Merge "arm/dt: msm8974: Add support for QHD sharp DSI panel"
diff --git a/arch/arm/boot/dts/dsi-panel-sharp-qhd-video.dtsi b/arch/arm/boot/dts/dsi-panel-sharp-qhd-video.dtsi
new file mode 100644
index 0000000..f853285
--- /dev/null
+++ b/arch/arm/boot/dts/dsi-panel-sharp-qhd-video.dtsi
@@ -0,0 +1,67 @@
+/* Copyright (c) 2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/ {
+ qcom,mdss_dsi_sharp_qhd_video {
+ compatible = "qcom,mdss-dsi-panel";
+ label = "sharp QHD LS043T1LE01 video mode dsi panel";
+ status = "disable";
+ qcom,dsi-ctrl-phandle = <&mdss_dsi0>;
+ qcom,enable-gpio = <&msmgpio 58 0>;
+ qcom,rst-gpio = <&pm8941_gpios 19 0>;
+ qcom,mdss-pan-res = <540 960>;
+ qcom,mdss-pan-bpp = <24>;
+ qcom,mdss-pan-dest = "display_1";
+ qcom,mdss-pan-porch-values = <80 32 48 15 10 3>; /* HBP, HPW, HFP, VBP, VPW, VFP */
+ qcom,mdss-pan-underflow-clr = <0xff>;
+ qcom,mdss-pan-bl-ctrl = "bl_ctrl_wled";
+ qcom,mdss-pan-bl-levels = <1 4095>;
+ qcom,mdss-pan-dsi-mode = <0>;
+ qcom,mdss-pan-dsi-h-pulse-mode = <1>;
+ qcom,mdss-pan-dsi-h-power-stop = <0 0 0>;
+ qcom,mdss-pan-dsi-bllp-power-stop = <1 1>;
+ qcom,mdss-pan-dsi-traffic-mode = <0>;
+ qcom,mdss-pan-dsi-dst-format = <3>;
+ qcom,mdss-pan-dsi-vc = <0>;
+ qcom,mdss-pan-dsi-rgb-swap = <2>;
+ qcom,mdss-pan-dsi-data-lanes = <1 1 0 0>;
+ qcom,mdss-pan-dsi-dlane-swap = <0>;
+ qcom,mdss-pan-dsi-t-clk = <0x1c 0x04>;
+ qcom,mdss-pan-dsi-stream = <0>;
+ qcom,mdss-pan-dsi-mdp-tr = <0x04>;
+ qcom,mdss-pan-dsi-dma-tr = <0x04>;
+ qcom,mdss-pan-frame-rate = <60>;
+ qcom,panel-phy-regulatorSettings = [07 09 03 00 /* Regulator settings */
+ 20 00 01];
+ qcom,panel-phy-timingSettings = [46 1d 20 00 39 3a
+ 21 21 32 03 04 00];
+ qcom,panel-phy-strengthCtrl = [ff 06];
+ qcom,panel-phy-bistCtrl = [00 00 b1 ff /* BIST Ctrl settings */
+ 00 00];
+ qcom,panel-phy-laneConfig = [00 00 00 00 00 00 00 01 97 /* lane0 config */
+ 00 00 00 00 05 00 00 01 97 /* lane1 config */
+ 00 00 00 00 0a 00 00 01 97 /* lane2 config */
+ 00 00 00 00 0f 00 00 01 97 /* lane3 config */
+ 00 c0 00 00 00 00 00 01 bb]; /* Clk ln config */
+ qcom,panel-on-cmds = [05 01 00 00 32 02 01 00 /* sw reset */
+ 05 01 00 00 0a 02 11 00 /* exit sleep */
+ 15 01 00 00 0a 02 53 2c /* backlight on */
+ 15 01 00 00 0a 02 51 ff /* brightness max */
+ 05 01 00 00 0a 02 29 00 /* display on */
+ 15 01 00 00 0a 02 ae 03 /* set num of lanes */
+ 15 01 00 00 0a 02 3a 77 /* rgb_888 */];
+ qcom,on-cmds-dsi-state = "DSI_LP_MODE";
+ qcom,panel-off-cmds = [05 01 00 00 0a 02 28 00 /* display off */
+ 05 01 00 00 78 02 10 00 /* enter sleep */];
+ qcom,off-cmds-dsi-state = "DSI_HS_MODE";
+ };
+};