| /*====================================================================== |
| |
| A driver for PCMCIA serial devices |
| |
| serial_cs.c 1.134 2002/05/04 05:48:53 |
| |
| The contents of this file are subject to the Mozilla Public |
| License Version 1.1 (the "License"); you may not use this file |
| except in compliance with the License. You may obtain a copy of |
| the License at http://www.mozilla.org/MPL/ |
| |
| Software distributed under the License is distributed on an "AS |
| IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or |
| implied. See the License for the specific language governing |
| rights and limitations under the License. |
| |
| The initial developer of the original code is David A. Hinds |
| <dahinds@users.sourceforge.net>. Portions created by David A. Hinds |
| are Copyright (C) 1999 David A. Hinds. All Rights Reserved. |
| |
| Alternatively, the contents of this file may be used under the |
| terms of the GNU General Public License version 2 (the "GPL"), in which |
| case the provisions of the GPL are applicable instead of the |
| above. If you wish to allow the use of your version of this file |
| only under the terms of the GPL and not to allow others to use |
| your version of this file under the MPL, indicate your decision |
| by deleting the provisions above and replace them with the notice |
| and other provisions required by the GPL. If you do not delete |
| the provisions above, a recipient may use your version of this |
| file under either the MPL or the GPL. |
| |
| ======================================================================*/ |
| |
| #include <linux/module.h> |
| #include <linux/moduleparam.h> |
| #include <linux/kernel.h> |
| #include <linux/init.h> |
| #include <linux/ptrace.h> |
| #include <linux/slab.h> |
| #include <linux/string.h> |
| #include <linux/timer.h> |
| #include <linux/serial_core.h> |
| #include <linux/delay.h> |
| #include <linux/major.h> |
| #include <asm/io.h> |
| #include <asm/system.h> |
| |
| #include <pcmcia/cs_types.h> |
| #include <pcmcia/cs.h> |
| #include <pcmcia/cistpl.h> |
| #include <pcmcia/ciscode.h> |
| #include <pcmcia/ds.h> |
| #include <pcmcia/cisreg.h> |
| |
| #include "8250.h" |
| |
| |
| /*====================================================================*/ |
| |
| /* Parameters that can be set with 'insmod' */ |
| |
| /* Enable the speaker? */ |
| static int do_sound = 1; |
| /* Skip strict UART tests? */ |
| static int buggy_uart; |
| |
| module_param(do_sound, int, 0444); |
| module_param(buggy_uart, int, 0444); |
| |
| /*====================================================================*/ |
| |
| /* Table of multi-port card ID's */ |
| |
| struct serial_quirk { |
| unsigned int manfid; |
| unsigned int prodid; |
| int multi; /* 1 = multifunction, > 1 = # ports */ |
| void (*config)(struct pcmcia_device *); |
| void (*setup)(struct pcmcia_device *, struct uart_port *); |
| void (*wakeup)(struct pcmcia_device *); |
| int (*post)(struct pcmcia_device *); |
| }; |
| |
| struct serial_info { |
| struct pcmcia_device *p_dev; |
| int ndev; |
| int multi; |
| int slave; |
| int manfid; |
| int prodid; |
| int c950ctrl; |
| dev_node_t node[4]; |
| int line[4]; |
| const struct serial_quirk *quirk; |
| }; |
| |
| struct serial_cfg_mem { |
| tuple_t tuple; |
| cisparse_t parse; |
| u_char buf[256]; |
| }; |
| |
| /* |
| * vers_1 5.0, "Brain Boxes", "2-Port RS232 card", "r6" |
| * manfid 0x0160, 0x0104 |
| * This card appears to have a 14.7456MHz clock. |
| */ |
| static void quirk_setup_brainboxes_0104(struct pcmcia_device *link, struct uart_port *port) |
| { |
| port->uartclk = 14745600; |
| } |
| |
| static int quirk_post_ibm(struct pcmcia_device *link) |
| { |
| conf_reg_t reg = { 0, CS_READ, 0x800, 0 }; |
| int ret; |
| |
| ret = pcmcia_access_configuration_register(link, ®); |
| if (ret) |
| goto failed; |
| |
| reg.Action = CS_WRITE; |
| reg.Value = reg.Value | 1; |
| ret = pcmcia_access_configuration_register(link, ®); |
| if (ret) |
| goto failed; |
| return 0; |
| |
| failed: |
| return -ENODEV; |
| } |
| |
| /* |
| * Nokia cards are not really multiport cards. Shouldn't this |
| * be handled by setting the quirk entry .multi = 0 | 1 ? |
| */ |
| static void quirk_config_nokia(struct pcmcia_device *link) |
