| /* |
| * sata_sil24.c - Driver for Silicon Image 3124/3132 SATA-2 controllers |
| * |
| * Copyright 2005 Tejun Heo |
| * |
| * Based on preview driver from Silicon Image. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2, or (at your option) any |
| * later version. |
| * |
| * This program is distributed in the hope that it will be useful, but |
| * WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU |
| * General Public License for more details. |
| * |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/pci.h> |
| #include <linux/blkdev.h> |
| #include <linux/delay.h> |
| #include <linux/interrupt.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/device.h> |
| #include <scsi/scsi_host.h> |
| #include <scsi/scsi_cmnd.h> |
| #include <linux/libata.h> |
| #include <asm/io.h> |
| |
| #define DRV_NAME "sata_sil24" |
| #define DRV_VERSION "0.3" |
| |
| /* |
| * Port request block (PRB) 32 bytes |
| */ |
| struct sil24_prb { |
| __le16 ctrl; |
| __le16 prot; |
| __le32 rx_cnt; |
| u8 fis[6 * 4]; |
| }; |
| |
| /* |
| * Scatter gather entry (SGE) 16 bytes |
| */ |
| struct sil24_sge { |
| __le64 addr; |
| __le32 cnt; |
| __le32 flags; |
| }; |
| |
| /* |
| * Port multiplier |
| */ |
| struct sil24_port_multiplier { |
| __le32 diag; |
| __le32 sactive; |
| }; |
| |
| enum { |
| /* |
| * Global controller registers (128 bytes @ BAR0) |
| */ |
| /* 32 bit regs */ |
| HOST_SLOT_STAT = 0x00, /* 32 bit slot stat * 4 */ |
| HOST_CTRL = 0x40, |
| HOST_IRQ_STAT = 0x44, |
| HOST_PHY_CFG = 0x48, |
| HOST_BIST_CTRL = 0x50, |
| HOST_BIST_PTRN = 0x54, |
| HOST_BIST_STAT = 0x58, |
| HOST_MEM_BIST_STAT = 0x5c, |
| HOST_FLASH_CMD = 0x70, |
| /* 8 bit regs */ |
| HOST_FLASH_DATA = 0x74, |
| HOST_TRANSITION_DETECT = 0x75, |
| HOST_GPIO_CTRL = 0x76, |
| HOST_I2C_ADDR = 0x78, /* 32 bit */ |
| HOST_I2C_DATA = 0x7c, |
| HOST_I2C_XFER_CNT = 0x7e, |
| HOST_I2C_CTRL = 0x7f, |
| |
| /* HOST_SLOT_STAT bits */ |
| HOST_SSTAT_ATTN = (1 << 31), |
| |
| /* HOST_CTRL bits */ |
| HOST_CTRL_M66EN = (1 << 16), /* M66EN PCI bus signal */ |
| HOST_CTRL_TRDY = (1 << 17), /* latched PCI TRDY */ |
| HOST_CTRL_STOP = (1 << 18), /* latched PCI STOP */ |
| HOST_CTRL_DEVSEL = (1 << 19), /* latched PCI DEVSEL */ |
| HOST_CTRL_REQ64 = (1 << 20), /* latched PCI REQ64 */ |
| HOST_CTRL_GLOBAL_RST = (1 << 31), /* global reset */ |
| |
| /* |
| * Port registers |
| * (8192 bytes @ +0x0000, +0x2000, +0x4000 and +0x6000 @ BAR2) |
| */ |
| PORT_REGS_SIZE = 0x2000, |
| |
| PORT_LRAM = 0x0000, /* 31 LRAM slots and PM regs */ |
| PORT_LRAM_SLOT_SZ = 0x0080, /* 32 bytes PRB + 2 SGE, ACT... */ |
| |
| PORT_PM = 0x0f80, /* 8 bytes PM * 16 (128 bytes) */ |
| /* 32 bit regs */ |
| PORT_CTRL_STAT = 0x1000, /* write: ctrl-set, read: stat */ |
| PORT_CTRL_CLR = 0x1004, /* write: ctrl-clear */ |
| PORT_IRQ_STAT = 0x1008, /* high: status, low: interrupt */ |
| PORT_IRQ_ENABLE_SET = 0x1010, /* write: enable-set */ |
| PORT_IRQ_ENABLE_CLR = 0x1014, /* write: enable-clear */ |
| PORT_ACTIVATE_UPPER_ADDR= 0x101c, |
| PORT_EXEC_FIFO = 0x1020, /* command execution fifo */ |
| PORT_CMD_ERR = 0x1024, /* command error number */ |
| PORT_FIS_CFG = 0x1028, |
| PORT_FIFO_THRES = 0x102c, |
| /* 16 bit regs */ |
| PORT_DECODE_ERR_CNT = 0x1040, |
| PORT_DECODE_ERR_THRESH = 0x1042, |
| PORT_CRC_ERR_CNT = 0x1044, |
| PORT_CRC_ERR_THRESH = 0x1046, |
| PORT_HSHK_ERR_CNT = 0x1048, |
| PORT_HSHK_ERR_THRESH = 0x104a, |
| /* 32 bit regs */ |
| PORT_PHY_CFG = 0x1050, |
| PORT_SLOT_STAT = 0x1800, |
| PORT_CMD_ACTIVATE = 0x1c00, /* 64 bit cmd activate * 31 (248 bytes) */ |
| PORT_EXEC_DIAG = 0x1e00, /* 32bit exec diag * 16 (64 bytes, 0-10 used on 3124) */ |
| PORT_PSD_DIAG = 0x1e40, /* 32bit psd diag * 16 (64 bytes, 0-8 used on 3124) */ |
| PORT_SCONTROL = 0x1f00, |
| PORT_SSTATUS = 0x1f04, |
| PORT_SERROR = 0x1f08, |
| PORT_SACTIVE = 0x1f0c, |
| |
| /* PORT_CTRL_STAT bits */ |
| PORT_CS_PORT_RST = (1 << 0), /* port reset */ |
| PORT_CS_DEV_RST = (1 << 1), /* device reset */ |
| PORT_CS_INIT = (1 << 2), /* port initialize */ |
| PORT_CS_IRQ_WOC = (1 << 3), /* interrupt write one to clear */ |
| PORT_CS_CDB16 = (1 << 5), /* 0=12b cdb, 1=16b cdb */ |
| PORT_CS_RESUME = (1 << 6), /* port resume */ |
| PORT_CS_32BIT_ACTV = (1 << 10), /* 32-bit activation */ |
| PORT_CS_PM_EN = (1 << 13), /* port multiplier enable */ |
| PORT_CS_RDY = (1 << 31), /* port ready to accept commands */ |
| |
| /* PORT_IRQ_STAT/ENABLE_SET/CLR */ |
| /* bits[11:0] are masked */ |
| PORT_IRQ_COMPLETE = (1 << 0), /* command(s) completed */ |
| PORT_IRQ_ERROR = (1 << 1), /* command execution error */ |
| PORT_IRQ_PORTRDY_CHG = (1 << 2), /* port ready change */ |
