USB: g_file_storage: Set sense info Valid bit only when needed
Strictly speaking, the Valid bit in SCSI sense data is supposed to
be set only when the Information field contains a valid number. This
patch (as793) turns off the Valid bit when the Information field
hasn't been set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/drivers/usb/gadget/file_storage.c b/drivers/usb/gadget/file_storage.c
index d472c9c..c83d3b6 100644
--- a/drivers/usb/gadget/file_storage.c
+++ b/drivers/usb/gadget/file_storage.c
@@ -567,6 +567,7 @@
unsigned int ro : 1;
unsigned int prevent_medium_removal : 1;
unsigned int registered : 1;
+ unsigned int info_valid : 1;
u32 sense_data;
u32 sense_data_info;
@@ -1656,6 +1657,7 @@
curlun->sense_data =
SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
curlun->sense_data_info = file_offset >> 9;
+ curlun->info_valid = 1;
bh->inreq->length = 0;
bh->state = BUF_STATE_FULL;
break;
@@ -1691,6 +1693,7 @@
if (nread < amount) {
curlun->sense_data = SS_UNRECOVERED_READ_ERROR;
curlun->sense_data_info = file_offset >> 9;
+ curlun->info_valid = 1;
break;
}
@@ -1785,6 +1788,7 @@
curlun->sense_data =
SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
curlun->sense_data_info = usb_offset >> 9;
+ curlun->info_valid = 1;
continue;
}
amount -= (amount & 511);
@@ -1827,6 +1831,7 @@
if (bh->outreq->status != 0) {
curlun->sense_data = SS_COMMUNICATION_FAILURE;
curlun->sense_data_info = file_offset >> 9;
+ curlun->info_valid = 1;
break;
}
@@ -1868,6 +1873,7 @@
if (nwritten < amount) {
curlun->sense_data = SS_WRITE_ERROR;
curlun->sense_data_info = file_offset >> 9;
+ curlun->info_valid = 1;
break;
}
@@ -2010,6 +2016,7 @@
curlun->sense_data =
SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE;
curlun->sense_data_info = file_offset >> 9;
+ curlun->info_valid = 1;
break;
}
@@ -2036,6 +2043,7 @@
if (nread == 0) {
curlun->sense_data = SS_UNRECOVERED_READ_ERROR;
curlun->sense_data_info = file_offset >> 9;
+ curlun->info_valid = 1;
break;
}
file_offset += nread;
@@ -2079,6 +2087,7 @@
struct lun *curlun = fsg->curlun;
u8 *buf = (u8 *) bh->buf;
u32 sd, sdinfo;
+ int valid;
/*
* From the SCSI-2 spec., section 7.9 (Unit attention condition):
@@ -2106,15 +2115,18 @@
fsg->bad_lun_okay = 1;
sd = SS_LOGICAL_UNIT_NOT_SUPPORTED;
sdinfo = 0;
+ valid = 0;
} else {
sd = curlun->sense_data;
sdinfo = curlun->sense_data_info;
+ valid = curlun->info_valid << 7;
curlun->sense_data = SS_NO_SENSE;
curlun->sense_data_info = 0;
+ curlun->info_valid = 0;
}
memset(buf, 0, 18);
- buf[0] = 0x80 | 0x70; // Valid, current error
+ buf[0] = valid | 0x70; // Valid, current error
buf[2] = SK(sd);
put_be32(&buf[3], sdinfo); // Sense information
buf[7] = 18 - 8; // Additional sense length
@@ -2703,6 +2715,7 @@
if (fsg->cmnd[0] != SC_REQUEST_SENSE) {
curlun->sense_data = SS_NO_SENSE;
curlun->sense_data_info = 0;
+ curlun->info_valid = 0;
}
} else {
fsg->curlun = curlun = NULL;
@@ -3332,6 +3345,7 @@
curlun->sense_data = curlun->unit_attention_data =
SS_NO_SENSE;
curlun->sense_data_info = 0;
+ curlun->info_valid = 0;
}
fsg->state = FSG_STATE_IDLE;
}