blob: 6ab568428a14bc24f15985d286939fb90755251d [file] [log] [blame]
/*
* pata_amd.c - AMD PATA for new ATA layer
* (C) 2005-2006 Red Hat Inc
* Alan Cox <alan@redhat.com>
*
* Based on pata-sil680. Errata information is taken from data sheets
* and the amd74xx.c driver by Vojtech Pavlik. Nvidia SATA devices are
* claimed by sata-nv.c.
*
* TODO:
* Variable system clock when/if it makes sense
* Power management on ports
*
*
* Documentation publically available.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_amd"
#define DRV_VERSION "0.2.2"
/**
* timing_setup - shared timing computation and load
* @ap: ATA port being set up
* @adev: drive being configured
* @offset: port offset
* @speed: target speed
* @clock: clock multiplier (number of times 33MHz for this part)
*
* Perform the actual timing set up for Nvidia or AMD PATA devices.
* The actual devices vary so they all call into this helper function
* providing the clock multipler and offset (because AMD and Nvidia put
* the ports at different locations).
*/
static void timing_setup(struct ata_port *ap, struct ata_device *adev, int offset, int speed, int clock)
{
static const unsigned char amd_cyc2udma[] = {
6, 6, 5, 4, 0, 1, 1, 2, 2, 3, 3, 3, 3, 3, 3, 7
};
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct ata_device *peer = ata_dev_pair(adev);
int dn = ap->port_no * 2 + adev->devno;
struct ata_timing at, apeer;
int T, UT;
const int amd_clock = 33333; /* KHz. */
u8 t;
T = 1000000000 / amd_clock;
UT = T / min_t(int, max_t(int, clock, 1), 2);
if (ata_timing_compute(adev, speed, &at, T, UT) < 0) {
dev_printk(KERN_ERR, &pdev->dev, "unknown mode %d.\n", speed);
return;
}
if (peer) {
/* This may be over conservative */
if (peer->dma_mode) {
ata_timing_compute(peer, peer->dma_mode, &apeer, T, UT);
ata_timing_merge(&apeer, &at, &at, ATA_TIMING_8BIT);
}
ata_timing_compute(peer, peer->pio_mode, &apeer, T, UT);
ata_timing_merge(&apeer, &at, &at, ATA_TIMING_8BIT);
}
if (speed == XFER_UDMA_5 && amd_clock <= 33333) at.udma = 1;
if (speed == XFER_UDMA_6 && amd_clock <= 33333) at.udma = 15;
/*
* Now do the setup work
*/
/* Configure the address set up timing */
pci_read_config_byte(pdev, offset + 0x0C, &t);
t = (t & ~(3 << ((3 - dn) << 1))) | ((FIT(at.setup, 1, 4) - 1) << ((3 - dn) << 1));
pci_write_config_byte(pdev, offset + 0x0C , t);
/* Configure the 8bit I/O timing */
pci_write_config_byte(pdev, offset + 0x0E + (1 - (dn >> 1)),
((FIT(at.act8b, 1, 16) - 1) << 4) | (FIT(at.rec8b, 1, 16) - 1));
/* Drive timing */
pci_write_config_byte(pdev, offset + 0x08 + (3 - dn),
((FIT(at.active, 1, 16) - 1) << 4) | (FIT(at.recover, 1, 16) - 1));
switch (clock) {
case 1:
t = at.udma ? (0xc0 | (FIT(at.udma, 2, 5) - 2)) : 0x03;
break;
case 2:
t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 2, 10)]) : 0x03;
break;
case 3:
t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 1, 10)]) : 0x03;
break;
case 4:
t = at.udma ? (0xc0 | amd_cyc2udma[FIT(at.udma, 1, 15)]) : 0x03;
break;
default:
return;
}
/* UDMA timing */
pci_write_config_byte(pdev, offset + 0x10 + (3 - dn), t);
}
/**
* amd_probe_init - cable detection
* @ap: ATA port
*
* Perform cable detection. The BIOS stores this in PCI config
* space for us.
