ARM: OMAP1: Use generic map_io, init_early and init_irq
This allows removing omap hacks for map_io allowing generic
map_io.
Note that in the future we can't do cpu_is_omapxxxx detection
until in init_early. This means that board-innovator.c now
assumes 15xx only, and board-generic.c assumes 16xx only.
This is best fixed later on by passing the SoC type from
device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index 312ea6b..4427737 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -135,12 +135,6 @@
*(volatile __u16 *) AMS_DELTA_LATCH2_VIRT = ams_delta_latch2_reg;
}
-static void __init ams_delta_init_irq(void)
-{
- omap1_init_common_hw();
- omap1_init_irq();
-}
-
static struct map_desc ams_delta_io_desc[] __initdata = {
/* AMS_DELTA_LATCH1 */
{
@@ -379,17 +373,13 @@
}
arch_initcall(ams_delta_modem_init);
-static void __init ams_delta_map_io(void)
-{
- omap1_map_common_io();
-}
-
MACHINE_START(AMS_DELTA, "Amstrad E3 (Delta)")
/* Maintainer: Jonathan McDowell <noodles@earth.li> */
.boot_params = 0x10000100,
- .map_io = ams_delta_map_io,
+ .map_io = omap15xx_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = ams_delta_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = ams_delta_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index a6b1bea..b09dfe6 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -297,63 +297,6 @@
static void __init omap_fsample_init(void)
{
- fsample_init_smc91x();
-
- if (gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0)
- BUG();
- gpio_direction_input(FSAMPLE_NAND_RB_GPIO_PIN);
-
- omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
- omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
-
- /* Mux pins for keypad */
- omap_cfg_reg(E2_7XX_KBR0);
- omap_cfg_reg(J7_7XX_KBR1);
- omap_cfg_reg(E1_7XX_KBR2);
- omap_cfg_reg(F3_7XX_KBR3);
- omap_cfg_reg(D2_7XX_KBR4);
- omap_cfg_reg(C2_7XX_KBC0);
- omap_cfg_reg(D3_7XX_KBC1);
- omap_cfg_reg(E4_7XX_KBC2);
- omap_cfg_reg(F4_7XX_KBC3);
- omap_cfg_reg(E3_7XX_KBC4);
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
- omap_board_config = fsample_config;
- omap_board_config_size = ARRAY_SIZE(fsample_config);
- omap_serial_init();
- omap_register_i2c_bus(1, 100, NULL, 0);
-}
-
-static void __init omap_fsample_init_irq(void)
-{
- omap1_init_common_hw();
- omap1_init_irq();
-}
-
-/* Only FPGA needs to be mapped here. All others are done with ioremap */
-static struct map_desc omap_fsample_io_desc[] __initdata = {
- {
- .virtual = H2P2_DBG_FPGA_BASE,
- .pfn = __phys_to_pfn(H2P2_DBG_FPGA_START),
- .length = H2P2_DBG_FPGA_SIZE,
- .type = MT_DEVICE
- },
- {
- .virtual = FSAMPLE_CPLD_BASE,
- .pfn = __phys_to_pfn(FSAMPLE_CPLD_START),
- .length = FSAMPLE_CPLD_SIZE,
- .type = MT_DEVICE
- }
-};
-
-static void __init omap_fsample_map_io(void)
-{
- omap1_map_common_io();
- iotable_init(omap_fsample_io_desc,
- ARRAY_SIZE(omap_fsample_io_desc));
-
/* Early, board-dependent init */
/*
@@ -384,15 +327,68 @@
* Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
* It is used as the Ethernet controller interrupt
*/
- omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF, OMAP7XX_IO_CONF_9);
+ omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF,
+ OMAP7XX_IO_CONF_9);
+
+ fsample_init_smc91x();
+
+ if (gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0)
+ BUG();
+ gpio_direction_input(FSAMPLE_NAND_RB_GPIO_PIN);
+
+ omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
+ omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
+
+ /* Mux pins for keypad */
+ omap_cfg_reg(E2_7XX_KBR0);
