ARM: dts: msm: Use phandles for PM8941 local slave IDs
Add a pair of phandles to represent PM8941 local slave IDs 0 and
1. The global slave ID used in SPMI transactions corresponding
to these local slave IDs changes depending upon whether or not
PM8941 is the primary PMIC in the system.
Using phandles for the local slave IDs allows the global slave
IDs for the local slave IDs to be specified on a per board basis.
This is required for MSM8974Pro-AC where the global slave IDs for
PM8941 change.
Change-Id: Idfe8a73467d5cfab2b206706df969f12b277b4ce
Signed-off-by: David Collins <collinsd@codeaurora.org>
diff --git a/arch/arm/boot/dts/apq8074-dragonboard.dtsi b/arch/arm/boot/dts/apq8074-dragonboard.dtsi
index 21e92ab..908978d 100644
--- a/arch/arm/boot/dts/apq8074-dragonboard.dtsi
+++ b/arch/arm/boot/dts/apq8074-dragonboard.dtsi
@@ -542,34 +542,32 @@
status = "disabled";
};
-&spmi_bus {
- qcom,pm8941@1 {
- qcom,leds@d000 {
- qcom,rgb_2 {
- status = "ok";
- qcom,default-state = "on";
- qcom,turn-off-delay-ms = <1000>;
- };
+&pm8941_lsid1 {
+ qcom,leds@d000 {
+ qcom,rgb_2 {
+ status = "ok";
+ qcom,default-state = "on";
+ qcom,turn-off-delay-ms = <1000>;
};
+ };
- qcom,leds@d800 {
- status = "okay";
- qcom,wled_0 {
- label = "wled";
- linux,name = "wled:backlight";
- linux,default-trigger = "bkl-trigger";
- qcom,cs-out-en;
- qcom,op-fdbck = <1>;
- qcom,default-state = "on";
- qcom,max-current = <20>;
- qcom,ctrl-delay-us = <0>;
- qcom,boost-curr-lim = <3>;
- qcom,cp-sel = <0>;
- qcom,switch-freq = <2>;
- qcom,ovp-val = <1>;
- qcom,num-strings = <1>;
- qcom,id = <0>;
- };
+ qcom,leds@d800 {
+ status = "okay";
+ qcom,wled_0 {
+ label = "wled";
+ linux,name = "wled:backlight";
+ linux,default-trigger = "bkl-trigger";
+ qcom,cs-out-en;
+ qcom,op-fdbck = <1>;
+ qcom,default-state = "on";
+ qcom,max-current = <20>;
+ qcom,ctrl-delay-us = <0>;
+ qcom,boost-curr-lim = <3>;
+ qcom,cp-sel = <0>;
+ qcom,switch-freq = <2>;
+ qcom,ovp-val = <1>;
+ qcom,num-strings = <1>;
+ qcom,id = <0>;
};
};
};
diff --git a/arch/arm/boot/dts/msm-pm8941.dtsi b/arch/arm/boot/dts/msm-pm8941.dtsi
index e72c8cd..fc828b7 100644
--- a/arch/arm/boot/dts/msm-pm8941.dtsi
+++ b/arch/arm/boot/dts/msm-pm8941.dtsi
@@ -15,1384 +15,1381 @@
#size-cells = <0>;
interrupt-controller;
#interrupt-cells = <3>;
+};
- qcom,pm8941@0 {
- spmi-slave-container;
- reg = <0x0>;
- #address-cells = <1>;
- #size-cells = <1>;
+&pm8941_lsid0 {
+ spmi-slave-container;
+ #address-cells = <1>;
+ #size-cells = <1>;
- pm8941_misc: qcom,misc@900 {
- compatible = "qcom,qpnp-misc";
- reg = <0x900 0x100>;
+ pm8941_misc: qcom,misc@900 {
+ compatible = "qcom,qpnp-misc";
+ reg = <0x900 0x100>;
+ };
+
+ qcom,revid@100 {
+ compatible = "qcom,qpnp-revid";
+ reg = <0x100 0x100>;
+ };
+
+ qcom,temp-alarm@2400 {
+ compatible = "qcom,qpnp-temp-alarm";
+ reg = <0x2400 0x100>;
+ interrupts = <0x0 0x24 0x0>;
+ label = "pm8941_tz";
+ qcom,channel-num = <8>;
+ qcom,threshold-set = <0>;
+ };
+
+ qcom,power-on@800 {
+ compatible = "qcom,qpnp-power-on";
+ reg = <0x800 0x100>;
+ interrupts = <0x0 0x8 0x0>,
+ <0x0 0x8 0x1>,
+ <0x0 0x8 0x4>,
+ <0x0 0x8 0x5>;
+ interrupt-names = "kpdpwr", "resin",
+ "resin-bark", "kpdpwr-resin-bark";
+ qcom,pon-dbc-delay = <15625>;
+ qcom,system-reset;
+ qcom,s3-debounce = <32>;
+
+ qcom,pon_1 {
+ qcom,pon-type = <0>;
+ qcom,pull-up = <1>;
+ linux,code = <116>;
};
- qcom,revid@100 {
- compatible = "qcom,qpnp-revid";
- reg = <0x100 0x100>;
+ qcom,pon_2 {
+ qcom,pon-type = <1>;
+ qcom,support-reset = <1>;
+ qcom,pull-up = <1>;
+ qcom,s1-timer = <0>;
+ qcom,s2-timer = <2000>;
+ qcom,s2-type = <1>;
+ linux,code = <114>;
};
- qcom,temp-alarm@2400 {
- compatible = "qcom,qpnp-temp-alarm";
- reg = <0x2400 0x100>;
- interrupts = <0x0 0x24 0x0>;
- label = "pm8941_tz";
- qcom,channel-num = <8>;
- qcom,threshold-set = <0>;
- };
-
- qcom,power-on@800 {
- compatible = "qcom,qpnp-power-on";
- reg = <0x800 0x100>;
- interrupts = <0x0 0x8 0x0>,
- <0x0 0x8 0x1>,
- <0x0 0x8 0x4>,
- <0x0 0x8 0x5>;
- interrupt-names = "kpdpwr", "resin",
- "resin-bark", "kpdpwr-resin-bark";
- qcom,pon-dbc-delay = <15625>;
- qcom,system-reset;
- qcom,s3-debounce = <32>;
-
- qcom,pon_1 {
- qcom,pon-type = <0>;
- qcom,pull-up = <1>;
- linux,code = <116>;
- };
-
- qcom,pon_2 {
- qcom,pon-type = <1>;
- qcom,support-reset = <1>;
- qcom,pull-up = <1>;
- qcom,s1-timer = <0>;
- qcom,s2-timer = <2000>;
- qcom,s2-type = <1>;
- linux,code = <114>;
- };
-
- qcom,pon_3 {
- qcom,pon-type = <3>;
- qcom,support-reset = <1>;
- qcom,s1-timer = <6720>;
- qcom,s2-timer = <2000>;
- qcom,s2-type = <7>;
- qcom,pull-up = <1>;
- };
- };
-
- bif_ctrl: qcom,bsi@1b00 {
- compatible = "qcom,qpnp-bsi";
- reg = <0x1b00 0x100>,
- <0x1208 0x1>;
- reg-names = "bsi-base", "batt-id-status";
- label = "pm8941-bsi";
- interrupts = <0x0 0x1b 0x0>,
- <0x0 0x1b 0x1>,
- <0x0 0x1b 0x2>,
- <0x0 0x12 0x0>;
- interrupt-names = "err",
- "rx",
- "tx",
- "batt-present";
- qcom,channel-num = <0x31>;
- qcom,pullup-ohms = <100000>;
- qcom,vref-microvolts = <1800000>;
- qcom,min-clock-period = <1000>;
- qcom,max-clock-period = <160000>;
- qcom,sample-rate = <4>;
- };
-
- pm8941_coincell: qcom,coincell@2800 {
- compatible = "qcom,qpnp-coincell";
- reg = <0x2800 0x100>;
- };
-
- pm8941_bms: qcom,bms {
- spmi-dev-container;
- compatible = "qcom,qpnp-bms";
- #address-cells = <1>;
- #size-cells = <1>;
- status = "disabled";
-
- qcom,r-sense-uohm = <10000>;
- qcom,v-cutoff-uv = <3400000>;
- qcom,max-voltage-uv = <4200000>;
- qcom,r-conn-mohm = <0>;
- qcom,shutdown-soc-valid-limit = <20>;
- qcom,adjust-soc-low-threshold = <15>;
- qcom,ocv-voltage-high-threshold-uv = <3750000>;
- qcom,ocv-voltage-low-threshold-uv = <3650000>;
- qcom,low-soc-calculate-soc-threshold = <15>;
- qcom,low-soc-calculate-soc-ms = <5000>;
- qcom,calculate-soc-ms = <20000>;
- qcom,chg-term-ua = <100000>;
- qcom,batt-type = <0>;
- qcom,low-voltage-threshold = <3420000>;
- qcom,tm-temp-margin = <5000>;
- qcom,low-ocv-correction-limit-uv = <100>;
- qcom,high-ocv-correction-limit-uv = <50>;
- qcom,hold-soc-est = <3>;
-
- qcom,bms-iadc@3800 {
- reg = <0x3800 0x100>;
- };
-
- qcom,bms-bms@4000 {
- reg = <0x4000 0x100>;
- interrupts = <0x0 0x40 0x0>,
- <0x0 0x40 0x1>,
- <0x0 0x40 0x2>,
- <0x0 0x40 0x3>,
- <0x0 0x40 0x4>,
- <0x0 0x40 0x5>,
- <0x0 0x40 0x6>,
- <0x0 0x40 0x7>;
-
- interrupt-names = "cc_thr",
- "ocv_for_r",
- "good_ocv",
- "charge_begin",
- "ocv_thr",
- "sw_cc_thr",
- "vsense_avg",
- "vsense_for_r";
-
- };
- };
-
- clkdiv@5b00 {
- reg = <0x5b00 0x100>;
- compatible = "qcom,qpnp-clkdiv";
- qcom,cxo-freq = <19200000>;
- };
-
- clkdiv@5c00 {
- reg = <0x5c00 0x100>;
- compatible = "qcom,qpnp-clkdiv";
- qcom,cxo-freq = <19200000>;
- };
-
- clkdiv@5d00 {
- reg = <0x5d00 0x1000>;
- compatible = "qcom,qpnp-clkdiv";
- qcom,cxo-freq = <19200000>;
- };
-
- pm8941_chg: qcom,charger {
- spmi-dev-container;
- compatible = "qcom,qpnp-charger";
- #address-cells = <1>;
- #size-cells = <1>;
- status = "disabled";
-
- qcom,vddmax-mv = <4200>;
- qcom,vddsafe-mv = <4230>;
- qcom,vinmin-mv = <4300>;
- qcom,ibatmax-ma = <1500>;
- qcom,ibatterm-ma = <100>;
- qcom,ibatsafe-ma = <1500>;
- qcom,thermal-mitigation = <1500 700 600 325>;
- qcom,cool-bat-decidegc = <100>;
- qcom,cool-bat-mv = <4100>;
- qcom,ibatmax-warm-ma = <350>;
- qcom,warm-bat-decidegc = <450>;
- qcom,warm-bat-mv = <4100>;
- qcom,ibatmax-cool-ma = <350>;
- qcom,vbatdet-delta-mv = <100>;
- qcom,resume-soc = <99>;
- qcom,tchg-mins = <150>;
-
- qcom,chgr@1000 {
- status = "disabled";
- reg = <0x1000 0x100>;
- interrupts = <0x0 0x10 0x0>,
- <0x0 0x10 0x1>,
- <0x0 0x10 0x2>,
- <0x0 0x10 0x3>,
- <0x0 0x10 0x4>,
- <0x0 0x10 0x5>,
- <0x0 0x10 0x6>,
- <0x0 0x10 0x7>;
-
- interrupt-names = "vbat-det-lo",
- "vbat-det-hi",
- "chgwdog",
- "state-change",
- "trkl-chg-on",
- "fast-chg-on",
- "chg-failed",
- "chg-done";
- };
-
- qcom,buck@1100 {
- status = "disabled";
- reg = <0x1100 0x100>;
- interrupts = <0x0 0x11 0x0>,
- <0x0 0x11 0x1>,
- <0x0 0x11 0x2>,
- <0x0 0x11 0x3>,
- <0x0 0x11 0x4>,
- <0x0 0x11 0x5>,
- <0x0 0x11 0x6>;
-
- interrupt-names = "vbat-ov",
- "vreg-ov",
- "overtemp",
- "vchg-loop",
- "ichg-loop",
- "ibat-loop",
- "vdd-loop";
- };
-
- qcom,bat-if@1200 {
- status = "disabled";
- reg = <0x1200 0x100>;
- interrupts = <0x0 0x12 0x0>,
- <0x0 0x12 0x1>,
- <0x0 0x12 0x2>,
- <0x0 0x12 0x3>,
- <0x0 0x12 0x4>;
-
- interrupt-names = "batt-pres",
- "bat-temp-ok",
- "bat-fet-on",
- "vcp-on",
- "psi";
-
- };
-
- pm8941_chg_otg: qcom,usb-chgpth@1300 {
- status = "disabled";
- reg = <0x1300 0x100>;
- interrupts = <0 0x13 0x0>,
- <0 0x13 0x1>,
- <0x0 0x13 0x2>;
-
- interrupt-names = "coarse-det-usb",
- "usbin-valid",
- "chg-gone";
- };
-
- qcom,dc-chgpth@1400 {
- status = "disabled";
- reg = <0x1400 0x100>;
- interrupts = <0x0 0x14 0x0>,
