| taiko audio CODEC |
| |
| Required properties: |
| |
| - compatible : "qcom,taiko-slim-pgd" |
| - elemental-addr: codec slimbus slave PGD enumeration address.(48 bits) |
| |
| - qcom,cdc-reset-gpio: gpio used for codec SOC reset. |
| |
| - cdc-vdd-buck-supply: phandle of buck supply's regulator device tree node. |
| - qcom,cdc-vdd-buck-voltage: buck supply's voltage level min and max in mV. |
| - qcom,cdc-vdd-buck-current: buck supply's max current in mA. |
| |
| - cdc-vdd-tx-h-supply: phandle of tx-h supply's regulator device tree node. |
| - qcom,cdc-vdd-tx-h-voltage: tx-h supply's voltage level min and max in mV. |
| - qcom,cdc-vdd-tx-h-current: tx-h supply's max current in mA. |
| |
| - cdc-vdd-rx-h-supply: phandle of rx-h supply's regulator device tree node. |
| - qcom,cdc-vdd-rx-h-voltage: rx-h supply's voltage level min and max in mV. |
| - qcom,cdc-vdd-rx-h-current: rx-h supply's max current in mA. |
| |
| - cdc-vddpx-1-supply: phandle of px-1 supply's regulator device tree node. |
| - qcom,cdc-vddpx-1-voltage: px-1 supply's voltage level min and max in mV. |
| - qcom,cdc-vddpx-1-current: px-1 supply's max current in mA. |
| |
| - cdc-vdd-a-1p2v-supply: phandle of 1.2v supply's regulator device tree node. |
| - qcom,cdc-vdd-a-1p2v-voltage: 1.2v supply's voltage level min and max in mV. |
| - qcom,cdc-vdd-a-1p2v-current: 1.2v supply's max current in mA. |
| |
| - cdc-vddcx-1-supply: phandle of cx-1 supply's regulator device tree node. |
| - qcom,cdc-vddcx-1-voltage: cx-1 supply's voltage level min and max in mV. |
| - qcom,cdc-vddcx-1-current: cx-1 supply's max current in mA. |
| |
| - cdc-vddcx-2-supply: phandle of cx-2 supply's regulator device tree node. |
| - qcom,cdc-vddcx-2-voltage: cx-2 supply's voltage level min and max in mV. |
| - qcom,cdc-vddcx-2-current: cx-2 supply's max current in mA. |
| |
| - qcom,cdc-static-supplies: List of supplies to be enabled prior to codec |
| hardware probe. Supplies in this list will be |
| stay enabled. |
| |
| - qcom,cdc-micbias-ldoh-v - LDOH output in volts (should be 1.95 V and 3.00 V). |
| |
| - qcom,cdc-micbias-cfilt1-mv - cfilt1 output voltage in milli volts. |
| - qcom,cdc-micbias-cfilt2-mv - cfilt2 output voltage in milli volts. |
| - qcom,cdc-micbias-cfilt3-mv - cfilt3 output voltage in milli volts. |
| cfilt voltage can be set to max of qcom,cdc-micbias-ldoh-v - 0.15V. |
| |
| - qcom,cdc-micbias1-cfilt-sel = cfilt to use for micbias1 |
| (should be from 1 to 3). |
| - qcom,cdc-micbias2-cfilt-sel = cfilt to use for micbias2 |
| (should be from 1 to 3). |
| - qcom,cdc-micbias3-cfilt-sel = cfilt to use for micbias3 |
| (should be from 1 to 3). |
| - qcom,cdc-micbias4-cfilt-sel = cfilt to use for micbias4 |
| (should be from 1 to 3). |
| This value represents the connected CFLIT to MIC Bias. |
| |
| - qcom,cdc-micbias1-ext-cap: Boolean. Enable micbias 1 external capacitor mode. |
