MIPS: Alchemy: update core interrupt code.
This patch attempts to modernize core Alchemy interrupt handling code.
- add irq_chips for irq controllers instead of irq type,
- add a set_type() hook to change irq trigger type during runtime,
- add a set_wake() hook to control GPIO0..7 based wakeup,
- use linux' IRQF_TRIGGER_ constants instead of homebrew ones,
- enable GENERIC_HARDIRQS_NO__DO_IRQ.
- simplify plat_irq_dispatch
- merge au1xxx_irqmap into irq.c file, the only place where its
contents are referenced.
- board_init_irq() is now mandatory for every board; use it to register
the remaining (gpio-based) interrupt sources; update all boards
accordingly.
Run-tested on Db1200 and other Au1200 based platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/au1xxx_irqmap.c
diff --git a/arch/mips/alchemy/common/irq.c b/arch/mips/alchemy/common/irq.c
index 40c6cec..c543847 100644
--- a/arch/mips/alchemy/common/irq.c
+++ b/arch/mips/alchemy/common/irq.c
@@ -24,6 +24,7 @@
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
+
#include <linux/bitops.h>
#include <linux/init.h>
#include <linux/interrupt.h>
@@ -36,16 +37,175 @@
#include <asm/mach-pb1x00/pb1000.h>
#endif
-#define EXT_INTC0_REQ0 2 /* IP 2 */
-#define EXT_INTC0_REQ1 3 /* IP 3 */
-#define EXT_INTC1_REQ0 4 /* IP 4 */
-#define EXT_INTC1_REQ1 5 /* IP 5 */
-#define MIPS_TIMER_IP 7 /* IP 7 */
-
-void (*board_init_irq)(void) __initdata = NULL;
-
static DEFINE_SPINLOCK(irq_lock);
+static int au1x_ic_settype(unsigned int irq, unsigned int flow_type);
+
+/* per-processor fixed function irqs */
+struct au1xxx_irqmap au1xxx_ic0_map[] __initdata = {
+
+#if defined(CONFIG_SOC_AU1000)
+ { AU1000_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_UART2_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_SSI0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_SSI1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+1, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+2, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+3, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+4, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+5, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+6, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+7, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
+ { AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_IRDA_TX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_IRDA_RX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1000_ACSYNC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_MAC1_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_AC97C_INT, IRQ_TYPE_EDGE_RISING, 0 },
+
+#elif defined(CONFIG_SOC_AU1500)
+
+ { AU1500_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_PCI_INTA, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1000_PCI_INTB, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1500_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_PCI_INTC, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1000_PCI_INTD, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1000_DMA_INT_BASE, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+1, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+2, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+3, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+4, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+5, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+6, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+7, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
+ { AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1000_ACSYNC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1500_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1500_MAC1_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_AC97C_INT, IRQ_TYPE_EDGE_RISING, 0 },
+
+#elif defined(CONFIG_SOC_AU1100)
+
+ { AU1100_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_SD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_SSI0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_SSI1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+1, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+2, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+3, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+4, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+5, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+6, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_DMA_INT_BASE+7, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
+ { AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_IRDA_TX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_IRDA_RX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1000_ACSYNC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1100_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1100_LCD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_AC97C_INT, IRQ_TYPE_EDGE_RISING, 0 },