- <0x0 0x14 0x1>;
-
- interrupt-names = "coarse-det-dc",
- "dcin-valid";
- };
-
- pm8941_chg_boost: qcom,boost@1500 {
- status = "disabled";
- reg = <0x1500 0x100>;
- interrupts = <0x0 0x15 0x0>,
- <0x0 0x15 0x1>;
-
- interrupt-names = "boost-pwr-ok",
- "limit-error";
- };
-
- qcom,chg-misc@1600 {
- status = "disabled";
- reg = <0x1600 0x100>;
- };
- };
-
- pm8941_gpios: gpios {
- spmi-dev-container;
- compatible = "qcom,qpnp-pin";
- gpio-controller;
- #gpio-cells = <2>;
- #address-cells = <1>;
- #size-cells = <1>;
- label = "pm8941-gpio";
-
- gpio@c000 {
- reg = <0xc000 0x100>;
- qcom,pin-num = <1>;
- };
-
- gpio@c100 {
- reg = <0xc100 0x100>;
- qcom,pin-num = <2>;
- };
-
- gpio@c200 {
- reg = <0xc200 0x100>;
- qcom,pin-num = <3>;
- };
-
- gpio@c300 {
- reg = <0xc300 0x100>;
- qcom,pin-num = <4>;
- };
-
- gpio@c400 {
- reg = <0xc400 0x100>;
- qcom,pin-num = <5>;
- };
-
- gpio@c500 {
- reg = <0xc500 0x100>;
- qcom,pin-num = <6>;
- };
-
- gpio@c600 {
- reg = <0xc600 0x100>;
- qcom,pin-num = <7>;
- };
-
- gpio@c700 {
- reg = <0xc700 0x100>;
- qcom,pin-num = <8>;
- };
-
- gpio@c800 {
- reg = <0xc800 0x100>;
- qcom,pin-num = <9>;
- };
-
- gpio@c900 {
- reg = <0xc900 0x100>;
- qcom,pin-num = <10>;
- };
-
- gpio@ca00 {
- reg = <0xca00 0x100>;
- qcom,pin-num = <11>;
- };
-
- gpio@cb00 {
- reg = <0xcb00 0x100>;
- qcom,pin-num = <12>;
- };
-
- gpio@cc00 {
- reg = <0xcc00 0x100>;
- qcom,pin-num = <13>;
- };
-
- gpio@cd00 {
- reg = <0xcd00 0x100>;
- qcom,pin-num = <14>;
- };
-
- gpio@ce00 {
- reg = <0xce00 0x100>;
- qcom,pin-num = <15>;
- };
-
- gpio@cf00 {
- reg = <0xcf00 0x100>;
- qcom,pin-num = <16>;
- };
-
- gpio@d000 {
- reg = <0xd000 0x100>;
- qcom,pin-num = <17>;
- };
-
- gpio@d100 {
- reg = <0xd100 0x100>;
- qcom,pin-num = <18>;
- };
-
- gpio@d200 {
- reg = <0xd200 0x100>;
- qcom,pin-num = <19>;
- };
-
- gpio@d300 {
- reg = <0xd300 0x100>;
- qcom,pin-num = <20>;
- };
-
- gpio@d400 {
- reg = <0xd400 0x100>;
- qcom,pin-num = <21>;
- };
-
- gpio@d500 {
- reg = <0xd500 0x100>;
- qcom,pin-num = <22>;
- };
-
- gpio@d600 {
- reg = <0xd600 0x100>;
- qcom,pin-num = <23>;
- };
-
- gpio@d700 {
- reg = <0xd700 0x100>;
- qcom,pin-num = <24>;
- };
-
- gpio@d800 {
- reg = <0xd800 0x100>;
- qcom,pin-num = <25>;
- };
-
- gpio@d900 {
- reg = <0xd900 0x100>;
- qcom,pin-num = <26>;
- };
-
- gpio@da00 {
- reg = <0xda00 0x100>;
- qcom,pin-num = <27>;
- };
-
- gpio@db00 {
- reg = <0xdb00 0x100>;
- qcom,pin-num = <28>;
- };
-
- gpio@dc00 {
- reg = <0xdc00 0x100>;
- qcom,pin-num = <29>;
- };
-
- gpio@dd00 {
- reg = <0xdd00 0x100>;
- qcom,pin-num = <30>;
- };
-
- gpio@de00 {
- reg = <0xde00 0x100>;
- qcom,pin-num = <31>;
- };
-
- gpio@df00 {
- reg = <0xdf00 0x100>;
- qcom,pin-num = <32>;
- };
-
- gpio@e000 {
- reg = <0xe000 0x100>;
- qcom,pin-num = <33>;
- };
-
- gpio@e100 {
- reg = <0xe100 0x100>;
- qcom,pin-num = <34>;
- };
-
- gpio@e200 {
- reg = <0xe200 0x100>;
- qcom,pin-num = <35>;
- };
-
- gpio@e300 {
- reg = <0xe300 0x100>;
- qcom,pin-num = <36>;
- };
- };
-
- pm8941_mpps: mpps {
- spmi-dev-container;
- compatible = "qcom,qpnp-pin";
- gpio-controller;
- #gpio-cells = <2>;
- #address-cells = <1>;
- #size-cells = <1>;
- label = "pm8941-mpp";
-
- mpp@a000 {
- reg = <0xa000 0x100>;
- qcom,pin-num = <1>;
- };
-
- mpp@a100 {
- reg = <0xa100 0x100>;
- qcom,pin-num = <2>;
- };
-
- mpp@a200 {
- reg = <0xa200 0x100>;
- qcom,pin-num = <3>;
- };
-
- mpp@a300 {
- reg = <0xa300 0x100>;
- qcom,pin-num = <4>;
- };
-
- mpp@a400 {
- reg = <0xa400 0x100>;
- qcom,pin-num = <5>;
- };
-
- mpp@a500 {
- reg = <0xa500 0x100>;
- qcom,pin-num = <6>;
- };
-
- mpp@a600 {
- reg = <0xa600 0x100>;
- qcom,pin-num = <7>;
- };
-
- mpp@a700 {
- reg = <0xa700 0x100>;
- qcom,pin-num = <8>;
- };
- };
-
- qcom,pm8941_rtc {
- spmi-dev-container;
- compatible = "qcom,qpnp-rtc";
- #address-cells = <1>;
- #size-cells = <1>;
- qcom,qpnp-rtc-write = <0>;
- qcom,qpnp-rtc-alarm-pwrup = <0>;
-
- qcom,pm8941_rtc_rw@6000 {
- reg = <0x6000 0x100>;
- };
- qcom,pm8941_rtc_alarm@6100 {
- reg = <0x6100 0x100>;
- interrupts = <0x0 0x61 0x1>;
- };
- };
-
- pm8941_vadc: vadc@3100 {
- compatible = "qcom,qpnp-vadc";
- reg = <0x3100 0x100>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <0x0 0x31 0x0>;
- interrupt-names = "eoc-int-en-set";
- qcom,adc-bit-resolution = <15>;
- qcom,adc-vdd-reference = <1800>;
-
- chan@0 {
- label = "usb_in";
- reg = <0>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <4>;
- qcom,calibration-type = "absolute";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <0>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@1 {
- label = "dc_in";
- reg = <1>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <4>;
- qcom,calibration-type = "absolute";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <0>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@2 {
- label = "vchg_sns";
- reg = <2>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <3>;
- qcom,calibration-type = "absolute";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <0>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@3 {
- label = "spare1_div3";
- reg = <3>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <1>;
- qcom,calibration-type = "absolute";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <0>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@4 {
- label = "usb_id_mv";
- reg = <4>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <1>;
- qcom,calibration-type = "absolute";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <0>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@5 {
- label = "vcoin";
- reg = <5>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <1>;
- qcom,calibration-type = "absolute";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <0>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@6 {
- label = "vbat_sns";
- reg = <6>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <1>;
- qcom,calibration-type = "absolute";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <0>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@7 {
- label = "vph_pwr";
- reg = <7>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <1>;
- qcom,calibration-type = "absolute";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <0>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@8 {
- label = "die_temp";
- reg = <8>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "absolute";
- qcom,scale-function = <3>;
- qcom,hw-settle-time = <0>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@9 {
- label = "ref_625mv";
- reg = <9>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "absolute";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <0>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@a {
- label = "ref_1250v";
- reg = <0xa>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "absolute";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <0>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@30 {
- label = "batt_therm";
- reg = <0x30>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <1>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@31 {
- label = "batt_id";
- reg = <0x31>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@b2 {
- label = "xo_therm_pu2";
- reg = <0xb2>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <4>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@b3 {
- label = "msm_therm";
- reg = <0xb3>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <2>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@b4 {
- label = "emmc_therm";
- reg = <0xb4>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <2>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@b5 {
- label = "pa_therm0";
- reg = <0xb5>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <2>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@b7 {
- label = "pa_therm1";
- reg = <0xb7>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <2>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@b8 {
- label = "quiet_therm";
- reg = <0xb8>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <2>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@b9 {
- label = "usb_id";
- reg = <0xb9>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <0>;
- };
-
- chan@39 {
- label = "usb_id_nopull";
- reg = <0x39>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <0>;
- };
- };
-
- pm8941_iadc: iadc@3600 {
- compatible = "qcom,qpnp-iadc";
- reg = <0x3600 0x100>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <0x0 0x36 0x0>;
- interrupt-names = "eoc-int-en-set";
- qcom,adc-bit-resolution = <16>;
- qcom,adc-vdd-reference = <1800>;
-
- chan@0 {
- label = "internal_rsense";
- reg = <0>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <1>;
- qcom,calibration-type = "absolute";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <0>;