| { |
| struct serial_info *info = link->priv; |
| |
| if (info->multi > 1) |
| info->multi = 1; |
| } |
| |
| static void quirk_wakeup_oxsemi(struct pcmcia_device *link) |
| { |
| struct serial_info *info = link->priv; |
| |
| outb(12, info->c950ctrl + 1); |
| } |
| |
| /* request_region? oxsemi branch does no request_region too... */ |
| /* |
| * This sequence is needed to properly initialize MC45 attached to OXCF950. |
| * I tried decreasing these msleep()s, but it worked properly (survived |
| * 1000 stop/start operations) with these timeouts (or bigger). |
| */ |
| static void quirk_wakeup_possio_gcc(struct pcmcia_device *link) |
| { |
| struct serial_info *info = link->priv; |
| unsigned int ctrl = info->c950ctrl; |
| |
| outb(0xA, ctrl + 1); |
| msleep(100); |
| outb(0xE, ctrl + 1); |
| msleep(300); |
| outb(0xC, ctrl + 1); |
| msleep(100); |
| outb(0xE, ctrl + 1); |
| msleep(200); |
| outb(0xF, ctrl + 1); |
| msleep(100); |
| outb(0xE, ctrl + 1); |
| msleep(100); |
| outb(0xC, ctrl + 1); |
| } |
| |
| /* |
| * Socket Dual IO: this enables irq's for second port |
| */ |
| static void quirk_config_socket(struct pcmcia_device *link) |
| { |
| struct serial_info *info = link->priv; |
| |
| if (info->multi) { |
| link->conf.Present |= PRESENT_EXT_STATUS; |
| link->conf.ExtStatus = ESR_REQ_ATTN_ENA; |
| } |
| } |
| |
| static const struct serial_quirk quirks[] = { |
| { |
| .manfid = 0x0160, |
| .prodid = 0x0104, |
| .multi = -1, |
| .setup = quirk_setup_brainboxes_0104, |
| }, { |
| .manfid = MANFID_IBM, |
| .prodid = ~0, |
| .multi = -1, |
| .post = quirk_post_ibm, |
| }, { |
| .manfid = MANFID_INTEL, |
| .prodid = PRODID_INTEL_DUAL_RS232, |
| .multi = 2, |
| }, { |
| .manfid = MANFID_NATINST, |
| .prodid = PRODID_NATINST_QUAD_RS232, |
| .multi = 4, |
| }, { |
| .manfid = MANFID_NOKIA, |
| .prodid = ~0, |
| .multi = -1, |
| .config = quirk_config_nokia, |
| }, { |
| .manfid = MANFID_OMEGA, |
| .prodid = PRODID_OMEGA_QSP_100, |
| .multi = 4, |
| }, { |
| .manfid = MANFID_OXSEMI, |
| .prodid = ~0, |
| .multi = -1, |
| .wakeup = quirk_wakeup_oxsemi, |
| }, { |
| .manfid = MANFID_POSSIO, |
| .prodid = PRODID_POSSIO_GCC, |
| .multi = -1, |
| .wakeup = quirk_wakeup_possio_gcc, |
| }, { |
| .manfid = MANFID_QUATECH, |
| .prodid = PRODID_QUATECH_DUAL_RS232, |
| .multi = 2, |
| }, { |
| .manfid = MANFID_QUATECH, |
| .prodid = PRODID_QUATECH_DUAL_RS232_D1, |
| .multi = 2, |
| }, { |
| .manfid = MANFID_QUATECH, |
| .prodid = PRODID_QUATECH_DUAL_RS232_G, |
| .multi = 2, |
| }, { |
| .manfid = MANFID_QUATECH, |
| .prodid = PRODID_QUATECH_QUAD_RS232, |
| .multi = 4, |
| }, { |
| .manfid = MANFID_SOCKET, |
| .prodid = PRODID_SOCKET_DUAL_RS232, |
| .multi = 2, |
| .config = quirk_config_socket, |
| }, { |
| .manfid = MANFID_SOCKET, |
| .prodid = ~0, |
| .multi = -1, |
| .config = quirk_config_socket, |
| } |
| }; |
| |
| |
| static int serial_config(struct pcmcia_device * link); |
| |
| |
| /*====================================================================== |
| |
| After a card is removed, serial_remove() will unregister |
| the serial device(s), and release the PCMCIA configuration. |
| |
| ======================================================================*/ |
| |
| static void serial_remove(struct pcmcia_device *link) |
| { |
| struct serial_info *info = link->priv; |
| int i; |
| |
| dev_dbg(&link->dev, "serial_release\n"); |
| |
| /* |
| * Recheck to see if the device is still configured. |
| */ |
| for (i = 0; i < info->ndev; i++) |
| serial8250_unregister_port(info->line[i]); |
| |
| info->p_dev->dev_node = NULL; |
| |
| if (!info->slave) |
| pcmcia_disable_device(link); |
| } |
| |
| static int serial_suspend(struct pcmcia_device *link) |
| { |
| struct serial_info *info = link->priv; |
| int i; |
| |
| for (i = 0; i < info->ndev; i++) |
| serial8250_suspend_port(info->line[i]); |
| |
| return 0; |
| } |
| |
| static int serial_resume(struct pcmcia_device *link) |
| { |
| struct serial_info *info = link->priv; |
| int i; |
| |
| for (i = 0; i < info->ndev; i++) |
| serial8250_resume_port(info->line[i]); |
| |
| if (info->quirk && info->quirk->wakeup) |
| info->quirk->wakeup(link); |
| |
| return 0; |
| } |
| |
| /*====================================================================== |
