diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
index fe56379..a60b472 100644
--- a/drivers/usb/gadget/Kconfig
+++ b/drivers/usb/gadget/Kconfig
@@ -96,6 +96,22 @@
 	   This value will be used except for system-specific gadget
 	   drivers that have more specific information.
 
+config USB_GADGET_STORAGE_NUM_BUFFERS
+	int "Number of storage pipeline buffers"
+	range 2 4
+	default 2
+	help
+	   Usually 2 buffers are enough to establish a good buffering
+	   pipeline. The number may be increased in order to compensate
+	   for a bursty VFS behaviour. For instance there may be CPU wake up
+	   latencies that makes the VFS to appear bursty in a system with
+	   an CPU on-demand governor. Especially if DMA is doing IO to
+	   offload the CPU. In this case the CPU will go into power
+	   save often and spin up occasionally to move data within VFS.
+	   If selecting USB_GADGET_DEBUG_FILES this value may be set by
+	   a module parameter as well.
+	   If unsure, say 2.
+
 #
 # USB Peripheral Controller Support
 #
diff --git a/drivers/usb/gadget/f_mass_storage.c b/drivers/usb/gadget/f_mass_storage.c
index 4306a83..7569414 100644
--- a/drivers/usb/gadget/f_mass_storage.c
+++ b/drivers/usb/gadget/f_mass_storage.c
@@ -362,7 +362,7 @@
 
 	struct fsg_buffhd	*next_buffhd_to_fill;
 	struct fsg_buffhd	*next_buffhd_to_drain;
-	struct fsg_buffhd	buffhds[FSG_NUM_BUFFERS];
+	struct fsg_buffhd	*buffhds;
 
 	int			cmnd_size;
 	u8			cmnd[MAX_COMMAND_SIZE];
@@ -2340,7 +2340,7 @@
 	if (common->fsg) {
 		fsg = common->fsg;
 
-		for (i = 0; i < FSG_NUM_BUFFERS; ++i) {
+		for (i = 0; i < fsg_num_buffers; ++i) {
 			struct fsg_buffhd *bh = &common->buffhds[i];
 
 			if (bh->inreq) {
@@ -2397,7 +2397,7 @@
 	clear_bit(IGNORE_BULK_OUT, &fsg->atomic_bitflags);
 
 	/* Allocate the requests */
-	for (i = 0; i < FSG_NUM_BUFFERS; ++i) {
+	for (i = 0; i < fsg_num_buffers; ++i) {
 		struct fsg_buffhd	*bh = &common->buffhds[i];
 
 		rc = alloc_request(common, fsg->bulk_in, &bh->inreq);
@@ -2466,7 +2466,7 @@
 
 	/* Cancel all the pending transfers */
 	if (likely(common->fsg)) {
-		for (i = 0; i < FSG_NUM_BUFFERS; ++i) {
+		for (i = 0; i < fsg_num_buffers; ++i) {
 			bh = &common->buffhds[i];
 			if (bh->inreq_busy)
 				usb_ep_dequeue(common->fsg->bulk_in, bh->inreq);
@@ -2478,7 +2478,7 @@
 		/* Wait until everything is idle */
 		for (;;) {
 			int num_active = 0;
-			for (i = 0; i < FSG_NUM_BUFFERS; ++i) {
+			for (i = 0; i < fsg_num_buffers; ++i) {
 				bh = &common->buffhds[i];
 				num_active += bh->inreq_busy + bh->outreq_busy;
 			}
@@ -2501,7 +2501,7 @@
 	 */
 	spin_lock_irq(&common->lock);
 
-	for (i = 0; i < FSG_NUM_BUFFERS; ++i) {
+	for (i = 0; i < fsg_num_buffers; ++i) {
 		bh = &common->buffhds[i];
 		bh->state = BUF_STATE_EMPTY;
 	}
@@ -2710,6 +2710,10 @@
 	int nluns, i, rc;
 	char *pathbuf;
 
+	rc = fsg_num_buffers_validate();
+	if (rc != 0)
+		return ERR_PTR(rc);
+
 	/* Find out how many LUNs there should be */
 	nluns = cfg->nluns;
 	if (nluns < 1 || nluns > FSG_MAX_LUNS) {
@@ -2728,6 +2732,14 @@
 		common->free_storage_on_release = 0;
 	}
 
