threshods for insertion/removal */ |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B1_CTL, |
| d->v_ins_hu[MBHC_V_IDX_CFILT] & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B2_CTL, |
| (d->v_ins_hu[MBHC_V_IDX_CFILT] >> 8) & |
| 0xFF); |
| /* Revert threshods for button press */ |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B3_CTL, |
| d->v_b1_hu[MBHC_V_IDX_CFILT] & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B4_CTL, |
| (d->v_b1_hu[MBHC_V_IDX_CFILT] >> 8) & |
| 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B5_CTL, |
| d->v_b1_h[MBHC_V_IDX_CFILT] & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B6_CTL, |
| (d->v_b1_h[MBHC_V_IDX_CFILT] >> 8) & |
| 0xFF); |
| /* Revert threshods for button release */ |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B9_CTL, |
| d->v_brh[MBHC_V_IDX_CFILT] & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B10_CTL, |
| (d->v_brh[MBHC_V_IDX_CFILT] >> 8) & 0xFF); |
| pr_debug("%s: Programmed MBHC thresholds to MICBIAS\n", |
| __func__); |
| } |
| |
| /* Disable MIC BIAS Switch to VDDIO */ |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.mbhc_reg, 0x80, |
| 0x00); |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.mbhc_reg, 0x10, |
| 0x00); |
| |
| if ((!checkpolling || mbhc->polling_active) && restartpolling) |
| wcd9xxx_start_hs_polling(mbhc); |
| |
| mbhc->mbhc_micbias_switched = false; |
| pr_debug("%s: VDDIO switch disabled\n", __func__); |
| } |
| |
| return ret; |
| } |
| |
| static void wcd9xxx_switch_micbias(struct wcd9xxx_mbhc *mbhc, int vddio_switch) |
| { |
| __wcd9xxx_switch_micbias(mbhc, vddio_switch, true, true); |
| } |
| |
| static s16 wcd9xxx_get_current_v(struct wcd9xxx_mbhc *mbhc, |
| const enum wcd9xxx_current_v_idx idx) |
| { |
| enum mbhc_v_index vidx; |
| s16 ret = -EINVAL; |
| |
| if ((mbhc->mbhc_data.micb_mv != VDDIO_MICBIAS_MV) && |
| mbhc->mbhc_micbias_switched) |
| vidx = MBHC_V_IDX_VDDIO; |
| else |
| vidx = MBHC_V_IDX_CFILT; |
| |
| switch (idx) { |
| case WCD9XXX_CURRENT_V_INS_H: |
| ret = (s16)mbhc->mbhc_data.v_ins_h[vidx]; |
| break; |
| case WCD9XXX_CURRENT_V_INS_HU: |
| ret = (s16)mbhc->mbhc_data.v_ins_hu[vidx]; |
| break; |
| case WCD9XXX_CURRENT_V_B1_H: |
| ret = (s16)mbhc->mbhc_data.v_b1_h[vidx]; |
| break; |
| case WCD9XXX_CURRENT_V_B1_HU: |
| ret = (s16)mbhc->mbhc_data.v_b1_hu[vidx]; |
| break; |
| case WCD9XXX_CURRENT_V_BR_H: |
| ret = (s16)mbhc->mbhc_data.v_brh[vidx]; |
| break; |
| } |
| |
| return ret; |
| } |
| |
| void *wcd9xxx_mbhc_cal_btn_det_mp( |
| const struct wcd9xxx_mbhc_btn_detect_cfg *btn_det, |
| const enum wcd9xxx_mbhc_btn_det_mem mem) |
| { |
| void *ret = &btn_det->_v_btn_low; |
| |
| switch (mem) { |
| case MBHC_BTN_DET_GAIN: |
| ret += sizeof(btn_det->_n_cic); |
| case MBHC_BTN_DET_N_CIC: |
| ret += sizeof(btn_det->_n_ready); |
| case MBHC_BTN_DET_N_READY: |
| ret += sizeof(btn_det->_v_btn_high[0]) * btn_det->num_btn; |
| case MBHC_BTN_DET_V_BTN_HIGH: |
| ret += sizeof(btn_det->_v_btn_low[0]) * btn_det->num_btn; |
| case MBHC_BTN_DET_V_BTN_LOW: |
| /* do nothing */ |
| break; |
| default: |
| ret = NULL; |
| } |
| |
| return ret; |
| } |
| EXPORT_SYMBOL(wcd9xxx_mbhc_cal_btn_det_mp); |
| |
| static void wcd9xxx_calibrate_hs_polling(struct wcd9xxx_mbhc *mbhc) |
| { |
| struct snd_soc_codec *codec = mbhc->codec; |
| const s16 v_ins_hu = wcd9xxx_get_current_v(mbhc, |
| WCD9XXX_CURRENT_V_INS_HU); |
| const s16 v_b1_hu = wcd9xxx_get_current_v(mbhc, |
| WCD9XXX_CURRENT_V_B1_HU); |
| const s16 v_b1_h = wcd9xxx_get_current_v(mbhc, WCD9XXX_CURRENT_V_B1_H); |
| const s16 v_brh = wcd9xxx_get_current_v(mbhc, WCD9XXX_CURRENT_V_BR_H); |
| |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B1_CTL, v_ins_hu & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B2_CTL, |
| (v_ins_hu >> 8) & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B3_CTL, v_b1_hu & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B4_CTL, |
| (v_b1_hu >> 8) & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B5_CTL, v_b1_h & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B6_CTL, |
| (v_b1_h >> 8) & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B9_CTL, v_brh & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B10_CTL, |
| (v_brh >> 8) & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B11_CTL, |
| mbhc->mbhc_data.v_brl & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B12_CTL, |
| (mbhc->mbhc_data.v_brl >> 8) & 0xFF); |
| } |
| |
| static void wcd9xxx_codec_switch_cfilt_mode(struct wcd9xxx_mbhc *mbhc, |
| bool fast) |
| { |
| struct snd_soc_codec *codec = mbhc->codec; |
| struct wcd9xxx_cfilt_mode cfilt_mode; |
| |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->switch_cfilt_mode) { |
| cfilt_mode = mbhc->mbhc_cb->switch_cfilt_mode(mbhc, fast); |
| } else { |
| if (fast) |
| cfilt_mode.reg_mode_val = WCD9XXX_CFILT_FAST_MODE; |
| else |
| cfilt_mode.reg_mode_val = WCD9XXX_CFILT_SLOW_MODE; |
| |
| cfilt_mode.reg_mask = 0x40; |
| cfilt_mode.cur_mode_val = |
| snd_soc_read(codec, mbhc->mbhc_bias_regs.cfilt_ctl) & 0x40; |
| } |
| |
| if (cfilt_mode.cur_mode_val |
| != cfilt_mode.reg_mode_val) { |
| if (mbhc->polling_active) |
| wcd9xxx_pause_hs_polling(mbhc); |
| snd_soc_update_bits(codec, |
| mbhc->mbhc_bias_regs.cfilt_ctl, |
| cfilt_mode.reg_mask, |
| cfilt_mode.reg_mode_val); |
| if (mbhc->polling_active) |
| wcd9xxx_start_hs_polling(mbhc); |
| pr_debug("%s: CFILT mode change (%x to %x)\n", __func__, |
| cfilt_mode.cur_mode_val, |
| cfilt_mode.reg_mode_val); |
| } else { |
| pr_debug("%s: CFILT Value is already %x\n", |
| __func__, cfilt_mode.cur_mode_val); |
| } |
| } |
| |
| static void wcd9xxx_jack_report(struct wcd9xxx_mbhc *mbhc, |
| struct snd_soc_jack *jack, int status, int mask) |
| { |
| if (jack == &mbhc->headset_jack) { |
| wcd9xxx_resmgr_cond_update_cond(mbhc->resmgr, |
| WCD9XXX_COND_HPH_MIC, |
| status & SND_JACK_MICROPHONE); |
| wcd9xxx_resmgr_cond_update_cond(mbhc->resmgr, |
| WCD9XXX_COND_HPH, |
| status & SND_JACK_HEADPHONE); |
| } |
| |
| snd_soc_jack_report_no_dapm(jack, status, mask); |
| } |
| |
| static void __hphocp_off_report(struct wcd9xxx_mbhc *mbhc, u32 jack_status, |
| int irq) |
| { |
| struct snd_soc_codec *codec; |
| |
| pr_debug("%s: clear ocp status %x\n", __func__, jack_status); |
| codec = mbhc->codec; |
| if (mbhc->hph_status & jack_status) { |
| mbhc->hph_status &= ~jack_status; |
| wcd9xxx_jack_report(mbhc, &mbhc->headset_jack, |
| mbhc->hph_status, WCD9XXX_JACK_MASK); |
| snd_soc_update_bits(codec, WCD9XXX_A_RX_HPH_OCP_CTL, 0x10, |
| 0x00); |
| snd_soc_update_bits(codec, WCD9XXX_A_RX_HPH_OCP_CTL, 0x10, |
| 0x10); |
| /* |
| * reset retry counter as PA is turned off signifying |
| * start of new OCP detection session |
| */ |
| if (WCD9XXX_IRQ_HPH_PA_OCPL_FAULT) |
| mbhc->hphlocp_cnt = 0; |
| else |
| mbhc->hphrocp_cnt = 0; |
| wcd9xxx_enable_irq(mbhc->resmgr->core_res, irq); |
| } |
| } |
| |
| static void hphrocp_off_report(struct wcd9xxx_mbhc *mbhc, u32 jack_status) |
| { |
| __hphocp_off_report(mbhc, SND_JACK_OC_HPHR, |
| WCD9XXX_IRQ_HPH_PA_OCPR_FAULT); |
| } |
| |
| static void hphlocp_off_report(struct wcd9xxx_mbhc *mbhc, u32 jack_status) |
| { |
| __hphocp_off_report(mbhc, SND_JACK_OC_HPHL, |
| WCD9XXX_IRQ_HPH_PA_OCPL_FAULT); |
| } |
| |
| static void wcd9xxx_get_mbhc_micbias_regs(struct wcd9xxx_mbhc *mbhc, |
| struct mbhc_micbias_regs *micbias_regs) |
| { |
| unsigned int cfilt; |
| struct wcd9xxx_pdata *pdata = mbhc->resmgr->pdata; |
| |
| if (mbhc->mbhc_cb && |
| mbhc->mbhc_cb->get_cdc_type() == |
| WCD9XXX_CDC_TYPE_HELICON) { |
| micbias_regs->mbhc_reg = WCD9XXX_A_MICB_1_MBHC; |
| micbias_regs->int_rbias = WCD9XXX_A_MICB_1_INT_RBIAS; |
| micbias_regs->ctl_reg = WCD9XXX_A_MICB_1_CTL; |
| micbias_regs->cfilt_val = WCD9XXX_A_MICB_CFILT_1_VAL; |
| micbias_regs->cfilt_ctl = WCD9XXX_A_MICB_CFILT_1_CTL; |
| mbhc->mbhc_data.micb_mv = 1800; |
| return; |
| } |
| |
| switch (mbhc->mbhc_cfg->micbias) { |
| case MBHC_MICBIAS1: |
| cfilt = pdata->micbias.bias1_cfilt_sel; |
| micbias_regs->mbhc_reg = WCD9XXX_A_MICB_1_MBHC; |
| micbias_regs->int_rbias = WCD9XXX_A_MICB_1_INT_RBIAS; |
| micbias_regs->ctl_reg = WCD9XXX_A_MICB_1_CTL; |
| break; |
| case MBHC_MICBIAS2: |
| cfilt = pdata->micbias.bias2_cfilt_sel; |
| micbias_regs->mbhc_reg = WCD9XXX_A_MICB_2_MBHC; |
| micbias_regs->int_rbias = WCD9XXX_A_MICB_2_INT_RBIAS; |
| micbias_regs->ctl_reg = WCD9XXX_A_MICB_2_CTL; |
| break; |
| case MBHC_MICBIAS3: |
| cfilt = pdata->micbias.bias3_cfilt_sel; |
| micbias_regs->mbhc_reg = WCD9XXX_A_MICB_3_MBHC; |
| micbias_regs->int_rbias = WCD9XXX_A_MICB_3_INT_RBIAS; |
| micbias_regs->ctl_reg = WCD9XXX_A_MICB_3_CTL; |
| break; |
| case MBHC_MICBIAS4: |
| cfilt = pdata->micbias.bias4_cfilt_sel; |
| micbias_regs->mbhc_reg = mbhc->resmgr->reg_addr->micb_4_mbhc; |
| micbias_regs->int_rbias = |
| mbhc->resmgr->reg_addr->micb_4_int_rbias; |
| micbias_regs->ctl_reg = mbhc->resmgr->reg_addr->micb_4_ctl; |
| break; |
| default: |
| /* Should never reach here */ |
| pr_err("%s: Invalid MIC BIAS for MBHC\n", __func__); |
| return; |
| } |
| |
| micbias_regs->cfilt_sel = cfilt; |
| |
| switch (cfilt) { |
| case WCD9XXX_CFILT1_SEL: |
| micbias_regs->cfilt_val = WCD9XXX_A_MICB_CFILT_1_VAL; |
| micbias_regs->cfilt_ctl = WCD9XXX_A_MICB_CFILT_1_CTL; |
| mbhc->mbhc_data.micb_mv = |
| mbhc->resmgr->pdata->micbias.cfilt1_mv; |
| break; |
| case WCD9XXX_CFILT2_SEL: |
| micbias_regs->cfilt_val = WCD9XXX_A_MICB_CFILT_2_VAL; |
| micbias_regs->cfilt_ctl = WCD9XXX_A_MICB_CFILT_2_CTL; |
| mbhc->mbhc_data.micb_mv = |
| mbhc->resmgr->pdata->micbias.cfilt2_mv; |
| break; |
| case WCD9XXX_CFILT3_SEL: |
| micbias_regs->cfilt_val = WCD9XXX_A_MICB_CFILT_3_VAL; |
| micbias_regs->cfilt_ctl = WCD9XXX_A_MICB_CFILT_3_CTL; |
| mbhc->mbhc_data.micb_mv = |
| mbhc->resmgr->pdata->micbias.cfilt3_mv; |
| break; |
| } |
| } |
| |
| static void wcd9xxx_clr_and_turnon_hph_padac(struct wcd9xxx_mbhc *mbhc) |
| { |
| bool pa_turned_on = false; |
| struct snd_soc_codec *codec = mbhc->codec; |
| u8 wg_time; |
| |
| wg_time = snd_soc_read(codec, WCD9XXX_A_RX_HPH_CNP_WG_TIME) ; |
| wg_time += 1; |
| |
| if (test_and_clear_bit(WCD9XXX_HPHR_DAC_OFF_ACK, |
| &mbhc->hph_pa_dac_state)) { |
| pr_debug("%s: HPHR clear flag and enable DAC\n", __func__); |
| snd_soc_update_bits(codec, WCD9XXX_A_RX_HPH_R_DAC_CTL, |
| 0xC0, 0xC0); |
| } |
| if (test_and_clear_bit(WCD9XXX_HPHL_DAC_OFF_ACK, |
| &mbhc->hph_pa_dac_state)) { |
| pr_debug("%s: HPHL clear flag and enable DAC\n", __func__); |
| snd_soc_update_bits(codec, WCD9XXX_A_RX_HPH_L_DAC_CTL, |
| 0x80, 0x80); |
| } |
| |
| if (test_and_clear_bit(WCD9XXX_HPHR_PA_OFF_ACK, |
| &mbhc->hph_pa_dac_state)) { |
| pr_debug("%s: HPHR clear flag and enable PA\n", __func__); |
| snd_soc_update_bits(codec, WCD9XXX_A_RX_HPH_CNP_EN, 0x10, |
| 1 << 4); |
| pa_turned_on = true; |
| } |
| if (test_and_clear_bit(WCD9XXX_HPHL_PA_OFF_ACK, |
| &mbhc->hph_pa_dac_state)) { |
| pr_debug("%s: HPHL clear flag and enable PA\n", __func__); |
| snd_soc_update_bits(codec, WCD9XXX_A_RX_HPH_CNP_EN, 0x20, 1 |
| << 5); |
| pa_turned_on = true; |
| } |
| |
| if (pa_turned_on) { |
| pr_debug("%s: PA was turned off by MBHC and not by DAPM\n", |
| __func__); |
| usleep_range(wg_time * 1000, wg_time * 1000); |
| } |
| } |
| |
| static int wcd9xxx_cancel_btn_work(struct wcd9xxx_mbhc *mbhc) |
| { |
| int r; |
| r = cancel_delayed_work_sync(&mbhc->mbhc_btn_dwork); |
| if (r) |
| /* if scheduled mbhc.mbhc_btn_dwork is canceled from here, |
| * we have to unlock from here instead btn_work */ |
| wcd9xxx_unlock_sleep(mbhc->resmgr->core_res); |
| return r; |
| } |
| |
| static bool wcd9xxx_is_hph_dac_on(struct snd_soc_codec *codec, int left) |
| { |
| u8 hph_reg_val = 0; |
| if (left) |
| hph_reg_val = snd_soc_read(codec, WCD9XXX_A_RX_HPH_L_DAC_CTL); |
| else |
| hph_reg_val = snd_soc_read(codec, WCD9XXX_A_RX_HPH_R_DAC_CTL); |
| |
| return (hph_reg_val & 0xC0) ? true : false; |
| } |
| |
| static bool wcd9xxx_is_hph_pa_on(struct snd_soc_codec *codec) |
| { |
| u8 hph_reg_val = 0; |
| hph_reg_val = snd_soc_read(codec, WCD9XXX_A_RX_HPH_CNP_EN); |
| |
| return (hph_reg_val & 0x30) ? true : false; |
| } |
| |
| /* called under codec_resource_lock acquisition */ |
| static void wcd9xxx_set_and_turnoff_hph_padac(struct wcd9xxx_mbhc *mbhc) |
| { |
| u8 wg_time; |
| struct snd_soc_codec *codec = mbhc->codec; |
| |
| wg_time = snd_soc_read(codec, WCD9XXX_A_RX_HPH_CNP_WG_TIME); |
| wg_time += 1; |
| |
| /* If headphone PA is on, check if userspace receives |
| * removal event to sync-up PA's state */ |
| if (wcd9xxx_is_hph_pa_on(codec)) { |
| pr_debug("%s PA is on, setting PA_OFF_ACK\n", __func__); |
| set_bit(WCD9XXX_HPHL_PA_OFF_ACK, &mbhc->hph_pa_dac_state); |
| set_bit(WCD9XXX_HPHR_PA_OFF_ACK, &mbhc->hph_pa_dac_state); |
| } else { |
| pr_debug("%s PA is off\n", __func__); |
| } |
| |
| if (wcd9xxx_is_hph_dac_on(codec, 1)) |
| set_bit(WCD9XXX_HPHL_DAC_OFF_ACK, &mbhc->hph_pa_dac_state); |
| if (wcd9xxx_is_hph_dac_on(codec, 0)) |
| set_bit(WCD9XXX_HPHR_DAC_OFF_ACK, &mbhc->hph_pa_dac_state); |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_RX_HPH_CNP_EN, 0x30, 0x00); |
| snd_soc_update_bits(codec, WCD9XXX_A_RX_HPH_L_DAC_CTL, 0x80, 0x00); |
| snd_soc_update_bits(codec, WCD9XXX_A_RX_HPH_R_DAC_CTL, 0xC0, 0x00); |
| usleep_range(wg_time * 1000, wg_time * 1000); |
| } |
| |
| static void wcd9xxx_insert_detect_setup(struct wcd9xxx_mbhc *mbhc, bool ins) |
| { |
| if (!mbhc->mbhc_cfg->insert_detect) |
| return; |
| pr_debug("%s: Setting up %s detection\n", __func__, |
| ins ? "insert" : "removal"); |
| /* Disable detection to avoid glitch */ |
| snd_soc_update_bits(mbhc->codec, WCD9XXX_A_MBHC_INSERT_DETECT, 1, 0); |
| if (mbhc->mbhc_cfg->gpio_level_insert) |
| snd_soc_write(mbhc->codec, WCD9XXX_A_MBHC_INSERT_DETECT, |
| (0x68 | (ins ? (1 << 1) : 0))); |
| else |
| snd_soc_write(mbhc->codec, WCD9XXX_A_MBHC_INSERT_DETECT, |
| (0x6C | (ins ? (1 << 1) : 0))); |
| /* Re-enable detection */ |
| snd_soc_update_bits(mbhc->codec, WCD9XXX_A_MBHC_INSERT_DETECT, 1, 1); |
| } |
| |
| /* called under codec_resource_lock acquisition */ |
| static void wcd9xxx_report_plug(struct wcd9xxx_mbhc *mbhc, int insertion, |
| enum snd_jack_types jack_type) |
| { |
| WCD9XXX_BCL_ASSERT_LOCKED(mbhc->resmgr); |
| |
| pr_debug("%s: enter insertion %d hph_status %x\n", |
| __func__, insertion, mbhc->hph_status); |
| if (!insertion) { |
| /* Report removal */ |
| mbhc->hph_status &= ~jack_type; |
| /* |
| * cancel possibly scheduled btn work and |
| * report release if we reported button press |
| */ |
| if (wcd9xxx_cancel_btn_work(mbhc)) |
| pr_debug("%s: button press is canceled\n", __func__); |
| else if (mbhc->buttons_pressed) { |
| pr_debug("%s: release of button press%d\n", |
| __func__, jack_type); |
| wcd9xxx_jack_report(mbhc, &mbhc->button_jack, 0, |
| mbhc->buttons_pressed); |
| mbhc->buttons_pressed &= |
| ~WCD9XXX_JACK_BUTTON_MASK; |
| } |
| |
| if (mbhc->micbias_enable && mbhc->micbias_enable_cb) { |
| pr_debug("%s: Disabling micbias\n", __func__); |
| mbhc->micbias_enable_cb(mbhc->codec, false); |
| mbhc->micbias_enable = false; |
| } |
| mbhc->zl = mbhc->zr = 0; |
| pr_debug("%s: Reporting removal %d(%x)\n", __func__, |
| jack_type, mbhc->hph_status); |
| wcd9xxx_jack_report(mbhc, &mbhc->headset_jack, mbhc->hph_status, |
| WCD9XXX_JACK_MASK); |
| wcd9xxx_set_and_turnoff_hph_padac(mbhc); |
| hphrocp_off_report(mbhc, SND_JACK_OC_HPHR); |
| hphlocp_off_report(mbhc, SND_JACK_OC_HPHL); |
| mbhc->current_plug = PLUG_TYPE_NONE; |
| mbhc->polling_active = false; |
| } else { |
| if (mbhc->mbhc_cfg->detect_extn_cable) { |
| /* Report removal of current jack type */ |
| if (mbhc->hph_status && mbhc->hph_status != jack_type) { |
| if (mbhc->micbias_enable && |
| mbhc->micbias_enable_cb && |
| mbhc->hph_status == SND_JACK_HEADSET) { |
| pr_debug("%s: Disabling micbias\n", |
| __func__); |
| mbhc->micbias_enable_cb(mbhc->codec, |
| false); |
| mbhc->micbias_enable = false; |
| } |
| pr_debug("%s: Reporting removal (%x)\n", |
| __func__, mbhc->hph_status); |
| mbhc->zl = mbhc->zr = 0; |
| wcd9xxx_jack_report(mbhc, &mbhc->headset_jack, |
| 0, WCD9XXX_JACK_MASK); |
| mbhc->hph_status = 0; |
| } |
| } |
| /* Report insertion */ |
| mbhc->hph_status |= jack_type; |
| |
| if (jack_type == SND_JACK_HEADPHONE) { |
| mbhc->current_plug = PLUG_TYPE_HEADPHONE; |
| } else if (jack_type == SND_JACK_UNSUPPORTED) { |
| mbhc->current_plug = PLUG_TYPE_GND_MIC_SWAP; |
| } else if (jack_type == SND_JACK_HEADSET) { |
| mbhc->polling_active = BUTTON_POLLING_SUPPORTED; |
| mbhc->current_plug = PLUG_TYPE_HEADSET; |
| mbhc->update_z = true; |
| } else if (jack_type == SND_JACK_LINEOUT) { |
| mbhc->current_plug = PLUG_TYPE_HIGH_HPH; |
| } |
| |
| if (mbhc->micbias_enable && mbhc->micbias_enable_cb) { |
| pr_debug("%s: Enabling micbias\n", __func__); |
| mbhc->micbias_enable_cb(mbhc->codec, true); |
| } |
| |
| if (mbhc->impedance_detect && impedance_detect_en) |
| wcd9xxx_detect_impedance(mbhc, &mbhc->zl, &mbhc->zr); |
| |
| pr_debug("%s: Reporting insertion %d(%x)\n", __func__, |
| jack_type, mbhc->hph_status); |
| wcd9xxx_jack_report(mbhc, &mbhc->headset_jack, |
| mbhc->hph_status, WCD9XXX_JACK_MASK); |
| wcd9xxx_clr_and_turnon_hph_padac(mbhc); |
| } |
| /* Setup insert detect */ |
| wcd9xxx_insert_detect_setup(mbhc, !insertion); |
| |
| pr_debug("%s: leave hph_status %x\n", __func__, mbhc->hph_status); |
| } |
| |
| /* should be called under interrupt context that hold suspend */ |
| static void wcd9xxx_schedule_hs_detect_plug(struct wcd9xxx_mbhc *mbhc, |
