drivers/usb/host/ohci-pxa27x.c - kernel/msm - Gitiles

 /*
  * OHCI HCD (Host Controller Driver) for USB.
  *
  * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
  * (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
  * (C) Copyright 2002 Hewlett-Packard Company
  *
  * Bus Glue for pxa27x
  *
  * Written by Christopher Hoover <ch@hpl.hp.com>
  * Based on fragments of previous driver by Russell King et al.
  *
  * Modified for LH7A404 from ohci-sa1111.c
  *  by Durgesh Pattamatta <pattamattad@sharpsec.com>
  *
  * Modified for pxa27x from ohci-lh7a404.c
  *  by Nick Bane <nick@cecomputing.co.uk> 26-8-2004
  *
  * This file is licenced under the GPL.
  */

 #include <linux/device.h>
 #include <linux/signal.h>
 #include <linux/platform_device.h>
 #include <linux/clk.h>

 #include <asm/mach-types.h>
 #include <asm/hardware.h>
 #include <asm/arch/pxa-regs.h>
 #include <asm/arch/ohci.h>

 #define PXA_UHC_MAX_PORTNUM    3

 #define UHCRHPS(x)              __REG2( 0x4C000050, (x)<<2 )

 static struct clk *usb_clk;

 /*
   PMM_NPS_MODE -- PMM Non-power switching mode
       Ports are powered continuously.

   PMM_GLOBAL_MODE -- PMM global switching mode
       All ports are powered at the same time.

   PMM_PERPORT_MODE -- PMM per port switching mode
       Ports are powered individually.
  */
 static int pxa27x_ohci_select_pmm( int mode )
 {
 	switch ( mode ) {
 	case PMM_NPS_MODE:
 		UHCRHDA |= RH_A_NPS;
 		break;
 	case PMM_GLOBAL_MODE:
 		UHCRHDA &= ~(RH_A_NPS & RH_A_PSM);
 		break;
 	case PMM_PERPORT_MODE:
 		UHCRHDA &= ~(RH_A_NPS);
 		UHCRHDA |= RH_A_PSM;

 		/* Set port power control mask bits, only 3 ports. */
 		UHCRHDB |= (0x7<<17);
 		break;
 	default:
 		printk( KERN_ERR
 			"Invalid mode %d, set to non-power switch mode.\n",
 			mode );

 		UHCRHDA |= RH_A_NPS;
 	}

 	return 0;
 }

 extern int usb_disabled(void);

 /*-------------------------------------------------------------------------*/

 static int pxa27x_start_hc(struct device *dev)
 {
 	int retval = 0;
 	struct pxaohci_platform_data *inf;

 	inf = dev->platform_data;

 	clk_enable(usb_clk);

 	UHCHR |= UHCHR_FHR;
 	udelay(11);
 	UHCHR &= ~UHCHR_FHR;

 	UHCHR |= UHCHR_FSBIR;
 	while (UHCHR & UHCHR_FSBIR)
 		cpu_relax();

 	if (inf->init)
 		retval = inf->init(dev);

 	if (retval < 0)
 		return retval;

 	UHCHR &= ~UHCHR_SSE;

 	UHCHIE = (UHCHIE_UPRIE | UHCHIE_RWIE);

 	/* Clear any OTG Pin Hold */
 	if (PSSR & PSSR_OTGPH)
 		PSSR |= PSSR_OTGPH;

 	return 0;
 }

 static void pxa27x_stop_hc(struct device *dev)
 {
 	struct pxaohci_platform_data *inf;

 	inf = dev->platform_data;

 	if (inf->exit)
 		inf->exit(dev);

 	UHCHR |= UHCHR_FHR;
 	udelay(11);
 	UHCHR &= ~UHCHR_FHR;

 	UHCCOMS |= 1;
 	udelay(10);

 	clk_disable(usb_clk);
 }


 /*-------------------------------------------------------------------------*/

 /* configure so an HC device and id are always provided */
 /* always called with process context; sleeping is OK */


 /**
  * usb_hcd_pxa27x_probe - initialize pxa27x-based HCDs
  * Context: !in_interrupt()
  *
  * Allocates basic resources for this USB host controller, and
  * then invokes the start() method for the HCD associated with it
  * through the hotplug entry's driver_data.
  *
  */
 int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device *pdev)
 {
 	int retval;
 	struct usb_hcd *hcd;
 	struct pxaohci_platform_data *inf;

 	inf = pdev->dev.platform_data;

 	if (!inf)
 		return -ENODEV;

 	if (pdev->resource[1].flags != IORESOURCE_IRQ) {
 		pr_debug ("resource[1] is not IORESOURCE_IRQ");
 		return -ENOMEM;
 	}

 	usb_clk = clk_get(&pdev->dev, "USBCLK");
 	if (IS_ERR(usb_clk))
 		return PTR_ERR(usb_clk);

 	hcd = usb_create_hcd (driver, &pdev->dev, "pxa27x");
 	if (!hcd)
 		return -ENOMEM;
 	hcd->rsrc_start = pdev->resource[0].start;
 	hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;

