mmc: mxs-mmc: fix clock rate setting
commit d982dcdc4e64eb1881df44b0035a8268bf1ab067 upstream.
Fix clock rate setting in the mxs-mmc driver. Previously, if div2 was 0
then the value for TIMING_CLOCK_RATE would have been 255 instead of 0.
The limits for div1 (TIMING_CLOCK_DIVIDE) and div2 (TIMING_CLOCK_RATE+1)
were also not correctly defined.
Can easily be reproduced on mx23evk: default clock for high speed sdio
cards is 50 MHz. With a SSP_CLK of 28.8 MHz default), this resulted in
an actual clock rate of about 56 kHz. Tested on mx23evk.
Signed-off-by: Koen Beel <koen.beel@barco.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/drivers/mmc/host/mxs-mmc.c b/drivers/mmc/host/mxs-mmc.c
index 99d39a6..d513d47 100644
--- a/drivers/mmc/host/mxs-mmc.c
+++ b/drivers/mmc/host/mxs-mmc.c
@@ -564,40 +564,38 @@
static void mxs_mmc_set_clk_rate(struct mxs_mmc_host *host, unsigned int rate)
{
- unsigned int ssp_rate, bit_rate;
- u32 div1, div2;
+ unsigned int ssp_clk, ssp_sck;
+ u32 clock_divide, clock_rate;
u32 val;
- ssp_rate = clk_get_rate(host->clk);
+ ssp_clk = clk_get_rate(host->clk);
- for (div1 = 2; div1 < 254; div1 += 2) {
- div2 = ssp_rate / rate / div1;
- if (div2 < 0x100)
+ for (clock_divide = 2; clock_divide <= 254; clock_divide += 2) {
+ clock_rate = DIV_ROUND_UP(ssp_clk, rate * clock_divide);
+ clock_rate = (clock_rate > 0) ? clock_rate - 1 : 0;
+ if (clock_rate <= 255)
break;
}
- if (div1 >= 254) {
+ if (clock_divide > 254) {
dev_err(mmc_dev(host->mmc),
"%s: cannot set clock to %d\n", __func__, rate);
return;
}
- if (div2 == 0)
- bit_rate = ssp_rate / div1;
- else
- bit_rate = ssp_rate / div1 / div2;
+ ssp_sck = ssp_clk / clock_divide / (1 + clock_rate);
val = readl(host->base + HW_SSP_TIMING);
val &= ~(BM_SSP_TIMING_CLOCK_DIVIDE | BM_SSP_TIMING_CLOCK_RATE);
- val |= BF_SSP(div1, TIMING_CLOCK_DIVIDE);
- val |= BF_SSP(div2 - 1, TIMING_CLOCK_RATE);
+ val |= BF_SSP(clock_divide, TIMING_CLOCK_DIVIDE);
+ val |= BF_SSP(clock_rate, TIMING_CLOCK_RATE);
writel(val, host->base + HW_SSP_TIMING);
- host->clk_rate = bit_rate;
+ host->clk_rate = ssp_sck;
dev_dbg(mmc_dev(host->mmc),
- "%s: div1 %d, div2 %d, ssp %d, bit %d, rate %d\n",
- __func__, div1, div2, ssp_rate, bit_rate, rate);
+ "%s: clock_divide %d, clock_rate %d, ssp_clk %d, rate_actual %d, rate_requested %d\n",
+ __func__, clock_divide, clock_rate, ssp_clk, ssp_sck, rate);
}
static void mxs_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)