| struct work_struct *work) |
| { |
| pr_debug("%s: scheduling wcd9xxx_correct_swch_plug\n", __func__); |
| WCD9XXX_BCL_ASSERT_LOCKED(mbhc->resmgr); |
| mbhc->hs_detect_work_stop = false; |
| wcd9xxx_lock_sleep(mbhc->resmgr->core_res); |
| schedule_work(work); |
| } |
| |
| /* called under codec_resource_lock acquisition */ |
| static void wcd9xxx_cancel_hs_detect_plug(struct wcd9xxx_mbhc *mbhc, |
| struct work_struct *work) |
| { |
| pr_debug("%s: Canceling correct_plug_swch\n", __func__); |
| WCD9XXX_BCL_ASSERT_LOCKED(mbhc->resmgr); |
| mbhc->hs_detect_work_stop = true; |
| wmb(); |
| WCD9XXX_BCL_UNLOCK(mbhc->resmgr); |
| if (cancel_work_sync(work)) { |
| pr_debug("%s: correct_plug_swch is canceled\n", |
| __func__); |
| wcd9xxx_unlock_sleep(mbhc->resmgr->core_res); |
| } |
| WCD9XXX_BCL_LOCK(mbhc->resmgr); |
| } |
| |
| static s16 scale_v_micb_vddio(struct wcd9xxx_mbhc *mbhc, int v, bool tovddio) |
| { |
| int r; |
| int vddio_k, mb_k; |
| vddio_k = __wcd9xxx_resmgr_get_k_val(mbhc, VDDIO_MICBIAS_MV); |
| mb_k = __wcd9xxx_resmgr_get_k_val(mbhc, mbhc->mbhc_data.micb_mv); |
| if (tovddio) |
| r = v * (vddio_k + 4) / (mb_k + 4); |
| else |
| r = v * (mb_k + 4) / (vddio_k + 4); |
| return r; |
| } |
| |
| static s16 wcd9xxx_get_current_v_hs_max(struct wcd9xxx_mbhc *mbhc) |
| { |
| s16 v_hs_max; |
| struct wcd9xxx_mbhc_plug_type_cfg *plug_type; |
| |
| plug_type = WCD9XXX_MBHC_CAL_PLUG_TYPE_PTR(mbhc->mbhc_cfg->calibration); |
| if ((mbhc->mbhc_data.micb_mv != VDDIO_MICBIAS_MV) && |
| mbhc->mbhc_micbias_switched) |
| v_hs_max = scale_v_micb_vddio(mbhc, plug_type->v_hs_max, true); |
| else |
| v_hs_max = plug_type->v_hs_max; |
| return v_hs_max; |
| } |
| |
| static short wcd9xxx_read_sta_result(struct snd_soc_codec *codec) |
| { |
| u8 bias_msb, bias_lsb; |
| short bias_value; |
| |
| bias_msb = snd_soc_read(codec, WCD9XXX_A_CDC_MBHC_B3_STATUS); |
| bias_lsb = snd_soc_read(codec, WCD9XXX_A_CDC_MBHC_B2_STATUS); |
| bias_value = (bias_msb << 8) | bias_lsb; |
| return bias_value; |
| } |
| |
| static short wcd9xxx_read_dce_result(struct snd_soc_codec *codec) |
| { |
| u8 bias_msb, bias_lsb; |
| short bias_value; |
| |
| bias_msb = snd_soc_read(codec, WCD9XXX_A_CDC_MBHC_B5_STATUS); |
| bias_lsb = snd_soc_read(codec, WCD9XXX_A_CDC_MBHC_B4_STATUS); |
| bias_value = (bias_msb << 8) | bias_lsb; |
| return bias_value; |
| } |
| |
| static void wcd9xxx_turn_onoff_rel_detection(struct snd_soc_codec *codec, |
| bool on) |
| { |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, 0x02, on << 1); |
| } |
| |
| static short __wcd9xxx_codec_sta_dce(struct wcd9xxx_mbhc *mbhc, int dce, |
| bool override_bypass, bool noreldetection) |
| { |
| short bias_value; |
| struct snd_soc_codec *codec = mbhc->codec; |
| |
| wcd9xxx_disable_irq(mbhc->resmgr->core_res, WCD9XXX_IRQ_MBHC_POTENTIAL); |
| if (noreldetection) |
| wcd9xxx_turn_onoff_rel_detection(codec, false); |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x2, 0x0); |
| /* Turn on the override */ |
| if (!override_bypass) |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, 0x4, 0x4); |
| if (dce) { |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x8, |
| 0x8); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_EN_CTL, 0x4); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x8, |
| 0x0); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x2, |
| 0x2); |
| usleep_range(mbhc->mbhc_data.t_sta_dce, |
| mbhc->mbhc_data.t_sta_dce); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_EN_CTL, 0x4); |
| usleep_range(mbhc->mbhc_data.t_dce, mbhc->mbhc_data.t_dce); |
| bias_value = wcd9xxx_read_dce_result(codec); |
| } else { |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x8, |
| 0x8); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_EN_CTL, 0x2); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x8, |
| 0x0); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x2, |
| 0x2); |
| usleep_range(mbhc->mbhc_data.t_sta_dce, |
| mbhc->mbhc_data.t_sta_dce); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_EN_CTL, 0x2); |
| usleep_range(mbhc->mbhc_data.t_sta, |
| mbhc->mbhc_data.t_sta); |
| bias_value = wcd9xxx_read_sta_result(codec); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x8, |
| 0x8); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_EN_CTL, 0x0); |
| } |
| /* Turn off the override after measuring mic voltage */ |
| if (!override_bypass) |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, 0x04, |
| 0x00); |
| |
| if (noreldetection) |
| wcd9xxx_turn_onoff_rel_detection(codec, true); |
| wcd9xxx_enable_irq(mbhc->resmgr->core_res, WCD9XXX_IRQ_MBHC_POTENTIAL); |
| |
| return bias_value; |
| } |
| |
| static short wcd9xxx_codec_sta_dce(struct wcd9xxx_mbhc *mbhc, int dce, |
| bool norel) |
| { |
| return __wcd9xxx_codec_sta_dce(mbhc, dce, false, norel); |
| } |
| |
| static s32 __wcd9xxx_codec_sta_dce_v(struct wcd9xxx_mbhc *mbhc, s8 dce, |
| u16 bias_value, s16 z, u32 micb_mv) |
| { |
| s16 value, mb; |
| s32 mv; |
| |
| value = bias_value; |
| if (dce) { |
| mb = (mbhc->mbhc_data.dce_mb); |
| mv = (value - z) * (s32)micb_mv / (mb - z); |
| } else { |
| mb = (mbhc->mbhc_data.sta_mb); |
| mv = (value - z) * (s32)micb_mv / (mb - z); |
| } |
| |
| return mv; |
| } |
| |
| static s32 wcd9xxx_codec_sta_dce_v(struct wcd9xxx_mbhc *mbhc, s8 dce, |
| u16 bias_value) |
| { |
| s16 z; |
| z = dce ? (s16)mbhc->mbhc_data.dce_z : (s16)mbhc->mbhc_data.sta_z; |
| return __wcd9xxx_codec_sta_dce_v(mbhc, dce, bias_value, z, |
| mbhc->mbhc_data.micb_mv); |
| } |
| |
| /* called only from interrupt which is under codec_resource_lock acquisition */ |
| static short wcd9xxx_mbhc_setup_hs_polling(struct wcd9xxx_mbhc *mbhc, |
| bool is_cs_enable) |
| { |
| struct snd_soc_codec *codec = mbhc->codec; |
| short bias_value; |
| u8 cfilt_mode; |
| s16 reg; |
| int change; |
| struct wcd9xxx_mbhc_btn_detect_cfg *btn_det; |
| s16 sta_z = 0, dce_z = 0; |
| |
| WCD9XXX_BCL_ASSERT_LOCKED(mbhc->resmgr); |
| |
| pr_debug("%s: enter\n", __func__); |
| if (!mbhc->mbhc_cfg->calibration) { |
| pr_err("%s: Error, no calibration exists\n", __func__); |
| return -ENODEV; |
| } |
| |
| btn_det = WCD9XXX_MBHC_CAL_BTN_DET_PTR(mbhc->mbhc_cfg->calibration); |
| /* Enable external voltage source to micbias if present */ |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mb_source) |
| mbhc->mbhc_cb->enable_mb_source(codec, true); |
| |
| /* |
| * setup internal micbias if codec uses internal micbias for |
| * headset detection |
| */ |
| if (mbhc->mbhc_cfg->use_int_rbias) { |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->setup_int_rbias) |
| mbhc->mbhc_cb->setup_int_rbias(codec, true); |
| else |
| pr_err("%s: internal bias is requested but codec did not provide callback\n", |
| __func__); |
| } |
| |
| /* |
| * Request BG and clock. |
| * These will be released by wcd9xxx_cleanup_hs_polling |
| */ |
| WCD9XXX_BG_CLK_LOCK(mbhc->resmgr); |
| wcd9xxx_resmgr_get_bandgap(mbhc->resmgr, WCD9XXX_BANDGAP_AUDIO_MODE); |
| wcd9xxx_resmgr_get_clk_block(mbhc->resmgr, WCD9XXX_CLK_RCO); |
| WCD9XXX_BG_CLK_UNLOCK(mbhc->resmgr); |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_CLK_BUFF_EN1, 0x05, 0x01); |
| |
| /* Make sure CFILT is in fast mode, save current mode */ |
| cfilt_mode = snd_soc_read(codec, mbhc->mbhc_bias_regs.cfilt_ctl); |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->cfilt_fast_mode) |
| mbhc->mbhc_cb->cfilt_fast_mode(codec, mbhc); |
| else |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.cfilt_ctl, |
| 0x70, 0x00); |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x2, 0x2); |
| snd_soc_write(codec, WCD9XXX_A_MBHC_SCALING_MUX_1, 0x04); |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mux_bias_block) |
| mbhc->mbhc_cb->enable_mux_bias_block(codec); |
| else |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_SCALING_MUX_1, |
| 0x80, 0x80); |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_TX_7_MBHC_EN, 0x80, 0x80); |
| snd_soc_update_bits(codec, WCD9XXX_A_TX_7_MBHC_EN, 0x1F, 0x1C); |
| snd_soc_update_bits(codec, WCD9XXX_A_TX_7_MBHC_TEST_CTL, 0x40, 0x40); |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_TX_7_MBHC_EN, 0x80, 0x00); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x8, 0x8); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x8, 0x00); |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, 0x2, 0x2); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x8, 0x8); |
| |
| /* don't flip override */ |
| bias_value = __wcd9xxx_codec_sta_dce(mbhc, 1, true, true); |
| snd_soc_write(codec, mbhc->mbhc_bias_regs.cfilt_ctl, cfilt_mode); |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_HPH, 0x13, 0x00); |
| |
| /* recalibrate dce_z and sta_z */ |
| reg = snd_soc_read(codec, WCD9XXX_A_CDC_MBHC_B1_CTL); |
| change = snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, 0x78, |
| btn_det->mbhc_nsc << 3); |
| wcd9xxx_get_z(mbhc, &dce_z, &sta_z); |
| if (change) |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, reg); |
| if (dce_z && sta_z) { |
| pr_debug("%s: sta_z 0x%x -> 0x%x, dce_z 0x%x -> 0x%x\n", |
| __func__, |
| mbhc->mbhc_data.sta_z, sta_z & 0xffff, |
| mbhc->mbhc_data.dce_z, dce_z & 0xffff); |
| mbhc->mbhc_data.dce_z = dce_z; |
| mbhc->mbhc_data.sta_z = sta_z; |
| wcd9xxx_mbhc_calc_thres(mbhc); |
| wcd9xxx_calibrate_hs_polling(mbhc); |
| } else { |
| pr_warn("%s: failed get new dce_z/sta_z 0x%x/0x%x\n", __func__, |
| dce_z, sta_z); |
| } |
| |
| if (is_cs_enable) { |
| /* recalibrate dce_nsc_cs_z */ |
| reg = snd_soc_read(mbhc->codec, WCD9XXX_A_CDC_MBHC_B1_CTL); |
| snd_soc_update_bits(mbhc->codec, WCD9XXX_A_CDC_MBHC_B1_CTL, |
| 0x78, WCD9XXX_MBHC_NSC_CS << 3); |
| wcd9xxx_get_z(mbhc, &dce_z, NULL); |
| snd_soc_write(mbhc->codec, WCD9XXX_A_CDC_MBHC_B1_CTL, reg); |
| if (dce_z) { |
| pr_debug("%s: dce_nsc_cs_z 0x%x -> 0x%x\n", __func__, |
| mbhc->mbhc_data.dce_nsc_cs_z, dce_z & 0xffff); |
| mbhc->mbhc_data.dce_nsc_cs_z = dce_z; |
| } else { |
| pr_debug("%s: failed get new dce_nsc_cs_z\n", __func__); |
| } |
| } |
| |
| return bias_value; |
| } |
| |
| static void wcd9xxx_shutdown_hs_removal_detect(struct wcd9xxx_mbhc *mbhc) |
| { |
| struct snd_soc_codec *codec = mbhc->codec; |
| const struct wcd9xxx_mbhc_general_cfg *generic = |
| WCD9XXX_MBHC_CAL_GENERAL_PTR(mbhc->mbhc_cfg->calibration); |
| |
| /* Need MBHC clock */ |
| WCD9XXX_BG_CLK_LOCK(mbhc->resmgr); |
| wcd9xxx_resmgr_get_clk_block(mbhc->resmgr, WCD9XXX_CLK_RCO); |
| WCD9XXX_BG_CLK_UNLOCK(mbhc->resmgr); |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x2, 0x2); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, 0x6, 0x0); |
| __wcd9xxx_switch_micbias(mbhc, 0, false, false); |
| |
| usleep_range(generic->t_shutdown_plug_rem, |
| generic->t_shutdown_plug_rem); |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0xA, 0x8); |
| |
| WCD9XXX_BG_CLK_LOCK(mbhc->resmgr); |
| /* Put requested CLK back */ |
| wcd9xxx_resmgr_put_clk_block(mbhc->resmgr, WCD9XXX_CLK_RCO); |
| WCD9XXX_BG_CLK_UNLOCK(mbhc->resmgr); |
| |
| snd_soc_write(codec, WCD9XXX_A_MBHC_SCALING_MUX_1, 0x00); |
| } |
| |
| static void wcd9xxx_cleanup_hs_polling(struct wcd9xxx_mbhc *mbhc) |
| { |
| |
| pr_debug("%s: enter\n", __func__); |
| WCD9XXX_BCL_ASSERT_LOCKED(mbhc->resmgr); |
| |
| wcd9xxx_shutdown_hs_removal_detect(mbhc); |
| |
| /* Release clock and BG requested by wcd9xxx_mbhc_setup_hs_polling */ |
| WCD9XXX_BG_CLK_LOCK(mbhc->resmgr); |
| wcd9xxx_resmgr_put_clk_block(mbhc->resmgr, WCD9XXX_CLK_RCO); |
| wcd9xxx_resmgr_put_bandgap(mbhc->resmgr, WCD9XXX_BANDGAP_MBHC_MODE); |
| WCD9XXX_BG_CLK_UNLOCK(mbhc->resmgr); |
| |
| /* Disable external voltage source to micbias if present */ |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mb_source) |
| mbhc->mbhc_cb->enable_mb_source(mbhc->codec, false); |
| |
| mbhc->polling_active = false; |
| mbhc->mbhc_state = MBHC_STATE_NONE; |
| pr_debug("%s: leave\n", __func__); |
| } |
| |
| /* called under codec_resource_lock acquisition */ |
| static void wcd9xxx_codec_hphr_gnd_switch(struct snd_soc_codec *codec, bool on) |
| { |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_HPH, 0x01, on); |
| if (on) |
| usleep_range(5000, 5000); |
| } |
| |
| static void wcd9xxx_onoff_vddio_switch(struct wcd9xxx_mbhc *mbhc, bool on) |
| { |
| pr_debug("%s: vddio %d\n", __func__, on); |
| |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->pull_mb_to_vddio) { |
| mbhc->mbhc_cb->pull_mb_to_vddio(mbhc->codec, on); |
| goto exit; |
| } |
| |
| if (on) { |
| snd_soc_update_bits(mbhc->codec, mbhc->mbhc_bias_regs.mbhc_reg, |
| 1 << 7, 1 << 7); |
| snd_soc_update_bits(mbhc->codec, WCD9XXX_A_MAD_ANA_CTRL, |
| 1 << 4, 0); |
| } else { |
| snd_soc_update_bits(mbhc->codec, WCD9XXX_A_MAD_ANA_CTRL, |
| 1 << 4, 1 << 4); |
| snd_soc_update_bits(mbhc->codec, mbhc->mbhc_bias_regs.mbhc_reg, |
| 1 << 7, 0); |
| } |
| |
| exit: |
| /* |
| * Wait for the micbias to settle down to vddio |
| * when the micbias to vddio switch is enabled. |
| */ |
| if (on) |
| usleep_range(10000, 10000); |
| } |
| |
| static int wcd9xxx_hphl_status(struct wcd9xxx_mbhc *mbhc) |
| { |
| u16 hph, status; |
| struct snd_soc_codec *codec = mbhc->codec; |
| |
| WCD9XXX_BCL_ASSERT_LOCKED(mbhc->resmgr); |
| hph = snd_soc_read(codec, WCD9XXX_A_MBHC_HPH); |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_HPH, 0x12, 0x02); |
| usleep_range(WCD9XXX_HPHL_STATUS_READY_WAIT_US, |
| WCD9XXX_HPHL_STATUS_READY_WAIT_US + |
| WCD9XXX_USLEEP_RANGE_MARGIN_US); |
| status = snd_soc_read(codec, WCD9XXX_A_RX_HPH_L_STATUS); |
| snd_soc_write(codec, WCD9XXX_A_MBHC_HPH, hph); |
| return status; |
| } |
| |
| static enum wcd9xxx_mbhc_plug_type |
| wcd9xxx_cs_find_plug_type(struct wcd9xxx_mbhc *mbhc, |
| struct wcd9xxx_mbhc_detect *dt, const int size, |
| bool highhph, |
| unsigned long event_state) |
| { |
| int i; |
| int vdce, mb_mv; |
| int ch, sz, delta_thr; |
| int minv = 0, maxv = INT_MIN; |
| struct wcd9xxx_mbhc_detect *d = dt; |
| struct wcd9xxx_mbhc_detect *dprev = d, *dmicbias = NULL, *dgnd = NULL; |
| enum wcd9xxx_mbhc_plug_type type = PLUG_TYPE_INVALID; |
| |
| const struct wcd9xxx_mbhc_plug_type_cfg *plug_type = |
| WCD9XXX_MBHC_CAL_PLUG_TYPE_PTR(mbhc->mbhc_cfg->calibration); |
| s16 hs_max, no_mic, dce_z; |
| |
| pr_debug("%s: enter\n", __func__); |
| pr_debug("%s: event_state 0x%lx\n", __func__, event_state); |
| |
| sz = size - 1; |
| for (i = 0, d = dt, ch = 0; i < sz; i++, d++) { |
| if (d->mic_bias) { |
| dce_z = mbhc->mbhc_data.dce_z; |
| mb_mv = mbhc->mbhc_data.micb_mv; |
| hs_max = plug_type->v_hs_max; |
| no_mic = plug_type->v_no_mic; |
| } else { |
| dce_z = mbhc->mbhc_data.dce_nsc_cs_z; |
| mb_mv = VDDIO_MICBIAS_MV; |
| hs_max = WCD9XXX_V_CS_HS_MAX; |
| no_mic = WCD9XXX_V_CS_NO_MIC; |
| } |
| |
| vdce = __wcd9xxx_codec_sta_dce_v(mbhc, true, d->dce, |
| dce_z, (u32)mb_mv); |
| |
| d->_vdces = vdce; |
| if (d->_vdces < no_mic) |
| d->_type = PLUG_TYPE_HEADPHONE; |
| else if (d->_vdces >= hs_max) |
| d->_type = PLUG_TYPE_HIGH_HPH; |
| else |
| d->_type = PLUG_TYPE_HEADSET; |
| |
| pr_debug("%s: DCE #%d, %04x, V %04d(%04d), HPHL %d TYPE %d\n", |
| __func__, i, d->dce, vdce, d->_vdces, |
| d->hphl_status & 0x01, |
| d->_type); |
| |
| ch += d->hphl_status & 0x01; |
| if (!d->swap_gnd && !d->mic_bias) { |
| if (maxv < d->_vdces) |
| maxv = d->_vdces; |
| if (!minv || minv > d->_vdces) |
| minv = d->_vdces; |
| } |
| if ((!d->mic_bias && |
| (d->_vdces >= WCD9XXX_CS_MEAS_INVALD_RANGE_LOW_MV && |
| d->_vdces <= WCD9XXX_CS_MEAS_INVALD_RANGE_HIGH_MV)) || |
| (d->mic_bias && |
| (d->_vdces >= WCD9XXX_MEAS_INVALD_RANGE_LOW_MV && |
| d->_vdces <= WCD9XXX_MEAS_INVALD_RANGE_HIGH_MV))) { |
| pr_debug("%s: within invalid range\n", __func__); |
| type = PLUG_TYPE_INVALID; |
| goto exit; |
| } |
| } |
| |
| if (event_state & (1 << MBHC_EVENT_PA_HPHL)) { |
| pr_debug("%s: HPHL PA was ON\n", __func__); |
| } else if (ch != sz && ch > 0) { |
| pr_debug("%s: Invalid, inconsistent HPHL\n", __func__); |
| type = PLUG_TYPE_INVALID; |
| goto exit; |
| } |
| |
| delta_thr = highhph ? WCD9XXX_MB_MEAS_DELTA_MAX_MV : |
| WCD9XXX_CS_MEAS_DELTA_MAX_MV; |
| |
| for (i = 0, d = dt; i < sz; i++, d++) { |
| if ((i > 0) && !d->mic_bias && !d->swap_gnd && |
| (d->_type != dprev->_type)) { |
| pr_debug("%s: Invalid, inconsistent types\n", __func__); |
| type = PLUG_TYPE_INVALID; |
| goto exit; |
| } |
| |
| if (!d->swap_gnd && !d->mic_bias && |
| (abs(minv - d->_vdces) > delta_thr || |
| abs(maxv - d->_vdces) > delta_thr)) { |
| pr_debug("%s: Invalid, delta %dmv, %dmv and %dmv\n", |
| __func__, d->_vdces, minv, maxv); |
| type = PLUG_TYPE_INVALID; |
| goto exit; |
| } else if (d->swap_gnd) { |
| dgnd = d; |
| } |
| |
| if (!d->mic_bias && !d->swap_gnd) |
| dprev = d; |
| else if (d->mic_bias) |
| dmicbias = d; |
| } |
| if (dgnd && dt->_type != PLUG_TYPE_HEADSET && |
| dt->_type != dgnd->_type) { |
| pr_debug("%s: Invalid, inconsistent types\n", __func__); |
| type = PLUG_TYPE_INVALID; |
| goto exit; |
| } |
| |
| type = dt->_type; |
| if (dmicbias) { |
| if (dmicbias->_type == PLUG_TYPE_HEADSET && |
| (dt->_type == PLUG_TYPE_HIGH_HPH || |
| dt->_type == PLUG_TYPE_HEADSET)) { |
| type = PLUG_TYPE_HEADSET; |
| if (dt->_type == PLUG_TYPE_HIGH_HPH) { |
| pr_debug("%s: Headset with threshold on MIC detected\n", |
| __func__); |
| if (mbhc->mbhc_cfg->micbias_enable_flags & |
| (1 << MBHC_MICBIAS_ENABLE_THRESHOLD_HEADSET)) |
| mbhc->micbias_enable = true; |
| } |
| } |
| } |
| |
| if (!(event_state & (1UL << MBHC_EVENT_PA_HPHL))) { |
| if (((type == PLUG_TYPE_HEADSET || |
