ide/Kconfig: couple of fixes
* Don't ask to enable no longer existing config options
("Use DMA by default when available" and "Special UDMA Feature").
* PIIX host driver doesn't support Victory66 chipset.
* "ide0=cmd640_vlb" -> "cmd640.probe_vlb"
* "ide=doubler" -> "gayle.doubler"
* Amiga IDE doubler support is a feature for gayle host driver
not a separate host driver.
* Remove Andre's mail.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 627f08e..b4f3aef 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -1,8 +1,6 @@
#
# IDE ATA ATAPI Block device driver configuration
#
-# Andre Hedrick <andre@linux-ide.org>
-#
# Select HAVE_IDE if IDE is supported
config HAVE_IDE
@@ -335,7 +333,7 @@
This driver will work automatically in PCI based systems (most new
systems have PCI slots). But if your system uses VESA local bus
(VLB) instead of PCI, you must also supply a kernel boot parameter
- to enable the CMD640 bugfix/support: "ide0=cmd640_vlb". (Try "man
+ to enable the CMD640 bugfix/support: "cmd640.probe_vlb". (Try "man
bootparam" or see the documentation of your boot loader about how to
pass options to the kernel.)
@@ -457,8 +455,7 @@
onboard chipsets. It also tests for Simplex mode and enables
normal dual channel support.
- If you say Y here, you also need to say Y to "Use DMA by default
- when available", above. Please read the comments at the top of
+ Please read the comments at the top of
<file:drivers/ide/pci/alim15x3.c>.
If unsure, say N.
@@ -505,9 +502,6 @@
This driver adds detection and support for the CY82C693 chipset
used on Digital's PC-Alpha 164SX boards.
- If you say Y here, you need to say Y to "Use DMA by default
- when available" as well.
-
config BLK_DEV_CS5520
tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)"
depends on EXPERIMENTAL
@@ -598,13 +592,12 @@
National SCx200 series of embedded x86 "Geode" systems.
config BLK_DEV_PIIX
- tristate "Intel PIIXn chipsets support"
+ tristate "Intel PIIX/ICH chipsets support"
select BLK_DEV_IDEDMA_PCI
help
- This driver adds explicit support for Intel PIIX and ICH chips
- and also for the Efar Victory66 (slc90e66) chip. This allows
- the kernel to change PIO, DMA and UDMA speeds and to configure
- the chip to optimum performance.
+ This driver adds explicit support for Intel PIIX and ICH chips.
+ This allows the kernel to change PIO, DMA and UDMA speeds and to
+ configure the chip to optimum performance.
config BLK_DEV_IT8213
tristate "IT8213 IDE support"
@@ -642,11 +635,7 @@
happen if the BIOS revisions of all installed cards (three-max) do
not match, the driver attempts to do dynamic tuning of the chipset
at boot-time for max-speed. Ultra33 BIOS 1.25 or newer is required
- for more than one card. This card may require that you say Y to
- "Special UDMA Feature".
-
- If you say Y here, you need to say Y to "Use DMA by default when
- available" as well.
+ for more than one card.
Please read the comments at the top of
<file:drivers/ide/pci/pdc202xx_old.c>.
@@ -695,9 +684,6 @@
ATA100: SiS635, SiS645, SiS650, SiS730, SiS735, SiS740,
SiS745, SiS750
- If you say Y here, you need to say Y to "Use DMA by default when
- available" as well.
-
Please read the comments at the top of <file:drivers/ide/pci/sis5513.c>.
config BLK_DEV_SL82C105
@@ -719,9 +705,6 @@
and it will handle timing cycles. Since this is an improved
look-a-like to the PIIX4 it should be a nice addition.
- If you say Y here, you need to say Y to "Use DMA by default when
- available" as well.
-
Please read the comments at the top of
<file:drivers/ide/pci/slc90e66.c>.
@@ -873,17 +856,17 @@
bool "Amiga IDE Doubler support (EXPERIMENTAL)"
depends on BLK_DEV_GAYLE && EXPERIMENTAL
---help---
- This driver provides support for the so-called `IDE doublers' (made
+ This feature provides support for the so-called `IDE doublers' (made
by various manufacturers, e.g. Eyetech) that can be connected to
the on-board IDE interface of some Amiga models. Using such an IDE
doubler, you can connect up to four instead of two IDE devices to
the Amiga's on-board IDE interface.
Note that the normal Amiga Gayle IDE driver may not work correctly
- if you have an IDE doubler and don't enable this driver!
+ if you have an IDE doubler and don't enable this feature!
- Say Y if you have an IDE doubler. The driver is enabled at kernel
- runtime using the "ide=doubler" kernel boot parameter.
+ Say Y if you have an IDE doubler. The feature is enabled at kernel
+ runtime using the "gayle.doubler" kernel boot parameter.
config BLK_DEV_BUDDHA
tristate "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"