| PORT_IRQ_PWR_CHG = (1 << 3), /* power management change */ |
| PORT_IRQ_PHYRDY_CHG = (1 << 4), /* PHY ready change */ |
| PORT_IRQ_COMWAKE = (1 << 5), /* COMWAKE received */ |
| PORT_IRQ_UNK_FIS = (1 << 6), /* unknown FIS received */ |
| PORT_IRQ_DEV_XCHG = (1 << 7), /* device exchanged */ |
| PORT_IRQ_8B10B = (1 << 8), /* 8b/10b decode error threshold */ |
| PORT_IRQ_CRC = (1 << 9), /* CRC error threshold */ |
| PORT_IRQ_HANDSHAKE = (1 << 10), /* handshake error threshold */ |
| PORT_IRQ_SDB_NOTIFY = (1 << 11), /* SDB notify received */ |
| |
| DEF_PORT_IRQ = PORT_IRQ_COMPLETE | PORT_IRQ_ERROR | |
| PORT_IRQ_PHYRDY_CHG | PORT_IRQ_DEV_XCHG | |
| PORT_IRQ_UNK_FIS, |
| |
| /* bits[27:16] are unmasked (raw) */ |
| PORT_IRQ_RAW_SHIFT = 16, |
| PORT_IRQ_MASKED_MASK = 0x7ff, |
| PORT_IRQ_RAW_MASK = (0x7ff << PORT_IRQ_RAW_SHIFT), |
| |
| /* ENABLE_SET/CLR specific, intr steering - 2 bit field */ |
| PORT_IRQ_STEER_SHIFT = 30, |
| PORT_IRQ_STEER_MASK = (3 << PORT_IRQ_STEER_SHIFT), |
| |
| /* PORT_CMD_ERR constants */ |
| PORT_CERR_DEV = 1, /* Error bit in D2H Register FIS */ |
| PORT_CERR_SDB = 2, /* Error bit in SDB FIS */ |
| PORT_CERR_DATA = 3, /* Error in data FIS not detected by dev */ |
| PORT_CERR_SEND = 4, /* Initial cmd FIS transmission failure */ |
| PORT_CERR_INCONSISTENT = 5, /* Protocol mismatch */ |
| PORT_CERR_DIRECTION = 6, /* Data direction mismatch */ |
| PORT_CERR_UNDERRUN = 7, /* Ran out of SGEs while writing */ |
| PORT_CERR_OVERRUN = 8, /* Ran out of SGEs while reading */ |
| PORT_CERR_PKT_PROT = 11, /* DIR invalid in 1st PIO setup of ATAPI */ |
| PORT_CERR_SGT_BOUNDARY = 16, /* PLD ecode 00 - SGT not on qword boundary */ |
| PORT_CERR_SGT_TGTABRT = 17, /* PLD ecode 01 - target abort */ |
| PORT_CERR_SGT_MSTABRT = 18, /* PLD ecode 10 - master abort */ |
| PORT_CERR_SGT_PCIPERR = 19, /* PLD ecode 11 - PCI parity err while fetching SGT */ |
| PORT_CERR_CMD_BOUNDARY = 24, /* ctrl[15:13] 001 - PRB not on qword boundary */ |
| PORT_CERR_CMD_TGTABRT = 25, /* ctrl[15:13] 010 - target abort */ |
| PORT_CERR_CMD_MSTABRT = 26, /* ctrl[15:13] 100 - master abort */ |
| PORT_CERR_CMD_PCIPERR = 27, /* ctrl[15:13] 110 - PCI parity err while fetching PRB */ |
| PORT_CERR_XFR_UNDEF = 32, /* PSD ecode 00 - undefined */ |
| PORT_CERR_XFR_TGTABRT = 33, /* PSD ecode 01 - target abort */ |
| PORT_CERR_XFR_MSTABRT = 34, /* PSD ecode 10 - master abort */ |
| PORT_CERR_XFR_PCIPERR = 35, /* PSD ecode 11 - PCI prity err during transfer */ |
| PORT_CERR_SENDSERVICE = 36, /* FIS received while sending service */ |
| |
| /* bits of PRB control field */ |
| PRB_CTRL_PROTOCOL = (1 << 0), /* override def. ATA protocol */ |
| PRB_CTRL_PACKET_READ = (1 << 4), /* PACKET cmd read */ |
| PRB_CTRL_PACKET_WRITE = (1 << 5), /* PACKET cmd write */ |
| PRB_CTRL_NIEN = (1 << 6), /* Mask completion irq */ |
| PRB_CTRL_SRST = (1 << 7), /* Soft reset request (ign BSY?) */ |
| |
| /* PRB protocol field */ |
| PRB_PROT_PACKET = (1 << 0), |
| PRB_PROT_TCQ = (1 << 1), |
| PRB_PROT_NCQ = (1 << 2), |
| PRB_PROT_READ = (1 << 3), |
| PRB_PROT_WRITE = (1 << 4), |
| PRB_PROT_TRANSPARENT = (1 << 5), |
| |
| /* |
| * Other constants |
| */ |
| SGE_TRM = (1 << 31), /* Last SGE in chain */ |
| SGE_LNK = (1 << 30), /* linked list |
| Points to SGT, not SGE */ |
| SGE_DRD = (1 << 29), /* discard data read (/dev/null) |
| data address ignored */ |
| |
| SIL24_MAX_CMDS = 31, |
| |
| /* board id */ |
| BID_SIL3124 = 0, |
| BID_SIL3132 = 1, |
| BID_SIL3131 = 2, |
| |
| /* host flags */ |
| SIL24_COMMON_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | |
| ATA_FLAG_MMIO | ATA_FLAG_PIO_DMA | |
| ATA_FLAG_NCQ | ATA_FLAG_SKIP_D2H_BSY, |
| SIL24_FLAG_PCIX_IRQ_WOC = (1 << 24), /* IRQ loss errata on PCI-X */ |
| |
| IRQ_STAT_4PORTS = 0xf, |
| }; |
| |
| struct sil24_ata_block { |
| struct sil24_prb prb; |
| struct sil24_sge sge[LIBATA_MAX_PRD]; |
| }; |
| |
| struct sil24_atapi_block { |
| struct sil24_prb prb; |
| u8 cdb[16]; |
| struct sil24_sge sge[LIBATA_MAX_PRD - 1]; |
| }; |
| |
| union sil24_cmd_block { |
| struct sil24_ata_block ata; |
| struct sil24_atapi_block atapi; |
| }; |
| |
| static struct sil24_cerr_info { |
| unsigned int err_mask, action; |
| const char *desc; |
| } sil24_cerr_db[] = { |
| [0] = { AC_ERR_DEV, ATA_EH_REVALIDATE, |
| "device error" }, |
| [PORT_CERR_DEV] = { AC_ERR_DEV, ATA_EH_REVALIDATE, |
| "device error via D2H FIS" }, |
| [PORT_CERR_SDB] = { AC_ERR_DEV, ATA_EH_REVALIDATE, |
| "device error via SDB FIS" }, |
| [PORT_CERR_DATA] = { AC_ERR_ATA_BUS, ATA_EH_SOFTRESET, |
| "error in data FIS" }, |
| [PORT_CERR_SEND] = { AC_ERR_ATA_BUS, ATA_EH_SOFTRESET, |
