[ARM] 3950/1: AT91: Split up system header file
The AT91RM9200 system header file (at91rm9200_sys.h) has been split into
separate header files for each peripheral. This was necessary since
some of the system peripherals are also used on AT91SAM9260 and
AT91SAM9261.
The new SAM9-specific register bits have also been defined.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/include/asm-arm/arch-at91rm9200/at91_aic.h b/include/asm-arm/arch-at91rm9200/at91_aic.h
new file mode 100644
index 0000000..267e698
--- /dev/null
+++ b/include/asm-arm/arch-at91rm9200/at91_aic.h
@@ -0,0 +1,53 @@
+/*
+ * include/asm-arm/arch-at91rm9200/at91_aic.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * Advanced Interrupt Controller (AIC) - System peripherals registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91_AIC_H
+#define AT91_AIC_H
+
+#define AT91_AIC_SMR(n) (AT91_AIC + ((n) * 4)) /* Source Mode Registers 0-31 */
+#define AT91_AIC_PRIOR (7 << 0) /* Priority Level */
+#define AT91_AIC_SRCTYPE (3 << 5) /* Interrupt Source Type */
+#define AT91_AIC_SRCTYPE_LOW (0 << 5)
+#define AT91_AIC_SRCTYPE_FALLING (1 << 5)
+#define AT91_AIC_SRCTYPE_HIGH (2 << 5)
+#define AT91_AIC_SRCTYPE_RISING (3 << 5)
+
+#define AT91_AIC_SVR(n) (AT91_AIC + 0x80 + ((n) * 4)) /* Source Vector Registers 0-31 */
+#define AT91_AIC_IVR (AT91_AIC + 0x100) /* Interrupt Vector Register */
+#define AT91_AIC_FVR (AT91_AIC + 0x104) /* Fast Interrupt Vector Register */
+#define AT91_AIC_ISR (AT91_AIC + 0x108) /* Interrupt Status Register */
+#define AT91_AIC_IRQID (0x1f << 0) /* Current Interrupt Identifier */
+
+#define AT91_AIC_IPR (AT91_AIC + 0x10c) /* Interrupt Pending Register */
+#define AT91_AIC_IMR (AT91_AIC + 0x110) /* Interrupt Mask Register */
+#define AT91_AIC_CISR (AT91_AIC + 0x114) /* Core Interrupt Status Register */
+#define AT91_AIC_NFIQ (1 << 0) /* nFIQ Status */
+#define AT91_AIC_NIRQ (1 << 1) /* nIRQ Status */
+
+#define AT91_AIC_IECR (AT91_AIC + 0x120) /* Interrupt Enable Command Register */
+#define AT91_AIC_IDCR (AT91_AIC + 0x124) /* Interrupt Disable Command Register */
+#define AT91_AIC_ICCR (AT91_AIC + 0x128) /* Interrupt Clear Command Register */
+#define AT91_AIC_ISCR (AT91_AIC + 0x12c) /* Interrupt Set Command Register */
+#define AT91_AIC_EOICR (AT91_AIC + 0x130) /* End of Interrupt Command Register */
+#define AT91_AIC_SPU (AT91_AIC + 0x134) /* Spurious Interrupt Vector Register */
+#define AT91_AIC_DCR (AT91_AIC + 0x138) /* Debug Control Register */
+#define AT91_AIC_DCR_PROT (1 << 0) /* Protection Mode */
+#define AT91_AIC_DCR_GMSK (1 << 1) /* General Mask */
+
+#define AT91_AIC_FFER (AT91_AIC + 0x140) /* Fast Forcing Enable Register [SAM9 only] */
+#define AT91_AIC_FFDR (AT91_AIC + 0x144) /* Fast Forcing Disable Register [SAM9 only] */
+#define AT91_AIC_FFSR (AT91_AIC + 0x148) /* Fast Forcing Status Register [SAM9 only] */
+
+#endif
diff --git a/include/asm-arm/arch-at91rm9200/at91_dbgu.h b/include/asm-arm/arch-at91rm9200/at91_dbgu.h
new file mode 100644
index 0000000..e4b8b27
--- /dev/null
+++ b/include/asm-arm/arch-at91rm9200/at91_dbgu.h
@@ -0,0 +1,45 @@
+/*
+ * include/asm-arm/arch-at91rm9200/at91_dbgu.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * Debug Unit (DBGU) - System peripherals registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91_DBGU_H
+#define AT91_DBGU_H
+
+#define AT91_DBGU_CR (AT91_DBGU + 0x00) /* Control Register */
+#define AT91_DBGU_MR (AT91_DBGU + 0x04) /* Mode Register */
+#define AT91_DBGU_IER (AT91_DBGU + 0x08) /* Interrupt Enable Register */
+#define AT91_DBGU_TXRDY (1 << 1) /* Transmitter Ready */
+#define AT91_DBGU_TXEMPTY (1 << 9) /* Transmitter Empty */
+#define AT91_DBGU_IDR (AT91_DBGU + 0x0c) /* Interrupt Disable Register */
+#define AT91_DBGU_IMR (AT91_DBGU + 0x10) /* Interrupt Mask Register */
+#define AT91_DBGU_SR (AT91_DBGU + 0x14) /* Status Register */
+#define AT91_DBGU_RHR (AT91_DBGU + 0x18) /* Receiver Holding Register */
+#define AT91_DBGU_THR (AT91_DBGU + 0x1c) /* Transmitter Holding Register */
+#define AT91_DBGU_BRGR (AT91_DBGU + 0x20) /* Baud Rate Generator Register */
+
+#define AT91_DBGU_CIDR (AT91_DBGU + 0x40) /* Chip ID Register */
+#define AT91_DBGU_EXID (AT91_DBGU + 0x44) /* Chip ID Extension Register */
+#define AT91_CIDR_VERSION (0x1f << 0) /* Version of the Device */
+#define AT91_CIDR_EPROC (7 << 5) /* Embedded Processor */
+#define AT91_CIDR_NVPSIZ (0xf << 8) /* Nonvolatile Program Memory Size */
+#define AT91_CIDR_NVPSIZ2 (0xf << 12) /* Second Nonvolatile Program Memory Size */
+#define AT91_CIDR_SRAMSIZ (0xf << 16) /* Internal SRAM Size */
+#define AT91_CIDR_ARCH (0xff << 20) /* Architecture Identifier */
+#define AT91_CIDR_NVPTYP (7 << 28) /* Nonvolatile Program Memory Type */
+#define AT91_CIDR_EXT (1 << 31) /* Extension Flag */
+
+#define AT91_DBGU_FNR (AT91_DBGU + 0x48) /* Force NTRST Register [SAM9 only] */
+#define AT91_DBGU_FNTRST (1 << 0) /* Force NTRST */
+
+#endif
diff --git a/include/asm-arm/arch-at91rm9200/at91_pdc.h b/include/asm-arm/arch-at91rm9200/at91_pdc.h
new file mode 100644
index 0000000..79d6e02
--- /dev/null
+++ b/include/asm-arm/arch-at91rm9200/at91_pdc.h
@@ -0,0 +1,36 @@
+/*
+ * include/asm-arm/arch-at91rm9200/at91_pdc.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * Peripheral Data Controller (PDC) registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91_PDC_H
+#define AT91_PDC_H
+
+#define AT91_PDC_RPR 0x100 /* Receive Pointer Register */
+#define AT91_PDC_RCR 0x104 /* Receive Counter Register */
+#define AT91_PDC_TPR 0x108 /* Transmit Pointer Register */
+#define AT91_PDC_TCR 0x10c /* Transmit Counter Register */
+#define AT91_PDC_RNPR 0x110 /* Receive Next Pointer Register */
+#define AT91_PDC_RNCR 0x114 /* Receive Next Counter Register */
+#define AT91_PDC_TNPR 0x118 /* Transmit Next Pointer Register */
+#define AT91_PDC_TNCR 0x11c /* Transmit Next Counter Register */