+	common->buffhds = kcalloc(fsg_num_buffers,
+				  sizeof *(common->buffhds), GFP_KERNEL);
+	if (!common->buffhds) {
+		if (common->free_storage_on_release)
+			kfree(common);
+		return ERR_PTR(-ENOMEM);
+	}
+
 	common->ops = cfg->ops;
 	common->private_data = cfg->private_data;
 
@@ -2805,7 +2817,7 @@
 
 	/* Data buffers cyclic list */
 	bh = common->buffhds;
-	i = FSG_NUM_BUFFERS;
+	i = fsg_num_buffers;
 	goto buffhds_first_it;
 	do {
 		bh->next = bh + 1;
@@ -2931,12 +2943,13 @@
 
 	{
 		struct fsg_buffhd *bh = common->buffhds;
-		unsigned i = FSG_NUM_BUFFERS;
+		unsigned i = fsg_num_buffers;
 		do {
 			kfree(bh->buf);
 		} while (++bh, --i);
 	}
 
+	kfree(common->buffhds);
 	if (common->free_storage_on_release)
 		kfree(common);
 }
diff --git a/drivers/usb/gadget/file_storage.c b/drivers/usb/gadget/file_storage.c
index c6f96a2..4b9797d 100644
--- a/drivers/usb/gadget/file_storage.c
+++ b/drivers/usb/gadget/file_storage.c
@@ -460,7 +460,6 @@
 
 	struct fsg_buffhd	*next_buffhd_to_fill;
 	struct fsg_buffhd	*next_buffhd_to_drain;
-	struct fsg_buffhd	buffhds[FSG_NUM_BUFFERS];
 
 	int			thread_wakeup_needed;
 	struct completion	thread_notifier;
@@ -487,6 +486,8 @@
 	unsigned int		nluns;
 	struct fsg_lun		*luns;
 	struct fsg_lun		*curlun;
+	/* Must be the last entry */
+	struct fsg_buffhd	buffhds[];
 };
 
 typedef void (*fsg_routine_t)(struct fsg_dev *);
@@ -2737,7 +2738,7 @@
 
 reset:
 	/* Deallocate the requests */
-	for (i = 0; i < FSG_NUM_BUFFERS; ++i) {
+	for (i = 0; i < fsg_num_buffers; ++i) {
 		struct fsg_buffhd *bh = &fsg->buffhds[i];
 
 		if (bh->inreq) {
@@ -2798,7 +2799,7 @@
 	}
 
 	/* Allocate the requests */
-	for (i = 0; i < FSG_NUM_BUFFERS; ++i) {
+	for (i = 0; i < fsg_num_buffers; ++i) {
 		struct fsg_buffhd	*bh = &fsg->buffhds[i];
 
 		if ((rc = alloc_request(fsg, fsg->bulk_in, &bh->inreq)) != 0)
@@ -2894,7 +2895,7 @@
 	/* Cancel all the pending transfers */
 	if (fsg->intreq_busy)
 		usb_ep_dequeue(fsg->intr_in, fsg->intreq);
-	for (i = 0; i < FSG_NUM_BUFFERS; ++i) {
+	for (i = 0; i < fsg_num_buffers; ++i) {
 		bh = &fsg->buffhds[i];
 		if (bh->inreq_busy)
 			usb_ep_dequeue(fsg->bulk_in, bh->inreq);
@@ -2905,7 +2906,7 @@
 	/* Wait until everything is idle */
 	for (;;) {
 		num_active = fsg->intreq_busy;
-		for (i = 0; i < FSG_NUM_BUFFERS; ++i) {
+		for (i = 0; i < fsg_num_buffers; ++i) {
 			bh = &fsg->buffhds[i];
 			num_active += bh->inreq_busy + bh->outreq_busy;
 		}
@@ -2927,7 +2928,7 @@
 	 * state, and the exception.  Then invoke the handler. */
 	spin_lock_irq(&fsg->lock);
 