+ omap_cfg_reg(J7_7XX_KBR1);
+ omap_cfg_reg(E1_7XX_KBR2);
+ omap_cfg_reg(F3_7XX_KBR3);
+ omap_cfg_reg(D2_7XX_KBR4);
+ omap_cfg_reg(C2_7XX_KBC0);
+ omap_cfg_reg(D3_7XX_KBC1);
+ omap_cfg_reg(E4_7XX_KBC2);
+ omap_cfg_reg(F4_7XX_KBC3);
+ omap_cfg_reg(E3_7XX_KBC4);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
+
+ omap_board_config = fsample_config;
+ omap_board_config_size = ARRAY_SIZE(fsample_config);
+ omap_serial_init();
+ omap_register_i2c_bus(1, 100, NULL, 0);
+}
+
+/* Only FPGA needs to be mapped here. All others are done with ioremap */
+static struct map_desc omap_fsample_io_desc[] __initdata = {
+ {
+ .virtual = H2P2_DBG_FPGA_BASE,
+ .pfn = __phys_to_pfn(H2P2_DBG_FPGA_START),
+ .length = H2P2_DBG_FPGA_SIZE,
+ .type = MT_DEVICE
+ },
+ {
+ .virtual = FSAMPLE_CPLD_BASE,
+ .pfn = __phys_to_pfn(FSAMPLE_CPLD_START),
+ .length = FSAMPLE_CPLD_SIZE,
+ .type = MT_DEVICE
+ }
+};
+
+static void __init omap_fsample_map_io(void)
+{
+ omap15xx_map_io();
+ iotable_init(omap_fsample_io_desc,
+ ARRAY_SIZE(omap_fsample_io_desc));
}
MACHINE_START(OMAP_FSAMPLE, "OMAP730 F-Sample")
/* Maintainer: Brian Swetland <swetland@google.com> */
.boot_params = 0x10000100,
.map_io = omap_fsample_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = omap_fsample_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = omap_fsample_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/board-generic.c b/arch/arm/mach-omap1/board-generic.c
index 04fc356..cc0cca7 100644
--- a/arch/arm/mach-omap1/board-generic.c
+++ b/arch/arm/mach-omap1/board-generic.c
@@ -28,12 +28,6 @@
#include <plat/board.h>
#include <plat/common.h>
-static void __init omap_generic_init_irq(void)
-{
- omap1_init_common_hw();
- omap1_init_irq();
-}
-
/* assume no Mini-AB port */
#ifdef CONFIG_ARCH_OMAP15XX
@@ -87,17 +81,13 @@
omap_register_i2c_bus(1, 100, NULL, 0);
}
-static void __init omap_generic_map_io(void)
-{
- omap1_map_common_io();
-}
-
MACHINE_START(OMAP_GENERIC, "Generic OMAP1510/1610/1710")
/* Maintainer: Tony Lindgren <tony@atomide.com> */
.boot_params = 0x10000100,
- .map_io = omap_generic_map_io,
+ .map_io = omap16xx_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = omap_generic_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = omap_generic_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c
index cb7fb1a..248a5b8 100644
--- a/arch/arm/mach-omap1/board-h2.c
+++ b/arch/arm/mach-omap1/board-h2.c
@@ -373,12 +373,6 @@
},
};
-static void __init h2_init_irq(void)
-{
- omap1_init_common_hw();
- omap1_init_irq();
-}
-
static struct omap_usb_config h2_usb_config __initdata = {
/* usb1 has a Mini-AB port and external isp1301 transceiver */
.otg = 2,
@@ -454,17 +448,13 @@
h2_mmc_init();
}
-static void __init h2_map_io(void)
-{
- omap1_map_common_io();
-}
-
MACHINE_START(OMAP_H2, "TI-H2")
/* Maintainer: Imre Deak <imre.deak@nokia.com> */
.boot_params = 0x10000100,
- .map_io = h2_map_io,
+ .map_io = omap16xx_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = h2_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = h2_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c
index 31f3487..f28f05f 100644
--- a/arch/arm/mach-omap1/board-h3.c
+++ b/arch/arm/mach-omap1/board-h3.c
@@ -436,23 +436,13 @@
h3_mmc_init();
}
-static void __init h3_init_irq(void)
-{
- omap1_init_common_hw();
- omap1_init_irq();
-}
-
-static void __init h3_map_io(void)
-{
- omap1_map_common_io();
-}
-
MACHINE_START(OMAP_H3, "TI OMAP1710 H3 board")
/* Maintainer: Texas Instruments, Inc. */
.boot_params = 0x10000100,
- .map_io = h3_map_io,