+
+#define AT91_PDC_PTCR 0x120 /* Transfer Control Register */
+#define AT91_PDC_RXTEN (1 << 0) /* Receiver Transfer Enable */
+#define AT91_PDC_RXTDIS (1 << 1) /* Receiver Transfer Disable */
+#define AT91_PDC_TXTEN (1 << 8) /* Transmitter Transfer Enable */
+#define AT91_PDC_TXTDIS (1 << 9) /* Transmitter Transfer Disable */
+
+#define AT91_PDC_PTSR 0x124 /* Transfer Status Register */
+
+#endif
diff --git a/include/asm-arm/arch-at91rm9200/at91_pio.h b/include/asm-arm/arch-at91rm9200/at91_pio.h
new file mode 100644
index 0000000..680eaa1
--- /dev/null
+++ b/include/asm-arm/arch-at91rm9200/at91_pio.h
@@ -0,0 +1,49 @@
+/*
+ * include/asm-arm/arch-at91rm9200/at91_pio.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * Parallel I/O Controller (PIO) - System peripherals registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91_PIO_H
+#define AT91_PIO_H
+
+#define PIO_PER 0x00 /* Enable Register */
+#define PIO_PDR 0x04 /* Disable Register */
+#define PIO_PSR 0x08 /* Status Register */
+#define PIO_OER 0x10 /* Output Enable Register */
+#define PIO_ODR 0x14 /* Output Disable Register */
+#define PIO_OSR 0x18 /* Output Status Register */
+#define PIO_IFER 0x20 /* Glitch Input Filter Enable */
+#define PIO_IFDR 0x24 /* Glitch Input Filter Disable */
+#define PIO_IFSR 0x28 /* Glitch Input Filter Status */
+#define PIO_SODR 0x30 /* Set Output Data Register */
+#define PIO_CODR 0x34 /* Clear Output Data Register */
+#define PIO_ODSR 0x38 /* Output Data Status Register */
+#define PIO_PDSR 0x3c /* Pin Data Status Register */
+#define PIO_IER 0x40 /* Interrupt Enable Register */
+#define PIO_IDR 0x44 /* Interrupt Disable Register */
+#define PIO_IMR 0x48 /* Interrupt Mask Register */
+#define PIO_ISR 0x4c /* Interrupt Status Register */
+#define PIO_MDER 0x50 /* Multi-driver Enable Register */
+#define PIO_MDDR 0x54 /* Multi-driver Disable Register */
+#define PIO_MDSR 0x58 /* Multi-driver Status Register */
+#define PIO_PUDR 0x60 /* Pull-up Disable Register */
+#define PIO_PUER 0x64 /* Pull-up Enable Register */
+#define PIO_PUSR 0x68 /* Pull-up Status Register */
+#define PIO_ASR 0x70 /* Peripheral A Select Register */
+#define PIO_BSR 0x74 /* Peripheral B Select Register */
+#define PIO_ABSR 0x78 /* AB Status Register */
+#define PIO_OWER 0xa0 /* Output Write Enable Register */
+#define PIO_OWDR 0xa4 /* Output Write Disable Register */
+#define PIO_OWSR 0xa8 /* Output Write Status Register */
+
+#endif
diff --git a/include/asm-arm/arch-at91rm9200/at91_pmc.h b/include/asm-arm/arch-at91rm9200/at91_pmc.h
new file mode 100644
index 0000000..de8c3da
--- /dev/null
+++ b/include/asm-arm/arch-at91rm9200/at91_pmc.h
@@ -0,0 +1,92 @@
+/*
+ * include/asm-arm/arch-at91rm9200/at91_pmc.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * Power Management Controller (PMC) - System peripherals registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91_PMC_H
+#define AT91_PMC_H
+
+#define AT91_PMC_SCER (AT91_PMC + 0x00) /* System Clock Enable Register */
+#define AT91_PMC_SCDR (AT91_PMC + 0x04) /* System Clock Disable Register */
+
+#define AT91_PMC_SCSR (AT91_PMC + 0x08) /* System Clock Status Register */
+#define AT91_PMC_PCK (1 << 0) /* Processor Clock */
+#define AT91RM9200_PMC_UDP (1 << 1) /* USB Devcice Port Clock [AT91RM9200 only] */
+#define AT91RM9200_PMC_MCKUDP (1 << 2) /* USB Device Port Master Clock Automatic Disable on Suspend [AT91RM9200 only] */
+#define AT91RM9200_PMC_UHP (1 << 4) /* USB Host Port Clock [AT91RM9200 only] */
+#define AT91SAM926x_PMC_UHP (1 << 6) /* USB Host Port Clock [AT91SAM926x only] */
+#define AT91SAM926x_PMC_UDP (1 << 7) /* USB Devcice Port Clock [AT91SAM926x only] */
+#define AT91_PMC_PCK0 (1 << 8) /* Programmable Clock 0 */
+#define AT91_PMC_PCK1 (1 << 9) /* Programmable Clock 1 */
+#define AT91_PMC_PCK2 (1 << 10) /* Programmable Clock 2 */
+#define AT91_PMC_PCK3 (1 << 11) /* Programmable Clock 3 */
+#define AT91_PMC_HCK0 (1 << 16) /* AHB Clock (USB host) [AT91SAM9261 only] */
+#define AT91_PMC_HCK1 (1 << 17) /* AHB Clock (LCD) [AT91SAM9261 only] */
+
+#define AT91_PMC_PCER (AT91_PMC + 0x10) /* Peripheral Clock Enable Register */
+#define AT91_PMC_PCDR (AT91_PMC + 0x14) /* Peripheral Clock Disable Register */
+#define AT91_PMC_PCSR (AT91_PMC + 0x18) /* Peripheral Clock Status Register */
+
+#define AT91_CKGR_MOR (AT91_PMC + 0x20) /* Main Oscillator Register */
+#define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */
+#define AT91_PMC_OSCBYPASS (1 << 1) /* Oscillator Bypass [AT91SAM926x only] */
+#define AT91_PMC_OSCOUNT (0xff << 8) /* Main Oscillator Start-up Time */
+
+#define AT91_CKGR_MCFR (AT91_PMC + 0x24) /* Main Clock Frequency Register */
+#define AT91_PMC_MAINF (0xffff << 0) /* Main Clock Frequency */
+#define AT91_PMC_MAINRDY (1 << 16) /* Main Clock Ready */
+
+#define AT91_CKGR_PLLAR (AT91_PMC + 0x28) /* PLL A Register */
+#define AT91_CKGR_PLLBR (AT91_PMC + 0x2c) /* PLL B Register */
+#define AT91_PMC_DIV (0xff << 0) /* Divider */
+#define AT91_PMC_PLLCOUNT (0x3f << 8) /* PLL Counter */
+#define AT91_PMC_OUT (3 << 14) /* PLL Clock Frequency Range */
+#define AT91_PMC_MUL (0x7ff << 16) /* PLL Multiplier */
+#define AT91_PMC_USB96M (1 << 28) /* Divider by 2 Enable (PLLB only) */
+
+#define AT91_PMC_MCKR (AT91_PMC + 0x30) /* Master Clock Register */
+#define AT91_PMC_CSS (3 << 0) /* Master Clock Selection */
+#define AT91_PMC_CSS_SLOW (0 << 0)
+#define AT91_PMC_CSS_MAIN (1 << 0)
+#define AT91_PMC_CSS_PLLA (2 << 0)
+#define AT91_PMC_CSS_PLLB (3 << 0)
+#define AT91_PMC_PRES (7 << 2) /* Master Clock Prescaler */
+#define AT91_PMC_PRES_1 (0 << 2)
+#define AT91_PMC_PRES_2 (1 << 2)
+#define AT91_PMC_PRES_4 (2 << 2)
+#define AT91_PMC_PRES_8 (3 << 2)
+#define AT91_PMC_PRES_16 (4 << 2)
+#define AT91_PMC_PRES_32 (5 << 2)
+#define AT91_PMC_PRES_64 (6 << 2)
+#define AT91_PMC_MDIV (3 << 8) /* Master Clock Division */