 	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
 		pr_debug("request_mem_region failed");
 		retval = -EBUSY;
 		goto err1;
 	}

 	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
 	if (!hcd->regs) {
 		pr_debug("ioremap failed");
 		retval = -ENOMEM;
 		goto err2;
 	}

 	if ((retval = pxa27x_start_hc(&pdev->dev)) < 0) {
 		pr_debug("pxa27x_start_hc failed");
 		goto err3;
 	}

 	/* Select Power Management Mode */
 	pxa27x_ohci_select_pmm(inf->port_mode);

 	if (inf->power_budget)
 		hcd->power_budget = inf->power_budget;

 	ohci_hcd_init(hcd_to_ohci(hcd));

 	retval = usb_add_hcd(hcd, pdev->resource[1].start, IRQF_DISABLED);
 	if (retval == 0)
 		return retval;

 	pxa27x_stop_hc(&pdev->dev);
  err3:
 	iounmap(hcd->regs);
  err2:
 	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
  err1:
 	usb_put_hcd(hcd);
 	clk_put(usb_clk);
 	return retval;
 }


 /* may be called without controller electrically present */
 /* may be called with controller, bus, and devices active */

 /**
  * usb_hcd_pxa27x_remove - shutdown processing for pxa27x-based HCDs
  * @dev: USB Host Controller being removed
  * Context: !in_interrupt()
  *
  * Reverses the effect of usb_hcd_pxa27x_probe(), first invoking
  * the HCD's stop() method.  It is always called from a thread
  * context, normally "rmmod", "apmd", or something similar.
  *
  */
 void usb_hcd_pxa27x_remove (struct usb_hcd *hcd, struct platform_device *pdev)
 {
 	usb_remove_hcd(hcd);
 	pxa27x_stop_hc(&pdev->dev);
 	iounmap(hcd->regs);
 	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
 	usb_put_hcd(hcd);
 	clk_put(usb_clk);
 }

 /*-------------------------------------------------------------------------*/

 static int __devinit
 ohci_pxa27x_start (struct usb_hcd *hcd)
 {
 	struct ohci_hcd	*ohci = hcd_to_ohci (hcd);
 	int		ret;

 	ohci_dbg (ohci, "ohci_pxa27x_start, ohci:%p", ohci);

 	/* The value of NDP in roothub_a is incorrect on this hardware */
 	ohci->num_ports = 3;

 	if ((ret = ohci_init(ohci)) < 0)
 		return ret;

 	if ((ret = ohci_run (ohci)) < 0) {
 		err ("can't start %s", hcd->self.bus_name);
 		ohci_stop (hcd);
 		return ret;
 	}

 	return 0;
 }

 /*-------------------------------------------------------------------------*/

 static const struct hc_driver ohci_pxa27x_hc_driver = {
 	.description =		hcd_name,
 	.product_desc =		"PXA27x OHCI",
 	.hcd_priv_size =	sizeof(struct ohci_hcd),

 	/*
 	 * generic hardware linkage
 	 */
 	.irq =			ohci_irq,
 	.flags =		HCD_USB11 | HCD_MEMORY,

 	/*
 	 * basic lifecycle operations
 	 */
 	.start =		ohci_pxa27x_start,
 	.stop =			ohci_stop,
 	.shutdown =		ohci_shutdown,

 	/*
 	 * managing i/o requests and associated device resources
 	 */
 	.urb_enqueue =		ohci_urb_enqueue,
 	.urb_dequeue =		ohci_urb_dequeue,
 	.endpoint_disable =	ohci_endpoint_disable,

 	/*
 	 * scheduling support
 	 */
 	.get_frame_number =	ohci_get_frame,

 	/*
 	 * root hub support
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
 	.hub_irq_enable =	ohci_rhsc_enable,
 #ifdef  CONFIG_PM
 	.bus_suspend =		ohci_bus_suspend,
 	.bus_resume =		ohci_bus_resume,
 #endif
 	.start_port_reset =	ohci_start_port_reset,
 };

