regulator: TPS65910: Fix VDD1/2 voltage selector count
Count of selector voltage is required for regulator_set_voltage
to work via set_voltage_sel. VDD1/2 currently have it as zero,
so regulator_set_voltage won't work for VDD1/2.
Update count (n_voltages) for VDD1/2.
Output Voltage = (step value * 12.5 mV + 562.5 mV) * gain
With above expr, number of voltages that can be selected is
step value count * gain count
constant for gain count will be called VDD1_2_NUM_VOLT_COARSE
existing constant for step value count is VDD1_2_NUM_VOLTS,
use VDD1_2_NUM_VOLT_FINE instead to make clear that step value
is not the only component in deciding selectable voltage count
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
diff --git a/drivers/regulator/tps65910-regulator.c b/drivers/regulator/tps65910-regulator.c
index 66d2d60..b552aae 100644
--- a/drivers/regulator/tps65910-regulator.c
+++ b/drivers/regulator/tps65910-regulator.c
@@ -664,10 +664,10 @@
switch (id) {
case TPS65910_REG_VDD1:
- dcdc_mult = (selector / VDD1_2_NUM_VOLTS) + 1;
+ dcdc_mult = (selector / VDD1_2_NUM_VOLT_FINE) + 1;
if (dcdc_mult == 1)
dcdc_mult--;
- vsel = (selector % VDD1_2_NUM_VOLTS) + 3;
+ vsel = (selector % VDD1_2_NUM_VOLT_FINE) + 3;
tps65910_modify_bits(pmic, TPS65910_VDD1,
(dcdc_mult << VDD1_VGAIN_SEL_SHIFT),
@@ -675,10 +675,10 @@
tps65910_reg_write(pmic, TPS65910_VDD1_OP, vsel);
break;
case TPS65910_REG_VDD2:
- dcdc_mult = (selector / VDD1_2_NUM_VOLTS) + 1;
+ dcdc_mult = (selector / VDD1_2_NUM_VOLT_FINE) + 1;
if (dcdc_mult == 1)
dcdc_mult--;
- vsel = (selector % VDD1_2_NUM_VOLTS) + 3;
+ vsel = (selector % VDD1_2_NUM_VOLT_FINE) + 3;
tps65910_modify_bits(pmic, TPS65910_VDD2,
(dcdc_mult << VDD2_VGAIN_SEL_SHIFT),
@@ -756,9 +756,9 @@
switch (id) {
case TPS65910_REG_VDD1:
case TPS65910_REG_VDD2:
- mult = (selector / VDD1_2_NUM_VOLTS) + 1;
+ mult = (selector / VDD1_2_NUM_VOLT_FINE) + 1;
volt = VDD1_2_MIN_VOLT +
- (selector % VDD1_2_NUM_VOLTS) * VDD1_2_OFFSET;
+ (selector % VDD1_2_NUM_VOLT_FINE) * VDD1_2_OFFSET;
break;
case TPS65911_REG_VDDCTRL:
volt = VDDCTRL_MIN_VOLT + (selector * VDDCTRL_OFFSET);
@@ -947,6 +947,8 @@
if (i == TPS65910_REG_VDD1 || i == TPS65910_REG_VDD2) {
pmic->desc[i].ops = &tps65910_ops_dcdc;
+ pmic->desc[i].n_voltages = VDD1_2_NUM_VOLT_FINE *
+ VDD1_2_NUM_VOLT_COARSE;
} else if (i == TPS65910_REG_VDD3) {
if (tps65910_chip_id(tps65910) == TPS65910)
pmic->desc[i].ops = &tps65910_ops_vdd3;