| /* |
| * linux/arch/arm/mach-omap1/board-palmz71.c |
| * |
| * Modified from board-generic.c |
| * |
| * Support for the Palm Zire71 PDA. |
| * |
| * Original version : Laurent Gonzalez |
| * |
| * Modified for zire71 : Marek Vasut |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/kernel.h> |
| #include <linux/init.h> |
| #include <linux/platform_device.h> |
| #include <linux/notifier.h> |
| #include <linux/clk.h> |
| #include <linux/irq.h> |
| #include <linux/input.h> |
| #include <linux/interrupt.h> |
| #include <linux/mtd/mtd.h> |
| #include <linux/mtd/partitions.h> |
| |
| #include <mach/hardware.h> |
| #include <asm/mach-types.h> |
| #include <asm/mach/arch.h> |
| #include <asm/mach/map.h> |
| #include <asm/mach/flash.h> |
| |
| #include <mach/gpio.h> |
| #include <plat/mux.h> |
| #include <plat/usb.h> |
| #include <plat/dma.h> |
| #include <plat/tc.h> |
| #include <plat/board.h> |
| #include <plat/irda.h> |
| #include <plat/keypad.h> |
| #include <plat/common.h> |
| #include <plat/omap-alsa.h> |
| |
| #include <linux/spi/spi.h> |
| #include <linux/spi/ads7846.h> |
| |
| #define PALMZ71_USBDETECT_GPIO 0 |
| #define PALMZ71_PENIRQ_GPIO 6 |
| #define PALMZ71_MMC_WP_GPIO 8 |
| #define PALMZ71_HDQ_GPIO 11 |
| |
| #define PALMZ71_HOTSYNC_GPIO OMAP_MPUIO(1) |
| #define PALMZ71_CABLE_GPIO OMAP_MPUIO(2) |
| #define PALMZ71_SLIDER_GPIO OMAP_MPUIO(3) |
| #define PALMZ71_MMC_IN_GPIO OMAP_MPUIO(4) |
| |
| static void __init |
| omap_palmz71_init_irq(void) |
| { |
| omap1_init_common_hw(); |
| omap_init_irq(); |
| omap_gpio_init(); |
| } |
| |
| static int palmz71_keymap[] = { |
| KEY(0, 0, KEY_F1), |
| KEY(0, 1, KEY_F2), |
| KEY(0, 2, KEY_F3), |
| KEY(0, 3, KEY_F4), |
| KEY(0, 4, KEY_POWER), |
| KEY(1, 0, KEY_LEFT), |
| KEY(1, 1, KEY_DOWN), |
| KEY(1, 2, KEY_UP), |
| KEY(1, 3, KEY_RIGHT), |
| KEY(1, 4, KEY_ENTER), |
| KEY(2, 0, KEY_CAMERA), |
| 0, |
| }; |
| |
| static struct omap_kp_platform_data palmz71_kp_data = { |
| .rows = 8, |
| .cols = 8, |
| .keymap = palmz71_keymap, |
| .rep = 1, |
| .delay = 80, |
| }; |
| |
| static struct resource palmz71_kp_resources[] = { |
| [0] = { |
| .start = INT_KEYBOARD, |
| .end = INT_KEYBOARD, |
| .flags = IORESOURCE_IRQ, |
| }, |
| }; |
| |
| static struct platform_device palmz71_kp_device = { |
| .name = "omap-keypad", |
| .id = -1, |
| .dev = { |
| .platform_data = &palmz71_kp_data, |
| }, |
| .num_resources = ARRAY_SIZE(palmz71_kp_resources), |
| .resource = palmz71_kp_resources, |
| }; |
| |
| static struct mtd_partition palmz71_rom_partitions[] = { |
| /* PalmOS "Small ROM", contains the bootloader and the debugger */ |
| { |
| .name = "smallrom", |
| .offset = 0, |
| .size = 0xa000, |
| .mask_flags = MTD_WRITEABLE, |
| }, |
| /* PalmOS "Big ROM", a filesystem with all the OS code and data */ |
| { |
| .name = "bigrom", |
| .offset = SZ_128K, |
| /* |
| * 0x5f0000 bytes big in the multi-language ("EFIGS") version, |
| * 0x7b0000 bytes in the English-only ("enUS") version. |
| */ |
| .size = 0x7b0000, |