| "failed to transmit command FIS" }, |
| [PORT_CERR_INCONSISTENT] = { AC_ERR_HSM, ATA_EH_SOFTRESET, |
| "protocol mismatch" }, |
| [PORT_CERR_DIRECTION] = { AC_ERR_HSM, ATA_EH_SOFTRESET, |
| "data directon mismatch" }, |
| [PORT_CERR_UNDERRUN] = { AC_ERR_HSM, ATA_EH_SOFTRESET, |
| "ran out of SGEs while writing" }, |
| [PORT_CERR_OVERRUN] = { AC_ERR_HSM, ATA_EH_SOFTRESET, |
| "ran out of SGEs while reading" }, |
| [PORT_CERR_PKT_PROT] = { AC_ERR_HSM, ATA_EH_SOFTRESET, |
| "invalid data directon for ATAPI CDB" }, |
| [PORT_CERR_SGT_BOUNDARY] = { AC_ERR_SYSTEM, ATA_EH_SOFTRESET, |
| "SGT no on qword boundary" }, |
| [PORT_CERR_SGT_TGTABRT] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, |
| "PCI target abort while fetching SGT" }, |
| [PORT_CERR_SGT_MSTABRT] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, |
| "PCI master abort while fetching SGT" }, |
| [PORT_CERR_SGT_PCIPERR] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, |
| "PCI parity error while fetching SGT" }, |
| [PORT_CERR_CMD_BOUNDARY] = { AC_ERR_SYSTEM, ATA_EH_SOFTRESET, |
| "PRB not on qword boundary" }, |
| [PORT_CERR_CMD_TGTABRT] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, |
| "PCI target abort while fetching PRB" }, |
| [PORT_CERR_CMD_MSTABRT] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, |
| "PCI master abort while fetching PRB" }, |
| [PORT_CERR_CMD_PCIPERR] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, |
| "PCI parity error while fetching PRB" }, |
| [PORT_CERR_XFR_UNDEF] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, |
| "undefined error while transferring data" }, |
| [PORT_CERR_XFR_TGTABRT] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, |
| "PCI target abort while transferring data" }, |
| [PORT_CERR_XFR_MSTABRT] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, |
| "PCI master abort while transferring data" }, |
| [PORT_CERR_XFR_PCIPERR] = { AC_ERR_HOST_BUS, ATA_EH_SOFTRESET, |
| "PCI parity error while transferring data" }, |
| [PORT_CERR_SENDSERVICE] = { AC_ERR_HSM, ATA_EH_SOFTRESET, |
| "FIS received while sending service FIS" }, |
| }; |
| |
| /* |
| * ap->private_data |
| * |
| * The preview driver always returned 0 for status. We emulate it |
| * here from the previous interrupt. |
| */ |
| struct sil24_port_priv { |
| union sil24_cmd_block *cmd_block; /* 32 cmd blocks */ |
| dma_addr_t cmd_block_dma; /* DMA base addr for them */ |
| struct ata_taskfile tf; /* Cached taskfile registers */ |
| }; |
| |
| /* ap->host->private_data */ |
| struct sil24_host_priv { |
| void __iomem *host_base; /* global controller control (128 bytes @BAR0) */ |
| void __iomem *port_base; /* port registers (4 * 8192 bytes @BAR2) */ |
| }; |
| |
| static void sil24_dev_config(struct ata_port *ap, struct ata_device *dev); |
| static u8 sil24_check_status(struct ata_port *ap); |
| static u32 sil24_scr_read(struct ata_port *ap, unsigned sc_reg); |
| static void sil24_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val); |
| static void sil24_tf_read(struct ata_port *ap, struct ata_taskfile *tf); |
| static void sil24_qc_prep(struct ata_queued_cmd *qc); |
| static unsigned int sil24_qc_issue(struct ata_queued_cmd *qc); |
| static void sil24_irq_clear(struct ata_port *ap); |
| static irqreturn_t sil24_interrupt(int irq, void *dev_instance, struct pt_regs *regs); |
| static void sil24_freeze(struct ata_port *ap); |
| static void sil24_thaw(struct ata_port *ap); |
| static void sil24_error_handler(struct ata_port *ap); |
| static void sil24_post_internal_cmd(struct ata_queued_cmd *qc); |
| static int sil24_port_start(struct ata_port *ap); |
| static void sil24_port_stop(struct ata_port *ap); |
| static void sil24_host_stop(struct ata_host *host); |
| static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent); |
| #ifdef CONFIG_PM |
| static int sil24_pci_device_resume(struct pci_dev *pdev); |
| #endif |
| |
| static const struct pci_device_id sil24_pci_tbl[] = { |
| { PCI_VDEVICE(CMD, 0x3124), BID_SIL3124 }, |
| { PCI_VDEVICE(INTEL, 0x3124), BID_SIL3124 }, |
| { PCI_VDEVICE(CMD, 0x3132), BID_SIL3132 }, |
| { PCI_VDEVICE(CMD, 0x3131), BID_SIL3131 }, |
| { PCI_VDEVICE(CMD, 0x3531), BID_SIL3131 }, |
| |
| { } /* terminate list */ |
| }; |
| |
| static struct pci_driver sil24_pci_driver = { |
| .name = DRV_NAME, |
| .id_table = sil24_pci_tbl, |
| .probe = sil24_init_one, |
| .remove = ata_pci_remove_one, /* safe? */ |
| #ifdef CONFIG_PM |
| .suspend = ata_pci_device_suspend, |
| .resume = sil24_pci_device_resume, |
| #endif |
| }; |
| |
| static struct scsi_host_template sil24_sht = { |
| .module = THIS_MODULE, |
| .name = DRV_NAME, |
