[libata] Add a bunch of PATA drivers.
The vast majority of drivers and changes are from Alan Cox. Albert Lee
contributed and maintains pata_pdc2027x. Adrian Bunk, Andrew Morton,
and Tejun Heo contributed various minor fixes and updates.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
new file mode 100644
index 0000000..d6ef3bf
--- /dev/null
+++ b/drivers/ata/pata_artop.c
@@ -0,0 +1,518 @@
+/*
+ * pata_artop.c - ARTOP ATA controller driver
+ *
+ * (C) 2006 Red Hat <alan@redhat.com>
+ *
+ * Based in part on drivers/ide/pci/aec62xx.c
+ * Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org>
+ * 865/865R fixes for Macintosh card version from a patch to the old
+ * driver by Thibaut VARENE <varenet@parisc-linux.org>
+ * When setting the PCI latency we must set 0x80 or higher for burst
+ * performance Alessandro Zummo <alessandro.zummo@towertech.it>
+ *
+ * TODO
+ * 850 serialization once the core supports it
+ * Investigate no_dsc on 850R
+ * Clock detect
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME "pata_artop"
+#define DRV_VERSION "0.4.1"
+
+/*
+ * The ARTOP has 33 Mhz and "over clocked" timing tables. Until we
+ * get PCI bus speed functionality we leave this as 0. Its a variable
+ * for when we get the functionality and also for folks wanting to
+ * test stuff.
+ */
+
+static int clock = 0;
+
+static int artop6210_pre_reset(struct ata_port *ap)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ const struct pci_bits artop_enable_bits[] = {
+ { 0x4AU, 1U, 0x02UL, 0x02UL }, /* port 0 */
+ { 0x4AU, 1U, 0x04UL, 0x04UL }, /* port 1 */
+ };
+
+ if (!pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) {
+ ata_port_disable(ap);
+ printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+ return 0;
+ }
+ ap->cbl = ATA_CBL_PATA40;
+ return ata_std_prereset(ap);
+}
+
+/**
+ * artop6210_error_handler - Probe specified port on PATA host controller
+ * @ap: Port to probe
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void artop6210_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, artop6210_pre_reset,
+ ata_std_softreset, NULL,
+ ata_std_postreset);
+}
+
+/**
+ * artop6260_pre_reset - check for 40/80 pin
+ * @ap: Port
+ *
+ * The ARTOP hardware reports the cable detect bits in register 0x49.
+ * Nothing complicated needed here.
+ */
+
+static int artop6260_pre_reset(struct ata_port *ap)
+{
+ static const struct pci_bits artop_enable_bits[] = {
+ { 0x4AU, 1U, 0x02UL, 0x02UL }, /* port 0 */
+ { 0x4AU, 1U, 0x04UL, 0x04UL }, /* port 1 */
+ };
+
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u8 tmp;
+
+ /* Odd numbered device ids are the units with enable bits (the -R cards) */
+ if (pdev->device % 1 && !pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) {
+ ata_port_disable(ap);
+ printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+ return 0;
+ }
+ pci_read_config_byte(pdev, 0x49, &tmp);
+ if (tmp & (1 >> ap->port_no))
+ ap->cbl = ATA_CBL_PATA40;
+ else
+ ap->cbl = ATA_CBL_PATA80;
+ return ata_std_prereset(ap);
+}
+
+/**
+ * artop6260_error_handler - Probe specified port on PATA host controller
+ * @ap: Port to probe
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void artop6260_error_handler(struct ata_port *ap)
+{
+ ata_bmdma_drive_eh(ap, artop6260_pre_reset,
+ ata_std_softreset, NULL,
+ ata_std_postreset);
+}
+
+/**
+ * artop6210_load_piomode - Load a set of PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device
+ * @pio: PIO mode
+ *
+ * Set PIO mode for device, in host controller PCI config space. This
+ * is used both to set PIO timings in PIO mode and also to set the
+ * matching PIO clocking for UDMA, as well as the MWDMA timings.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void artop6210_load_piomode(struct ata_port *ap, struct ata_device *adev, unsigned int pio)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int dn = adev->devno + 2 * ap->port_no;
+ const u16 timing[2][5] = {
+ { 0x0000, 0x000A, 0x0008, 0x0303, 0x0301 },
+ { 0x0700, 0x070A, 0x0708, 0x0403, 0x0401 }
+
+ };
+ /* Load the PIO timing active/recovery bits */
+ pci_write_config_word(pdev, 0x40 + 2 * dn, timing[clock][pio]);
+}
+
+/**
+ * artop6210_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device we are configuring
+ *
+ * Set PIO mode for device, in host controller PCI config space. For
+ * ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
+ * the event UDMA is used the later call to set_dmamode will set the
+ * bits as required.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void artop6210_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int dn = adev->devno + 2 * ap->port_no;
+ u8 ultra;
+
+ artop6210_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
+
+ /* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