 /*-------------------------------------------------------------------------*/

 static int ohci_hcd_pxa27x_drv_probe(struct platform_device *pdev)
 {
 	pr_debug ("In ohci_hcd_pxa27x_drv_probe");

 	if (usb_disabled())
 		return -ENODEV;

 	return usb_hcd_pxa27x_probe(&ohci_pxa27x_hc_driver, pdev);
 }

 static int ohci_hcd_pxa27x_drv_remove(struct platform_device *pdev)
 {
 	struct usb_hcd *hcd = platform_get_drvdata(pdev);

 	usb_hcd_pxa27x_remove(hcd, pdev);
 	platform_set_drvdata(pdev, NULL);
 	return 0;
 }

 #ifdef	CONFIG_PM
 static int ohci_hcd_pxa27x_drv_suspend(struct platform_device *pdev, pm_message_t state)
 {
 	struct usb_hcd *hcd = platform_get_drvdata(pdev);
 	struct ohci_hcd *ohci = hcd_to_ohci(hcd);

 	if (time_before(jiffies, ohci->next_statechange))
 		msleep(5);
 	ohci->next_statechange = jiffies;

 	pxa27x_stop_hc(&pdev->dev);
 	hcd->state = HC_STATE_SUSPENDED;

 	return 0;
 }

 static int ohci_hcd_pxa27x_drv_resume(struct platform_device *pdev)
 {
 	struct usb_hcd *hcd = platform_get_drvdata(pdev);
 	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
 	int status;

 	if (time_before(jiffies, ohci->next_statechange))
 		msleep(5);
 	ohci->next_statechange = jiffies;

 	if ((status = pxa27x_start_hc(&pdev->dev)) < 0)
 		return status;

 	ohci_finish_controller_resume(hcd);
 	return 0;
 }
 #endif

 /* work with hotplug and coldplug */
 MODULE_ALIAS("platform:pxa27x-ohci");

 static struct platform_driver ohci_hcd_pxa27x_driver = {
 	.probe		= ohci_hcd_pxa27x_drv_probe,
 	.remove		= ohci_hcd_pxa27x_drv_remove,
 	.shutdown	= usb_hcd_platform_shutdown,
 #ifdef CONFIG_PM
 	.suspend	= ohci_hcd_pxa27x_drv_suspend,
 	.resume		= ohci_hcd_pxa27x_drv_resume,
 #endif
 	.driver		= {
 		.name	= "pxa27x-ohci",
 		.owner	= THIS_MODULE,
 	},
 };
	/*
	* OHCI HCD (Host Controller Driver) for USB.
	*
	* (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
	* (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
	* (C) Copyright 2002 Hewlett-Packard Company
	*
	* Bus Glue for pxa27x
	*
	* Written by Christopher Hoover <ch@hpl.hp.com>
	* Based on fragments of previous driver by Russell King et al.
	*
	* Modified for LH7A404 from ohci-sa1111.c
	* by Durgesh Pattamatta <pattamattad@sharpsec.com>
	*
	* Modified for pxa27x from ohci-lh7a404.c
	* by Nick Bane <nick@cecomputing.co.uk> 26-8-2004
	*
	* This file is licenced under the GPL.
	*/

	#include <linux/device.h>
	#include <linux/signal.h>
	#include <linux/platform_device.h>
	#include <linux/clk.h>

	#include <asm/mach-types.h>
	#include <asm/hardware.h>
	#include <asm/arch/pxa-regs.h>
	#include <asm/arch/ohci.h>

	#define PXA_UHC_MAX_PORTNUM 3

	#define UHCRHPS(x) __REG2( 0x4C000050, (x)<<2 )

	static struct clk *usb_clk;

	/*
	PMM_NPS_MODE -- PMM Non-power switching mode
	Ports are powered continuously.

	PMM_GLOBAL_MODE -- PMM global switching mode
	All ports are powered at the same time.