- qcom,fast-avg-setup = <0>;
- };
- };
-
- pm8941_adc_tm: qcom,vadc@3400 {
- compatible = "qcom,qpnp-adc-tm";
- reg = <0x3400 0x100>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <0x0 0x34 0x0>,
- <0x0 0x34 0x3>,
- <0x0 0x34 0x4>;
- interrupt-names = "eoc-int-en-set",
- "high-thr-en-set",
- "low-thr-en-set";
- qcom,adc-bit-resolution = <15>;
- qcom,adc-vdd-reference = <1800>;
-
- /* Channel Node */
- chan@b9 {
- label = "usb_id";
- reg = <0xb9>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <2>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <3>;
- qcom,btm-channel-number = <0x48>;
- };
-
- chan@30 {
- label = "batt_therm";
- reg = <0x30>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <1>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <3>;
- qcom,btm-channel-number = <0x68>;
- };
-
- chan@8 {
- label = "die_temp";
- reg = <8>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "absolute";
- qcom,scale-function = <3>;
- qcom,hw-settle-time = <0>;
- qcom,fast-avg-setup = <3>;
- qcom,btm-channel-number = <0x70>;
- };
-
- chan@6 {
- label = "vbat_sns";
- reg = <6>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <1>;
- qcom,calibration-type = "absolute";
- qcom,scale-function = <0>;
- qcom,hw-settle-time = <0>;
- qcom,fast-avg-setup = <3>;
- qcom,btm-channel-number = <0x78>;
- };
-
- chan@b5 {
- label = "pa_therm0";
- reg = <0xb5>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <2>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <3>;
- qcom,btm-channel-number = <0x80>;
- qcom,thermal-node;
- };
-
- chan@b7 {
- label = "pa_therm1";
- reg = <0xb7>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <2>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <3>;
- qcom,btm-channel-number = <0x88>;
- qcom,thermal-node;
- };
-
- chan@b4 {
- label = "emmc_therm";
- reg = <0xb4>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <2>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <3>;
- qcom,btm-channel-number = <0x90>;
- qcom,thermal-node;
- };
-
- chan@b3 {
- label = "msm_therm";
- reg = <0xb3>;
- qcom,decimation = <0>;
- qcom,pre-div-channel-scaling = <0>;
- qcom,calibration-type = "ratiometric";
- qcom,scale-function = <2>;
- qcom,hw-settle-time = <2>;
- qcom,fast-avg-setup = <3>;
- qcom,btm-channel-number = <0x98>;
- qcom,thermal-node;
- };
+ qcom,pon_3 {
+ qcom,pon-type = <3>;
+ qcom,support-reset = <1>;
+ qcom,s1-timer = <6720>;
+ qcom,s2-timer = <2000>;
+ qcom,s2-type = <7>;
+ qcom,pull-up = <1>;
};
};
- qcom,pm8941@1 {
- spmi-slave-container;
- reg = <0x1>;
+ bif_ctrl: qcom,bsi@1b00 {
+ compatible = "qcom,qpnp-bsi";
+ reg = <0x1b00 0x100>,
+ <0x1208 0x1>;
+ reg-names = "bsi-base", "batt-id-status";
+ label = "pm8941-bsi";
+ interrupts = <0x0 0x1b 0x0>,
+ <0x0 0x1b 0x1>,
+ <0x0 0x1b 0x2>,
+ <0x0 0x12 0x0>;
+ interrupt-names = "err",
+ "rx",
+ "tx",
+ "batt-present";
+ qcom,channel-num = <0x31>;
+ qcom,pullup-ohms = <100000>;
+ qcom,vref-microvolts = <1800000>;
+ qcom,min-clock-period = <1000>;
+ qcom,max-clock-period = <160000>;
+ qcom,sample-rate = <4>;
+ };
+
+ pm8941_coincell: qcom,coincell@2800 {
+ compatible = "qcom,qpnp-coincell";
+ reg = <0x2800 0x100>;
+ };
+
+ pm8941_bms: qcom,bms {
+ spmi-dev-container;
+ compatible = "qcom,qpnp-bms";
#address-cells = <1>;
#size-cells = <1>;
+ status = "disabled";
- regulator@1400 {
- regulator-name = "8941_s1";
- spmi-dev-container;
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "qcom,qpnp-regulator";
- reg = <0x1400 0x300>;
- status = "disabled";
+ qcom,r-sense-uohm = <10000>;
+ qcom,v-cutoff-uv = <3400000>;
+ qcom,max-voltage-uv = <4200000>;
+ qcom,r-conn-mohm = <0>;
+ qcom,shutdown-soc-valid-limit = <20>;
+ qcom,adjust-soc-low-threshold = <15>;
+ qcom,ocv-voltage-high-threshold-uv = <3750000>;
+ qcom,ocv-voltage-low-threshold-uv = <3650000>;
+ qcom,low-soc-calculate-soc-threshold = <15>;
+ qcom,low-soc-calculate-soc-ms = <5000>;
+ qcom,calculate-soc-ms = <20000>;
+ qcom,chg-term-ua = <100000>;
+ qcom,batt-type = <0>;
+ qcom,low-voltage-threshold = <3420000>;
+ qcom,tm-temp-margin = <5000>;
+ qcom,low-ocv-correction-limit-uv = <100>;
+ qcom,high-ocv-correction-limit-uv = <50>;
+ qcom,hold-soc-est = <3>;
- qcom,ctl@1400 {
- reg = <0x1400 0x100>;
- };
- qcom,ps@1500 {
- reg = <0x1500 0x100>;
- };
- qcom,freq@1600 {
- reg = <0x1600 0x100>;
- };
+ qcom,bms-iadc@3800 {
+ reg = <0x3800 0x100>;
};
- regulator@1700 {
- regulator-name = "8941_s2";
- spmi-dev-container;
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "qcom,qpnp-regulator";
- reg = <0x1700 0x300>;
- status = "disabled";
-
- qcom,ctl@1700 {
- reg = <0x1700 0x100>;
- };
- qcom,ps@1800 {
- reg = <0x1800 0x100>;
- };
- qcom,freq@1900 {
- reg = <0x1900 0x100>;
- };
- };
-
- regulator@1a00 {
- regulator-name = "8941_s3";
- spmi-dev-container;
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "qcom,qpnp-regulator";
- reg = <0x1a00 0x300>;
- status = "disabled";
-
- qcom,ctl@1a00 {
- reg = <0x1a00 0x100>;
- };
- qcom,ps@1b00 {
- reg = <0x1b00 0x100>;
- };
- qcom,freq@1c00 {
- reg = <0x1c00 0x100>;
- };
- };
-
- regulator@a000 {
- regulator-name = "8941_boost";
- reg = <0xa000 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@4000 {
- regulator-name = "8941_l1";
+ qcom,bms-bms@4000 {
reg = <0x4000 0x100>;
- compatible = "qcom,qpnp-regulator";
+ interrupts = <0x0 0x40 0x0>,
+ <0x0 0x40 0x1>,
+ <0x0 0x40 0x2>,
+ <0x0 0x40 0x3>,
+ <0x0 0x40 0x4>,
+ <0x0 0x40 0x5>,
+ <0x0 0x40 0x6>,
+ <0x0 0x40 0x7>;
+
+ interrupt-names = "cc_thr",
+ "ocv_for_r",
+ "good_ocv",
+ "charge_begin",
+ "ocv_thr",
+ "sw_cc_thr",
+ "vsense_avg",
+ "vsense_for_r";
+ };
+ };
+
+ clkdiv@5b00 {
+ reg = <0x5b00 0x100>;
+ compatible = "qcom,qpnp-clkdiv";
+ qcom,cxo-freq = <19200000>;
+ };
+
+ clkdiv@5c00 {
+ reg = <0x5c00 0x100>;
+ compatible = "qcom,qpnp-clkdiv";
+ qcom,cxo-freq = <19200000>;
+ };
+
+ clkdiv@5d00 {
+ reg = <0x5d00 0x1000>;
+ compatible = "qcom,qpnp-clkdiv";
+ qcom,cxo-freq = <19200000>;
+ };
+
+ pm8941_chg: qcom,charger {
+ spmi-dev-container;
+ compatible = "qcom,qpnp-charger";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "disabled";
+
+ qcom,vddmax-mv = <4200>;
+ qcom,vddsafe-mv = <4230>;
+ qcom,vinmin-mv = <4300>;
+ qcom,ibatmax-ma = <1500>;
+ qcom,ibatterm-ma = <100>;
+ qcom,ibatsafe-ma = <1500>;
+ qcom,thermal-mitigation = <1500 700 600 325>;
+ qcom,cool-bat-decidegc = <100>;
+ qcom,cool-bat-mv = <4100>;
+ qcom,ibatmax-warm-ma = <350>;
+ qcom,warm-bat-decidegc = <450>;
+ qcom,warm-bat-mv = <4100>;
+ qcom,ibatmax-cool-ma = <350>;
+ qcom,vbatdet-delta-mv = <100>;
+ qcom,resume-soc = <99>;
+ qcom,tchg-mins = <150>;
+
+ qcom,chgr@1000 {
status = "disabled";
+ reg = <0x1000 0x100>;
+ interrupts = <0x0 0x10 0x0>,
+ <0x0 0x10 0x1>,
+ <0x0 0x10 0x2>,
+ <0x0 0x10 0x3>,
+ <0x0 0x10 0x4>,
+ <0x0 0x10 0x5>,
+ <0x0 0x10 0x6>,
+ <0x0 0x10 0x7>;
+
+ interrupt-names = "vbat-det-lo",
+ "vbat-det-hi",
+ "chgwdog",
+ "state-change",
+ "trkl-chg-on",
+ "fast-chg-on",
+ "chg-failed",
+ "chg-done";
};
- regulator@4100 {
- regulator-name = "8941_l2";
- reg = <0x4100 0x100>;
- compatible = "qcom,qpnp-regulator";
+ qcom,buck@1100 {
status = "disabled";
+ reg = <0x1100 0x100>;
+ interrupts = <0x0 0x11 0x0>,
+ <0x0 0x11 0x1>,
+ <0x0 0x11 0x2>,
+ <0x0 0x11 0x3>,
+ <0x0 0x11 0x4>,
+ <0x0 0x11 0x5>,
+ <0x0 0x11 0x6>;
+
+ interrupt-names = "vbat-ov",
+ "vreg-ov",
+ "overtemp",
+ "vchg-loop",
+ "ichg-loop",
+ "ibat-loop",
+ "vdd-loop";
};
- regulator@4200 {
- regulator-name = "8941_l3";
- reg = <0x4200 0x100>;
- compatible = "qcom,qpnp-regulator";
+ qcom,bat-if@1200 {
status = "disabled";
+ reg = <0x1200 0x100>;
+ interrupts = <0x0 0x12 0x0>,
+ <0x0 0x12 0x1>,
+ <0x0 0x12 0x2>,
+ <0x0 0x12 0x3>,
+ <0x0 0x12 0x4>;
+
+ interrupt-names = "batt-pres",
+ "bat-temp-ok",
+ "bat-fet-on",
+ "vcp-on",
+ "psi";
+
};
- regulator@4300 {
- regulator-name = "8941_l4";
- reg = <0x4300 0x100>;
- compatible = "qcom,qpnp-regulator";
+ pm8941_chg_otg: qcom,usb-chgpth@1300 {
status = "disabled";
+ reg = <0x1300 0x100>;
+ interrupts = <0 0x13 0x0>,
+ <0 0x13 0x1>,
+ <0x0 0x13 0x2>;
+
+ interrupt-names = "coarse-det-usb",
+ "usbin-valid",
+ "chg-gone";
};
- regulator@4400 {
- regulator-name = "8941_l5";
- reg = <0x4400 0x100>;
- compatible = "qcom,qpnp-regulator";
- qcom,force-type = <0x04 0x10>;
+ qcom,dc-chgpth@1400 {
status = "disabled";
+ reg = <0x1400 0x100>;
+ interrupts = <0x0 0x14 0x0>,
+ <0x0 0x14 0x1>;
+
+ interrupt-names = "coarse-det-dc",
+ "dcin-valid";
};
- regulator@4500 {
- regulator-name = "8941_l6";
- reg = <0x4500 0x100>;
- compatible = "qcom,qpnp-regulator";
+ pm8941_chg_boost: qcom,boost@1500 {
status = "disabled";
+ reg = <0x1500 0x100>;
+ interrupts = <0x0 0x15 0x0>,
+ <0x0 0x15 0x1>;
+
+ interrupt-names = "boost-pwr-ok",
+ "limit-error";
};
- regulator@4600 {
- regulator-name = "8941_l7";