| .mask_flags = MTD_WRITEABLE, |
| }, |
| }; |
| |
| static struct flash_platform_data palmz71_rom_data = { |
| .map_name = "map_rom", |
| .name = "onboardrom", |
| .width = 2, |
| .parts = palmz71_rom_partitions, |
| .nr_parts = ARRAY_SIZE(palmz71_rom_partitions), |
| }; |
| |
| static struct resource palmz71_rom_resource = { |
| .start = OMAP_CS0_PHYS, |
| .end = OMAP_CS0_PHYS + SZ_8M - 1, |
| .flags = IORESOURCE_MEM, |
| }; |
| |
| static struct platform_device palmz71_rom_device = { |
| .name = "omapflash", |
| .id = -1, |
| .dev = { |
| .platform_data = &palmz71_rom_data, |
| }, |
| .num_resources = 1, |
| .resource = &palmz71_rom_resource, |
| }; |
| |
| static struct platform_device palmz71_lcd_device = { |
| .name = "lcd_palmz71", |
| .id = -1, |
| }; |
| |
| static struct omap_irda_config palmz71_irda_config = { |
| .transceiver_cap = IR_SIRMODE, |
| .rx_channel = OMAP_DMA_UART3_RX, |
| .tx_channel = OMAP_DMA_UART3_TX, |
| .dest_start = UART3_THR, |
| .src_start = UART3_RHR, |
| .tx_trigger = 0, |
| .rx_trigger = 0, |
| }; |
| |
| static struct resource palmz71_irda_resources[] = { |
| [0] = { |
| .start = INT_UART3, |
| .end = INT_UART3, |
| .flags = IORESOURCE_IRQ, |
| }, |
| }; |
| |
| static struct platform_device palmz71_irda_device = { |
| .name = "omapirda", |
| .id = -1, |
| .dev = { |
| .platform_data = &palmz71_irda_config, |
| }, |
| .num_resources = ARRAY_SIZE(palmz71_irda_resources), |
| .resource = palmz71_irda_resources, |
| }; |
| |
| static struct platform_device palmz71_spi_device = { |
| .name = "spi_palmz71", |
| .id = -1, |
| }; |
| |
| static struct omap_backlight_config palmz71_backlight_config = { |
| .default_intensity = 0xa0, |
| }; |
| |
| static struct platform_device palmz71_backlight_device = { |
| .name = "omap-bl", |
| .id = -1, |
| .dev = { |
| .platform_data = &palmz71_backlight_config, |
| }, |
| }; |
| |
| static struct platform_device *devices[] __initdata = { |
| &palmz71_rom_device, |
| &palmz71_kp_device, |
| &palmz71_lcd_device, |
| &palmz71_irda_device, |
| &palmz71_spi_device, |
| &palmz71_backlight_device, |
| }; |
| |
| static int |
| palmz71_get_pendown_state(void) |
| { |
| return !gpio_get_value(PALMZ71_PENIRQ_GPIO); |
| } |
| |
| static const struct ads7846_platform_data palmz71_ts_info = { |
| .model = 7846, |
| .vref_delay_usecs = 100, /* internal, no capacitor */ |
| .x_plate_ohms = 419, |
| .y_plate_ohms = 486, |
| .get_pendown_state = palmz71_get_pendown_state, |
| }; |
| |
| static struct spi_board_info __initdata palmz71_boardinfo[] = { { |
| /* MicroWire (bus 2) CS0 has an ads7846e */ |
| .modalias = "ads7846", |
| .platform_data = &palmz71_ts_info, |
| .irq = OMAP_GPIO_IRQ(PALMZ71_PENIRQ_GPIO), |
| .max_speed_hz = 120000 /* max sample rate at 3V */ |
| * 26 /* command + data + overhead */, |
| .bus_num = 2, |
| .chip_select = 0, |
| } }; |
| |
| static struct omap_usb_config palmz71_usb_config __initdata = { |
| .register_dev = 1, /* Mini-B only receptacle */ |
| .hmc_mode = 0, |
