| /* Copyright (c) 2013, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| /include/ "dsi-panel-sharp-qhd-video.dtsi" |
| /include/ "msm8974-camera-sensor-dragonboard.dtsi" |
| /include/ "msm8974-leds.dtsi" |
| |
| &vph_pwr_vreg { |
| status = "ok"; |
| }; |
| |
| &soc { |
| serial@f991e000 { |
| status = "ok"; |
| }; |
| |
| qcom,mdss_dsi_sharp_qhd_video { |
| status = "ok"; |
| qcom,cont-splash-enabled; |
| }; |
| |
| qcom,hdmi_tx@fd922100 { |
| status = "ok"; |
| }; |
| |
| gpio_keys { |
| compatible = "gpio-keys"; |
| input-name = "gpio-keys"; |
| |
| vol_up { |
| label = "volume_up"; |
| gpios = <&pm8941_gpios 5 0x1>; |
| linux,input-type = <1>; |
| linux,code = <115>; |
| gpio-key,wakeup; |
| debounce-interval = <15>; |
| }; |
| |
| general { |
| label = "general"; |
| gpios = <&pm8941_gpios 23 0x1>; |
| linux,input-type = <1>; |
| linux,code = <102>; |
| gpio-key,wakeup; |
| debounce-interval = <15>; |
| }; |
| }; |
| |
| bt_ar3002 { |
| compatible = "qca,ar3002"; |
| qca,bt-reset-gpio = <&pm8941_gpios 34 0>; |
| }; |
| |
| hsic_hub { |
| compatible = "qcom,hsic-smsc-hub"; |
| smsc,model-id = <4604>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| smsc,reset-gpio = <&pm8941_gpios 8 0x00>; |
| /* Dragonboard has an always-on VBUS supply for HSIC hub, |
| * providing a dummy regulator for the hub driver |
| */ |
| hub_vbus-supply = <&vph_pwr_vreg>; |
| |
| hsic_host: hsic@f9a00000 { |
| compatible = "qcom,hsic-host"; |
| reg = <0xf9a00000 0x400>; |
| #address-cells = <0>; |
| interrupt-parent = <&hsic_host>; |
| interrupts = <0 1 2>; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0xffffffff>; |
| interrupt-map = <0 &intc 0 136 0 |
| 1 &intc 0 148 0 |
| 2 &msmgpio 144 0x8>; |
| interrupt-names = "core_irq", "async_irq", "wakeup"; |
| HSIC_VDDCX-supply = <&pm8841_s2>; |
| HSIC_GDSC-supply = <&gdsc_usb_hsic>; |
| hsic,strobe-gpio = <&msmgpio 144 0x00>; |
| hsic,data-gpio = <&msmgpio 145 0x00>; |
| hsic,ignore-cal-pad-config; |
| hsic,strobe-pad-offset = <0x2050>; |
| hsic,data-pad-offset = <0x2054>; |
| qcom,phy-susp-sof-workaround; |
| |
| qcom,msm-bus,name = "hsic"; |
| qcom,msm-bus,num-cases = <2>; |
| qcom,msm-bus,active-only = <0>; |
| qcom,msm-bus,num-paths = <1>; |
| qcom,msm-bus,vectors-KBps = |
| <85 512 0 0>, |
| <85 512 40000 160000>; |
| }; |
| }; |
| |
| i2c@f9923000 { |
| status = "ok"; |
| atmel_mxt_ts@4a { |
| compatible = "atmel,mxt-ts"; |
| reg = <0x4a>; |
| interrupt-parent = <&msmgpio>; |
| interrupts = <61 0x2>; |
| vdd_ana-supply = <&pm8941_l18>; |
| vcc_i2c-supply = <&pm8941_s3>; |
| atmel,reset-gpio = <&msmgpio 60 0x00>; |
| atmel,irq-gpio = <&msmgpio 61 0x00>; |