+
+#elif defined(CONFIG_SOC_AU1550)
+
+ { AU1550_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_PCI_INTA, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1550_PCI_INTB, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1550_DDMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_CRYPTO_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_PCI_INTC, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1550_PCI_INTD, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1550_PCI_RST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1550_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_PSC0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_PSC1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_PSC2_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_PSC3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
+ { AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1550_NAND_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1550_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1550_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
+ { AU1550_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1550_MAC1_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+
+#elif defined(CONFIG_SOC_AU1200)
+
+ { AU1200_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_SWT_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1200_SD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_DDMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_MAE_BE_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_MAE_FE_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_PSC0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_PSC1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_AES_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_CAMERA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
+ { AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1200_NAND_INT, IRQ_TYPE_EDGE_RISING, 0 },
+ { AU1200_USB_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_LCD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+ { AU1200_MAE_BOTH_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+
+#else
+#error "Error: Unknown Alchemy SOC"
+#endif
+};
+
+
#ifdef CONFIG_PM
/*
@@ -130,67 +290,47 @@
#endif /* CONFIG_PM */
-inline void local_enable_irq(unsigned int irq_nr)
+static void au1x_ic0_unmask(unsigned int irq_nr)
{
unsigned int bit = irq_nr - AU1000_INTC0_INT_BASE;
-
- if (bit >= 32) {
- au_writel(1 << (bit - 32), IC1_MASKSET);
- au_writel(1 << (bit - 32), IC1_WAKESET);
- } else {
- au_writel(1 << bit, IC0_MASKSET);
- au_writel(1 << bit, IC0_WAKESET);
- }
+ au_writel(1 << bit, IC0_MASKSET);
+ au_writel(1 << bit, IC0_WAKESET);
au_sync();
}
-
-inline void local_disable_irq(unsigned int irq_nr)
+static void au1x_ic1_unmask(unsigned int irq_nr)
{
- unsigned int bit = irq_nr - AU1000_INTC0_INT_BASE;
+ unsigned int bit = irq_nr - AU1000_INTC1_INT_BASE;
+ au_writel(1 << bit, IC1_MASKSET);
+ au_writel(1 << bit, IC1_WAKESET);
- if (bit >= 32) {
- au_writel(1 << (bit - 32), IC1_MASKCLR);
- au_writel(1 << (bit - 32), IC1_WAKECLR);
- } else {
- au_writel(1 << bit, IC0_MASKCLR);
- au_writel(1 << bit, IC0_WAKECLR);
- }
+/* very hacky. does the pb1000 cpld auto-disable this int?
+ * nowhere in the current kernel sources is it disabled. --mlau
+ */
+#if defined(CONFIG_MIPS_PB1000)
+ if (irq_nr == AU1000_GPIO_15)
+ au_writel(0x4000, PB1000_MDR); /* enable int */
+#endif
au_sync();
}
-
-static inline void mask_and_ack_rise_edge_irq(unsigned int irq_nr)
+static void au1x_ic0_mask(unsigned int irq_nr)
{
unsigned int bit = irq_nr - AU1000_INTC0_INT_BASE;
-
- if (bit >= 32) {
- au_writel(1 << (bit - 32), IC1_RISINGCLR);
- au_writel(1 << (bit - 32), IC1_MASKCLR);
- } else {
- au_writel(1 << bit, IC0_RISINGCLR);
- au_writel(1 << bit, IC0_MASKCLR);
- }
+ au_writel(1 << bit, IC0_MASKCLR);
+ au_writel(1 << bit, IC0_WAKECLR);
au_sync();
}
-
-static inline void mask_and_ack_fall_edge_irq(unsigned int irq_nr)
+static void au1x_ic1_mask(unsigned int irq_nr)
{
- unsigned int bit = irq_nr - AU1000_INTC0_INT_BASE;
-
- if (bit >= 32) {
- au_writel(1 << (bit - 32), IC1_FALLINGCLR);
- au_writel(1 << (bit - 32), IC1_MASKCLR);
- } else {
- au_writel(1 << bit, IC0_FALLINGCLR);
- au_writel(1 << bit, IC0_MASKCLR);
- }
+ unsigned int bit = irq_nr - AU1000_INTC1_INT_BASE;
+ au_writel(1 << bit, IC1_MASKCLR);
+ au_writel(1 << bit, IC1_WAKECLR);
au_sync();
}
-
-static inline void mask_and_ack_either_edge_irq(unsigned int irq_nr)
+static void au1x_ic0_ack(unsigned int irq_nr)
{
unsigned int bit = irq_nr - AU1000_INTC0_INT_BASE;
@@ -198,349 +338,229 @@
* This may assume that we don't get interrupts from
* both edges at once, or if we do, that we don't care.