| .ioctl = ata_scsi_ioctl, |
| .queuecommand = ata_scsi_queuecmd, |
| .change_queue_depth = ata_scsi_change_queue_depth, |
| .can_queue = SIL24_MAX_CMDS, |
| .this_id = ATA_SHT_THIS_ID, |
| .sg_tablesize = LIBATA_MAX_PRD, |
| .cmd_per_lun = ATA_SHT_CMD_PER_LUN, |
| .emulated = ATA_SHT_EMULATED, |
| .use_clustering = ATA_SHT_USE_CLUSTERING, |
| .proc_name = DRV_NAME, |
| .dma_boundary = ATA_DMA_BOUNDARY, |
| .slave_configure = ata_scsi_slave_config, |
| .slave_destroy = ata_scsi_slave_destroy, |
| .bios_param = ata_std_bios_param, |
| .suspend = ata_scsi_device_suspend, |
| .resume = ata_scsi_device_resume, |
| }; |
| |
| static const struct ata_port_operations sil24_ops = { |
| .port_disable = ata_port_disable, |
| |
| .dev_config = sil24_dev_config, |
| |
| .check_status = sil24_check_status, |
| .check_altstatus = sil24_check_status, |
| .dev_select = ata_noop_dev_select, |
| |
| .tf_read = sil24_tf_read, |
| |
| .qc_prep = sil24_qc_prep, |
| .qc_issue = sil24_qc_issue, |
| |
| .irq_handler = sil24_interrupt, |
| .irq_clear = sil24_irq_clear, |
| |
| .scr_read = sil24_scr_read, |
| .scr_write = sil24_scr_write, |
| |
| .freeze = sil24_freeze, |
| .thaw = sil24_thaw, |
| .error_handler = sil24_error_handler, |
| .post_internal_cmd = sil24_post_internal_cmd, |
| |
| .port_start = sil24_port_start, |
| .port_stop = sil24_port_stop, |
| .host_stop = sil24_host_stop, |
| }; |
| |
| /* |
| * Use bits 30-31 of port_flags to encode available port numbers. |
| * Current maxium is 4. |
| */ |
| #define SIL24_NPORTS2FLAG(nports) ((((unsigned)(nports) - 1) & 0x3) << 30) |
| #define SIL24_FLAG2NPORTS(flag) ((((flag) >> 30) & 0x3) + 1) |
| |
| static struct ata_port_info sil24_port_info[] = { |
| /* sil_3124 */ |
| { |
| .sht = &sil24_sht, |
| .flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(4) | |
| SIL24_FLAG_PCIX_IRQ_WOC, |
| .pio_mask = 0x1f, /* pio0-4 */ |
| .mwdma_mask = 0x07, /* mwdma0-2 */ |
| .udma_mask = 0x3f, /* udma0-5 */ |
| .port_ops = &sil24_ops, |
| }, |
| /* sil_3132 */ |
| { |
| .sht = &sil24_sht, |
| .flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(2), |
| .pio_mask = 0x1f, /* pio0-4 */ |
| .mwdma_mask = 0x07, /* mwdma0-2 */ |
| .udma_mask = 0x3f, /* udma0-5 */ |
| .port_ops = &sil24_ops, |
| }, |
| /* sil_3131/sil_3531 */ |
| { |
| .sht = &sil24_sht, |
| .flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(1), |
| .pio_mask = 0x1f, /* pio0-4 */ |
| .mwdma_mask = 0x07, /* mwdma0-2 */ |
| .udma_mask = 0x3f, /* udma0-5 */ |
| .port_ops = &sil24_ops, |
| }, |
| }; |
| |
| static int sil24_tag(int tag) |
| { |
| if (unlikely(ata_tag_internal(tag))) |
| return 0; |
| return tag; |
| } |
| |
| static void sil24_dev_config(struct ata_port *ap, struct ata_device *dev) |
| { |
| void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; |
| |
| if (dev->cdb_len == 16) |
| writel(PORT_CS_CDB16, port + PORT_CTRL_STAT); |
| else |
| writel(PORT_CS_CDB16, port + PORT_CTRL_CLR); |
| } |
| |
| static inline void sil24_update_tf(struct ata_port *ap) |
| { |
| struct sil24_port_priv *pp = ap->private_data; |
| void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; |
| struct sil24_prb __iomem *prb = port; |
| u8 fis[6 * 4]; |
| |
| memcpy_fromio(fis, prb->fis, 6 * 4); |
| ata_tf_from_fis(fis, &pp->tf); |
| } |
| |
| static u8 sil24_check_status(struct ata_port *ap) |
| { |
| struct sil24_port_priv *pp = ap->private_data; |
| return pp->tf.command; |
| } |
| |
| static int sil24_scr_map[] = { |
| [SCR_CONTROL] = 0, |
| [SCR_STATUS] = 1, |
| [SCR_ERROR] = 2, |
| [SCR_ACTIVE] = 3, |
| }; |
| |
| static u32 sil24_scr_read(struct ata_port *ap, unsigned sc_reg) |
| { |
| void __iomem *scr_addr = (void __iomem *)ap->ioaddr.scr_addr; |
| if (sc_reg < ARRAY_SIZE(sil24_scr_map)) { |
| void __iomem *addr; |
| addr = scr_addr + sil24_scr_map[sc_reg] * 4; |
| return readl(scr_addr + sil24_scr_map[sc_reg] * 4); |
| } |
| return 0xffffffffU; |
| } |
| |
| static void sil24_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val) |
| { |
| void __iomem *scr_addr = (void __iomem *)ap->ioaddr.scr_addr; |
| if (sc_reg < ARRAY_SIZE(sil24_scr_map)) { |
| void __iomem *addr; |
| addr = scr_addr + sil24_scr_map[sc_reg] * 4; |
| writel(val, scr_addr + sil24_scr_map[sc_reg] * 4); |
| } |
| } |
| |
| static void sil24_tf_read(struct ata_port *ap, struct ata_taskfile *tf) |
| { |
| struct sil24_port_priv *pp = ap->private_data; |
| *tf = pp->tf; |
| } |
| |
| static int sil24_init_port(struct ata_port *ap) |
| { |
| void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; |
| u32 tmp; |
| |
| writel(PORT_CS_INIT, port + PORT_CTRL_STAT); |
| ata_wait_register(port + PORT_CTRL_STAT, |