| atmel,panel-coords = <0 0 566 1067>; |
| atmel,display-coords = <0 0 540 960>; |
| atmel,i2c-pull-up; |
| atmel,cfg_1 { |
| atmel,family-id = <0x81>; |
| atmel,variant-id = <0x19>; |
| atmel,version = <0x10>; |
| atmel,build = <0xaa>; |
| atmel,config = [ |
| /* Object 38, Instance = 0 */ |
| 0F 02 00 17 04 0C 00 00 |
| /* Object 7, Instance = 0 */ |
| 30 FF 19 |
| /* Object 8, Instance = 0 */ |
| 1B 00 05 01 00 00 08 08 00 00 |
| /* Object 9, Instance = 0 */ |
| 83 00 00 13 0B 00 10 23 01 03 |
| 0A 0F 01 0B 04 05 28 0A 2B 04 |
| 36 02 00 00 00 00 8F 28 8F 50 |
| 12 0F 32 32 02 |
| /* Object 15, Instance = 0 */ |
| 00 00 00 00 00 00 00 00 00 00 |
| 00 |
| /* Object 18, Instance = 0 */ |
| 00 00 |
| /* Object 19, Instance = 0 */ |
| 00 00 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 |
| /* Object 23, Instance = 0 */ |
| 00 00 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 |
| /* Object 25, Instance = 0 */ |
| 00 00 00 00 00 00 00 00 00 00 |
| 00 00 00 00 |
| /* Object 40, Instance = 0 */ |
| 00 00 00 00 00 |
| /* Object 42, Instance = 0 */ |
| 00 00 00 00 00 00 00 00 |
| /* Object 46, Instance = 0 */ |
| 00 03 10 30 00 00 01 00 00 |
| /* Object 47, Instance = 0 */ |
| 00 00 00 00 00 00 00 00 00 00 |
| /* Object 48, Instance = 0 */ |
| 00 00 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 00 00 |
| 00 00 00 00 00 00 00 00 00 00 |
| 00 00 00 00 |
| ]; |
| }; |
| }; |
| }; |
| |
| gen-vkeys { |
| compatible = "qcom,gen-vkeys"; |
| label = "atmel_mxt_ts"; |
| qcom,disp-maxx = <540>; |
| qcom,disp-maxy = <960>; |
| qcom,panel-maxx = <566>; |
| qcom,panel-maxy = <1067>; |
| qcom,key-codes = <158 139 102 217>; |
| }; |
| |
| sound { |
| qcom,model = "apq8074-taiko-db-snd-card"; |
| qcom,hdmi-audio-rx; |
| |
| qcom,audio-routing = |
| "RX_BIAS", "MCLK", |
| "LDO_H", "MCLK", |
| "AMIC1", "MIC BIAS1 External", |
| "MIC BIAS1 External", "Analog Mic4", |
| "AMIC2", "MIC BIAS2 External", |
| "MIC BIAS2 External", "Headset Mic", |
| "AMIC3", "MIC BIAS2 External", |
| "MIC BIAS2 External", "ANCRight Headset Mic", |
| "AMIC4", "MIC BIAS2 External", |
| "MIC BIAS2 External", "ANCLeft Headset Mic", |
| "AMIC5", "MIC BIAS4 External", |
| "MIC BIAS4 External", "Analog Mic6", |
| "AMIC6", "MIC BIAS3 External", |
| "MIC BIAS3 External", "Analog Mic7", |
| "DMIC1", "MIC BIAS3 External", |
| "MIC BIAS3 External", "Digital Mic1", |
| "DMIC2", "MIC BIAS3 External", |
| "MIC BIAS3 External", "Digital Mic2", |
| "DMIC3", "MIC BIAS4 External", |
| "MIC BIAS4 External", "Digital Mic3", |
| "DMIC4", "MIC BIAS3 External", |
| "MIC BIAS3 External", "Digital Mic4", |
| "DMIC5", "MIC BIAS4 External", |
| "MIC BIAS4 External", "Digital Mic5", |