| type == PLUG_TYPE_HEADPHONE) && ch != sz)) { |
| pr_debug("%s: Invalid, not fully inserted, TYPE %d\n", |
| __func__, type); |
| type = PLUG_TYPE_INVALID; |
| } |
| } |
| if (type == PLUG_TYPE_HEADSET && dgnd && !dgnd->mic_bias) { |
| if ((dgnd->_vdces + WCD9XXX_CS_GM_SWAP_THRES_MIN_MV < |
| minv) && |
| (dgnd->_vdces + WCD9XXX_CS_GM_SWAP_THRES_MAX_MV > |
| maxv)) |
| type = PLUG_TYPE_GND_MIC_SWAP; |
| else if (dgnd->_type != PLUG_TYPE_HEADSET && !dmicbias) { |
| pr_debug("%s: Invalid, inconsistent types\n", __func__); |
| type = PLUG_TYPE_INVALID; |
| } |
| } |
| exit: |
| pr_debug("%s: Plug type %d detected\n", __func__, type); |
| return type; |
| } |
| |
| /* |
| * wcd9xxx_find_plug_type : Find out and return the best plug type with given |
| * list of wcd9xxx_mbhc_detect structure. |
| * param mbhc wcd9xxx_mbhc structure |
| * param dt collected measurements |
| * param size array size of dt |
| * param event_state mbhc->event_state when dt is collected |
| */ |
| static enum wcd9xxx_mbhc_plug_type |
| wcd9xxx_find_plug_type(struct wcd9xxx_mbhc *mbhc, |
| struct wcd9xxx_mbhc_detect *dt, const int size, |
| unsigned long event_state) |
| { |
| int i; |
| int ch; |
| enum wcd9xxx_mbhc_plug_type type; |
| int vdce; |
| struct wcd9xxx_mbhc_detect *d, *dprev, *dgnd = NULL, *dvddio = NULL; |
| int maxv = 0, minv = 0; |
| const struct wcd9xxx_mbhc_plug_type_cfg *plug_type = |
| WCD9XXX_MBHC_CAL_PLUG_TYPE_PTR(mbhc->mbhc_cfg->calibration); |
| const s16 hs_max = plug_type->v_hs_max; |
| const s16 no_mic = plug_type->v_no_mic; |
| |
| pr_debug("%s: event_state 0x%lx\n", __func__, event_state); |
| |
| for (i = 0, d = dt, ch = 0; i < size; i++, d++) { |
| vdce = wcd9xxx_codec_sta_dce_v(mbhc, true, d->dce); |
| if (d->vddio) |
| d->_vdces = scale_v_micb_vddio(mbhc, vdce, false); |
| else |
| d->_vdces = vdce; |
| |
| if (d->_vdces >= no_mic && d->_vdces < hs_max) |
| d->_type = PLUG_TYPE_HEADSET; |
| else if (d->_vdces < no_mic) |
| d->_type = PLUG_TYPE_HEADPHONE; |
| else |
| d->_type = PLUG_TYPE_HIGH_HPH; |
| |
| ch += d->hphl_status & 0x01; |
| if (!d->swap_gnd && !d->hwvalue && !d->vddio) { |
| if (maxv < d->_vdces) |
| maxv = d->_vdces; |
| if (!minv || minv > d->_vdces) |
| minv = d->_vdces; |
| } |
| |
| pr_debug("%s: DCE #%d, %04x, V %04d(%04d), GND %d, VDDIO %d, HPHL %d TYPE %d\n", |
| __func__, i, d->dce, vdce, d->_vdces, |
| d->swap_gnd, d->vddio, d->hphl_status & 0x01, |
| d->_type); |
| |
| |
| /* |
| * If GND and MIC prongs are aligned to HPHR and GND of |
| * headphone, codec measures the voltage based on |
| * impedance between HPHR and GND which results in ~80mv. |
| * Avoid this. |
| */ |
| if (d->_vdces >= WCD9XXX_MEAS_INVALD_RANGE_LOW_MV && |
| d->_vdces <= WCD9XXX_MEAS_INVALD_RANGE_HIGH_MV) { |
| pr_debug("%s: within invalid range\n", __func__); |
| type = PLUG_TYPE_INVALID; |
| goto exit; |
| } |
| } |
| |
| if (event_state & (1 << MBHC_EVENT_PA_HPHL)) { |
| pr_debug("%s: HPHL PA was ON\n", __func__); |
| } else if (ch != size && ch > 0) { |
| pr_debug("%s: Invalid, inconsistent HPHL\n", __func__); |
| type = PLUG_TYPE_INVALID; |
| goto exit; |
| } |
| |
| for (i = 0, dprev = NULL, d = dt; i < size; i++, d++) { |
| if (d->vddio) { |
| dvddio = d; |
| continue; |
| } |
| |
| if ((i > 0) && (d->_type != dprev->_type)) { |
| pr_debug("%s: Invalid, inconsistent types\n", __func__); |
| type = PLUG_TYPE_INVALID; |
| goto exit; |
| } |
| |
| if (!d->swap_gnd && !d->hwvalue && |
| (abs(minv - d->_vdces) > WCD9XXX_MEAS_DELTA_MAX_MV || |
| abs(maxv - d->_vdces) > WCD9XXX_MEAS_DELTA_MAX_MV)) { |
| pr_debug("%s: Invalid, delta %dmv, %dmv and %dmv\n", |
| __func__, d->_vdces, minv, maxv); |
| type = PLUG_TYPE_INVALID; |
| goto exit; |
| } else if (d->swap_gnd) { |
| dgnd = d; |
| } |
| dprev = d; |
| } |
| |
| WARN_ON(i != size); |
| type = dt->_type; |
| if (type == PLUG_TYPE_HEADSET && dgnd) { |
| if ((dgnd->_vdces + WCD9XXX_GM_SWAP_THRES_MIN_MV < |
| minv) && |
| (dgnd->_vdces + WCD9XXX_GM_SWAP_THRES_MAX_MV > |
| maxv)) |
| type = PLUG_TYPE_GND_MIC_SWAP; |
| } |
| |
| /* if HPHL PA was on, we cannot use hphl status */ |
| if (!(event_state & (1UL << MBHC_EVENT_PA_HPHL))) { |
| if (((type == PLUG_TYPE_HEADSET || |
| type == PLUG_TYPE_HEADPHONE) && ch != size) || |
| (type == PLUG_TYPE_GND_MIC_SWAP && ch)) { |
| pr_debug("%s: Invalid, not fully inserted, TYPE %d\n", |
| __func__, type); |
| type = PLUG_TYPE_INVALID; |
| } |
| } |
| |
| if (type == PLUG_TYPE_HEADSET && dvddio) { |
| if ((dvddio->_vdces > hs_max) || |
| (dvddio->_vdces > minv + WCD9XXX_THRESHOLD_MIC_THRESHOLD)) { |
| pr_debug("%s: Headset with threshold on MIC detected\n", |
| __func__); |
| if (mbhc->mbhc_cfg->micbias_enable_flags & |
| (1 << MBHC_MICBIAS_ENABLE_THRESHOLD_HEADSET)) |
| mbhc->micbias_enable = true; |
| } else { |
| pr_debug("%s: Headset with regular MIC detected\n", |
| __func__); |
| if (mbhc->mbhc_cfg->micbias_enable_flags & |
| (1 << MBHC_MICBIAS_ENABLE_REGULAR_HEADSET)) |
| mbhc->micbias_enable = true; |
| } |
| } |
| exit: |
| pr_debug("%s: Plug type %d detected, micbias_enable %d\n", __func__, |
| type, mbhc->micbias_enable); |
| return type; |
| } |
| |
| /* |
| * Pull down MBHC micbias for provided duration in microsecond. |
| */ |
| static int wcd9xxx_pull_down_micbias(struct wcd9xxx_mbhc *mbhc, int us) |
| { |
| bool micbiasconn = false; |
| struct snd_soc_codec *codec = mbhc->codec; |
| const u16 ctlreg = mbhc->mbhc_bias_regs.ctl_reg; |
| |
| /* |
| * Disable MBHC to micbias connection to pull down |
| * micbias and pull down micbias for a moment. |
| */ |
| if ((snd_soc_read(mbhc->codec, ctlreg) & 0x01)) { |
| WARN_ONCE(1, "MBHC micbias is already pulled down unexpectedly\n"); |
| return -EFAULT; |
| } |
| |
| if ((snd_soc_read(mbhc->codec, WCD9XXX_A_MAD_ANA_CTRL) & 1 << 4)) { |
| snd_soc_update_bits(mbhc->codec, WCD9XXX_A_MAD_ANA_CTRL, |
| 1 << 4, 0); |
| micbiasconn = true; |
| } |
| |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.ctl_reg, 0x01, 0x01); |
| |
| /* |
| * Pull down for 1ms to discharge bias. Give small margin (10us) to be |
| * able to get consistent result across DCEs. |
| */ |
| usleep_range(1000, 1000 + 10); |
| |
| if (micbiasconn) |
| snd_soc_update_bits(mbhc->codec, WCD9XXX_A_MAD_ANA_CTRL, |
| 1 << 4, 1 << 4); |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.ctl_reg, 0x01, 0x00); |
| usleep_range(us, us + WCD9XXX_USLEEP_RANGE_MARGIN_US); |
| |
| return 0; |
| } |
| |
| void wcd9xxx_turn_onoff_current_source(struct wcd9xxx_mbhc *mbhc, bool on, |
| bool highhph) |
| { |
| |
| struct snd_soc_codec *codec; |
| struct wcd9xxx_mbhc_btn_detect_cfg *btn_det; |
| const struct wcd9xxx_mbhc_plug_detect_cfg *plug_det = |
| WCD9XXX_MBHC_CAL_PLUG_DET_PTR(mbhc->mbhc_cfg->calibration); |
| |
| btn_det = WCD9XXX_MBHC_CAL_BTN_DET_PTR(mbhc->mbhc_cfg->calibration); |
| codec = mbhc->codec; |
| |
| if (on) { |
| pr_debug("%s: enabling current source\n", __func__); |
| /* Nsc to 9 */ |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, |
| 0x78, 0x48); |
| /* pull down diode bit to 0 */ |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.mbhc_reg, |
| 0x01, 0x00); |
| /* |
| * Keep the low power insertion/removal |
| * detection (reg 0x3DD) disabled |
| */ |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_INT_CTL, |
| 0x01, 0x00); |
| /* |
| * Enable the Mic Bias current source |
| * Write bits[6:5] of register MICB_2_MBHC to 0x3 (V_20_UA) |
| * Write bit[7] of register MICB_2_MBHC to 1 |
| * (INS_DET_ISRC_EN__ENABLE) |
| * MICB_2_MBHC__SCHT_TRIG_EN to 1 |
| */ |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.mbhc_reg, |
| 0xF0, 0xF0); |
| /* Disconnect MBHC Override from MicBias and LDOH */ |
| snd_soc_update_bits(codec, WCD9XXX_A_MAD_ANA_CTRL, 0x10, 0x00); |
| } else { |
| pr_debug("%s: disabling current source\n", __func__); |
| /* Connect MBHC Override from MicBias and LDOH */ |
| snd_soc_update_bits(codec, WCD9XXX_A_MAD_ANA_CTRL, 0x10, 0x10); |
| /* INS_DET_ISRC_CTL to acdb value */ |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.mbhc_reg, |
| 0x60, plug_det->mic_current << 5); |
| if (!highhph) { |
| /* INS_DET_ISRC_EN__ENABLE to 0 */ |
| snd_soc_update_bits(codec, |
| mbhc->mbhc_bias_regs.mbhc_reg, |
| 0x80, 0x00); |
| /* MICB_2_MBHC__SCHT_TRIG_EN to 0 */ |
| snd_soc_update_bits(codec, |
| mbhc->mbhc_bias_regs.mbhc_reg, |
| 0x10, 0x00); |
| } |
| /* Nsc to acdb value */ |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, 0x78, |
| btn_det->mbhc_nsc << 3); |
| } |
| } |
| |
| static enum wcd9xxx_mbhc_plug_type |
| wcd9xxx_codec_cs_get_plug_type(struct wcd9xxx_mbhc *mbhc, bool highhph) |
| { |
| struct snd_soc_codec *codec = mbhc->codec; |
| struct wcd9xxx_mbhc_detect rt[NUM_DCE_PLUG_INS_DETECT]; |
| enum wcd9xxx_mbhc_plug_type type = PLUG_TYPE_INVALID; |
| int i; |
| |
| pr_debug("%s: enter\n", __func__); |
| WCD9XXX_BCL_ASSERT_LOCKED(mbhc->resmgr); |
| |
| BUG_ON(NUM_DCE_PLUG_INS_DETECT < 4); |
| |
| rt[0].swap_gnd = false; |
| rt[0].vddio = false; |
| rt[0].hwvalue = true; |
| rt[0].hphl_status = wcd9xxx_hphl_status(mbhc); |
| rt[0].dce = wcd9xxx_mbhc_setup_hs_polling(mbhc, true); |
| rt[0].mic_bias = false; |
| |
| for (i = 1; i < NUM_DCE_PLUG_INS_DETECT - 1; i++) { |
| rt[i].swap_gnd = (i == NUM_DCE_PLUG_INS_DETECT - 3); |
| rt[i].mic_bias = ((i == NUM_DCE_PLUG_INS_DETECT - 4) && |
| highhph); |
| rt[i].hphl_status = wcd9xxx_hphl_status(mbhc); |
| if (rt[i].swap_gnd) |
| wcd9xxx_codec_hphr_gnd_switch(codec, true); |
| |
| if (rt[i].mic_bias) |
| wcd9xxx_turn_onoff_current_source(mbhc, false, false); |
| |
| rt[i].dce = __wcd9xxx_codec_sta_dce(mbhc, 1, !highhph, true); |
| if (rt[i].mic_bias) |
| wcd9xxx_turn_onoff_current_source(mbhc, true, false); |
| if (rt[i].swap_gnd) |
| wcd9xxx_codec_hphr_gnd_switch(codec, false); |
| } |
| |
| type = wcd9xxx_cs_find_plug_type(mbhc, rt, ARRAY_SIZE(rt), highhph, |
| mbhc->event_state); |
| |
| pr_debug("%s: plug_type:%d\n", __func__, type); |
| |
| return type; |
| } |
| |
| static enum wcd9xxx_mbhc_plug_type |
| wcd9xxx_codec_get_plug_type(struct wcd9xxx_mbhc *mbhc, bool highhph) |
| { |
| int i; |
| bool vddioon; |
| struct wcd9xxx_mbhc_plug_type_cfg *plug_type_ptr; |
| struct wcd9xxx_mbhc_detect rt[NUM_DCE_PLUG_INS_DETECT]; |
| enum wcd9xxx_mbhc_plug_type type = PLUG_TYPE_INVALID; |
| struct snd_soc_codec *codec = mbhc->codec; |
| |
| pr_debug("%s: enter\n", __func__); |
| WCD9XXX_BCL_ASSERT_LOCKED(mbhc->resmgr); |
| |
| /* make sure override is on */ |
| WARN_ON(!(snd_soc_read(codec, WCD9XXX_A_CDC_MBHC_B1_CTL) & 0x04)); |
| |
| /* GND and MIC swap detection requires at least 2 rounds of DCE */ |
| BUG_ON(NUM_DCE_PLUG_INS_DETECT < 2); |
| |
| /* |
| * There are chances vddio switch is on and cfilt voltage is adjusted |
| * to vddio voltage even after plug type removal reported. |
| */ |
| vddioon = __wcd9xxx_switch_micbias(mbhc, 0, false, false); |
| pr_debug("%s: vddio switch was %s\n", __func__, vddioon ? "on" : "off"); |
| |
| plug_type_ptr = |
| WCD9XXX_MBHC_CAL_PLUG_TYPE_PTR(mbhc->mbhc_cfg->calibration); |
| |
| /* |
| * cfilter in fast mode requires 1ms to charge up and down micbias |
| * fully. |
| */ |
| (void) wcd9xxx_pull_down_micbias(mbhc, |
| WCD9XXX_MICBIAS_PULLDOWN_SETTLE_US); |
| rt[0].hphl_status = wcd9xxx_hphl_status(mbhc); |
| rt[0].dce = wcd9xxx_mbhc_setup_hs_polling(mbhc, false); |
| rt[0].swap_gnd = false; |
| rt[0].vddio = false; |
| rt[0].hwvalue = true; |
| for (i = 1; i < NUM_DCE_PLUG_INS_DETECT; i++) { |
| rt[i].swap_gnd = (i == NUM_DCE_PLUG_INS_DETECT - 2); |
| if (detect_use_vddio_switch) |
| rt[i].vddio = (i == 1); |
| else |
| rt[i].vddio = false; |
| rt[i].hphl_status = wcd9xxx_hphl_status(mbhc); |
| rt[i].hwvalue = false; |
| if (rt[i].swap_gnd) |
| wcd9xxx_codec_hphr_gnd_switch(codec, true); |
| if (rt[i].vddio) |
| wcd9xxx_onoff_vddio_switch(mbhc, true); |
| /* |
| * Pull down micbias to detect headset with mic which has |
| * threshold and to have more consistent voltage measurements. |
| * |
| * cfilter in fast mode requires 1ms to charge up and down |
| * micbias fully. |
| */ |
| (void) wcd9xxx_pull_down_micbias(mbhc, |
| WCD9XXX_MICBIAS_PULLDOWN_SETTLE_US); |
| rt[i].dce = __wcd9xxx_codec_sta_dce(mbhc, 1, true, true); |
| if (rt[i].vddio) |
| wcd9xxx_onoff_vddio_switch(mbhc, false); |
| if (rt[i].swap_gnd) |
| wcd9xxx_codec_hphr_gnd_switch(codec, false); |
| } |
| |
| if (vddioon) |
| __wcd9xxx_switch_micbias(mbhc, 1, false, false); |
| |
| type = wcd9xxx_find_plug_type(mbhc, rt, ARRAY_SIZE(rt), |
| mbhc->event_state); |
| |
| pr_debug("%s: leave\n", __func__); |
| return type; |
| } |
| |
| static bool wcd9xxx_swch_level_remove(struct wcd9xxx_mbhc *mbhc) |
| { |
| if (mbhc->mbhc_cfg->gpio) |
| return (gpio_get_value_cansleep(mbhc->mbhc_cfg->gpio) != |
| mbhc->mbhc_cfg->gpio_level_insert); |
| else if (mbhc->mbhc_cfg->insert_detect) |
| return snd_soc_read(mbhc->codec, |
| WCD9XXX_A_MBHC_INSERT_DET_STATUS) & |
| (1 << 2); |
| else |
| WARN(1, "Invalid jack detection configuration\n"); |
| |
| return true; |
| } |
| |
| static bool is_clk_active(struct snd_soc_codec *codec) |
| { |
| return !!(snd_soc_read(codec, WCD9XXX_A_CDC_CLK_MCLK_CTL) & 0x05); |
| } |
| |
| static int wcd9xxx_enable_hs_detect(struct wcd9xxx_mbhc *mbhc, |
| int insertion, int trigger, bool padac_off) |
| { |
| struct snd_soc_codec *codec = mbhc->codec; |
| int central_bias_enabled = 0; |
| const struct wcd9xxx_mbhc_general_cfg *generic = |
| WCD9XXX_MBHC_CAL_GENERAL_PTR(mbhc->mbhc_cfg->calibration); |
| const struct wcd9xxx_mbhc_plug_detect_cfg *plug_det = |
| WCD9XXX_MBHC_CAL_PLUG_DET_PTR(mbhc->mbhc_cfg->calibration); |
| |
| pr_debug("%s: enter insertion(%d) trigger(0x%x)\n", |
| __func__, insertion, trigger); |
| |
| if (!mbhc->mbhc_cfg->calibration) { |
| pr_err("Error, no wcd9xxx calibration\n"); |
| return -EINVAL; |
| } |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_INT_CTL, 0x1, 0); |
| |
| /* |
| * Make sure mic bias and Mic line schmitt trigger |
| * are turned OFF |
| */ |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.ctl_reg, 0x01, 0x01); |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.mbhc_reg, 0x90, 0x00); |
| |
| if (insertion) { |
| wcd9xxx_switch_micbias(mbhc, 0); |
| |
| /* DAPM can manipulate PA/DAC bits concurrently */ |
| if (padac_off == true) |
| wcd9xxx_set_and_turnoff_hph_padac(mbhc); |
| |
| if (trigger & MBHC_USE_HPHL_TRIGGER) { |
| /* Enable HPH Schmitt Trigger */ |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_HPH, 0x11, |
| 0x11); |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_HPH, 0x0C, |
| plug_det->hph_current << 2); |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_HPH, 0x02, |
| 0x02); |
| } |
| if (trigger & MBHC_USE_MB_TRIGGER) { |
| /* enable the mic line schmitt trigger */ |
| snd_soc_update_bits(codec, |
| mbhc->mbhc_bias_regs.mbhc_reg, |
| 0x60, plug_det->mic_current << 5); |
| snd_soc_update_bits(codec, |
| mbhc->mbhc_bias_regs.mbhc_reg, |
| 0x80, 0x80); |
| usleep_range(plug_det->t_mic_pid, plug_det->t_mic_pid); |
| snd_soc_update_bits(codec, |
| mbhc->mbhc_bias_regs.ctl_reg, 0x01, |
| 0x00); |
| snd_soc_update_bits(codec, |
| mbhc->mbhc_bias_regs.mbhc_reg, |
| 0x10, 0x10); |
| } |
| |
| /* setup for insetion detection */ |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_INT_CTL, 0x2, 0); |
| } else { |
| pr_debug("setup for removal detection\n"); |
| /* Make sure the HPH schmitt trigger is OFF */ |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_HPH, 0x12, 0x00); |
| |
| /* enable the mic line schmitt trigger */ |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.ctl_reg, |
| 0x01, 0x00); |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.mbhc_reg, 0x60, |
| plug_det->mic_current << 5); |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.mbhc_reg, |
| 0x80, 0x80); |
| usleep_range(plug_det->t_mic_pid, plug_det->t_mic_pid); |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.mbhc_reg, |
| 0x10, 0x10); |
| |
| /* Setup for low power removal detection */ |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_INT_CTL, 0x2, |
| 0x2); |
| } |
| |
| if (snd_soc_read(codec, WCD9XXX_A_CDC_MBHC_B1_CTL) & 0x4) { |
| /* called by interrupt */ |
| if (!is_clk_active(codec)) { |
| wcd9xxx_resmgr_enable_config_mode(mbhc->resmgr, 1); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, |
| 0x06, 0); |
| usleep_range(generic->t_shutdown_plug_rem, |
| generic->t_shutdown_plug_rem); |
| wcd9xxx_resmgr_enable_config_mode(mbhc->resmgr, 0); |
| } else |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, |
| 0x06, 0); |
| } |
| |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.int_rbias, 0x80, 0); |
| |
| /* If central bandgap disabled */ |
| if (!(snd_soc_read(codec, WCD9XXX_A_PIN_CTL_OE1) & 1)) { |
| snd_soc_update_bits(codec, WCD9XXX_A_PIN_CTL_OE1, 0x3, 0x3); |
| usleep_range(generic->t_bg_fast_settle, |
| generic->t_bg_fast_settle); |
| central_bias_enabled = 1; |
| } |
| |
| /* If LDO_H disabled */ |
| if (snd_soc_read(codec, WCD9XXX_A_PIN_CTL_OE0) & 0x80) { |
| snd_soc_update_bits(codec, WCD9XXX_A_PIN_CTL_OE0, 0x10, 0); |
| snd_soc_update_bits(codec, WCD9XXX_A_PIN_CTL_OE0, 0x80, 0x80); |
| usleep_range(generic->t_ldoh, generic->t_ldoh); |
| snd_soc_update_bits(codec, WCD9XXX_A_PIN_CTL_OE0, 0x80, 0); |
| |
| if (central_bias_enabled) |
| snd_soc_update_bits(codec, WCD9XXX_A_PIN_CTL_OE1, 0x1, |
| 0); |
| } |
| |
| if (mbhc->resmgr->reg_addr && mbhc->resmgr->reg_addr->micb_4_mbhc) |
| snd_soc_update_bits(codec, mbhc->resmgr->reg_addr->micb_4_mbhc, |