| PORT_CS_INIT, PORT_CS_INIT, 10, 100); |
| tmp = ata_wait_register(port + PORT_CTRL_STAT, |
| PORT_CS_RDY, 0, 10, 100); |
| |
| if ((tmp & (PORT_CS_INIT | PORT_CS_RDY)) != PORT_CS_RDY) |
| return -EIO; |
| return 0; |
| } |
| |
| static int sil24_softreset(struct ata_port *ap, unsigned int *class) |
| { |
| void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; |
| struct sil24_port_priv *pp = ap->private_data; |
| struct sil24_prb *prb = &pp->cmd_block[0].ata.prb; |
| dma_addr_t paddr = pp->cmd_block_dma; |
| u32 mask, irq_stat; |
| const char *reason; |
| |
| DPRINTK("ENTER\n"); |
| |
| if (ata_port_offline(ap)) { |
| DPRINTK("PHY reports no device\n"); |
| *class = ATA_DEV_NONE; |
| goto out; |
| } |
| |
| /* put the port into known state */ |
| if (sil24_init_port(ap)) { |
| reason ="port not ready"; |
| goto err; |
| } |
| |
| /* do SRST */ |
| prb->ctrl = cpu_to_le16(PRB_CTRL_SRST); |
| prb->fis[1] = 0; /* no PM yet */ |
| |
| writel((u32)paddr, port + PORT_CMD_ACTIVATE); |
| writel((u64)paddr >> 32, port + PORT_CMD_ACTIVATE + 4); |
| |
| mask = (PORT_IRQ_COMPLETE | PORT_IRQ_ERROR) << PORT_IRQ_RAW_SHIFT; |
| irq_stat = ata_wait_register(port + PORT_IRQ_STAT, mask, 0x0, |
| 100, ATA_TMOUT_BOOT / HZ * 1000); |
| |
| writel(irq_stat, port + PORT_IRQ_STAT); /* clear IRQs */ |
| irq_stat >>= PORT_IRQ_RAW_SHIFT; |
| |
| if (!(irq_stat & PORT_IRQ_COMPLETE)) { |
| if (irq_stat & PORT_IRQ_ERROR) |
| reason = "SRST command error"; |
| else |
| reason = "timeout"; |
| goto err; |
| } |
| |
| sil24_update_tf(ap); |
| *class = ata_dev_classify(&pp->tf); |
| |
| if (*class == ATA_DEV_UNKNOWN) |
| *class = ATA_DEV_NONE; |
| |
| out: |
| DPRINTK("EXIT, class=%u\n", *class); |
| return 0; |
| |
| err: |
| ata_port_printk(ap, KERN_ERR, "softreset failed (%s)\n", reason); |
| return -EIO; |
| } |
| |
| static int sil24_hardreset(struct ata_port *ap, unsigned int *class) |
| { |
| void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; |
| const char *reason; |
| int tout_msec, rc; |
| u32 tmp; |
| |
| /* sil24 does the right thing(tm) without any protection */ |
| sata_set_spd(ap); |
| |
| tout_msec = 100; |
| if (ata_port_online(ap)) |
| tout_msec = 5000; |
| |
| writel(PORT_CS_DEV_RST, port + PORT_CTRL_STAT); |
| tmp = ata_wait_register(port + PORT_CTRL_STAT, |
| PORT_CS_DEV_RST, PORT_CS_DEV_RST, 10, tout_msec); |
| |
| /* SStatus oscillates between zero and valid status after |
| * DEV_RST, debounce it. |
| */ |
| rc = sata_phy_debounce(ap, sata_deb_timing_long); |
| if (rc) { |
| reason = "PHY debouncing failed"; |
| goto err; |
| } |
| |
| if (tmp & PORT_CS_DEV_RST) { |
| if (ata_port_offline(ap)) |
| return 0; |
| reason = "link not ready"; |
| goto err; |
| } |
| |
| /* Sil24 doesn't store signature FIS after hardreset, so we |
| * can't wait for BSY to clear. Some devices take a long time |
| * to get ready and those devices will choke if we don't wait |
| * for BSY clearance here. Tell libata to perform follow-up |
| * softreset. |
| */ |
| return -EAGAIN; |
| |
| err: |
| ata_port_printk(ap, KERN_ERR, "hardreset failed (%s)\n", reason); |
| return -EIO; |
| } |
| |
| static inline void sil24_fill_sg(struct ata_queued_cmd *qc, |
| struct sil24_sge *sge) |
| { |
| struct scatterlist *sg; |
| unsigned int idx = 0; |
| |
| ata_for_each_sg(sg, qc) { |
| sge->addr = cpu_to_le64(sg_dma_address(sg)); |
| sge->cnt = cpu_to_le32(sg_dma_len(sg)); |
| if (ata_sg_is_last(sg, qc)) |
| sge->flags = cpu_to_le32(SGE_TRM); |
| else |
| sge->flags = 0; |
| |
| sge++; |
| idx++; |
| } |
| } |
| |
| static void sil24_qc_prep(struct ata_queued_cmd *qc) |
| { |
| struct ata_port *ap = qc->ap; |
| struct sil24_port_priv *pp = ap->private_data; |
| union sil24_cmd_block *cb; |
| struct sil24_prb *prb; |
| struct sil24_sge *sge; |
| u16 ctrl = 0; |
| |
| cb = &pp->cmd_block[sil24_tag(qc->tag)]; |
| |
| switch (qc->tf.protocol) { |
| case ATA_PROT_PIO: |
| case ATA_PROT_DMA: |
| case ATA_PROT_NCQ: |
| case ATA_PROT_NODATA: |
| prb = &cb->ata.prb; |
| sge = cb->ata.sge; |
| break; |
| |
| case ATA_PROT_ATAPI: |
| case ATA_PROT_ATAPI_DMA: |
| case ATA_PROT_ATAPI_NODATA: |
| prb = &cb->atapi.prb; |
| sge = cb->atapi.sge; |
| memset(cb->atapi.cdb, 0, 32); |
| memcpy(cb->atapi.cdb, qc->cdb, qc->dev->cdb_len); |
| |
| if (qc->tf.protocol != ATA_PROT_ATAPI_NODATA) { |
| if (qc->tf.flags & ATA_TFLAG_WRITE) |
| ctrl = PRB_CTRL_PACKET_WRITE; |
| else |
| ctrl = PRB_CTRL_PACKET_READ; |
| } |
| break; |
| |
| default: |
| prb = NULL; /* shut up, gcc */ |
| sge = NULL; |
| BUG(); |
| } |
| |
| prb->ctrl = cpu_to_le16(ctrl); |
| ata_tf_to_fis(&qc->tf, prb->fis, 0); |