+ pci_read_config_byte(pdev, 0x54, &ultra);
+ ultra &= ~(3 << (2 * dn));
+ pci_write_config_byte(pdev, 0x54, ultra);
+}
+
+/**
+ * artop6260_load_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device we are configuring
+ * @pio: PIO mode
+ *
+ * Set PIO mode for device, in host controller PCI config space. The
+ * ARTOP6260 and relatives store the timing data differently.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void artop6260_load_piomode (struct ata_port *ap, struct ata_device *adev, unsigned int pio)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int dn = adev->devno + 2 * ap->port_no;
+ const u8 timing[2][5] = {
+ { 0x00, 0x0A, 0x08, 0x33, 0x31 },
+ { 0x70, 0x7A, 0x78, 0x43, 0x41 }
+
+ };
+ /* Load the PIO timing active/recovery bits */
+ pci_write_config_byte(pdev, 0x40 + dn, timing[clock][pio]);
+}
+
+/**
+ * artop6260_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device we are configuring
+ *
+ * Set PIO mode for device, in host controller PCI config space. For
+ * ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
+ * the event UDMA is used the later call to set_dmamode will set the
+ * bits as required.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void artop6260_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u8 ultra;
+
+ artop6260_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
+
+ /* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
+ pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
+ ultra &= ~(7 << (4 * adev->devno)); /* One nibble per drive */
+ pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
+}
+
+/**
+ * artop6210_set_dmamode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: um
+ *
+ * Set DMA mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void artop6210_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int pio;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int dn = adev->devno + 2 * ap->port_no;
+ u8 ultra;
+
+ if (adev->dma_mode == XFER_MW_DMA_0)
+ pio = 1;
+ else
+ pio = 4;
+
+ /* Load the PIO timing active/recovery bits */
+ artop6210_load_piomode(ap, adev, pio);
+
+ pci_read_config_byte(pdev, 0x54, &ultra);
+ ultra &= ~(3 << (2 * dn));
+
+ /* Add ultra DMA bits if in UDMA mode */
+ if (adev->dma_mode >= XFER_UDMA_0) {
+ u8 mode = (adev->dma_mode - XFER_UDMA_0) + 1 - clock;
+ if (mode == 0)
+ mode = 1;
+ ultra |= (mode << (2 * dn));
+ }
+ pci_write_config_byte(pdev, 0x54, ultra);
+}
+
+/**
+ * artop6260_set_dmamode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device we are configuring
+ *
+ * Set DMA mode for device, in host controller PCI config space. The
+ * ARTOP6260 and relatives store the timing data differently.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void artop6260_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int pio = adev->pio_mode - XFER_PIO_0;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u8 ultra;
+
+ if (adev->dma_mode == XFER_MW_DMA_0)
+ pio = 1;
+ else
+ pio = 4;
+
+ /* Load the PIO timing active/recovery bits */
+ artop6260_load_piomode(ap, adev, pio);
+
+ /* Add ultra DMA bits if in UDMA mode */
+ pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
+ ultra &= ~(7 << (4 * adev->devno)); /* One nibble per drive */
+ if (adev->dma_mode >= XFER_UDMA_0) {
+ u8 mode = adev->dma_mode - XFER_UDMA_0 + 1 - clock;
+ if (mode == 0)
+ mode = 1;
+ ultra |= (mode << (4 * adev->devno));
+ }
+ pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
+}
+
+static struct scsi_host_template artop_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .max_sectors = ATA_MAX_SECTORS,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .bios_param = ata_std_bios_param,
+};
+
+static const struct ata_port_operations artop6210_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = artop6210_set_piomode,
+ .set_dmamode = artop6210_set_dmamode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = artop6210_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .eng_timeout = ata_eng_timeout,
+ .data_xfer = ata_pio_data_xfer,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = ata_host_stop,
+};
+
+static const struct ata_port_operations artop6260_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = artop6260_set_piomode,
+ .set_dmamode = artop6260_set_dmamode,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = artop6260_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_pio_data_xfer,
+
+ .eng_timeout = ata_eng_timeout,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+ .host_stop = ata_host_stop,
+};
+
+
+/**
+ * artop_init_one - Register ARTOP ATA PCI device with kernel services
+ * @pdev: PCI device to register
+ * @ent: Entry in artop_pci_tbl matching with @pdev
+ *
+ * Called from kernel PCI layer.