+ .map_io = omap16xx_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = h3_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = h3_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/board-htcherald.c b/arch/arm/mach-omap1/board-htcherald.c
index 36e06ea..67798df 100644
--- a/arch/arm/mach-omap1/board-htcherald.c
+++ b/arch/arm/mach-omap1/board-htcherald.c
@@ -500,7 +500,7 @@
static void __init htcherald_map_io(void)
{
- omap1_map_common_io();
+ omap7xx_map_io();
/*
* The LCD panel must be disabled and DMA turned off here, as doing
@@ -601,20 +601,14 @@
#endif
}
-static void __init htcherald_init_irq(void)
-{
- printk(KERN_INFO "htcherald_init_irq.\n");
- omap1_init_common_hw();
- omap1_init_irq();
-}
-
MACHINE_START(HERALD, "HTC Herald")
/* Maintainer: Cory Maccarrone <darkstar6262@gmail.com> */
/* Maintainer: wing-linux.sourceforge.net */
.boot_params = 0x10000100,
.map_io = htcherald_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = htcherald_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = htcherald_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c
index 0b1ba46..3e349d0 100644
--- a/arch/arm/mach-omap1/board-innovator.c
+++ b/arch/arm/mach-omap1/board-innovator.c
@@ -289,12 +289,6 @@
}
}
-static void __init innovator_init_irq(void)
-{
- omap1_init_common_hw();
- omap1_init_irq();
-}
-
#ifdef CONFIG_ARCH_OMAP15XX
static struct omap_usb_config innovator1510_usb_config __initdata = {
/* for bundled non-standard host and peripheral cables */
@@ -439,30 +433,32 @@
innovator_mmc_init();
}
+/*
+ * REVISIT: Assume 15xx for now, we don't want to do revision check
+ * until later on. The right way to fix this is to set up a different
+ * machine_id for 16xx Innovator, or use device tree.
+ */
static void __init innovator_map_io(void)
{
- omap1_map_common_io();
+ omap15xx_map_io();
-#ifdef CONFIG_ARCH_OMAP15XX
- if (cpu_is_omap1510()) {
- iotable_init(innovator1510_io_desc, ARRAY_SIZE(innovator1510_io_desc));
- udelay(10); /* Delay needed for FPGA */
+ iotable_init(innovator1510_io_desc, ARRAY_SIZE(innovator1510_io_desc));
+ udelay(10); /* Delay needed for FPGA */
- /* Dump the Innovator FPGA rev early - useful info for support. */
- printk("Innovator FPGA Rev %d.%d Board Rev %d\n",
- fpga_read(OMAP1510_FPGA_REV_HIGH),
- fpga_read(OMAP1510_FPGA_REV_LOW),
- fpga_read(OMAP1510_FPGA_BOARD_REV));
- }
-#endif
+ /* Dump the Innovator FPGA rev early - useful info for support. */
+ pr_debug("Innovator FPGA Rev %d.%d Board Rev %d\n",
+ fpga_read(OMAP1510_FPGA_REV_HIGH),
+ fpga_read(OMAP1510_FPGA_REV_LOW),
+ fpga_read(OMAP1510_FPGA_BOARD_REV));
}
MACHINE_START(OMAP_INNOVATOR, "TI-Innovator")
/* Maintainer: MontaVista Software, Inc. */
.boot_params = 0x10000100,
.map_io = innovator_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = innovator_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = innovator_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/board-nokia770.c b/arch/arm/mach-omap1/board-nokia770.c
index 5469ce2..9b348b6 100644
--- a/arch/arm/mach-omap1/board-nokia770.c
+++ b/arch/arm/mach-omap1/board-nokia770.c
@@ -39,21 +39,6 @@
#define ADS7846_PENDOWN_GPIO 15
-static void __init omap_nokia770_init_irq(void)
-{
- /* On Nokia 770, the SleepX signal is masked with an
- * MPUIO line by default. It has to be unmasked for it
- * to become functional */
-
- /* SleepX mask direction */
- omap_writew((omap_readw(0xfffb5008) & ~2), 0xfffb5008);
- /* Unmask SleepX signal */
- omap_writew((omap_readw(0xfffb5004) & ~2), 0xfffb5004);
-