| - qcom,cdc-micbias2-ext-cap: Boolean. Enable micbias 2 external capacitor mode. |
| - qcom,cdc-micbias3-ext-cap: Boolean. Enable micbias 3 external capacitor mode. |
| - qcom,cdc-micbias4-ext-cap: Boolean. Enable micbias 4 external capacitor mode. |
| - qcom,cdc-mclk-clk-rate - Specifies the master clock rate in Hz required for |
| codec. |
| - qcom,cdc-slim-ifd-dev - namme of the codec slim interface device. |
| - qcom,cdc-slim-ifd-elemental-addr - codec slimbus slave interface device |
| enumeration address. |
| |
| Optional properties: |
| - cdc-dmic-sample-rate: Specifies the sample rate of digital mic in HZ. The |
| values for 9.6MHZ mclk can be 2400000 Hz, 3200000 Hz |
| and 4800000 Hz. The values for 12.288MHz mclk can be |
| 3072200 Hz, 4096000 Hz and 6144000 Hz. |
| |
| - qcom,cdc-on-demand-supplies: List of supplies which can be enabled |
| dynamically. |
| Supplies in this list are off by default. |
| |
| Example: |
| |
| taiko_codec { |
| compatible = "qcom,taiko-slim-pgd"; |
| elemental-addr = [00 01 A0 00 17 02]; |
| |
| qcom,cdc-reset-gpio = <&msmgpio 63 0>; |
| |
| cdc-vdd-buck-supply = <&pm8941_s2>; |
| qcom,cdc-vdd-buck-voltage = <2150000 2150000>; |
| qcom,cdc-vdd-buck-current = <500000>; |
| |
| cdc-vdd-tx-h-supply = <&pm8941_s3>; |
| qcom,cdc-vdd-tx-h-voltage = <1800000 1800000>; |
| qcom,cdc-vdd-tx-h-current = <200000>; |
| |
| cdc-vdd-rx-h-supply = <&pm8941_s3>; |
| qcom,cdc-vdd-rx-h-voltage = <1800000 1800000>; |
| qcom,cdc-vdd-rx-h-current = <200000>; |
| |
| cdc-vddpx-1-supply = <&pm8941_s3>; |
| qcom,cdc-vddpx-1-voltage = <1800000 1800000>; |
| qcom,cdc-vddpx-1-current = <5000>; |
| |
| cdc-vdd-a-1p2v-supply = <&pm8941_l1>; |
| qcom,cdc-vdd-a-1p2v-voltage = <1225000 1225000>; |
| qcom,cdc-vdd-a-1p2v-current = <5000>; |
| |
| cdc-vddcx-1-supply = <&pm8941_l1>; |
| qcom,cdc-vddcx-1-voltage = <1225000 1225000>; |
| qcom,cdc-vddcx-1-current = <5000>; |
| |
| cdc-vddcx-2-supply = <&pm8941_l1>; |
| qcom,cdc-vddcx-2-voltage = <1225000 1225000>; |
| qcom,cdc-vddcx-2-current = <5000>; |
| |
| qcom,cdc-static-supplies = "cdc-vdd-buck", |
| "cdc-vdd-tx-h", |
| "cdc-vdd-rx-h", |
| "cdc-vddpx-1", |
| "cdc-vdd-a-1p2v", |
| "cdc-vddcx-1", |
| "cdc-vddcx-2"; |
| |
| com,cdc-on-demand-supplies = "cdc-vdd-spkdrv"; |
| |
| qcom,cdc-micbias-ldoh-v = <0x3>; |
| qcom,cdc-micbias-cfilt1-mv = <1800>; |
| qcom,cdc-micbias-cfilt2-mv = <2700>; |
| qcom,cdc-micbias-cfilt3-mv = <1800>; |
| qcom,cdc-micbias1-cfilt-sel = <0x0>; |
| qcom,cdc-micbias2-cfilt-sel = <0x1>; |
| qcom,cdc-micbias3-cfilt-sel = <0x2>; |
| qcom,cdc-micbias4-cfilt-sel = <0x2>; |
| qcom,cdc-micbias1-ext-cap; |
| qcom,cdc-micbias2-ext-cap; |
| qcom,cdc-micbias3-ext-cap; |
| qcom,cdc-micbias4-ext-cap; |
| qcom,cdc-mclk-clk-rate = <9600000>; |
| qcom,cdc-slim-ifd = "taiko-slim-ifd"; |
| qcom,cdc-slim-ifd-elemental-addr = [00 00 A0 00 17 02]; |
| qcom,cdc-dmic-sample-rate = <4800000>; |
| }; |