| 0x3, mbhc->mbhc_cfg->micbias); |
| |
| wcd9xxx_enable_irq(mbhc->resmgr->core_res, WCD9XXX_IRQ_MBHC_INSERTION); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_INT_CTL, 0x1, 0x1); |
| pr_debug("%s: leave\n", __func__); |
| |
| return 0; |
| } |
| |
| /* called under codec_resource_lock acquisition */ |
| static void wcd9xxx_find_plug_and_report(struct wcd9xxx_mbhc *mbhc, |
| enum wcd9xxx_mbhc_plug_type plug_type) |
| { |
| pr_debug("%s: enter current_plug(%d) new_plug(%d)\n", |
| __func__, mbhc->current_plug, plug_type); |
| |
| WCD9XXX_BCL_ASSERT_LOCKED(mbhc->resmgr); |
| |
| if (plug_type == PLUG_TYPE_HEADPHONE && |
| mbhc->current_plug == PLUG_TYPE_NONE) { |
| /* |
| * Nothing was reported previously |
| * report a headphone or unsupported |
| */ |
| wcd9xxx_report_plug(mbhc, 1, SND_JACK_HEADPHONE); |
| wcd9xxx_cleanup_hs_polling(mbhc); |
| } else if (plug_type == PLUG_TYPE_GND_MIC_SWAP) { |
| if (!mbhc->mbhc_cfg->detect_extn_cable) { |
| if (mbhc->current_plug == PLUG_TYPE_HEADSET) |
| wcd9xxx_report_plug(mbhc, 0, |
| SND_JACK_HEADSET); |
| else if (mbhc->current_plug == PLUG_TYPE_HEADPHONE) |
| wcd9xxx_report_plug(mbhc, 0, |
| SND_JACK_HEADPHONE); |
| } |
| wcd9xxx_report_plug(mbhc, 1, SND_JACK_UNSUPPORTED); |
| wcd9xxx_cleanup_hs_polling(mbhc); |
| } else if (plug_type == PLUG_TYPE_HEADSET) { |
| /* |
| * If Headphone was reported previously, this will |
| * only report the mic line |
| */ |
| wcd9xxx_report_plug(mbhc, 1, SND_JACK_HEADSET); |
| msleep(100); |
| |
| /* if PA is already on, switch micbias source to VDDIO */ |
| if (mbhc->event_state & |
| (1 << MBHC_EVENT_PA_HPHL | 1 << MBHC_EVENT_PA_HPHR)) |
| __wcd9xxx_switch_micbias(mbhc, 1, false, false); |
| wcd9xxx_start_hs_polling(mbhc); |
| } else if (plug_type == PLUG_TYPE_HIGH_HPH) { |
| if (mbhc->mbhc_cfg->detect_extn_cable) { |
| /* High impedance device found. Report as LINEOUT*/ |
| wcd9xxx_report_plug(mbhc, 1, SND_JACK_LINEOUT); |
| wcd9xxx_cleanup_hs_polling(mbhc); |
| pr_debug("%s: setup mic trigger for further detection\n", |
| __func__); |
| mbhc->lpi_enabled = true; |
| /* |
| * Do not enable HPHL trigger. If playback is active, |
| * it might lead to continuous false HPHL triggers |
| */ |
| wcd9xxx_enable_hs_detect(mbhc, 1, MBHC_USE_MB_TRIGGER, |
| false); |
| } else { |
| if (mbhc->current_plug == PLUG_TYPE_NONE) |
| wcd9xxx_report_plug(mbhc, 1, |
| SND_JACK_HEADPHONE); |
| wcd9xxx_cleanup_hs_polling(mbhc); |
| pr_debug("setup mic trigger for further detection\n"); |
| mbhc->lpi_enabled = true; |
| wcd9xxx_enable_hs_detect(mbhc, 1, MBHC_USE_MB_TRIGGER | |
| MBHC_USE_HPHL_TRIGGER, |
| false); |
| } |
| } else { |
| WARN(1, "Unexpected current plug_type %d, plug_type %d\n", |
| mbhc->current_plug, plug_type); |
| } |
| pr_debug("%s: leave\n", __func__); |
| } |
| |
| /* called under codec_resource_lock acquisition */ |
| static void wcd9xxx_mbhc_decide_swch_plug(struct wcd9xxx_mbhc *mbhc) |
| { |
| enum wcd9xxx_mbhc_plug_type plug_type; |
| bool current_source_enable; |
| |
| pr_debug("%s: enter\n", __func__); |
| |
| WCD9XXX_BCL_ASSERT_LOCKED(mbhc->resmgr); |
| current_source_enable = ((mbhc->mbhc_cfg->cs_enable_flags & |
| (1 << MBHC_CS_ENABLE_INSERTION)) != 0); |
| |
| if (current_source_enable) { |
| wcd9xxx_turn_onoff_current_source(mbhc, true, false); |
| plug_type = wcd9xxx_codec_cs_get_plug_type(mbhc, false); |
| wcd9xxx_turn_onoff_current_source(mbhc, false, false); |
| } else { |
| wcd9xxx_turn_onoff_override(mbhc, true); |
| plug_type = wcd9xxx_codec_get_plug_type(mbhc, true); |
| wcd9xxx_turn_onoff_override(mbhc, false); |
| } |
| |
| if (wcd9xxx_swch_level_remove(mbhc)) { |
| pr_debug("%s: Switch level is low when determining plug\n", |
| __func__); |
| return; |
| } |
| |
| if (plug_type == PLUG_TYPE_INVALID || |
| plug_type == PLUG_TYPE_GND_MIC_SWAP) { |
| wcd9xxx_cleanup_hs_polling(mbhc); |
| wcd9xxx_schedule_hs_detect_plug(mbhc, |
| &mbhc->correct_plug_swch); |
| } else if (plug_type == PLUG_TYPE_HEADPHONE) { |
| wcd9xxx_report_plug(mbhc, 1, SND_JACK_HEADPHONE); |
| wcd9xxx_cleanup_hs_polling(mbhc); |
| wcd9xxx_schedule_hs_detect_plug(mbhc, |
| &mbhc->correct_plug_swch); |
| } else if (plug_type == PLUG_TYPE_HIGH_HPH) { |
| wcd9xxx_cleanup_hs_polling(mbhc); |
| wcd9xxx_schedule_hs_detect_plug(mbhc, |
| &mbhc->correct_plug_swch); |
| } else { |
| pr_debug("%s: Valid plug found, determine plug type %d\n", |
| __func__, plug_type); |
| wcd9xxx_find_plug_and_report(mbhc, plug_type); |
| } |
| pr_debug("%s: leave\n", __func__); |
| } |
| |
| /* called under codec_resource_lock acquisition */ |
| static void wcd9xxx_mbhc_detect_plug_type(struct wcd9xxx_mbhc *mbhc) |
| { |
| pr_debug("%s: enter\n", __func__); |
| WCD9XXX_BCL_ASSERT_LOCKED(mbhc->resmgr); |
| |
| if (wcd9xxx_swch_level_remove(mbhc)) |
| pr_debug("%s: Switch level low when determining plug\n", |
| __func__); |
| else |
| wcd9xxx_mbhc_decide_swch_plug(mbhc); |
| pr_debug("%s: leave\n", __func__); |
| } |
| |
| /* called only from interrupt which is under codec_resource_lock acquisition */ |
| static void wcd9xxx_hs_insert_irq_swch(struct wcd9xxx_mbhc *mbhc, |
| bool is_removal) |
| { |
| if (!is_removal) { |
| pr_debug("%s: MIC trigger insertion interrupt\n", __func__); |
| |
| rmb(); |
| if (mbhc->lpi_enabled) |
| msleep(100); |
| |
| rmb(); |
| if (!mbhc->lpi_enabled) { |
| pr_debug("%s: lpi is disabled\n", __func__); |
| } else if (!wcd9xxx_swch_level_remove(mbhc)) { |
| pr_debug("%s: Valid insertion, detect plug type\n", |
| __func__); |
| wcd9xxx_mbhc_decide_swch_plug(mbhc); |
| } else { |
| pr_debug("%s: Invalid insertion stop plug detection\n", |
| __func__); |
| } |
| } else if (mbhc->mbhc_cfg->detect_extn_cable) { |
| pr_debug("%s: Removal\n", __func__); |
| if (!wcd9xxx_swch_level_remove(mbhc)) { |
| /* |
| * Switch indicates, something is still inserted. |
| * This could be extension cable i.e. headset is |
| * removed from extension cable. |
| */ |
| /* cancel detect plug */ |
| wcd9xxx_cancel_hs_detect_plug(mbhc, |
| &mbhc->correct_plug_swch); |
| wcd9xxx_mbhc_decide_swch_plug(mbhc); |
| } |
| } else { |
| pr_err("%s: Switch IRQ used, invalid MBHC Removal\n", __func__); |
| } |
| } |
| |
| static bool is_valid_mic_voltage(struct wcd9xxx_mbhc *mbhc, s32 mic_mv, |
| bool cs_enable) |
| { |
| const struct wcd9xxx_mbhc_plug_type_cfg *plug_type = |
| WCD9XXX_MBHC_CAL_PLUG_TYPE_PTR(mbhc->mbhc_cfg->calibration); |
| const s16 v_hs_max = wcd9xxx_get_current_v_hs_max(mbhc); |
| |
| if (cs_enable) |
| return ((mic_mv > WCD9XXX_V_CS_NO_MIC) && |
| (mic_mv < WCD9XXX_V_CS_HS_MAX)) ? true : false; |
| else |
| return (!(mic_mv > WCD9XXX_MEAS_INVALD_RANGE_LOW_MV && |
| mic_mv < WCD9XXX_MEAS_INVALD_RANGE_HIGH_MV) && |
| (mic_mv > plug_type->v_no_mic) && |
| (mic_mv < v_hs_max)) ? true : false; |
| } |
| |
| /* |
| * called under codec_resource_lock acquisition |
| * returns true if mic voltage range is back to normal insertion |
| * returns false either if timedout or removed |
| */ |
| static bool wcd9xxx_hs_remove_settle(struct wcd9xxx_mbhc *mbhc) |
| { |
| int i; |
| bool timedout, settled = false; |
| s32 mic_mv[NUM_DCE_PLUG_DETECT]; |
| short mb_v[NUM_DCE_PLUG_DETECT]; |
| unsigned long retry = 0, timeout; |
| bool cs_enable; |
| |
| cs_enable = ((mbhc->mbhc_cfg->cs_enable_flags & |
| (1 << MBHC_CS_ENABLE_REMOVAL)) != 0); |
| |
| if (cs_enable) |
| wcd9xxx_turn_onoff_current_source(mbhc, true, false); |
| |
| timeout = jiffies + msecs_to_jiffies(HS_DETECT_PLUG_TIME_MS); |
| while (!(timedout = time_after(jiffies, timeout))) { |
| retry++; |
| if (wcd9xxx_swch_level_remove(mbhc)) { |
| pr_debug("%s: Switch indicates removal\n", __func__); |
| break; |
| } |
| |
| if (retry > 1) |
| msleep(250); |
| else |
| msleep(50); |
| |
| if (wcd9xxx_swch_level_remove(mbhc)) { |
| pr_debug("%s: Switch indicates removal\n", __func__); |
| break; |
| } |
| |
| if (cs_enable) { |
| for (i = 0; i < NUM_DCE_PLUG_DETECT; i++) { |
| mb_v[i] = __wcd9xxx_codec_sta_dce(mbhc, 1, |
| true, true); |
| mic_mv[i] = __wcd9xxx_codec_sta_dce_v(mbhc, |
| true, |
| mb_v[i], |
| mbhc->mbhc_data.dce_nsc_cs_z, |
| (u32)VDDIO_MICBIAS_MV); |
| pr_debug("%s : DCE run %lu, mic_mv = %d(%x)\n", |
| __func__, retry, mic_mv[i], mb_v[i]); |
| } |
| } else { |
| for (i = 0; i < NUM_DCE_PLUG_DETECT; i++) { |
| mb_v[i] = wcd9xxx_codec_sta_dce(mbhc, 1, |
| true); |
| mic_mv[i] = wcd9xxx_codec_sta_dce_v(mbhc, 1, |
| mb_v[i]); |
| pr_debug("%s : DCE run %lu, mic_mv = %d(%x)\n", |
| __func__, retry, mic_mv[i], |
| mb_v[i]); |
| } |
| } |
| |
| if (wcd9xxx_swch_level_remove(mbhc)) { |
| pr_debug("%s: Switcn indicates removal\n", __func__); |
| break; |
| } |
| |
| if (mbhc->current_plug == PLUG_TYPE_NONE) { |
| pr_debug("%s : headset/headphone is removed\n", |
| __func__); |
| break; |
| } |
| |
| for (i = 0; i < NUM_DCE_PLUG_DETECT; i++) |
| if (!is_valid_mic_voltage(mbhc, mic_mv[i], cs_enable)) |
| break; |
| |
| if (i == NUM_DCE_PLUG_DETECT) { |
| pr_debug("%s: MIC voltage settled\n", __func__); |
| settled = true; |
| msleep(200); |
| break; |
| } |
| } |
| |
| if (cs_enable) |
| wcd9xxx_turn_onoff_current_source(mbhc, false, false); |
| |
| if (timedout) |
| pr_debug("%s: Microphone did not settle in %d seconds\n", |
| __func__, HS_DETECT_PLUG_TIME_MS); |
| return settled; |
| } |
| |
| /* called only from interrupt which is under codec_resource_lock acquisition */ |
| static void wcd9xxx_hs_remove_irq_swch(struct wcd9xxx_mbhc *mbhc) |
| { |
| pr_debug("%s: enter\n", __func__); |
| if (wcd9xxx_hs_remove_settle(mbhc)) |
| wcd9xxx_start_hs_polling(mbhc); |
| pr_debug("%s: leave\n", __func__); |
| } |
| |
| /* called only from interrupt which is under codec_resource_lock acquisition */ |
| static void wcd9xxx_hs_remove_irq_noswch(struct wcd9xxx_mbhc *mbhc) |
| { |
| s16 dce, dcez; |
| unsigned long timeout; |
| bool removed = true; |
| struct snd_soc_codec *codec = mbhc->codec; |
| const struct wcd9xxx_mbhc_general_cfg *generic = |
| WCD9XXX_MBHC_CAL_GENERAL_PTR(mbhc->mbhc_cfg->calibration); |
| bool cs_enable; |
| s16 cur_v_ins_h; |
| u32 mb_mv; |
| |
| pr_debug("%s: enter\n", __func__); |
| if (mbhc->current_plug != PLUG_TYPE_HEADSET) { |
| pr_debug("%s(): Headset is not inserted, ignore removal\n", |
| __func__); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, |
| 0x08, 0x08); |
| return; |
| } |
| |
| usleep_range(generic->t_shutdown_plug_rem, |
| generic->t_shutdown_plug_rem); |
| |
| /* If micbias is enabled, don't enable current source */ |
| cs_enable = (((mbhc->mbhc_cfg->cs_enable_flags & |
| (1 << MBHC_CS_ENABLE_REMOVAL)) != 0) && |
| (!(snd_soc_read(codec, |
| mbhc->mbhc_bias_regs.ctl_reg) & 0x80))); |
| if (cs_enable) |
| wcd9xxx_turn_onoff_current_source(mbhc, true, false); |
| |
| timeout = jiffies + msecs_to_jiffies(FAKE_REMOVAL_MIN_PERIOD_MS); |
| do { |
| if (cs_enable) { |
| dce = __wcd9xxx_codec_sta_dce(mbhc, 1, true, true); |
| dcez = mbhc->mbhc_data.dce_nsc_cs_z; |
| mb_mv = VDDIO_MICBIAS_MV; |
| } else { |
| dce = wcd9xxx_codec_sta_dce(mbhc, 1, true); |
| dcez = mbhc->mbhc_data.dce_z; |
| mb_mv = mbhc->mbhc_data.micb_mv; |
| } |
| |
| pr_debug("%s: DCE 0x%x,%d\n", __func__, dce, |
| __wcd9xxx_codec_sta_dce_v(mbhc, true, dce, |
| dcez, mb_mv)); |
| |
| cur_v_ins_h = cs_enable ? (s16) mbhc->mbhc_data.v_cs_ins_h : |
| (wcd9xxx_get_current_v(mbhc, |
| WCD9XXX_CURRENT_V_INS_H)); |
| |
| if (dce < cur_v_ins_h) { |
| removed = false; |
| break; |
| } |
| } while (!time_after(jiffies, timeout)); |
| pr_debug("%s: headset %sactually removed\n", __func__, |
| removed ? "" : "not "); |
| |
| if (cs_enable) |
| wcd9xxx_turn_onoff_current_source(mbhc, false, false); |
| |
| if (removed) { |
| if (mbhc->mbhc_cfg->detect_extn_cable) { |
| if (!wcd9xxx_swch_level_remove(mbhc)) { |
| /* |
| * extension cable is still plugged in |
| * report it as LINEOUT device |
| */ |
| wcd9xxx_report_plug(mbhc, 1, SND_JACK_LINEOUT); |
| wcd9xxx_cleanup_hs_polling(mbhc); |
| wcd9xxx_enable_hs_detect(mbhc, 1, |
| MBHC_USE_MB_TRIGGER, |
| false); |
| } |
| } else { |
| /* Cancel possibly running hs_detect_work */ |
| wcd9xxx_cancel_hs_detect_plug(mbhc, |
| &mbhc->correct_plug_noswch); |
| /* |
| * If this removal is not false, first check the micbias |
| * switch status and switch it to LDOH if it is already |
| * switched to VDDIO. |
| */ |
| wcd9xxx_switch_micbias(mbhc, 0); |
| |
| wcd9xxx_report_plug(mbhc, 0, SND_JACK_HEADSET); |
| wcd9xxx_cleanup_hs_polling(mbhc); |
| wcd9xxx_enable_hs_detect(mbhc, 1, MBHC_USE_MB_TRIGGER | |
| MBHC_USE_HPHL_TRIGGER, |
| true); |
| } |
| } else { |
| wcd9xxx_start_hs_polling(mbhc); |
| } |
| pr_debug("%s: leave\n", __func__); |
| } |
| |
| /* called only from interrupt which is under codec_resource_lock acquisition */ |
| static void wcd9xxx_hs_insert_irq_extn(struct wcd9xxx_mbhc *mbhc, |
| bool is_mb_trigger) |
| { |
| /* Cancel possibly running hs_detect_work */ |
| wcd9xxx_cancel_hs_detect_plug(mbhc, &mbhc->correct_plug_swch); |
| |
| if (is_mb_trigger) { |
| pr_debug("%s: Waiting for Headphone left trigger\n", __func__); |
| wcd9xxx_enable_hs_detect(mbhc, 1, MBHC_USE_HPHL_TRIGGER, false); |
| } else { |
| pr_debug("%s: HPHL trigger received, detecting plug type\n", |
| __func__); |
| wcd9xxx_mbhc_detect_plug_type(mbhc); |
| } |
| } |
| |
| static irqreturn_t wcd9xxx_hs_remove_irq(int irq, void *data) |
| { |
| struct wcd9xxx_mbhc *mbhc = data; |
| |
| pr_debug("%s: enter, removal interrupt\n", __func__); |
| WCD9XXX_BCL_LOCK(mbhc->resmgr); |
| /* |
| * While we don't know whether MIC is there or not, let the resmgr know |
| * so micbias can be disabled temporarily |
| */ |
| if (mbhc->current_plug == PLUG_TYPE_HEADSET) { |
| wcd9xxx_resmgr_cond_update_cond(mbhc->resmgr, |
| WCD9XXX_COND_HPH_MIC, false); |
| wcd9xxx_resmgr_cond_update_cond(mbhc->resmgr, |
| WCD9XXX_COND_HPH, false); |
| } else if (mbhc->current_plug == PLUG_TYPE_HEADPHONE) { |
| wcd9xxx_resmgr_cond_update_cond(mbhc->resmgr, |
| WCD9XXX_COND_HPH, false); |
| } |
| |
| if (mbhc->mbhc_cfg->detect_extn_cable && |
| !wcd9xxx_swch_level_remove(mbhc)) |
| wcd9xxx_hs_remove_irq_noswch(mbhc); |
| else |
| wcd9xxx_hs_remove_irq_swch(mbhc); |
| |
| if (mbhc->current_plug == PLUG_TYPE_HEADSET) { |
| wcd9xxx_resmgr_cond_update_cond(mbhc->resmgr, |
| WCD9XXX_COND_HPH, true); |
| wcd9xxx_resmgr_cond_update_cond(mbhc->resmgr, |
| WCD9XXX_COND_HPH_MIC, true); |
| } else if (mbhc->current_plug == PLUG_TYPE_HEADPHONE) { |
| wcd9xxx_resmgr_cond_update_cond(mbhc->resmgr, |
| WCD9XXX_COND_HPH, true); |
| } |
| WCD9XXX_BCL_UNLOCK(mbhc->resmgr); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t wcd9xxx_hs_insert_irq(int irq, void *data) |
| { |
| bool is_mb_trigger, is_removal; |
| struct wcd9xxx_mbhc *mbhc = data; |
| struct snd_soc_codec *codec = mbhc->codec; |
| |
| pr_debug("%s: enter\n", __func__); |
| WCD9XXX_BCL_LOCK(mbhc->resmgr); |
| wcd9xxx_disable_irq(mbhc->resmgr->core_res, WCD9XXX_IRQ_MBHC_INSERTION); |
| |
| is_mb_trigger = !!(snd_soc_read(codec, mbhc->mbhc_bias_regs.mbhc_reg) & |
| 0x10); |
| is_removal = !!(snd_soc_read(codec, WCD9XXX_A_CDC_MBHC_INT_CTL) & 0x02); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_INT_CTL, 0x03, 0x00); |
| |
| /* Turn off both HPH and MIC line schmitt triggers */ |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.mbhc_reg, 0x90, 0x00); |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_HPH, 0x13, 0x00); |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.ctl_reg, 0x01, 0x00); |
| |
| if (mbhc->mbhc_cfg->detect_extn_cable && |
| mbhc->current_plug == PLUG_TYPE_HIGH_HPH) |
| wcd9xxx_hs_insert_irq_extn(mbhc, is_mb_trigger); |
| else |
| wcd9xxx_hs_insert_irq_swch(mbhc, is_removal); |
| |
| WCD9XXX_BCL_UNLOCK(mbhc->resmgr); |
| return IRQ_HANDLED; |
| } |
| |
| static void wcd9xxx_btn_lpress_fn(struct work_struct *work) |
| { |
| struct delayed_work *dwork; |
| short bias_value; |
| int dce_mv, sta_mv; |
| struct wcd9xxx_mbhc *mbhc; |
| |
| pr_debug("%s:\n", __func__); |
| |
| dwork = to_delayed_work(work); |
| mbhc = container_of(dwork, struct wcd9xxx_mbhc, mbhc_btn_dwork); |
| |
| bias_value = wcd9xxx_read_sta_result(mbhc->codec); |
| sta_mv = wcd9xxx_codec_sta_dce_v(mbhc, 0, bias_value); |
| |
| bias_value = wcd9xxx_read_dce_result(mbhc->codec); |
| dce_mv = wcd9xxx_codec_sta_dce_v(mbhc, 1, bias_value); |
| pr_debug("%s: STA: %d, DCE: %d\n", __func__, sta_mv, dce_mv); |
| |
| pr_debug("%s: Reporting long button press event\n", __func__); |
| wcd9xxx_jack_report(mbhc, &mbhc->button_jack, mbhc->buttons_pressed, |
| mbhc->buttons_pressed); |
| |
| pr_debug("%s: leave\n", __func__); |
| wcd9xxx_unlock_sleep(mbhc->resmgr->core_res); |
| } |
| |
| static void wcd9xxx_mbhc_insert_work(struct work_struct *work) |
| { |
| struct delayed_work *dwork; |
| struct wcd9xxx_mbhc *mbhc; |
| struct snd_soc_codec *codec; |
| struct wcd9xxx_core_resource *core_res; |
| |
| dwork = to_delayed_work(work); |
| mbhc = container_of(dwork, struct wcd9xxx_mbhc, mbhc_insert_dwork); |
| codec = mbhc->codec; |
| core_res = mbhc->resmgr->core_res; |
| |
| pr_debug("%s:\n", __func__); |
| |
| /* Turn off both HPH and MIC line schmitt triggers */ |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.mbhc_reg, 0x90, 0x00); |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_HPH, 0x13, 0x00); |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.ctl_reg, 0x01, 0x00); |
| wcd9xxx_disable_irq_sync(core_res, WCD9XXX_IRQ_MBHC_INSERTION); |
| wcd9xxx_mbhc_detect_plug_type(mbhc); |
| wcd9xxx_unlock_sleep(core_res); |
| } |
| |