- reg = <0x4600 0x100>;
- compatible = "qcom,qpnp-regulator";
- qcom,force-type = <0x04 0x10>;
+ qcom,chg-misc@1600 {
status = "disabled";
+ reg = <0x1600 0x100>;
};
+ };
- regulator@4700 {
- regulator-name = "8941_l8";
- reg = <0x4700 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
+ pm8941_gpios: gpios {
+ spmi-dev-container;
+ compatible = "qcom,qpnp-pin";
+ gpio-controller;
+ #gpio-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ label = "pm8941-gpio";
- regulator@4800 {
- regulator-name = "8941_l9";
- reg = <0x4800 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@4900 {
- regulator-name = "8941_l10";
- reg = <0x4900 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@4a00 {
- regulator-name = "8941_l11";
- reg = <0x4a00 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@4b00 {
- regulator-name = "8941_l12";
- reg = <0x4b00 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@4c00 {
- regulator-name = "8941_l13";
- reg = <0x4c00 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@4d00 {
- regulator-name = "8941_l14";
- reg = <0x4d00 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@4e00 {
- regulator-name = "8941_l15";
- reg = <0x4e00 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@4f00 {
- regulator-name = "8941_l16";
- reg = <0x4f00 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@5000 {
- regulator-name = "8941_l17";
- reg = <0x5000 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@5100 {
- regulator-name = "8941_l18";
- reg = <0x5100 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@5200 {
- regulator-name = "8941_l19";
- reg = <0x5200 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@5300 {
- regulator-name = "8941_l20";
- reg = <0x5300 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@5400 {
- regulator-name = "8941_l21";
- reg = <0x5400 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@5500 {
- regulator-name = "8941_l22";
- reg = <0x5500 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@5600 {
- regulator-name = "8941_l23";
- reg = <0x5600 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@5700 {
- regulator-name = "8941_l24";
- reg = <0x5700 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@8000 {
- regulator-name = "8941_lvs1";
- reg = <0x8000 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@8100 {
- regulator-name = "8941_lvs2";
- reg = <0x8100 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@8200 {
- regulator-name = "8941_lvs3";
- reg = <0x8200 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@8300 {
- regulator-name = "8941_mvs1";
- reg = <0x8300 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- regulator@8400 {
- regulator-name = "8941_mvs2";
- reg = <0x8400 0x100>;
- compatible = "qcom,qpnp-regulator";
- status = "disabled";
- };
-
- qcom,vibrator@c000 {
- compatible = "qcom,qpnp-vibrator";
+ gpio@c000 {
reg = <0xc000 0x100>;
- label = "vibrator";
- status = "disabled";
+ qcom,pin-num = <1>;
};
- qcom,leds@d000 {
- compatible = "qcom,leds-qpnp";
+ gpio@c100 {
+ reg = <0xc100 0x100>;
+ qcom,pin-num = <2>;
+ };
+
+ gpio@c200 {
+ reg = <0xc200 0x100>;
+ qcom,pin-num = <3>;
+ };
+
+ gpio@c300 {
+ reg = <0xc300 0x100>;
+ qcom,pin-num = <4>;
+ };
+
+ gpio@c400 {
+ reg = <0xc400 0x100>;
+ qcom,pin-num = <5>;
+ };
+
+ gpio@c500 {
+ reg = <0xc500 0x100>;
+ qcom,pin-num = <6>;
+ };
+
+ gpio@c600 {
+ reg = <0xc600 0x100>;
+ qcom,pin-num = <7>;
+ };
+
+ gpio@c700 {
+ reg = <0xc700 0x100>;
+ qcom,pin-num = <8>;
+ };
+
+ gpio@c800 {
+ reg = <0xc800 0x100>;
+ qcom,pin-num = <9>;
+ };
+
+ gpio@c900 {
+ reg = <0xc900 0x100>;
+ qcom,pin-num = <10>;
+ };
+
+ gpio@ca00 {
+ reg = <0xca00 0x100>;
+ qcom,pin-num = <11>;
+ };
+
+ gpio@cb00 {
+ reg = <0xcb00 0x100>;
+ qcom,pin-num = <12>;
+ };
+
+ gpio@cc00 {
+ reg = <0xcc00 0x100>;
+ qcom,pin-num = <13>;
+ };
+
+ gpio@cd00 {
+ reg = <0xcd00 0x100>;
+ qcom,pin-num = <14>;
+ };
+
+ gpio@ce00 {
+ reg = <0xce00 0x100>;
+ qcom,pin-num = <15>;
+ };
+
+ gpio@cf00 {
+ reg = <0xcf00 0x100>;
+ qcom,pin-num = <16>;
+ };
+
+ gpio@d000 {
reg = <0xd000 0x100>;
- label = "rgb";
+ qcom,pin-num = <17>;
};
- qcom,leds@d100 {
- compatible = "qcom,leds-qpnp";
+ gpio@d100 {
reg = <0xd100 0x100>;
- label = "rgb";
+ qcom,pin-num = <18>;
};
- qcom,leds@d200 {
- compatible = "qcom,leds-qpnp";
+ gpio@d200 {
reg = <0xd200 0x100>;
- label = "rgb";
+ qcom,pin-num = <19>;
};
- qcom,leds@d300 {
- compatible = "qcom,leds-qpnp";
+ gpio@d300 {
reg = <0xd300 0x100>;
- label = "flash";
- flash_boost-supply = <&pm8941_chg_boost>;
+ qcom,pin-num = <20>;
};
- qcom,leds@d400 {
- compatible = "qcom,leds-qpnp";
+ gpio@d400 {
reg = <0xd400 0x100>;
- label = "flash";
+ qcom,pin-num = <21>;
};
- qcom,leds@d500 {
- compatible = "qcom,leds-qpnp";
+ gpio@d500 {
reg = <0xd500 0x100>;
- label = "flash";
+ qcom,pin-num = <22>;
};
- qcom,leds@d600 {
- compatible = "qcom,leds-qpnp";
+ gpio@d600 {
reg = <0xd600 0x100>;
- label = "flash";
+ qcom,pin-num = <23>;
};
- qcom,leds@d700 {
- compatible = "qcom,leds-qpnp";
+ gpio@d700 {
reg = <0xd700 0x100>;
- label = "flash";
+ qcom,pin-num = <24>;
};
- qcom,leds@d800 {
- compatible = "qcom,leds-qpnp";
+ gpio@d800 {
reg = <0xd800 0x100>;
- label = "wled";
+ qcom,pin-num = <25>;
};
- qcom,leds@d900 {
- compatible = "qcom,leds-qpnp";
+ gpio@d900 {
reg = <0xd900 0x100>;
- label = "wled";
+ qcom,pin-num = <26>;
};
- qcom,leds@da00 {
- compatible = "qcom,leds-qpnp";
+ gpio@da00 {
reg = <0xda00 0x100>;
- label = "wled";
+ qcom,pin-num = <27>;
};
- qcom,leds@db00 {
- compatible = "qcom,leds-qpnp";
+ gpio@db00 {
reg = <0xdb00 0x100>;
- label = "wled";
+ qcom,pin-num = <28>;
};
- qcom,leds@dc00 {
- compatible = "qcom,leds-qpnp";
+ gpio@dc00 {
reg = <0xdc00 0x100>;
- label = "wled";
+ qcom,pin-num = <29>;
};
- qcom,leds@dd00 {
- compatible = "qcom,leds-qpnp";
+ gpio@dd00 {
reg = <0xdd00 0x100>;
- label = "wled";
+ qcom,pin-num = <30>;
};
- qcom,leds@de00 {
- compatible = "qcom,leds-qpnp";
+ gpio@de00 {
reg = <0xde00 0x100>;
- label = "wled";
+ qcom,pin-num = <31>;
};
- qcom,leds@df00 {
- compatible = "qcom,leds-qpnp";
+ gpio@df00 {
reg = <0xdf00 0x100>;
- label = "wled";
+ qcom,pin-num = <32>;
};
- qcom,leds@e000 {
- compatible = "qcom,leds-qpnp";
+ gpio@e000 {
reg = <0xe000 0x100>;
- label = "wled";
+ qcom,pin-num = <33>;
};
- qcom,leds@e100 {
- compatible = "qcom,leds-qpnp";
+ gpio@e100 {
reg = <0xe100 0x100>;
- label = "wled";
+ qcom,pin-num = <34>;
};
- pwm@b100 {
- compatible = "qcom,qpnp-pwm";
- reg = <0xb100 0x100>,
- <0xb042 0x7e>;
- reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
- qcom,channel-id = <0>;
+ gpio@e200 {
+ reg = <0xe200 0x100>;
+ qcom,pin-num = <35>;
};
- pwm@b200 {
- compatible = "qcom,qpnp-pwm";
- reg = <0xb200 0x100>,
- <0xb042 0x7e>;
- reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
- qcom,channel-id = <1>;
+ gpio@e300 {
+ reg = <0xe300 0x100>;
+ qcom,pin-num = <36>;
+ };
+ };
+
+ pm8941_mpps: mpps {
+ spmi-dev-container;
+ compatible = "qcom,qpnp-pin";
+ gpio-controller;
+ #gpio-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ label = "pm8941-mpp";
+
+ mpp@a000 {
+ reg = <0xa000 0x100>;
+ qcom,pin-num = <1>;
};
- pwm@b300 {
- compatible = "qcom,qpnp-pwm";
- reg = <0xb300 0x100>,
- <0xb042 0x7e>;
- reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
- qcom,channel-id = <2>;
+ mpp@a100 {
+ reg = <0xa100 0x100>;
+ qcom,pin-num = <2>;
};
- pwm@b400 {
- compatible = "qcom,qpnp-pwm";
- reg = <0xb400 0x100>,
- <0xb042 0x7e>;
- reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
- qcom,channel-id = <3>;
+ mpp@a200 {
+ reg = <0xa200 0x100>;
+ qcom,pin-num = <3>;
};
- pwm@b500 {
- compatible = "qcom,qpnp-pwm";
- reg = <0xb500 0x100>,
- <0xb042 0x7e>;
- reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
- qcom,channel-id = <4>;
+ mpp@a300 {
+ reg = <0xa300 0x100>;
+ qcom,pin-num = <4>;
};
- pwm@b600 {
- compatible = "qcom,qpnp-pwm";
- reg = <0xb600 0x100>,
- <0xb042 0x7e>;
- reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
- qcom,channel-id = <5>;
+ mpp@a400 {
+ reg = <0xa400 0x100>;
+ qcom,pin-num = <5>;
};
- pwm@b700 {
- compatible = "qcom,qpnp-pwm";
- reg = <0xb700 0x100>,
- <0xb042 0x7e>;
- reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
- qcom,channel-id = <6>;
+ mpp@a500 {
+ reg = <0xa500 0x100>;
+ qcom,pin-num = <6>;
};
- pwm@b800 {
- compatible = "qcom,qpnp-pwm";
- reg = <0xb800 0x100>,
- <0xb042 0x7e>;
- reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
- qcom,channel-id = <7>;
+ mpp@a600 {
+ reg = <0xa600 0x100>;
+ qcom,pin-num = <7>;
};
+
+ mpp@a700 {
+ reg = <0xa700 0x100>;
+ qcom,pin-num = <8>;
+ };
+ };
+
+ qcom,pm8941_rtc {
+ spmi-dev-container;
+ compatible = "qcom,qpnp-rtc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ qcom,qpnp-rtc-write = <0>;
+ qcom,qpnp-rtc-alarm-pwrup = <0>;