| .pins[0] = 2, |
| }; |
| |
| static struct omap_lcd_config palmz71_lcd_config __initdata = { |
| .ctrl_name = "internal", |
| }; |
| |
| static struct omap_board_config_kernel palmz71_config[] __initdata = { |
| {OMAP_TAG_LCD, &palmz71_lcd_config}, |
| }; |
| |
| static irqreturn_t |
| palmz71_powercable(int irq, void *dev_id) |
| { |
| if (gpio_get_value(PALMZ71_USBDETECT_GPIO)) { |
| printk(KERN_INFO "PM: Power cable connected\n"); |
| set_irq_type(gpio_to_irq(PALMZ71_USBDETECT_GPIO), |
| IRQ_TYPE_EDGE_FALLING); |
| } else { |
| printk(KERN_INFO "PM: Power cable disconnected\n"); |
| set_irq_type(gpio_to_irq(PALMZ71_USBDETECT_GPIO), |
| IRQ_TYPE_EDGE_RISING); |
| } |
| return IRQ_HANDLED; |
| } |
| |
| static void __init |
| omap_mpu_wdt_mode(int mode) |
| { |
| if (mode) |
| omap_writew(0x8000, OMAP_WDT_TIMER_MODE); |
| else { |
| omap_writew(0x00f5, OMAP_WDT_TIMER_MODE); |
| omap_writew(0x00a0, OMAP_WDT_TIMER_MODE); |
| } |
| } |
| |
| static void __init |
| palmz71_gpio_setup(int early) |
| { |
| if (early) { |
| /* Only set GPIO1 so we have a working serial */ |
| gpio_direction_output(1, 1); |
| } else { |
| /* Set MMC/SD host WP pin as input */ |
| if (gpio_request(PALMZ71_MMC_WP_GPIO, "MMC WP") < 0) { |
| printk(KERN_ERR "Could not reserve WP GPIO!\n"); |
| return; |
| } |
| gpio_direction_input(PALMZ71_MMC_WP_GPIO); |
| |
| /* Monitor the Power-cable-connected signal */ |
| if (gpio_request(PALMZ71_USBDETECT_GPIO, "USB detect") < 0) { |
| printk(KERN_ERR |
| "Could not reserve cable signal GPIO!\n"); |
| return; |
| } |
| gpio_direction_input(PALMZ71_USBDETECT_GPIO); |
| if (request_irq(gpio_to_irq(PALMZ71_USBDETECT_GPIO), |
| palmz71_powercable, IRQF_SAMPLE_RANDOM, |
| "palmz71-cable", 0)) |
| printk(KERN_ERR |
| "IRQ request for power cable failed!\n"); |
| palmz71_powercable(gpio_to_irq(PALMZ71_USBDETECT_GPIO), 0); |
| } |
| } |
| |
| static void __init |
| omap_palmz71_init(void) |
| { |
| /* mux pins for uarts */ |
| omap_cfg_reg(UART1_TX); |
| omap_cfg_reg(UART1_RTS); |
| omap_cfg_reg(UART2_TX); |
| omap_cfg_reg(UART2_RTS); |
| omap_cfg_reg(UART3_TX); |
| omap_cfg_reg(UART3_RX); |
| |
| palmz71_gpio_setup(1); |
| omap_mpu_wdt_mode(0); |
| |
| omap_board_config = palmz71_config; |
| omap_board_config_size = ARRAY_SIZE(palmz71_config); |
| |
| platform_add_devices(devices, ARRAY_SIZE(devices)); |
| |
| spi_register_board_info(palmz71_boardinfo, |
| ARRAY_SIZE(palmz71_boardinfo)); |
| omap_usb_init(&palmz71_usb_config); |
| omap_serial_init(); |
| omap_register_i2c_bus(1, 100, NULL, 0); |
| palmz71_gpio_setup(0); |
| } |
| |
| static void __init |
| omap_palmz71_map_io(void) |
| { |
| omap1_map_common_io(); |
| } |
| |
| MACHINE_START(OMAP_PALMZ71, "OMAP310 based Palm Zire71") |
| .phys_io = 0xfff00000, |
| .io_pg_offst = ((0xfef00000) >> 18) & 0xfffc, |
| .boot_params = 0x10000100,.map_io = omap_palmz71_map_io, |
| .init_irq = omap_palmz71_init_irq, |
| .init_machine = omap_palmz71_init, |
| .timer = &omap_timer, |
| MACHINE_END |