*/
static int amd_pre_reset(struct ata_port *ap)
{
static const u32 bitmask[2] = {0x03, 0xC0};
static const struct pci_bits amd_enable_bits[] = {
{ 0x40, 1, 0x02, 0x02 },
{ 0x40, 1, 0x01, 0x01 }
};
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u8 ata66;
if (!pci_test_config_bits(pdev, &amd_enable_bits[ap->port_no])) {
ata_port_disable(ap);
printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
return 0;
}
pci_read_config_byte(pdev, 0x42, &ata66);
if (ata66 & bitmask[ap->port_no])
ap->cbl = ATA_CBL_PATA80;
else
ap->cbl = ATA_CBL_PATA40;
return ata_std_prereset(ap);
}
static void amd_error_handler(struct ata_port *ap)
{
return ata_bmdma_drive_eh(ap, amd_pre_reset,
ata_std_softreset, NULL,
ata_std_postreset);
}
static int amd_early_pre_reset(struct ata_port *ap)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
static struct pci_bits amd_enable_bits[] = {
{ 0x40, 1, 0x02, 0x02 },
{ 0x40, 1, 0x01, 0x01 }
};
if (!pci_test_config_bits(pdev, &amd_enable_bits[ap->port_no])) {
ata_port_disable(ap);
printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
return 0;
}
/* No host side cable detection */
ap->cbl = ATA_CBL_PATA80;
return ata_std_prereset(ap);
}
static void amd_early_error_handler(struct ata_port *ap)
{
ata_bmdma_drive_eh(ap, amd_early_pre_reset,
ata_std_softreset, NULL,
ata_std_postreset);
}
/**
* amd33_set_piomode - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Program the AMD registers for PIO mode.
*/
static void amd33_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x40, adev->pio_mode, 1);
}
static void amd66_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x40, adev->pio_mode, 2);
}
static void amd100_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x40, adev->pio_mode, 3);
}
static void amd133_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x40, adev->pio_mode, 4);
}
/**
* amd33_set_dmamode - set initial DMA mode data
* @ap: ATA interface
* @adev: ATA device
*
* Program the MWDMA/UDMA modes for the AMD and Nvidia
* chipset.
*/
static void amd33_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x40, adev->dma_mode, 1);
}
static void amd66_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x40, adev->dma_mode, 2);
}
static void amd100_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x40, adev->dma_mode, 3);
}
static void amd133_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x40, adev->dma_mode, 4);
}
/**
* nv_probe_init - cable detection
* @ap: ATA port
*
* Perform cable detection. The BIOS stores this in PCI config
* space for us.
*/
static int nv_pre_reset(struct ata_port *ap) {
static const u8 bitmask[2] = {0x03, 0xC0};
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u8 ata66;
u16 udma;
pci_read_config_byte(pdev, 0x52, &ata66);
if (ata66 & bitmask[ap->port_no])
ap->cbl = ATA_CBL_PATA80;
else
ap->cbl = ATA_CBL_PATA40;
/* We now have to double check because the Nvidia boxes BIOS
doesn't always set the cable bits but does set mode bits */
pci_read_config_word(pdev, 0x62 - 2 * ap->port_no, &udma);
if ((udma & 0xC4) == 0xC4 || (udma & 0xC400) == 0xC400)
ap->cbl = ATA_CBL_PATA80;
return ata_std_prereset(ap);
}
static void nv_error_handler(struct ata_port *ap)
{
ata_bmdma_drive_eh(ap, nv_pre_reset,
ata_std_softreset, NULL,
ata_std_postreset);
}
/**
* nv100_set_piomode - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Program the AMD registers for PIO mode.
*/
static void nv100_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x50, adev->pio_mode, 3);
}
static void nv133_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x50, adev->pio_mode, 4);
}
/**
* nv100_set_dmamode - set initial DMA mode data
* @ap: ATA interface
* @adev: ATA device
*
* Program the MWDMA/UDMA modes for the AMD and Nvidia
* chipset.