| |
| serial_attach() creates an "instance" of the driver, allocating |
| local data structures for one device. The device is registered |
| with Card Services. |
| |
| ======================================================================*/ |
| |
| static int serial_probe(struct pcmcia_device *link) |
| { |
| struct serial_info *info; |
| |
| dev_dbg(&link->dev, "serial_attach()\n"); |
| |
| /* Create new serial device */ |
| info = kzalloc(sizeof (*info), GFP_KERNEL); |
| if (!info) |
| return -ENOMEM; |
| info->p_dev = link; |
| link->priv = info; |
| |
| link->io.Attributes1 = IO_DATA_PATH_WIDTH_8; |
| link->io.NumPorts1 = 8; |
| link->irq.Attributes = IRQ_TYPE_DYNAMIC_SHARING; |
| link->conf.Attributes = CONF_ENABLE_IRQ; |
| if (do_sound) { |
| link->conf.Attributes |= CONF_ENABLE_SPKR; |
| link->conf.Status = CCSR_AUDIO_ENA; |
| } |
| link->conf.IntType = INT_MEMORY_AND_IO; |
| |
| return serial_config(link); |
| } |
| |
| /*====================================================================== |
| |
| This deletes a driver "instance". The device is de-registered |
| with Card Services. If it has been released, all local data |
| structures are freed. Otherwise, the structures will be freed |
| when the device is released. |
| |
| ======================================================================*/ |
| |
| static void serial_detach(struct pcmcia_device *link) |
| { |
| struct serial_info *info = link->priv; |
| |
| dev_dbg(&link->dev, "serial_detach\n"); |
| |
| /* |
| * Ensure any outstanding scheduled tasks are completed. |
| */ |
| flush_scheduled_work(); |
| |
| /* |
| * Ensure that the ports have been released. |
| */ |
| serial_remove(link); |
| |
| /* free bits */ |
| kfree(info); |
| } |
| |
| /*====================================================================*/ |
| |
| static int setup_serial(struct pcmcia_device *handle, struct serial_info * info, |
| unsigned int iobase, int irq) |
| { |
| struct uart_port port; |
| int line; |
| |
| memset(&port, 0, sizeof (struct uart_port)); |
| port.iobase = iobase; |
| port.irq = irq; |
| port.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_SHARE_IRQ; |
| port.uartclk = 1843200; |
| port.dev = &handle->dev; |
| if (buggy_uart) |
| port.flags |= UPF_BUGGY_UART; |
| |
| if (info->quirk && info->quirk->setup) |
| info->quirk->setup(handle, &port); |
| |
| line = serial8250_register_port(&port); |
| if (line < 0) { |
| printk(KERN_NOTICE "serial_cs: serial8250_register_port() at " |
| "0x%04lx, irq %d failed\n", (u_long)iobase, irq); |
| return -EINVAL; |
| } |
| |
| info->line[info->ndev] = line; |
| sprintf(info->node[info->ndev].dev_name, "ttyS%d", line); |
| info->node[info->ndev].major = TTY_MAJOR; |
| info->node[info->ndev].minor = 0x40 + line; |
| if (info->ndev > 0) |
| info->node[info->ndev - 1].next = &info->node[info->ndev]; |
| info->ndev++; |
| |
| return 0; |
| } |
| |
| /*====================================================================*/ |
| |
| static int simple_config_check(struct pcmcia_device *p_dev, |
| cistpl_cftable_entry_t *cf, |
| cistpl_cftable_entry_t *dflt, |
| unsigned int vcc, |
| void *priv_data) |
| { |
| static const int size_table[2] = { 8, 16 }; |
| int *try = priv_data; |
| |
| if (cf->vpp1.present & (1 << CISTPL_POWER_VNOM)) |
| p_dev->conf.Vpp = |
| cf->vpp1.param[CISTPL_POWER_VNOM] / 10000; |
| |
| if ((cf->io.nwin > 0) && (cf->io.win[0].len == size_table[(*try >> 1)]) |
| && (cf->io.win[0].base != 0)) { |
| p_dev->io.BasePort1 = cf->io.win[0].base; |
| p_dev->io.IOAddrLines = ((*try & 0x1) == 0) ? |
| 16 : cf->io.flags & CISTPL_IO_LINES_MASK; |
| if (!pcmcia_request_io(p_dev, &p_dev->io)) |
| return 0; |
| } |
| return -EINVAL; |
| } |
| |
| static int simple_config_check_notpicky(struct pcmcia_device *p_dev, |
| cistpl_cftable_entry_t *cf, |
| cistpl_cftable_entry_t *dflt, |
| unsigned int vcc, |
| void *priv_data) |
| { |
| static const unsigned int base[5] = { 0x3f8, 0x2f8, 0x3e8, 0x2e8, 0x0 }; |
| int j; |
| |
| if ((cf->io.nwin > 0) && ((cf->io.flags & CISTPL_IO_LINES_MASK) <= 3)) { |
| for (j = 0; j < 5; j++) { |
| p_dev->io.BasePort1 = base[j]; |
| p_dev->io.IOAddrLines = base[j] ? 16 : 3; |
| if (!pcmcia_request_io(p_dev, &p_dev->io)) |
| return 0; |