| "DMIC6", "MIC BIAS4 External", |
| "MIC BIAS4 External", "Digital Mic6"; |
| |
| |
| qcom,prim-auxpcm-gpio-clk = <&msmgpio 74 0>; |
| qcom,prim-auxpcm-gpio-sync = <&msmgpio 75 0>; |
| qcom,prim-auxpcm-gpio-din = <&msmgpio 76 0>; |
| qcom,prim-auxpcm-gpio-dout = <&msmgpio 77 0>; |
| qcom,prim-auxpcm-gpio-set = "prim-gpio-tert"; |
| |
| qcom,cdc-micbias2-headset-only; |
| }; |
| |
| qcom,pronto@fb21b000 { |
| status = "disabled"; |
| }; |
| |
| qcom,iris-fm { |
| status = "disabled"; |
| }; |
| |
| qcom,wcnss-wlan@fb000000 { |
| status = "disabled"; |
| }; |
| |
| qcom,smd-wcnss { |
| status = "disabled"; |
| }; |
| |
| qcom,smsm-wcnss { |
| status = "disabled"; |
| }; |
| }; |
| |
| &mdss_fb0 { |
| qcom,memory-reservation-size = <0x1000000>; /* size 16MB */ |
| }; |
| |
| &sdcc3 { |
| qcom,sup-voltages = <2000 2000>; |
| status = "ok"; |
| }; |
| |
| &pm8941_l19 { |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| qcom,init-voltage = <3300000>; |
| regulator-always-on; |
| }; |
| |
| &pm8941_l10 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| qcom,init-voltage = <1800000>; |
| regulator-always-on; |
| }; |
| |
| &uart7 { |
| status = "ok"; |
| qcom,tx-gpio = <&msmgpio 41 0x00>; |
| qcom,rx-gpio = <&msmgpio 42 0x00>; |
| qcom,cts-gpio = <&msmgpio 43 0x00>; |
| qcom,rfr-gpio = <&msmgpio 44 0x00>; |
| }; |
| |
| &usb_otg { |
| status = "ok"; |
| qcom,hsusb-otg-otg-control = <2>; |
| qcom,hsusb-otg-mode = <3>; |
| vbus_otg-supply = <&pm8941_mvs1>; |
| qcom,usb2-enable-hsphy2; |
| qcom,dp-manual-pullup; |
| |
| #address-cells = <0>; |
| interrupt-parent = <&usb_otg>; |
| interrupts = <0 1 2>; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0xffffffff>; |
| interrupt-map = <0 &intc 0 134 0 |
| 1 &intc 0 140 0 |
| 2 &spmi_bus 0x0 0x0 0x9 0x0>; |
| interrupt-names = "core_irq", "async_irq", "pmic_id_irq"; |
| }; |
| |
| &usb3 { |
| interrupts = <0>; /* remove pmic_id_irq; used by &usb_otg */ |
| qcom,charging-disabled; |
| vbus_dwc3-supply = <0>; |
| dwc3@f9200000 { |
| host-only-mode; |
| }; |
| }; |
| |
| &slim_msm { |
| taiko_codec { |
| qcom,cdc-micbias1-ext-cap; |
| qcom,cdc-micbias2-ext-cap; |
| qcom,cdc-micbias3-ext-cap; |
| qcom,cdc-micbias4-ext-cap; |
| |
| /* If boot isn't available, vph_pwr_vreg can be used instead */ |
| cdc-vdd-spkdrv-supply = <&pm8941_boost>; |
| qcom,cdc-vdd-spkdrv-voltage = <5000000 5000000>; |
| qcom,cdc-vdd-spkdrv-current = <1250000>; |
| |
| qcom,cdc-on-demand-supplies = "cdc-vdd-spkdrv"; |
| }; |
| }; |
| |
| &pm8941_gpios { |
| gpio@c000 { /* GPIO 1 */ |
| qcom,mode = <0>; |
| qcom,pull = <0>; |
| qcom,vin-sel = <2>; |
| qcom,src-sel = <0>; |
| }; |