*/
static void nv100_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x50, adev->dma_mode, 3);
}
static void nv133_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
timing_setup(ap, adev, 0x50, adev->dma_mode, 4);
}
static struct scsi_host_template amd_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
.max_sectors = ATA_MAX_SECTORS,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
};
static struct ata_port_operations amd33_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = amd33_set_piomode,
.set_dmamode = amd33_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = amd_early_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.eng_timeout = ata_eng_timeout,
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop
};
static struct ata_port_operations amd66_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = amd66_set_piomode,
.set_dmamode = amd66_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = amd_early_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.eng_timeout = ata_eng_timeout,
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop
};
static struct ata_port_operations amd100_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = amd100_set_piomode,
.set_dmamode = amd100_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = amd_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.eng_timeout = ata_eng_timeout,
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop
};
static struct ata_port_operations amd133_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = amd133_set_piomode,
.set_dmamode = amd133_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = amd_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.eng_timeout = ata_eng_timeout,
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop
};
static struct ata_port_operations nv100_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = nv100_set_piomode,
.set_dmamode = nv100_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = nv_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.eng_timeout = ata_eng_timeout,
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop
};
static struct ata_port_operations nv133_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = nv133_set_piomode,
.set_dmamode = nv133_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = nv_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.eng_timeout = ata_eng_timeout,
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
.port_stop = ata_port_stop,
.host_stop = ata_host_stop
};
static int amd_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static struct ata_port_info info[10] = {
{ /* 0: AMD 7401 */
.sht = &amd_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07, /* No SWDMA */
.udma_mask = 0x07, /* UDMA 33 */
.port_ops = &amd33_port_ops
},
{ /* 1: Early AMD7409 - no swdma */
.sht = &amd_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x1f, /* UDMA 66 */
.port_ops = &amd66_port_ops
},
{ /* 2: AMD 7409, no swdma errata */
.sht = &amd_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x1f, /* UDMA 66 */
.port_ops = &amd66_port_ops
},
{ /* 3: AMD 7411 */
.sht = &amd_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x3f, /* UDMA 100 */
.port_ops = &amd100_port_ops
},
{ /* 4: AMD 7441 */
.sht = &amd_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x3f, /* UDMA 100 */
.port_ops = &amd100_port_ops
},
{ /* 5: AMD 8111*/
.sht = &amd_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x7f, /* UDMA 133, no swdma */
.port_ops = &amd133_port_ops
},
{ /* 6: AMD 8111 UDMA 100 (Serenade) */
.sht = &amd_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x3f, /* UDMA 100, no swdma */
.port_ops = &amd133_port_ops
},
{ /* 7: Nvidia Nforce */
.sht = &amd_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x3f, /* UDMA 100 */
.port_ops = &nv100_port_ops
},
{ /* 8: Nvidia Nforce2 and later */
.sht = &amd_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x7f, /* UDMA 133, no swdma */
.port_ops = &nv133_port_ops
},
{ /* 9: AMD CS5536 (Geode companion) */
.sht = &amd_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x3f, /* UDMA 100 */
.port_ops = &amd100_port_ops
}
};
static struct ata_port_info *port_info[2];
static int printed_version;
int type = id->driver_data;
u8 rev;
u8 fifo;
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
pci_read_config_byte(pdev, 0x41, &fifo);
/* Check for AMD7409 without swdma errata and if found adjust type */
if (type == 1 && rev > 0x7)
type = 2;
/* Check for AMD7411 */
if (type == 3)
/* FIFO is broken */
pci_write_config_byte(pdev, 0x41, fifo & 0x0F);
else
pci_write_config_byte(pdev, 0x41, fifo | 0xF0);
/* Serenade ? */
if (type == 5 && pdev->subsystem_vendor == PCI_VENDOR_ID_AMD &&
pdev->subsystem_device == PCI_DEVICE_ID_AMD_SERENADE)
type = 6; /* UDMA 100 only */
if (type < 3)
ata_pci_clear_simplex(pdev);
/* And fire it up */
port_info[0] = port_info[1] = &info[type];
return ata_pci_init_one(pdev, port_info, 2);
}
static const struct pci_device_id amd[] = {
{ PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_COBRA_7401, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
{ PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7409, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1 },
{ PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7411, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3 },
{ PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_OPUS_7441, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
{ PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5 },
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 7 },
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
{ PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
{ PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 9 },
{ 0, },
};
static struct pci_driver amd_pci_driver = {
.name = DRV_NAME,
.id_table = amd,
.probe = amd_init_one,
.remove = ata_pci_remove_one
};
static int __init amd_init(void)
{
return pci_register_driver(&amd_pci_driver);
}
static void __exit amd_exit(void)
{
pci_unregister_driver(&amd_pci_driver);
}
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for AMD PATA IDE");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, amd);
MODULE_VERSION(DRV_VERSION);
module_init(amd_init);
module_exit(amd_exit);