| static bool wcd9xxx_mbhc_fw_validate(const struct firmware *fw) |
| { |
| u32 cfg_offset; |
| struct wcd9xxx_mbhc_imped_detect_cfg *imped_cfg; |
| struct wcd9xxx_mbhc_btn_detect_cfg *btn_cfg; |
| |
| if (fw->size < WCD9XXX_MBHC_CAL_MIN_SIZE) |
| return false; |
| |
| /* |
| * Previous check guarantees that there is enough fw data up |
| * to num_btn |
| */ |
| btn_cfg = WCD9XXX_MBHC_CAL_BTN_DET_PTR(fw->data); |
| cfg_offset = (u32) ((void *) btn_cfg - (void *) fw->data); |
| if (fw->size < (cfg_offset + WCD9XXX_MBHC_CAL_BTN_SZ(btn_cfg))) |
| return false; |
| |
| /* |
| * Previous check guarantees that there is enough fw data up |
| * to start of impedance detection configuration |
| */ |
| imped_cfg = WCD9XXX_MBHC_CAL_IMPED_DET_PTR(fw->data); |
| cfg_offset = (u32) ((void *) imped_cfg - (void *) fw->data); |
| |
| if (fw->size < (cfg_offset + WCD9XXX_MBHC_CAL_IMPED_MIN_SZ)) |
| return false; |
| |
| if (fw->size < (cfg_offset + WCD9XXX_MBHC_CAL_IMPED_SZ(imped_cfg))) |
| return false; |
| |
| return true; |
| } |
| |
| static u16 wcd9xxx_codec_v_sta_dce(struct wcd9xxx_mbhc *mbhc, |
| enum meas_type dce, s16 vin_mv, |
| bool cs_enable) |
| { |
| s16 diff, zero; |
| u32 mb_mv, in; |
| u16 value; |
| s16 dce_z; |
| |
| mb_mv = mbhc->mbhc_data.micb_mv; |
| dce_z = mbhc->mbhc_data.dce_z; |
| |
| if (mb_mv == 0) { |
| pr_err("%s: Mic Bias voltage is set to zero\n", __func__); |
| return -EINVAL; |
| } |
| if (cs_enable) { |
| mb_mv = VDDIO_MICBIAS_MV; |
| dce_z = mbhc->mbhc_data.dce_nsc_cs_z; |
| } |
| |
| if (dce) { |
| diff = (mbhc->mbhc_data.dce_mb) - (dce_z); |
| zero = (dce_z); |
| } else { |
| diff = (mbhc->mbhc_data.sta_mb) - (mbhc->mbhc_data.sta_z); |
| zero = (mbhc->mbhc_data.sta_z); |
| } |
| in = (u32) diff * vin_mv; |
| |
| value = (u16) (in / mb_mv) + zero; |
| return value; |
| } |
| |
| static void wcd9xxx_mbhc_calc_thres(struct wcd9xxx_mbhc *mbhc) |
| { |
| struct snd_soc_codec *codec; |
| s16 adj_v_hs_max; |
| s16 btn_mv = 0, btn_mv_sta[MBHC_V_IDX_NUM], btn_mv_dce[MBHC_V_IDX_NUM]; |
| struct wcd9xxx_mbhc_btn_detect_cfg *btn_det; |
| struct wcd9xxx_mbhc_plug_type_cfg *plug_type; |
| u16 *btn_high; |
| int i; |
| |
| pr_debug("%s: enter\n", __func__); |
| codec = mbhc->codec; |
| btn_det = WCD9XXX_MBHC_CAL_BTN_DET_PTR(mbhc->mbhc_cfg->calibration); |
| plug_type = WCD9XXX_MBHC_CAL_PLUG_TYPE_PTR(mbhc->mbhc_cfg->calibration); |
| |
| mbhc->mbhc_data.v_ins_hu[MBHC_V_IDX_CFILT] = |
| wcd9xxx_codec_v_sta_dce(mbhc, STA, plug_type->v_hs_max, false); |
| mbhc->mbhc_data.v_ins_h[MBHC_V_IDX_CFILT] = |
| wcd9xxx_codec_v_sta_dce(mbhc, DCE, plug_type->v_hs_max, false); |
| |
| mbhc->mbhc_data.v_inval_ins_low = FAKE_INS_LOW; |
| mbhc->mbhc_data.v_inval_ins_high = FAKE_INS_HIGH; |
| |
| if (mbhc->mbhc_data.micb_mv != VDDIO_MICBIAS_MV) { |
| adj_v_hs_max = scale_v_micb_vddio(mbhc, plug_type->v_hs_max, |
| true); |
| mbhc->mbhc_data.v_ins_hu[MBHC_V_IDX_VDDIO] = |
| wcd9xxx_codec_v_sta_dce(mbhc, STA, adj_v_hs_max, false); |
| mbhc->mbhc_data.v_ins_h[MBHC_V_IDX_VDDIO] = |
| wcd9xxx_codec_v_sta_dce(mbhc, DCE, adj_v_hs_max, false); |
| mbhc->mbhc_data.v_inval_ins_low = |
| scale_v_micb_vddio(mbhc, mbhc->mbhc_data.v_inval_ins_low, |
| false); |
| mbhc->mbhc_data.v_inval_ins_high = |
| scale_v_micb_vddio(mbhc, mbhc->mbhc_data.v_inval_ins_high, |
| false); |
| } |
| mbhc->mbhc_data.v_cs_ins_h = wcd9xxx_codec_v_sta_dce(mbhc, DCE, |
| WCD9XXX_V_CS_HS_MAX, |
| true); |
| pr_debug("%s: v_ins_h for current source: 0x%x\n", __func__, |
| mbhc->mbhc_data.v_cs_ins_h); |
| |
| btn_high = wcd9xxx_mbhc_cal_btn_det_mp(btn_det, |
| MBHC_BTN_DET_V_BTN_HIGH); |
| for (i = 0; i < btn_det->num_btn; i++) |
| btn_mv = btn_high[i] > btn_mv ? btn_high[i] : btn_mv; |
| |
| btn_mv_sta[MBHC_V_IDX_CFILT] = btn_mv + btn_det->v_btn_press_delta_sta; |
| btn_mv_dce[MBHC_V_IDX_CFILT] = btn_mv + btn_det->v_btn_press_delta_cic; |
| btn_mv_sta[MBHC_V_IDX_VDDIO] = |
| scale_v_micb_vddio(mbhc, btn_mv_sta[MBHC_V_IDX_CFILT], true); |
| btn_mv_dce[MBHC_V_IDX_VDDIO] = |
| scale_v_micb_vddio(mbhc, btn_mv_dce[MBHC_V_IDX_CFILT], true); |
| |
| mbhc->mbhc_data.v_b1_hu[MBHC_V_IDX_CFILT] = |
| wcd9xxx_codec_v_sta_dce(mbhc, STA, btn_mv_sta[MBHC_V_IDX_CFILT], |
| false); |
| mbhc->mbhc_data.v_b1_h[MBHC_V_IDX_CFILT] = |
| wcd9xxx_codec_v_sta_dce(mbhc, DCE, btn_mv_dce[MBHC_V_IDX_CFILT], |
| false); |
| mbhc->mbhc_data.v_b1_hu[MBHC_V_IDX_VDDIO] = |
| wcd9xxx_codec_v_sta_dce(mbhc, STA, btn_mv_sta[MBHC_V_IDX_VDDIO], |
| false); |
| mbhc->mbhc_data.v_b1_h[MBHC_V_IDX_VDDIO] = |
| wcd9xxx_codec_v_sta_dce(mbhc, DCE, btn_mv_dce[MBHC_V_IDX_VDDIO], |
| false); |
| |
| mbhc->mbhc_data.v_brh[MBHC_V_IDX_CFILT] = |
| mbhc->mbhc_data.v_b1_h[MBHC_V_IDX_CFILT]; |
| mbhc->mbhc_data.v_brh[MBHC_V_IDX_VDDIO] = |
| mbhc->mbhc_data.v_b1_h[MBHC_V_IDX_VDDIO]; |
| |
| mbhc->mbhc_data.v_brl = BUTTON_MIN; |
| |
| mbhc->mbhc_data.v_no_mic = |
| wcd9xxx_codec_v_sta_dce(mbhc, STA, plug_type->v_no_mic, false); |
| pr_debug("%s: leave\n", __func__); |
| } |
| |
| static void wcd9xxx_onoff_ext_mclk(struct wcd9xxx_mbhc *mbhc, bool on) |
| { |
| /* |
| * XXX: {codec}_mclk_enable holds WCD9XXX_BCL_LOCK, |
| * therefore wcd9xxx_onoff_ext_mclk caller SHOULDN'T hold |
| * WCD9XXX_BCL_LOCK when it calls wcd9xxx_onoff_ext_mclk() |
| */ |
| mbhc->mbhc_cfg->mclk_cb_fn(mbhc->codec, on, false); |
| } |
| |
| /* |
| * Mic Bias Enable Decision |
| * Return true if high_hph_cnt is a power of 2 (!= 2) |
| * otherwise return false |
| */ |
| static bool wcd9xxx_mbhc_enable_mb_decision(int high_hph_cnt) |
| { |
| return (high_hph_cnt > 2) && !(high_hph_cnt & (high_hph_cnt - 1)); |
| } |
| |
| static void wcd9xxx_correct_swch_plug(struct work_struct *work) |
| { |
| struct wcd9xxx_mbhc *mbhc; |
| struct snd_soc_codec *codec; |
| enum wcd9xxx_mbhc_plug_type plug_type = PLUG_TYPE_INVALID; |
| unsigned long timeout; |
| int retry = 0, pt_gnd_mic_swap_cnt = 0; |
| int highhph_cnt = 0; |
| bool correction = false; |
| bool current_source_enable; |
| bool wrk_complete = true, highhph = false; |
| |
| pr_debug("%s: enter\n", __func__); |
| |
| mbhc = container_of(work, struct wcd9xxx_mbhc, correct_plug_swch); |
| codec = mbhc->codec; |
| current_source_enable = ((mbhc->mbhc_cfg->cs_enable_flags & |
| (1 << MBHC_CS_ENABLE_POLLING)) != 0); |
| |
| wcd9xxx_onoff_ext_mclk(mbhc, true); |
| |
| /* |
| * Keep override on during entire plug type correction work. |
| * |
| * This is okay under the assumption that any switch irqs which use |
| * MBHC block cancel and sync this work so override is off again |
| * prior to switch interrupt handler's MBHC block usage. |
| * Also while this correction work is running, we can guarantee |
| * DAPM doesn't use any MBHC block as this work only runs with |
| * headphone detection. |
| */ |
| if (current_source_enable) |
| wcd9xxx_turn_onoff_current_source(mbhc, true, |
| false); |
| else |
| wcd9xxx_turn_onoff_override(mbhc, true); |
| |
| timeout = jiffies + msecs_to_jiffies(HS_DETECT_PLUG_TIME_MS); |
| while (!time_after(jiffies, timeout)) { |
| ++retry; |
| rmb(); |
| if (mbhc->hs_detect_work_stop) { |
| wrk_complete = false; |
| pr_debug("%s: stop requested\n", __func__); |
| break; |
| } |
| |
| msleep(HS_DETECT_PLUG_INERVAL_MS); |
| if (wcd9xxx_swch_level_remove(mbhc)) { |
| wrk_complete = false; |
| pr_debug("%s: Switch level is low\n", __func__); |
| break; |
| } |
| |
| /* can race with removal interrupt */ |
| WCD9XXX_BCL_LOCK(mbhc->resmgr); |
| if (current_source_enable) |
| plug_type = wcd9xxx_codec_cs_get_plug_type(mbhc, |
| highhph); |
| else |
| plug_type = wcd9xxx_codec_get_plug_type(mbhc, true); |
| WCD9XXX_BCL_UNLOCK(mbhc->resmgr); |
| |
| pr_debug("%s: attempt(%d) current_plug(%d) new_plug(%d)\n", |
| __func__, retry, mbhc->current_plug, plug_type); |
| |
| highhph_cnt = (plug_type == PLUG_TYPE_HIGH_HPH) ? |
| (highhph_cnt + 1) : |
| 0; |
| highhph = wcd9xxx_mbhc_enable_mb_decision(highhph_cnt); |
| if (plug_type == PLUG_TYPE_INVALID) { |
| pr_debug("Invalid plug in attempt # %d\n", retry); |
| if (!mbhc->mbhc_cfg->detect_extn_cable && |
| retry == NUM_ATTEMPTS_TO_REPORT && |
| mbhc->current_plug == PLUG_TYPE_NONE) { |
| wcd9xxx_report_plug(mbhc, 1, |
| SND_JACK_HEADPHONE); |
| } |
| } else if (plug_type == PLUG_TYPE_HEADPHONE) { |
| pr_debug("Good headphone detected, continue polling\n"); |
| if (mbhc->mbhc_cfg->detect_extn_cable) { |
| if (mbhc->current_plug != plug_type) |
| wcd9xxx_report_plug(mbhc, 1, |
| SND_JACK_HEADPHONE); |
| } else if (mbhc->current_plug == PLUG_TYPE_NONE) { |
| wcd9xxx_report_plug(mbhc, 1, |
| SND_JACK_HEADPHONE); |
| } |
| } else if (plug_type == PLUG_TYPE_HIGH_HPH) { |
| pr_debug("%s: High HPH detected, continue polling\n", |
| __func__); |
| } else { |
| if (plug_type == PLUG_TYPE_GND_MIC_SWAP) { |
| pt_gnd_mic_swap_cnt++; |
| if (pt_gnd_mic_swap_cnt < |
| GND_MIC_SWAP_THRESHOLD) |
| continue; |
| else if (pt_gnd_mic_swap_cnt > |
| GND_MIC_SWAP_THRESHOLD) { |
| /* |
| * This is due to GND/MIC switch didn't |
| * work, Report unsupported plug |
| */ |
| } else if (mbhc->mbhc_cfg->swap_gnd_mic) { |
| /* |
| * if switch is toggled, check again, |
| * otherwise report unsupported plug |
| */ |
| if (mbhc->mbhc_cfg->swap_gnd_mic(codec)) |
| continue; |
| } |
| } else |
| pt_gnd_mic_swap_cnt = 0; |
| |
| WCD9XXX_BCL_LOCK(mbhc->resmgr); |
| /* Turn off override/current source */ |
| if (current_source_enable) |
| wcd9xxx_turn_onoff_current_source(mbhc, false, |
| false); |
| else |
| wcd9xxx_turn_onoff_override(mbhc, false); |
| /* |
| * The valid plug also includes PLUG_TYPE_GND_MIC_SWAP |
| */ |
| wcd9xxx_find_plug_and_report(mbhc, plug_type); |
| WCD9XXX_BCL_UNLOCK(mbhc->resmgr); |
| pr_debug("Attempt %d found correct plug %d\n", retry, |
| plug_type); |
| correction = true; |
| break; |
| } |
| } |
| |
| highhph = false; |
| if (wrk_complete && plug_type == PLUG_TYPE_HIGH_HPH) { |
| pr_debug("%s: polling is done, still HPH, so enabling MIC trigger\n", |
| __func__); |
| WCD9XXX_BCL_LOCK(mbhc->resmgr); |
| wcd9xxx_find_plug_and_report(mbhc, plug_type); |
| highhph = true; |
| WCD9XXX_BCL_UNLOCK(mbhc->resmgr); |
| } |
| |
| if (!correction && current_source_enable) |
| wcd9xxx_turn_onoff_current_source(mbhc, false, highhph); |
| else if (!correction) |
| wcd9xxx_turn_onoff_override(mbhc, false); |
| |
| wcd9xxx_onoff_ext_mclk(mbhc, false); |
| |
| if (mbhc->mbhc_cfg->detect_extn_cable) { |
| WCD9XXX_BCL_LOCK(mbhc->resmgr); |
| if ((mbhc->current_plug == PLUG_TYPE_HEADPHONE && |
| wrk_complete) || |
| mbhc->current_plug == PLUG_TYPE_GND_MIC_SWAP || |
| mbhc->current_plug == PLUG_TYPE_INVALID || |
| (plug_type == PLUG_TYPE_INVALID && wrk_complete)) { |
| /* Enable removal detection */ |
| wcd9xxx_cleanup_hs_polling(mbhc); |
| wcd9xxx_enable_hs_detect(mbhc, 0, 0, false); |
| } |
| WCD9XXX_BCL_UNLOCK(mbhc->resmgr); |
| } |
| pr_debug("%s: leave current_plug(%d)\n", __func__, mbhc->current_plug); |
| /* unlock sleep */ |
| wcd9xxx_unlock_sleep(mbhc->resmgr->core_res); |
| } |
| |
| static void wcd9xxx_swch_irq_handler(struct wcd9xxx_mbhc *mbhc) |
| { |
| bool insert; |
| bool is_removed = false; |
| struct snd_soc_codec *codec = mbhc->codec; |
| |
| pr_debug("%s: enter\n", __func__); |
| |
| mbhc->in_swch_irq_handler = true; |
| /* Wait here for debounce time */ |
| usleep_range(SWCH_IRQ_DEBOUNCE_TIME_US, SWCH_IRQ_DEBOUNCE_TIME_US); |
| |
| WCD9XXX_BCL_LOCK(mbhc->resmgr); |
| |
| /* cancel pending button press */ |
| if (wcd9xxx_cancel_btn_work(mbhc)) |
| pr_debug("%s: button press is canceled\n", __func__); |
| |
| insert = !wcd9xxx_swch_level_remove(mbhc); |
| pr_debug("%s: Current plug type %d, insert %d\n", __func__, |
| mbhc->current_plug, insert); |
| if ((mbhc->current_plug == PLUG_TYPE_NONE) && insert) { |
| mbhc->lpi_enabled = false; |
| wmb(); |
| |
| /* cancel detect plug */ |
| wcd9xxx_cancel_hs_detect_plug(mbhc, |
| &mbhc->correct_plug_swch); |
| |
| /* Disable Mic Bias pull down and HPH Switch to GND */ |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.ctl_reg, 0x01, |
| 0x00); |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_HPH, 0x01, 0x00); |
| wcd9xxx_mbhc_detect_plug_type(mbhc); |
| } else if ((mbhc->current_plug != PLUG_TYPE_NONE) && !insert) { |
| mbhc->lpi_enabled = false; |
| wmb(); |
| |
| /* cancel detect plug */ |
| wcd9xxx_cancel_hs_detect_plug(mbhc, |
| &mbhc->correct_plug_swch); |
| |
| if (mbhc->current_plug == PLUG_TYPE_HEADPHONE) { |
| wcd9xxx_report_plug(mbhc, 0, SND_JACK_HEADPHONE); |
| is_removed = true; |
| } else if (mbhc->current_plug == PLUG_TYPE_GND_MIC_SWAP) { |
| wcd9xxx_report_plug(mbhc, 0, SND_JACK_UNSUPPORTED); |
| is_removed = true; |
| } else if (mbhc->current_plug == PLUG_TYPE_HEADSET) { |
| wcd9xxx_pause_hs_polling(mbhc); |
| wcd9xxx_cleanup_hs_polling(mbhc); |
| wcd9xxx_report_plug(mbhc, 0, SND_JACK_HEADSET); |
| is_removed = true; |
| } else if (mbhc->current_plug == PLUG_TYPE_HIGH_HPH) { |
| wcd9xxx_report_plug(mbhc, 0, SND_JACK_LINEOUT); |
| is_removed = true; |
| } |
| |
| if (is_removed) { |
| /* Enable Mic Bias pull down and HPH Switch to GND */ |
| snd_soc_update_bits(codec, |
| mbhc->mbhc_bias_regs.ctl_reg, 0x01, |
| 0x01); |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_HPH, 0x01, |
| 0x01); |
| /* Make sure mic trigger is turned off */ |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.ctl_reg, |
| 0x01, 0x01); |
| snd_soc_update_bits(codec, |
| mbhc->mbhc_bias_regs.mbhc_reg, |
| 0x90, 0x00); |
| /* Reset MBHC State Machine */ |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, |
| 0x08, 0x08); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, |
| 0x08, 0x00); |
| /* Turn off override */ |
| wcd9xxx_turn_onoff_override(mbhc, false); |
| } |
| } |
| |
| mbhc->in_swch_irq_handler = false; |
| WCD9XXX_BCL_UNLOCK(mbhc->resmgr); |
| pr_debug("%s: leave\n", __func__); |
| } |
| |
| static irqreturn_t wcd9xxx_mech_plug_detect_irq(int irq, void *data) |
| { |
| int r = IRQ_HANDLED; |
| struct wcd9xxx_mbhc *mbhc = data; |
| |
| pr_debug("%s: enter\n", __func__); |
| if (unlikely(wcd9xxx_lock_sleep(mbhc->resmgr->core_res) == false)) { |
| pr_warn("%s: failed to hold suspend\n", __func__); |
| r = IRQ_NONE; |
| } else { |
| /* Call handler */ |
| wcd9xxx_swch_irq_handler(mbhc); |
| wcd9xxx_unlock_sleep(mbhc->resmgr->core_res); |
| } |
| |
| pr_debug("%s: leave %d\n", __func__, r); |
| return r; |
| } |
| |
| static int wcd9xxx_is_false_press(struct wcd9xxx_mbhc *mbhc) |
| { |
| s16 mb_v; |
| int i = 0; |
| int r = 0; |
| const s16 v_ins_hu = |
| wcd9xxx_get_current_v(mbhc, WCD9XXX_CURRENT_V_INS_HU); |
| const s16 v_ins_h = |
| wcd9xxx_get_current_v(mbhc, WCD9XXX_CURRENT_V_INS_H); |
| const s16 v_b1_hu = |
| wcd9xxx_get_current_v(mbhc, WCD9XXX_CURRENT_V_B1_HU); |
| const s16 v_b1_h = |
| wcd9xxx_get_current_v(mbhc, WCD9XXX_CURRENT_V_B1_H); |
| const unsigned long timeout = |
| jiffies + msecs_to_jiffies(BTN_RELEASE_DEBOUNCE_TIME_MS); |
| |
| while (time_before(jiffies, timeout)) { |
| /* |
| * This function needs to run measurements just few times during |
| * release debounce time. Make 1ms interval to avoid |
| * unnecessary excessive measurements. |
| */ |
| usleep_range(1000, 1000 + WCD9XXX_USLEEP_RANGE_MARGIN_US); |
| if (i == 0) { |
| mb_v = wcd9xxx_codec_sta_dce(mbhc, 0, true); |
| pr_debug("%s: STA[0]: %d,%d\n", __func__, mb_v, |
| wcd9xxx_codec_sta_dce_v(mbhc, 0, mb_v)); |
| if (mb_v < v_b1_hu || mb_v > v_ins_hu) { |
| r = 1; |
| break; |
| } |
| } else { |
| mb_v = wcd9xxx_codec_sta_dce(mbhc, 1, true); |
| pr_debug("%s: DCE[%d]: %d,%d\n", __func__, i, mb_v, |
| wcd9xxx_codec_sta_dce_v(mbhc, 1, mb_v)); |
| if (mb_v < v_b1_h || mb_v > v_ins_h) { |
| r = 1; |
| break; |
| } |
| } |
| i++; |
| } |
| |
| return r; |
| } |
| |
| /* called under codec_resource_lock acquisition */ |
| static int wcd9xxx_determine_button(const struct wcd9xxx_mbhc *mbhc, |
| const s32 micmv) |
| { |
| s16 *v_btn_low, *v_btn_high; |
| struct wcd9xxx_mbhc_btn_detect_cfg *btn_det; |
| int i, btn = -1; |
| |
| btn_det = WCD9XXX_MBHC_CAL_BTN_DET_PTR(mbhc->mbhc_cfg->calibration); |
| v_btn_low = wcd9xxx_mbhc_cal_btn_det_mp(btn_det, |
| MBHC_BTN_DET_V_BTN_LOW); |
| v_btn_high = wcd9xxx_mbhc_cal_btn_det_mp(btn_det, |
| MBHC_BTN_DET_V_BTN_HIGH); |
| |
| for (i = 0; i < btn_det->num_btn; i++) { |
| if ((v_btn_low[i] <= micmv) && (v_btn_high[i] >= micmv)) { |
| btn = i; |
| break; |
| } |
| } |
| |
| if (btn == -1) |
| pr_debug("%s: couldn't find button number for mic mv %d\n", |
| __func__, micmv); |
| |
| return btn; |
| } |
| |
| static int wcd9xxx_get_button_mask(const int btn) |
| { |
| int mask = 0; |
| switch (btn) { |
| case 0: |
| mask = SND_JACK_BTN_0; |
| break; |
| case 1: |
| mask = SND_JACK_BTN_1; |
| break; |
| case 2: |
| mask = SND_JACK_BTN_2; |
| break; |
| case 3: |
| mask = SND_JACK_BTN_3; |
| break; |
| case 4: |
| mask = SND_JACK_BTN_4; |
| break; |
| case 5: |
| mask = SND_JACK_BTN_5; |
| break; |
| case 6: |
| mask = SND_JACK_BTN_6; |
| break; |
| case 7: |
| mask = SND_JACK_BTN_7; |
| break; |
| } |
| return mask; |
| } |
| |
| static void wcd9xxx_get_z(struct wcd9xxx_mbhc *mbhc, s16 *dce_z, s16 *sta_z) |
| { |
| s16 reg0, reg1; |
| int change; |
| struct snd_soc_codec *codec = mbhc->codec; |
| |
| WCD9XXX_BCL_ASSERT_LOCKED(mbhc->resmgr); |
| /* Pull down micbias to ground and disconnect vddio switch */ |
| reg0 = snd_soc_read(codec, mbhc->mbhc_bias_regs.ctl_reg); |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.ctl_reg, 0x81, 0x1); |
| reg1 = snd_soc_read(codec, mbhc->mbhc_bias_regs.mbhc_reg); |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.mbhc_reg, 1 << 7, 0); |
