Documentation/devicetree/bindings/usb/msm-hsusb.txt - kernel/msm - Gitiles

 MSM SoC HSUSB controllers

 OTG:

 Required properties :
 - compatible : should be "qcom,hsusb-otg"
 - regs : offset and length of the register set in the memory map
 - interrupts: IRQ line
 - interrupt-names: OTG interrupt name(s) referenced in interrupts above
             HSUSB OTG expects "core_irq" and optionally "async_irq".
 - qcom,hsusb-otg-phy-type: PHY type can be one of
             1 - Chipidea 45nm PHY
 	    2 - Synopsis 28nm PHY
 - qcom,hsusb-otg-mode: Operational mode. Can be one of
             1 - Peripheral only mode
 	    2 - Host only mode
 	    3 - OTG mode
 	    Based on the mode, OTG driver registers platform devices for
 	    gadget and host.
 - qcom,hsusb-otg-control: OTG control (VBUS and ID notifications)
   can be one of
             1 - PHY control
 	    2 - PMIC control
 	    3 - User control (via debugfs)
 - <supply-name>-supply: handle to the regulator device tree node
          Required "supply-name" is "HSUSB_VDDCX" (when voting for VDDCX) or
          "hsusb_vdd_dig" (when voting for VDDCX Corner voltage),
          "HSUSB_1p8-supply" and "HSUSB_3p3-supply".

 Optional properties :
 - qcom,hsusb-otg-disable-reset: If present then core is RESET only during
 	    init, otherwise core is RESET for every cable disconnect as well
 - qcom,hsusb-otg-pnoc-errata-fix: If present then workaround for PNOC
 	    performance issue is applied which requires changing the mem-type
 	    attribute via VMIDMT.
 - qcom,hsusb-otg-default-mode: The default USB mode after boot-up.
   Applicable only when OTG is controlled by user. Can be one of
             0 - None. Low power mode
             1 - Peripheral
 	    2 - Host
 - qcom,hsusb-otg-phy-init-seq: PHY configuration sequence. val, reg pairs
   terminate with -1
 - qcom,hsusb-otg-power-budget: VBUS power budget in mA
   0 will be treated as 500mA
 - qcom,hsusb-otg-pclk-src-name: The source of pclk
 - qcom,hsusb-otg-pmic-id-irq: ID, routed to PMIC IRQ number
 - Refer to "Documentation/devicetree/bindings/arm/msm/msm_bus.txt" for
   below optional properties:
     - qcom,msm_bus,name
     - qcom,msm_bus,num_cases
     - qcom,msm_bus,active_only
     - qcom,msm_bus,num_paths
     - qcom,msm_bus,vectors
 - qcom,hsusb-otg-lpm-on-dev-suspend: If present then USB enter to
 	    low power mode upon receiving bus suspend.
 - qcom,hsusb-otg-clk-always-on-workaround: If present then USB core clocks
 	    remain active upon receiving bus suspend and USB cable is connected.
 	    Used for allowing USB to respond for remote wakup.
 - qcom,hsusb-otg-delay-lpm: If present then USB core will wait one second
 	after disconnect before entering low power mode.
 - <supply-name>-supply: handle to the regulator device tree node.
          Optional "supply-name" is "vbus_otg" to supply vbus in host mode.
 - qcom,vdd-voltage-level: This property must be a list of three integer
 	values (no, min, max) where each value represents either a voltage
 	in microvolts or a value corresponding to voltage corner.
 - qcom,dp-manual-pullup: If present, vbus is not routed to USB controller/phy
 	and controller driver therefore enables pull-up explicitly before
 	starting controller using usbcmd run/stop bit.

