arch/arm/boot/dts/msm8974-cdp.dtsi - kernel/msm - Gitiles

 /* Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 and
  * only version 2 as published by the Free Software Foundation.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  */

 /include/ "dsi-panel-toshiba-720p-video.dtsi"
 /include/ "dsi-panel-orise-720p-video.dtsi"
 /include/ "msm8974-leds.dtsi"
 /include/ "msm8974-camera-sensor-cdp.dtsi"

 / {
 	serial@f991e000 {
 		status = "ok";
 	};

 	qcom,mdss_dsi_toshiba_720p_video {
 		status = "ok";
 		qcom,cont-splash-enabled;
 	};

 	qcom,mdss_dsi_orise_720p_video {
 		status = "disable";
 	};

 	qcom,hdmi_tx@fd922100 {
 		status = "ok";
 	};

 	i2c@f9924000 {
 		atmel_mxt_ts@4a {
 			compatible = "atmel,mxt-ts";
 			reg = <0x4a>;
 			interrupt-parent = <&msmgpio>;
 			interrupts = <61 0x2>;
 			vdd_ana-supply = <&pm8941_l18>;
 			vcc_i2c-supply = <&pm8941_lvs1>;
 			atmel,reset-gpio = <&msmgpio 60 0x00>;
 			atmel,irq-gpio = <&msmgpio 61 0x00>;
 			atmel,panel-coords = <0  0 760 1424>;
 			atmel,display-coords = <0 0 720 1280>;
 			atmel,i2c-pull-up;
 			atmel,no-force-update;
 			atmel,cfg_1 {
 				atmel,family-id = <0x82>;
 				atmel,variant-id = <0x19>;
 				atmel,version = <0x10>;
 				atmel,build = <0xaa>;
 				atmel,config = [
 					/* Object 6, Instance = 0 */
 					00 00 00 00 00 00
 					/* Object 38, Instance = 0 */
 					15 01 00 03 0A 0C 00 00
 					/* Object 7, Instance = 0 */
 					20 08 32 03
 					/* Object 8, Instance = 0 */
 					0F 00 0A 0A 00 00 0A 0A 00 00
 					/* Object 9, Instance = 0 */
 					83 00 00 18 0E 00 70 46 02 01
 					00 0A 03 31 04 05 0A 0A 90 05
 					F8 02 05 F1 F1 0F 00 00 08 2D
 					12 06 00 00 00 01
 					/* Object 15, Instance = 0 */
 					00 00 00 00 00 00 00 00 00 00
 					00
 					/* Object 18, Instance = 0 */
 					00 00
 					/* Object 19, Instance = 0 */
 					00 00 00 00 00 00
 					/* Object 23, Instance = 0 */
 					00 00 00 00 00 00 00 00 00 00
 					00 00 00 00 00
 					/* Object 25, Instance = 0 */
 					00 00 00 00 00 00 00 00 00 00
 					00 00 00 00 00
 					/* Object 40, Instance = 0 */
 					00 00 00 00 00
 					/* Object 42, Instance = 0 */
 					33 1E 19 10 80 00 00 00 FF 00
 					/* Object 46, Instance = 0 */
 					00 00 10 10 00 00 03 00 00 01
 					/* Object 47, Instance = 0 */
 					08 0A 28 0A 02 0A 00 8C 00 20
 					00 00 00
 					/* Object 55, Instance = 0 */
 					00 00 00 00 00 00
 					/* Object 56, Instance = 0 */
 					00 00 00 18 05 05 05 05 05 05
 					05 05 05 05 05 05 05 05 05 05
 					05 05 05 05 05 05 05 05 00 00
 					00 00 00 00 00 00 00 00 00 00
 					00 00
 					/* Object 57, Instance = 0 */
 					00 00 00
 					/* Object 61, Instance = 0 */
 					00 00 00 00 00
 					/* Object 62, Instance = 0 */
 					01 2A 00 16 00 00 00 00 0B 01
 					02 03 04 08 00 00 08 10 18 05
 					00 0A 05 05 50 14 19 34 1A 7F
 					00 00 00 00 00 00 00 00 00 30
 					05 02 00 01 00 05 00 00 00 00
 					00 00 00 00
 					];
 			};
 		};
 	};

 	gen-vkeys {
 		compatible = "qcom,gen-vkeys";
 		label = "atmel_mxt_ts";
 		qcom,disp-maxx = <720>;
 		qcom,disp-maxy = <1280>;
 		qcom,panel-maxx = <760>;
 		qcom,panel-maxy = <1424>;
 		qcom,key-codes = <158 139 102 217>;
 	};

 	i2c@f9967000 {
 		isa1200@48 {
 			status = "okay";
 			reg = <0x48>;
 			vcc_i2c-supply = <&pm8941_s3>;
 			compatible = "imagis,isa1200";
 			label = "vibrator";
 			imagis,chip-en;
 			imagis,smart-en;
 			imagis,need-pwm-clk;
 			imagis,ext-clk-en;
 			imagis,hap-en-gpio = <&msmgpio 86 0x00>;
 			imagis,max-timeout = <15000>;
 			imagis,pwm-div = <256>;
 			imagis,mode-ctrl = <2>;
 			imagis,regulator {
 				regulator-name = "vcc_i2c";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-max-microamp = <9360>;
 			};
 		};
 	};

 	gpio_keys {
 		compatible = "gpio-keys";
 		input-name = "gpio-keys";

 		camera_snapshot {
 			label = "camera_snapshot";
 			gpios = <&pm8941_gpios 3 0x1>;
 			linux,input-type = <1>;
 			linux,code = <0x2fe>;
 			gpio-key,wakeup;
 			debounce-interval = <15>;
 		};

 		camera_focus {
 			label = "camera_focus";
 			gpios = <&pm8941_gpios 4 0x1>;
 			linux,input-type = <1>;
 			linux,code = <0x210>;
 			gpio-key,wakeup;
 			debounce-interval = <15>;
 		};

