Neterion: Driver help file
- vxge driver help text file.
- No change from previous submission.
- Changes in previous submissions -
Removed the performance tuning section with instructions to disable
time stamps and change sysctl settings - Reported by Dave Miller
General clean up.
- Removed tx/rx_pause, exec_mode, tx_steering_type, rx_steering_type, gro,
intr_type, rx & tx max_indicate_pkts and exec_mode loadable parameters. The
driver default settings work well in most if not all cases. Another patch
to configure these parameters with ethtool will be released in the future -
Reported by Stephen Hemminger.
- Incorporated following fixes based on comments from Ben Hutchings
Removed references to earlier kernel versions.
Removed sections that are similar for all drivers -
Load/Unload
Identifying the adapter/interface
Boot time configuration
Removed loadable parameter -
NAPI - Napi is always enabled.
rx_steering_type & ring_blocks - The driver default settings
work well in most if not all cases. Another patch to configure
these parameters with ethtool will be released in the future.
Removed ethtool support section - No need to duplicate ethtool
docs here.
Removed Known Issue on SUSE 9 - Doesn't apply when using a
current kernel.
Removed Common Problems section - These don't apply to in-tree modules.
Removed Available Downloads section - Not sure this belongs in-tree.
Removed Copyright information - This notice doesn't belong in
the kernel.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/Documentation/networking/vxge.txt b/Documentation/networking/vxge.txt
new file mode 100644
index 0000000..d2e2997
--- /dev/null
+++ b/Documentation/networking/vxge.txt
@@ -0,0 +1,100 @@
+Neterion's (Formerly S2io) X3100 Series 10GbE PCIe Server Adapter Linux driver
+==============================================================================
+
+Contents
+--------
+
+1) Introduction
+2) Features supported
+3) Configurable driver parameters
+4) Troubleshooting
+
+1) Introduction:
+----------------
+This Linux driver supports all Neterion's X3100 series 10 GbE PCIe I/O
+Virtualized Server adapters.
+The X3100 series supports four modes of operation, configurable via
+firmware -
+ Single function mode
+ Multi function mode
+ SRIOV mode
+ MRIOV mode
+The functions share a 10GbE link and the pci-e bus, but hardly anything else
+inside the ASIC. Features like independent hw reset, statistics, bandwidth/
+priority allocation and guarantees, GRO, TSO, interrupt moderation etc are
+supported independently on each function.
+
+(See below for a complete list of features supported for both IPv4 and IPv6)
+
+2) Features supported:
+----------------------
+
+i) Single function mode (up to 17 queues)
+
+ii) Multi function mode (up to 17 functions)
+
+iii) PCI-SIG's I/O Virtualization
+ - Single Root mode: v1.0 (up to 17 functions)
+ - Multi-Root mode: v1.0 (up to 17 functions)
+
+iv) Jumbo frames
+ X3100 Series supports MTU up to 9600 bytes, modifiable using
+ ifconfig command.
+
+v) Offloads supported: (Enabled by default)
+ Checksum offload (TCP/UDP/IP) on transmit and receive paths
+ TCP Segmentation Offload (TSO) on transmit path
+ Generic Receive Offload (GRO) on receive path
+
+vi) MSI-X: (Enabled by default)
+ Resulting in noticeable performance improvement (up to 7% on certain
+ platforms).
+
+vii) NAPI: (Enabled by default)
+ For better Rx interrupt moderation.
+
+viii)RTH (Receive Traffic Hash): (Enabled by default)
+ Receive side steering for better scaling.
+
+ix) Statistics
+ Comprehensive MAC-level and software statistics displayed using
+ "ethtool -S" option.
+
+x) Multiple hardware queues: (Enabled by default)
+ Up to 17 hardware based transmit and receive data channels, with
+ multiple steering options (transmit multiqueue enabled by default).
+
+3) Configurable driver parameters:
+----------------------------------
+
+i) max_config_dev
+ Specifies maximum device functions to be enabled.
+ Valid range: 1-8
+
+ii) max_config_port
+ Specifies number of ports to be enabled.
+ Valid range: 1,2
+ Default: 1
+
+iii)max_config_vpath
+ Specifies maximum VPATH(s) configured for each device function.
+ Valid range: 1-17
+
+iv) vlan_tag_strip
+ Enables/disables vlan tag stripping from all received tagged frames that
+ are not replicated at the internal L2 switch.
+ Valid range: 0,1 (disabled, enabled respectively)
+ Default: 1
+
+v) addr_learn_en
+ Enable learning the mac address of the guest OS interface in
+ virtualization environment.
+ Valid range: 0,1 (disabled, enabled respectively)
+ Default: 0
+
+4) Troubleshooting:
+-------------------
+
+To resolve an issue with the source code or X3100 series adapter, please collect
+the statistics, register dumps using ethool, relevant logs and email them to
+support@neterion.com.