 Example HSUSB OTG controller device node :
 	usb@f9690000 {
 		compatible = "qcom,hsusb-otg";
 		reg = <0xf9690000 0x400>;
 		interrupts = <134>;
 		interrupt-names = "core_irq";

 		qcom,hsusb-otg-phy-type = <2>;
 		qcom,hsusb-otg-mode = <1>;
 		qcom,hsusb-otg-otg-control = <1>;
 		qcom,hsusb-otg-disable-reset;
 		qcom,hsusb-otg-pnoc-errata-fix;
 		qcom,hsusb-otg-default-mode = <2>;
 		qcom,hsusb-otg-phy-init-seq = <0x01 0x90 0xffffffff>;
 		qcom,hsusb-otg-power-budget = <500>;
 		qcom,hsusb-otg-pclk-src-name = "dfab_usb_clk";
 		qcom,hsusb-otg-pmic-id-irq = <47>
 		qcom,hsusb-otg-lpm-on-dev-suspend;
 		qcom,hsusb-otg-clk-always-on-workaround;
 		hsusb_vdd_dig-supply = <&pm8226_s1_corner>;
                 HSUSB_1p8-supply = <&pm8226_l10>;
                 HSUSB_3p3-supply = <&pm8226_l20>;
 		qcom,vdd-voltage-level = <1 5 7>;
 		qcom,dp-manual-pullup;
 		qcom,msm_bus,name = "usb2";
 		qcom,msm_bus,num_cases = <2>;
 		qcom,msm_bus,active_only = <0>;
 		qcom,msm_bus,num_paths = <1>;
 		qcom,msm_bus,vectors =
 				<87 512 0 0>,
 				<87 512 60000000 960000000>;
 	};

 MSM HSUSB EHCI controller

 Required properties :
 - compatible : should be "qcom,ehci-host"
 - reg : offset and length of the register set in the memory map
 - interrupts: IRQ lines used by this controller
 - interrupt-names : Required interrupt resource entries are:
             HSUSB EHCI expects "core_irq" and optionally "async_irq".
 - <supply-name>-supply: handle to the regulator device tree node
   Required "supply-name" is "HSUSB_VDDCX" "HSUSB_1p8-supply" "HSUSB_3p3-supply".
 - qcom,usb2-power-budget: maximum vbus power (in mA) that can be provided.

 Optional properties :
 - qcom,usb2-enable-hsphy2: If present, select second PHY for USB operation.
 - qcom,pool-64-bit-align: If present then the pool's memory will be aligned
   to 64 bits
 - qcom,enable_hbm: if present host bus manager is enabled.

 Example MSM HSUSB EHCI controller device node :
 	ehci: qcom,ehci-host@f9a55000 {
 		compatible = "qcom,ehci-host";
 		reg = <0xf9a55000 0x400>;
 		interrupts = <0 134 0>, <0 140 0>;
 		interrupt-names = "core_irq", "async_irq";
 		HSUSB_VDDCX-supply = <&pm8841_s2>;
 		HSUSB_1p8-supply = <&pm8941_l6>;
 		HSUSB_3p3-supply = <&pm8941_l24>;
 		qcom,usb2-enable-hsphy2;
 		qcom,usb2-power-budget = <500>;
 	};

 ANDROID USB:

 Required properties:
 - compatible: should be "qcom,android-usb"

 Optional properties :
 - reg  : offset and length of memory region that is used by device to
   update USB PID and serial numbers used by bootloader in DLOAD mode.
 - qcom,android-usb-swfi-latency : value to be used by device to vote
   for DMA latency in microsecs.

 Example Android USB device node :
 	android_usb@fc42b0c8 {
 		compatible = "qcom,android-usb";
 		reg = <0xfc42b0c8 0xc8>;
 		qcom,android-usb-swfi-latency = <1>;
 	};


 BAM:

 Required properties:
 - compatible: should be "qcom,usb-bam-msm"
 - reg  : pairs of physical base addresses and region sizes
             of all the memory mapped BAM devices present
 - reg-names : Register region name(s), in 1-1 correspondence with the
 	    registers in 'reg'. This list should contain at least as many names
             as the number of unique values given in both 'usb-active-bam' and
             all the subnodes' 'usb-bam-type' properties.

             If SSUSB_BAM is used, "ssusb" should be present.
             If HSUSB_BAM is used, "hsusb" should be present.
             If HSIC_BAM is used, "hsic" should be present.

             If a QSCRATCH RAM1 register is designated for providing USB3
             private memory to use as a BAM FIFO, specify "qscratch_ram1_reg".
 - interrupts: IRQ lines for BAM devices
 - interrupt-names: BAM interrupt name(s), in 1-1 correspondence with
             'interrupts' above.