*/
- if (bit >= 32) {
- au_writel(1 << (bit - 32), IC1_FALLINGCLR);
- au_writel(1 << (bit - 32), IC1_RISINGCLR);
- au_writel(1 << (bit - 32), IC1_MASKCLR);
- } else {
- au_writel(1 << bit, IC0_FALLINGCLR);
- au_writel(1 << bit, IC0_RISINGCLR);
- au_writel(1 << bit, IC0_MASKCLR);
- }
+ au_writel(1 << bit, IC0_FALLINGCLR);
+ au_writel(1 << bit, IC0_RISINGCLR);
au_sync();
}
-static inline void mask_and_ack_level_irq(unsigned int irq_nr)
+static void au1x_ic1_ack(unsigned int irq_nr)
{
- local_disable_irq(irq_nr);
+ unsigned int bit = irq_nr - AU1000_INTC1_INT_BASE;
+
+ /*
+ * This may assume that we don't get interrupts from
+ * both edges at once, or if we do, that we don't care.
+ */
+ au_writel(1 << bit, IC1_FALLINGCLR);
+ au_writel(1 << bit, IC1_RISINGCLR);
au_sync();
-#if defined(CONFIG_MIPS_PB1000)
- if (irq_nr == AU1000_GPIO_15) {
- au_writel(0x8000, PB1000_MDR); /* ack int */
- au_sync();
- }
-#endif
}
-static void end_irq(unsigned int irq_nr)
+static int au1x_ic1_setwake(unsigned int irq, unsigned int on)
{
- if (!(irq_desc[irq_nr].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
- local_enable_irq(irq_nr);
+ unsigned int bit = irq - AU1000_INTC1_INT_BASE;
+ unsigned long wakemsk, flags;
-#if defined(CONFIG_MIPS_PB1000)
- if (irq_nr == AU1000_GPIO_15) {
- au_writel(0x4000, PB1000_MDR); /* enable int */
- au_sync();
- }
-#endif
-}
+ /* only GPIO 0-7 can act as wakeup source: */
+ if ((irq < AU1000_GPIO_0) || (irq > AU1000_GPIO_7))
+ return -EINVAL;
-unsigned long save_local_and_disable(int controller)
-{
- int i;
- unsigned long flags, mask;
-
- spin_lock_irqsave(&irq_lock, flags);
- if (controller) {
- mask = au_readl(IC1_MASKSET);
- for (i = 32; i < 64; i++)
- local_disable_irq(i);
- } else {
- mask = au_readl(IC0_MASKSET);
- for (i = 0; i < 32; i++)
- local_disable_irq(i);
- }
- spin_unlock_irqrestore(&irq_lock, flags);
-
- return mask;
-}
-
-void restore_local_and_enable(int controller, unsigned long mask)
-{
- int i;
- unsigned long flags, new_mask;
-
- spin_lock_irqsave(&irq_lock, flags);
- for (i = 0; i < 32; i++)
- if (mask & (1 << i)) {
- if (controller)
- local_enable_irq(i + 32);
- else
- local_enable_irq(i);
- }
-
- if (controller)
- new_mask = au_readl(IC1_MASKSET);
+ local_irq_save(flags);
+ wakemsk = au_readl(SYS_WAKEMSK);
+ if (on)
+ wakemsk |= 1 << bit;
else
- new_mask = au_readl(IC0_MASKSET);
-
- spin_unlock_irqrestore(&irq_lock, flags);
-}
-
-
-static struct irq_chip rise_edge_irq_type = {
- .name = "Au1000 Rise Edge",
- .ack = mask_and_ack_rise_edge_irq,
- .mask = local_disable_irq,
- .mask_ack = mask_and_ack_rise_edge_irq,