+
+ qcom,pm8941_rtc_rw@6000 {
+ reg = <0x6000 0x100>;
+ };
+ qcom,pm8941_rtc_alarm@6100 {
+ reg = <0x6100 0x100>;
+ interrupts = <0x0 0x61 0x1>;
+ };
+ };
+
+ pm8941_vadc: vadc@3100 {
+ compatible = "qcom,qpnp-vadc";
+ reg = <0x3100 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0x0 0x31 0x0>;
+ interrupt-names = "eoc-int-en-set";
+ qcom,adc-bit-resolution = <15>;
+ qcom,adc-vdd-reference = <1800>;
+
+ chan@0 {
+ label = "usb_in";
+ reg = <0>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <4>;
+ qcom,calibration-type = "absolute";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <0>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@1 {
+ label = "dc_in";
+ reg = <1>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <4>;
+ qcom,calibration-type = "absolute";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <0>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@2 {
+ label = "vchg_sns";
+ reg = <2>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <3>;
+ qcom,calibration-type = "absolute";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <0>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@3 {
+ label = "spare1_div3";
+ reg = <3>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <1>;
+ qcom,calibration-type = "absolute";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <0>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@4 {
+ label = "usb_id_mv";
+ reg = <4>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <1>;
+ qcom,calibration-type = "absolute";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <0>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@5 {
+ label = "vcoin";
+ reg = <5>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <1>;
+ qcom,calibration-type = "absolute";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <0>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@6 {
+ label = "vbat_sns";
+ reg = <6>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <1>;
+ qcom,calibration-type = "absolute";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <0>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@7 {
+ label = "vph_pwr";
+ reg = <7>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <1>;
+ qcom,calibration-type = "absolute";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <0>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@8 {
+ label = "die_temp";
+ reg = <8>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "absolute";
+ qcom,scale-function = <3>;
+ qcom,hw-settle-time = <0>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@9 {
+ label = "ref_625mv";
+ reg = <9>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "absolute";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <0>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@a {
+ label = "ref_1250v";
+ reg = <0xa>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "absolute";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <0>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@30 {
+ label = "batt_therm";
+ reg = <0x30>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <1>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@31 {
+ label = "batt_id";
+ reg = <0x31>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@b2 {
+ label = "xo_therm_pu2";
+ reg = <0xb2>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <4>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@b3 {
+ label = "msm_therm";
+ reg = <0xb3>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <2>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@b4 {
+ label = "emmc_therm";
+ reg = <0xb4>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <2>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@b5 {
+ label = "pa_therm0";
+ reg = <0xb5>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <2>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@b7 {
+ label = "pa_therm1";
+ reg = <0xb7>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <2>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@b8 {
+ label = "quiet_therm";
+ reg = <0xb8>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <2>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@b9 {
+ label = "usb_id";
+ reg = <0xb9>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <0>;
+ };
+
+ chan@39 {
+ label = "usb_id_nopull";
+ reg = <0x39>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <0>;
+ };
+ };
+
+ pm8941_iadc: iadc@3600 {
+ compatible = "qcom,qpnp-iadc";
+ reg = <0x3600 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0x0 0x36 0x0>;
+ interrupt-names = "eoc-int-en-set";
+ qcom,adc-bit-resolution = <16>;
+ qcom,adc-vdd-reference = <1800>;
+
+ chan@0 {
+ label = "internal_rsense";
+ reg = <0>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <1>;
+ qcom,calibration-type = "absolute";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <0>;
+ qcom,fast-avg-setup = <0>;
+ };
+ };
+
+ pm8941_adc_tm: qcom,vadc@3400 {
+ compatible = "qcom,qpnp-adc-tm";
+ reg = <0x3400 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0x0 0x34 0x0>,
+ <0x0 0x34 0x3>,
+ <0x0 0x34 0x4>;
+ interrupt-names = "eoc-int-en-set",
+ "high-thr-en-set",
+ "low-thr-en-set";
+ qcom,adc-bit-resolution = <15>;
+ qcom,adc-vdd-reference = <1800>;
+
+ /* Channel Node */
+ chan@b9 {
+ label = "usb_id";
+ reg = <0xb9>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <2>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <3>;
+ qcom,btm-channel-number = <0x48>;
+ };
+
+ chan@30 {
+ label = "batt_therm";
+ reg = <0x30>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <1>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <3>;
+ qcom,btm-channel-number = <0x68>;
+ };
+
+ chan@8 {
+ label = "die_temp";
+ reg = <8>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "absolute";
+ qcom,scale-function = <3>;
+ qcom,hw-settle-time = <0>;
+ qcom,fast-avg-setup = <3>;
+ qcom,btm-channel-number = <0x70>;
+ };
+
+ chan@6 {
+ label = "vbat_sns";
+ reg = <6>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <1>;
+ qcom,calibration-type = "absolute";
+ qcom,scale-function = <0>;
+ qcom,hw-settle-time = <0>;
+ qcom,fast-avg-setup = <3>;
+ qcom,btm-channel-number = <0x78>;
+ };
+
+ chan@b5 {
+ label = "pa_therm0";
+ reg = <0xb5>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <2>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <3>;
+ qcom,btm-channel-number = <0x80>;
+ qcom,thermal-node;
+ };
+
+ chan@b7 {
+ label = "pa_therm1";
+ reg = <0xb7>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <2>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <3>;
+ qcom,btm-channel-number = <0x88>;
+ qcom,thermal-node;
+ };
+
+ chan@b4 {
+ label = "emmc_therm";
+ reg = <0xb4>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <2>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <3>;
+ qcom,btm-channel-number = <0x90>;
+ qcom,thermal-node;
+ };
+
+ chan@b3 {
+ label = "msm_therm";
+ reg = <0xb3>;
+ qcom,decimation = <0>;
+ qcom,pre-div-channel-scaling = <0>;
+ qcom,calibration-type = "ratiometric";
+ qcom,scale-function = <2>;
+ qcom,hw-settle-time = <2>;
+ qcom,fast-avg-setup = <3>;
+ qcom,btm-channel-number = <0x98>;
+ qcom,thermal-node;
+ };
+ };
+};
+
+&pm8941_lsid1 {
+ spmi-slave-container;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ regulator@1400 {
+ regulator-name = "8941_s1";
+ spmi-dev-container;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "qcom,qpnp-regulator";
+ reg = <0x1400 0x300>;
+ status = "disabled";
+
+ qcom,ctl@1400 {
+ reg = <0x1400 0x100>;
+ };
+ qcom,ps@1500 {
+ reg = <0x1500 0x100>;
+ };
+ qcom,freq@1600 {
+ reg = <0x1600 0x100>;
+ };
+ };
+
+ regulator@1700 {
+ regulator-name = "8941_s2";
+ spmi-dev-container;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "qcom,qpnp-regulator";
+ reg = <0x1700 0x300>;
+ status = "disabled";
+
+ qcom,ctl@1700 {
+ reg = <0x1700 0x100>;
+ };
+ qcom,ps@1800 {
+ reg = <0x1800 0x100>;
+ };
+ qcom,freq@1900 {
+ reg = <0x1900 0x100>;
+ };
+ };
+
+ regulator@1a00 {
+ regulator-name = "8941_s3";
+ spmi-dev-container;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "qcom,qpnp-regulator";
+ reg = <0x1a00 0x300>;
+ status = "disabled";
+
+ qcom,ctl@1a00 {
+ reg = <0x1a00 0x100>;
+ };
+ qcom,ps@1b00 {
+ reg = <0x1b00 0x100>;
+ };
+ qcom,freq@1c00 {
+ reg = <0x1c00 0x100>;
+ };
+ };
+
+ regulator@a000 {
+ regulator-name = "8941_boost";
+ reg = <0xa000 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@4000 {
+ regulator-name = "8941_l1";
+ reg = <0x4000 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@4100 {
+ regulator-name = "8941_l2";
+ reg = <0x4100 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@4200 {
+ regulator-name = "8941_l3";
+ reg = <0x4200 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@4300 {
+ regulator-name = "8941_l4";