             If SSUSB_BAM is used, "ssusb" should be present.
             If HSUSB_BAM is used, "hsusb" should be present.
             If HSIC_BAM is used, "hsic" should be present.
 - qcom,usb-bam-num-pipes: max number of pipes that can be used

 Optional properties:
 - qcom,usb-bam-fifo-baseaddr: base address for bam pipe's data and descriptor
   fifos. This can be on chip memory (ocimem) or usb private memory. This
   property is required if sub-node's mem-type is ocimem or usb private mem.

 A number of USB BAM pipe parameters are represented as sub-nodes:

 Subnode Required:
 - label: a string describing uniquely the usb bam pipe. The string can be
   constracted as follows: <core>-<peer>-<direction>-<pipe num>.
 	core options: hsusb, ssusb/dwc3, hsic
 	peer options: qdss, ipa, a2
 	direction options: in (from peer to usb), out (from usb to peer)
 	pipe num options: 0..127
 - qcom,usb-bam-mem-type: Type of memory used by this PIPE. Can be one of
             0 - Uses SPS's dedicated pipe memory
             1 - USB's private memory residing @ 'qcom,usb-bam-fifo-baseaddr'
             2 - System RAM allocated by driver
 	    3 - OCI memory residing @ 'qcom,usb-bam-fifo-baseaddr'
 - qcom,bam-type: BAM type can be one of
 	0 - SSUSB_BAM
 	1 - HSUSB_BAM
 	2 - HSIC_BAM
 - qcom,dir: pipe direction
 	0 - from usb (out)
 	1 - to usb (in)
 - qcom,pipe-num: pipe number
 - qcom,peer-bam: peer BAM can be one of
 	0 - A2_P_BAM
 	1 - QDSS_P_BAM
 	2 - IPA_P_BAM
 - qcom,data-fifo-size: data fifo size
 - qcom,descriptor-fifo-size: descriptor fifo size

 Optional Properties for Subnode:
 - qcom,reset-bam-on-connect: If present then BAM is RESET before connecting
   pipe. This may be required if BAM peripheral is also reset before connect.
 - qcom,dst-bam-physical-address: destination BAM physical address
 - qcom,dst-bam-pipe-index: destination BAM pipe index
 - qcom,src-bam-physical-address: source BAM physical address
 - qcom,src-bam-pipe-index: source BAM pipe index
 - qcom,data-fifo-offset: data fifo offset address
 - qcom,descriptor-fifo-offset: descriptor fifo offset address

 Optional properties :
 - qcom,ignore-core-reset-ack: If present then BAM ignores ACK from USB core
 	    while performing PIPE RESET
 - qcom,disable-clk-gating: If present then disable BAM clock gating.

 Example USB BAM controller device node:

 	qcom,usbbam@f9a44000 {
 		compatible = "qcom,usb-bam-msm";
 		reg = <0xf9a44000 0x11000>;
 		reg-names = "hsusb";
 		interrupts = <0 135 0>;
 		interrupt-names = "hsusb";
 		qcom,usb-bam-num-pipes = <16>;
 		qcom,ignore-core-reset-ack;
 		qcom,disable-clk-gating;

 		qcom,pipe0 {
 			label = "hsusb-ipa-out-0";
 			qcom,usb-bam-mem-type = <0>;
 			qcom,bam-type = <1>;
 			qcom,dir = <0>;
 			qcom,pipe-num = <0>;
 			qcom,peer-bam = <2>;
 			qcom,src-bam-physical-address = <0xf9a44000>;
 			qcom,src-bam-pipe-index = <1>;
 			qcom,data-fifo-offset = <0x2200>;
 			qcom,data-fifo-size = <0x1e00>;
 			qcom,descriptor-fifo-offset = <0x2100>;
 			qcom,descriptor-fifo-size = <0x100>;
 		};
 		qcom,pipe1 {
 			label = "hsusb-ipa-in-0";
 			qcom,usb-bam-mem-type = <0>;
 			qcom,bam-type = <1>;
 			qcom,dir = <1>;
 			qcom,pipe-num = <0>;
 			qcom,peer-bam = <2>;
 			qcom,dst-bam-physical-address = <0xf9a44000>;
 			qcom,dst-bam-pipe-index = <0>;
 			qcom,data-fifo-offset = <0x300>;
 			qcom,data-fifo-size = <0x1e00>;
 			qcom,descriptor-fifo-offset = <0>;
 			qcom,descriptor-fifo-size = <0x300>;
 		};
 	};
	MSM SoC HSUSB controllers

