mac80211: call rate control only after init
There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/net/mac80211/debugfs_sta.c b/net/mac80211/debugfs_sta.c
index 2406b3e..d86217d 100644
--- a/net/mac80211/debugfs_sta.c
+++ b/net/mac80211/debugfs_sta.c
@@ -63,14 +63,14 @@
test_sta_flag(sta, WLAN_STA_##flg) ? #flg "\n" : ""
int res = scnprintf(buf, sizeof(buf),
- "%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s",
+ "%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s",
TEST(AUTH), TEST(ASSOC), TEST(PS_STA),
TEST(PS_DRIVER), TEST(AUTHORIZED),
TEST(SHORT_PREAMBLE),
TEST(WME), TEST(WDS), TEST(CLEAR_PS_FILT),
TEST(MFP), TEST(BLOCK_BA), TEST(PSPOLL),
TEST(UAPSD), TEST(SP), TEST(TDLS_PEER),
- TEST(TDLS_PEER_AUTH));
+ TEST(TDLS_PEER_AUTH), TEST(RATE_CONTROL));
#undef TEST
return simple_read_from_buffer(userbuf, count, ppos, buf, res);
}
diff --git a/net/mac80211/rate.c b/net/mac80211/rate.c
index 5a5a776..ad64f4d 100644
--- a/net/mac80211/rate.c
+++ b/net/mac80211/rate.c
@@ -336,7 +336,7 @@
int i;
u32 mask;
- if (sta) {
+ if (sta && test_sta_flag(sta, WLAN_STA_RATE_CONTROL)) {
ista = &sta->sta;
priv_sta = sta->rate_ctrl_priv;
}
diff --git a/net/mac80211/rate.h b/net/mac80211/rate.h
index 168427b..2b83f32 100644
--- a/net/mac80211/rate.h
+++ b/net/mac80211/rate.h
@@ -62,6 +62,7 @@
sband = local->hw.wiphy->bands[local->hw.conf.channel->band];
ref->ops->rate_init(ref->priv, sband, ista, priv_sta);
+ set_sta_flag(sta, WLAN_STA_RATE_CONTROL);
}
static inline void rate_control_rate_update(struct ieee80211_local *local,
diff --git a/net/mac80211/sta_info.h b/net/mac80211/sta_info.h
index 6f77f12..bfed851 100644
--- a/net/mac80211/sta_info.h
+++ b/net/mac80211/sta_info.h
@@ -52,6 +52,7 @@
* @WLAN_STA_SP: Station is in a service period, so don't try to
* reply to other uAPSD trigger frames or PS-Poll.
* @WLAN_STA_4ADDR_EVENT: 4-addr event was already sent for this frame.
+ * @WLAN_STA_RATE_CONTROL: rate control was initialized for this station.
*/
enum ieee80211_sta_info_flags {
WLAN_STA_AUTH,
@@ -71,6 +72,7 @@
WLAN_STA_UAPSD,
WLAN_STA_SP,
WLAN_STA_4ADDR_EVENT,
+ WLAN_STA_RATE_CONTROL,
};
enum ieee80211_sta_state {