+ reg = <0x4300 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@4400 {
+ regulator-name = "8941_l5";
+ reg = <0x4400 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ qcom,force-type = <0x04 0x10>;
+ status = "disabled";
+ };
+
+ regulator@4500 {
+ regulator-name = "8941_l6";
+ reg = <0x4500 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@4600 {
+ regulator-name = "8941_l7";
+ reg = <0x4600 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ qcom,force-type = <0x04 0x10>;
+ status = "disabled";
+ };
+
+ regulator@4700 {
+ regulator-name = "8941_l8";
+ reg = <0x4700 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@4800 {
+ regulator-name = "8941_l9";
+ reg = <0x4800 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@4900 {
+ regulator-name = "8941_l10";
+ reg = <0x4900 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@4a00 {
+ regulator-name = "8941_l11";
+ reg = <0x4a00 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@4b00 {
+ regulator-name = "8941_l12";
+ reg = <0x4b00 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@4c00 {
+ regulator-name = "8941_l13";
+ reg = <0x4c00 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@4d00 {
+ regulator-name = "8941_l14";
+ reg = <0x4d00 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@4e00 {
+ regulator-name = "8941_l15";
+ reg = <0x4e00 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@4f00 {
+ regulator-name = "8941_l16";
+ reg = <0x4f00 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@5000 {
+ regulator-name = "8941_l17";
+ reg = <0x5000 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@5100 {
+ regulator-name = "8941_l18";
+ reg = <0x5100 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@5200 {
+ regulator-name = "8941_l19";
+ reg = <0x5200 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@5300 {
+ regulator-name = "8941_l20";
+ reg = <0x5300 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@5400 {
+ regulator-name = "8941_l21";
+ reg = <0x5400 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@5500 {
+ regulator-name = "8941_l22";
+ reg = <0x5500 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@5600 {
+ regulator-name = "8941_l23";
+ reg = <0x5600 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@5700 {
+ regulator-name = "8941_l24";
+ reg = <0x5700 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@8000 {
+ regulator-name = "8941_lvs1";
+ reg = <0x8000 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@8100 {
+ regulator-name = "8941_lvs2";
+ reg = <0x8100 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@8200 {
+ regulator-name = "8941_lvs3";
+ reg = <0x8200 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@8300 {
+ regulator-name = "8941_mvs1";
+ reg = <0x8300 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ regulator@8400 {
+ regulator-name = "8941_mvs2";
+ reg = <0x8400 0x100>;
+ compatible = "qcom,qpnp-regulator";
+ status = "disabled";
+ };
+
+ qcom,vibrator@c000 {
+ compatible = "qcom,qpnp-vibrator";
+ reg = <0xc000 0x100>;
+ label = "vibrator";
+ status = "disabled";
+ };
+
+ qcom,leds@d000 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xd000 0x100>;
+ label = "rgb";
+ };
+
+ qcom,leds@d100 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xd100 0x100>;
+ label = "rgb";
+ };
+
+ qcom,leds@d200 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xd200 0x100>;
+ label = "rgb";
+ };
+
+ qcom,leds@d300 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xd300 0x100>;
+ label = "flash";
+ flash_boost-supply = <&pm8941_chg_boost>;
+ };
+
+ qcom,leds@d400 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xd400 0x100>;
+ label = "flash";
+ };
+
+ qcom,leds@d500 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xd500 0x100>;
+ label = "flash";
+ };
+
+ qcom,leds@d600 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xd600 0x100>;
+ label = "flash";
+ };
+
+ qcom,leds@d700 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xd700 0x100>;
+ label = "flash";
+ };
+
+ qcom,leds@d800 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xd800 0x100>;
+ label = "wled";
+ };
+
+ qcom,leds@d900 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xd900 0x100>;
+ label = "wled";
+ };
+
+ qcom,leds@da00 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xda00 0x100>;
+ label = "wled";
+ };
+
+ qcom,leds@db00 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xdb00 0x100>;
+ label = "wled";
+ };
+
+ qcom,leds@dc00 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xdc00 0x100>;
+ label = "wled";
+ };
+
+ qcom,leds@dd00 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xdd00 0x100>;
+ label = "wled";
+ };
+
+ qcom,leds@de00 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xde00 0x100>;
+ label = "wled";
+ };
+
+ qcom,leds@df00 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xdf00 0x100>;
+ label = "wled";
+ };
+
+ qcom,leds@e000 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xe000 0x100>;
+ label = "wled";
+ };
+
+ qcom,leds@e100 {
+ compatible = "qcom,leds-qpnp";
+ reg = <0xe100 0x100>;
+ label = "wled";
+ };
+
+ pwm@b100 {
+ compatible = "qcom,qpnp-pwm";
+ reg = <0xb100 0x100>,
+ <0xb042 0x7e>;
+ reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
+ qcom,channel-id = <0>;
+ };
+
+ pwm@b200 {
+ compatible = "qcom,qpnp-pwm";
+ reg = <0xb200 0x100>,
+ <0xb042 0x7e>;
+ reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
+ qcom,channel-id = <1>;
+ };
+
+ pwm@b300 {
+ compatible = "qcom,qpnp-pwm";
+ reg = <0xb300 0x100>,
+ <0xb042 0x7e>;
+ reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
+ qcom,channel-id = <2>;
+ };
+
+ pwm@b400 {
+ compatible = "qcom,qpnp-pwm";
+ reg = <0xb400 0x100>,
+ <0xb042 0x7e>;
+ reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
+ qcom,channel-id = <3>;
+ };
+
+ pwm@b500 {
+ compatible = "qcom,qpnp-pwm";
+ reg = <0xb500 0x100>,
+ <0xb042 0x7e>;
+ reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
+ qcom,channel-id = <4>;
+ };
+
+ pwm@b600 {
+ compatible = "qcom,qpnp-pwm";
+ reg = <0xb600 0x100>,
+ <0xb042 0x7e>;
+ reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
+ qcom,channel-id = <5>;
+ };
+
+ pwm@b700 {
+ compatible = "qcom,qpnp-pwm";
+ reg = <0xb700 0x100>,
+ <0xb042 0x7e>;
+ reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
+ qcom,channel-id = <6>;
+ };
+
+ pwm@b800 {
+ compatible = "qcom,qpnp-pwm";
+ reg = <0xb800 0x100>,
+ <0xb042 0x7e>;
+ reg-names = "qpnp-lpg-channel-base", "qpnp-lpg-lut-base";
+ qcom,channel-id = <7>;
};
};
diff --git a/arch/arm/boot/dts/msm8974-cdp.dtsi b/arch/arm/boot/dts/msm8974-cdp.dtsi
index bcdaf1b..8a3a77e 100644
--- a/arch/arm/boot/dts/msm8974-cdp.dtsi
+++ b/arch/arm/boot/dts/msm8974-cdp.dtsi
@@ -252,63 +252,61 @@
};
};
-&spmi_bus {
- qcom,pm8941@1 {
- qcom,leds@d800 {
- status = "okay";
- qcom,wled_0 {
- label = "wled";
- linux,name = "wled:backlight";
- linux,default-trigger = "bkl-trigger";
- qcom,cs-out-en;
- qcom,op-fdbck = <1>;
- qcom,default-state = "on";
- qcom,max-current = <25>;
- qcom,ctrl-delay-us = <0>;
- qcom,boost-curr-lim = <3>;
- qcom,cp-sel = <0>;
- qcom,switch-freq = <2>;
- qcom,ovp-val = <2>;
- qcom,num-strings = <1>;
- qcom,id = <0>;
- };
+&pm8941_lsid1 {
+ qcom,leds@d800 {
+ status = "okay";
+ qcom,wled_0 {
+ label = "wled";
+ linux,name = "wled:backlight";
+ linux,default-trigger = "bkl-trigger";
+ qcom,cs-out-en;
+ qcom,op-fdbck = <1>;
+ qcom,default-state = "on";
+ qcom,max-current = <25>;
+ qcom,ctrl-delay-us = <0>;
+ qcom,boost-curr-lim = <3>;
+ qcom,cp-sel = <0>;
+ qcom,switch-freq = <2>;
+ qcom,ovp-val = <2>;
+ qcom,num-strings = <1>;
+ qcom,id = <0>;
};
+ };
- qcom,leds@d900 {
- status = "disabled";
- };
+ qcom,leds@d900 {
+ status = "disabled";
+ };
- qcom,leds@da00 {
- status = "disabled";
- };
+ qcom,leds@da00 {
+ status = "disabled";
+ };
- qcom,leds@db00 {
- status = "disabled";
- };
+ qcom,leds@db00 {
+ status = "disabled";
+ };
- qcom,leds@dc00 {
- status = "disabled";
- };
+ qcom,leds@dc00 {
+ status = "disabled";
+ };
- qcom,leds@dd00 {
- status = "disabled";
- };
+ qcom,leds@dd00 {
+ status = "disabled";
+ };
- qcom,leds@de00 {
- status = "disabled";
- };
+ qcom,leds@de00 {
+ status = "disabled";
+ };
- qcom,leds@df00 {
- status = "disabled";
- };
+ qcom,leds@df00 {
+ status = "disabled";
+ };
- qcom,leds@e000 {
- status = "disabled";
- };
+ qcom,leds@e000 {
+ status = "disabled";
+ };
- qcom,leds@e100 {
- status = "disabled";
- };
+ qcom,leds@e100 {
+ status = "disabled";
};
};
diff --git a/arch/arm/boot/dts/msm8974-clock.dtsi b/arch/arm/boot/dts/msm8974-clock.dtsi
index bed5d70..8d90771 100644
--- a/arch/arm/boot/dts/msm8974-clock.dtsi
+++ b/arch/arm/boot/dts/msm8974-clock.dtsi
@@ -1,4 +1,4 @@
-/* Copyright (c) 2012, The Linux Foundation. All rights reserved.