-	for (i = 0; i < FSG_NUM_BUFFERS; ++i) {
+	for (i = 0; i < fsg_num_buffers; ++i) {
 		bh = &fsg->buffhds[i];
 		bh->state = BUF_STATE_EMPTY;
 	}
@@ -3157,7 +3158,7 @@
 	}
 
 	/* Free the data buffers */
-	for (i = 0; i < FSG_NUM_BUFFERS; ++i)
+	for (i = 0; i < fsg_num_buffers; ++i)
 		kfree(fsg->buffhds[i].buf);
 
 	/* Free the request and buffer for endpoint 0 */
@@ -3445,7 +3446,7 @@
 	req->complete = ep0_complete;
 
 	/* Allocate the data buffers */
-	for (i = 0; i < FSG_NUM_BUFFERS; ++i) {
+	for (i = 0; i < fsg_num_buffers; ++i) {
 		struct fsg_buffhd	*bh = &fsg->buffhds[i];
 
 		/* Allocate for the bulk-in endpoint.  We assume that
@@ -3456,7 +3457,7 @@
 			goto out;
 		bh->next = bh + 1;
 	}
-	fsg->buffhds[FSG_NUM_BUFFERS - 1].next = &fsg->buffhds[0];
+	fsg->buffhds[fsg_num_buffers - 1].next = &fsg->buffhds[0];
 
 	/* This should reflect the actual gadget power source */
 	usb_gadget_set_selfpowered(gadget);
@@ -3572,7 +3573,9 @@
 {
 	struct fsg_dev		*fsg;
 
-	fsg = kzalloc(sizeof *fsg, GFP_KERNEL);
+	fsg = kzalloc(sizeof *fsg +
+		      fsg_num_buffers * sizeof *(fsg->buffhds), GFP_KERNEL);
+
 	if (!fsg)
 		return -ENOMEM;
 	spin_lock_init(&fsg->lock);
@@ -3590,6 +3593,10 @@
 	int		rc;
 	struct fsg_dev	*fsg;
 
+	rc = fsg_num_buffers_validate();
+	if (rc != 0)
+		return rc;
+
 	if ((rc = fsg_alloc()) != 0)
 		return rc;
 	fsg = the_fsg;
diff --git a/drivers/usb/gadget/storage_common.c b/drivers/usb/gadget/storage_common.c
index 3ea70d8..9fd3799 100644
--- a/drivers/usb/gadget/storage_common.c
+++ b/drivers/usb/gadget/storage_common.c
@@ -52,6 +52,12 @@
  * characters rather then a pointer to void.
  */
 
+/*
+ * When USB_GADGET_DEBUG_FILES is defined the module param num_buffers
+ * sets the number of pipeline buffers (length of the fsg_buffhd array).
+ * The valid range of num_buffers is: num >= 2 && num <= 4.
+ */
+
 
 #include <linux/usb/storage.h>
 #include <scsi/scsi.h>
@@ -264,8 +270,31 @@
 #define EP0_BUFSIZE	256
 #define DELAYED_STATUS	(EP0_BUFSIZE + 999)	/* An impossibly large value */
 
-/* Number of buffers we will use.  2 is enough for double-buffering */
-#define FSG_NUM_BUFFERS	2
+#ifdef CONFIG_USB_GADGET_DEBUG_FILES
+
+static unsigned int fsg_num_buffers = CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS;
+module_param_named(num_buffers, fsg_num_buffers, uint, S_IRUGO);
+MODULE_PARM_DESC(num_buffers, "Number of pipeline buffers");
+
+#else
+
+/*
+ * Number of buffers we will use.
+ * 2 is usually enough for good buffering pipeline
+ */
+#define fsg_num_buffers	CONFIG_USB_GADGET_STORAGE_NUM_BUFFERS
+
+#endif /* CONFIG_USB_DEBUG */
+
+/* check if fsg_num_buffers is within a valid range */
+static inline int fsg_num_buffers_validate(void)
+{
+	if (fsg_num_buffers >= 2 && fsg_num_buffers <= 4)
+		return 0;
+	pr_err("fsg_num_buffers %u is out of range (%d to %d)\n",
+	       fsg_num_buffers, 2 ,4);
+	return -EINVAL;
+}
 
 /* Default size of buffer length. */
 #define FSG_BUFLEN	((u32)16384)