+#define AT91_PMC_MDIV_1 (0 << 8)
+#define AT91_PMC_MDIV_2 (1 << 8)
+#define AT91_PMC_MDIV_3 (2 << 8)
+#define AT91_PMC_MDIV_4 (3 << 8)
+
+#define AT91_PMC_PCKR(n) (AT91_PMC + 0x40 + ((n) * 4)) /* Programmable Clock 0-3 Registers */
+
+#define AT91_PMC_IER (AT91_PMC + 0x60) /* Interrupt Enable Register */
+#define AT91_PMC_IDR (AT91_PMC + 0x64) /* Interrupt Disable Register */
+#define AT91_PMC_SR (AT91_PMC + 0x68) /* Status Register */
+#define AT91_PMC_MOSCS (1 << 0) /* MOSCS Flag */
+#define AT91_PMC_LOCKA (1 << 1) /* PLLA Lock */
+#define AT91_PMC_LOCKB (1 << 2) /* PLLB Lock */
+#define AT91_PMC_MCKRDY (1 << 3) /* Master Clock */
+#define AT91_PMC_PCK0RDY (1 << 8) /* Programmable Clock 0 */
+#define AT91_PMC_PCK1RDY (1 << 9) /* Programmable Clock 1 */
+#define AT91_PMC_PCK2RDY (1 << 10) /* Programmable Clock 2 */
+#define AT91_PMC_PCK3RDY (1 << 11) /* Programmable Clock 3 */
+#define AT91_PMC_IMR (AT91_PMC + 0x6c) /* Interrupt Mask Register */
+
+#endif
diff --git a/include/asm-arm/arch-at91rm9200/at91_rtc.h b/include/asm-arm/arch-at91rm9200/at91_rtc.h
new file mode 100644
index 0000000..6e5065d
--- /dev/null
+++ b/include/asm-arm/arch-at91rm9200/at91_rtc.h
@@ -0,0 +1,75 @@
+/*
+ * include/asm-arm/arch-at91rm9200/at91_rtc.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * Real Time Clock (RTC) - System peripheral registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91_RTC_H
+#define AT91_RTC_H
+
+#define AT91_RTC_CR (AT91_RTC + 0x00) /* Control Register */
+#define AT91_RTC_UPDTIM (1 << 0) /* Update Request Time Register */
+#define AT91_RTC_UPDCAL (1 << 1) /* Update Request Calendar Register */
+#define AT91_RTC_TIMEVSEL (3 << 8) /* Time Event Selection */
+#define AT91_RTC_TIMEVSEL_MINUTE (0 << 8)
+#define AT91_RTC_TIMEVSEL_HOUR (1 << 8)
+#define AT91_RTC_TIMEVSEL_DAY24 (2 << 8)
+#define AT91_RTC_TIMEVSEL_DAY12 (3 << 8)
+#define AT91_RTC_CALEVSEL (3 << 16) /* Calendar Event Selection */
+#define AT91_RTC_CALEVSEL_WEEK (0 << 16)
+#define AT91_RTC_CALEVSEL_MONTH (1 << 16)
+#define AT91_RTC_CALEVSEL_YEAR (2 << 16)
+
+#define AT91_RTC_MR (AT91_RTC + 0x04) /* Mode Register */
+#define AT91_RTC_HRMOD (1 << 0) /* 12/24 Hour Mode */
+
+#define AT91_RTC_TIMR (AT91_RTC + 0x08) /* Time Register */
+#define AT91_RTC_SEC (0x7f << 0) /* Current Second */
+#define AT91_RTC_MIN (0x7f << 8) /* Current Minute */
+#define AT91_RTC_HOUR (0x3f << 16) /* Current Hour */
+#define AT91_RTC_AMPM (1 << 22) /* Ante Meridiem Post Meridiem Indicator */
+
+#define AT91_RTC_CALR (AT91_RTC + 0x0c) /* Calendar Register */
+#define AT91_RTC_CENT (0x7f << 0) /* Current Century */
+#define AT91_RTC_YEAR (0xff << 8) /* Current Year */
+#define AT91_RTC_MONTH (0x1f << 16) /* Current Month */
+#define AT91_RTC_DAY (7 << 21) /* Current Day */
+#define AT91_RTC_DATE (0x3f << 24) /* Current Date */
+
+#define AT91_RTC_TIMALR (AT91_RTC + 0x10) /* Time Alarm Register */
+#define AT91_RTC_SECEN (1 << 7) /* Second Alarm Enable */
+#define AT91_RTC_MINEN (1 << 15) /* Minute Alarm Enable */
+#define AT91_RTC_HOUREN (1 << 23) /* Hour Alarm Enable */
+
+#define AT91_RTC_CALALR (AT91_RTC + 0x14) /* Calendar Alarm Register */
+#define AT91_RTC_MTHEN (1 << 23) /* Month Alarm Enable */
+#define AT91_RTC_DATEEN (1 << 31) /* Date Alarm Enable */
+
+#define AT91_RTC_SR (AT91_RTC + 0x18) /* Status Register */
+#define AT91_RTC_ACKUPD (1 << 0) /* Acknowledge for Update */
+#define AT91_RTC_ALARM (1 << 1) /* Alarm Flag */
+#define AT91_RTC_SECEV (1 << 2) /* Second Event */
+#define AT91_RTC_TIMEV (1 << 3) /* Time Event */
+#define AT91_RTC_CALEV (1 << 4) /* Calendar Event */
+
+#define AT91_RTC_SCCR (AT91_RTC + 0x1c) /* Status Clear Command Register */
+#define AT91_RTC_IER (AT91_RTC + 0x20) /* Interrupt Enable Register */
+#define AT91_RTC_IDR (AT91_RTC + 0x24) /* Interrupt Disable Register */
+#define AT91_RTC_IMR (AT91_RTC + 0x28) /* Interrupt Mask Register */
+
+#define AT91_RTC_VER (AT91_RTC + 0x2c) /* Valid Entry Register */
+#define AT91_RTC_NVTIM (1 << 0) /* Non valid Time */
+#define AT91_RTC_NVCAL (1 << 1) /* Non valid Calendar */
+#define AT91_RTC_NVTIMALR (1 << 2) /* Non valid Time Alarm */
+#define AT91_RTC_NVCALALR (1 << 3) /* Non valid Calendar Alarm */
+
+#endif
diff --git a/include/asm-arm/arch-at91rm9200/at91_st.h b/include/asm-arm/arch-at91rm9200/at91_st.h
new file mode 100644
index 0000000..2432ddf
--- /dev/null
+++ b/include/asm-arm/arch-at91rm9200/at91_st.h
@@ -0,0 +1,49 @@
+/*
+ * include/asm-arm/arch-at91rm9200/at91_st.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * System Timer (ST) - System peripherals registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91_ST_H
+#define AT91_ST_H
+
+#define AT91_ST_CR (AT91_ST + 0x00) /* Control Register */
+#define AT91_ST_WDRST (1 << 0) /* Watchdog Timer Restart */
+
+#define AT91_ST_PIMR (AT91_ST + 0x04) /* Period Interval Mode Register */
+#define AT91_ST_PIV (0xffff << 0) /* Period Interval Value */
+
+#define AT91_ST_WDMR (AT91_ST + 0x08) /* Watchdog Mode Register */
+#define AT91_ST_WDV (0xffff << 0) /* Watchdog Counter Value */
+#define AT91_ST_RSTEN (1 << 16) /* Reset Enable */
+#define AT91_ST_EXTEN (1 << 17) /* External Signal Assertion Enable */
+
+#define AT91_ST_RTMR (AT91_ST + 0x0c) /* Real-time Mode Register */
+#define AT91_ST_RTPRES (0xffff << 0) /* Real-time Prescalar Value */
+
+#define AT91_ST_SR (AT91_ST + 0x10) /* Status Register */
+#define AT91_ST_PITS (1 << 0) /* Period Interval Timer Status */
+#define AT91_ST_WDOVF (1 << 1) /* Watchdog Overflow */
+#define AT91_ST_RTTINC (1 << 2) /* Real-time Timer Increment */
+#define AT91_ST_ALMS (1 << 3) /* Alarm Status */
+
+#define AT91_ST_IER (AT91_ST + 0x14) /* Interrupt Enable Register */
+#define AT91_ST_IDR (AT91_ST + 0x18) /* Interrupt Disable Register */
+#define AT91_ST_IMR (AT91_ST + 0x1c) /* Interrupt Mask Register */
+