| |
| /* Disconnect override from micbias */ |
| change = snd_soc_update_bits(codec, WCD9XXX_A_MAD_ANA_CTRL, 1 << 4, |
| 1 << 0); |
| usleep_range(1000, 1000 + 1000); |
| if (sta_z) { |
| *sta_z = wcd9xxx_codec_sta_dce(mbhc, 0, false); |
| pr_debug("%s: sta_z 0x%x\n", __func__, *sta_z & 0xFFFF); |
| } |
| if (dce_z) { |
| *dce_z = wcd9xxx_codec_sta_dce(mbhc, 1, false); |
| pr_debug("%s: dce_z 0x%x\n", __func__, *dce_z & 0xFFFF); |
| } |
| |
| /* Connect override from micbias */ |
| if (change) |
| snd_soc_update_bits(codec, WCD9XXX_A_MAD_ANA_CTRL, 1 << 4, |
| 1 << 4); |
| /* Disable pull down micbias to ground */ |
| snd_soc_write(codec, mbhc->mbhc_bias_regs.mbhc_reg, reg1); |
| snd_soc_write(codec, mbhc->mbhc_bias_regs.ctl_reg, reg0); |
| } |
| |
| void wcd9xxx_update_z(struct wcd9xxx_mbhc *mbhc) |
| { |
| const u16 sta_z = mbhc->mbhc_data.sta_z; |
| const u16 dce_z = mbhc->mbhc_data.dce_z; |
| |
| wcd9xxx_get_z(mbhc, &mbhc->mbhc_data.dce_z, &mbhc->mbhc_data.sta_z); |
| pr_debug("%s: sta_z 0x%x,dce_z 0x%x -> sta_z 0x%x,dce_z 0x%x\n", |
| __func__, sta_z & 0xFFFF, dce_z & 0xFFFF, |
| mbhc->mbhc_data.sta_z & 0xFFFF, |
| mbhc->mbhc_data.dce_z & 0xFFFF); |
| |
| wcd9xxx_mbhc_calc_thres(mbhc); |
| wcd9xxx_calibrate_hs_polling(mbhc); |
| } |
| |
| /* |
| * wcd9xxx_update_rel_threshold : update mbhc release upper bound threshold |
| * to ceilmv + buffer |
| */ |
| static int wcd9xxx_update_rel_threshold(struct wcd9xxx_mbhc *mbhc, int ceilmv) |
| { |
| u16 v_brh, v_b1_hu; |
| int mv; |
| struct wcd9xxx_mbhc_btn_detect_cfg *btn_det; |
| void *calibration = mbhc->mbhc_cfg->calibration; |
| struct snd_soc_codec *codec = mbhc->codec; |
| |
| btn_det = WCD9XXX_MBHC_CAL_BTN_DET_PTR(calibration); |
| mv = ceilmv + btn_det->v_btn_press_delta_cic; |
| pr_debug("%s: reprogram vb1hu/vbrh to %dmv\n", __func__, mv); |
| |
| /* update LSB first so mbhc hardware block doesn't see too low value */ |
| v_b1_hu = wcd9xxx_codec_v_sta_dce(mbhc, STA, mv, false); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B3_CTL, v_b1_hu & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B4_CTL, |
| (v_b1_hu >> 8) & 0xFF); |
| v_brh = wcd9xxx_codec_v_sta_dce(mbhc, DCE, mv, false); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B9_CTL, v_brh & 0xFF); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_VOLT_B10_CTL, |
| (v_brh >> 8) & 0xFF); |
| return 0; |
| } |
| |
| irqreturn_t wcd9xxx_dce_handler(int irq, void *data) |
| { |
| int i, mask; |
| bool vddio; |
| u8 mbhc_status; |
| s16 dce_z, sta_z; |
| s32 stamv, stamv_s; |
| s16 *v_btn_high; |
| struct wcd9xxx_mbhc_btn_detect_cfg *btn_det; |
| int btn = -1, meas = 0; |
| struct wcd9xxx_mbhc *mbhc = data; |
| const struct wcd9xxx_mbhc_btn_detect_cfg *d = |
| WCD9XXX_MBHC_CAL_BTN_DET_PTR(mbhc->mbhc_cfg->calibration); |
| short btnmeas[d->n_btn_meas + 1]; |
| short dce[d->n_btn_meas + 1], sta; |
| s32 mv[d->n_btn_meas + 1], mv_s[d->n_btn_meas + 1]; |
| struct snd_soc_codec *codec = mbhc->codec; |
| struct wcd9xxx_core_resource *core_res = mbhc->resmgr->core_res; |
| int n_btn_meas = d->n_btn_meas; |
| void *calibration = mbhc->mbhc_cfg->calibration; |
| |
| pr_debug("%s: enter\n", __func__); |
| |
| WCD9XXX_BCL_LOCK(mbhc->resmgr); |
| mbhc_status = snd_soc_read(codec, WCD9XXX_A_CDC_MBHC_B1_STATUS) & 0x3E; |
| |
| if (mbhc->mbhc_state == MBHC_STATE_POTENTIAL_RECOVERY) { |
| pr_debug("%s: mbhc is being recovered, skip button press\n", |
| __func__); |
| goto done; |
| } |
| |
| mbhc->mbhc_state = MBHC_STATE_POTENTIAL; |
| |
| if (!mbhc->polling_active) { |
| pr_warn("%s: mbhc polling is not active, skip button press\n", |
| __func__); |
| goto done; |
| } |
| |
| /* If switch nterrupt already kicked in, ignore button press */ |
| if (mbhc->in_swch_irq_handler) { |
| pr_debug("%s: Swtich level changed, ignore button press\n", |
| __func__); |
| btn = -1; |
| goto done; |
| } |
| |
| /* Measure scaled HW DCE */ |
| vddio = (mbhc->mbhc_data.micb_mv != VDDIO_MICBIAS_MV && |
| mbhc->mbhc_micbias_switched); |
| |
| dce_z = mbhc->mbhc_data.dce_z; |
| sta_z = mbhc->mbhc_data.sta_z; |
| |
| /* Measure scaled HW STA */ |
| dce[0] = wcd9xxx_read_dce_result(codec); |
| sta = wcd9xxx_read_sta_result(codec); |
| if (mbhc_status != STATUS_REL_DETECTION) { |
| if (mbhc->mbhc_last_resume && |
| !time_after(jiffies, mbhc->mbhc_last_resume + HZ)) { |
| pr_debug("%s: Button is released after resume\n", |
| __func__); |
| n_btn_meas = 0; |
| } else { |
| pr_debug("%s: Button is released without resume", |
| __func__); |
| if (mbhc->update_z) { |
| wcd9xxx_update_z(mbhc); |
| mbhc->update_z = false; |
| } |
| stamv = __wcd9xxx_codec_sta_dce_v(mbhc, 0, sta, sta_z, |
| mbhc->mbhc_data.micb_mv); |
| if (vddio) |
| stamv_s = scale_v_micb_vddio(mbhc, stamv, |
| false); |
| else |
| stamv_s = stamv; |
| mv[0] = __wcd9xxx_codec_sta_dce_v(mbhc, 1, dce[0], |
| dce_z, mbhc->mbhc_data.micb_mv); |
| mv_s[0] = vddio ? scale_v_micb_vddio(mbhc, mv[0], |
| false) : mv[0]; |
| btn = wcd9xxx_determine_button(mbhc, mv_s[0]); |
| if (btn != wcd9xxx_determine_button(mbhc, stamv_s)) |
| btn = -1; |
| goto done; |
| } |
| } |
| |
| for (meas = 1; ((d->n_btn_meas) && (meas < (d->n_btn_meas + 1))); |
| meas++) |
| dce[meas] = wcd9xxx_codec_sta_dce(mbhc, 1, false); |
| |
| if (mbhc->update_z) { |
| wcd9xxx_update_z(mbhc); |
| mbhc->update_z = false; |
| } |
| |
| stamv = __wcd9xxx_codec_sta_dce_v(mbhc, 0, sta, sta_z, |
| mbhc->mbhc_data.micb_mv); |
| if (vddio) |
| stamv_s = scale_v_micb_vddio(mbhc, stamv, false); |
| else |
| stamv_s = stamv; |
| pr_debug("%s: Meas HW - STA 0x%x,%d,%d\n", __func__, |
| sta & 0xFFFF, stamv, stamv_s); |
| |
| /* determine pressed button */ |
| mv[0] = __wcd9xxx_codec_sta_dce_v(mbhc, 1, dce[0], dce_z, |
| mbhc->mbhc_data.micb_mv); |
| mv_s[0] = vddio ? scale_v_micb_vddio(mbhc, mv[0], false) : mv[0]; |
| btnmeas[0] = wcd9xxx_determine_button(mbhc, mv_s[0]); |
| pr_debug("%s: Meas HW - DCE 0x%x,%d,%d button %d\n", __func__, |
| dce[0] & 0xFFFF, mv[0], mv_s[0], btnmeas[0]); |
| if (n_btn_meas == 0) |
| btn = btnmeas[0]; |
| for (meas = 1; (n_btn_meas && d->n_btn_meas && |
| (meas < (d->n_btn_meas + 1))); meas++) { |
| mv[meas] = __wcd9xxx_codec_sta_dce_v(mbhc, 1, dce[meas], dce_z, |
| mbhc->mbhc_data.micb_mv); |
| mv_s[meas] = vddio ? scale_v_micb_vddio(mbhc, mv[meas], false) : |
| mv[meas]; |
| btnmeas[meas] = wcd9xxx_determine_button(mbhc, mv_s[meas]); |
| pr_debug("%s: Meas %d - DCE 0x%x,%d,%d button %d\n", |
| __func__, meas, dce[meas] & 0xFFFF, mv[meas], |
| mv_s[meas], btnmeas[meas]); |
| /* |
| * if large enough measurements are collected, |
| * start to check if last all n_btn_con measurements were |
| * in same button low/high range |
| */ |
| if (meas + 1 >= d->n_btn_con) { |
| for (i = 0; i < d->n_btn_con; i++) |
| if ((btnmeas[meas] < 0) || |
| (btnmeas[meas] != btnmeas[meas - i])) |
| break; |
| if (i == d->n_btn_con) { |
| /* button pressed */ |
| btn = btnmeas[meas]; |
| break; |
| } else if ((n_btn_meas - meas) < (d->n_btn_con - 1)) { |
| /* |
| * if left measurements are less than n_btn_con, |
| * it's impossible to find button number |
| */ |
| break; |
| } |
| } |
| } |
| |
| if (btn >= 0) { |
| if (mbhc->in_swch_irq_handler) { |
| pr_debug( |
| "%s: Switch irq triggered, ignore button press\n", |
| __func__); |
| goto done; |
| } |
| btn_det = WCD9XXX_MBHC_CAL_BTN_DET_PTR(calibration); |
| v_btn_high = wcd9xxx_mbhc_cal_btn_det_mp(btn_det, |
| MBHC_BTN_DET_V_BTN_HIGH); |
| WARN_ON(btn >= btn_det->num_btn); |
| /* reprogram release threshold to catch voltage ramp up early */ |
| wcd9xxx_update_rel_threshold(mbhc, v_btn_high[btn]); |
| |
| mask = wcd9xxx_get_button_mask(btn); |
| mbhc->buttons_pressed |= mask; |
| wcd9xxx_lock_sleep(core_res); |
| if (schedule_delayed_work(&mbhc->mbhc_btn_dwork, |
| msecs_to_jiffies(400)) == 0) { |
| WARN(1, "Button pressed twice without release event\n"); |
| wcd9xxx_unlock_sleep(core_res); |
| } |
| } else { |
| pr_debug("%s: bogus button press, too short press?\n", |
| __func__); |
| } |
| |
| done: |
| pr_debug("%s: leave\n", __func__); |
| WCD9XXX_BCL_UNLOCK(mbhc->resmgr); |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t wcd9xxx_release_handler(int irq, void *data) |
| { |
| int ret; |
| bool waitdebounce = true; |
| struct wcd9xxx_mbhc *mbhc = data; |
| |
| pr_debug("%s: enter\n", __func__); |
| WCD9XXX_BCL_LOCK(mbhc->resmgr); |
| mbhc->mbhc_state = MBHC_STATE_RELEASE; |
| |
| if (mbhc->buttons_pressed & WCD9XXX_JACK_BUTTON_MASK) { |
| ret = wcd9xxx_cancel_btn_work(mbhc); |
| if (ret == 0) { |
| pr_debug("%s: Reporting long button release event\n", |
| __func__); |
| wcd9xxx_jack_report(mbhc, &mbhc->button_jack, 0, |
| mbhc->buttons_pressed); |
| } else { |
| if (wcd9xxx_is_false_press(mbhc)) { |
| pr_debug("%s: Fake button press interrupt\n", |
| __func__); |
| } else { |
| if (mbhc->in_swch_irq_handler) { |
| pr_debug("%s: Switch irq kicked in, ignore\n", |
| __func__); |
| } else { |
| pr_debug("%s: Reporting btn press\n", |
| __func__); |
| wcd9xxx_jack_report(mbhc, |
| &mbhc->button_jack, |
| mbhc->buttons_pressed, |
| mbhc->buttons_pressed); |
| pr_debug("%s: Reporting btn release\n", |
| __func__); |
| wcd9xxx_jack_report(mbhc, |
| &mbhc->button_jack, |
| 0, mbhc->buttons_pressed); |
| waitdebounce = false; |
| } |
| } |
| } |
| |
| mbhc->buttons_pressed &= ~WCD9XXX_JACK_BUTTON_MASK; |
| } |
| |
| wcd9xxx_calibrate_hs_polling(mbhc); |
| |
| if (waitdebounce) |
| msleep(SWCH_REL_DEBOUNCE_TIME_MS); |
| wcd9xxx_start_hs_polling(mbhc); |
| |
| pr_debug("%s: leave\n", __func__); |
| WCD9XXX_BCL_UNLOCK(mbhc->resmgr); |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t wcd9xxx_hphl_ocp_irq(int irq, void *data) |
| { |
| struct wcd9xxx_mbhc *mbhc = data; |
| struct snd_soc_codec *codec; |
| |
| pr_info("%s: received HPHL OCP irq\n", __func__); |
| |
| if (mbhc) { |
| codec = mbhc->codec; |
| if ((mbhc->hphlocp_cnt < OCP_ATTEMPT) && |
| (!mbhc->hphrocp_cnt)) { |
| pr_info("%s: retry\n", __func__); |
| mbhc->hphlocp_cnt++; |
| snd_soc_update_bits(codec, WCD9XXX_A_RX_HPH_OCP_CTL, |
| 0x10, 0x00); |
| snd_soc_update_bits(codec, WCD9XXX_A_RX_HPH_OCP_CTL, |
| 0x10, 0x10); |
| } else { |
| wcd9xxx_disable_irq(mbhc->resmgr->core_res, |
| WCD9XXX_IRQ_HPH_PA_OCPL_FAULT); |
| mbhc->hph_status |= SND_JACK_OC_HPHL; |
| wcd9xxx_jack_report(mbhc, &mbhc->headset_jack, |
| mbhc->hph_status, |
| WCD9XXX_JACK_MASK); |
| } |
| } else { |
| pr_err("%s: Bad wcd9xxx private data\n", __func__); |
| } |
| |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t wcd9xxx_hphr_ocp_irq(int irq, void *data) |
| { |
| struct wcd9xxx_mbhc *mbhc = data; |
| struct snd_soc_codec *codec; |
| |
| pr_info("%s: received HPHR OCP irq\n", __func__); |
| codec = mbhc->codec; |
| if ((mbhc->hphrocp_cnt < OCP_ATTEMPT) && |
| (!mbhc->hphlocp_cnt)) { |
| pr_info("%s: retry\n", __func__); |
| mbhc->hphrocp_cnt++; |
| snd_soc_update_bits(codec, WCD9XXX_A_RX_HPH_OCP_CTL, 0x10, |
| 0x00); |
| snd_soc_update_bits(codec, WCD9XXX_A_RX_HPH_OCP_CTL, 0x10, |
| 0x10); |
| } else { |
| wcd9xxx_disable_irq(mbhc->resmgr->core_res, |
| WCD9XXX_IRQ_HPH_PA_OCPR_FAULT); |
| mbhc->hph_status |= SND_JACK_OC_HPHR; |
| wcd9xxx_jack_report(mbhc, &mbhc->headset_jack, |
| mbhc->hph_status, WCD9XXX_JACK_MASK); |
| } |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int wcd9xxx_acdb_mclk_index(const int rate) |
| { |
| if (rate == MCLK_RATE_12288KHZ) |
| return 0; |
| else if (rate == MCLK_RATE_9600KHZ) |
| return 1; |
| else { |
| BUG_ON(1); |
| return -EINVAL; |
| } |
| } |
| |
| static void wcd9xxx_update_mbhc_clk_rate(struct wcd9xxx_mbhc *mbhc, u32 rate) |
| { |
| u32 dce_wait, sta_wait; |
| u8 ncic, nmeas, navg; |
| void *calibration; |
| u8 *n_cic, *n_ready; |
| struct wcd9xxx_mbhc_btn_detect_cfg *btn_det; |
| u8 npoll = 4, nbounce_wait = 30; |
| struct snd_soc_codec *codec = mbhc->codec; |
| int idx = wcd9xxx_acdb_mclk_index(rate); |
| int idxmclk = wcd9xxx_acdb_mclk_index(mbhc->mbhc_cfg->mclk_rate); |
| |
| pr_debug("%s: Updating clock rate dependents, rate = %u\n", __func__, |
| rate); |
| calibration = mbhc->mbhc_cfg->calibration; |
| |
| /* |
| * First compute the DCE / STA wait times depending on tunable |
| * parameters. The value is computed in microseconds |
| */ |
| btn_det = WCD9XXX_MBHC_CAL_BTN_DET_PTR(calibration); |
| n_ready = wcd9xxx_mbhc_cal_btn_det_mp(btn_det, MBHC_BTN_DET_N_READY); |
| n_cic = wcd9xxx_mbhc_cal_btn_det_mp(btn_det, MBHC_BTN_DET_N_CIC); |
| nmeas = WCD9XXX_MBHC_CAL_BTN_DET_PTR(calibration)->n_meas; |
| navg = WCD9XXX_MBHC_CAL_GENERAL_PTR(calibration)->mbhc_navg; |
| |
| /* ncic stays with the same what we had during calibration */ |
| ncic = n_cic[idxmclk]; |
| dce_wait = (1000 * 512 * ncic * (nmeas + 1)) / (rate / 1000); |
| sta_wait = (1000 * 128 * (navg + 1)) / (rate / 1000); |
| mbhc->mbhc_data.t_dce = dce_wait; |
| /* give extra margin to sta for safety */ |
| mbhc->mbhc_data.t_sta = sta_wait + 250; |
| mbhc->mbhc_data.t_sta_dce = ((1000 * 256) / (rate / 1000) * |
| n_ready[idx]) + 10; |
| |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_TIMER_B1_CTL, n_ready[idx]); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_TIMER_B6_CTL, ncic); |
| |
| if (rate == MCLK_RATE_12288KHZ) { |
| npoll = 4; |
| nbounce_wait = 30; |
| } else if (rate == MCLK_RATE_9600KHZ) { |
| npoll = 3; |
| nbounce_wait = 23; |
| } |
| |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_TIMER_B2_CTL, npoll); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_TIMER_B3_CTL, nbounce_wait); |
| pr_debug("%s: leave\n", __func__); |
| } |
| |
| static void wcd9xxx_mbhc_cal(struct wcd9xxx_mbhc *mbhc) |
| { |
| u8 cfilt_mode; |
| u16 reg0, reg1, reg2; |
| struct snd_soc_codec *codec = mbhc->codec; |
| |
| pr_debug("%s: enter\n", __func__); |
| wcd9xxx_disable_irq(mbhc->resmgr->core_res, WCD9XXX_IRQ_MBHC_POTENTIAL); |
| wcd9xxx_turn_onoff_rel_detection(codec, false); |
| |
| /* t_dce and t_sta are updated by wcd9xxx_update_mbhc_clk_rate() */ |
| WARN_ON(!mbhc->mbhc_data.t_dce); |
| WARN_ON(!mbhc->mbhc_data.t_sta); |
| |
| /* |
| * LDOH and CFILT are already configured during pdata handling. |
| * Only need to make sure CFILT and bandgap are in Fast mode. |
| * Need to restore defaults once calculation is done. |
| * |
| * In case when Micbias is powered by external source, request |
| * turn on the external voltage source for Calibration. |
| */ |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mb_source) |
| mbhc->mbhc_cb->enable_mb_source(codec, true); |
| |
| cfilt_mode = snd_soc_read(codec, mbhc->mbhc_bias_regs.cfilt_ctl); |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->cfilt_fast_mode) |
| mbhc->mbhc_cb->cfilt_fast_mode(codec, mbhc); |
| else |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.cfilt_ctl, |
| 0x40, 0x00); |
| |
| /* |
| * Micbias, CFILT, LDOH, MBHC MUX mode settings |
| * to perform ADC calibration |
| */ |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->select_cfilt) |
| mbhc->mbhc_cb->select_cfilt(codec, mbhc); |
| else |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.ctl_reg, 0x60, |
| mbhc->mbhc_cfg->micbias << 5); |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.ctl_reg, 0x01, 0x00); |
| snd_soc_update_bits(codec, WCD9XXX_A_LDO_H_MODE_1, 0x60, 0x60); |
| snd_soc_write(codec, WCD9XXX_A_TX_7_MBHC_TEST_CTL, 0x78); |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->codec_specific_cal) |
| mbhc->mbhc_cb->codec_specific_cal(codec, mbhc); |
| else |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, |
| 0x04, 0x04); |
| |
| /* Pull down micbias to ground */ |
| reg0 = snd_soc_read(codec, mbhc->mbhc_bias_regs.ctl_reg); |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.ctl_reg, 1, 1); |
| /* Disconnect override from micbias */ |
| reg1 = snd_soc_read(codec, WCD9XXX_A_MAD_ANA_CTRL); |
| snd_soc_update_bits(codec, WCD9XXX_A_MAD_ANA_CTRL, 1 << 4, 1 << 0); |
| /* Connect the MUX to micbias */ |
| snd_soc_write(codec, WCD9XXX_A_MBHC_SCALING_MUX_1, 0x02); |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mux_bias_block) |
| mbhc->mbhc_cb->enable_mux_bias_block(codec); |
| else |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_SCALING_MUX_1, |
| 0x80, 0x80); |
| /* |
| * Hardware that has external cap can delay mic bias ramping down up |
| * to 50ms. |
| */ |
| msleep(WCD9XXX_MUX_SWITCH_READY_WAIT_MS); |
| /* DCE measurement for 0 voltage */ |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x0A); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x02); |
| mbhc->mbhc_data.dce_z = __wcd9xxx_codec_sta_dce(mbhc, 1, true, false); |
| |
| /* compute dce_z for current source */ |
| reg2 = snd_soc_read(codec, WCD9XXX_A_CDC_MBHC_B1_CTL); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, 0x78, |
| WCD9XXX_MBHC_NSC_CS << 3); |
| |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x0A); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x02); |
| mbhc->mbhc_data.dce_nsc_cs_z = __wcd9xxx_codec_sta_dce(mbhc, 1, true, |
| false); |
| pr_debug("%s: dce_z with nsc cs: 0x%x\n", __func__, |
| mbhc->mbhc_data.dce_nsc_cs_z); |
| |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, reg2); |
| |
| /* STA measurement for 0 voltage */ |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x0A); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x02); |
| mbhc->mbhc_data.sta_z = __wcd9xxx_codec_sta_dce(mbhc, 0, true, false); |
| |
| /* Restore registers */ |
| snd_soc_write(codec, mbhc->mbhc_bias_regs.ctl_reg, reg0); |
| snd_soc_write(codec, WCD9XXX_A_MAD_ANA_CTRL, reg1); |