	PMM_PERPORT_MODE -- PMM per port switching mode
	Ports are powered individually.
	*/
	static int pxa27x_ohci_select_pmm( int mode )
	{
	switch ( mode ) {
	case PMM_NPS_MODE:
	UHCRHDA \|= RH_A_NPS;
	break;
	case PMM_GLOBAL_MODE:
	UHCRHDA &= ~(RH_A_NPS & RH_A_PSM);
	break;
	case PMM_PERPORT_MODE:
	UHCRHDA &= ~(RH_A_NPS);
	UHCRHDA \|= RH_A_PSM;

	/* Set port power control mask bits, only 3 ports. */
	UHCRHDB \|= (0x7<<17);
	break;
	default:
	printk( KERN_ERR
	"Invalid mode %d, set to non-power switch mode.\n",
	mode );

	UHCRHDA \|= RH_A_NPS;
	}

	return 0;
	}

	extern int usb_disabled(void);

	/-------------------------------------------------------------------------/

	static int pxa27x_start_hc(struct device *dev)
	{
	int retval = 0;
	struct pxaohci_platform_data *inf;

	inf = dev->platform_data;

	clk_enable(usb_clk);

	UHCHR \|= UHCHR_FHR;
	udelay(11);
	UHCHR &= ~UHCHR_FHR;

	UHCHR \|= UHCHR_FSBIR;
	while (UHCHR & UHCHR_FSBIR)
	cpu_relax();

	if (inf->init)
	retval = inf->init(dev);

	if (retval < 0)
	return retval;

	UHCHR &= ~UHCHR_SSE;

	UHCHIE = (UHCHIE_UPRIE \| UHCHIE_RWIE);

	/* Clear any OTG Pin Hold */
	if (PSSR & PSSR_OTGPH)
	PSSR \|= PSSR_OTGPH;

	return 0;
	}

	static void pxa27x_stop_hc(struct device *dev)
	{
	struct pxaohci_platform_data *inf;

	inf = dev->platform_data;

	if (inf->exit)
	inf->exit(dev);

	UHCHR \|= UHCHR_FHR;
	udelay(11);
	UHCHR &= ~UHCHR_FHR;

	UHCCOMS \|= 1;
	udelay(10);

	clk_disable(usb_clk);
	}


	/-------------------------------------------------------------------------/

	/* configure so an HC device and id are always provided */
	/* always called with process context; sleeping is OK */


	/**
	* usb_hcd_pxa27x_probe - initialize pxa27x-based HCDs
	* Context: !in_interrupt()
	*
	* Allocates basic resources for this USB host controller, and
	* then invokes the start() method for the HCD associated with it
	* through the hotplug entry's driver_data.
	*
	*/
	int usb_hcd_pxa27x_probe (const struct hc_driver driver, struct platform_device pdev)
	{
	int retval;
	struct usb_hcd *hcd;
	struct pxaohci_platform_data *inf;

	inf = pdev->dev.platform_data;

	if (!inf)
	return -ENODEV;

	if (pdev->resource[1].flags != IORESOURCE_IRQ) {
	pr_debug ("resource[1] is not IORESOURCE_IRQ");
	return -ENOMEM;
	}

	usb_clk = clk_get(&pdev->dev, "USBCLK");
	if (IS_ERR(usb_clk))
	return PTR_ERR(usb_clk);

	hcd = usb_create_hcd (driver, &pdev->dev, "pxa27x");
	if (!hcd)
	return -ENOMEM;
	hcd->rsrc_start = pdev->resource[0].start;
	hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;

	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
	pr_debug("request_mem_region failed");
	retval = -EBUSY;
	goto err1;
	}

	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
	if (!hcd->regs) {
	pr_debug("ioremap failed");
	retval = -ENOMEM;
	goto err2;
	}

	if ((retval = pxa27x_start_hc(&pdev->dev)) < 0) {
	pr_debug("pxa27x_start_hc failed");
	goto err3;
	}

	/* Select Power Management Mode */
	pxa27x_ohci_select_pmm(inf->port_mode);

	if (inf->power_budget)
	hcd->power_budget = inf->power_budget;

	ohci_hcd_init(hcd_to_ohci(hcd));

	retval = usb_add_hcd(hcd, pdev->resource[1].start, IRQF_DISABLED);
	if (retval == 0)
	return retval;

	pxa27x_stop_hc(&pdev->dev);
	err3:
	iounmap(hcd->regs);
	err2:
	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
	err1:
	usb_put_hcd(hcd);
	clk_put(usb_clk);
	return retval;
	}


	/* may be called without controller electrically present */
	/* may be called with controller, bus, and devices active */

	/**
	* usb_hcd_pxa27x_remove - shutdown processing for pxa27x-based HCDs
	* @dev: USB Host Controller being removed
	* Context: !in_interrupt()
	*
	* Reverses the effect of usb_hcd_pxa27x_probe(), first invoking
	* the HCD's stop() method. It is always called from a thread
	* context, normally "rmmod", "apmd", or something similar.
	*
	*/
	void usb_hcd_pxa27x_remove (struct usb_hcd hcd, struct platform_device pdev)
	{
	usb_remove_hcd(hcd);
	pxa27x_stop_hc(&pdev->dev);
	iounmap(hcd->regs);
	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
	usb_put_hcd(hcd);
	clk_put(usb_clk);
	}