- omap1_init_common_hw();
- omap1_init_irq();
-}
-
static const unsigned int nokia770_keymap[] = {
KEY(1, 0, GROUP_0 | KEY_UP),
KEY(2, 0, GROUP_1 | KEY_F5),
@@ -246,6 +231,15 @@
static void __init omap_nokia770_init(void)
{
+ /* On Nokia 770, the SleepX signal is masked with an
+ * MPUIO line by default. It has to be unmasked for it
+ * to become functional */
+
+ /* SleepX mask direction */
+ omap_writew((omap_readw(0xfffb5008) & ~2), 0xfffb5008);
+ /* Unmask SleepX signal */
+ omap_writew((omap_readw(0xfffb5004) & ~2), 0xfffb5004);
+
platform_add_devices(nokia770_devices, ARRAY_SIZE(nokia770_devices));
spi_register_board_info(nokia770_spi_board_info,
ARRAY_SIZE(nokia770_spi_board_info));
@@ -258,16 +252,12 @@
nokia770_mmc_init();
}
-static void __init omap_nokia770_map_io(void)
-{
- omap1_map_common_io();
-}
-
MACHINE_START(NOKIA770, "Nokia 770")
.boot_params = 0x10000100,
- .map_io = omap_nokia770_map_io,
+ .map_io = omap16xx_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = omap_nokia770_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = omap_nokia770_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index b08a213..562986e 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -279,12 +279,6 @@
irq_set_irq_type(gpio_to_irq(62), IRQ_TYPE_EDGE_FALLING);
}
-static void __init osk_init_irq(void)
-{
- omap1_init_common_hw();
- omap1_init_irq();
-}
-
static struct omap_usb_config osk_usb_config __initdata = {
/* has usb host connector (A) ... for development it can also
* be used, with a NONSTANDARD gender-bending cable/dongle, as
@@ -576,17 +570,13 @@
osk_mistral_init();
}
-static void __init osk_map_io(void)
-{
- omap1_map_common_io();
-}
-
MACHINE_START(OMAP_OSK, "TI-OSK")
/* Maintainer: Dirk Behme <dirk.behme@de.bosch.com> */
.boot_params = 0x10000100,
- .map_io = osk_map_io,
+ .map_io = omap16xx_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = osk_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = osk_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/board-palmte.c b/arch/arm/mach-omap1/board-palmte.c
index 459cb6b..fc9edd8 100644
--- a/arch/arm/mach-omap1/board-palmte.c
+++ b/arch/arm/mach-omap1/board-palmte.c
@@ -59,12 +59,6 @@
#define PALMTE_MMC2_GPIO OMAP_MPUIO(7)
#define PALMTE_MMC3_GPIO OMAP_MPUIO(11)
-static void __init omap_palmte_init_irq(void)
-{
- omap1_init_common_hw();
- omap1_init_irq();
-}
-
static const unsigned int palmte_keymap[] = {
KEY(0, 0, KEY_F1), /* Calendar */
KEY(1, 0, KEY_F2), /* Contacts */
@@ -269,16 +263,12 @@
omap_register_i2c_bus(1, 100, NULL, 0);
}
-static void __init omap_palmte_map_io(void)
-{
- omap1_map_common_io();
-}
-
MACHINE_START(OMAP_PALMTE, "OMAP310 based Palm Tungsten E")
.boot_params = 0x10000100,
- .map_io = omap_palmte_map_io,
+ .map_io = omap15xx_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = omap_palmte_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = omap_palmte_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/board-palmtt.c b/arch/arm/mach-omap1/board-palmtt.c
index b214f45..5ff3def 100644
--- a/arch/arm/mach-omap1/board-palmtt.c
+++ b/arch/arm/mach-omap1/board-palmtt.c
@@ -263,12 +263,6 @@
}
};
-static void __init omap_palmtt_init_irq(void)
-{
- omap1_init_common_hw();
- omap1_init_irq();
-}
-
static struct omap_usb_config palmtt_usb_config __initdata = {
.register_dev = 1,
.hmc_mode = 0,
@@ -315,16 +309,12 @@
omap_register_i2c_bus(1, 100, NULL, 0);
}
-static void __init omap_palmtt_map_io(void)
-{
- omap1_map_common_io();
-}
-
MACHINE_START(OMAP_PALMTT, "OMAP1510 based Palm Tungsten|T")