+#define AT91_ST_RTAR (AT91_ST + 0x20) /* Real-time Alarm Register */
+#define AT91_ST_ALMV (0xfffff << 0) /* Alarm Value */
+
+#define AT91_ST_CRTR (AT91_ST + 0x24) /* Current Real-time Register */
+#define AT91_ST_CRTV (0xfffff << 0) /* Current Real-Time Value */
+
+#endif
diff --git a/include/asm-arm/arch-at91rm9200/at91rm9200_mc.h b/include/asm-arm/arch-at91rm9200/at91rm9200_mc.h
new file mode 100644
index 0000000..0c0d814
--- /dev/null
+++ b/include/asm-arm/arch-at91rm9200/at91rm9200_mc.h
@@ -0,0 +1,160 @@
+/*
+ * include/asm-arm/arch-at91rm9200/at91rm9200_mc.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * Memory Controllers (MC, EBI, SMC, SDRAMC, BFC) - System peripherals registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91RM9200_MC_H
+#define AT91RM9200_MC_H
+
+/* Memory Controller */
+#define AT91_MC_RCR (AT91_MC + 0x00) /* MC Remap Control Register */
+#define AT91_MC_RCB (1 << 0) /* Remap Command Bit */
+
+#define AT91_MC_ASR (AT91_MC + 0x04) /* MC Abort Status Register */
+#define AT91_MC_UNADD (1 << 0) /* Undefined Address Abort Status */
+#define AT91_MC_MISADD (1 << 1) /* Misaligned Address Abort Status */
+#define AT91_MC_ABTSZ (3 << 8) /* Abort Size Status */
+#define AT91_MC_ABTSZ_BYTE (0 << 8)
+#define AT91_MC_ABTSZ_HALFWORD (1 << 8)
+#define AT91_MC_ABTSZ_WORD (2 << 8)
+#define AT91_MC_ABTTYP (3 << 10) /* Abort Type Status */
+#define AT91_MC_ABTTYP_DATAREAD (0 << 10)
+#define AT91_MC_ABTTYP_DATAWRITE (1 << 10)
+#define AT91_MC_ABTTYP_FETCH (2 << 10)
+#define AT91_MC_MST0 (1 << 16) /* ARM920T Abort Source */
+#define AT91_MC_MST1 (1 << 17) /* PDC Abort Source */
+#define AT91_MC_MST2 (1 << 18) /* UHP Abort Source */
+#define AT91_MC_MST3 (1 << 19) /* EMAC Abort Source */
+#define AT91_MC_SVMST0 (1 << 24) /* Saved ARM920T Abort Source */
+#define AT91_MC_SVMST1 (1 << 25) /* Saved PDC Abort Source */
+#define AT91_MC_SVMST2 (1 << 26) /* Saved UHP Abort Source */
+#define AT91_MC_SVMST3 (1 << 27) /* Saved EMAC Abort Source */
+
+#define AT91_MC_AASR (AT91_MC + 0x08) /* MC Abort Address Status Register */
+
+#define AT91_MC_MPR (AT91_MC + 0x0c) /* MC Master Priority Register */
+#define AT91_MPR_MSTP0 (7 << 0) /* ARM920T Priority */
+#define AT91_MPR_MSTP1 (7 << 4) /* PDC Priority */
+#define AT91_MPR_MSTP2 (7 << 8) /* UHP Priority */
+#define AT91_MPR_MSTP3 (7 << 12) /* EMAC Priority */
+
+/* External Bus Interface (EBI) registers */
+#define AT91_EBI_CSA (AT91_MC + 0x60) /* Chip Select Assignment Register */
+#define AT91_EBI_CS0A (1 << 0) /* Chip Select 0 Assignment */
+#define AT91_EBI_CS0A_SMC (0 << 0)
+#define AT91_EBI_CS0A_BFC (1 << 0)
+#define AT91_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */
+#define AT91_EBI_CS1A_SMC (0 << 1)
+#define AT91_EBI_CS1A_SDRAMC (1 << 1)
+#define AT91_EBI_CS3A (1 << 3) /* Chip Select 2 Assignment */
+#define AT91_EBI_CS3A_SMC (0 << 3)
+#define AT91_EBI_CS3A_SMC_SMARTMEDIA (1 << 3)
+#define AT91_EBI_CS4A (1 << 4) /* Chip Select 3 Assignment */
+#define AT91_EBI_CS4A_SMC (0 << 4)
+#define AT91_EBI_CS4A_SMC_COMPACTFLASH (1 << 4)
+#define AT91_EBI_CFGR (AT91_MC + 0x64) /* Configuration Register */
+#define AT91_EBI_DBPUC (1 << 0) /* Data Bus Pull-Up Configuration */
+
+/* Static Memory Controller (SMC) registers */
+#define AT91_SMC_CSR(n) (AT91_MC + 0x70 + ((n) * 4))/* SMC Chip Select Register */
+#define AT91_SMC_NWS (0x7f << 0) /* Number of Wait States */
+#define AT91_SMC_NWS_(x) ((x) << 0)
+#define AT91_SMC_WSEN (1 << 7) /* Wait State Enable */
+#define AT91_SMC_TDF (0xf << 8) /* Data Float Time */
+#define AT91_SMC_TDF_(x) ((x) << 8)
+#define AT91_SMC_BAT (1 << 12) /* Byte Access Type */
+#define AT91_SMC_DBW (3 << 13) /* Data Bus Width */
+#define AT91_SMC_DBW_16 (1 << 13)
+#define AT91_SMC_DBW_8 (2 << 13)
+#define AT91_SMC_DPR (1 << 15) /* Data Read Protocol */
+#define AT91_SMC_ACSS (3 << 16) /* Address to Chip Select Setup */
+#define AT91_SMC_ACSS_STD (0 << 16)
+#define AT91_SMC_ACSS_1 (1 << 16)
+#define AT91_SMC_ACSS_2 (2 << 16)
+#define AT91_SMC_ACSS_3 (3 << 16)
+#define AT91_SMC_RWSETUP (7 << 24) /* Read & Write Signal Time Setup */
+#define AT91_SMC_RWSETUP_(x) ((x) << 24)
+#define AT91_SMC_RWHOLD (7 << 28) /* Read & Write Signal Hold Time */
+#define AT91_SMC_RWHOLD_(x) ((x) << 28)
+
+/* SDRAM Controller registers */
+#define AT91_SDRAMC_MR (AT91_MC + 0x90) /* Mode Register */
+#define AT91_SDRAMC_MODE (0xf << 0) /* Command Mode */
+#define AT91_SDRAMC_MODE_NORMAL (0 << 0)
+#define AT91_SDRAMC_MODE_NOP (1 << 0)
+#define AT91_SDRAMC_MODE_PRECHARGE (2 << 0)
+#define AT91_SDRAMC_MODE_LMR (3 << 0)
+#define AT91_SDRAMC_MODE_REFRESH (4 << 0)
+#define AT91_SDRAMC_DBW (1 << 4) /* Data Bus Width */
+#define AT91_SDRAMC_DBW_32 (0 << 4)
+#define AT91_SDRAMC_DBW_16 (1 << 4)
+
+#define AT91_SDRAMC_TR (AT91_MC + 0x94) /* Refresh Timer Register */
+#define AT91_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Count */
+
+#define AT91_SDRAMC_CR (AT91_MC + 0x98) /* Configuration Register */
+#define AT91_SDRAMC_NC (3 << 0) /* Number of Column Bits */
+#define AT91_SDRAMC_NC_8 (0 << 0)
+#define AT91_SDRAMC_NC_9 (1 << 0)
+#define AT91_SDRAMC_NC_10 (2 << 0)
+#define AT91_SDRAMC_NC_11 (3 << 0)
+#define AT91_SDRAMC_NR (3 << 2) /* Number of Row Bits */
+#define AT91_SDRAMC_NR_11 (0 << 2)
+#define AT91_SDRAMC_NR_12 (1 << 2)
+#define AT91_SDRAMC_NR_13 (2 << 2)
+#define AT91_SDRAMC_NB (1 << 4) /* Number of Banks */
+#define AT91_SDRAMC_NB_2 (0 << 4)
+#define AT91_SDRAMC_NB_4 (1 << 4)
+#define AT91_SDRAMC_CAS (3 << 5) /* CAS Latency */
+#define AT91_SDRAMC_CAS_2 (2 << 5)
+#define AT91_SDRAMC_TWR (0xf << 7) /* Write Recovery Delay */
+#define AT91_SDRAMC_TRC (0xf << 11) /* Row Cycle Delay */
+#define AT91_SDRAMC_TRP (0xf << 15) /* Row Precharge Delay */
+#define AT91_SDRAMC_TRCD (0xf << 19) /* Row to Column Delay */
+#define AT91_SDRAMC_TRAS (0xf << 23) /* Active to Precharge Delay */