 		vol_up {
 			label = "volume_up";
 			gpios = <&pm8941_gpios 5 0x1>;
 			linux,input-type = <1>;
 			linux,code = <115>;
 			gpio-key,wakeup;
 			debounce-interval = <15>;
 		};
 	};

 	spi@f9923000 {
 		ethernet-switch@2 {
 			compatible = "micrel,ks8851";
 			reg = <2>;
 			interrupt-parent = <&msmgpio>;
 			interrupts = <94 0>;
 			spi-max-frequency = <4800000>;
 			rst-gpio = <&pm8941_mpps 6 0>;
 			vdd-io-supply = <&spi_eth_vreg>;
 			vdd-phy-supply = <&spi_eth_vreg>;
 		};
 	};

 	sound {
 		qcom,model = "msm8974-taiko-cdp-snd-card";
 		qcom,hdmi-audio-rx;
 		qcom,us-euro-gpios = <&pm8941_gpios 20 0>;
 	};

 	usb2_otg_sw: regulator-tpd4s214 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb2_otg_sw";
 		gpio = <&pm8941_gpios 18 0>;
 		parent-supply = <&pm8941_boost>;
 		startup-delay-us = <17000>;
 		enable-active-high;
 	};

 	hsic_host: hsic@f9a00000 {
 		compatible = "qcom,hsic-host";
 		reg = <0xf9a00000 0x400>;
 		#address-cells = <0>;
 		interrupt-parent = <&hsic_host>;
 		interrupts = <0 1 2>;
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0xffffffff>;
 		interrupt-map = <0 &intc 0 136 0
 			1 &intc 0 148 0
 			2 &msmgpio 144 0x8>;
 		interrupt-names = "core_irq", "async_irq", "wakeup";
 		HSIC_VDDCX-supply = <&pm8841_s2>;
 		HSIC_GDSC-supply = <&gdsc_usb_hsic>;
 		hsic,strobe-gpio = <&msmgpio 144 0x00>;
 		hsic,data-gpio = <&msmgpio 145 0x00>;
 		hsic,resume-gpio = <&msmgpio 80 0x00>;
 		hsic,ignore-cal-pad-config;
 		hsic,strobe-pad-offset = <0x2050>;
 		hsic,data-pad-offset = <0x2054>;

 		qcom,msm-bus,name = "hsic";
 		qcom,msm-bus,num-cases = <2>;
 		qcom,msm-bus,num-paths = <1>;
 		qcom,msm-bus,vectors-KBps =
 				<85 512 0 0>,
 				<85 512 40000 160000>;
         };

 	wlan0: qca,wlan {
 		compatible = "qca,ar6004-hsic";
 		qcom,msm-bus,name = "wlan";
 		qcom,msm-bus,num-cases = <5>;
 		qcom,msm-bus,active-only = <0>;
 		qcom,msm-bus,num-paths = <1>;
 		qcom,msm-bus,vectors-KBps =
 				<85 512 0 0>,
 				<85 512 40000 160000>,
 				<85 512 40000 320000>,
 				<85 512 40000 480000>,
 				<85 512 40000 640000>;
 	};
 };

 &spmi_bus {
 	qcom,pm8941@1 {
 		qcom,leds@d800 {
 			status = "okay";
 			qcom,wled_0 {
 				label = "wled";
 				linux,name = "wled:backlight";
 				linux,default-trigger = "bkl-trigger";
 				qcom,cs-out-en;
 				qcom,op-fdbck = <1>;
 				qcom,default-state = "on";
 				qcom,max-current = <25>;
 				qcom,ctrl-delay-us = <0>;
 				qcom,boost-curr-lim = <3>;
 				qcom,cp-sel = <0>;
 				qcom,switch-freq = <2>;
 				qcom,ovp-val = <2>;
 				qcom,num-strings = <1>;
 				qcom,id = <0>;
 			};
 		};

 		qcom,leds@d900 {
 			status = "disabled";
 		};

 		qcom,leds@da00 {
 			status = "disabled";
 		};

 		qcom,leds@db00 {
 			status = "disabled";
 		};

 		qcom,leds@dc00 {
 			status = "disabled";
 		};

 		qcom,leds@dd00 {
 			status = "disabled";
 		};

 		qcom,leds@de00 {
 			status = "disabled";
 		};

 		qcom,leds@df00 {
 			status = "disabled";
 		};

 		qcom,leds@e000 {
 			status = "disabled";
 		};

 		qcom,leds@e100 {
 			status = "disabled";
 		};
 	};
 };

 &sdcc1 {
        status = "disabled";
 };

 &sdcc2 {
 	#address-cells = <0>;
 	interrupt-parent = <&sdcc2>;
 	interrupts = <0 1 2>;
 	#interrupt-cells = <1>;
 	interrupt-map-mask = <0xffffffff>;
 	interrupt-map = <0 &intc 0 125 0
 			1 &intc 0 220 0
 			2 &msmgpio 62 0x3>;
 	interrupt-names = "core_irq", "bam_irq", "status_irq";
 	cd-gpios = <&msmgpio 62 0x1>;
 	wp-gpios = <&pm8941_gpios 29 0x1>;
 	status = "disabled";
 };

 &sdhc_1 {
 	vdd-supply = <&pm8941_l20>;
 	vdd-io-supply = <&pm8941_s3>;

 	qcom,vdd-always-on;
 	qcom,vdd-lpm-sup;
 	qcom,vdd-voltage-level = <2950000 2950000>;
 	qcom,vdd-current-level = <800 500000>;

 	qcom,vdd-io-always-on;
 	qcom,vdd-io-voltage-level = <1800000 1800000>;
 	qcom,vdd-io-current-level = <250 154000>;

 	qcom,pad-pull-on = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
 	qcom,pad-pull-off = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
 	qcom,pad-drv-on = <0x4 0x4 0x4>; /* 10mA, 10mA, 10mA */
 	qcom,pad-drv-off = <0x0 0x0 0x0>; /* 2mA, 2mA, 2mA */

 	qcom,nonremovable;
 	status = "ok";
 };