| |
| if (qc->flags & ATA_QCFLAG_DMAMAP) |
| sil24_fill_sg(qc, sge); |
| } |
| |
| static unsigned int sil24_qc_issue(struct ata_queued_cmd *qc) |
| { |
| struct ata_port *ap = qc->ap; |
| struct sil24_port_priv *pp = ap->private_data; |
| void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; |
| unsigned int tag = sil24_tag(qc->tag); |
| dma_addr_t paddr; |
| void __iomem *activate; |
| |
| paddr = pp->cmd_block_dma + tag * sizeof(*pp->cmd_block); |
| activate = port + PORT_CMD_ACTIVATE + tag * 8; |
| |
| writel((u32)paddr, activate); |
| writel((u64)paddr >> 32, activate + 4); |
| |
| return 0; |
| } |
| |
| static void sil24_irq_clear(struct ata_port *ap) |
| { |
| /* unused */ |
| } |
| |
| static void sil24_freeze(struct ata_port *ap) |
| { |
| void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; |
| |
| /* Port-wide IRQ mask in HOST_CTRL doesn't really work, clear |
| * PORT_IRQ_ENABLE instead. |
| */ |
| writel(0xffff, port + PORT_IRQ_ENABLE_CLR); |
| } |
| |
| static void sil24_thaw(struct ata_port *ap) |
| { |
| void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; |
| u32 tmp; |
| |
| /* clear IRQ */ |
| tmp = readl(port + PORT_IRQ_STAT); |
| writel(tmp, port + PORT_IRQ_STAT); |
| |
| /* turn IRQ back on */ |
| writel(DEF_PORT_IRQ, port + PORT_IRQ_ENABLE_SET); |
| } |
| |
| static void sil24_error_intr(struct ata_port *ap) |
| { |
| void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; |
| struct ata_eh_info *ehi = &ap->eh_info; |
| int freeze = 0; |
| u32 irq_stat; |
| |
| /* on error, we need to clear IRQ explicitly */ |
| irq_stat = readl(port + PORT_IRQ_STAT); |
| writel(irq_stat, port + PORT_IRQ_STAT); |
| |
| /* first, analyze and record host port events */ |
| ata_ehi_clear_desc(ehi); |
| |
| ata_ehi_push_desc(ehi, "irq_stat 0x%08x", irq_stat); |
| |
| if (irq_stat & (PORT_IRQ_PHYRDY_CHG | PORT_IRQ_DEV_XCHG)) { |
| ata_ehi_hotplugged(ehi); |
| ata_ehi_push_desc(ehi, ", %s", |
| irq_stat & PORT_IRQ_PHYRDY_CHG ? |
| "PHY RDY changed" : "device exchanged"); |
| freeze = 1; |
| } |
| |
| if (irq_stat & PORT_IRQ_UNK_FIS) { |
| ehi->err_mask |= AC_ERR_HSM; |
| ehi->action |= ATA_EH_SOFTRESET; |
| ata_ehi_push_desc(ehi , ", unknown FIS"); |
| freeze = 1; |
| } |
| |
| /* deal with command error */ |
| if (irq_stat & PORT_IRQ_ERROR) { |
| struct sil24_cerr_info *ci = NULL; |
| unsigned int err_mask = 0, action = 0; |
| struct ata_queued_cmd *qc; |
| u32 cerr; |
| |
| /* analyze CMD_ERR */ |
| cerr = readl(port + PORT_CMD_ERR); |
| if (cerr < ARRAY_SIZE(sil24_cerr_db)) |
| ci = &sil24_cerr_db[cerr]; |
| |
| if (ci && ci->desc) { |
| err_mask |= ci->err_mask; |
| action |= ci->action; |
| ata_ehi_push_desc(ehi, ", %s", ci->desc); |
| } else { |
| err_mask |= AC_ERR_OTHER; |
| action |= ATA_EH_SOFTRESET; |
| ata_ehi_push_desc(ehi, ", unknown command error %d", |
| cerr); |
| } |
| |
| /* record error info */ |
| qc = ata_qc_from_tag(ap, ap->active_tag); |
| if (qc) { |
| sil24_update_tf(ap); |
| qc->err_mask |= err_mask; |
| } else |
| ehi->err_mask |= err_mask; |
| |
| ehi->action |= action; |
| } |
| |
| /* freeze or abort */ |
| if (freeze) |
| ata_port_freeze(ap); |
| else |
| ata_port_abort(ap); |
| } |
| |
| static void sil24_finish_qc(struct ata_queued_cmd *qc) |
| { |
| if (qc->flags & ATA_QCFLAG_RESULT_TF) |
| sil24_update_tf(qc->ap); |
| } |
| |
| static inline void sil24_host_intr(struct ata_port *ap) |
| { |
| void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; |
| u32 slot_stat, qc_active; |
| int rc; |
| |
| slot_stat = readl(port + PORT_SLOT_STAT); |
| |
| if (unlikely(slot_stat & HOST_SSTAT_ATTN)) { |
| sil24_error_intr(ap); |
| return; |
| } |
| |
| if (ap->flags & SIL24_FLAG_PCIX_IRQ_WOC) |
| writel(PORT_IRQ_COMPLETE, port + PORT_IRQ_STAT); |
| |
| qc_active = slot_stat & ~HOST_SSTAT_ATTN; |
| rc = ata_qc_complete_multiple(ap, qc_active, sil24_finish_qc); |
| if (rc > 0) |
| return; |
| if (rc < 0) { |
| struct ata_eh_info *ehi = &ap->eh_info; |
| ehi->err_mask |= AC_ERR_HSM; |
| ehi->action |= ATA_EH_SOFTRESET; |
| ata_port_freeze(ap); |
| return; |
| } |
| |
| if (ata_ratelimit()) |
| ata_port_printk(ap, KERN_INFO, "spurious interrupt " |
| "(slot_stat 0x%x active_tag %d sactive 0x%x)\n", |
| slot_stat, ap->active_tag, ap->sactive); |
| } |
| |
| static irqreturn_t sil24_interrupt(int irq, void *dev_instance, struct pt_regs *regs) |
| { |
| struct ata_host *host = dev_instance; |
| struct sil24_host_priv *hpriv = host->private_data; |
| unsigned handled = 0; |
| u32 status; |
| int i; |
| |
| status = readl(hpriv->host_base + HOST_IRQ_STAT); |
| |
| if (status == 0xffffffff) { |