+/* Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
@@ -10,18 +10,14 @@
* GNU General Public License for more details.
*/
-&spmi_bus {
+&pm8941_lsid0 {
+ pm8941_clkdiv1: clkdiv@5b00 {
+ qcom,cxo-div = <2>;
+ };
- qcom,pm8941@0 {
+ pm8941_clkdiv2: clkdiv@5c00 {
+ };
- pm8941_clkdiv1: clkdiv@5b00 {
- qcom,cxo-div = <2>;
- };
-
- pm8941_clkdiv2: clkdiv@5c00 {
- };
-
- pm8941_clkdiv3: clkdiv@5d00 {
- };
+ pm8941_clkdiv3: clkdiv@5d00 {
};
};
diff --git a/arch/arm/boot/dts/msm8974-fluid.dtsi b/arch/arm/boot/dts/msm8974-fluid.dtsi
index 638e6dd..57ce130 100644
--- a/arch/arm/boot/dts/msm8974-fluid.dtsi
+++ b/arch/arm/boot/dts/msm8974-fluid.dtsi
@@ -251,63 +251,61 @@
};
};
-&spmi_bus {
- qcom,pm8941@1 {
- qcom,leds@d800 {
- status = "okay";
- qcom,wled_0 {
- label = "wled";
- linux,name = "wled:backlight";
- linux,default-trigger = "bkl-trigger";
- qcom,cs-out-en;
- qcom,op-fdbck = <1>;
- qcom,default-state = "on";
- qcom,max-current = <25>;
- qcom,ctrl-delay-us = <0>;
- qcom,boost-curr-lim = <3>;
- qcom,cp-sel = <0>;
- qcom,switch-freq = <2>;
- qcom,ovp-val = <2>;
- qcom,num-strings = <1>;
- qcom,id = <0>;
- };
+&pm8941_lsid1 {
+ qcom,leds@d800 {
+ status = "okay";
+ qcom,wled_0 {
+ label = "wled";
+ linux,name = "wled:backlight";
+ linux,default-trigger = "bkl-trigger";
+ qcom,cs-out-en;
+ qcom,op-fdbck = <1>;
+ qcom,default-state = "on";
+ qcom,max-current = <25>;
+ qcom,ctrl-delay-us = <0>;
+ qcom,boost-curr-lim = <3>;
+ qcom,cp-sel = <0>;
+ qcom,switch-freq = <2>;
+ qcom,ovp-val = <2>;
+ qcom,num-strings = <1>;
+ qcom,id = <0>;
};
+ };
- qcom,leds@d900 {
- status = "disabled";
- };
+ qcom,leds@d900 {
+ status = "disabled";
+ };
- qcom,leds@da00 {
- status = "disabled";
- };
+ qcom,leds@da00 {
+ status = "disabled";
+ };
- qcom,leds@db00 {
- status = "disabled";
- };
+ qcom,leds@db00 {
+ status = "disabled";
+ };
- qcom,leds@dc00 {
- status = "disabled";
- };
+ qcom,leds@dc00 {
+ status = "disabled";
+ };
- qcom,leds@dd00 {
- status = "disabled";
- };
+ qcom,leds@dd00 {
+ status = "disabled";
+ };
- qcom,leds@de00 {
- status = "disabled";
- };
+ qcom,leds@de00 {
+ status = "disabled";
+ };
- qcom,leds@df00 {
- status = "disabled";
- };
+ qcom,leds@df00 {
+ status = "disabled";
+ };
- qcom,leds@e000 {
- status = "disabled";
- };
+ qcom,leds@e000 {
+ status = "disabled";
+ };
- qcom,leds@e100 {
- status = "disabled";
- };
+ qcom,leds@e100 {
+ status = "disabled";
};
};
diff --git a/arch/arm/boot/dts/msm8974-leds.dtsi b/arch/arm/boot/dts/msm8974-leds.dtsi
index 5e91f45..ab57468 100644
--- a/arch/arm/boot/dts/msm8974-leds.dtsi
+++ b/arch/arm/boot/dts/msm8974-leds.dtsi
@@ -11,119 +11,116 @@
* GNU General Public License for more details.
*/
-&spmi_bus {
- qcom,pm8941@1 {
- qcom,leds@d000 {
- status = "okay";
- qcom,rgb_0 {
- label = "rgb";
- linux,name = "led:rgb_red";
- qcom,mode = "pwm";
- qcom,pwm-channel = <6>;
- qcom,pwm-us = <1000>;
- qcom,max-current = <12>;
- qcom,default-state = "off";
- qcom,id = <3>;
- linux,default-trigger =
- "battery-charging";
- };
-
- qcom,rgb_1 {
- label = "rgb";
- linux,name = "led:rgb_green";
- qcom,mode = "pwm";
- qcom,pwm-channel = <5>;
- qcom,pwm-us = <1000>;
- qcom,max-current = <12>;
- qcom,default-state = "off";
- qcom,id = <4>;
- linux,default-trigger = "battery-full";
- };
-
- qcom,rgb_2 {
- label = "rgb";
- linux,name = "led:rgb_blue";
- qcom,mode = "pwm";
- qcom,pwm-channel = <4>;
- qcom,pwm-us = <1000>;
- qcom,max-current = <12>;
- qcom,id = <5>;
- status = "disabled";
- };
+&pm8941_lsid1 {
+ qcom,leds@d000 {
+ status = "okay";
+ qcom,rgb_0 {
+ label = "rgb";
+ linux,name = "led:rgb_red";
+ qcom,mode = "pwm";
+ qcom,pwm-channel = <6>;
+ qcom,pwm-us = <1000>;
+ qcom,max-current = <12>;
+ qcom,default-state = "off";
+ qcom,id = <3>;
+ linux,default-trigger =
+ "battery-charging";
};
- qcom,leds@d100 {
- status = "disabled";
+ qcom,rgb_1 {
+ label = "rgb";
+ linux,name = "led:rgb_green";
+ qcom,mode = "pwm";
+ qcom,pwm-channel = <5>;
+ qcom,pwm-us = <1000>;
+ qcom,max-current = <12>;
+ qcom,default-state = "off";
+ qcom,id = <4>;
+ linux,default-trigger = "battery-full";
};
- qcom,leds@d200 {
- status = "disabled";
- };
-
- qcom,leds@d300 {
- status = "okay";
- pm8941_flash0: qcom,flash_0 {
- qcom,max-current = <1000>;
- qcom,default-state = "off";
- qcom,headroom = <3>;
- qcom,duration = <1280>;
- qcom,clamp-curr = <200>;
- qcom,startup-dly = <3>;
- qcom,safety-timer;
- label = "flash";
- linux,default-trigger =
- "flash0_trigger";
- qcom,id = <1>;
- linux,name = "led:flash_0";
- qcom,current = <625>;
- };
-
- pm8941_flash1: qcom,flash_1 {
- qcom,max-current = <1000>;
- qcom,default-state = "off";
- qcom,headroom = <3>;
- qcom,duration = <1280>;
- qcom,clamp-curr = <200>;
- qcom,startup-dly = <3>;
- qcom,safety-timer;
- linux,default-trigger =
- "flash1_trigger";
- label = "flash";
- qcom,id = <2>;
- linux,name = "led:flash_1";
- qcom,current = <625>;
- };
-
- pm8941_torch: qcom,flash_torch {
- qcom,max-current = <200>;
- qcom,default-state = "off";
- qcom,headroom = <0>;
- qcom,startup-dly = <1>;
- linux,default-trigger =
- "torch_trigger";
- label = "flash";
- qcom,id = <2>;
- linux,name = "led:flash_torch";
- qcom,current = <200>;
- qcom,torch-enable;
- };
- };
-
- qcom,leds@d400 {
- status = "disabled";
- };
-
- qcom,leds@d500 {
- status = "disabled";
- };
-
- qcom,leds@d600 {
- status = "disabled";
- };
-
- qcom,leds@d700 {
+ qcom,rgb_2 {
+ label = "rgb";
+ linux,name = "led:rgb_blue";
+ qcom,mode = "pwm";
+ qcom,pwm-channel = <4>;
+ qcom,pwm-us = <1000>;
+ qcom,max-current = <12>;
+ qcom,id = <5>;
status = "disabled";
};
};
-};
+ qcom,leds@d100 {
+ status = "disabled";
+ };
+
+ qcom,leds@d200 {
+ status = "disabled";
+ };
+
+ qcom,leds@d300 {
+ status = "okay";
+ pm8941_flash0: qcom,flash_0 {
+ qcom,max-current = <1000>;
+ qcom,default-state = "off";
+ qcom,headroom = <3>;
+ qcom,duration = <1280>;
+ qcom,clamp-curr = <200>;
+ qcom,startup-dly = <3>;
+ qcom,safety-timer;
+ label = "flash";
+ linux,default-trigger =
+ "flash0_trigger";
+ qcom,id = <1>;
+ linux,name = "led:flash_0";
+ qcom,current = <625>;
+ };
+
+ pm8941_flash1: qcom,flash_1 {