 &sdhc_2 {
 	#address-cells = <0>;
 	interrupt-parent = <&sdhc_2>;
 	interrupts = <0 1 2>;
 	#interrupt-cells = <1>;
 	interrupt-map-mask = <0xffffffff>;
 	interrupt-map = <0 &intc 0 125 0
 			1 &intc 0 221 0
 			2 &msmgpio 62 0x3>;
 	interrupt-names = "hc_irq", "pwr_irq", "status_irq";
 	cd-gpios = <&msmgpio 62 0x1>;

 	vdd-supply = <&pm8941_l21>;
 	vdd-io-supply = <&pm8941_l13>;

 	qcom,vdd-voltage-level = <2950000 2950000>;
 	qcom,vdd-current-level = <9000 800000>;

 	qcom,vdd-io-voltage-level = <1800000 2950000>;
 	qcom,vdd-io-current-level = <6 22000>;

 	qcom,pad-pull-on = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
 	qcom,pad-pull-off = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
 	qcom,pad-drv-on = <0x4 0x4 0x4>; /* 10mA, 10mA, 10mA */
 	qcom,pad-drv-off = <0x0 0x0 0x0>; /* 2mA, 2mA, 2mA */
 	status = "ok";
 };

 /* Drive strength recommendations for clock line from hardware team is 10 mA.
  * But since the driver has been been using the below values from the start
  * without any problems, continue to use those.
  */
 &sdcc1 {
 	qcom,pad-drv-on = <0x7 0x4 0x4>; /* 16mA, 10mA, 10mA */
 };

 &sdcc2 {
 	qcom,pad-drv-on = <0x7 0x4 0x4>; /* 16mA, 10mA, 10mA */
 };

 &sdhc_1 {
 	qcom,pad-drv-on = <0x7 0x4 0x4>; /* 16mA, 10mA, 10mA */
 };

 &sdhc_2 {
 	qcom,pad-drv-on = <0x7 0x4 0x4>; /* 16mA, 10mA, 10mA */
 };

 &uart7 {
 	status = "ok";
 	qcom,tx-gpio = <&msmgpio 41 0x00>;
 	qcom,rx-gpio = <&msmgpio 42 0x00>;
 	qcom,cts-gpio = <&msmgpio 43 0x00>;
 	qcom,rfr-gpio = <&msmgpio 44 0x00>;
 };

 &usb3 {
 	qcom,otg-capability;
 };

 &pm8941_chg {
 	status = "ok";

 	qcom,chgr@1000 {
 		status = "ok";
 	};

 	qcom,buck@1100 {
 		status = "ok";
 	};

 	qcom,usb-chgpth@1300 {
 		status = "ok";
 	};

 	qcom,dc-chgpth@1400 {
 		status = "ok";
 	};

 	qcom,boost@1500 {
 		status = "ok";
 	};

 	qcom,chg-misc@1600 {
 		status = "ok";
 	};
 };

 &pm8941_gpios {
 	gpio@c000 { /* GPIO 1 */
 	};

 	gpio@c100 { /* GPIO 2 */
 	};

 	gpio@c200 { /* GPIO 3 */
 		qcom,mode = <0>;
 		qcom,pull = <0>;
 		qcom,vin-sel = <2>;
 		qcom,src-sel = <0>;
 	};

 	gpio@c300 { /* GPIO 4 */
 		qcom,mode = <0>;
 		qcom,pull = <0>;
 		qcom,vin-sel = <2>;
 		qcom,src-sel = <0>;
 	};

 	gpio@c400 { /* GPIO 5 */
 		qcom,mode = <0>;
 		qcom,pull = <0>;
 		qcom,vin-sel = <2>;
 		qcom,src-sel = <0>;
 	};

 	gpio@c500 { /* GPIO 6 */
 	};

 	gpio@c600 { /* GPIO 7 */
 	};

 	gpio@c700 { /* GPIO 8 */
 	};

 	gpio@c800 { /* GPIO 9 */
 	};

 	gpio@c900 { /* GPIO 10 */
 	};

 	gpio@ca00 { /* GPIO 11 */
 	};

 	gpio@cb00 { /* GPIO 12 */
 	};

 	gpio@cc00 { /* GPIO 13 */
 	};

 	gpio@cd00 { /* GPIO 14 */
 	};

 	gpio@ce00 { /* GPIO 15 */
 		qcom,mode = <1>;
 		qcom,output-type = <0>;
 		qcom,pull = <5>;
 		qcom,vin-sel = <2>;
 		qcom,out-strength = <3>;
 		qcom,src-sel = <2>;
 		qcom,master-en = <1>;
 	};

 	gpio@cf00 { /* GPIO 16 */
 		qcom,mode = <1>;
 		qcom,output-type = <0>;
 		qcom,pull = <2>;
 		qcom,vin-sel = <2>;
 		qcom,out-strength = <2>;
 		qcom,src-sel = <2>;
 		qcom,master-en = <1>;
 	};

 	gpio@d000 { /* GPIO 17 */
 	};

 	gpio@d100 { /* GPIO 18 */
 		/* usb2_otg_sw regulator enable */
 		qcom,mode = <1>;		/* Digital output */
 		qcom,output-type = <0>;		/* CMOS logic */
 		qcom,invert = <0>; 		/* Output low initially */
 		qcom,vin-sel = <2>; 		/* PM8941 S3 = 1.8 V */
 		qcom,src-sel = <0>; 		/* Constant */
 		qcom,out-strength = <2>;	/* Medium drive strength */
 		qcom,master-en = <1>;		/* Enable GPIO */
 	};

 	gpio@d200 { /* GPIO 19 */
 		qcom,mode = <1>;		/* QPNP_PIN_MODE_DIG_OUT */
 		qcom,output-type = <0>;		/* QPNP_PIN_OUT_BUF_CMOS */
 		qcom,pull = <5>;		/* QPNP_PIN_PULL_NO */
 		qcom,vin-sel = <2>;		/* QPNP_PIN_VIN2 */
 		qcom,out-strength = <2>;	/* QPNP_PIN_OUT_STRENGTH_MED */
 		qcom,src-sel = <0>;		/* QPNP_PIN_SEL_FUNC_CONSTANT */
 		qcom,master-en = <1>;
 	};