| printk(KERN_ERR DRV_NAME ": IRQ status == 0xffffffff, " |
| "PCI fault or device removal?\n"); |
| goto out; |
| } |
| |
| if (!(status & IRQ_STAT_4PORTS)) |
| goto out; |
| |
| spin_lock(&host->lock); |
| |
| for (i = 0; i < host->n_ports; i++) |
| if (status & (1 << i)) { |
| struct ata_port *ap = host->ports[i]; |
| if (ap && !(ap->flags & ATA_FLAG_DISABLED)) { |
| sil24_host_intr(host->ports[i]); |
| handled++; |
| } else |
| printk(KERN_ERR DRV_NAME |
| ": interrupt from disabled port %d\n", i); |
| } |
| |
| spin_unlock(&host->lock); |
| out: |
| return IRQ_RETVAL(handled); |
| } |
| |
| static void sil24_error_handler(struct ata_port *ap) |
| { |
| struct ata_eh_context *ehc = &ap->eh_context; |
| |
| if (sil24_init_port(ap)) { |
| ata_eh_freeze_port(ap); |
| ehc->i.action |= ATA_EH_HARDRESET; |
| } |
| |
| /* perform recovery */ |
| ata_do_eh(ap, ata_std_prereset, sil24_softreset, sil24_hardreset, |
| ata_std_postreset); |
| } |
| |
| static void sil24_post_internal_cmd(struct ata_queued_cmd *qc) |
| { |
| struct ata_port *ap = qc->ap; |
| |
| if (qc->flags & ATA_QCFLAG_FAILED) |
| qc->err_mask |= AC_ERR_OTHER; |
| |
| /* make DMA engine forget about the failed command */ |
| if (qc->err_mask) |
| sil24_init_port(ap); |
| } |
| |
| static inline void sil24_cblk_free(struct sil24_port_priv *pp, struct device *dev) |
| { |
| const size_t cb_size = sizeof(*pp->cmd_block) * SIL24_MAX_CMDS; |
| |
| dma_free_coherent(dev, cb_size, pp->cmd_block, pp->cmd_block_dma); |
| } |
| |
| static int sil24_port_start(struct ata_port *ap) |
| { |
| struct device *dev = ap->host->dev; |
| struct sil24_port_priv *pp; |
| union sil24_cmd_block *cb; |
| size_t cb_size = sizeof(*cb) * SIL24_MAX_CMDS; |
| dma_addr_t cb_dma; |
| int rc = -ENOMEM; |
| |
| pp = kzalloc(sizeof(*pp), GFP_KERNEL); |
| if (!pp) |
| goto err_out; |
| |
| pp->tf.command = ATA_DRDY; |
| |
| cb = dma_alloc_coherent(dev, cb_size, &cb_dma, GFP_KERNEL); |
| if (!cb) |
| goto err_out_pp; |
| memset(cb, 0, cb_size); |
| |
| rc = ata_pad_alloc(ap, dev); |
| if (rc) |
| goto err_out_pad; |
| |
| pp->cmd_block = cb; |
| pp->cmd_block_dma = cb_dma; |
| |
| ap->private_data = pp; |
| |
| return 0; |
| |
| err_out_pad: |
| sil24_cblk_free(pp, dev); |
| err_out_pp: |
| kfree(pp); |
| err_out: |
| return rc; |
| } |
| |
| static void sil24_port_stop(struct ata_port *ap) |
| { |
| struct device *dev = ap->host->dev; |
| struct sil24_port_priv *pp = ap->private_data; |
| |
| sil24_cblk_free(pp, dev); |
| ata_pad_free(ap, dev); |
| kfree(pp); |
| } |
| |
| static void sil24_host_stop(struct ata_host *host) |
| { |
| struct sil24_host_priv *hpriv = host->private_data; |
| struct pci_dev *pdev = to_pci_dev(host->dev); |
| |
| pci_iounmap(pdev, hpriv->host_base); |
| pci_iounmap(pdev, hpriv->port_base); |
| kfree(hpriv); |
| } |
| |
| static void sil24_init_controller(struct pci_dev *pdev, int n_ports, |
| unsigned long port_flags, |
| void __iomem *host_base, |
| void __iomem *port_base) |
| { |
| u32 tmp; |
| int i; |
| |
| /* GPIO off */ |
| writel(0, host_base + HOST_FLASH_CMD); |
| |
| /* clear global reset & mask interrupts during initialization */ |
| writel(0, host_base + HOST_CTRL); |
| |
| /* init ports */ |
| for (i = 0; i < n_ports; i++) { |
| void __iomem *port = port_base + i * PORT_REGS_SIZE; |
| |
| /* Initial PHY setting */ |
| writel(0x20c, port + PORT_PHY_CFG); |
| |
| /* Clear port RST */ |
| tmp = readl(port + PORT_CTRL_STAT); |
| if (tmp & PORT_CS_PORT_RST) { |
| writel(PORT_CS_PORT_RST, port + PORT_CTRL_CLR); |
| tmp = ata_wait_register(port + PORT_CTRL_STAT, |
| PORT_CS_PORT_RST, |
| PORT_CS_PORT_RST, 10, 100); |
| if (tmp & PORT_CS_PORT_RST) |
| dev_printk(KERN_ERR, &pdev->dev, |
| "failed to clear port RST\n"); |
| } |
| |
| /* Configure IRQ WoC */ |
| if (port_flags & SIL24_FLAG_PCIX_IRQ_WOC) |
| writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_STAT); |
| else |
| writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_CLR); |
| |
| /* Zero error counters. */ |
| writel(0x8000, port + PORT_DECODE_ERR_THRESH); |
| writel(0x8000, port + PORT_CRC_ERR_THRESH); |
| writel(0x8000, port + PORT_HSHK_ERR_THRESH); |
| writel(0x0000, port + PORT_DECODE_ERR_CNT); |
| writel(0x0000, port + PORT_CRC_ERR_CNT); |
| writel(0x0000, port + PORT_HSHK_ERR_CNT); |
| |
| /* Always use 64bit activation */ |
| writel(PORT_CS_32BIT_ACTV, port + PORT_CTRL_CLR); |
| |
| /* Clear port multiplier enable and resume bits */ |
| writel(PORT_CS_PM_EN | PORT_CS_RESUME, port + PORT_CTRL_CLR); |
| } |
| |
| /* Turn on interrupts */ |
| writel(IRQ_STAT_4PORTS, host_base + HOST_CTRL); |
| } |
| |