	OTG:

	Required properties :
	- compatible : should be "qcom,hsusb-otg"
	- regs : offset and length of the register set in the memory map
	- interrupts: IRQ line
	- interrupt-names: OTG interrupt name(s) referenced in interrupts above
	HSUSB OTG expects "core_irq" and optionally "async_irq".
	- qcom,hsusb-otg-phy-type: PHY type can be one of
	1 - Chipidea 45nm PHY
	2 - Synopsis 28nm PHY
	- qcom,hsusb-otg-mode: Operational mode. Can be one of
	1 - Peripheral only mode
	2 - Host only mode
	3 - OTG mode
	Based on the mode, OTG driver registers platform devices for
	gadget and host.
	- qcom,hsusb-otg-control: OTG control (VBUS and ID notifications)
	can be one of
	1 - PHY control
	2 - PMIC control
	3 - User control (via debugfs)
	- <supply-name>-supply: handle to the regulator device tree node
	Required "supply-name" is "HSUSB_VDDCX" (when voting for VDDCX) or
	"hsusb_vdd_dig" (when voting for VDDCX Corner voltage),
	"HSUSB_1p8-supply" and "HSUSB_3p3-supply".

	Optional properties :
	- qcom,hsusb-otg-disable-reset: If present then core is RESET only during
	init, otherwise core is RESET for every cable disconnect as well
	- qcom,hsusb-otg-pnoc-errata-fix: If present then workaround for PNOC
	performance issue is applied which requires changing the mem-type
	attribute via VMIDMT.
	- qcom,hsusb-otg-default-mode: The default USB mode after boot-up.
	Applicable only when OTG is controlled by user. Can be one of
	0 - None. Low power mode
	1 - Peripheral
	2 - Host
	- qcom,hsusb-otg-phy-init-seq: PHY configuration sequence. val, reg pairs
	terminate with -1
	- qcom,hsusb-otg-power-budget: VBUS power budget in mA
	0 will be treated as 500mA
	- qcom,hsusb-otg-pclk-src-name: The source of pclk
	- qcom,hsusb-otg-pmic-id-irq: ID, routed to PMIC IRQ number
	- Refer to "Documentation/devicetree/bindings/arm/msm/msm_bus.txt" for
	below optional properties:
	- qcom,msm_bus,name
	- qcom,msm_bus,num_cases
	- qcom,msm_bus,active_only
	- qcom,msm_bus,num_paths
	- qcom,msm_bus,vectors
	- qcom,hsusb-otg-lpm-on-dev-suspend: If present then USB enter to
	low power mode upon receiving bus suspend.
	- qcom,hsusb-otg-clk-always-on-workaround: If present then USB core clocks
	remain active upon receiving bus suspend and USB cable is connected.
	Used for allowing USB to respond for remote wakup.
	- qcom,hsusb-otg-delay-lpm: If present then USB core will wait one second
	after disconnect before entering low power mode.
	- <supply-name>-supply: handle to the regulator device tree node.
	Optional "supply-name" is "vbus_otg" to supply vbus in host mode.
	- qcom,vdd-voltage-level: This property must be a list of three integer
	values (no, min, max) where each value represents either a voltage
	in microvolts or a value corresponding to voltage corner.
	- qcom,dp-manual-pullup: If present, vbus is not routed to USB controller/phy
	and controller driver therefore enables pull-up explicitly before
	starting controller using usbcmd run/stop bit.

