| #ifndef __SOUND_OPL3_H |
| #define __SOUND_OPL3_H |
| |
| /* |
| * Definitions of the OPL-3 registers. |
| * |
| * Copyright (c) by Jaroslav Kysela <perex@suse.cz>, |
| * Hannu Savolainen 1993-1996 |
| * |
| * |
| * The OPL-3 mode is switched on by writing 0x01, to the offset 5 |
| * of the right side. |
| * |
| * Another special register at the right side is at offset 4. It contains |
| * a bit mask defining which voices are used as 4 OP voices. |
| * |
| * The percussive mode is implemented in the left side only. |
| * |
| * With the above exceptions the both sides can be operated independently. |
| * |
| * A 4 OP voice can be created by setting the corresponding |
| * bit at offset 4 of the right side. |
| * |
| * For example setting the rightmost bit (0x01) changes the |
| * first voice on the right side to the 4 OP mode. The fourth |
| * voice is made inaccessible. |
| * |
| * If a voice is set to the 2 OP mode, it works like 2 OP modes |
| * of the original YM3812 (AdLib). In addition the voice can |
| * be connected the left, right or both stereo channels. It can |
| * even be left unconnected. This works with 4 OP voices also. |
| * |
| * The stereo connection bits are located in the FEEDBACK_CONNECTION |
| * register of the voice (0xC0-0xC8). In 4 OP voices these bits are |
| * in the second half of the voice. |
| * |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA |
| * |
| */ |
| |
| #include "driver.h" |
| #include <linux/time.h> |
| #include <linux/mutex.h> |
| #include "core.h" |
| #include "hwdep.h" |
| #include "timer.h" |
| #include "seq_midi_emul.h" |
| #ifdef CONFIG_SND_SEQUENCER_OSS |
| #include "seq_oss.h" |
| #include "seq_oss_legacy.h" |
| #endif |
| #include "seq_device.h" |
| #include "ainstr_fm.h" |
| |
| /* |
| * Register numbers for the global registers |
| */ |
| |
| #define OPL3_REG_TEST 0x01 |
| #define OPL3_ENABLE_WAVE_SELECT 0x20 |
| |
| #define OPL3_REG_TIMER1 0x02 |
| #define OPL3_REG_TIMER2 0x03 |
| #define OPL3_REG_TIMER_CONTROL 0x04 /* Left side */ |
| #define OPL3_IRQ_RESET 0x80 |
| #define OPL3_TIMER1_MASK 0x40 |
| #define OPL3_TIMER2_MASK 0x20 |
| #define OPL3_TIMER1_START 0x01 |
| #define OPL3_TIMER2_START 0x02 |
| |
| #define OPL3_REG_CONNECTION_SELECT 0x04 /* Right side */ |
| #define OPL3_LEFT_4OP_0 0x01 |
| #define OPL3_LEFT_4OP_1 0x02 |
| #define OPL3_LEFT_4OP_2 0x04 |
| #define OPL3_RIGHT_4OP_0 0x08 |
| #define OPL3_RIGHT_4OP_1 0x10 |
| #define OPL3_RIGHT_4OP_2 0x20 |
| |
| #define OPL3_REG_MODE 0x05 /* Right side */ |
| #define OPL3_OPL3_ENABLE 0x01 /* OPL3 mode */ |
| #define OPL3_OPL4_ENABLE 0x02 /* OPL4 mode */ |
| |
| #define OPL3_REG_KBD_SPLIT 0x08 /* Left side */ |
| #define OPL3_COMPOSITE_SINE_WAVE_MODE 0x80 /* Don't use with OPL-3? */ |
| #define OPL3_KEYBOARD_SPLIT 0x40 |
| |
| #define OPL3_REG_PERCUSSION 0xbd /* Left side only */ |
| #define OPL3_TREMOLO_DEPTH 0x80 |
| #define OPL3_VIBRATO_DEPTH 0x40 |
| #define OPL3_PERCUSSION_ENABLE 0x20 |
| #define OPL3_BASSDRUM_ON 0x10 |
| #define OPL3_SNAREDRUM_ON 0x08 |
| #define OPL3_TOMTOM_ON 0x04 |
| #define OPL3_CYMBAL_ON 0x02 |
| #define OPL3_HIHAT_ON 0x01 |
| |
| /* |
| * Offsets to the register banks for operators. To get the |
| * register number just add the operator offset to the bank offset |
| * |
| * AM/VIB/EG/KSR/Multiple (0x20 to 0x35) |
| */ |
| #define OPL3_REG_AM_VIB 0x20 |
| #define OPL3_TREMOLO_ON 0x80 |
| #define OPL3_VIBRATO_ON 0x40 |
| #define OPL3_SUSTAIN_ON 0x20 |