| } |
| } |
| return -ENODEV; |
| } |
| |
| static int simple_config(struct pcmcia_device *link) |
| { |
| struct serial_info *info = link->priv; |
| int i = -ENODEV, try; |
| |
| /* If the card is already configured, look up the port and irq */ |
| if (link->function_config) { |
| unsigned int port = 0; |
| if ((link->io.BasePort2 != 0) && |
| (link->io.NumPorts2 == 8)) { |
| port = link->io.BasePort2; |
| info->slave = 1; |
| } else if ((info->manfid == MANFID_OSITECH) && |
| (link->io.NumPorts1 == 0x40)) { |
| port = link->io.BasePort1 + 0x28; |
| info->slave = 1; |
| } |
| if (info->slave) { |
| return setup_serial(link, info, port, |
| link->irq.AssignedIRQ); |
| } |
| } |
| |
| /* First pass: look for a config entry that looks normal. |
| * Two tries: without IO aliases, then with aliases */ |
| for (try = 0; try < 4; try++) |
| if (!pcmcia_loop_config(link, simple_config_check, &try)) |
| goto found_port; |
| |
| /* Second pass: try to find an entry that isn't picky about |
| its base address, then try to grab any standard serial port |
| address, and finally try to get any free port. */ |
| if (!pcmcia_loop_config(link, simple_config_check_notpicky, NULL)) |
| goto found_port; |
| |
| printk(KERN_NOTICE |
| "serial_cs: no usable port range found, giving up\n"); |
| return -1; |
| |
| found_port: |
| i = pcmcia_request_irq(link, &link->irq); |
| if (i != 0) |
| link->irq.AssignedIRQ = 0; |
| |
| if (info->multi && (info->manfid == MANFID_3COM)) |
| link->conf.ConfigIndex &= ~(0x08); |
| |
| /* |
| * Apply any configuration quirks. |
| */ |
| if (info->quirk && info->quirk->config) |
| info->quirk->config(link); |
| |
| i = pcmcia_request_configuration(link, &link->conf); |
| if (i != 0) |
| return -1; |
| return setup_serial(link, info, link->io.BasePort1, link->irq.AssignedIRQ); |
| } |
| |
| static int multi_config_check(struct pcmcia_device *p_dev, |
| cistpl_cftable_entry_t *cf, |
| cistpl_cftable_entry_t *dflt, |
| unsigned int vcc, |
| void *priv_data) |
| { |
| int *base2 = priv_data; |
| |
| /* The quad port cards have bad CIS's, so just look for a |
| window larger than 8 ports and assume it will be right */ |
| if ((cf->io.nwin == 1) && (cf->io.win[0].len > 8)) { |
| p_dev->io.BasePort1 = cf->io.win[0].base; |
| p_dev->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK; |
| if (!pcmcia_request_io(p_dev, &p_dev->io)) { |
| *base2 = p_dev->io.BasePort1 + 8; |
| return 0; |
| } |
| } |
| return -ENODEV; |
| } |
| |
| static int multi_config_check_notpicky(struct pcmcia_device *p_dev, |
| cistpl_cftable_entry_t *cf, |
| cistpl_cftable_entry_t *dflt, |
| unsigned int vcc, |
| void *priv_data) |
| { |
| int *base2 = priv_data; |
| |
| if (cf->io.nwin == 2) { |
| p_dev->io.BasePort1 = cf->io.win[0].base; |
| p_dev->io.BasePort2 = cf->io.win[1].base; |
| p_dev->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK; |
| if (!pcmcia_request_io(p_dev, &p_dev->io)) { |
| *base2 = p_dev->io.BasePort2; |
| return 0; |
| } |
| } |
| return -ENODEV; |
| } |
| |
| static int multi_config(struct pcmcia_device *link) |
| { |
| struct serial_info *info = link->priv; |
| int i, base2 = 0; |
| |
| /* First, look for a generic full-sized window */ |
| link->io.NumPorts1 = info->multi * 8; |
| if (pcmcia_loop_config(link, multi_config_check, &base2)) { |
| /* If that didn't work, look for two windows */ |
| link->io.NumPorts1 = link->io.NumPorts2 = 8; |
| info->multi = 2; |
| if (pcmcia_loop_config(link, multi_config_check_notpicky, |
| &base2)) { |
| printk(KERN_NOTICE "serial_cs: no usable port range" |
| "found, giving up\n"); |
| return -ENODEV; |
| } |
| } |
| |
| i = pcmcia_request_irq(link, &link->irq); |
| if (i != 0) { |
| /* FIXME: comment does not fit, error handling does not fit */ |
| printk(KERN_NOTICE |
| "serial_cs: no usable port range found, giving up\n"); |
| link->irq.AssignedIRQ = 0; |
| } |
| |
| /* |
| * Apply any configuration quirks. |
| */ |
| if (info->quirk && info->quirk->config) |
| info->quirk->config(link); |
| |
| i = pcmcia_request_configuration(link, &link->conf); |
| if (i != 0) |
| return -ENODEV; |
| |
| /* The Oxford Semiconductor OXCF950 cards are in fact single-port: |
| * 8 registers are for the UART, the others are extra registers. |