	Example HSUSB OTG controller device node :
	usb@f9690000 {
	compatible = "qcom,hsusb-otg";
	reg = <0xf9690000 0x400>;
	interrupts = <134>;
	interrupt-names = "core_irq";

	qcom,hsusb-otg-phy-type = <2>;
	qcom,hsusb-otg-mode = <1>;
	qcom,hsusb-otg-otg-control = <1>;
	qcom,hsusb-otg-disable-reset;
	qcom,hsusb-otg-pnoc-errata-fix;
	qcom,hsusb-otg-default-mode = <2>;
	qcom,hsusb-otg-phy-init-seq = <0x01 0x90 0xffffffff>;
	qcom,hsusb-otg-power-budget = <500>;
	qcom,hsusb-otg-pclk-src-name = "dfab_usb_clk";
	qcom,hsusb-otg-pmic-id-irq = <47>
	qcom,hsusb-otg-lpm-on-dev-suspend;
	qcom,hsusb-otg-clk-always-on-workaround;
	hsusb_vdd_dig-supply = <&pm8226_s1_corner>;
	HSUSB_1p8-supply = <&pm8226_l10>;
	HSUSB_3p3-supply = <&pm8226_l20>;
	qcom,vdd-voltage-level = <1 5 7>;
	qcom,dp-manual-pullup;
	qcom,msm_bus,name = "usb2";
	qcom,msm_bus,num_cases = <2>;
	qcom,msm_bus,active_only = <0>;
	qcom,msm_bus,num_paths = <1>;
	qcom,msm_bus,vectors =
	<87 512 0 0>,
	<87 512 60000000 960000000>;
	};

	MSM HSUSB EHCI controller

	Required properties :
	- compatible : should be "qcom,ehci-host"
	- reg : offset and length of the register set in the memory map
	- interrupts: IRQ lines used by this controller
	- interrupt-names : Required interrupt resource entries are:
	HSUSB EHCI expects "core_irq" and optionally "async_irq".
	- <supply-name>-supply: handle to the regulator device tree node
	Required "supply-name" is "HSUSB_VDDCX" "HSUSB_1p8-supply" "HSUSB_3p3-supply".
	- qcom,usb2-power-budget: maximum vbus power (in mA) that can be provided.

	Optional properties :
	- qcom,usb2-enable-hsphy2: If present, select second PHY for USB operation.
	- qcom,pool-64-bit-align: If present then the pool's memory will be aligned
	to 64 bits
	- qcom,enable_hbm: if present host bus manager is enabled.

	Example MSM HSUSB EHCI controller device node :
	ehci: qcom,ehci-host@f9a55000 {
	compatible = "qcom,ehci-host";
	reg = <0xf9a55000 0x400>;
	interrupts = <0 134 0>, <0 140 0>;
	interrupt-names = "core_irq", "async_irq";
	HSUSB_VDDCX-supply = <&pm8841_s2>;
	HSUSB_1p8-supply = <&pm8941_l6>;
	HSUSB_3p3-supply = <&pm8941_l24>;
	qcom,usb2-enable-hsphy2;
	qcom,usb2-power-budget = <500>;
	};

	ANDROID USB:

	Required properties:
	- compatible: should be "qcom,android-usb"

	Optional properties :
	- reg : offset and length of memory region that is used by device to
	update USB PID and serial numbers used by bootloader in DLOAD mode.
	- qcom,android-usb-swfi-latency : value to be used by device to vote
	for DMA latency in microsecs.

	Example Android USB device node :
	android_usb@fc42b0c8 {
	compatible = "qcom,android-usb";
	reg = <0xfc42b0c8 0xc8>;
	qcom,android-usb-swfi-latency = <1>;
	};


	BAM:

	Required properties:
	- compatible: should be "qcom,usb-bam-msm"
	- reg : pairs of physical base addresses and region sizes
	of all the memory mapped BAM devices present
	- reg-names : Register region name(s), in 1-1 correspondence with the
	registers in 'reg'. This list should contain at least as many names
	as the number of unique values given in both 'usb-active-bam' and
	all the subnodes' 'usb-bam-type' properties.

	If SSUSB_BAM is used, "ssusb" should be present.
	If HSUSB_BAM is used, "hsusb" should be present.
	If HSIC_BAM is used, "hsic" should be present.

	If a QSCRATCH RAM1 register is designated for providing USB3
	private memory to use as a BAM FIFO, specify "qscratch_ram1_reg".
	- interrupts: IRQ lines for BAM devices
	- interrupt-names: BAM interrupt name(s), in 1-1 correspondence with
	'interrupts' above.