 	gpio@d300 { /* GPIO 20 */
 		qcom,mode = <1>;		/* QPNP_PIN_MODE_DIG_OUT */
 		qcom,output-type = <0>;		/* QPNP_PIN_OUT_BUF_CMOS */
 		qcom,invert = <0>; 		/* Output low initially */
 		qcom,pull = <5>;		/* QPNP_PIN_PULL_NO */
 		qcom,vin-sel = <2>;		/* QPNP_PIN_VIN2 */
 		qcom,out-strength = <2>;	/* QPNP_PIN_OUT_STRENGTH_MED */
 		qcom,src-sel = <0>;		/* QPNP_PIN_SEL_FUNC_CONSTANT */
 		qcom,master-en = <1>;
 	};

 	gpio@d400 { /* GPIO 21 */
 	};

 	gpio@d500 { /* GPIO 22 */
 	};

 	gpio@d600 { /* GPIO 23 */
 	};

 	gpio@d700 { /* GPIO 24 */
 	};

 	gpio@d800 { /* GPIO 25 */
 	};

 	gpio@d900 { /* GPIO 26 */
 	};

 	gpio@da00 { /* GPIO 27 */
 	};

 	gpio@db00 { /* GPIO 28 */
 	};

 	gpio@dc00 { /* GPIO 29 */
 		qcom,pull = <0>; /* set to default pull */
 		qcom,master-en = <1>;
 		qcom,vin-sel = <2>; /* select 1.8 V source */
 	};

 	gpio@dd00 { /* GPIO 30 */
 	};

 	gpio@de00 { /* GPIO 31 */
 	};

 	gpio@df00 { /* GPIO 32 */
 	};

 	gpio@e000 { /* GPIO 33 */
 	};

 	gpio@e100 { /* GPIO 34 */
 	};

 	gpio@e200 { /* GPIO 35 */
 	};

 	gpio@e300 { /* GPIO 36 */
 	};
 };

 &pm8941_mpps {

 	mpp@a000 { /* MPP 1 */
 		status = "disabled";
 	};

 	mpp@a100 { /* MPP 2 */
 	};

 	mpp@a200 { /* MPP 3 */
 	};

 	mpp@a300 { /* MPP 4 */
 	};

 	mpp@a400 { /* MPP 5 */
 		/* SPI_ETH config */
 		qcom,mode = <1>; /* DIG_OUT */
 		qcom,output-type = <0>; /* CMOS */
 		qcom,vin-sel = <2>; /* PM8941_S3 1.8V > 1.6V */
 		qcom,src-sel = <0>; /* CONSTANT */
 		qcom,master-en = <1>; /* ENABLE MPP */
 	};

 	mpp@a500 { /* MPP 6 */
 		/* SPI_ETH_RST config */
 		qcom,mode = <1>; /* DIG_OUT */
 		qcom,output-type = <0>; /* CMOS */
 		qcom,vin-sel = <2>; /* PM8941_S3 1.8V > 1.6V */
 		qcom,src-sel = <0>; /* CONSTANT */
 		qcom,master-en = <1>; /* ENABLE MPP */
 	};

 	mpp@a600 { /* MPP 7 */
 	};

 	mpp@a700 { /* MPP 8 */
 	};
 };

 &pm8841_mpps {

 	mpp@a000 { /* MPP 1 */
 	};

 	mpp@a100 { /* MPP 2 */
 	};

 	mpp@a200 { /* MPP 3 */
 	};

 	mpp@a300 { /* MPP 4 */
 	};
 };

 /* CoreSight */
 &tpiu {
 	qcom,seta-gpios = <&msmgpio 31 0>,
 			  <&msmgpio 32 0>,
 			  <&msmgpio 33 0>,
 			  <&msmgpio 34 0>,
 			  <&msmgpio 35 0>,
 			  <&msmgpio 36 0>,
 			  <&msmgpio 37 0>,
 			  <&msmgpio 38 0>,
 			  <&msmgpio 39 0>,
 			  <&msmgpio 40 0>,
 			  <&msmgpio 41 0>,
 			  <&msmgpio 42 0>,
 			  <&msmgpio 43 0>,
 			  <&msmgpio 44 0>,
 			  <&msmgpio 45 0>,
 			  <&msmgpio 46 0>,
 			  <&msmgpio 47 0>,
 			  <&msmgpio 48 0>;
 	qcom,seta-gpios-func = <4 4 4 3 4 4 4 3 4 3 5 5 5 5 4 4 5 5>;
 	qcom,seta-gpios-drv =  <7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7>;
 	qcom,seta-gpios-pull = <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
 	qcom,seta-gpios-dir =  <2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2>;

 	qcom,setb-gpios = <&msmgpio 15 0>,
 			  <&msmgpio 16 0>,
 			  <&msmgpio 17 0>,
 			  <&msmgpio 18 0>,
 			  <&msmgpio 19 0>,
 			  <&msmgpio 20 0>,
 			  <&msmgpio 21 0>,
 			  <&msmgpio 22 0>,
 			  <&msmgpio 23 0>,
 			  <&msmgpio 24 0>,
 			  <&msmgpio 25 0>,
 			  <&msmgpio 26 0>,
 			  <&msmgpio 27 0>,
 			  <&msmgpio 28 0>,
 			  <&msmgpio 89 0>,
 			  <&msmgpio 90 0>,
 			  <&msmgpio 91 0>,
 			  <&msmgpio 92 0>;
 	qcom,setb-gpios-func = <2 2 2 2 5 5 5 5 6 6 6 7 7 5 2 3 3 3>;
 	qcom,setb-gpios-drv =  <7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7>;
 	qcom,setb-gpios-pull = <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
 	qcom,setb-gpios-dir =  <2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2>;
 };