+#define AT91_SDRAMC_TXSR (0xf << 27) /* Exit Self Refresh to Active Delay */
+
+#define AT91_SDRAMC_SRR (AT91_MC + 0x9c) /* Self Refresh Register */
+#define AT91_SDRAMC_LPR (AT91_MC + 0xa0) /* Low Power Register */
+#define AT91_SDRAMC_IER (AT91_MC + 0xa4) /* Interrupt Enable Register */
+#define AT91_SDRAMC_IDR (AT91_MC + 0xa8) /* Interrupt Disable Register */
+#define AT91_SDRAMC_IMR (AT91_MC + 0xac) /* Interrupt Mask Register */
+#define AT91_SDRAMC_ISR (AT91_MC + 0xb0) /* Interrupt Status Register */
+
+/* Burst Flash Controller register */
+#define AT91_BFC_MR (AT91_MC + 0xc0) /* Mode Register */
+#define AT91_BFC_BFCOM (3 << 0) /* Burst Flash Controller Operating Mode */
+#define AT91_BFC_BFCOM_DISABLED (0 << 0)
+#define AT91_BFC_BFCOM_ASYNC (1 << 0)
+#define AT91_BFC_BFCOM_BURST (2 << 0)
+#define AT91_BFC_BFCC (3 << 2) /* Burst Flash Controller Clock */
+#define AT91_BFC_BFCC_MCK (1 << 2)
+#define AT91_BFC_BFCC_DIV2 (2 << 2)
+#define AT91_BFC_BFCC_DIV4 (3 << 2)
+#define AT91_BFC_AVL (0xf << 4) /* Address Valid Latency */
+#define AT91_BFC_PAGES (7 << 8) /* Page Size */
+#define AT91_BFC_PAGES_NO_PAGE (0 << 8)
+#define AT91_BFC_PAGES_16 (1 << 8)
+#define AT91_BFC_PAGES_32 (2 << 8)
+#define AT91_BFC_PAGES_64 (3 << 8)
+#define AT91_BFC_PAGES_128 (4 << 8)
+#define AT91_BFC_PAGES_256 (5 << 8)
+#define AT91_BFC_PAGES_512 (6 << 8)
+#define AT91_BFC_PAGES_1024 (7 << 8)
+#define AT91_BFC_OEL (3 << 12) /* Output Enable Latency */
+#define AT91_BFC_BAAEN (1 << 16) /* Burst Address Advance Enable */
+#define AT91_BFC_BFOEH (1 << 17) /* Burst Flash Output Enable Handling */
+#define AT91_BFC_MUXEN (1 << 18) /* Multiplexed Bus Enable */
+#define AT91_BFC_RDYEN (1 << 19) /* Ready Enable Mode */
+
+#endif
diff --git a/include/asm-arm/arch-at91rm9200/at91rm9200_sys.h b/include/asm-arm/arch-at91rm9200/at91rm9200_sys.h
deleted file mode 100644
index 73693fe..0000000
--- a/include/asm-arm/arch-at91rm9200/at91rm9200_sys.h
+++ /dev/null
@@ -1,438 +0,0 @@
-/*
- * include/asm-arm/arch-at91rm9200/at91rm9200_sys.h
- *
- * Copyright (C) 2005 Ivan Kokshaysky
- * Copyright (C) SAN People
- *
- * System peripherals registers.
- * Based on AT91RM9200 datasheet revision E.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91RM9200_SYS_H
-#define AT91RM9200_SYS_H
-
-/*
- * Advanced Interrupt Controller.
- */
-#define AT91_AIC 0x000
-
-#define AT91_AIC_SMR(n) (AT91_AIC + ((n) * 4)) /* Source Mode Registers 0-31 */
-#define AT91_AIC_PRIOR (7 << 0) /* Priority Level */
-#define AT91_AIC_SRCTYPE (3 << 5) /* Interrupt Source Type */
-#define AT91_AIC_SRCTYPE_LOW (0 << 5)
-#define AT91_AIC_SRCTYPE_FALLING (1 << 5)
-#define AT91_AIC_SRCTYPE_HIGH (2 << 5)
-#define AT91_AIC_SRCTYPE_RISING (3 << 5)
-
-#define AT91_AIC_SVR(n) (AT91_AIC + 0x80 + ((n) * 4)) /* Source Vector Registers 0-31 */
-#define AT91_AIC_IVR (AT91_AIC + 0x100) /* Interrupt Vector Register */
-#define AT91_AIC_FVR (AT91_AIC + 0x104) /* Fast Interrupt Vector Register */
-#define AT91_AIC_ISR (AT91_AIC + 0x108) /* Interrupt Status Register */
-#define AT91_AIC_IRQID (0x1f << 0) /* Current Interrupt Identifier */
-
-#define AT91_AIC_IPR (AT91_AIC + 0x10c) /* Interrupt Pending Register */
-#define AT91_AIC_IMR (AT91_AIC + 0x110) /* Interrupt Mask Register */
-#define AT91_AIC_CISR (AT91_AIC + 0x114) /* Core Interrupt Status Register */
-#define AT91_AIC_NFIQ (1 << 0) /* nFIQ Status */
-#define AT91_AIC_NIRQ (1 << 1) /* nIRQ Status */
-
-#define AT91_AIC_IECR (AT91_AIC + 0x120) /* Interrupt Enable Command Register */
-#define AT91_AIC_IDCR (AT91_AIC + 0x124) /* Interrupt Disable Command Register */
-#define AT91_AIC_ICCR (AT91_AIC + 0x128) /* Interrupt Clear Command Register */
-#define AT91_AIC_ISCR (AT91_AIC + 0x12c) /* Interrupt Set Command Register */
-#define AT91_AIC_EOICR (AT91_AIC + 0x130) /* End of Interrupt Command Register */
-#define AT91_AIC_SPU (AT91_AIC + 0x134) /* Spurious Interrupt Vector Register */
-#define AT91_AIC_DCR (AT91_AIC + 0x138) /* Debug Control Register */
-#define AT91_AIC_DCR_PROT (1 << 0) /* Protection Mode */
-#define AT91_AIC_DCR_GMSK (1 << 1) /* General Mask */
-
-
-/*
- * Debug Unit.
- */
-#define AT91_DBGU 0x200
-
-#define AT91_DBGU_CR (AT91_DBGU + 0x00) /* Control Register */
-#define AT91_DBGU_MR (AT91_DBGU + 0x04) /* Mode Register */
-#define AT91_DBGU_IER (AT91_DBGU + 0x08) /* Interrupt Enable Register */
-#define AT91_DBGU_TXRDY (1 << 1) /* Transmitter Ready */
-#define AT91_DBGU_TXEMPTY (1 << 9) /* Transmitter Empty */
-#define AT91_DBGU_IDR (AT91_DBGU + 0x0c) /* Interrupt Disable Register */
-#define AT91_DBGU_IMR (AT91_DBGU + 0x10) /* Interrupt Mask Register */
-#define AT91_DBGU_SR (AT91_DBGU + 0x14) /* Status Register */
-#define AT91_DBGU_RHR (AT91_DBGU + 0x18) /* Receiver Holding Register */
-#define AT91_DBGU_THR (AT91_DBGU + 0x1c) /* Transmitter Holding Register */
-#define AT91_DBGU_BRGR (AT91_DBGU + 0x20) /* Baud Rate Generator Register */
-
-#define AT91_DBGU_CIDR (AT91_DBGU + 0x40) /* Chip ID Register */
-#define AT91_DBGU_EXID (AT91_DBGU + 0x44) /* Chip ID Extension Register */
-#define AT91_CIDR_VERSION (0x1f << 0) /* Version of the Device */
-#define AT91_CIDR_EPROC (7 << 5) /* Embedded Processor */
-#define AT91_CIDR_NVPSIZ (0xf << 8) /* Nonvolatile Program Memory Size */
-#define AT91_CIDR_NVPSIZ2 (0xf << 12) /* Second Nonvolatile Program Memory Size */
-#define AT91_CIDR_SRAMSIZ (0xf << 16) /* Internal SRAM Size */
-#define AT91_CIDR_ARCH (0xff << 20) /* Architecture Identifier */
-#define AT91_CIDR_NVPTYP (7 << 28) /* Nonvolatile Program Memory Type */
-#define AT91_CIDR_EXT (1 << 31) /* Extension Flag */
-
-#define AT91_AIC_FFER (AT91_AIC + 0x140) /* Fast Forcing Enable Register [SAM9 only] */
-#define AT91_AIC_FFDR (AT91_AIC + 0x144) /* Fast Forcing Disable Register [SAM9 only] */
-#define AT91_AIC_FFSR (AT91_AIC + 0x148) /* Fast Forcing Status Register [SAM9 only] */
-
-/*
- * PIO Controllers.