	If SSUSB_BAM is used, "ssusb" should be present.
	If HSUSB_BAM is used, "hsusb" should be present.
	If HSIC_BAM is used, "hsic" should be present.
	- qcom,usb-bam-num-pipes: max number of pipes that can be used

	Optional properties:
	- qcom,usb-bam-fifo-baseaddr: base address for bam pipe's data and descriptor
	fifos. This can be on chip memory (ocimem) or usb private memory. This
	property is required if sub-node's mem-type is ocimem or usb private mem.

	A number of USB BAM pipe parameters are represented as sub-nodes:

	Subnode Required:
	- label: a string describing uniquely the usb bam pipe. The string can be
	constracted as follows: <core>-<peer>-<direction>-<pipe num>.
	core options: hsusb, ssusb/dwc3, hsic
	peer options: qdss, ipa, a2
	direction options: in (from peer to usb), out (from usb to peer)
	pipe num options: 0..127
	- qcom,usb-bam-mem-type: Type of memory used by this PIPE. Can be one of
	0 - Uses SPS's dedicated pipe memory
	1 - USB's private memory residing @ 'qcom,usb-bam-fifo-baseaddr'
	2 - System RAM allocated by driver
	3 - OCI memory residing @ 'qcom,usb-bam-fifo-baseaddr'
	- qcom,bam-type: BAM type can be one of
	0 - SSUSB_BAM
	1 - HSUSB_BAM
	2 - HSIC_BAM
	- qcom,dir: pipe direction
	0 - from usb (out)
	1 - to usb (in)
	- qcom,pipe-num: pipe number
	- qcom,peer-bam: peer BAM can be one of
	0 - A2_P_BAM
	1 - QDSS_P_BAM
	2 - IPA_P_BAM
	- qcom,data-fifo-size: data fifo size
	- qcom,descriptor-fifo-size: descriptor fifo size

	Optional Properties for Subnode:
	- qcom,reset-bam-on-connect: If present then BAM is RESET before connecting
	pipe. This may be required if BAM peripheral is also reset before connect.
	- qcom,dst-bam-physical-address: destination BAM physical address
	- qcom,dst-bam-pipe-index: destination BAM pipe index
	- qcom,src-bam-physical-address: source BAM physical address
	- qcom,src-bam-pipe-index: source BAM pipe index
	- qcom,data-fifo-offset: data fifo offset address
	- qcom,descriptor-fifo-offset: descriptor fifo offset address

	Optional properties :
	- qcom,ignore-core-reset-ack: If present then BAM ignores ACK from USB core
	while performing PIPE RESET
	- qcom,disable-clk-gating: If present then disable BAM clock gating.

	Example USB BAM controller device node:

	qcom,usbbam@f9a44000 {
	compatible = "qcom,usb-bam-msm";
	reg = <0xf9a44000 0x11000>;
	reg-names = "hsusb";
	interrupts = <0 135 0>;
	interrupt-names = "hsusb";
	qcom,usb-bam-num-pipes = <16>;
	qcom,ignore-core-reset-ack;
	qcom,disable-clk-gating;

	qcom,pipe0 {
	label = "hsusb-ipa-out-0";
	qcom,usb-bam-mem-type = <0>;
	qcom,bam-type = <1>;
	qcom,dir = <0>;
	qcom,pipe-num = <0>;
	qcom,peer-bam = <2>;
	qcom,src-bam-physical-address = <0xf9a44000>;
	qcom,src-bam-pipe-index = <1>;
	qcom,data-fifo-offset = <0x2200>;
	qcom,data-fifo-size = <0x1e00>;
	qcom,descriptor-fifo-offset = <0x2100>;
	qcom,descriptor-fifo-size = <0x100>;
	};
	qcom,pipe1 {
	label = "hsusb-ipa-in-0";
	qcom,usb-bam-mem-type = <0>;
	qcom,bam-type = <1>;
	qcom,dir = <1>;
	qcom,pipe-num = <0>;
	qcom,peer-bam = <2>;
	qcom,dst-bam-physical-address = <0xf9a44000>;
	qcom,dst-bam-pipe-index = <0>;
	qcom,data-fifo-offset = <0x300>;
	qcom,data-fifo-size = <0x1e00>;
	qcom,descriptor-fifo-offset = <0>;
	qcom,descriptor-fifo-size = <0x300>;
	};
	};