| |
| gpio@c100 { /* GPIO 2 */ |
| qcom,mode = <0>; |
| qcom,pull = <0>; |
| qcom,vin-sel = <2>; |
| qcom,src-sel = <0>; |
| }; |
| |
| gpio@c200 { /* GPIO 3 */ |
| }; |
| |
| gpio@c300 { /* GPIO 4 */ |
| }; |
| |
| gpio@c400 { /* GPIO 5 */ |
| qcom,mode = <0>; |
| qcom,pull = <0>; |
| qcom,vin-sel = <2>; |
| qcom,src-sel = <0>; |
| }; |
| |
| gpio@c500 { /* GPIO 6 */ |
| /* TUSB3_HUB-RESET */ |
| qcom,mode = <1>; /* QPNP_PIN_MODE_DIG_OUT */ |
| qcom,output-type = <0>; /* QPNP_PIN_OUT_BUF_CMOS */ |
| qcom,pull = <0>; /* QPNP_PIN_PULL_30 */ |
| qcom,vin-sel = <0>; /* QPNP_PIN_VIN0 VPH */ |
| qcom,out-strength = <2>; /* QPNP_PIN_OUT_STRENGTH_MED */ |
| qcom,src-sel = <0>; /* QPNP_PIN_SEL_FUNC_CONSTANT */ |
| qcom,invert = <1>; /* Keep it out of reset */ |
| qcom,master-en = <1>; |
| }; |
| |
| gpio@c600 { /* GPIO 7 */ |
| }; |
| |
| gpio@c700 { /* GPIO 8 */ |
| /* HSIC_HUB-RESET */ |
| qcom,mode = <1>; /* DIG_OUT */ |
| qcom,pull = <5>; /* PULL_NO */ |
| qcom,out-strength = <2>; /* STRENGTH_MED */ |
| qcom,master-en = <1>; |
| }; |
| |
| gpio@c800 { /* GPIO 9 */ |
| /* GbE_RST_N */ |
| qcom,mode = <1>; /* QPNP_PIN_MODE_DIG_OUT */ |
| qcom,output-type = <0>; /* QPNP_PIN_OUT_BUF_CMOS */ |
| qcom,pull = <0>; /* QPNP_PIN_PULL_30 */ |
| qcom,vin-sel = <0>; /* QPNP_PIN_VIN0 VPH */ |
| qcom,out-strength = <2>; /* QPNP_PIN_OUT_STRENGTH_MED */ |
| qcom,src-sel = <0>; /* QPNP_PIN_SEL_FUNC_CONSTANT */ |
| qcom,invert = <1>; /* Keep it out of reset */ |
| qcom,master-en = <1>; |
| }; |
| |
| gpio@c900 { /* GPIO 10 */ |
| /* SATA_RST_N */ |
| qcom,mode = <1>; /* QPNP_PIN_MODE_DIG_OUT */ |
| qcom,output-type = <0>; /* QPNP_PIN_OUT_BUF_CMOS */ |
| qcom,pull = <0>; /* QPNP_PIN_PULL_30 */ |
| qcom,vin-sel = <0>; /* QPNP_PIN_VIN0 VPH */ |
| qcom,out-strength = <2>; /* QPNP_PIN_OUT_STRENGTH_MED */ |
| qcom,src-sel = <0>; /* QPNP_PIN_SEL_FUNC_CONSTANT */ |
| qcom,invert = <1>; /* Keep it out of reset */ |
| qcom,master-en = <1>; |
| }; |
| |
| gpio@ca00 { /* GPIO 11 */ |
| }; |
| |
| gpio@cb00 { /* GPIO 12 */ |
| }; |
| |
| gpio@cc00 { /* GPIO 13 */ |
| }; |
| |
| gpio@cd00 { /* GPIO 14 */ |
| }; |
| |
| gpio@ce00 { /* GPIO 15 */ |
| qcom,mode = <1>; |
| qcom,output-type = <0>; |
| qcom,pull = <5>; |
| qcom,vin-sel = <2>; |
| qcom,out-strength = <3>; |
| qcom,src-sel = <2>; |
| qcom,master-en = <1>; |
| }; |
| |
| gpio@cf00 { /* GPIO 16 */ |
| }; |
| |
| gpio@d000 { /* GPIO 17 */ |
| }; |
| |
| gpio@d100 { /* GPIO 18 */ |
| }; |
| |
| gpio@d200 { /* GPIO 19 */ |
| qcom,mode = <1>; /* QPNP_PIN_MODE_DIG_OUT */ |
| qcom,output-type = <0>; /* QPNP_PIN_OUT_BUF_CMOS */ |
| qcom,pull = <5>; /* QPNP_PIN_PULL_NO */ |
| qcom,vin-sel = <2>; /* QPNP_PIN_VIN2 */ |