- .unmask = local_enable_irq,
- .end = end_irq,
-};
-
-static struct irq_chip fall_edge_irq_type = {
- .name = "Au1000 Fall Edge",
- .ack = mask_and_ack_fall_edge_irq,
- .mask = local_disable_irq,
- .mask_ack = mask_and_ack_fall_edge_irq,
- .unmask = local_enable_irq,
- .end = end_irq,
-};
-
-static struct irq_chip either_edge_irq_type = {
- .name = "Au1000 Rise or Fall Edge",
- .ack = mask_and_ack_either_edge_irq,
- .mask = local_disable_irq,
- .mask_ack = mask_and_ack_either_edge_irq,
- .unmask = local_enable_irq,
- .end = end_irq,
-};
-
-static struct irq_chip level_irq_type = {
- .name = "Au1000 Level",
- .ack = mask_and_ack_level_irq,
- .mask = local_disable_irq,
- .mask_ack = mask_and_ack_level_irq,
- .unmask = local_enable_irq,
- .end = end_irq,
-};
-
-static void __init setup_local_irq(unsigned int irq_nr, int type, int int_req)
-{
- unsigned int bit = irq_nr - AU1000_INTC0_INT_BASE;
-
- if (irq_nr > AU1000_MAX_INTR)
- return;
-
- /* Config2[n], Config1[n], Config0[n] */
- if (bit >= 32) {
- switch (type) {
- case INTC_INT_RISE_EDGE: /* 0:0:1 */
- au_writel(1 << (bit - 32), IC1_CFG2CLR);
- au_writel(1 << (bit - 32), IC1_CFG1CLR);
- au_writel(1 << (bit - 32), IC1_CFG0SET);
- set_irq_chip(irq_nr, &rise_edge_irq_type);
- break;
- case INTC_INT_FALL_EDGE: /* 0:1:0 */
- au_writel(1 << (bit - 32), IC1_CFG2CLR);
- au_writel(1 << (bit - 32), IC1_CFG1SET);
- au_writel(1 << (bit - 32), IC1_CFG0CLR);
- set_irq_chip(irq_nr, &fall_edge_irq_type);
- break;
- case INTC_INT_RISE_AND_FALL_EDGE: /* 0:1:1 */
- au_writel(1 << (bit - 32), IC1_CFG2CLR);
- au_writel(1 << (bit - 32), IC1_CFG1SET);
- au_writel(1 << (bit - 32), IC1_CFG0SET);
- set_irq_chip(irq_nr, &either_edge_irq_type);
- break;
- case INTC_INT_HIGH_LEVEL: /* 1:0:1 */
- au_writel(1 << (bit - 32), IC1_CFG2SET);
- au_writel(1 << (bit - 32), IC1_CFG1CLR);
- au_writel(1 << (bit - 32), IC1_CFG0SET);
- set_irq_chip(irq_nr, &level_irq_type);
- break;
- case INTC_INT_LOW_LEVEL: /* 1:1:0 */
- au_writel(1 << (bit - 32), IC1_CFG2SET);
- au_writel(1 << (bit - 32), IC1_CFG1SET);
- au_writel(1 << (bit - 32), IC1_CFG0CLR);
- set_irq_chip(irq_nr, &level_irq_type);
- break;
- case INTC_INT_DISABLED: /* 0:0:0 */
- au_writel(1 << (bit - 32), IC1_CFG0CLR);
- au_writel(1 << (bit - 32), IC1_CFG1CLR);
- au_writel(1 << (bit - 32), IC1_CFG2CLR);
- break;
- default: /* disable the interrupt */
- printk(KERN_WARNING "unexpected int type %d (irq %d)\n",
- type, irq_nr);
- au_writel(1 << (bit - 32), IC1_CFG0CLR);
- au_writel(1 << (bit - 32), IC1_CFG1CLR);
- au_writel(1 << (bit - 32), IC1_CFG2CLR);
- return;
- }