| |
| /* DCE measurment for MB voltage */ |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x0A); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x02); |
| snd_soc_write(codec, WCD9XXX_A_MBHC_SCALING_MUX_1, 0x02); |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mux_bias_block) |
| mbhc->mbhc_cb->enable_mux_bias_block(codec); |
| else |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_SCALING_MUX_1, |
| 0x80, 0x80); |
| /* |
| * Hardware that has external cap can delay mic bias ramping down up |
| * to 50ms. |
| */ |
| msleep(WCD9XXX_MUX_SWITCH_READY_WAIT_MS); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_EN_CTL, 0x04); |
| usleep_range(mbhc->mbhc_data.t_dce, mbhc->mbhc_data.t_dce); |
| mbhc->mbhc_data.dce_mb = wcd9xxx_read_dce_result(codec); |
| |
| /* STA Measurement for MB Voltage */ |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x0A); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_EN_CTL, 0x02); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_CLK_CTL, 0x02); |
| snd_soc_write(codec, WCD9XXX_A_MBHC_SCALING_MUX_1, 0x02); |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mux_bias_block) |
| mbhc->mbhc_cb->enable_mux_bias_block(codec); |
| else |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_SCALING_MUX_1, |
| 0x80, 0x80); |
| /* |
| * Hardware that has external cap can delay mic bias ramping down up |
| * to 50ms. |
| */ |
| msleep(WCD9XXX_MUX_SWITCH_READY_WAIT_MS); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_EN_CTL, 0x02); |
| usleep_range(mbhc->mbhc_data.t_sta, mbhc->mbhc_data.t_sta); |
| mbhc->mbhc_data.sta_mb = wcd9xxx_read_sta_result(codec); |
| |
| /* Restore default settings. */ |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, 0x04, 0x00); |
| snd_soc_write(codec, mbhc->mbhc_bias_regs.cfilt_ctl, cfilt_mode); |
| snd_soc_write(codec, WCD9XXX_A_MBHC_SCALING_MUX_1, 0x04); |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mux_bias_block) |
| mbhc->mbhc_cb->enable_mux_bias_block(codec); |
| else |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_SCALING_MUX_1, |
| 0x80, 0x80); |
| usleep_range(100, 100); |
| |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mb_source) |
| mbhc->mbhc_cb->enable_mb_source(codec, false); |
| |
| wcd9xxx_enable_irq(mbhc->resmgr->core_res, WCD9XXX_IRQ_MBHC_POTENTIAL); |
| wcd9xxx_turn_onoff_rel_detection(codec, true); |
| |
| pr_debug("%s: leave\n", __func__); |
| } |
| |
| static void wcd9xxx_mbhc_setup(struct wcd9xxx_mbhc *mbhc) |
| { |
| int n; |
| u8 *gain; |
| struct wcd9xxx_mbhc_general_cfg *generic; |
| struct wcd9xxx_mbhc_btn_detect_cfg *btn_det; |
| struct snd_soc_codec *codec = mbhc->codec; |
| const int idx = wcd9xxx_acdb_mclk_index(mbhc->mbhc_cfg->mclk_rate); |
| |
| pr_debug("%s: enter\n", __func__); |
| generic = WCD9XXX_MBHC_CAL_GENERAL_PTR(mbhc->mbhc_cfg->calibration); |
| btn_det = WCD9XXX_MBHC_CAL_BTN_DET_PTR(mbhc->mbhc_cfg->calibration); |
| |
| for (n = 0; n < 8; n++) { |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_FIR_B1_CFG, |
| 0x07, n); |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_FIR_B2_CFG, |
| btn_det->c[n]); |
| } |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B2_CTL, 0x07, |
| btn_det->nc); |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_TIMER_B4_CTL, 0x70, |
| generic->mbhc_nsa << 4); |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_TIMER_B4_CTL, 0x0F, |
| btn_det->n_meas); |
| |
| snd_soc_write(codec, WCD9XXX_A_CDC_MBHC_TIMER_B5_CTL, |
| generic->mbhc_navg); |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, 0x80, 0x80); |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, 0x78, |
| btn_det->mbhc_nsc << 3); |
| |
| if (mbhc->mbhc_cb && |
| mbhc->mbhc_cb->get_cdc_type() != |
| WCD9XXX_CDC_TYPE_HELICON) { |
| if (mbhc->resmgr->reg_addr->micb_4_mbhc) |
| snd_soc_update_bits(codec, |
| mbhc->resmgr->reg_addr->micb_4_mbhc, |
| 0x03, MBHC_MICBIAS2); |
| } |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B1_CTL, 0x02, 0x02); |
| |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_SCALING_MUX_2, 0xF0, 0xF0); |
| |
| gain = wcd9xxx_mbhc_cal_btn_det_mp(btn_det, MBHC_BTN_DET_GAIN); |
| snd_soc_update_bits(codec, WCD9XXX_A_CDC_MBHC_B2_CTL, 0x78, |
| gain[idx] << 3); |
| |
| pr_debug("%s: leave\n", __func__); |
| } |
| |
| static int wcd9xxx_setup_jack_detect_irq(struct wcd9xxx_mbhc *mbhc) |
| { |
| int ret = 0; |
| struct snd_soc_codec *codec = mbhc->codec; |
| void *core_res = mbhc->resmgr->core_res; |
| int jack_irq; |
| |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->jack_detect_irq) |
| jack_irq = mbhc->mbhc_cb->jack_detect_irq(codec); |
| else |
| jack_irq = WCD9XXX_IRQ_MBHC_JACK_SWITCH_DEFAULT; |
| |
| if (mbhc->mbhc_cfg->gpio) { |
| ret = request_threaded_irq(mbhc->mbhc_cfg->gpio_irq, NULL, |
| wcd9xxx_mech_plug_detect_irq, |
| (IRQF_TRIGGER_RISING | |
| IRQF_TRIGGER_FALLING | |
| IRQF_DISABLED), |
| "headset detect", mbhc); |
| if (ret) { |
| pr_err("%s: Failed to request gpio irq %d\n", __func__, |
| mbhc->mbhc_cfg->gpio_irq); |
| } else { |
| ret = enable_irq_wake(mbhc->mbhc_cfg->gpio_irq); |
| if (ret) |
| pr_err("%s: Failed to enable wake up irq %d\n", |
| __func__, mbhc->mbhc_cfg->gpio_irq); |
| } |
| } else if (mbhc->mbhc_cfg->insert_detect) { |
| /* Enable HPHL_10K_SW */ |
| snd_soc_update_bits(mbhc->codec, WCD9XXX_A_RX_HPH_OCP_CTL, |
| 1 << 1, 1 << 1); |
| |
| ret = wcd9xxx_request_irq(core_res, jack_irq, |
| wcd9xxx_mech_plug_detect_irq, |
| "Jack Detect", |
| mbhc); |
| if (ret) |
| pr_err("%s: Failed to request insert detect irq %d\n", |
| __func__, jack_irq); |
| } |
| |
| return ret; |
| } |
| |
| static int wcd9xxx_init_and_calibrate(struct wcd9xxx_mbhc *mbhc) |
| { |
| int ret = 0; |
| struct snd_soc_codec *codec = mbhc->codec; |
| |
| pr_debug("%s: enter\n", __func__); |
| |
| /* Enable MCLK during calibration */ |
| wcd9xxx_onoff_ext_mclk(mbhc, true); |
| wcd9xxx_mbhc_setup(mbhc); |
| wcd9xxx_mbhc_cal(mbhc); |
| wcd9xxx_mbhc_calc_thres(mbhc); |
| wcd9xxx_onoff_ext_mclk(mbhc, false); |
| wcd9xxx_calibrate_hs_polling(mbhc); |
| |
| /* Enable Mic Bias pull down and HPH Switch to GND */ |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.ctl_reg, 0x01, 0x01); |
| snd_soc_update_bits(codec, WCD9XXX_A_MBHC_HPH, 0x01, 0x01); |
| INIT_WORK(&mbhc->correct_plug_swch, wcd9xxx_correct_swch_plug); |
| |
| if (!IS_ERR_VALUE(ret)) { |
| snd_soc_update_bits(codec, WCD9XXX_A_RX_HPH_OCP_CTL, 0x10, |
| 0x10); |
| wcd9xxx_enable_irq(mbhc->resmgr->core_res, |
| WCD9XXX_IRQ_HPH_PA_OCPL_FAULT); |
| wcd9xxx_enable_irq(mbhc->resmgr->core_res, |
| WCD9XXX_IRQ_HPH_PA_OCPR_FAULT); |
| |
| /* Initialize mechanical mbhc */ |
| ret = wcd9xxx_setup_jack_detect_irq(mbhc); |
| |
| if (!ret && mbhc->mbhc_cfg->gpio) { |
| /* Requested with IRQF_DISABLED */ |
| enable_irq(mbhc->mbhc_cfg->gpio_irq); |
| |
| /* Bootup time detection */ |
| wcd9xxx_swch_irq_handler(mbhc); |
| } else if (!ret && mbhc->mbhc_cfg->insert_detect) { |
| pr_debug("%s: Setting up codec own insert detection\n", |
| __func__); |
| /* Setup for insertion detection */ |
| wcd9xxx_insert_detect_setup(mbhc, true); |
| } |
| } |
| |
| pr_debug("%s: leave\n", __func__); |
| |
| return ret; |
| } |
| |
| static void wcd9xxx_mbhc_fw_read(struct work_struct *work) |
| { |
| struct delayed_work *dwork; |
| struct wcd9xxx_mbhc *mbhc; |
| struct snd_soc_codec *codec; |
| const struct firmware *fw; |
| int ret = -1, retry = 0; |
| |
| dwork = to_delayed_work(work); |
| mbhc = container_of(dwork, struct wcd9xxx_mbhc, mbhc_firmware_dwork); |
| codec = mbhc->codec; |
| |
| while (retry < FW_READ_ATTEMPTS) { |
| retry++; |
| pr_info("%s:Attempt %d to request MBHC firmware\n", |
| __func__, retry); |
| ret = request_firmware(&fw, "wcd9320/wcd9320_mbhc.bin", |
| codec->dev); |
| |
| if (ret != 0) { |
| usleep_range(FW_READ_TIMEOUT, FW_READ_TIMEOUT); |
| } else { |
| pr_info("%s: MBHC Firmware read succesful\n", __func__); |
| break; |
| } |
| } |
| |
| if (ret != 0) { |
| pr_err("%s: Cannot load MBHC firmware use default cal\n", |
| __func__); |
| } else if (wcd9xxx_mbhc_fw_validate(fw) == false) { |
| pr_err("%s: Invalid MBHC cal data size use default cal\n", |
| __func__); |
| release_firmware(fw); |
| } else { |
| mbhc->mbhc_cfg->calibration = (void *)fw->data; |
| mbhc->mbhc_fw = fw; |
| } |
| |
| (void) wcd9xxx_init_and_calibrate(mbhc); |
| } |
| |
| #ifdef CONFIG_DEBUG_FS |
| ssize_t codec_mbhc_debug_read(struct file *file, char __user *buf, |
| size_t count, loff_t *pos) |
| { |
| const int size = 768; |
| char buffer[size]; |
| int n = 0; |
| struct wcd9xxx_mbhc *mbhc = file->private_data; |
| const struct mbhc_internal_cal_data *p = &mbhc->mbhc_data; |
| const s16 v_ins_hu = |
| wcd9xxx_get_current_v(mbhc, WCD9XXX_CURRENT_V_INS_HU); |
| const s16 v_ins_h = |
| wcd9xxx_get_current_v(mbhc, WCD9XXX_CURRENT_V_INS_H); |
| const s16 v_b1_hu = |
| wcd9xxx_get_current_v(mbhc, WCD9XXX_CURRENT_V_B1_HU); |
| const s16 v_b1_h = |
| wcd9xxx_get_current_v(mbhc, WCD9XXX_CURRENT_V_B1_H); |
| const s16 v_br_h = |
| wcd9xxx_get_current_v(mbhc, WCD9XXX_CURRENT_V_BR_H); |
| |
| n = scnprintf(buffer, size - n, "dce_z = %x(%dmv)\n", |
| p->dce_z, wcd9xxx_codec_sta_dce_v(mbhc, 1, p->dce_z)); |
| n += scnprintf(buffer + n, size - n, "dce_mb = %x(%dmv)\n", |
| p->dce_mb, wcd9xxx_codec_sta_dce_v(mbhc, 1, p->dce_mb)); |
| n += scnprintf(buffer + n, size - n, "dce_nsc_cs_z = %x(%dmv)\n", |
| p->dce_nsc_cs_z, |
| __wcd9xxx_codec_sta_dce_v(mbhc, 1, p->dce_nsc_cs_z, |
| p->dce_nsc_cs_z, |
| VDDIO_MICBIAS_MV)); |
| n += scnprintf(buffer + n, size - n, "sta_z = %x(%dmv)\n", |
| p->sta_z, wcd9xxx_codec_sta_dce_v(mbhc, 0, p->sta_z)); |
| n += scnprintf(buffer + n, size - n, "sta_mb = %x(%dmv)\n", |
| p->sta_mb, wcd9xxx_codec_sta_dce_v(mbhc, 0, p->sta_mb)); |
| n += scnprintf(buffer + n, size - n, "t_dce = %d\n", p->t_dce); |
| n += scnprintf(buffer + n, size - n, "t_sta = %d\n", p->t_sta); |
| n += scnprintf(buffer + n, size - n, "micb_mv = %dmv\n", p->micb_mv); |
| n += scnprintf(buffer + n, size - n, "v_ins_hu = %x(%dmv)\n", |
| v_ins_hu, wcd9xxx_codec_sta_dce_v(mbhc, 0, v_ins_hu)); |
| n += scnprintf(buffer + n, size - n, "v_ins_h = %x(%dmv)\n", |
| v_ins_h, wcd9xxx_codec_sta_dce_v(mbhc, 1, v_ins_h)); |
| n += scnprintf(buffer + n, size - n, "v_b1_hu = %x(%dmv)\n", |
| v_b1_hu, wcd9xxx_codec_sta_dce_v(mbhc, 0, v_b1_hu)); |
| n += scnprintf(buffer + n, size - n, "v_b1_h = %x(%dmv)\n", |
| v_b1_h, wcd9xxx_codec_sta_dce_v(mbhc, 1, v_b1_h)); |
| n += scnprintf(buffer + n, size - n, "v_brh = %x(%dmv)\n", |
| v_br_h, wcd9xxx_codec_sta_dce_v(mbhc, 1, v_br_h)); |
| n += scnprintf(buffer + n, size - n, "v_brl = %x(%dmv)\n", p->v_brl, |
| wcd9xxx_codec_sta_dce_v(mbhc, 0, p->v_brl)); |
| n += scnprintf(buffer + n, size - n, "v_no_mic = %x(%dmv)\n", |
| p->v_no_mic, |
| wcd9xxx_codec_sta_dce_v(mbhc, 0, p->v_no_mic)); |
| n += scnprintf(buffer + n, size - n, "v_inval_ins_low = %d\n", |
| p->v_inval_ins_low); |
| n += scnprintf(buffer + n, size - n, "v_inval_ins_high = %d\n", |
| p->v_inval_ins_high); |
| n += scnprintf(buffer + n, size - n, "Insert detect insert = %d\n", |
| !wcd9xxx_swch_level_remove(mbhc)); |
| buffer[n] = 0; |
| |
| return simple_read_from_buffer(buf, count, pos, buffer, n); |
| } |
| |
| static int codec_debug_open(struct inode *inode, struct file *file) |
| { |
| file->private_data = inode->i_private; |
| return 0; |
| } |
| |
| static ssize_t codec_debug_write(struct file *filp, |
| const char __user *ubuf, size_t cnt, |
| loff_t *ppos) |
| { |
| char lbuf[32]; |
| char *buf; |
| int rc; |
| struct wcd9xxx_mbhc *mbhc = filp->private_data; |
| |
| if (cnt > sizeof(lbuf) - 1) |
| return -EINVAL; |
| |
| rc = copy_from_user(lbuf, ubuf, cnt); |
| if (rc) |
| return -EFAULT; |
| |
| lbuf[cnt] = '\0'; |
| buf = (char *)lbuf; |
| mbhc->no_mic_headset_override = (*strsep(&buf, " ") == '0') ? |
| false : true; |
| return rc; |
| } |
| |
| static const struct file_operations mbhc_trrs_debug_ops = { |
| .open = codec_debug_open, |
| .write = codec_debug_write, |
| }; |
| |
| static const struct file_operations mbhc_debug_ops = { |
| .open = codec_debug_open, |
| .read = codec_mbhc_debug_read, |
| }; |
| |
| static void wcd9xxx_init_debugfs(struct wcd9xxx_mbhc *mbhc) |
| { |
| mbhc->debugfs_poke = |
| debugfs_create_file("TRRS", S_IFREG | S_IRUGO, NULL, mbhc, |
| &mbhc_trrs_debug_ops); |
| mbhc->debugfs_mbhc = |
| debugfs_create_file("wcd9xxx_mbhc", S_IFREG | S_IRUGO, |
| NULL, mbhc, &mbhc_debug_ops); |
| } |
| |
| static void wcd9xxx_cleanup_debugfs(struct wcd9xxx_mbhc *mbhc) |
| { |
| debugfs_remove(mbhc->debugfs_poke); |
| debugfs_remove(mbhc->debugfs_mbhc); |
| } |
| #else |
| static void wcd9xxx_init_debugfs(struct wcd9xxx_mbhc *mbhc) |
| { |
| } |
| |
| static void wcd9xxx_cleanup_debugfs(struct wcd9xxx_mbhc *mbhc) |
| { |
| } |
| #endif |
| |
| int wcd9xxx_mbhc_start(struct wcd9xxx_mbhc *mbhc, |
| struct wcd9xxx_mbhc_config *mbhc_cfg) |
| { |
| int rc = 0; |
| struct snd_soc_codec *codec = mbhc->codec; |
| |
| pr_debug("%s: enter\n", __func__); |
| |
| if (!codec) { |
| pr_err("%s: no codec\n", __func__); |
| return -EINVAL; |
| } |
| |
| if (mbhc_cfg->mclk_rate != MCLK_RATE_12288KHZ && |
| mbhc_cfg->mclk_rate != MCLK_RATE_9600KHZ) { |
| pr_err("Error: unsupported clock rate %d\n", |
| mbhc_cfg->mclk_rate); |
| return -EINVAL; |
| } |
| |
| /* Save mbhc config */ |
| mbhc->mbhc_cfg = mbhc_cfg; |
| |
| /* Get HW specific mbhc registers' address */ |
| wcd9xxx_get_mbhc_micbias_regs(mbhc, &mbhc->mbhc_bias_regs); |
| |
| /* Put CFILT in fast mode by default */ |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->cfilt_fast_mode) |
| mbhc->mbhc_cb->cfilt_fast_mode(codec, mbhc); |
| else |
| snd_soc_update_bits(codec, mbhc->mbhc_bias_regs.cfilt_ctl, |
| 0x40, WCD9XXX_CFILT_FAST_MODE); |
| |
| /* |
| * setup internal micbias if codec uses internal micbias for |
| * headset detection |
| */ |
| if (mbhc->mbhc_cfg->use_int_rbias) { |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->setup_int_rbias) |
| mbhc->mbhc_cb->setup_int_rbias(codec, true); |
| else |
| pr_info("%s: internal bias is requested but codec did not provide callback\n", |
| __func__); |
| } |
| |
| /* |
| * If codec has specific clock gating for MBHC, |
| * remove the clock gate |
| */ |
| if (mbhc->mbhc_cb && |
| mbhc->mbhc_cb->enable_clock_gate) |
| mbhc->mbhc_cb->enable_clock_gate(mbhc->codec, true); |
| |
| if (!mbhc->mbhc_cfg->read_fw_bin || |
| (mbhc->mbhc_cfg->read_fw_bin && mbhc->mbhc_fw)) { |
| rc = wcd9xxx_init_and_calibrate(mbhc); |
| } else { |
| if (!mbhc->mbhc_fw) |
| schedule_delayed_work(&mbhc->mbhc_firmware_dwork, |
| usecs_to_jiffies(FW_READ_TIMEOUT)); |
| else |
| pr_debug("%s: Skipping to read mbhc fw, 0x%p\n", |
| __func__, mbhc->mbhc_fw); |
| } |
| |
| pr_debug("%s: leave %d\n", __func__, rc); |
| return rc; |
| } |
| EXPORT_SYMBOL(wcd9xxx_mbhc_start); |
| |
| void wcd9xxx_mbhc_stop(struct wcd9xxx_mbhc *mbhc) |
| { |
| if (mbhc->mbhc_fw) { |
| cancel_delayed_work_sync(&mbhc->mbhc_firmware_dwork); |
| release_firmware(mbhc->mbhc_fw); |
| mbhc->mbhc_fw = NULL; |
| } |
| } |
| EXPORT_SYMBOL(wcd9xxx_mbhc_stop); |
| |
| static enum wcd9xxx_micbias_num |
| wcd9xxx_event_to_micbias(const enum wcd9xxx_notify_event event) |
| { |
| enum wcd9xxx_micbias_num ret; |
| switch (event) { |
| case WCD9XXX_EVENT_PRE_MICBIAS_1_ON: |
| case WCD9XXX_EVENT_PRE_MICBIAS_1_OFF: |
| case WCD9XXX_EVENT_POST_MICBIAS_1_ON: |
| case WCD9XXX_EVENT_POST_MICBIAS_1_OFF: |
| ret = MBHC_MICBIAS1; |
| break; |
| case WCD9XXX_EVENT_PRE_MICBIAS_2_ON: |
| case WCD9XXX_EVENT_PRE_MICBIAS_2_OFF: |
| case WCD9XXX_EVENT_POST_MICBIAS_2_ON: |
| case WCD9XXX_EVENT_POST_MICBIAS_2_OFF: |
| ret = MBHC_MICBIAS2; |
| break; |
| case WCD9XXX_EVENT_PRE_MICBIAS_3_ON: |
| case WCD9XXX_EVENT_PRE_MICBIAS_3_OFF: |
| case WCD9XXX_EVENT_POST_MICBIAS_3_ON: |
| case WCD9XXX_EVENT_POST_MICBIAS_3_OFF: |
| ret = MBHC_MICBIAS3; |
| break; |
| case WCD9XXX_EVENT_PRE_MICBIAS_4_ON: |
| case WCD9XXX_EVENT_PRE_MICBIAS_4_OFF: |
| case WCD9XXX_EVENT_POST_MICBIAS_4_ON: |
| case WCD9XXX_EVENT_POST_MICBIAS_4_OFF: |
| ret = MBHC_MICBIAS4; |
| break; |
| default: |
| WARN_ONCE(1, "Cannot convert event %d to micbias\n", event); |
| ret = MBHC_MICBIAS_INVALID; |
| break; |
| } |
| return ret; |
| } |
| |
| static int wcd9xxx_event_to_cfilt(const enum wcd9xxx_notify_event event) |
| { |
| int ret; |
| switch (event) { |
| case WCD9XXX_EVENT_PRE_CFILT_1_OFF: |
| case WCD9XXX_EVENT_POST_CFILT_1_OFF: |
| case WCD9XXX_EVENT_PRE_CFILT_1_ON: |
| case WCD9XXX_EVENT_POST_CFILT_1_ON: |
| ret = WCD9XXX_CFILT1_SEL; |
| break; |
| case WCD9XXX_EVENT_PRE_CFILT_2_OFF: |
| case WCD9XXX_EVENT_POST_CFILT_2_OFF: |
| case WCD9XXX_EVENT_PRE_CFILT_2_ON: |
| case WCD9XXX_EVENT_POST_CFILT_2_ON: |
| ret = WCD9XXX_CFILT2_SEL; |
| break; |
| case WCD9XXX_EVENT_PRE_CFILT_3_OFF: |
| case WCD9XXX_EVENT_POST_CFILT_3_OFF: |
| case WCD9XXX_EVENT_PRE_CFILT_3_ON: |
| case WCD9XXX_EVENT_POST_CFILT_3_ON: |
| ret = WCD9XXX_CFILT3_SEL; |
| break; |
| default: |
| ret = -1; |
| } |
| return ret; |
| } |
| |
| static int wcd9xxx_get_mbhc_cfilt_sel(struct wcd9xxx_mbhc *mbhc) |
| { |
| int cfilt; |
| const struct wcd9xxx_pdata *pdata = mbhc->resmgr->pdata; |
| |
| switch (mbhc->mbhc_cfg->micbias) { |
| case MBHC_MICBIAS1: |
| cfilt = pdata->micbias.bias1_cfilt_sel; |
| break; |
| case MBHC_MICBIAS2: |
| cfilt = pdata->micbias.bias2_cfilt_sel; |
| break; |
| case MBHC_MICBIAS3: |
| cfilt = pdata->micbias.bias3_cfilt_sel; |
| break; |
| case MBHC_MICBIAS4: |
