serial: bfin_5xx: move resources into board files
Rather than maintain Kconfig entries where people have to enter raw
numbers and hardcode lists of addresses/pins in the driver itself,
push it all to platform resources. This lets us simplify the driver,
the Kconfig, and gives board porters greater flexibility.
In the process, we need to also start supporting the early platform
interface. Not a big deal, but it causes the patch to be bigger than
a simple resource relocation.
All the Blackfin boards already have their resources updated and in
place for this change.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index ec3c214..ce39357 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -776,24 +776,7 @@
bool "Enable UART0 hardware flow control"
depends on SERIAL_BFIN_UART0
help
- Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
- signal.
-
-config UART0_CTS_PIN
- int "UART0 CTS pin"
- depends on BFIN_UART0_CTSRTS && !BF548
- default 23
- help
- The default pin is GPIO_GP7.
- Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
-
-config UART0_RTS_PIN
- int "UART0 RTS pin"
- depends on BFIN_UART0_CTSRTS && !BF548
- default 22
- help
- The default pin is GPIO_GP6.
- Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+ Enable hardware flow control in the driver.
config SERIAL_BFIN_UART1
bool "Enable UART1"
@@ -805,22 +788,7 @@
bool "Enable UART1 hardware flow control"
depends on SERIAL_BFIN_UART1
help
- Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
- signal.
-
-config UART1_CTS_PIN
- int "UART1 CTS pin"
- depends on BFIN_UART1_CTSRTS && !BF548
- default -1
- help
- Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
-
-config UART1_RTS_PIN
- int "UART1 RTS pin"
- depends on BFIN_UART1_CTSRTS && !BF548
- default -1
- help
- Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+ Enable hardware flow control in the driver.
config SERIAL_BFIN_UART2
bool "Enable UART2"
@@ -832,22 +800,7 @@
bool "Enable UART2 hardware flow control"
depends on SERIAL_BFIN_UART2
help
- Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
- signal.
-
-config UART2_CTS_PIN
- int "UART2 CTS pin"
- depends on BFIN_UART2_CTSRTS && !BF548
- default -1
- help
- Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
-
-config UART2_RTS_PIN
- int "UART2 RTS pin"
- depends on BFIN_UART2_CTSRTS && !BF548
- default -1
- help
- Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+ Enable hardware flow control in the driver.
config SERIAL_BFIN_UART3
bool "Enable UART3"
@@ -859,22 +812,7 @@
bool "Enable UART3 hardware flow control"
depends on SERIAL_BFIN_UART3
help
- Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
- signal.
-
-config UART3_CTS_PIN
- int "UART3 CTS pin"
- depends on BFIN_UART3_CTSRTS && !BF548
- default -1
- help
- Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
-
-config UART3_RTS_PIN
- int "UART3 RTS pin"
- depends on BFIN_UART3_CTSRTS && !BF548
- default -1
- help
- Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+ Enable hardware flow control in the driver.
config SERIAL_IMX
bool "IMX serial port support"