| static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) |
| { |
| static int printed_version = 0; |
| unsigned int board_id = (unsigned int)ent->driver_data; |
| struct ata_port_info *pinfo = &sil24_port_info[board_id]; |
| struct ata_probe_ent *probe_ent = NULL; |
| struct sil24_host_priv *hpriv = NULL; |
| void __iomem *host_base = NULL; |
| void __iomem *port_base = NULL; |
| int i, rc; |
| u32 tmp; |
| |
| if (!printed_version++) |
| dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n"); |
| |
| rc = pci_enable_device(pdev); |
| if (rc) |
| return rc; |
| |
| rc = pci_request_regions(pdev, DRV_NAME); |
| if (rc) |
| goto out_disable; |
| |
| rc = -ENOMEM; |
| /* map mmio registers */ |
| host_base = pci_iomap(pdev, 0, 0); |
| if (!host_base) |
| goto out_free; |
| port_base = pci_iomap(pdev, 2, 0); |
| if (!port_base) |
| goto out_free; |
| |
| /* allocate & init probe_ent and hpriv */ |
| probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL); |
| if (!probe_ent) |
| goto out_free; |
| |
| hpriv = kzalloc(sizeof(*hpriv), GFP_KERNEL); |
| if (!hpriv) |
| goto out_free; |
| |
| probe_ent->dev = pci_dev_to_dev(pdev); |
| INIT_LIST_HEAD(&probe_ent->node); |
| |
| probe_ent->sht = pinfo->sht; |
| probe_ent->port_flags = pinfo->flags; |
| probe_ent->pio_mask = pinfo->pio_mask; |
| probe_ent->mwdma_mask = pinfo->mwdma_mask; |
| probe_ent->udma_mask = pinfo->udma_mask; |
| probe_ent->port_ops = pinfo->port_ops; |
| probe_ent->n_ports = SIL24_FLAG2NPORTS(pinfo->flags); |
| |
| probe_ent->irq = pdev->irq; |
| probe_ent->irq_flags = IRQF_SHARED; |
| probe_ent->private_data = hpriv; |
| |
| hpriv->host_base = host_base; |
| hpriv->port_base = port_base; |
| |
| /* |
| * Configure the device |
| */ |
| if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) { |
| rc = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK); |
| if (rc) { |
| rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK); |
| if (rc) { |
| dev_printk(KERN_ERR, &pdev->dev, |
| "64-bit DMA enable failed\n"); |
| goto out_free; |
| } |
| } |
| } else { |
| rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK); |
| if (rc) { |
| dev_printk(KERN_ERR, &pdev->dev, |
| "32-bit DMA enable failed\n"); |
| goto out_free; |
| } |
| rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK); |
| if (rc) { |
| dev_printk(KERN_ERR, &pdev->dev, |
| "32-bit consistent DMA enable failed\n"); |
| goto out_free; |
| } |
| } |
| |
| /* Apply workaround for completion IRQ loss on PCI-X errata */ |
| if (probe_ent->port_flags & SIL24_FLAG_PCIX_IRQ_WOC) { |
| tmp = readl(host_base + HOST_CTRL); |
| if (tmp & (HOST_CTRL_TRDY | HOST_CTRL_STOP | HOST_CTRL_DEVSEL)) |
| dev_printk(KERN_INFO, &pdev->dev, |
| "Applying completion IRQ loss on PCI-X " |
| "errata fix\n"); |
| else |
| probe_ent->port_flags &= ~SIL24_FLAG_PCIX_IRQ_WOC; |
| } |
| |
| for (i = 0; i < probe_ent->n_ports; i++) { |
| unsigned long portu = |
| (unsigned long)port_base + i * PORT_REGS_SIZE; |
| |
| probe_ent->port[i].cmd_addr = portu; |
| probe_ent->port[i].scr_addr = portu + PORT_SCONTROL; |
| |
| ata_std_ports(&probe_ent->port[i]); |
| } |
| |
| sil24_init_controller(pdev, probe_ent->n_ports, probe_ent->port_flags, |
| host_base, port_base); |
| |
| pci_set_master(pdev); |
| |
| /* FIXME: check ata_device_add return value */ |
| ata_device_add(probe_ent); |
| |
| kfree(probe_ent); |
| return 0; |
| |
| out_free: |
| if (host_base) |
| pci_iounmap(pdev, host_base); |
| if (port_base) |
| pci_iounmap(pdev, port_base); |
| kfree(probe_ent); |
| kfree(hpriv); |
| pci_release_regions(pdev); |
| out_disable: |
| pci_disable_device(pdev); |
| return rc; |
| } |
| |
| #ifdef CONFIG_PM |
| static int sil24_pci_device_resume(struct pci_dev *pdev) |
| { |
| struct ata_host *host = dev_get_drvdata(&pdev->dev); |
| struct sil24_host_priv *hpriv = host->private_data; |
| |
| ata_pci_device_do_resume(pdev); |
| |
| if (pdev->dev.power.power_state.event == PM_EVENT_SUSPEND) |
| writel(HOST_CTRL_GLOBAL_RST, hpriv->host_base + HOST_CTRL); |
| |
| sil24_init_controller(pdev, host->n_ports, host->ports[0]->flags, |
| hpriv->host_base, hpriv->port_base); |
| |
| ata_host_resume(host); |
| |
| return 0; |
| } |
| #endif |
| |
| static int __init sil24_init(void) |
| { |
| return pci_register_driver(&sil24_pci_driver); |
| } |
| |
| static void __exit sil24_exit(void) |
| { |
| pci_unregister_driver(&sil24_pci_driver); |
| } |
| |
| MODULE_AUTHOR("Tejun Heo"); |
| MODULE_DESCRIPTION("Silicon Image 3124/3132 SATA low-level driver"); |
| MODULE_LICENSE("GPL"); |
| MODULE_DEVICE_TABLE(pci, sil24_pci_tbl); |
| |
| module_init(sil24_init); |
| module_exit(sil24_exit); |