 &slim_msm {
 	taiko_codec {
 		qcom,cdc-micbias1-ext-cap;
 		qcom,cdc-micbias3-ext-cap;
 		qcom,cdc-micbias4-ext-cap;

 		/* If boot isn't available, vph_pwr_vreg can be used instead */
 		cdc-vdd-spkdrv-supply = <&pm8941_boost>;
 		qcom,cdc-vdd-spkdrv-voltage = <5000000 5000000>;
 		qcom,cdc-vdd-spkdrv-current = <1250000>;

 		qcom,cdc-on-demand-supplies = "cdc-vdd-spkdrv";
 	};
 };
	/* Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
	*
	* This program is free software; you can redistribute it and/or modify
	* it under the terms of the GNU General Public License version 2 and
	* only version 2 as published by the Free Software Foundation.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*/

	/include/ "dsi-panel-toshiba-720p-video.dtsi"
	/include/ "dsi-panel-orise-720p-video.dtsi"
	/include/ "msm8974-leds.dtsi"
	/include/ "msm8974-camera-sensor-cdp.dtsi"

	/ {
	serial@f991e000 {
	status = "ok";
	};

	qcom,mdss_dsi_toshiba_720p_video {
	status = "ok";
	qcom,cont-splash-enabled;
	};

	qcom,mdss_dsi_orise_720p_video {
	status = "disable";
	};

	qcom,hdmi_tx@fd922100 {
	status = "ok";
	};

	i2c@f9924000 {
	atmel_mxt_ts@4a {
	compatible = "atmel,mxt-ts";
	reg = <0x4a>;
	interrupt-parent = <&msmgpio>;
	interrupts = <61 0x2>;
	vdd_ana-supply = <&pm8941_l18>;
	vcc_i2c-supply = <&pm8941_lvs1>;
	atmel,reset-gpio = <&msmgpio 60 0x00>;
	atmel,irq-gpio = <&msmgpio 61 0x00>;
	atmel,panel-coords = <0 0 760 1424>;
	atmel,display-coords = <0 0 720 1280>;
	atmel,i2c-pull-up;
	atmel,no-force-update;
	atmel,cfg_1 {
	atmel,family-id = <0x82>;
	atmel,variant-id = <0x19>;
	atmel,version = <0x10>;
	atmel,build = <0xaa>;
	atmel,config = [
	/* Object 6, Instance = 0 */
	00 00 00 00 00 00
	/* Object 38, Instance = 0 */
	15 01 00 03 0A 0C 00 00
	/* Object 7, Instance = 0 */
	20 08 32 03
	/* Object 8, Instance = 0 */
	0F 00 0A 0A 00 00 0A 0A 00 00
	/* Object 9, Instance = 0 */
	83 00 00 18 0E 00 70 46 02 01
	00 0A 03 31 04 05 0A 0A 90 05
	F8 02 05 F1 F1 0F 00 00 08 2D
	12 06 00 00 00 01
	/* Object 15, Instance = 0 */
	00 00 00 00 00 00 00 00 00 00
	00
	/* Object 18, Instance = 0 */
	00 00
	/* Object 19, Instance = 0 */
	00 00 00 00 00 00
	/* Object 23, Instance = 0 */
	00 00 00 00 00 00 00 00 00 00
	00 00 00 00 00
	/* Object 25, Instance = 0 */
	00 00 00 00 00 00 00 00 00 00
	00 00 00 00 00
	/* Object 40, Instance = 0 */
	00 00 00 00 00
	/* Object 42, Instance = 0 */
	33 1E 19 10 80 00 00 00 FF 00
	/* Object 46, Instance = 0 */
	00 00 10 10 00 00 03 00 00 01
	/* Object 47, Instance = 0 */
	08 0A 28 0A 02 0A 00 8C 00 20
	00 00 00
	/* Object 55, Instance = 0 */
	00 00 00 00 00 00
	/* Object 56, Instance = 0 */
	00 00 00 18 05 05 05 05 05 05
	05 05 05 05 05 05 05 05 05 05
	05 05 05 05 05 05 05 05 00 00
	00 00 00 00 00 00 00 00 00 00
	00 00
	/* Object 57, Instance = 0 */
	00 00 00
	/* Object 61, Instance = 0 */
	00 00 00 00 00
	/* Object 62, Instance = 0 */
	01 2A 00 16 00 00 00 00 0B 01
	02 03 04 08 00 00 08 10 18 05
	00 0A 05 05 50 14 19 34 1A 7F
	00 00 00 00 00 00 00 00 00 30
	05 02 00 01 00 05 00 00 00 00
	00 00 00 00
	];
	};
	};
	};

	gen-vkeys {
	compatible = "qcom,gen-vkeys";
	label = "atmel_mxt_ts";
	qcom,disp-maxx = <720>;
	qcom,disp-maxy = <1280>;
	qcom,panel-maxx = <760>;
	qcom,panel-maxy = <1424>;
	qcom,key-codes = <158 139 102 217>;
	};

	i2c@f9967000 {
	isa1200@48 {
	status = "okay";
	reg = <0x48>;
	vcc_i2c-supply = <&pm8941_s3>;
	compatible = "imagis,isa1200";
	label = "vibrator";
	imagis,chip-en;
	imagis,smart-en;
	imagis,need-pwm-clk;
	imagis,ext-clk-en;
	imagis,hap-en-gpio = <&msmgpio 86 0x00>;
	imagis,max-timeout = <15000>;
	imagis,pwm-div = <256>;
	imagis,mode-ctrl = <2>;
	imagis,regulator {
	regulator-name = "vcc_i2c";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-max-microamp = <9360>;
	};
	};
	};

	gpio_keys {
	compatible = "gpio-keys";
	input-name = "gpio-keys";

	camera_snapshot {
	label = "camera_snapshot";
	gpios = <&pm8941_gpios 3 0x1>;
	linux,input-type = <1>;
	linux,code = <0x2fe>;
	gpio-key,wakeup;
	debounce-interval = <15>;
	};