| cfilt = pdata->micbias.bias4_cfilt_sel; |
| break; |
| default: |
| cfilt = MBHC_MICBIAS_INVALID; |
| break; |
| } |
| return cfilt; |
| } |
| |
| static void wcd9xxx_enable_mbhc_txfe(struct wcd9xxx_mbhc *mbhc, bool on) |
| { |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mbhc_txfe) |
| mbhc->mbhc_cb->enable_mbhc_txfe(mbhc->codec, on); |
| else |
| snd_soc_update_bits(mbhc->codec, WCD9XXX_A_TX_7_MBHC_TEST_CTL, |
| 0x40, on ? 0x40 : 0x00); |
| } |
| |
| static int wcd9xxx_event_notify(struct notifier_block *self, unsigned long val, |
| void *data) |
| { |
| int ret = 0; |
| struct wcd9xxx_mbhc *mbhc = ((struct wcd9xxx_resmgr *)data)->mbhc; |
| struct snd_soc_codec *codec = mbhc->codec; |
| enum wcd9xxx_notify_event event = (enum wcd9xxx_notify_event)val; |
| |
| pr_debug("%s: enter event %s(%d)\n", __func__, |
| wcd9xxx_get_event_string(event), event); |
| |
| switch (event) { |
| /* MICBIAS usage change */ |
| case WCD9XXX_EVENT_PRE_MICBIAS_1_ON: |
| case WCD9XXX_EVENT_PRE_MICBIAS_2_ON: |
| case WCD9XXX_EVENT_PRE_MICBIAS_3_ON: |
| case WCD9XXX_EVENT_PRE_MICBIAS_4_ON: |
| if (mbhc->mbhc_cfg && mbhc->mbhc_cfg->micbias == |
| wcd9xxx_event_to_micbias(event)) { |
| wcd9xxx_switch_micbias(mbhc, 0); |
| /* |
| * Enable MBHC TxFE whenever micbias is |
| * turned ON and polling is active |
| */ |
| if (mbhc->polling_active) |
| wcd9xxx_enable_mbhc_txfe(mbhc, true); |
| } |
| break; |
| case WCD9XXX_EVENT_POST_MICBIAS_1_ON: |
| case WCD9XXX_EVENT_POST_MICBIAS_2_ON: |
| case WCD9XXX_EVENT_POST_MICBIAS_3_ON: |
| case WCD9XXX_EVENT_POST_MICBIAS_4_ON: |
| if (mbhc->mbhc_cfg && mbhc->mbhc_cfg->micbias == |
| wcd9xxx_event_to_micbias(event) && |
| wcd9xxx_mbhc_polling(mbhc)) { |
| /* if polling is on, restart it */ |
| wcd9xxx_pause_hs_polling(mbhc); |
| wcd9xxx_start_hs_polling(mbhc); |
| } |
| break; |
| case WCD9XXX_EVENT_POST_MICBIAS_1_OFF: |
| case WCD9XXX_EVENT_POST_MICBIAS_2_OFF: |
| case WCD9XXX_EVENT_POST_MICBIAS_3_OFF: |
| case WCD9XXX_EVENT_POST_MICBIAS_4_OFF: |
| if (mbhc->mbhc_cfg && mbhc->mbhc_cfg->micbias == |
| wcd9xxx_event_to_micbias(event)) { |
| if (mbhc->event_state & |
| (1 << MBHC_EVENT_PA_HPHL | 1 << MBHC_EVENT_PA_HPHR)) |
| wcd9xxx_switch_micbias(mbhc, 1); |
| /* |
| * Disable MBHC TxFE, in case it was enabled |
| * earlier when micbias was enabled. |
| */ |
| wcd9xxx_enable_mbhc_txfe(mbhc, false); |
| } |
| break; |
| /* PA usage change */ |
| case WCD9XXX_EVENT_PRE_HPHL_PA_ON: |
| set_bit(MBHC_EVENT_PA_HPHL, &mbhc->event_state); |
| if (!(snd_soc_read(codec, mbhc->mbhc_bias_regs.ctl_reg) & 0x80)) |
| /* if micbias is not enabled, switch to vddio */ |
| wcd9xxx_switch_micbias(mbhc, 1); |
| break; |
| case WCD9XXX_EVENT_PRE_HPHR_PA_ON: |
| set_bit(MBHC_EVENT_PA_HPHR, &mbhc->event_state); |
| break; |
| case WCD9XXX_EVENT_POST_HPHL_PA_OFF: |
| clear_bit(MBHC_EVENT_PA_HPHL, &mbhc->event_state); |
| /* if HPH PAs are off, report OCP and switch back to CFILT */ |
| clear_bit(WCD9XXX_HPHL_PA_OFF_ACK, &mbhc->hph_pa_dac_state); |
| clear_bit(WCD9XXX_HPHL_DAC_OFF_ACK, &mbhc->hph_pa_dac_state); |
| if (mbhc->hph_status & SND_JACK_OC_HPHL) |
| hphlocp_off_report(mbhc, SND_JACK_OC_HPHL); |
| if (!(mbhc->event_state & |
| (1 << MBHC_EVENT_PA_HPHL | 1 << MBHC_EVENT_PA_HPHR))) |
| wcd9xxx_switch_micbias(mbhc, 0); |
| break; |
| case WCD9XXX_EVENT_POST_HPHR_PA_OFF: |
| clear_bit(MBHC_EVENT_PA_HPHR, &mbhc->event_state); |
| /* if HPH PAs are off, report OCP and switch back to CFILT */ |
| clear_bit(WCD9XXX_HPHR_PA_OFF_ACK, &mbhc->hph_pa_dac_state); |
| clear_bit(WCD9XXX_HPHR_DAC_OFF_ACK, &mbhc->hph_pa_dac_state); |
| if (mbhc->hph_status & SND_JACK_OC_HPHR) |
| hphrocp_off_report(mbhc, SND_JACK_OC_HPHL); |
| if (!(mbhc->event_state & |
| (1 << MBHC_EVENT_PA_HPHL | 1 << MBHC_EVENT_PA_HPHR))) |
| wcd9xxx_switch_micbias(mbhc, 0); |
| break; |
| /* Clock usage change */ |
| case WCD9XXX_EVENT_PRE_MCLK_ON: |
| break; |
| case WCD9XXX_EVENT_POST_MCLK_ON: |
| /* Change to lower TxAAF frequency */ |
| snd_soc_update_bits(codec, WCD9XXX_A_TX_COM_BIAS, 1 << 4, |
| 1 << 4); |
| /* Re-calibrate clock rate dependent values */ |
| wcd9xxx_update_mbhc_clk_rate(mbhc, mbhc->mbhc_cfg->mclk_rate); |
| /* If clock source changes, stop and restart polling */ |
| if (wcd9xxx_mbhc_polling(mbhc)) { |
| wcd9xxx_calibrate_hs_polling(mbhc); |
| wcd9xxx_start_hs_polling(mbhc); |
| } |
| break; |
| case WCD9XXX_EVENT_PRE_MCLK_OFF: |
| /* If clock source changes, stop and restart polling */ |
| if (wcd9xxx_mbhc_polling(mbhc)) |
| wcd9xxx_pause_hs_polling(mbhc); |
| break; |
| case WCD9XXX_EVENT_POST_MCLK_OFF: |
| break; |
| case WCD9XXX_EVENT_PRE_RCO_ON: |
| break; |
| case WCD9XXX_EVENT_POST_RCO_ON: |
| /* Change to higher TxAAF frequency */ |
| snd_soc_update_bits(codec, WCD9XXX_A_TX_COM_BIAS, 1 << 4, |
| 0 << 4); |
| /* Re-calibrate clock rate dependent values */ |
| wcd9xxx_update_mbhc_clk_rate(mbhc, mbhc->rco_clk_rate); |
| /* If clock source changes, stop and restart polling */ |
| if (wcd9xxx_mbhc_polling(mbhc)) { |
| wcd9xxx_calibrate_hs_polling(mbhc); |
| wcd9xxx_start_hs_polling(mbhc); |
| } |
| break; |
| case WCD9XXX_EVENT_PRE_RCO_OFF: |
| /* If clock source changes, stop and restart polling */ |
| if (wcd9xxx_mbhc_polling(mbhc)) |
| wcd9xxx_pause_hs_polling(mbhc); |
| break; |
| case WCD9XXX_EVENT_POST_RCO_OFF: |
| break; |
| /* CFILT usage change */ |
| case WCD9XXX_EVENT_PRE_CFILT_1_ON: |
| case WCD9XXX_EVENT_PRE_CFILT_2_ON: |
| case WCD9XXX_EVENT_PRE_CFILT_3_ON: |
| if (wcd9xxx_get_mbhc_cfilt_sel(mbhc) == |
| wcd9xxx_event_to_cfilt(event)) |
| /* |
| * Switch CFILT to slow mode if MBHC CFILT is being |
| * used. |
| */ |
| wcd9xxx_codec_switch_cfilt_mode(mbhc, false); |
| break; |
| case WCD9XXX_EVENT_POST_CFILT_1_OFF: |
| case WCD9XXX_EVENT_POST_CFILT_2_OFF: |
| case WCD9XXX_EVENT_POST_CFILT_3_OFF: |
| if (wcd9xxx_get_mbhc_cfilt_sel(mbhc) == |
| wcd9xxx_event_to_cfilt(event)) |
| /* |
| * Switch CFILT to fast mode if MBHC CFILT is not |
| * used anymore. |
| */ |
| wcd9xxx_codec_switch_cfilt_mode(mbhc, true); |
| break; |
| /* System resume */ |
| case WCD9XXX_EVENT_POST_RESUME: |
| mbhc->mbhc_last_resume = jiffies; |
| break; |
| /* BG mode chage */ |
| case WCD9XXX_EVENT_PRE_BG_OFF: |
| case WCD9XXX_EVENT_POST_BG_OFF: |
| case WCD9XXX_EVENT_PRE_BG_AUDIO_ON: |
| case WCD9XXX_EVENT_POST_BG_AUDIO_ON: |
| case WCD9XXX_EVENT_PRE_BG_MBHC_ON: |
| case WCD9XXX_EVENT_POST_BG_MBHC_ON: |
| /* Not used for now */ |
| break; |
| default: |
| WARN(1, "Unknown event %d\n", event); |
| ret = -EINVAL; |
| } |
| |
| pr_debug("%s: leave\n", __func__); |
| |
| return ret; |
| } |
| |
| static int wcd9xxx_detect_impedance(struct wcd9xxx_mbhc *mbhc, uint32_t *zl, |
| uint32_t *zr) |
| { |
| int i; |
| int ret = 0; |
| s16 l[3], r[3]; |
| s16 *z[] = { |
| &l[0], &r[0], &r[1], &l[1], &l[2], &r[2], |
| }; |
| struct snd_soc_codec *codec = mbhc->codec; |
| const int mux_wait_us = 25; |
| const struct wcd9xxx_reg_mask_val reg_set_mux[] = { |
| /* Phase 1 */ |
| /* Set MBHC_MUX for HPHL without ical */ |
| {WCD9XXX_A_MBHC_SCALING_MUX_2, 0xFF, 0xF0}, |
| /* Set MBHC_MUX for HPHR without ical */ |
| {WCD9XXX_A_MBHC_SCALING_MUX_1, 0xFF, 0xA0}, |
| /* Set MBHC_MUX for HPHR with ical */ |
| {WCD9XXX_A_MBHC_SCALING_MUX_2, 0xFF, 0xF8}, |
| /* Set MBHC_MUX for HPHL with ical */ |
| {WCD9XXX_A_MBHC_SCALING_MUX_1, 0xFF, 0xC0}, |
| |
| /* Phase 2 */ |
| {WCD9XXX_A_MBHC_SCALING_MUX_2, 0xFF, 0xF0}, |
| /* Set MBHC_MUX for HPHR without ical and wait for 25us */ |
| {WCD9XXX_A_MBHC_SCALING_MUX_1, 0xFF, 0xA0}, |
| }; |
| |
| pr_debug("%s: enter\n", __func__); |
| WCD9XXX_BCL_ASSERT_LOCKED(mbhc->resmgr); |
| |
| if (!mbhc->mbhc_cb || !mbhc->mbhc_cb->setup_zdet || |
| !mbhc->mbhc_cb->compute_impedance || !zl || |
| !zr) |
| return -EINVAL; |
| |
| /* |
| * Impedance detection is an intrusive function as it mutes RX paths, |
| * enable PAs and etc. Therefore codec drvier including ALSA |
| * shouldn't read and write hardware registers during detection. |
| */ |
| mutex_lock(&codec->mutex); |
| |
| WCD9XXX_BG_CLK_LOCK(mbhc->resmgr); |
| /* |
| * Fast(mbhc) mode bandagap doesn't need to be enabled explicitly |
| * since fast mode is set by MBHC hardware when override is on. |
| * Enable bandgap mode to avoid unnecessary RCO disable and enable |
| * during clock source change. |
| */ |
| wcd9xxx_resmgr_get_bandgap(mbhc->resmgr, WCD9XXX_BANDGAP_AUDIO_MODE); |
| wcd9xxx_resmgr_get_clk_block(mbhc->resmgr, WCD9XXX_CLK_RCO); |
| WCD9XXX_BG_CLK_UNLOCK(mbhc->resmgr); |
| |
| wcd9xxx_turn_onoff_override(mbhc, true); |
| pr_debug("%s: Setting impedance detection\n", __func__); |
| |
| /* Codec specific setup for L0, R0, L1 and R1 measurements */ |
| mbhc->mbhc_cb->setup_zdet(mbhc, PRE_MEAS); |
| |
| pr_debug("%s: Performing impedance detection\n", __func__); |
| for (i = 0; i < ARRAY_SIZE(reg_set_mux) - 2; i++) { |
| snd_soc_update_bits(codec, reg_set_mux[i].reg, |
| reg_set_mux[i].mask, |
| reg_set_mux[i].val); |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mux_bias_block) |
| mbhc->mbhc_cb->enable_mux_bias_block(codec); |
| else |
| snd_soc_update_bits(codec, |
| WCD9XXX_A_MBHC_SCALING_MUX_1, |
| 0x80, 0x80); |
| /* 25us is required after mux change to settle down */ |
| usleep_range(mux_wait_us, |
| mux_wait_us + WCD9XXX_USLEEP_RANGE_MARGIN_US); |
| *(z[i]) = __wcd9xxx_codec_sta_dce(mbhc, 0, true, false); |
| } |
| |
| /* Codec specific setup for L2 and R2 measurements */ |
| mbhc->mbhc_cb->setup_zdet(mbhc, POST_MEAS); |
| |
| for (; i < ARRAY_SIZE(reg_set_mux); i++) { |
| snd_soc_update_bits(codec, reg_set_mux[i].reg, |
| reg_set_mux[i].mask, |
| reg_set_mux[i].val); |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->enable_mux_bias_block) |
| mbhc->mbhc_cb->enable_mux_bias_block(codec); |
| else |
| snd_soc_update_bits(codec, |
| WCD9XXX_A_MBHC_SCALING_MUX_1, |
| 0x80, 0x80); |
| /* 25us is required after mux change to settle down */ |
| usleep_range(mux_wait_us, |
| mux_wait_us + WCD9XXX_USLEEP_RANGE_MARGIN_US); |
| *(z[i]) = __wcd9xxx_codec_sta_dce(mbhc, 0, true, false); |
| } |
| |
| mbhc->mbhc_cb->setup_zdet(mbhc, PA_DISABLE); |
| |
| mutex_unlock(&codec->mutex); |
| |
| WCD9XXX_BG_CLK_LOCK(mbhc->resmgr); |
| wcd9xxx_resmgr_put_bandgap(mbhc->resmgr, WCD9XXX_BANDGAP_AUDIO_MODE); |
| wcd9xxx_resmgr_put_clk_block(mbhc->resmgr, WCD9XXX_CLK_RCO); |
| WCD9XXX_BG_CLK_UNLOCK(mbhc->resmgr); |
| |
| wcd9xxx_turn_onoff_override(mbhc, false); |
| mbhc->mbhc_cb->compute_impedance(l, r, zl, zr); |
| |
| pr_debug("%s: L0: 0x%x(%d), L1: 0x%x(%d), L2: 0x%x(%d)\n", |
| __func__, |
| l[0] & 0xffff, l[0], l[1] & 0xffff, l[1], l[2] & 0xffff, l[2]); |
| pr_debug("%s: R0: 0x%x(%d), R1: 0x%x(%d), R2: 0x%x(%d)\n", |
| __func__, |
| r[0] & 0xffff, r[0], r[1] & 0xffff, r[1], r[2] & 0xffff, r[2]); |
| pr_debug("%s: RL %d milliohm, RR %d milliohm\n", __func__, *zl, *zr); |
| pr_debug("%s: Impedance detection completed\n", __func__); |
| |
| return ret; |
| } |
| |
| int wcd9xxx_mbhc_get_impedance(struct wcd9xxx_mbhc *mbhc, uint32_t *zl, |
| uint32_t *zr) |
| { |
| WCD9XXX_BCL_LOCK(mbhc->resmgr); |
| *zl = mbhc->zl; |
| *zr = mbhc->zr; |
| WCD9XXX_BCL_UNLOCK(mbhc->resmgr); |
| |
| if (*zl && *zr) |
| return 0; |
| else |
| return -EINVAL; |
| } |
| |
| /* |
| * wcd9xxx_mbhc_init : initialize MBHC internal structures. |
| * |
| * NOTE: mbhc->mbhc_cfg is not YET configure so shouldn't be used |
| */ |
| int wcd9xxx_mbhc_init(struct wcd9xxx_mbhc *mbhc, struct wcd9xxx_resmgr *resmgr, |
| struct snd_soc_codec *codec, |
| int (*micbias_enable_cb) (struct snd_soc_codec*, bool), |
| const struct wcd9xxx_mbhc_cb *mbhc_cb, int rco_clk_rate, |
| bool impedance_det_en) |
| { |
| int ret; |
| void *core_res; |
| |
| pr_debug("%s: enter\n", __func__); |
| memset(&mbhc->mbhc_bias_regs, 0, sizeof(struct mbhc_micbias_regs)); |
| memset(&mbhc->mbhc_data, 0, sizeof(struct mbhc_internal_cal_data)); |
| |
| mbhc->mbhc_data.t_sta_dce = DEFAULT_DCE_STA_WAIT; |
| mbhc->mbhc_data.t_dce = DEFAULT_DCE_WAIT; |
| mbhc->mbhc_data.t_sta = DEFAULT_STA_WAIT; |
| mbhc->mbhc_micbias_switched = false; |
| mbhc->polling_active = false; |
| mbhc->mbhc_state = MBHC_STATE_NONE; |
| mbhc->in_swch_irq_handler = false; |
| mbhc->current_plug = PLUG_TYPE_NONE; |
| mbhc->lpi_enabled = false; |
| mbhc->no_mic_headset_override = false; |
| mbhc->mbhc_last_resume = 0; |
| mbhc->codec = codec; |
| mbhc->resmgr = resmgr; |
| mbhc->resmgr->mbhc = mbhc; |
| mbhc->micbias_enable_cb = micbias_enable_cb; |
| mbhc->rco_clk_rate = rco_clk_rate; |
| mbhc->mbhc_cb = mbhc_cb; |
| mbhc->impedance_detect = impedance_det_en; |
| impedance_detect_en = impedance_det_en ? 1 : 0; |
| |
| if (mbhc->headset_jack.jack == NULL) { |
| ret = snd_soc_jack_new(codec, "Headset Jack", WCD9XXX_JACK_MASK, |
| &mbhc->headset_jack); |
| if (ret) { |
| pr_err("%s: Failed to create new jack\n", __func__); |
| return ret; |
| } |
| |
| ret = snd_soc_jack_new(codec, "Button Jack", |
| WCD9XXX_JACK_BUTTON_MASK, |
| &mbhc->button_jack); |
| if (ret) { |
| pr_err("Failed to create new jack\n"); |
| return ret; |
| } |
| |
| ret = snd_jack_set_key(mbhc->button_jack.jack, |
| SND_JACK_BTN_0, |
| KEY_MEDIA); |
| if (ret) { |
| pr_err("%s: Failed to set code for btn-0\n", |
| __func__); |
| return ret; |
| } |
| |
| INIT_DELAYED_WORK(&mbhc->mbhc_firmware_dwork, |
| wcd9xxx_mbhc_fw_read); |
| INIT_DELAYED_WORK(&mbhc->mbhc_btn_dwork, wcd9xxx_btn_lpress_fn); |
| INIT_DELAYED_WORK(&mbhc->mbhc_insert_dwork, |
| wcd9xxx_mbhc_insert_work); |
| } |
| |
| /* Register event notifier */ |
| mbhc->nblock.notifier_call = wcd9xxx_event_notify; |
| ret = wcd9xxx_resmgr_register_notifier(mbhc->resmgr, &mbhc->nblock); |
| if (ret) { |
| pr_err("%s: Failed to register notifier %d\n", __func__, ret); |
| return ret; |
| } |
| |
| wcd9xxx_init_debugfs(mbhc); |
| |
| core_res = mbhc->resmgr->core_res; |
| ret = wcd9xxx_request_irq(core_res, WCD9XXX_IRQ_MBHC_INSERTION, |
| wcd9xxx_hs_insert_irq, |
| "Headset insert detect", mbhc); |
| if (ret) { |
| pr_err("%s: Failed to request irq %d, ret = %d\n", __func__, |
| WCD9XXX_IRQ_MBHC_INSERTION, ret); |
| goto err_insert_irq; |
| } |
| wcd9xxx_disable_irq(core_res, WCD9XXX_IRQ_MBHC_INSERTION); |
| |
| ret = wcd9xxx_request_irq(core_res, WCD9XXX_IRQ_MBHC_REMOVAL, |
| wcd9xxx_hs_remove_irq, |
| "Headset remove detect", mbhc); |
| if (ret) { |
| pr_err("%s: Failed to request irq %d\n", __func__, |
| WCD9XXX_IRQ_MBHC_REMOVAL); |
| goto err_remove_irq; |
| } |
| |
| ret = wcd9xxx_request_irq(core_res, WCD9XXX_IRQ_MBHC_POTENTIAL, |
| wcd9xxx_dce_handler, "DC Estimation detect", |
| mbhc); |
| if (ret) { |
| pr_err("%s: Failed to request irq %d\n", __func__, |
| WCD9XXX_IRQ_MBHC_POTENTIAL); |
| goto err_potential_irq; |
| } |
| |
| ret = wcd9xxx_request_irq(core_res, WCD9XXX_IRQ_MBHC_RELEASE, |
| wcd9xxx_release_handler, |
| "Button Release detect", mbhc); |
| if (ret) { |
| pr_err("%s: Failed to request irq %d\n", __func__, |
| WCD9XXX_IRQ_MBHC_RELEASE); |
| goto err_release_irq; |
| } |
| |
| ret = wcd9xxx_request_irq(core_res, WCD9XXX_IRQ_HPH_PA_OCPL_FAULT, |
| wcd9xxx_hphl_ocp_irq, "HPH_L OCP detect", |
| mbhc); |
| if (ret) { |
| pr_err("%s: Failed to request irq %d\n", __func__, |
| WCD9XXX_IRQ_HPH_PA_OCPL_FAULT); |
| goto err_hphl_ocp_irq; |
| } |
| wcd9xxx_disable_irq(core_res, WCD9XXX_IRQ_HPH_PA_OCPL_FAULT); |
| |
| ret = wcd9xxx_request_irq(core_res, WCD9XXX_IRQ_HPH_PA_OCPR_FAULT, |
| wcd9xxx_hphr_ocp_irq, "HPH_R OCP detect", |
| mbhc); |
| if (ret) { |
| pr_err("%s: Failed to request irq %d\n", __func__, |
| WCD9XXX_IRQ_HPH_PA_OCPR_FAULT); |
| goto err_hphr_ocp_irq; |
| } |
| wcd9xxx_disable_irq(core_res, WCD9XXX_IRQ_HPH_PA_OCPR_FAULT); |
| |
| wcd9xxx_regmgr_cond_register(resmgr, 1 << WCD9XXX_COND_HPH_MIC | |
| 1 << WCD9XXX_COND_HPH); |
| |
| pr_debug("%s: leave ret %d\n", __func__, ret); |
| return ret; |
| |
| err_hphr_ocp_irq: |
| wcd9xxx_free_irq(core_res, WCD9XXX_IRQ_HPH_PA_OCPL_FAULT, mbhc); |
| err_hphl_ocp_irq: |
| wcd9xxx_free_irq(core_res, WCD9XXX_IRQ_MBHC_RELEASE, mbhc); |
| err_release_irq: |
| wcd9xxx_free_irq(core_res, WCD9XXX_IRQ_MBHC_POTENTIAL, mbhc); |
| err_potential_irq: |
| wcd9xxx_free_irq(core_res, WCD9XXX_IRQ_MBHC_REMOVAL, mbhc); |
| err_remove_irq: |
| wcd9xxx_free_irq(core_res, WCD9XXX_IRQ_MBHC_INSERTION, mbhc); |
| err_insert_irq: |
| wcd9xxx_resmgr_unregister_notifier(mbhc->resmgr, &mbhc->nblock); |
| |
| pr_debug("%s: leave ret %d\n", __func__, ret); |
| return ret; |
| } |
| EXPORT_SYMBOL(wcd9xxx_mbhc_init); |
| |
| void wcd9xxx_mbhc_deinit(struct wcd9xxx_mbhc *mbhc) |
| { |
| struct wcd9xxx_core_resource *core_res = |
| mbhc->resmgr->core_res; |
| |
| wcd9xxx_regmgr_cond_deregister(mbhc->resmgr, 1 << WCD9XXX_COND_HPH_MIC | |
| 1 << WCD9XXX_COND_HPH); |
| |
| wcd9xxx_free_irq(core_res, WCD9XXX_IRQ_MBHC_RELEASE, mbhc); |
| wcd9xxx_free_irq(core_res, WCD9XXX_IRQ_MBHC_POTENTIAL, mbhc); |
| wcd9xxx_free_irq(core_res, WCD9XXX_IRQ_MBHC_REMOVAL, mbhc); |
| wcd9xxx_free_irq(core_res, WCD9XXX_IRQ_MBHC_INSERTION, mbhc); |
| |
| if (mbhc->mbhc_cb && mbhc->mbhc_cb->free_irq) |
| mbhc->mbhc_cb->free_irq(mbhc); |
| else |
| wcd9xxx_free_irq(core_res, WCD9320_IRQ_MBHC_JACK_SWITCH, |
| mbhc); |
| |
| wcd9xxx_free_irq(core_res, WCD9XXX_IRQ_HPH_PA_OCPL_FAULT, mbhc); |
| wcd9xxx_free_irq(core_res, WCD9XXX_IRQ_HPH_PA_OCPR_FAULT, mbhc); |
| |
| wcd9xxx_resmgr_unregister_notifier(mbhc->resmgr, &mbhc->nblock); |
| |
| wcd9xxx_cleanup_debugfs(mbhc); |
| } |
| EXPORT_SYMBOL(wcd9xxx_mbhc_deinit); |
| |
| MODULE_DESCRIPTION("wcd9xxx MBHC module"); |
| MODULE_LICENSE("GPL v2"); |