- if (int_req) /* assign to interrupt request 1 */
- au_writel(1 << (bit - 32), IC1_ASSIGNCLR);
- else /* assign to interrupt request 0 */
- au_writel(1 << (bit - 32), IC1_ASSIGNSET);
- au_writel(1 << (bit - 32), IC1_SRCSET);
- au_writel(1 << (bit - 32), IC1_MASKCLR);
- au_writel(1 << (bit - 32), IC1_WAKECLR);
- } else {
- switch (type) {
- case INTC_INT_RISE_EDGE: /* 0:0:1 */
- au_writel(1 << bit, IC0_CFG2CLR);
- au_writel(1 << bit, IC0_CFG1CLR);
- au_writel(1 << bit, IC0_CFG0SET);
- set_irq_chip(irq_nr, &rise_edge_irq_type);
- break;
- case INTC_INT_FALL_EDGE: /* 0:1:0 */
- au_writel(1 << bit, IC0_CFG2CLR);
- au_writel(1 << bit, IC0_CFG1SET);
- au_writel(1 << bit, IC0_CFG0CLR);
- set_irq_chip(irq_nr, &fall_edge_irq_type);
- break;
- case INTC_INT_RISE_AND_FALL_EDGE: /* 0:1:1 */
- au_writel(1 << bit, IC0_CFG2CLR);
- au_writel(1 << bit, IC0_CFG1SET);
- au_writel(1 << bit, IC0_CFG0SET);
- set_irq_chip(irq_nr, &either_edge_irq_type);
- break;
- case INTC_INT_HIGH_LEVEL: /* 1:0:1 */
- au_writel(1 << bit, IC0_CFG2SET);
- au_writel(1 << bit, IC0_CFG1CLR);
- au_writel(1 << bit, IC0_CFG0SET);
- set_irq_chip(irq_nr, &level_irq_type);
- break;
- case INTC_INT_LOW_LEVEL: /* 1:1:0 */
- au_writel(1 << bit, IC0_CFG2SET);
- au_writel(1 << bit, IC0_CFG1SET);
- au_writel(1 << bit, IC0_CFG0CLR);
- set_irq_chip(irq_nr, &level_irq_type);
- break;
- case INTC_INT_DISABLED: /* 0:0:0 */
- au_writel(1 << bit, IC0_CFG0CLR);
- au_writel(1 << bit, IC0_CFG1CLR);
- au_writel(1 << bit, IC0_CFG2CLR);
- break;
- default: /* disable the interrupt */
- printk(KERN_WARNING "unexpected int type %d (irq %d)\n",
- type, irq_nr);
- au_writel(1 << bit, IC0_CFG0CLR);
- au_writel(1 << bit, IC0_CFG1CLR);
- au_writel(1 << bit, IC0_CFG2CLR);
- return;
- }
- if (int_req) /* assign to interrupt request 1 */
- au_writel(1 << bit, IC0_ASSIGNCLR);
- else /* assign to interrupt request 0 */
- au_writel(1 << bit, IC0_ASSIGNSET);
- au_writel(1 << bit, IC0_SRCSET);
- au_writel(1 << bit, IC0_MASKCLR);
- au_writel(1 << bit, IC0_WAKECLR);
- }
+ wakemsk &= ~(1 << bit);
+ au_writel(wakemsk, SYS_WAKEMSK);
au_sync();
+ local_irq_restore(flags);
+
+ return 0;
}
/*
- * Interrupts are nested. Even if an interrupt handler is registered
- * as "fast", we might get another interrupt before we return from
- * intcX_reqX_irqdispatch().
+ * irq_chips for both ICs; this way the mask handlers can be
+ * as short as possible.
+ *
+ * NOTE: the ->ack() callback is used by the handle_edge_irq
+ * flowhandler only, the ->mask_ack() one by handle_level_irq,
+ * so no need for an irq_chip for each type of irq (level/edge).