	camera_focus {
	label = "camera_focus";
	gpios = <&pm8941_gpios 4 0x1>;
	linux,input-type = <1>;
	linux,code = <0x210>;
	gpio-key,wakeup;
	debounce-interval = <15>;
	};

	vol_up {
	label = "volume_up";
	gpios = <&pm8941_gpios 5 0x1>;
	linux,input-type = <1>;
	linux,code = <115>;
	gpio-key,wakeup;
	debounce-interval = <15>;
	};
	};

	spi@f9923000 {
	ethernet-switch@2 {
	compatible = "micrel,ks8851";
	reg = <2>;
	interrupt-parent = <&msmgpio>;
	interrupts = <94 0>;
	spi-max-frequency = <4800000>;
	rst-gpio = <&pm8941_mpps 6 0>;
	vdd-io-supply = <&spi_eth_vreg>;
	vdd-phy-supply = <&spi_eth_vreg>;
	};
	};

	sound {
	qcom,model = "msm8974-taiko-cdp-snd-card";
	qcom,hdmi-audio-rx;
	qcom,us-euro-gpios = <&pm8941_gpios 20 0>;
	};

	usb2_otg_sw: regulator-tpd4s214 {
	compatible = "regulator-fixed";
	regulator-name = "usb2_otg_sw";
	gpio = <&pm8941_gpios 18 0>;
	parent-supply = <&pm8941_boost>;
	startup-delay-us = <17000>;
	enable-active-high;
	};

	hsic_host: hsic@f9a00000 {
	compatible = "qcom,hsic-host";
	reg = <0xf9a00000 0x400>;
	#address-cells = <0>;
	interrupt-parent = <&hsic_host>;
	interrupts = <0 1 2>;
	#interrupt-cells = <1>;
	interrupt-map-mask = <0xffffffff>;
	interrupt-map = <0 &intc 0 136 0
	1 &intc 0 148 0
	2 &msmgpio 144 0x8>;
	interrupt-names = "core_irq", "async_irq", "wakeup";
	HSIC_VDDCX-supply = <&pm8841_s2>;
	HSIC_GDSC-supply = <&gdsc_usb_hsic>;
	hsic,strobe-gpio = <&msmgpio 144 0x00>;
	hsic,data-gpio = <&msmgpio 145 0x00>;
	hsic,resume-gpio = <&msmgpio 80 0x00>;
	hsic,ignore-cal-pad-config;
	hsic,strobe-pad-offset = <0x2050>;
	hsic,data-pad-offset = <0x2054>;

	qcom,msm-bus,name = "hsic";
	qcom,msm-bus,num-cases = <2>;
	qcom,msm-bus,num-paths = <1>;
	qcom,msm-bus,vectors-KBps =
	<85 512 0 0>,
	<85 512 40000 160000>;
	};

	wlan0: qca,wlan {
	compatible = "qca,ar6004-hsic";
	qcom,msm-bus,name = "wlan";
	qcom,msm-bus,num-cases = <5>;
	qcom,msm-bus,active-only = <0>;
	qcom,msm-bus,num-paths = <1>;
	qcom,msm-bus,vectors-KBps =
	<85 512 0 0>,
	<85 512 40000 160000>,
	<85 512 40000 320000>,
	<85 512 40000 480000>,
	<85 512 40000 640000>;
	};
	};

	&spmi_bus {
	qcom,pm8941@1 {
	qcom,leds@d800 {
	status = "okay";
	qcom,wled_0 {
	label = "wled";
	linux,name = "wled:backlight";
	linux,default-trigger = "bkl-trigger";
	qcom,cs-out-en;
	qcom,op-fdbck = <1>;
	qcom,default-state = "on";
	qcom,max-current = <25>;
	qcom,ctrl-delay-us = <0>;
	qcom,boost-curr-lim = <3>;
	qcom,cp-sel = <0>;
	qcom,switch-freq = <2>;
	qcom,ovp-val = <2>;
	qcom,num-strings = <1>;
	qcom,id = <0>;
	};
	};

	qcom,leds@d900 {
	status = "disabled";
	};

	qcom,leds@da00 {
	status = "disabled";
	};

	qcom,leds@db00 {
	status = "disabled";
	};

	qcom,leds@dc00 {
	status = "disabled";
	};

	qcom,leds@dd00 {
	status = "disabled";
	};

	qcom,leds@de00 {
	status = "disabled";
	};

	qcom,leds@df00 {
	status = "disabled";
	};

	qcom,leds@e000 {
	status = "disabled";
	};

	qcom,leds@e100 {
	status = "disabled";
	};
	};
	};

	&sdcc1 {
	status = "disabled";
	};

	&sdcc2 {
	#address-cells = <0>;
	interrupt-parent = <&sdcc2>;
	interrupts = <0 1 2>;
	#interrupt-cells = <1>;
	interrupt-map-mask = <0xffffffff>;
	interrupt-map = <0 &intc 0 125 0
	1 &intc 0 220 0
	2 &msmgpio 62 0x3>;
	interrupt-names = "core_irq", "bam_irq", "status_irq";
	cd-gpios = <&msmgpio 62 0x1>;
	wp-gpios = <&pm8941_gpios 29 0x1>;
	status = "disabled";
	};

	&sdhc_1 {
	vdd-supply = <&pm8941_l20>;
	vdd-io-supply = <&pm8941_s3>;

	qcom,vdd-always-on;
	qcom,vdd-lpm-sup;
	qcom,vdd-voltage-level = <2950000 2950000>;
	qcom,vdd-current-level = <800 500000>;

	qcom,vdd-io-always-on;
	qcom,vdd-io-voltage-level = <1800000 1800000>;
	qcom,vdd-io-current-level = <250 154000>;

	qcom,pad-pull-on = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
	qcom,pad-pull-off = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
	qcom,pad-drv-on = <0x4 0x4 0x4>; /* 10mA, 10mA, 10mA */
	qcom,pad-drv-off = <0x0 0x0 0x0>; /* 2mA, 2mA, 2mA */

	qcom,nonremovable;
	status = "ok";
	};

