usb: gadget: storage: make FSG_NUM_BUFFERS variable size
FSG_NUM_BUFFERS is set to 2 as default.
Usually 2 buffers are enough to establish a good buffering pipeline.
The number may be increased in order to compensate a for bursty VFS
behaviour.
Here follows a description of system that may require more than
2 buffers.
* CPU ondemand governor active
* latency cost for wake up and/or frequency change
* DMA for IO
Use case description.
* Data transfer from MMC via VFS to USB.
* DMA shuffles data from MMC and to USB.
* The CPU wakes up every now and then to pass data in and out from VFS,
which cause the bursty VFS behaviour.
Test set up
* Running dd on the host reading from the mass storage device
* cmdline: dd if=/dev/sdb of=/dev/null bs=4k count=$((256*100))
* Caches are dropped on the host and on the device before each run
Measurements on a Snowball board with ondemand_governor active.
FSG_NUM_BUFFERS 2
104857600 bytes (105 MB) copied, 5.62173 s, 18.7 MB/s
104857600 bytes (105 MB) copied, 5.61811 s, 18.7 MB/s
104857600 bytes (105 MB) copied, 5.57817 s, 18.8 MB/s
FSG_NUM_BUFFERS 4
104857600 bytes (105 MB) copied, 5.26839 s, 19.9 MB/s
104857600 bytes (105 MB) copied, 5.2691 s, 19.9 MB/s
104857600 bytes (105 MB) copied, 5.2711 s, 19.9 MB/s
There may not be one optimal number for all boards. This is why
the number is added to Kconfig. If selecting USB_GADGET_DEBUG_FILES
this value may be set by a module parameter as well.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
diff --git a/drivers/usb/gadget/storage_common.c b/drivers/usb/gadget/storage_common.c
index 3ea70d8..9fd3799 100644
--- a/drivers/usb/gadget/storage_common.c
+++ b/drivers/usb/gadget/storage_common.c
@@ -52,6 +52,12 @@
* characters rather then a pointer to void.
*/
+/*
+ * When USB_GADGET_DEBUG_FILES is defined the module param num_buffers
+ * sets the number of pipeline buffers (length of the fsg_buffhd array).
+ * The valid range of num_buffers is: num >= 2 && num <= 4.
+ */
+
#include <linux/usb/storage.h>
#include <scsi/scsi.h>
@@ -264,8 +270,31 @@
#define EP0_BUFSIZE 256
#define DELAYED_STATUS (EP0_BUFSIZE + 999) /* An impossibly large value */
-/* Number of buffers we will use. 2 is enough for double-buffering */
-#define FSG_NUM_BUFFERS 2
+#ifdef CONFIG_USB_GADGET_DEBUG_FILES
+
+static unsigned int fsg_num_buffers = CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS;
+module_param_named(num_buffers, fsg_num_buffers, uint, S_IRUGO);
+MODULE_PARM_DESC(num_buffers, "Number of pipeline buffers");
+
+#else
+
+/*
+ * Number of buffers we will use.
+ * 2 is usually enough for good buffering pipeline
+ */
+#define fsg_num_buffers CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS
+
+#endif /* CONFIG_USB_DEBUG */
+
+/* check if fsg_num_buffers is within a valid range */
+static inline int fsg_num_buffers_validate(void)
+{
+ if (fsg_num_buffers >= 2 && fsg_num_buffers <= 4)
+ return 0;
+ pr_err("fsg_num_buffers %u is out of range (%d to %d)\n",
+ fsg_num_buffers, 2 ,4);
+ return -EINVAL;
+}
/* Default size of buffer length. */
#define FSG_BUFLEN ((u32)16384)