| * Siemen's MC45 PCMCIA (Possio's GCC) is OXCF950 based too. |
| */ |
| if (info->manfid == MANFID_OXSEMI || (info->manfid == MANFID_POSSIO && |
| info->prodid == PRODID_POSSIO_GCC)) { |
| int err; |
| |
| if (link->conf.ConfigIndex == 1 || |
| link->conf.ConfigIndex == 3) { |
| err = setup_serial(link, info, base2, |
| link->irq.AssignedIRQ); |
| base2 = link->io.BasePort1; |
| } else { |
| err = setup_serial(link, info, link->io.BasePort1, |
| link->irq.AssignedIRQ); |
| } |
| info->c950ctrl = base2; |
| |
| /* |
| * FIXME: We really should wake up the port prior to |
| * handing it over to the serial layer. |
| */ |
| if (info->quirk && info->quirk->wakeup) |
| info->quirk->wakeup(link); |
| |
| return 0; |
| } |
| |
| setup_serial(link, info, link->io.BasePort1, link->irq.AssignedIRQ); |
| for (i = 0; i < info->multi - 1; i++) |
| setup_serial(link, info, base2 + (8 * i), |
| link->irq.AssignedIRQ); |
| return 0; |
| } |
| |
| static int serial_check_for_multi(struct pcmcia_device *p_dev, |
| cistpl_cftable_entry_t *cf, |
| cistpl_cftable_entry_t *dflt, |
| unsigned int vcc, |
| void *priv_data) |
| { |
| struct serial_info *info = p_dev->priv; |
| |
| if ((cf->io.nwin == 1) && (cf->io.win[0].len % 8 == 0)) |
| info->multi = cf->io.win[0].len >> 3; |
| |
| if ((cf->io.nwin == 2) && (cf->io.win[0].len == 8) && |
| (cf->io.win[1].len == 8)) |
| info->multi = 2; |
| |
| return 0; /* break */ |
| } |
| |
| |
| /*====================================================================== |
| |
| serial_config() is scheduled to run after a CARD_INSERTION event |
| is received, to configure the PCMCIA socket, and to make the |
| serial device available to the system. |
| |
| ======================================================================*/ |
| |
| static int serial_config(struct pcmcia_device * link) |
| { |
| struct serial_info *info = link->priv; |
| int i; |
| |
| dev_dbg(&link->dev, "serial_config\n"); |
| |
| /* Is this a compliant multifunction card? */ |
| info->multi = (link->socket->functions > 1); |
| |
| /* Is this a multiport card? */ |
| info->manfid = link->manf_id; |
| info->prodid = link->card_id; |
| |
| for (i = 0; i < ARRAY_SIZE(quirks); i++) |
| if ((quirks[i].manfid == ~0 || |
| quirks[i].manfid == info->manfid) && |
| (quirks[i].prodid == ~0 || |
| quirks[i].prodid == info->prodid)) { |
| info->quirk = &quirks[i]; |
| break; |
| } |
| |
| /* Another check for dual-serial cards: look for either serial or |
| multifunction cards that ask for appropriate IO port ranges */ |
| if ((info->multi == 0) && |
| (link->has_func_id) && |
| ((link->func_id == CISTPL_FUNCID_MULTI) || |
| (link->func_id == CISTPL_FUNCID_SERIAL))) |
| pcmcia_loop_config(link, serial_check_for_multi, info); |
| |
| /* |
| * Apply any multi-port quirk. |
| */ |
| if (info->quirk && info->quirk->multi != -1) |
| info->multi = info->quirk->multi; |
| |
| if (info->multi > 1) |
| multi_config(link); |
| else |
| simple_config(link); |
| |
| if (info->ndev == 0) |
| goto failed; |
| |
| /* |
| * Apply any post-init quirk. FIXME: This should really happen |
| * before we register the port, since it might already be in use. |
| */ |
| if (info->quirk && info->quirk->post) |
| if (info->quirk->post(link)) |
| goto failed; |
| |
| link->dev_node = &info->node[0]; |
| return 0; |
| |
| failed: |
| serial_remove(link); |
| return -ENODEV; |
| } |
| |
| static struct pcmcia_device_id serial_ids[] = { |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0057, 0x0021), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0089, 0x110a), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0104, 0x000a), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0xea15), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0109, 0x0501), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0138, 0x110a), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0140, 0x000a), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0143, 0x3341), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0143, 0xc0ab), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x016c, 0x0081), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x021b, 0x0101), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x08a1, 0xc0ab), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0x0d0a), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0105, 0x0e0a), |
| PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "CC/XJEM3288", "DATA/FAX/CELL ETHERNET MODEM", 0xf510db04, 0x04cd2988, 0x46a52d63), |
| PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "CC/XJEM3336", "DATA/FAX/CELL ETHERNET MODEM", 0xf510db04, 0x0143b773, 0x46a52d63), |
| PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "EM1144T", "PCMCIA MODEM", 0xf510db04, 0x856d66c8, 0xbd6c43ef), |
| PCMCIA_PFC_DEVICE_PROD_ID123(1, "MEGAHERTZ", "XJEM1144/CCEM1144", "PCMCIA MODEM", 0xf510db04, 0x52d21e1e, 0xbd6c43ef), |
| PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM28", 0x2e3ee845, 0x0ea978ea), |
| PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM33", 0x2e3ee845, 0x80609023), |
| PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "CEM56", 0x2e3ee845, 0xa650c32a), |
| PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "REM10", 0x2e3ee845, 0x76df1d29), |
| PCMCIA_PFC_DEVICE_PROD_ID13(1, "Xircom", "XEM5600", 0x2e3ee845, 0xf1403719), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "AnyCom", "Fast Ethernet + 56K COMBO", 0x578ba6e7, 0xb0ac62c4), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "D-Link", "DME336T", 0x1a424a1c, 0xb23897ff), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "Gateway 2000", "XJEM3336", 0xdd9989be, 0x662c394c), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "Grey Cell", "GCS3000", 0x2a151fac, 0x48b932ae), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "Linksys", "EtherFast 10&100 + 56K PC Card (PCMLM56)", 0x0733cc81, 0xb3765033), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "LINKSYS", "PCMLM336", 0xf7cb0b07, 0x7a821b58), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "MEGAHERTZ", "XJEM1144/CCEM1144", 0xf510db04, 0x52d21e1e), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "MICRO RESEARCH", "COMBO-L/M-336", 0xb2ced065, 0x3ced0555), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "NEC", "PK-UG-J001" ,0x18df0ba0 ,0x831b1064), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "Ositech", "Trumpcard:Jack of Diamonds Modem+Ethernet", 0xc2f80cd, 0x656947b9), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "Ositech", "Trumpcard:Jack of Hearts Modem+Ethernet", 0xc2f80cd, 0xdc9ba5ed), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "PCMCIAs", "ComboCard", 0xdcfe12d3, 0xcd8906cc), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "PCMCIAs", "LanModem", 0xdcfe12d3, 0xc67c648f), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "TDK", "GlobalNetworker 3410/3412", 0x1eae9475, 0xd9a93bed), |
| PCMCIA_PFC_DEVICE_PROD_ID12(1, "Xircom", "CreditCard Ethernet+Modem II", 0x2e3ee845, 0xeca401bf), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x0a05), |
| PCMCIA_PFC_DEVICE_MANF_CARD(1, 0x0032, 0x1101), |
| PCMCIA_MFC_DEVICE_MANF_CARD(0, 0x0104, 0x0070), |
| PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0101, 0x0562), |
| PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0104, 0x0070), |
| PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x016c, 0x0020), |
| PCMCIA_MFC_DEVICE_PROD_ID123(1, "APEX DATA", "MULTICARD", "ETHERNET-MODEM", 0x11c2da09, 0x7289dc5d, 0xaad95e1f), |
| PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "Home and Away 28.8 PC Card ", 0xb569a6e5, 0x5bd4ff2c), |
| PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "Home and Away Credit Card Adapter", 0xb569a6e5, 0x4bdf15c3), |
| PCMCIA_MFC_DEVICE_PROD_ID12(1, "IBM", "w95 Home and Away Credit Card ", 0xb569a6e5, 0xae911c15), |
| PCMCIA_MFC_DEVICE_PROD_ID1(1, "Motorola MARQUIS", 0xf03e4e77), |
| PCMCIA_MFC_DEVICE_PROD_ID2(1, "FAX/Modem/Ethernet Combo Card ", 0x1ed59302), |
| PCMCIA_DEVICE_MANF_CARD(0x0089, 0x0301), |
| PCMCIA_DEVICE_MANF_CARD(0x00a4, 0x0276), |
| PCMCIA_DEVICE_MANF_CARD(0x0101, 0x0039), |
| PCMCIA_DEVICE_MANF_CARD(0x0104, 0x0006), |
| PCMCIA_DEVICE_MANF_CARD(0x0105, 0x410a), |
| PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d50), |
| PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d51), |
| PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d52), |
| PCMCIA_DEVICE_MANF_CARD(0x010b, 0x0d53), |
| PCMCIA_DEVICE_MANF_CARD(0x010b, 0xd180), |
| PCMCIA_DEVICE_MANF_CARD(0x0137, 0x000e), |