- */
-#define AT91_PIOA 0x400
-#define AT91_PIOB 0x600
-#define AT91_PIOC 0x800
-#define AT91_PIOD 0xa00
-
-#define PIO_PER 0x00 /* Enable Register */
-#define PIO_PDR 0x04 /* Disable Register */
-#define PIO_PSR 0x08 /* Status Register */
-#define PIO_OER 0x10 /* Output Enable Register */
-#define PIO_ODR 0x14 /* Output Disable Register */
-#define PIO_OSR 0x18 /* Output Status Register */
-#define PIO_IFER 0x20 /* Glitch Input Filter Enable */
-#define PIO_IFDR 0x24 /* Glitch Input Filter Disable */
-#define PIO_IFSR 0x28 /* Glitch Input Filter Status */
-#define PIO_SODR 0x30 /* Set Output Data Register */
-#define PIO_CODR 0x34 /* Clear Output Data Register */
-#define PIO_ODSR 0x38 /* Output Data Status Register */
-#define PIO_PDSR 0x3c /* Pin Data Status Register */
-#define PIO_IER 0x40 /* Interrupt Enable Register */
-#define PIO_IDR 0x44 /* Interrupt Disable Register */
-#define PIO_IMR 0x48 /* Interrupt Mask Register */
-#define PIO_ISR 0x4c /* Interrupt Status Register */
-#define PIO_MDER 0x50 /* Multi-driver Enable Register */
-#define PIO_MDDR 0x54 /* Multi-driver Disable Register */
-#define PIO_MDSR 0x58 /* Multi-driver Status Register */
-#define PIO_PUDR 0x60 /* Pull-up Disable Register */
-#define PIO_PUER 0x64 /* Pull-up Enable Register */
-#define PIO_PUSR 0x68 /* Pull-up Status Register */
-#define PIO_ASR 0x70 /* Peripheral A Select Register */
-#define PIO_BSR 0x74 /* Peripheral B Select Register */
-#define PIO_ABSR 0x78 /* AB Status Register */
-#define PIO_OWER 0xa0 /* Output Write Enable Register */
-#define PIO_OWDR 0xa4 /* Output Write Disable Register */
-#define PIO_OWSR 0xa8 /* Output Write Status Register */
-
-#define AT91_PIO_P(n) (1 << (n))
-
-
-/*
- * Power Management Controller.
- */
-#define AT91_PMC 0xc00
-
-#define AT91_PMC_SCER (AT91_PMC + 0x00) /* System Clock Enable Register */
-#define AT91_PMC_SCDR (AT91_PMC + 0x04) /* System Clock Disable Register */
-
-#define AT91_PMC_SCSR (AT91_PMC + 0x08) /* System Clock Status Register */
-#define AT91_PMC_PCK (1 << 0) /* Processor Clock */
-#define AT91_PMC_UDP (1 << 1) /* USB Devcice Port Clock */
-#define AT91_PMC_MCKUDP (1 << 2) /* USB Device Port Master Clock Automatic Disable on Suspend */
-#define AT91_PMC_UHP (1 << 4) /* USB Host Port Clock */
-#define AT91_PMC_PCK0 (1 << 8) /* Programmable Clock 0 */
-#define AT91_PMC_PCK1 (1 << 9) /* Programmable Clock 1 */
-#define AT91_PMC_PCK2 (1 << 10) /* Programmable Clock 2 */
-#define AT91_PMC_PCK3 (1 << 11) /* Programmable Clock 3 */
-
-#define AT91_PMC_PCER (AT91_PMC + 0x10) /* Peripheral Clock Enable Register */
-#define AT91_PMC_PCDR (AT91_PMC + 0x14) /* Peripheral Clock Disable Register */
-#define AT91_PMC_PCSR (AT91_PMC + 0x18) /* Peripheral Clock Status Register */
-
-#define AT91_CKGR_MOR (AT91_PMC + 0x20) /* Main Oscillator Register */
-#define AT91_PMC_MOSCEN (1 << 0) /* Main Oscillator Enable */
-#define AT91_PMC_OSCOUNT (0xff << 8) /* Main Oscillator Start-up Time */
-
-#define AT91_CKGR_MCFR (AT91_PMC + 0x24) /* Main Clock Frequency Register */
-#define AT91_PMC_MAINF (0xffff << 0) /* Main Clock Frequency */
-#define AT91_PMC_MAINRDY (1 << 16) /* Main Clock Ready */
-
-#define AT91_CKGR_PLLAR (AT91_PMC + 0x28) /* PLL A Register */
-#define AT91_CKGR_PLLBR (AT91_PMC + 0x2c) /* PLL B Register */
-#define AT91_PMC_DIV (0xff << 0) /* Divider */
-#define AT91_PMC_PLLCOUNT (0x3f << 8) /* PLL Counter */
-#define AT91_PMC_OUT (3 << 14) /* PLL Clock Frequency Range */
-#define AT91_PMC_MUL (0x7ff << 16) /* PLL Multiplier */
-#define AT91_PMC_USB96M (1 << 28) /* Divider by 2 Enable (PLLB only) */
-
-#define AT91_PMC_MCKR (AT91_PMC + 0x30) /* Master Clock Register */
-#define AT91_PMC_CSS (3 << 0) /* Master Clock Selection */
-#define AT91_PMC_CSS_SLOW (0 << 0)
-#define AT91_PMC_CSS_MAIN (1 << 0)
-#define AT91_PMC_CSS_PLLA (2 << 0)
-#define AT91_PMC_CSS_PLLB (3 << 0)
-#define AT91_PMC_PRES (7 << 2) /* Master Clock Prescaler */
-#define AT91_PMC_PRES_1 (0 << 2)
-#define AT91_PMC_PRES_2 (1 << 2)
-#define AT91_PMC_PRES_4 (2 << 2)
-#define AT91_PMC_PRES_8 (3 << 2)
-#define AT91_PMC_PRES_16 (4 << 2)
-#define AT91_PMC_PRES_32 (5 << 2)
-#define AT91_PMC_PRES_64 (6 << 2)
-#define AT91_PMC_MDIV (3 << 8) /* Master Clock Division */
-#define AT91_PMC_MDIV_1 (0 << 8)
-#define AT91_PMC_MDIV_2 (1 << 8)
-#define AT91_PMC_MDIV_3 (2 << 8)
-#define AT91_PMC_MDIV_4 (3 << 8)
-
-#define AT91_PMC_PCKR(n) (AT91_PMC + 0x40 + ((n) * 4)) /* Programmable Clock 0-3 Registers */
-
-#define AT91_PMC_IER (AT91_PMC + 0x60) /* Interrupt Enable Register */
-#define AT91_PMC_IDR (AT91_PMC + 0x64) /* Interrupt Disable Register */
-#define AT91_PMC_SR (AT91_PMC + 0x68) /* Status Register */
-#define AT91_PMC_MOSCS (1 << 0) /* MOSCS Flag */
-#define AT91_PMC_LOCKA (1 << 1) /* PLLA Lock */
-#define AT91_PMC_LOCKB (1 << 2) /* PLLB Lock */
-#define AT91_PMC_MCKRDY (1 << 3) /* Master Clock */
-#define AT91_PMC_PCK0RDY (1 << 8) /* Programmable Clock 0 */
-#define AT91_PMC_PCK1RDY (1 << 9) /* Programmable Clock 1 */
-#define AT91_PMC_PCK2RDY (1 << 10) /* Programmable Clock 2 */
-#define AT91_PMC_PCK3RDY (1 << 11) /* Programmable Clock 3 */
-#define AT91_PMC_IMR (AT91_PMC + 0x6c) /* Interrupt Mask Register */
-
-
-/*
- * System Timer.
