arm/dt: camera: Update dt entries for camera sensor drivers
Add camera sensor device id address and id value in dt instead of
putting in camera sensor driver.
Change-Id: I5f14b2d956795216f2261aa1c111cb4c00a3107e
Signed-off-by: Hody Hung <hhung@codeaurora.org>
Signed-off-by: Shuzhen Wang <shuzhenw@codeaurora.org>
diff --git a/arch/arm/boot/dts/msm8974-camera-sensor.dtsi b/arch/arm/boot/dts/msm8974-camera-sensor.dtsi
index 68da844..948cdf5 100644
--- a/arch/arm/boot/dts/msm8974-camera-sensor.dtsi
+++ b/arch/arm/boot/dts/msm8974-camera-sensor.dtsi
@@ -1,5 +1,5 @@
/*
- * Copyright (c) 2012, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
@@ -16,8 +16,9 @@
qcom,camera@6e {
compatible = "qcom,s5k3l1yx";
reg = <0x6e 0x0>;
- qcom,csi-if = <1>;
- qcom,csid-core = <0>;
+ qcom,slave-id = <0x6e 0x0 0x3121>;
+ qcom,csiphy-sd-index = <0>;
+ qcom,csid-sd-index = <0>;
qcom,flash-src-index = <&led_flash0>;
qcom,mount-angle = <90>;
qcom,sensor-name = "s5k3l1yx";
@@ -25,41 +26,37 @@
cam_vana-supply = <&pm8941_l17>;
cam_vio-supply = <&pm8941_lvs3>;
cam_vaf-supply = <&pm8941_l23>;
- qcom,cam-vreg-name = "cam_vdig", "cam_vana", "cam_vio",
+ qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana",
"cam_vaf";
- qcom,cam-vreg-type = <0 0 1 0>;
- qcom,cam-vreg-min-voltage = <1225000 2850000 0 3000000>;
- qcom,cam-vreg-max-voltage = <1225000 2850000 0 3000000>;
- qcom,cam-vreg-op-mode = <105000 80000 0 100000>;
+ qcom,cam-vreg-type = <0 1 0 0>;
+ qcom,cam-vreg-min-voltage = <1225000 0 2850000 3000000>;
+ qcom,cam-vreg-max-voltage = <1225000 0 2850000 3000000>;
+ qcom,cam-vreg-op-mode = <105000 0 80000 100000>;
qcom,gpio-no-mux = <0>;
gpios = <&msmgpio 15 0>,
- <&msmgpio 19 0>,
- <&msmgpio 20 0>,
<&msmgpio 90 0>;
- qcom,gpio-common-tbl-num = <0 1 2>;
- qcom,gpio-common-tbl-flags = <1 1 1>;
- qcom,gpio-common-tbl-label = "CAMIF_MCLK",
- "CAMIF_I2C_DATA",
- "CAMIF_I2C_CLK";
- qcom,gpio-req-tbl-num = <3>;
- qcom,gpio-req-tbl-flags = <0>;
- qcom,gpio-req-tbl-label = "CAM_RESET1";
- qcom,gpio-set-tbl-num = <3 3>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-req-tbl-num = <0 1>;
+ qcom,gpio-req-tbl-flags = <1 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK",
+ "CAM_RESET1";
+ qcom,gpio-set-tbl-num = <1 1>;
qcom,gpio-set-tbl-flags = <0 2>;
qcom,gpio-set-tbl-delay = <1000 30000>;
qcom,csi-lane-assign = <0x4320>;
qcom,csi-lane-mask = <0x1F>;
- qcom,csi-phy-sel = <0>;
- qcom,camera-type = <0>;
- qcom,sensor-type = <0>;
+ qcom,sensor-position = <0>;
+ qcom,sensor-mode = <1>;
status = "ok";
};
qcom,camera@6c {
compatible = "qcom,ov2720";
reg = <0x6c 0x0>;
- qcom,csi-if = <1>;
- qcom,csid-core = <0>;
+ qcom,slave-id = <0x6c 0x300A 0x2720>;
+ qcom,led-flash-sd-index = <0>;
+ qcom,csiphy-sd-index = <2>;
+ qcom,csid-sd-index = <0>;
qcom,mount-angle = <180>;
qcom,sensor-name = "ov2720";
cam_vdig-supply = <&pm8941_l3>;
@@ -72,25 +69,19 @@
qcom,cam-vreg-op-mode = <105000 80000 0>;
qcom,gpio-no-mux = <0>;
gpios = <&msmgpio 17 0>,
- <&msmgpio 19 0>,
- <&msmgpio 20 0>,
<&msmgpio 18 0>;
- qcom,gpio-common-tbl-num = <0 1 2>;
- qcom,gpio-common-tbl-flags = <1 1 1>;
- qcom,gpio-common-tbl-label = "CAMIF_MCLK",
- "CAMIF_I2C_DATA",
- "CAMIF_I2C_CLK";
- qcom,gpio-req-tbl-num = <3>;
- qcom,gpio-req-tbl-flags = <0>;
- qcom,gpio-req-tbl-label = "CAM_RESET1";
- qcom,gpio-set-tbl-num = <3 3>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-req-tbl-num = <0 1>;
+ qcom,gpio-req-tbl-flags = <1 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK",
+ "CAM_RESET1";
+ qcom,gpio-set-tbl-num = <1 1>;
qcom,gpio-set-tbl-flags = <0 2>;
qcom,gpio-set-tbl-delay = <1000 4000>;
qcom,csi-lane-assign = <0x4320>;
qcom,csi-lane-mask = <0x7>;
- qcom,csi-phy-sel = <2>;
- qcom,camera-type = <1>;
- qcom,sensor-type = <0>;
+ qcom,sensor-position = <1>;
+ qcom,sensor-mode = <1>;
status = "ok";
};
};