| |
| Wcd9xxx audio CODEC in I2C mode |
| |
| - compatible = "qcom,wcd9xxx-i2c-device"; |
| - reg: represents the slave address provided to the I2C driver. |
| - qcom,cdc-reset-gpio: gpio used for codec SOC reset. |
| |
| - cdc-vdd-buck-supply: phandle of buck supply's regulator device tree node. |
| - qcom,cdc-vdd-buck-voltage: buck supply's voltage level min and max in mV. |
| - qcom,cdc-vdd-buck-current: buck supply's max current in mA. |
| |
| - cdc-vdd-tx-h-supply: phandle of tx-h supply's regulator device tree node. |
| - qcom,cdc-vdd-tx-h-voltage: tx-h supply's voltage level min and max in mV. |
| - qcom,cdc-vdd-tx-h-current: tx-h supply's max current in mA. |
| |
| - cdc-vdd-rx-h-supply: phandle of rx-h supply's regulator device tree node. |
| - qcom,cdc-vdd-rx-h-voltage: rx-h supply's voltage level min and max in mV. |
| - qcom,cdc-vdd-rx-h-current: rx-h supply's max current in mA. |
| |
| - cdc-vddpx-1-supply: phandle of px-1 supply's regulator device tree node. |
| - qcom,cdc-vddpx-1-voltage: px-1 supply's voltage level min and max in mV. |
| - qcom,cdc-vddpx-1-current: px-1 supply's max current in mA. |
| |
| - cdc-vdd-a-1p2v-supply: phandle of 1.2v supply's regulator device tree node. |
| - qcom,cdc-vdd-a-1p2v-voltage: 1.2v supply's voltage level min and max in mV. |
| - qcom,cdc-vdd-a-1p2v-current: 1.2v supply's max current in mA. |
| |
| - cdc-vddcx-1-supply: phandle of cx-1 supply's regulator device tree node. |
| - qcom,cdc-vddcx-1-voltage: cx-1 supply's voltage level min and max in mV. |
| - qcom,cdc-vddcx-1-current: cx-1 supply's max current in mA. |
| |
| - cdc-vddcx-2-supply: phandle of cx-2 supply's regulator device tree node. |
| - qcom,cdc-vddcx-2-voltage: cx-2 supply's voltage level min and max in mV. |
| - qcom,cdc-vddcx-2-current: cx-2 supply's max current in mA. |
| |
| - qcom,cdc-static-supplies: List of supplies to be enabled prior to codec |
| hardware probe. Supplies in this list will be |
| stay enabled. |
| |
| - qcom,cdc-micbias-ldoh-v - LDOH output in volts (should be 1.95 V and 3.00 V). |
| |
| - qcom,cdc-micbias-cfilt1-mv - cfilt1 output voltage in milli volts. |
| - qcom,cdc-micbias-cfilt2-mv - cfilt2 output voltage in milli volts. |
| - qcom,cdc-micbias-cfilt3-mv - cfilt3 output voltage in milli volts. |
| cfilt voltage can be set to max of qcom,cdc-micbias-ldoh-v - 0.15V. |
| |
| - qcom,cdc-micbias1-cfilt-sel = cfilt to use for micbias1 |
| (should be from 1 to 3). |
| - qcom,cdc-micbias2-cfilt-sel = cfilt to use for micbias2 |
| (should be from 1 to 3). |
| - qcom,cdc-micbias3-cfilt-sel = cfilt to use for micbias3 |
| (should be from 1 to 3). |
| - qcom,cdc-micbias4-cfilt-sel = cfilt to use for micbias4 |
| (should be from 1 to 3). |
| This value represents the connected CFLIT to MIC Bias. |
| |
| - qcom,cdc-micbias1-ext-cap: Boolean. Enable micbias 1 external capacitor mode. |