- */
-#define AT91_ST 0xd00
-
-#define AT91_ST_CR (AT91_ST + 0x00) /* Control Register */
-#define AT91_ST_WDRST (1 << 0) /* Watchdog Timer Restart */
-#define AT91_ST_PIMR (AT91_ST + 0x04) /* Period Interval Mode Register */
-#define AT91_ST_PIV (0xffff << 0) /* Period Interval Value */
-#define AT91_ST_WDMR (AT91_ST + 0x08) /* Watchdog Mode Register */
-#define AT91_ST_WDV (0xffff << 0) /* Watchdog Counter Value */
-#define AT91_ST_RSTEN (1 << 16) /* Reset Enable */
-#define AT91_ST_EXTEN (1 << 17) /* External Signal Assertion Enable */
-#define AT91_ST_RTMR (AT91_ST + 0x0c) /* Real-time Mode Register */
-#define AT91_ST_RTPRES (0xffff << 0) /* Real-time Prescalar Value */
-#define AT91_ST_SR (AT91_ST + 0x10) /* Status Register */
-#define AT91_ST_PITS (1 << 0) /* Period Interval Timer Status */
-#define AT91_ST_WDOVF (1 << 1) /* Watchdog Overflow */
-#define AT91_ST_RTTINC (1 << 2) /* Real-time Timer Increment */
-#define AT91_ST_ALMS (1 << 3) /* Alarm Status */
-#define AT91_ST_IER (AT91_ST + 0x14) /* Interrupt Enable Register */
-#define AT91_ST_IDR (AT91_ST + 0x18) /* Interrupt Disable Register */
-#define AT91_ST_IMR (AT91_ST + 0x1c) /* Interrupt Mask Register */
-#define AT91_ST_RTAR (AT91_ST + 0x20) /* Real-time Alarm Register */
-#define AT91_ST_ALMV (0xfffff << 0) /* Alarm Value */
-#define AT91_ST_CRTR (AT91_ST + 0x24) /* Current Real-time Register */
-#define AT91_ST_CRTV (0xfffff << 0) /* Current Real-Time Value */
-
-
-/*
- * Real-time Clock.
- */
-#define AT91_RTC 0xe00
-
-#define AT91_RTC_CR (AT91_RTC + 0x00) /* Control Register */
-#define AT91_RTC_UPDTIM (1 << 0) /* Update Request Time Register */
-#define AT91_RTC_UPDCAL (1 << 1) /* Update Request Calendar Register */
-#define AT91_RTC_TIMEVSEL (3 << 8) /* Time Event Selection */
-#define AT91_RTC_TIMEVSEL_MINUTE (0 << 8)
-#define AT91_RTC_TIMEVSEL_HOUR (1 << 8)
-#define AT91_RTC_TIMEVSEL_DAY24 (2 << 8)
-#define AT91_RTC_TIMEVSEL_DAY12 (3 << 8)
-#define AT91_RTC_CALEVSEL (3 << 16) /* Calendar Event Selection */
-#define AT91_RTC_CALEVSEL_WEEK (0 << 16)
-#define AT91_RTC_CALEVSEL_MONTH (1 << 16)
-#define AT91_RTC_CALEVSEL_YEAR (2 << 16)
-
-#define AT91_RTC_MR (AT91_RTC + 0x04) /* Mode Register */
-#define AT91_RTC_HRMOD (1 << 0) /* 12/24 Hour Mode */
-
-#define AT91_RTC_TIMR (AT91_RTC + 0x08) /* Time Register */
-#define AT91_RTC_SEC (0x7f << 0) /* Current Second */
-#define AT91_RTC_MIN (0x7f << 8) /* Current Minute */
-#define AT91_RTC_HOUR (0x3f << 16) /* Current Hour */
-#define AT91_RTC_AMPM (1 << 22) /* Ante Meridiem Post Meridiem Indicator */
-
-#define AT91_RTC_CALR (AT91_RTC + 0x0c) /* Calendar Register */
-#define AT91_RTC_CENT (0x7f << 0) /* Current Century */
-#define AT91_RTC_YEAR (0xff << 8) /* Current Year */
-#define AT91_RTC_MONTH (0x1f << 16) /* Current Month */
-#define AT91_RTC_DAY (7 << 21) /* Current Day */
-#define AT91_RTC_DATE (0x3f << 24) /* Current Date */
-
-#define AT91_RTC_TIMALR (AT91_RTC + 0x10) /* Time Alarm Register */
-#define AT91_RTC_SECEN (1 << 7) /* Second Alarm Enable */
-#define AT91_RTC_MINEN (1 << 15) /* Minute Alarm Enable */
-#define AT91_RTC_HOUREN (1 << 23) /* Hour Alarm Enable */
-
-#define AT91_RTC_CALALR (AT91_RTC + 0x14) /* Calendar Alarm Register */
-#define AT91_RTC_MTHEN (1 << 23) /* Month Alarm Enable */
-#define AT91_RTC_DATEEN (1 << 31) /* Date Alarm Enable */
-
-#define AT91_RTC_SR (AT91_RTC + 0x18) /* Status Register */
-#define AT91_RTC_ACKUPD (1 << 0) /* Acknowledge for Update */
-#define AT91_RTC_ALARM (1 << 1) /* Alarm Flag */
-#define AT91_RTC_SECEV (1 << 2) /* Second Event */
-#define AT91_RTC_TIMEV (1 << 3) /* Time Event */
-#define AT91_RTC_CALEV (1 << 4) /* Calendar Event */
-
-#define AT91_RTC_SCCR (AT91_RTC + 0x1c) /* Status Clear Command Register */
-#define AT91_RTC_IER (AT91_RTC + 0x20) /* Interrupt Enable Register */
-#define AT91_RTC_IDR (AT91_RTC + 0x24) /* Interrupt Disable Register */
-#define AT91_RTC_IMR (AT91_RTC + 0x28) /* Interrupt Mask Register */
-
-#define AT91_RTC_VER (AT91_RTC + 0x2c) /* Valid Entry Register */
-#define AT91_RTC_NVTIM (1 << 0) /* Non valid Time */
-#define AT91_RTC_NVCAL (1 << 1) /* Non valid Calendar */
-#define AT91_RTC_NVTIMALR (1 << 2) /* Non valid Time Alarm */
-#define AT91_RTC_NVCALALR (1 << 3) /* Non valid Calendar Alarm */
-
-
-/*
- * Memory Controller.