	/-------------------------------------------------------------------------/

	static int __devinit
	ohci_pxa27x_start (struct usb_hcd *hcd)
	{
	struct ohci_hcd *ohci = hcd_to_ohci (hcd);
	int ret;

	ohci_dbg (ohci, "ohci_pxa27x_start, ohci:%p", ohci);

	/* The value of NDP in roothub_a is incorrect on this hardware */
	ohci->num_ports = 3;

	if ((ret = ohci_init(ohci)) < 0)
	return ret;

	if ((ret = ohci_run (ohci)) < 0) {
	err ("can't start %s", hcd->self.bus_name);
	ohci_stop (hcd);
	return ret;
	}

	return 0;
	}

	/-------------------------------------------------------------------------/

	static const struct hc_driver ohci_pxa27x_hc_driver = {
	.description = hcd_name,
	.product_desc = "PXA27x OHCI",
	.hcd_priv_size = sizeof(struct ohci_hcd),

	/*
	* generic hardware linkage
	*/
	.irq = ohci_irq,
	.flags = HCD_USB11 \| HCD_MEMORY,

	/*
	* basic lifecycle operations
	*/
	.start = ohci_pxa27x_start,
	.stop = ohci_stop,
	.shutdown = ohci_shutdown,

	/*
	* managing i/o requests and associated device resources
	*/
	.urb_enqueue = ohci_urb_enqueue,
	.urb_dequeue = ohci_urb_dequeue,
	.endpoint_disable = ohci_endpoint_disable,

	/*
	* scheduling support
	*/
	.get_frame_number = ohci_get_frame,

	/*
	* root hub support
	*/
	.hub_status_data = ohci_hub_status_data,
	.hub_control = ohci_hub_control,
	.hub_irq_enable = ohci_rhsc_enable,
	#ifdef CONFIG_PM
	.bus_suspend = ohci_bus_suspend,
	.bus_resume = ohci_bus_resume,
	#endif
	.start_port_reset = ohci_start_port_reset,
	};

	/-------------------------------------------------------------------------/

	static int ohci_hcd_pxa27x_drv_probe(struct platform_device *pdev)
	{
	pr_debug ("In ohci_hcd_pxa27x_drv_probe");

	if (usb_disabled())
	return -ENODEV;

	return usb_hcd_pxa27x_probe(&ohci_pxa27x_hc_driver, pdev);
	}

	static int ohci_hcd_pxa27x_drv_remove(struct platform_device *pdev)
	{
	struct usb_hcd *hcd = platform_get_drvdata(pdev);

	usb_hcd_pxa27x_remove(hcd, pdev);
	platform_set_drvdata(pdev, NULL);
	return 0;
	}

	#ifdef CONFIG_PM
	static int ohci_hcd_pxa27x_drv_suspend(struct platform_device *pdev, pm_message_t state)
	{
	struct usb_hcd *hcd = platform_get_drvdata(pdev);
	struct ohci_hcd *ohci = hcd_to_ohci(hcd);

	if (time_before(jiffies, ohci->next_statechange))
	msleep(5);
	ohci->next_statechange = jiffies;

	pxa27x_stop_hc(&pdev->dev);
	hcd->state = HC_STATE_SUSPENDED;

	return 0;
	}

	static int ohci_hcd_pxa27x_drv_resume(struct platform_device *pdev)
	{
	struct usb_hcd *hcd = platform_get_drvdata(pdev);
	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
	int status;

	if (time_before(jiffies, ohci->next_statechange))
	msleep(5);
	ohci->next_statechange = jiffies;

	if ((status = pxa27x_start_hc(&pdev->dev)) < 0)
	return status;

	ohci_finish_controller_resume(hcd);
	return 0;
	}
	#endif

	/* work with hotplug and coldplug */
	MODULE_ALIAS("platform:pxa27x-ohci");

	static struct platform_driver ohci_hcd_pxa27x_driver = {
	.probe = ohci_hcd_pxa27x_drv_probe,
	.remove = ohci_hcd_pxa27x_drv_remove,
	.shutdown = usb_hcd_platform_shutdown,
	#ifdef CONFIG_PM
	.suspend = ohci_hcd_pxa27x_drv_suspend,
	.resume = ohci_hcd_pxa27x_drv_resume,
	#endif
	.driver = {
	.name = "pxa27x-ohci",
	.owner = THIS_MODULE,
	},
	};