| qcom,out-strength = <2>; /* QPNP_PIN_OUT_STRENGTH_MED */ |
| qcom,src-sel = <0>; /* QPNP_PIN_SEL_FUNC_CONSTANT */ |
| qcom,master-en = <1>; |
| }; |
| |
| gpio@d300 { /* GPIO 20 */ |
| }; |
| |
| gpio@d400 { /* GPIO 21 */ |
| }; |
| |
| gpio@d500 { /* GPIO 22 */ |
| }; |
| |
| gpio@d600 { /* GPIO 23 */ |
| }; |
| |
| gpio@d700 { /* GPIO 24 */ |
| }; |
| |
| gpio@d800 { /* GPIO 25 */ |
| }; |
| |
| gpio@d900 { /* GPIO 26 */ |
| }; |
| |
| gpio@da00 { /* GPIO 27 */ |
| }; |
| |
| gpio@db00 { /* GPIO 28 */ |
| }; |
| |
| gpio@dc00 { /* GPIO 29 */ |
| qcom,pull = <0>; /* set to default pull */ |
| qcom,master-en = <1>; |
| qcom,vin-sel = <2>; /* select 1.8 V source */ |
| }; |
| |
| gpio@dd00 { /* GPIO 30 */ |
| }; |
| |
| gpio@de00 { /* GPIO 31 */ |
| }; |
| |
| gpio@df00 { /* GPIO 32 */ |
| }; |
| |
| gpio@e000 { /* GPIO 33 */ |
| qcom,mode = <1>; /* QPNP_PIN_MODE_DIG_OUT */ |
| qcom,output-type = <0>; /* QPNP_PIN_OUT_BUF_CMOS */ |
| qcom,pull = <5>; /* QPNP_PIN_PULL_NO */ |
| qcom,vin-sel = <2>; /* QPNP_PIN_VIN2 */ |
| qcom,out-strength = <2>; /* QPNP_PIN_OUT_STRENGTH_MED */ |
| qcom,src-sel = <0>; /* QPNP_PIN_SEL_FUNC_CONSTANT */ |
| qcom,invert = <1>; |
| qcom,master-en = <1>; |
| }; |
| |
| gpio@e100 { /* GPIO 34 */ |
| qcom,mode = <1>; /* QPNP_PIN_MODE_DIG_OUT */ |
| qcom,output-type = <0>; /* QPNP_PIN_OUT_BUF_CMOS */ |
| qcom,pull = <5>; /* QPNP_PIN_PULL_NO */ |
| qcom,vin-sel = <2>; /* QPNP_PIN_VIN2 */ |
| qcom,out-strength = <2>; /* QPNP_PIN_OUT_STRENGTH_MED */ |
| qcom,src-sel = <0>; /* QPNP_PIN_SEL_FUNC_CONSTANT */ |
| qcom,invert = <0>; |
| qcom,master-en = <1>; |
| }; |
| |
| gpio@e200 { /* GPIO 35 */ |
| }; |
| |
| gpio@e300 { /* GPIO 36 */ |
| qcom,mode = <1>; /* QPNP_PIN_MODE_DIG_OUT */ |
| qcom,output-type = <0>; /* QPNP_PIN_OUT_BUF_CMOS */ |
| qcom,pull = <5>; /* QPNP_PIN_PULL_NO */ |
| qcom,vin-sel = <2>; /* QPNP_PIN_VIN2 */ |
| qcom,out-strength = <3>; /* QPNP_PIN_OUT_STRENGTH_HIGH */ |
| qcom,src-sel = <3>; /* QPNP_PIN_SEL_FUNC_2 */ |
| qcom,master-en = <1>; |
| }; |
| }; |
| |
| &pm8941_mpps { |
| |
| mpp@a000 { /* MPP 1 */ |
| status = "disabled"; |
| }; |
| |
| mpp@a100 { /* MPP 2 */ |
| }; |
| |
| mpp@a200 { /* MPP 3 */ |
| }; |
| |
| mpp@a300 { /* MPP 4 */ |
| }; |
| |
| mpp@a400 { /* MPP 5 */ |
| }; |
| |
| mpp@a500 { /* MPP 6 */ |
| }; |
| |
| mpp@a600 { /* MPP 7 */ |
| }; |
| |
| mpp@a700 { /* MPP 8 */ |
| }; |
| }; |
| |
| &pm8841_mpps { |
| |
| mpp@a000 { /* MPP 1 */ |
| }; |
| |
| mpp@a100 { /* MPP 2 */ |
| }; |
| |
| mpp@a200 { /* MPP 3*/ |
| }; |
| |
| mpp@a300 { /* MPP 4*/ |
| }; |
| }; |
| |
| &spi_epm { |
| status = "disabled"; |
| }; |
| |
| &pm8941_lsid1 { |