| PCMCIA_DEVICE_MANF_CARD(0x0137, 0x001b), |
| PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0025), |
| PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0045), |
| PCMCIA_DEVICE_MANF_CARD(0x0137, 0x0052), |
| PCMCIA_DEVICE_PROD_ID134("ADV", "TECH", "COMpad-32/85", 0x67459937, 0x916d02ba, 0x8fbe92ae), |
| PCMCIA_DEVICE_PROD_ID124("GATEWAY2000", "CC3144", "PCMCIA MODEM", 0x506bccae, 0xcb3685f1, 0xbd6c43ef), |
| PCMCIA_DEVICE_PROD_ID14("MEGAHERTZ", "PCMCIA MODEM", 0xf510db04, 0xbd6c43ef), |
| PCMCIA_DEVICE_PROD_ID124("TOSHIBA", "T144PF", "PCMCIA MODEM", 0xb4585a1a, 0x7271409c, 0xbd6c43ef), |
| PCMCIA_DEVICE_PROD_ID123("FUJITSU", "FC14F ", "MBH10213", 0x6ee5a3d8, 0x30ead12b, 0xb00f05a0), |
| PCMCIA_DEVICE_PROD_ID123("Novatel Wireless", "Merlin UMTS Modem", "U630", 0x32607776, 0xd9e73b13, 0xe87332e), |
| PCMCIA_DEVICE_PROD_ID13("MEGAHERTZ", "V.34 PCMCIA MODEM", 0xf510db04, 0xbb2cce4a), |
| PCMCIA_DEVICE_PROD_ID12("Brain Boxes", "Bluetooth PC Card", 0xee138382, 0xd4ce9b02), |
| PCMCIA_DEVICE_PROD_ID12("CIRRUS LOGIC", "FAX MODEM", 0xe625f451, 0xcecd6dfa), |
| PCMCIA_DEVICE_PROD_ID12("COMPAQ", "PCMCIA 28800 FAX/DATA MODEM", 0xa3a3062c, 0x8cbd7c76), |
| PCMCIA_DEVICE_PROD_ID12("COMPAQ", "PCMCIA 33600 FAX/DATA MODEM", 0xa3a3062c, 0x5a00ce95), |
| PCMCIA_DEVICE_PROD_ID12("Computerboards, Inc.", "PCM-COM422", 0xd0b78f51, 0x7e2d49ed), |
| PCMCIA_DEVICE_PROD_ID12("Dr. Neuhaus", "FURY CARD 14K4", 0x76942813, 0x8b96ce65), |
| PCMCIA_DEVICE_PROD_ID12("Intelligent", "ANGIA FAX/MODEM", 0xb496e65e, 0xf31602a6), |
| PCMCIA_DEVICE_PROD_ID12("Intel", "MODEM 2400+", 0x816cc815, 0x412729fb), |
| PCMCIA_DEVICE_PROD_ID12("IOTech Inc ", "PCMCIA Dual RS-232 Serial Port Card", 0x3bd2d898, 0x92abc92f), |
| PCMCIA_DEVICE_PROD_ID12("MACRONIX", "FAX/MODEM", 0x668388b3, 0x3f9bdf2f), |
| PCMCIA_DEVICE_PROD_ID12("Multi-Tech", "MT1432LT", 0x5f73be51, 0x0b3e2383), |
| PCMCIA_DEVICE_PROD_ID12("Multi-Tech", "MT2834LT", 0x5f73be51, 0x4cd7c09e), |
| PCMCIA_DEVICE_PROD_ID12("OEM ", "C288MX ", 0xb572d360, 0xd2385b7a), |
| PCMCIA_DEVICE_PROD_ID12("PCMCIA ", "C336MX ", 0x99bcafe9, 0xaa25bcab), |
| PCMCIA_DEVICE_PROD_ID12("Quatech Inc", "PCMCIA Dual RS-232 Serial Port Card", 0xc4420b35, 0x92abc92f), |
| PCMCIA_DEVICE_PROD_ID12("Quatech Inc", "Dual RS-232 Serial Port PC Card", 0xc4420b35, 0x031a380d), |
| PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "PCMCIA", "EN2218-LAN/MODEM", 0x281f1c5d, 0x570f348e, "cis/PCMLM28.cis"), |
| PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "PCMCIA", "UE2218-LAN/MODEM", 0x281f1c5d, 0x6fdcacee, "cis/PCMLM28.cis"), |
| PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "Psion Dacom", "Gold Card V34 Ethernet", 0xf5f025c2, 0x338e8155, "cis/PCMLM28.cis"), |
| PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "Psion Dacom", "Gold Card V34 Ethernet GSM", 0xf5f025c2, 0x4ae85d35, "cis/PCMLM28.cis"), |
| PCMCIA_PFC_DEVICE_CIS_PROD_ID12(1, "LINKSYS", "PCMLM28", 0xf7cb0b07, 0x66881874, "cis/PCMLM28.cis"), |
| PCMCIA_MFC_DEVICE_CIS_PROD_ID12(1, "DAYNA COMMUNICATIONS", "LAN AND MODEM MULTIFUNCTION", 0x8fdf8f89, 0xdd5ed9e8, "cis/DP83903.cis"), |
| PCMCIA_MFC_DEVICE_CIS_PROD_ID4(1, "NSC MF LAN/Modem", 0x58fc6056, "cis/DP83903.cis"), |
| PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x0556, "cis/3CCFEM556.cis"), |
| PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0175, 0x0000, "cis/DP83903.cis"), |
| PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x0035, "cis/3CXEM556.cis"), |
| PCMCIA_MFC_DEVICE_CIS_MANF_CARD(1, 0x0101, 0x003d, "cis/3CXEM556.cis"), |
| PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC850", 0xd85f6206, 0x42a2c018, "cis/SW_8xx_SER.cis"), /* Sierra Wireless AC850 3G Network Adapter R1 */ |
| PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC860", 0xd85f6206, 0x698f93db, "cis/SW_8xx_SER.cis"), /* Sierra Wireless AC860 3G Network Adapter R1 */ |
| PCMCIA_DEVICE_CIS_PROD_ID12("Sierra Wireless", "AC710/AC750", 0xd85f6206, 0x761b11e0, "cis/SW_7xx_SER.cis"), /* Sierra Wireless AC710/AC750 GPRS Network Adapter R1 */ |
| PCMCIA_DEVICE_CIS_MANF_CARD(0x0192, 0xa555, "cis/SW_555_SER.cis"), /* Sierra Aircard 555 CDMA 1xrtt Modem -- pre update */ |
| PCMCIA_DEVICE_CIS_MANF_CARD(0x013f, 0xa555, "cis/SW_555_SER.cis"), /* Sierra Aircard 555 CDMA 1xrtt Modem -- post update */ |