*/
+static struct irq_chip au1x_ic0_chip = {
+ .name = "Alchemy-IC0",
+ .ack = au1x_ic0_ack, /* edge */
+ .mask = au1x_ic0_mask,
+ .mask_ack = au1x_ic0_mask, /* level */
+ .unmask = au1x_ic0_unmask,
+ .set_type = au1x_ic_settype,
+};
-static void intc0_req0_irqdispatch(void)
+static struct irq_chip au1x_ic1_chip = {
+ .name = "Alchemy-IC1",
+ .ack = au1x_ic1_ack, /* edge */
+ .mask = au1x_ic1_mask,
+ .mask_ack = au1x_ic1_mask, /* level */
+ .unmask = au1x_ic1_unmask,
+ .set_type = au1x_ic_settype,
+ .set_wake = au1x_ic1_setwake,
+};
+
+static int au1x_ic_settype(unsigned int irq, unsigned int flow_type)
{
- static unsigned long intc0_req0;
- unsigned int bit;
+ struct irq_chip *chip;
+ unsigned long icr[6];
+ unsigned int bit, ic;
+ int ret;
- intc0_req0 |= au_readl(IC0_REQ0INT);
+ if (irq >= AU1000_INTC1_INT_BASE) {
+ bit = irq - AU1000_INTC1_INT_BASE;
+ chip = &au1x_ic1_chip;
+ ic = 1;
+ } else {
+ bit = irq - AU1000_INTC0_INT_BASE;
+ chip = &au1x_ic0_chip;
+ ic = 0;
+ }
- if (!intc0_req0)
+ if (bit > 31)
+ return -EINVAL;
+
+ icr[0] = ic ? IC1_CFG0SET : IC0_CFG0SET;
+ icr[1] = ic ? IC1_CFG1SET : IC0_CFG1SET;
+ icr[2] = ic ? IC1_CFG2SET : IC0_CFG2SET;
+ icr[3] = ic ? IC1_CFG0CLR : IC0_CFG0CLR;
+ icr[4] = ic ? IC1_CFG1CLR : IC0_CFG1CLR;
+ icr[5] = ic ? IC1_CFG2CLR : IC0_CFG2CLR;
+
+ ret = 0;
+
+ switch (flow_type) { /* cfgregs 2:1:0 */
+ case IRQ_TYPE_EDGE_RISING: /* 0:0:1 */
+ au_writel(1 << bit, icr[5]);
+ au_writel(1 << bit, icr[4]);
+ au_writel(1 << bit, icr[0]);
+ set_irq_chip_and_handler_name(irq, chip,
+ handle_edge_irq, "riseedge");
+ break;
+ case IRQ_TYPE_EDGE_FALLING: /* 0:1:0 */
+ au_writel(1 << bit, icr[5]);
+ au_writel(1 << bit, icr[1]);
+ au_writel(1 << bit, icr[3]);
+ set_irq_chip_and_handler_name(irq, chip,
+ handle_edge_irq, "falledge");
+ break;
+ case IRQ_TYPE_EDGE_BOTH: /* 0:1:1 */
+ au_writel(1 << bit, icr[5]);
+ au_writel(1 << bit, icr[1]);
+ au_writel(1 << bit, icr[0]);
+ set_irq_chip_and_handler_name(irq, chip,
+ handle_edge_irq, "bothedge");
+ break;
+ case IRQ_TYPE_LEVEL_HIGH: /* 1:0:1 */
+ au_writel(1 << bit, icr[2]);
+ au_writel(1 << bit, icr[4]);
+ au_writel(1 << bit, icr[0]);
+ set_irq_chip_and_handler_name(irq, chip,
+ handle_level_irq, "hilevel");
+ break;
+ case IRQ_TYPE_LEVEL_LOW: /* 1:1:0 */
+ au_writel(1 << bit, icr[2]);
+ au_writel(1 << bit, icr[1]);
+ au_writel(1 << bit, icr[3]);
+ set_irq_chip_and_handler_name(irq, chip,
+ handle_level_irq, "lowlevel");
+ break;
+ case IRQ_TYPE_NONE: /* 0:0:0 */
+ au_writel(1 << bit, icr[5]);
+ au_writel(1 << bit, icr[4]);
+ au_writel(1 << bit, icr[3]);
+ /* set at least chip so we can call set_irq_type() on it */
+ set_irq_chip(irq, chip);
+ break;
+ default:
+ ret = -EINVAL;
+ }
+ au_sync();
+
+ return ret;
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+ unsigned int pending = read_c0_status() & read_c0_cause();
+ unsigned long s, off, bit;
+
+ if (pending & CAUSEF_IP7) {
+ do_IRQ(MIPS_CPU_IRQ_BASE + 7);
return;
+ } else if (pending & CAUSEF_IP2) {
+ s = IC0_REQ0INT;
+ off = AU1000_INTC0_INT_BASE;
+ } else if (pending & CAUSEF_IP3) {
+ s = IC0_REQ1INT;
+ off = AU1000_INTC0_INT_BASE;
+ } else if (pending & CAUSEF_IP4) {
+ s = IC1_REQ0INT;
+ off = AU1000_INTC1_INT_BASE;
+ } else if (pending & CAUSEF_IP5) {
+ s = IC1_REQ1INT;
+ off = AU1000_INTC1_INT_BASE;
+ } else
+ goto spurious;
+ bit = 0;
+ s = au_readl(s);
+ if (unlikely(!s)) {
+spurious:
+ spurious_interrupt();
+ return;
+ }
#ifdef AU1000_USB_DEV_REQ_INT
/*
* Because of the tight timing of SETUP token to reply
* transactions, the USB devices-side packet complete
* interrupt needs the highest priority.