+ *
+ * LOCKING:
+ * Inherited from PCI layer (may sleep).
+ *
+ * RETURNS:
+ * Zero on success, or -ERRNO value.
+ */
+
+static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
+{
+ static int printed_version;
+ static struct ata_port_info info_6210 = {
+ .sht = &artop_sht,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = ATA_UDMA2,
+ .port_ops = &artop6210_ops,
+ };
+ static struct ata_port_info info_626x = {
+ .sht = &artop_sht,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = ATA_UDMA4,
+ .port_ops = &artop6260_ops,
+ };
+ static struct ata_port_info info_626x_fast = {
+ .sht = &artop_sht,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = ATA_UDMA5,
+ .port_ops = &artop6260_ops,
+ };
+ struct ata_port_info *port_info[2];
+ struct ata_port_info *info;
+ int ports = 2;
+
+ if (!printed_version++)
+ dev_printk(KERN_DEBUG, &pdev->dev,
+ "version " DRV_VERSION "\n");
+
+ if (id->driver_data == 0) { /* 6210 variant */
+ info = &info_6210;
+ /* BIOS may have left us in UDMA, clear it before libata probe */
+ pci_write_config_byte(pdev, 0x54, 0);
+ /* For the moment (also lacks dsc) */
+ printk(KERN_WARNING "ARTOP 6210 requires serialize functionality not yet supported by libata.\n");
+ printk(KERN_WARNING "Secondary ATA ports will not be activated.\n");
+ ports = 1;
+ }
+ else if (id->driver_data == 1) /* 6260 */
+ info = &info_626x;
+ else if (id->driver_data == 2) { /* 6260 or 6260 + fast */
+ unsigned long io = pci_resource_start(pdev, 4);
+ u8 reg;
+
+ info = &info_626x;
+ if (inb(io) & 0x10)
+ info = &info_626x_fast;
+ /* Mac systems come up with some registers not set as we
+ will need them */
+
+ /* Clear reset & test bits */
+ pci_read_config_byte(pdev, 0x49, ®);
+ pci_write_config_byte(pdev, 0x49, reg & ~ 0x30);
+
+ /* PCI latency must be > 0x80 for burst mode, tweak it
+ * if required.
+ */
+ pci_read_config_byte(pdev, PCI_LATENCY_TIMER, ®);
+ if (reg <= 0x80)
+ pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x90);
+
+ /* Enable IRQ output and burst mode */
+ pci_read_config_byte(pdev, 0x4a, ®);
+ pci_write_config_byte(pdev, 0x4a, (reg & ~0x01) | 0x80);
+
+ }
+ port_info[0] = port_info[1] = info;
+ return ata_pci_init_one(pdev, port_info, ports);
+}
+
+static const struct pci_device_id artop_pci_tbl[] = {
+ { 0x1191, 0x0005, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+ { 0x1191, 0x0006, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
+ { 0x1191, 0x0007, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
+ { 0x1191, 0x0008, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
+ { 0x1191, 0x0009, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
+ { } /* terminate list */
+};
+
+static struct pci_driver artop_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = artop_pci_tbl,
+ .probe = artop_init_one,
+ .remove = ata_pci_remove_one,
+};
+
+static int __init artop_init(void)
+{
+ return pci_register_driver(&artop_pci_driver);
+}
+
+static void __exit artop_exit(void)
+{
+ pci_unregister_driver(&artop_pci_driver);
+}
+
+
+module_init(artop_init);
+module_exit(artop_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for ARTOP PATA");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, artop_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+