| PCMCIA_DEVICE_CIS_PROD_ID12("MultiTech", "PCMCIA 56K DataFax", 0x842047ee, 0xc2efcf03, "cis/MT5634ZLX.cis"), |
| PCMCIA_DEVICE_CIS_PROD_ID12("ADVANTECH", "COMpad-32/85B-2", 0x96913a85, 0x27ab5437, "cis/COMpad2.cis"), |
| PCMCIA_DEVICE_CIS_PROD_ID12("ADVANTECH", "COMpad-32/85B-4", 0x96913a85, 0xcec8f102, "cis/COMpad4.cis"), |
| PCMCIA_DEVICE_CIS_PROD_ID123("ADVANTECH", "COMpad-32/85", "1.0", 0x96913a85, 0x8fbe92ae, 0x0877b627, "cis/COMpad2.cis"), |
| PCMCIA_DEVICE_CIS_PROD_ID2("RS-COM 2P", 0xad20b156, "cis/RS-COM-2P.cis"), |
| PCMCIA_DEVICE_CIS_MANF_CARD(0x0013, 0x0000, "cis/GLOBETROTTER.cis"), |
| PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.","SERIAL CARD: SL100 1.00.",0x19ca78af,0xf964f42b), |
| PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.","SERIAL CARD: SL100",0x19ca78af,0x71d98e83), |
| PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.","SERIAL CARD: SL232 1.00.",0x19ca78af,0x69fb7490), |
| PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c1997.","SERIAL CARD: SL232",0x19ca78af,0xb6bc0235), |
| PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c2000.","SERIAL CARD: CF232",0x63f2e0bd,0xb9e175d3), |
| PCMCIA_DEVICE_PROD_ID12("ELAN DIGITAL SYSTEMS LTD, c2000.","SERIAL CARD: CF232-5",0x63f2e0bd,0xfce33442), |
| PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: CF232",0x3beb8cf2,0x171e7190), |
| PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: CF232-5",0x3beb8cf2,0x20da4262), |
| PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: CF428",0x3beb8cf2,0xea5dd57d), |
| PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: CF500",0x3beb8cf2,0xd77255fa), |
| PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: IC232",0x3beb8cf2,0x6a709903), |
| PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: SL232",0x3beb8cf2,0x18430676), |
| PCMCIA_DEVICE_PROD_ID12("Elan","Serial Port: XL232",0x3beb8cf2,0x6f933767), |
| PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial Port: CF332",0x3beb8cf2,0x16dc1ba7), |
| PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial Port: SL332",0x3beb8cf2,0x19816c41), |
| PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial Port: SL385",0x3beb8cf2,0x64112029), |
| PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial Port: SL432",0x3beb8cf2,0x1cce7ac4), |
| PCMCIA_MFC_DEVICE_PROD_ID12(0,"Elan","Serial+Parallel Port: SP230",0x3beb8cf2,0xdb9e58bc), |
| PCMCIA_MFC_DEVICE_PROD_ID12(1,"Elan","Serial Port: CF332",0x3beb8cf2,0x16dc1ba7), |
| PCMCIA_MFC_DEVICE_PROD_ID12(1,"Elan","Serial Port: SL332",0x3beb8cf2,0x19816c41), |
| PCMCIA_MFC_DEVICE_PROD_ID12(1,"Elan","Serial Port: SL385",0x3beb8cf2,0x64112029), |
| PCMCIA_MFC_DEVICE_PROD_ID12(1,"Elan","Serial Port: SL432",0x3beb8cf2,0x1cce7ac4), |
| PCMCIA_MFC_DEVICE_PROD_ID12(2,"Elan","Serial Port: SL432",0x3beb8cf2,0x1cce7ac4), |
| PCMCIA_MFC_DEVICE_PROD_ID12(3,"Elan","Serial Port: SL432",0x3beb8cf2,0x1cce7ac4), |
| PCMCIA_DEVICE_MANF_CARD(0x0279, 0x950b), |
| /* too generic */ |
| /* PCMCIA_MFC_DEVICE_MANF_CARD(0, 0x0160, 0x0002), */ |
| /* PCMCIA_MFC_DEVICE_MANF_CARD(1, 0x0160, 0x0002), */ |
| PCMCIA_DEVICE_FUNC_ID(2), |
| PCMCIA_DEVICE_NULL, |
| }; |
| MODULE_DEVICE_TABLE(pcmcia, serial_ids); |
| |
| MODULE_FIRMWARE("cis/PCMLM28.cis"); |
| MODULE_FIRMWARE("cis/DP83903.cis"); |
| MODULE_FIRMWARE("cis/3CCFEM556.cis"); |
| MODULE_FIRMWARE("cis/3CXEM556.cis"); |
| MODULE_FIRMWARE("cis/SW_8xx_SER.cis"); |
| MODULE_FIRMWARE("cis/SW_7xx_SER.cis"); |
| MODULE_FIRMWARE("cis/SW_555_SER.cis"); |
| MODULE_FIRMWARE("cis/MT5634ZLX.cis"); |
| MODULE_FIRMWARE("cis/COMpad2.cis"); |
| MODULE_FIRMWARE("cis/COMpad4.cis"); |
| MODULE_FIRMWARE("cis/RS-COM-2P.cis"); |
| |
| static struct pcmcia_driver serial_cs_driver = { |
| .owner = THIS_MODULE, |
| .drv = { |
| .name = "serial_cs", |
| }, |
| .probe = serial_probe, |
| .remove = serial_detach, |
| .id_table = serial_ids, |
| .suspend = serial_suspend, |
| .resume = serial_resume, |
| }; |
| |
| static int __init init_serial_cs(void) |
| { |
| return pcmcia_register_driver(&serial_cs_driver); |
| } |
| |
| static void __exit exit_serial_cs(void) |
| { |
| pcmcia_unregister_driver(&serial_cs_driver); |
| } |
| |
| module_init(init_serial_cs); |
| module_exit(exit_serial_cs); |
| |
| MODULE_LICENSE("GPL"); |