*/
- if ((intc0_req0 & (1 << AU1000_USB_DEV_REQ_INT))) {
- intc0_req0 &= ~(1 << AU1000_USB_DEV_REQ_INT);
+ bit = 1 << (AU1000_USB_DEV_REQ_INT - AU1000_INTC0_INT_BASE);
+ if ((pending & CAUSEF_IP2) && (s & bit)) {
do_IRQ(AU1000_USB_DEV_REQ_INT);
return;
}
#endif
- bit = __ffs(intc0_req0);
- intc0_req0 &= ~(1 << bit);
- do_IRQ(AU1000_INTC0_INT_BASE + bit);
+ do_IRQ(__ffs(s) + off);
}
-
-static void intc0_req1_irqdispatch(void)
+/* setup edge/level and assign request 0/1 */
+void __init au1xxx_setup_irqmap(struct au1xxx_irqmap *map, int count)
{
- static unsigned long intc0_req1;
- unsigned int bit;
+ unsigned int bit, irq_nr;
- intc0_req1 |= au_readl(IC0_REQ1INT);
+ while (count--) {
+ irq_nr = map[count].im_irq;
- if (!intc0_req1)
- return;
+ if (((irq_nr < AU1000_INTC0_INT_BASE) ||
+ (irq_nr >= AU1000_INTC0_INT_BASE + 32)) &&
+ ((irq_nr < AU1000_INTC1_INT_BASE) ||
+ (irq_nr >= AU1000_INTC1_INT_BASE + 32)))
+ continue;
- bit = __ffs(intc0_req1);
- intc0_req1 &= ~(1 << bit);
- do_IRQ(AU1000_INTC0_INT_BASE + bit);
-}
+ if (irq_nr >= AU1000_INTC1_INT_BASE) {
+ bit = irq_nr - AU1000_INTC1_INT_BASE;
+ if (map[count].im_request)
+ au_writel(1 << bit, IC1_ASSIGNCLR);
+ } else {
+ bit = irq_nr - AU1000_INTC0_INT_BASE;
+ if (map[count].im_request)
+ au_writel(1 << bit, IC0_ASSIGNCLR);
+ }
-
-/*
- * Interrupt Controller 1:
- * interrupts 32 - 63
- */
-static void intc1_req0_irqdispatch(void)
-{
- static unsigned long intc1_req0;
- unsigned int bit;
-
- intc1_req0 |= au_readl(IC1_REQ0INT);
-
- if (!intc1_req0)
- return;
-
- bit = __ffs(intc1_req0);
- intc1_req0 &= ~(1 << bit);
- do_IRQ(AU1000_INTC1_INT_BASE + bit);
-}
-
-
-static void intc1_req1_irqdispatch(void)
-{
- static unsigned long intc1_req1;
- unsigned int bit;
-
- intc1_req1 |= au_readl(IC1_REQ1INT);
-
- if (!intc1_req1)
- return;
-
- bit = __ffs(intc1_req1);
- intc1_req1 &= ~(1 << bit);
- do_IRQ(AU1000_INTC1_INT_BASE + bit);
-}
-
-asmlinkage void plat_irq_dispatch(void)
-{
- unsigned int pending = read_c0_status() & read_c0_cause();
-
- if (pending & CAUSEF_IP7)
- do_IRQ(MIPS_CPU_IRQ_BASE + 7);
- else if (pending & CAUSEF_IP2)
- intc0_req0_irqdispatch();
- else if (pending & CAUSEF_IP3)
- intc0_req1_irqdispatch();
- else if (pending & CAUSEF_IP4)
- intc1_req0_irqdispatch();
- else if (pending & CAUSEF_IP5)
- intc1_req1_irqdispatch();
- else
- spurious_interrupt();
+ au1x_ic_settype(irq_nr, map[count].im_type);
+ }
}
void __init arch_init_irq(void)
{
int i;
- struct au1xxx_irqmap *imp;
- extern struct au1xxx_irqmap au1xxx_irq_map[];
- extern struct au1xxx_irqmap au1xxx_ic0_map[];
- extern int au1xxx_nr_irqs;
- extern int au1xxx_ic0_nr_irqs;
/*
* Initialize interrupt controllers to a safe state.