- */
-#define AT91_MC 0xf00
-
-#define AT91_MC_RCR (AT91_MC + 0x00) /* MC Remap Control Register */
-#define AT91_MC_RCB (1 << 0) /* Remap Command Bit */
-
-#define AT91_MC_ASR (AT91_MC + 0x04) /* MC Abort Status Register */
-#define AT91_MC_UNADD (1 << 0) /* Undefined Address Abort Status */
-#define AT91_MC_MISADD (1 << 1) /* Misaligned Address Abort Status */
-#define AT91_MC_ABTSZ (3 << 8) /* Abort Size Status */
-#define AT91_MC_ABTSZ_BYTE (0 << 8)
-#define AT91_MC_ABTSZ_HALFWORD (1 << 8)
-#define AT91_MC_ABTSZ_WORD (2 << 8)
-#define AT91_MC_ABTTYP (3 << 10) /* Abort Type Status */
-#define AT91_MC_ABTTYP_DATAREAD (0 << 10)
-#define AT91_MC_ABTTYP_DATAWRITE (1 << 10)
-#define AT91_MC_ABTTYP_FETCH (2 << 10)
-#define AT91_MC_MST0 (1 << 16) /* ARM920T Abort Source */
-#define AT91_MC_MST1 (1 << 17) /* PDC Abort Source */
-#define AT91_MC_MST2 (1 << 18) /* UHP Abort Source */
-#define AT91_MC_MST3 (1 << 19) /* EMAC Abort Source */
-#define AT91_MC_SVMST0 (1 << 24) /* Saved ARM920T Abort Source */
-#define AT91_MC_SVMST1 (1 << 25) /* Saved PDC Abort Source */
-#define AT91_MC_SVMST2 (1 << 26) /* Saved UHP Abort Source */
-#define AT91_MC_SVMST3 (1 << 27) /* Saved EMAC Abort Source */
-
-#define AT91_MC_AASR (AT91_MC + 0x08) /* MC Abort Address Status Register */
-
-#define AT91_MC_MPR (AT91_MC + 0x0c) /* MC Master Priority Register */
-#define AT91_MPR_MSTP0 (7 << 0) /* ARM920T Priority */
-#define AT91_MPR_MSTP1 (7 << 4) /* PDC Priority */
-#define AT91_MPR_MSTP2 (7 << 8) /* UHP Priority */
-#define AT91_MPR_MSTP3 (7 << 12) /* EMAC Priority */
-
-/* External Bus Interface (EBI) registers */
-#define AT91_EBI_CSA (AT91_MC + 0x60) /* Chip Select Assignment Register */
-#define AT91_EBI_CS0A (1 << 0) /* Chip Select 0 Assignment */
-#define AT91_EBI_CS0A_SMC (0 << 0)
-#define AT91_EBI_CS0A_BFC (1 << 0)
-#define AT91_EBI_CS1A (1 << 1) /* Chip Select 1 Assignment */
-#define AT91_EBI_CS1A_SMC (0 << 1)
-#define AT91_EBI_CS1A_SDRAMC (1 << 1)
-#define AT91_EBI_CS3A (1 << 3) /* Chip Select 2 Assignment */
-#define AT91_EBI_CS3A_SMC (0 << 3)
-#define AT91_EBI_CS3A_SMC_SMARTMEDIA (1 << 3)
-#define AT91_EBI_CS4A (1 << 4) /* Chip Select 3 Assignment */
-#define AT91_EBI_CS4A_SMC (0 << 4)
-#define AT91_EBI_CS4A_SMC_COMPACTFLASH (1 << 4)
-#define AT91_EBI_CFGR (AT91_MC + 0x64) /* Configuration Register */
-#define AT91_EBI_DBPUC (1 << 0) /* Data Bus Pull-Up Configuration */
-
-/* Static Memory Controller (SMC) registers */
-#define AT91_SMC_CSR(n) (AT91_MC + 0x70 + ((n) * 4))/* SMC Chip Select Register */
-#define AT91_SMC_NWS (0x7f << 0) /* Number of Wait States */
-#define AT91_SMC_NWS_(x) ((x) << 0)
-#define AT91_SMC_WSEN (1 << 7) /* Wait State Enable */
-#define AT91_SMC_TDF (0xf << 8) /* Data Float Time */
-#define AT91_SMC_TDF_(x) ((x) << 8)
-#define AT91_SMC_BAT (1 << 12) /* Byte Access Type */
-#define AT91_SMC_DBW (3 << 13) /* Data Bus Width */
-#define AT91_SMC_DBW_16 (1 << 13)
-#define AT91_SMC_DBW_8 (2 << 13)
-#define AT91_SMC_DPR (1 << 15) /* Data Read Protocol */
-#define AT91_SMC_ACSS (3 << 16) /* Address to Chip Select Setup */
-#define AT91_SMC_ACSS_STD (0 << 16)
-#define AT91_SMC_ACSS_1 (1 << 16)
-#define AT91_SMC_ACSS_2 (2 << 16)
-#define AT91_SMC_ACSS_3 (3 << 16)
-#define AT91_SMC_RWSETUP (7 << 24) /* Read & Write Signal Time Setup */
-#define AT91_SMC_RWSETUP_(x) ((x) << 24)
-#define AT91_SMC_RWHOLD (7 << 28) /* Read & Write Signal Hold Time */
-#define AT91_SMC_RWHOLD_(x) ((x) << 28)
-
-/* SDRAM Controller registers */
-#define AT91_SDRAMC_MR (AT91_MC + 0x90) /* Mode Register */
-#define AT91_SDRAMC_MODE (0xf << 0) /* Command Mode */
-#define AT91_SDRAMC_MODE_NORMAL (0 << 0)
-#define AT91_SDRAMC_MODE_NOP (1 << 0)
-#define AT91_SDRAMC_MODE_PRECHARGE (2 << 0)
-#define AT91_SDRAMC_MODE_LMR (3 << 0)
-#define AT91_SDRAMC_MODE_REFRESH (4 << 0)
-#define AT91_SDRAMC_DBW (1 << 4) /* Data Bus Width */
-#define AT91_SDRAMC_DBW_32 (0 << 4)
-#define AT91_SDRAMC_DBW_16 (1 << 4)
-
-#define AT91_SDRAMC_TR (AT91_MC + 0x94) /* Refresh Timer Register */
-#define AT91_SDRAMC_COUNT (0xfff << 0) /* Refresh Timer Count */
-
-#define AT91_SDRAMC_CR (AT91_MC + 0x98) /* Configuration Register */
-#define AT91_SDRAMC_NC (3 << 0) /* Number of Column Bits */
-#define AT91_SDRAMC_NC_8 (0 << 0)
-#define AT91_SDRAMC_NC_9 (1 << 0)
-#define AT91_SDRAMC_NC_10 (2 << 0)
-#define AT91_SDRAMC_NC_11 (3 << 0)
-#define AT91_SDRAMC_NR (3 << 2) /* Number of Row Bits */
-#define AT91_SDRAMC_NR_11 (0 << 2)
-#define AT91_SDRAMC_NR_12 (1 << 2)
-#define AT91_SDRAMC_NR_13 (2 << 2)
-#define AT91_SDRAMC_NB (1 << 4) /* Number of Banks */
-#define AT91_SDRAMC_NB_2 (0 << 4)
-#define AT91_SDRAMC_NB_4 (1 << 4)
-#define AT91_SDRAMC_CAS (3 << 5) /* CAS Latency */
-#define AT91_SDRAMC_CAS_2 (2 << 5)
-#define AT91_SDRAMC_TWR (0xf << 7) /* Write Recovery Delay */
-#define AT91_SDRAMC_TRC (0xf << 11) /* Row Cycle Delay */
-#define AT91_SDRAMC_TRP (0xf << 15) /* Row Precharge Delay */
-#define AT91_SDRAMC_TRCD (0xf << 19) /* Row to Column Delay */
-#define AT91_SDRAMC_TRAS (0xf << 23) /* Active to Precharge Delay */
-#define AT91_SDRAMC_TXSR (0xf << 27) /* Exit Self Refresh to Active Delay */
-
-#define AT91_SDRAMC_SRR (AT91_MC + 0x9c) /* Self Refresh Register */
-#define AT91_SDRAMC_LPR (AT91_MC + 0xa0) /* Low Power Register */
-#define AT91_SDRAMC_IER (AT91_MC + 0xa4) /* Interrupt Enable Register */
-#define AT91_SDRAMC_IDR (AT91_MC + 0xa8) /* Interrupt Disable Register */
-#define AT91_SDRAMC_IMR (AT91_MC + 0xac) /* Interrupt Mask Register */
-#define AT91_SDRAMC_ISR (AT91_MC + 0xb0) /* Interrupt Status Register */
-
-/* Burst Flash Controller register */
-#define AT91_BFC_MR (AT91_MC + 0xc0) /* Mode Register */
-#define AT91_BFC_BFCOM (3 << 0) /* Burst Flash Controller Operating Mode */
-#define AT91_BFC_BFCOM_DISABLED (0 << 0)
-#define AT91_BFC_BFCOM_ASYNC (1 << 0)
-#define AT91_BFC_BFCOM_BURST (2 << 0)
-#define AT91_BFC_BFCC (3 << 2) /* Burst Flash Controller Clock */
-#define AT91_BFC_BFCC_MCK (1 << 2)
-#define AT91_BFC_BFCC_DIV2 (2 << 2)
-#define AT91_BFC_BFCC_DIV4 (3 << 2)
-#define AT91_BFC_AVL (0xf << 4) /* Address Valid Latency */
-#define AT91_BFC_PAGES (7 << 8) /* Page Size */
-#define AT91_BFC_PAGES_NO_PAGE (0 << 8)
-#define AT91_BFC_PAGES_16 (1 << 8)
-#define AT91_BFC_PAGES_32 (2 << 8)
-#define AT91_BFC_PAGES_64 (3 << 8)
-#define AT91_BFC_PAGES_128 (4 << 8)
-#define AT91_BFC_PAGES_256 (5 << 8)
-#define AT91_BFC_PAGES_512 (6 << 8)
-#define AT91_BFC_PAGES_1024 (7 << 8)
-#define AT91_BFC_OEL (3 << 12) /* Output Enable Latency */
-#define AT91_BFC_BAAEN (1 << 16) /* Burst Address Advance Enable */
-#define AT91_BFC_BFOEH (1 << 17) /* Burst Flash Output Enable Handling */
-#define AT91_BFC_MUXEN (1 << 18) /* Multiplexed Bus Enable */
-#define AT91_BFC_RDYEN (1 << 19) /* Ready Enable Mode */
-
-#endif