	&sdhc_2 {
	#address-cells = <0>;
	interrupt-parent = <&sdhc_2>;
	interrupts = <0 1 2>;
	#interrupt-cells = <1>;
	interrupt-map-mask = <0xffffffff>;
	interrupt-map = <0 &intc 0 125 0
	1 &intc 0 221 0
	2 &msmgpio 62 0x3>;
	interrupt-names = "hc_irq", "pwr_irq", "status_irq";
	cd-gpios = <&msmgpio 62 0x1>;

	vdd-supply = <&pm8941_l21>;
	vdd-io-supply = <&pm8941_l13>;

	qcom,vdd-voltage-level = <2950000 2950000>;
	qcom,vdd-current-level = <9000 800000>;

	qcom,vdd-io-voltage-level = <1800000 2950000>;
	qcom,vdd-io-current-level = <6 22000>;

	qcom,pad-pull-on = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
	qcom,pad-pull-off = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */
	qcom,pad-drv-on = <0x4 0x4 0x4>; /* 10mA, 10mA, 10mA */
	qcom,pad-drv-off = <0x0 0x0 0x0>; /* 2mA, 2mA, 2mA */
	status = "ok";
	};

	/* Drive strength recommendations for clock line from hardware team is 10 mA.
	* But since the driver has been been using the below values from the start
	* without any problems, continue to use those.
	*/
	&sdcc1 {
	qcom,pad-drv-on = <0x7 0x4 0x4>; /* 16mA, 10mA, 10mA */
	};

	&sdcc2 {
	qcom,pad-drv-on = <0x7 0x4 0x4>; /* 16mA, 10mA, 10mA */
	};

	&sdhc_1 {
	qcom,pad-drv-on = <0x7 0x4 0x4>; /* 16mA, 10mA, 10mA */
	};

	&sdhc_2 {
	qcom,pad-drv-on = <0x7 0x4 0x4>; /* 16mA, 10mA, 10mA */
	};

	&uart7 {
	status = "ok";
	qcom,tx-gpio = <&msmgpio 41 0x00>;
	qcom,rx-gpio = <&msmgpio 42 0x00>;
	qcom,cts-gpio = <&msmgpio 43 0x00>;
	qcom,rfr-gpio = <&msmgpio 44 0x00>;
	};

	&usb3 {
	qcom,otg-capability;
	};

	&pm8941_chg {
	status = "ok";

	qcom,chgr@1000 {
	status = "ok";
	};

	qcom,buck@1100 {
	status = "ok";
	};

	qcom,usb-chgpth@1300 {
	status = "ok";
	};

	qcom,dc-chgpth@1400 {
	status = "ok";
	};

	qcom,boost@1500 {
	status = "ok";
	};

	qcom,chg-misc@1600 {
	status = "ok";
	};
	};

	&pm8941_gpios {
	gpio@c000 { /* GPIO 1 */
	};

	gpio@c100 { /* GPIO 2 */
	};

	gpio@c200 { /* GPIO 3 */
	qcom,mode = <0>;
	qcom,pull = <0>;
	qcom,vin-sel = <2>;
	qcom,src-sel = <0>;
	};

	gpio@c300 { /* GPIO 4 */
	qcom,mode = <0>;
	qcom,pull = <0>;
	qcom,vin-sel = <2>;
	qcom,src-sel = <0>;
	};

	gpio@c400 { /* GPIO 5 */
	qcom,mode = <0>;
	qcom,pull = <0>;
	qcom,vin-sel = <2>;
	qcom,src-sel = <0>;
	};

	gpio@c500 { /* GPIO 6 */
	};

	gpio@c600 { /* GPIO 7 */
	};

	gpio@c700 { /* GPIO 8 */
	};

	gpio@c800 { /* GPIO 9 */
	};

	gpio@c900 { /* GPIO 10 */
	};

	gpio@ca00 { /* GPIO 11 */
	};

	gpio@cb00 { /* GPIO 12 */
	};

	gpio@cc00 { /* GPIO 13 */
	};

	gpio@cd00 { /* GPIO 14 */
	};

	gpio@ce00 { /* GPIO 15 */
	qcom,mode = <1>;
	qcom,output-type = <0>;
	qcom,pull = <5>;
	qcom,vin-sel = <2>;
	qcom,out-strength = <3>;
	qcom,src-sel = <2>;
	qcom,master-en = <1>;
	};

	gpio@cf00 { /* GPIO 16 */
	qcom,mode = <1>;
	qcom,output-type = <0>;
	qcom,pull = <2>;
	qcom,vin-sel = <2>;
	qcom,out-strength = <2>;
	qcom,src-sel = <2>;
	qcom,master-en = <1>;
	};

	gpio@d000 { /* GPIO 17 */
	};

	gpio@d100 { /* GPIO 18 */
	/* usb2_otg_sw regulator enable */
	qcom,mode = <1>; /* Digital output */
	qcom,output-type = <0>; /* CMOS logic */
	qcom,invert = <0>; /* Output low initially */
	qcom,vin-sel = <2>; /* PM8941 S3 = 1.8 V */
	qcom,src-sel = <0>; /* Constant */
	qcom,out-strength = <2>; /* Medium drive strength */
	qcom,master-en = <1>; /* Enable GPIO */
	};

	gpio@d200 { /* GPIO 19 */
	qcom,mode = <1>; /* QPNP_PIN_MODE_DIG_OUT */
	qcom,output-type = <0>; /* QPNP_PIN_OUT_BUF_CMOS */
	qcom,pull = <5>; /* QPNP_PIN_PULL_NO */
	qcom,vin-sel = <2>; /* QPNP_PIN_VIN2 */
	qcom,out-strength = <2>; /* QPNP_PIN_OUT_STRENGTH_MED */
	qcom,src-sel = <0>; /* QPNP_PIN_SEL_FUNC_CONSTANT */
	qcom,master-en = <1>;
	};