@@ -569,28 +589,67 @@
mips_cpu_irq_init();
+ /* register all 64 possible IC0+IC1 irq sources as type "none".
+ * Use set_irq_type() to set edge/level behaviour at runtime.
+ */
+ for (i = AU1000_INTC0_INT_BASE;
+ (i < AU1000_INTC0_INT_BASE + 32); i++)
+ au1x_ic_settype(i, IRQ_TYPE_NONE);
+
+ for (i = AU1000_INTC1_INT_BASE;
+ (i < AU1000_INTC1_INT_BASE + 32); i++)
+ au1x_ic_settype(i, IRQ_TYPE_NONE);
+
/*
* Initialize IC0, which is fixed per processor.
*/
- imp = au1xxx_ic0_map;
- for (i = 0; i < au1xxx_ic0_nr_irqs; i++) {
- setup_local_irq(imp->im_irq, imp->im_type, imp->im_request);
- imp++;
- }
+ au1xxx_setup_irqmap(au1xxx_ic0_map, ARRAY_SIZE(au1xxx_ic0_map));
- /*
- * Now set up the irq mapping for the board.
- */
- imp = au1xxx_irq_map;
- for (i = 0; i < au1xxx_nr_irqs; i++) {
- setup_local_irq(imp->im_irq, imp->im_type, imp->im_request);
- imp++;
- }
-
- set_c0_status(IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3 | IE_IRQ4);
-
- /* Board specific IRQ initialization.
+ /* Boards can register additional (GPIO-based) IRQs.
*/
- if (board_init_irq)
- board_init_irq();
+ board_init_irq();
+
+ set_c0_status(IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3);
+}
+
+unsigned long save_local_and_disable(int controller)
+{
+ int i;
+ unsigned long flags, mask;
+
+ spin_lock_irqsave(&irq_lock, flags);
+ if (controller) {
+ mask = au_readl(IC1_MASKSET);
+ for (i = 0; i < 32; i++)
+ au1x_ic1_mask(i + AU1000_INTC1_INT_BASE);
+ } else {
+ mask = au_readl(IC0_MASKSET);
+ for (i = 0; i < 32; i++)
+ au1x_ic0_mask(i + AU1000_INTC0_INT_BASE);
+ }
+ spin_unlock_irqrestore(&irq_lock, flags);
+
+ return mask;
+}
+
+void restore_local_and_enable(int controller, unsigned long mask)
+{
+ int i;
+ unsigned long flags, new_mask;
+
+ spin_lock_irqsave(&irq_lock, flags);
+ for (i = 0; i < 32; i++)
+ if (mask & (1 << i)) {
+ if (controller)
+ au1x_ic1_unmask(i + AU1000_INTC1_INT_BASE);
+ else
+ au1x_ic0_unmask(i + AU1000_INTC0_INT_BASE);
+ }
+
+ if (controller)
+ new_mask = au_readl(IC1_MASKSET);
+ else
+ new_mask = au_readl(IC0_MASKSET);
+
+ spin_unlock_irqrestore(&irq_lock, flags);
}