| #define OPL3_KSR 0x10 /* Key scaling rate */ |
| #define OPL3_MULTIPLE_MASK 0x0f /* Frequency multiplier */ |
| |
| /* |
| * KSL/Total level (0x40 to 0x55) |
| */ |
| #define OPL3_REG_KSL_LEVEL 0x40 |
| #define OPL3_KSL_MASK 0xc0 /* Envelope scaling bits */ |
| #define OPL3_TOTAL_LEVEL_MASK 0x3f /* Strength (volume) of OP */ |
| |
| /* |
| * Attack / Decay rate (0x60 to 0x75) |
| */ |
| #define OPL3_REG_ATTACK_DECAY 0x60 |
| #define OPL3_ATTACK_MASK 0xf0 |
| #define OPL3_DECAY_MASK 0x0f |
| |
| /* |
| * Sustain level / Release rate (0x80 to 0x95) |
| */ |
| #define OPL3_REG_SUSTAIN_RELEASE 0x80 |
| #define OPL3_SUSTAIN_MASK 0xf0 |
| #define OPL3_RELEASE_MASK 0x0f |
| |
| /* |
| * Wave select (0xE0 to 0xF5) |
| */ |
| #define OPL3_REG_WAVE_SELECT 0xe0 |
| #define OPL3_WAVE_SELECT_MASK 0x07 |
| |
| /* |
| * Offsets to the register banks for voices. Just add to the |
| * voice number to get the register number. |
| * |
| * F-Number low bits (0xA0 to 0xA8). |
| */ |
| #define OPL3_REG_FNUM_LOW 0xa0 |
| |
| /* |
| * F-number high bits / Key on / Block (octave) (0xB0 to 0xB8) |
| */ |
| #define OPL3_REG_KEYON_BLOCK 0xb0 |
| #define OPL3_KEYON_BIT 0x20 |
| #define OPL3_BLOCKNUM_MASK 0x1c |
| #define OPL3_FNUM_HIGH_MASK 0x03 |
| |
| /* |
| * Feedback / Connection (0xc0 to 0xc8) |
| * |
| * These registers have two new bits when the OPL-3 mode |
| * is selected. These bits controls connecting the voice |
| * to the stereo channels. For 4 OP voices this bit is |
| * defined in the second half of the voice (add 3 to the |
| * register offset). |
| * |
| * For 4 OP voices the connection bit is used in the |
| * both halves (gives 4 ways to connect the operators). |
| */ |
| #define OPL3_REG_FEEDBACK_CONNECTION 0xc0 |
| #define OPL3_FEEDBACK_MASK 0x0e /* Valid just for 1st OP of a voice */ |
| #define OPL3_CONNECTION_BIT 0x01 |
| /* |
| * In the 4 OP mode there is four possible configurations how the |
| * operators can be connected together (in 2 OP modes there is just |
| * AM or FM). The 4 OP connection mode is defined by the rightmost |
| * bit of the FEEDBACK_CONNECTION (0xC0-0xC8) on the both halves. |
| * |
| * First half Second half Mode |
| * |
| * +---+ |
| * v | |
| * 0 0 >+-1-+--2--3--4--> |
| * |
| * |
| * |
| * +---+ |
| * | | |
| * 0 1 >+-1-+--2-+ |
| * |-> |
| * >--3----4-+ |
| * |
| * +---+ |
| * | | |
| * 1 0 >+-1-+-----+ |
| * |-> |
| * >--2--3--4-+ |
| * |
| * +---+ |
| * | | |
| * 1 1 >+-1-+--+ |
| * | |
| * >--2--3-+-> |
| * | |
| * >--4----+ |
| */ |
| #define OPL3_STEREO_BITS 0x30 /* OPL-3 only */ |
| #define OPL3_VOICE_TO_LEFT 0x10 |
| #define OPL3_VOICE_TO_RIGHT 0x20 |
| |
| /* |
| |
| */ |
| |
| #define OPL3_LEFT 0x0000 |
| #define OPL3_RIGHT 0x0100 |
| |
| #define OPL3_HW_AUTO 0x0000 |
| #define OPL3_HW_OPL2 0x0200 |
| #define OPL3_HW_OPL3 0x0300 |
| #define OPL3_HW_OPL3_SV 0x0301 /* S3 SonicVibes */ |
| #define OPL3_HW_OPL3_CS 0x0302 /* CS4232/CS4236+ */ |
| #define OPL3_HW_OPL3_FM801 0x0303 /* FM801 */ |
| #define OPL3_HW_OPL3_CS4281 0x0304 /* CS4281 */ |
| #define OPL3_HW_OPL4 0x0400 /* YMF278B/YMF295 */ |
| #define OPL3_HW_OPL4_ML 0x0401 /* YMF704/YMF721 */ |
| #define OPL3_HW_MASK 0xff00 |
| |
| #define MAX_OPL2_VOICES 9 |
| #define MAX_OPL3_VOICES 18 |
| |
| struct snd_opl3; |
| |
| /* |
| * A structure to keep track of each hardware voice |
| */ |
| struct snd_opl3_voice { |
| int state; /* status */ |
| #define SNDRV_OPL3_ST_OFF 0 /* Not playing */ |
| #define SNDRV_OPL3_ST_ON_2OP 1 /* 2op voice is allocated */ |