+ qcom,max-current = <1000>;
+ qcom,default-state = "off";
+ qcom,headroom = <3>;
+ qcom,duration = <1280>;
+ qcom,clamp-curr = <200>;
+ qcom,startup-dly = <3>;
+ qcom,safety-timer;
+ linux,default-trigger =
+ "flash1_trigger";
+ label = "flash";
+ qcom,id = <2>;
+ linux,name = "led:flash_1";
+ qcom,current = <625>;
+ };
+
+ pm8941_torch: qcom,flash_torch {
+ qcom,max-current = <200>;
+ qcom,default-state = "off";
+ qcom,headroom = <0>;
+ qcom,startup-dly = <1>;
+ linux,default-trigger =
+ "torch_trigger";
+ label = "flash";
+ qcom,id = <2>;
+ linux,name = "led:flash_torch";
+ qcom,current = <200>;
+ qcom,torch-enable;
+ };
+ };
+
+ qcom,leds@d400 {
+ status = "disabled";
+ };
+
+ qcom,leds@d500 {
+ status = "disabled";
+ };
+
+ qcom,leds@d600 {
+ status = "disabled";
+ };
+
+ qcom,leds@d700 {
+ status = "disabled";
+ };
+};
diff --git a/arch/arm/boot/dts/msm8974-liquid.dtsi b/arch/arm/boot/dts/msm8974-liquid.dtsi
index ddf5b60..82bb7dc 100644
--- a/arch/arm/boot/dts/msm8974-liquid.dtsi
+++ b/arch/arm/boot/dts/msm8974-liquid.dtsi
@@ -782,14 +782,12 @@
};
};
-&spmi_bus {
- qcom,pm8941@1 {
- qcom,leds@d000 {
- qcom,rgb_2 {
- status = "ok";
- qcom,default-state = "on";
- qcom,turn-off-delay-ms = <1000>;
- };
+&pm8941_lsid1 {
+ qcom,leds@d000 {
+ qcom,rgb_2 {
+ status = "ok";
+ qcom,default-state = "on";
+ qcom,turn-off-delay-ms = <1000>;
};
};
};
diff --git a/arch/arm/boot/dts/msm8974-mtp.dtsi b/arch/arm/boot/dts/msm8974-mtp.dtsi
index 4af48cc..833ef48 100644
--- a/arch/arm/boot/dts/msm8974-mtp.dtsi
+++ b/arch/arm/boot/dts/msm8974-mtp.dtsi
@@ -192,63 +192,61 @@
};
};
-&spmi_bus {
- qcom,pm8941@1 {
- qcom,leds@d800 {
- status = "okay";
- qcom,wled_0 {
- label = "wled";
- linux,name = "wled:backlight";
- linux,default-trigger = "bkl-trigger";
- qcom,cs-out-en;
- qcom,op-fdbck = <1>;
- qcom,default-state = "on";
- qcom,max-current = <25>;
- qcom,ctrl-delay-us = <0>;
- qcom,boost-curr-lim = <3>;
- qcom,cp-sel = <0>;
- qcom,switch-freq = <2>;
- qcom,ovp-val = <2>;
- qcom,num-strings = <1>;
- qcom,id = <0>;
- };
+&pm8941_lsid1 {
+ qcom,leds@d800 {
+ status = "okay";
+ qcom,wled_0 {
+ label = "wled";
+ linux,name = "wled:backlight";
+ linux,default-trigger = "bkl-trigger";
+ qcom,cs-out-en;
+ qcom,op-fdbck = <1>;
+ qcom,default-state = "on";
+ qcom,max-current = <25>;
+ qcom,ctrl-delay-us = <0>;
+ qcom,boost-curr-lim = <3>;
+ qcom,cp-sel = <0>;
+ qcom,switch-freq = <2>;
+ qcom,ovp-val = <2>;
+ qcom,num-strings = <1>;
+ qcom,id = <0>;
};
+ };
- qcom,leds@d900 {
- status = "disabled";
- };
+ qcom,leds@d900 {
+ status = "disabled";
+ };
- qcom,leds@da00 {
- status = "disabled";
- };
+ qcom,leds@da00 {
+ status = "disabled";
+ };
- qcom,leds@db00 {
- status = "disabled";
- };
+ qcom,leds@db00 {
+ status = "disabled";
+ };
- qcom,leds@dc00 {
- status = "disabled";
- };
+ qcom,leds@dc00 {
+ status = "disabled";
+ };
- qcom,leds@dd00 {
- status = "disabled";
- };
+ qcom,leds@dd00 {
+ status = "disabled";
+ };
- qcom,leds@de00 {
- status = "disabled";
- };
+ qcom,leds@de00 {
+ status = "disabled";
+ };
- qcom,leds@df00 {
- status = "disabled";
- };
+ qcom,leds@df00 {
+ status = "disabled";
+ };
- qcom,leds@e000 {
- status = "disabled";
- };
+ qcom,leds@e000 {
+ status = "disabled";
+ };
- qcom,leds@e100 {
- status = "disabled";
- };
+ qcom,leds@e100 {
+ status = "disabled";
};
};
diff --git a/arch/arm/boot/dts/msm8974-regulator.dtsi b/arch/arm/boot/dts/msm8974-regulator.dtsi
index d9d5aaa..eae9032 100644
--- a/arch/arm/boot/dts/msm8974-regulator.dtsi
+++ b/arch/arm/boot/dts/msm8974-regulator.dtsi
@@ -13,48 +13,44 @@
/* QPNP controlled regulators: */
-&spmi_bus {
+&pm8941_lsid1 {
+ pm8941_boost: regulator@a000 {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ qcom,enable-time = <500>;
+ status = "okay";
+ };
- qcom,pm8941@1 {
+ pm8941_mvs1: regulator@8300 {
+ parent-supply = <&pm8941_chg_otg>;
+ qcom,enable-time = <1000>;
+ qcom,pull-down-enable = <1>;
+ interrupts = <0x1 0x83 0x2>;
+ interrupt-names = "ocp";
+ qcom,ocp-enable = <1>;
+ qcom,ocp-max-retries = <10>;
+ qcom,ocp-retry-delay = <30>;
+ qcom,soft-start-enable = <1>;
+ qcom,vs-soft-start-strength = <0>;
+ qcom,hpm-enable = <1>;
+ qcom,auto-mode-enable = <0>;
+ status = "okay";
+ };
- pm8941_boost: regulator@a000 {
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- qcom,enable-time = <500>;
- status = "okay";
- };
-
- pm8941_mvs1: regulator@8300 {
- parent-supply = <&pm8941_chg_otg>;
- qcom,enable-time = <1000>;
- qcom,pull-down-enable = <1>;
- interrupts = <0x1 0x83 0x2>;
- interrupt-names = "ocp";
- qcom,ocp-enable = <1>;
- qcom,ocp-max-retries = <10>;
- qcom,ocp-retry-delay = <30>;
- qcom,soft-start-enable = <1>;
- qcom,vs-soft-start-strength = <0>;
- qcom,hpm-enable = <1>;
- qcom,auto-mode-enable = <0>;
- status = "okay";
- };
-
- pm8941_mvs2: regulator@8400 {
- parent-supply = <&pm8941_boost>;
- qcom,enable-time = <1000>;
- qcom,pull-down-enable = <1>;
- interrupts = <0x1 0x84 0x2>;
- interrupt-names = "ocp";
- qcom,ocp-enable = <1>;
- qcom,ocp-max-retries = <10>;
- qcom,ocp-retry-delay = <30>;
- qcom,soft-start-enable = <1>;
- qcom,vs-soft-start-strength = <0>;
- qcom,hpm-enable = <1>;
- qcom,auto-mode-enable = <0>;
- status = "okay";
- };
+ pm8941_mvs2: regulator@8400 {
+ parent-supply = <&pm8941_boost>;
+ qcom,enable-time = <1000>;
+ qcom,pull-down-enable = <1>;
+ interrupts = <0x1 0x84 0x2>;
+ interrupt-names = "ocp";
+ qcom,ocp-enable = <1>;
+ qcom,ocp-max-retries = <10>;
+ qcom,ocp-retry-delay = <30>;
+ qcom,soft-start-enable = <1>;
+ qcom,vs-soft-start-strength = <0>;
+ qcom,hpm-enable = <1>;
+ qcom,auto-mode-enable = <0>;
+ status = "okay";
};
};
diff --git a/arch/arm/boot/dts/msm8974.dtsi b/arch/arm/boot/dts/msm8974.dtsi
index 181eb9a..7641568 100644
--- a/arch/arm/boot/dts/msm8974.dtsi
+++ b/arch/arm/boot/dts/msm8974.dtsi
@@ -1693,6 +1693,14 @@
/include/ "msm-pm8x41-rpm-regulator.dtsi"
/include/ "msm-pm8841.dtsi"
+&spmi_bus {
+ pm8941_lsid0: qcom,pm8941@0 {
+ reg = <0x0>;
+ };
+ pm8941_lsid1: qcom,pm8941@1 {
+ reg = <0x1>;
+ };
+};
/include/ "msm-pm8941.dtsi"
/include/ "msm8974-regulator.dtsi"
/include/ "msm8974-clock.dtsi"