| - qcom,cdc-micbias2-ext-cap: Boolean. Enable micbias 2 external capacitor mode. |
| - qcom,cdc-micbias3-ext-cap: Boolean. Enable micbias 3 external capacitor mode. |
| - qcom,cdc-micbias4-ext-cap: Boolean. Enable micbias 4 external capacitor mode. |
| - qcom,cdc-mclk-clk-rate - Specifies the master clock rate in Hz required for |
| codec. |
| |
| Optional properties: |
| |
| - qcom,cdc-on-demand-supplies: List of supplies which can be enabled |
| dynamically. |
| Supplies in this list are off by default. |
| |
| Example: |
| i2c@f9925000 { |
| cell-index = <3>; |
| compatible = "qcom,i2c-qup"; |
| reg = <0xf9925000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg-names = "qup_phys_addr"; |
| interrupts = <0 97 0>; |
| interrupt-names = "qup_err_intr"; |
| qcom,i2c-bus-freq = <100000>; |
| qcom,i2c-src-freq = <24000000>; |
| |
| wcd9xxx_codec@0d{ |
| compatible = "qcom,wcd9xxx-i2c"; |
| reg = <0x0d>; |
| qcom,cdc-reset-gpio = <&msmgpio 22 0>; |
| interrupt-parent = <&wcd9xxx_intc>; |
| interrupts = <0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 |
| 20 21 22 23 24 25 26 27 28>; |
| |
| cdc-vdd-buck-supply = <&pm8019_l11>; |
| qcom,cdc-vdd-buck-voltage = <1800000 1800000>; |
| qcom,cdc-vdd-buck-current = <25000>; |
| |
| cdc-vdd-tx-h-supply = <&pm8019_l11>; |
| qcom,cdc-vdd-tx-h-voltage = <1800000 1800000>; |
| qcom,cdc-vdd-tx-h-current = <25000>; |
| |
| cdc-vdd-rx-h-supply = <&pm8019_l11>; |
| qcom,cdc-vdd-rx-h-voltage = <1800000 1800000>; |
| qcom,cdc-vdd-rx-h-current = <25000>; |
| |
| cdc-vddpx-1-supply = <&pm8019_l11>; |
| qcom,cdc-vddpx-1-voltage = <1800000 1800000>; |
| qcom,cdc-vddpx-1-current = <10000>; |
| |
| cdc-vdd-a-1p2v-supply = <&pm8019_l9>; |
| qcom,cdc-vdd-a-1p2v-voltage = <1200000 1200000>; |
| qcom,cdc-vdd-a-1p2v-current = <10000>; |
| |
| cdc-vddcx-1-supply = <&pm8019_l9>; |
| qcom,cdc-vddcx-1-voltage = <1200000 1200000>; |
| qcom,cdc-vddcx-1-current = <10000>; |
| |
| cdc-vddcx-2-supply = <&pm8019_l9>; |
| qcom,cdc-vddcx-2-voltage = <1200000 1200000>; |
| qcom,cdc-vddcx-2-current = <10000>; |
| |
| qcom,cdc-static-supplies = "cdc-vdd-buck", |
| "cdc-vdd-tx-h", |
| "cdc-vdd-rx-h", |
| "cdc-vddpx-1", |
| "cdc-vdd-a-1p2v", |
| "cdc-vddcx-1", |
| "cdc-vddcx-2"; |
| |
| com,cdc-on-demand-supplies = "cdc-vdd-spkdrv"; |
| |
| qcom,cdc-micbias-ldoh-v = <0x3>; |
| qcom,cdc-micbias-cfilt1-mv = <1800>; |
| qcom,cdc-micbias-cfilt2-mv = <2700>; |
| qcom,cdc-micbias-cfilt3-mv = <1800>; |
| qcom,cdc-micbias1-cfilt-sel = <0x0>; |
| qcom,cdc-micbias2-cfilt-sel = <0x1>; |
| qcom,cdc-micbias3-cfilt-sel = <0x2>; |
| qcom,cdc-micbias4-cfilt-sel = <0x2>; |
| qcom,cdc-mclk-clk-rate = <12288000>; |
| }; |
| |
| wcd9xxx_codec@77{ |
| compatible = "qcom,wcd9xxx-i2c"; |
| reg = <0x77>; |
| }; |
| |
| wcd9xxx_codec@66{ |
| compatible = "qcom,wcd9xxx-i2c"; |
| reg = <0x66>; |
| }; |
| wcd9xxx_codec@55{ |
| compatible = "qcom,wcd9xxx-i2c"; |
| reg = <0x55>; |
| }; |
| }; |