	gpio@d300 { /* GPIO 20 */
	qcom,mode = <1>; /* QPNP_PIN_MODE_DIG_OUT */
	qcom,output-type = <0>; /* QPNP_PIN_OUT_BUF_CMOS */
	qcom,invert = <0>; /* Output low initially */
	qcom,pull = <5>; /* QPNP_PIN_PULL_NO */
	qcom,vin-sel = <2>; /* QPNP_PIN_VIN2 */
	qcom,out-strength = <2>; /* QPNP_PIN_OUT_STRENGTH_MED */
	qcom,src-sel = <0>; /* QPNP_PIN_SEL_FUNC_CONSTANT */
	qcom,master-en = <1>;
	};

	gpio@d400 { /* GPIO 21 */
	};

	gpio@d500 { /* GPIO 22 */
	};

	gpio@d600 { /* GPIO 23 */
	};

	gpio@d700 { /* GPIO 24 */
	};

	gpio@d800 { /* GPIO 25 */
	};

	gpio@d900 { /* GPIO 26 */
	};

	gpio@da00 { /* GPIO 27 */
	};

	gpio@db00 { /* GPIO 28 */
	};

	gpio@dc00 { /* GPIO 29 */
	qcom,pull = <0>; /* set to default pull */
	qcom,master-en = <1>;
	qcom,vin-sel = <2>; /* select 1.8 V source */
	};

	gpio@dd00 { /* GPIO 30 */
	};

	gpio@de00 { /* GPIO 31 */
	};

	gpio@df00 { /* GPIO 32 */
	};

	gpio@e000 { /* GPIO 33 */
	};

	gpio@e100 { /* GPIO 34 */
	};

	gpio@e200 { /* GPIO 35 */
	};

	gpio@e300 { /* GPIO 36 */
	};
	};

	&pm8941_mpps {

	mpp@a000 { /* MPP 1 */
	status = "disabled";
	};

	mpp@a100 { /* MPP 2 */
	};

	mpp@a200 { /* MPP 3 */
	};

	mpp@a300 { /* MPP 4 */
	};

	mpp@a400 { /* MPP 5 */
	/* SPI_ETH config */
	qcom,mode = <1>; /* DIG_OUT */
	qcom,output-type = <0>; /* CMOS */
	qcom,vin-sel = <2>; /* PM8941_S3 1.8V > 1.6V */
	qcom,src-sel = <0>; /* CONSTANT */
	qcom,master-en = <1>; /* ENABLE MPP */
	};

	mpp@a500 { /* MPP 6 */
	/* SPI_ETH_RST config */
	qcom,mode = <1>; /* DIG_OUT */
	qcom,output-type = <0>; /* CMOS */
	qcom,vin-sel = <2>; /* PM8941_S3 1.8V > 1.6V */
	qcom,src-sel = <0>; /* CONSTANT */
	qcom,master-en = <1>; /* ENABLE MPP */
	};

	mpp@a600 { /* MPP 7 */
	};

	mpp@a700 { /* MPP 8 */
	};
	};

	&pm8841_mpps {

	mpp@a000 { /* MPP 1 */
	};

	mpp@a100 { /* MPP 2 */
	};

	mpp@a200 { /* MPP 3 */
	};

	mpp@a300 { /* MPP 4 */
	};
	};

	/* CoreSight */
	&tpiu {
	qcom,seta-gpios = <&msmgpio 31 0>,
	<&msmgpio 32 0>,
	<&msmgpio 33 0>,
	<&msmgpio 34 0>,
	<&msmgpio 35 0>,
	<&msmgpio 36 0>,
	<&msmgpio 37 0>,
	<&msmgpio 38 0>,
	<&msmgpio 39 0>,
	<&msmgpio 40 0>,
	<&msmgpio 41 0>,
	<&msmgpio 42 0>,
	<&msmgpio 43 0>,
	<&msmgpio 44 0>,
	<&msmgpio 45 0>,
	<&msmgpio 46 0>,
	<&msmgpio 47 0>,
	<&msmgpio 48 0>;
	qcom,seta-gpios-func = <4 4 4 3 4 4 4 3 4 3 5 5 5 5 4 4 5 5>;
	qcom,seta-gpios-drv = <7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7>;
	qcom,seta-gpios-pull = <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
	qcom,seta-gpios-dir = <2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2>;

	qcom,setb-gpios = <&msmgpio 15 0>,
	<&msmgpio 16 0>,
	<&msmgpio 17 0>,
	<&msmgpio 18 0>,
	<&msmgpio 19 0>,
	<&msmgpio 20 0>,
	<&msmgpio 21 0>,
	<&msmgpio 22 0>,
	<&msmgpio 23 0>,
	<&msmgpio 24 0>,
	<&msmgpio 25 0>,
	<&msmgpio 26 0>,
	<&msmgpio 27 0>,
	<&msmgpio 28 0>,
	<&msmgpio 89 0>,
	<&msmgpio 90 0>,
	<&msmgpio 91 0>,
	<&msmgpio 92 0>;
	qcom,setb-gpios-func = <2 2 2 2 5 5 5 5 6 6 6 7 7 5 2 3 3 3>;
	qcom,setb-gpios-drv = <7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7>;
	qcom,setb-gpios-pull = <0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0>;
	qcom,setb-gpios-dir = <2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2>;
	};

	&slim_msm {
	taiko_codec {
	qcom,cdc-micbias1-ext-cap;
	qcom,cdc-micbias3-ext-cap;
	qcom,cdc-micbias4-ext-cap;

	/* If boot isn't available, vph_pwr_vreg can be used instead */
	cdc-vdd-spkdrv-supply = <&pm8941_boost>;
	qcom,cdc-vdd-spkdrv-voltage = <5000000 5000000>;
	qcom,cdc-vdd-spkdrv-current = <1250000>;

	qcom,cdc-on-demand-supplies = "cdc-vdd-spkdrv";
	};
	};