| qcom,leds@d000 { |
| qcom,rgb_2 { |
| status = "ok"; |
| qcom,default-state = "on"; |
| qcom,turn-off-delay-ms = <1000>; |
| }; |
| }; |
| |
| qcom,leds@d800 { |
| status = "okay"; |
| qcom,wled_0 { |
| label = "wled"; |
| linux,name = "wled:backlight"; |
| linux,default-trigger = "bkl-trigger"; |
| qcom,cs-out-en; |
| qcom,op-fdbck = <1>; |
| qcom,default-state = "on"; |
| qcom,max-current = <20>; |
| qcom,ctrl-delay-us = <0>; |
| qcom,boost-curr-lim = <3>; |
| qcom,cp-sel = <0>; |
| qcom,switch-freq = <2>; |
| qcom,ovp-val = <1>; |
| qcom,num-strings = <1>; |
| qcom,id = <0>; |
| }; |
| }; |
| }; |
| |
| &pm8941_chg { |
| status = "ok"; |
| |
| qcom,charging-disabled; |
| |
| qcom,chgr@1000 { |
| status = "ok"; |
| }; |
| |
| qcom,buck@1100 { |
| status = "ok"; |
| }; |
| |
| qcom,usb-chgpth@1300 { |
| status = "ok"; |
| }; |
| |
| qcom,dc-chgpth@1400 { |
| status = "disabled"; |
| }; |
| |
| qcom,boost@1500 { |
| status = "ok"; |
| }; |
| |
| qcom,chg-misc@1600 { |
| status = "ok"; |
| }; |
| }; |
| |
| &sdhc_1 { |
| vdd-supply = <&pm8941_l20>; |
| vdd-io-supply = <&pm8941_s3>; |
| |
| qcom,vdd-always-on; |
| qcom,vdd-lpm-sup; |
| qcom,vdd-voltage-level = <2950000 2950000>; |
| qcom,vdd-current-level = <800 500000>; |
| |
| qcom,vdd-io-always-on; |
| qcom,vdd-io-voltage-level = <1800000 1800000>; |
| qcom,vdd-io-current-level = <250 154000>; |
| |
| qcom,pad-pull-on = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */ |
| qcom,pad-pull-off = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */ |
| qcom,pad-drv-on = <0x4 0x4 0x4>; /* 10mA, 10mA, 10mA */ |
| qcom,pad-drv-off = <0x0 0x0 0x0>; /* 2mA, 2mA, 2mA */ |
| |
| qcom,nonremovable; |
| status = "ok"; |
| }; |
| |
| &sdhc_2 { |
| #address-cells = <0>; |
| interrupt-parent = <&sdhc_2>; |
| interrupts = <0 1 2>; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0xffffffff>; |
| interrupt-map = <0 &intc 0 125 0 |
| 1 &intc 0 221 0 |
| 2 &msmgpio 62 0x3>; |
| interrupt-names = "hc_irq", "pwr_irq", "status_irq"; |
| cd-gpios = <&msmgpio 62 0x1>; |
| |
| qcom,vdd-always-on; |
| qcom,vdd-lpm-sup; |
| |
| vdd-supply = <&pm8941_l21>; |
| vdd-io-supply = <&pm8941_l13>; |
| |
| qcom,vdd-voltage-level = <2950000 2950000>; |
| qcom,vdd-current-level = <9000 800000>; |
| |
| qcom,vdd-io-voltage-level = <1800000 2950000>; |
| qcom,vdd-io-current-level = <6 22000>; |
| |
| qcom,pad-pull-on = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */ |
| qcom,pad-pull-off = <0x0 0x3 0x3>; /* no-pull, pull-up, pull-up */ |
| qcom,pad-drv-on = <0x4 0x4 0x4>; /* 10mA, 10mA, 10mA */ |
| qcom,pad-drv-off = <0x0 0x0 0x0>; /* 2mA, 2mA, 2mA */ |
| status = "ok"; |
| }; |