| #define SNDRV_OPL3_ST_ON_4OP 2 /* 4op voice is allocated */ |
| #define SNDRV_OPL3_ST_NOT_AVAIL -1 /* voice is not available */ |
| |
| unsigned int time; /* An allocation time */ |
| unsigned char note; /* Note currently assigned to this voice */ |
| |
| unsigned long note_off; /* note-off time */ |
| int note_off_check; /* check note-off time */ |
| |
| unsigned char keyon_reg; /* KON register shadow */ |
| |
| struct snd_midi_channel *chan; /* Midi channel for this note */ |
| }; |
| |
| struct snd_opl3 { |
| unsigned long l_port; |
| unsigned long r_port; |
| struct resource *res_l_port; |
| struct resource *res_r_port; |
| unsigned short hardware; |
| /* hardware access */ |
| void (*command) (struct snd_opl3 * opl3, unsigned short cmd, unsigned char val); |
| unsigned short timer_enable; |
| int seq_dev_num; /* sequencer device number */ |
| struct snd_timer *timer1; |
| struct snd_timer *timer2; |
| spinlock_t timer_lock; |
| |
| void *private_data; |
| void (*private_free)(struct snd_opl3 *); |
| |
| spinlock_t reg_lock; |
| struct snd_card *card; /* The card that this belongs to */ |
| int used; /* usage flag - exclusive */ |
| unsigned char fm_mode; /* OPL mode, see SNDRV_DM_FM_MODE_XXX */ |
| unsigned char rhythm; /* percussion mode flag */ |
| unsigned char max_voices; /* max number of voices */ |
| #if defined(CONFIG_SND_SEQUENCER) || defined(CONFIG_SND_SEQUENCER_MODULE) |
| #define SNDRV_OPL3_MODE_SYNTH 0 /* OSS - voices allocated by application */ |
| #define SNDRV_OPL3_MODE_SEQ 1 /* ALSA - driver handles voice allocation */ |
| int synth_mode; /* synth mode */ |
| int seq_client; |
| |
| struct snd_seq_device *seq_dev; /* sequencer device */ |
| struct snd_midi_channel_set * chset; |
| |
| #ifdef CONFIG_SND_SEQUENCER_OSS |
| struct snd_seq_device *oss_seq_dev; /* OSS sequencer device */ |
| struct snd_midi_channel_set * oss_chset; |
| #endif |
| |
| struct snd_seq_kinstr_ops fm_ops; |
| struct snd_seq_kinstr_list *ilist; |
| |
| struct snd_opl3_voice voices[MAX_OPL3_VOICES]; /* Voices (OPL3 'channel') */ |
| int use_time; /* allocation counter */ |
| |
| unsigned short connection_reg; /* connection reg shadow */ |
| unsigned char drum_reg; /* percussion reg shadow */ |
| |
| spinlock_t voice_lock; /* Lock for voice access */ |
| |
| struct timer_list tlist; /* timer for note-offs and effects */ |
| int sys_timer_status; /* system timer run status */ |
| spinlock_t sys_timer_lock; /* Lock for system timer access */ |
| #endif |
| struct mutex access_mutex; /* locking */ |
| }; |
| |
| /* opl3.c */ |
| void snd_opl3_interrupt(struct snd_hwdep * hw); |
| int snd_opl3_new(struct snd_card *card, unsigned short hardware, |
| struct snd_opl3 **ropl3); |
| int snd_opl3_init(struct snd_opl3 *opl3); |
| int snd_opl3_create(struct snd_card *card, |
| unsigned long l_port, unsigned long r_port, |
| unsigned short hardware, |
| int integrated, |
| struct snd_opl3 ** opl3); |
| int snd_opl3_timer_new(struct snd_opl3 * opl3, int timer1_dev, int timer2_dev); |
| int snd_opl3_hwdep_new(struct snd_opl3 * opl3, int device, int seq_device, |
| struct snd_hwdep ** rhwdep); |
| |
| /* opl3_synth */ |
| int snd_opl3_open(struct snd_hwdep * hw, struct file *file); |
| int snd_opl3_ioctl(struct snd_hwdep * hw, struct file *file, |
| unsigned int cmd, unsigned long arg); |
| int snd_opl3_release(struct snd_hwdep * hw, struct file *file); |
| |
| void snd_opl3_reset(struct snd_opl3 * opl3); |
| |
| #endif /* __SOUND_OPL3_H */ |