.boot_params = 0x10000100,
- .map_io = omap_palmtt_map_io,
+ .map_io = omap15xx_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = omap_palmtt_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = omap_palmtt_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/board-palmz71.c b/arch/arm/mach-omap1/board-palmz71.c
index 9b0ea48..8e08873 100644
--- a/arch/arm/mach-omap1/board-palmz71.c
+++ b/arch/arm/mach-omap1/board-palmz71.c
@@ -57,13 +57,6 @@
#define PALMZ71_SLIDER_GPIO OMAP_MPUIO(3)
#define PALMZ71_MMC_IN_GPIO OMAP_MPUIO(4)
-static void __init
-omap_palmz71_init_irq(void)
-{
- omap1_init_common_hw();
- omap1_init_irq();
-}
-
static const unsigned int palmz71_keymap[] = {
KEY(0, 0, KEY_F1),
KEY(1, 0, KEY_F2),
@@ -334,17 +327,12 @@
palmz71_gpio_setup(0);
}
-static void __init
-omap_palmz71_map_io(void)
-{
- omap1_map_common_io();
-}
-
MACHINE_START(OMAP_PALMZ71, "OMAP310 based Palm Zire71")
.boot_params = 0x10000100,
- .map_io = omap_palmz71_map_io,
+ .map_io = omap15xx_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = omap_palmz71_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = omap_palmz71_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c
index 67acd41..6ed649b 100644
--- a/arch/arm/mach-omap1/board-perseus2.c
+++ b/arch/arm/mach-omap1/board-perseus2.c
@@ -265,56 +265,6 @@
static void __init omap_perseus2_init(void)
{
- perseus2_init_smc91x();
-
- if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
- BUG();
- gpio_direction_input(P2_NAND_RB_GPIO_PIN);
-
- omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
- omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
-
- /* Mux pins for keypad */
- omap_cfg_reg(E2_7XX_KBR0);
- omap_cfg_reg(J7_7XX_KBR1);
- omap_cfg_reg(E1_7XX_KBR2);
- omap_cfg_reg(F3_7XX_KBR3);
- omap_cfg_reg(D2_7XX_KBR4);
- omap_cfg_reg(C2_7XX_KBC0);
- omap_cfg_reg(D3_7XX_KBC1);
- omap_cfg_reg(E4_7XX_KBC2);
- omap_cfg_reg(F4_7XX_KBC3);
- omap_cfg_reg(E3_7XX_KBC4);
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
- omap_board_config = perseus2_config;
- omap_board_config_size = ARRAY_SIZE(perseus2_config);
- omap_serial_init();
- omap_register_i2c_bus(1, 100, NULL, 0);
-}
-
-static void __init omap_perseus2_init_irq(void)
-{
- omap1_init_common_hw();
- omap1_init_irq();
-}
-/* Only FPGA needs to be mapped here. All others are done with ioremap */
-static struct map_desc omap_perseus2_io_desc[] __initdata = {
- {
- .virtual = H2P2_DBG_FPGA_BASE,
- .pfn = __phys_to_pfn(H2P2_DBG_FPGA_START),
- .length = H2P2_DBG_FPGA_SIZE,
- .type = MT_DEVICE
- }
-};
-
-static void __init omap_perseus2_map_io(void)
-{
- omap1_map_common_io();
- iotable_init(omap_perseus2_io_desc,
- ARRAY_SIZE(omap_perseus2_io_desc));
-
/* Early, board-dependent init */
/*
@@ -345,15 +295,62 @@
* Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
* It is used as the Ethernet controller interrupt
*/
- omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF, OMAP7XX_IO_CONF_9);
+ omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF,
+ OMAP7XX_IO_CONF_9);
+
+ perseus2_init_smc91x();
+
+ if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
+ BUG();
+ gpio_direction_input(P2_NAND_RB_GPIO_PIN);
+
+ omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
+ omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
+
+ /* Mux pins for keypad */
+ omap_cfg_reg(E2_7XX_KBR0);
+ omap_cfg_reg(J7_7XX_KBR1);
+ omap_cfg_reg(E1_7XX_KBR2);
+ omap_cfg_reg(F3_7XX_KBR3);
+ omap_cfg_reg(D2_7XX_KBR4);
+ omap_cfg_reg(C2_7XX_KBC0);
+ omap_cfg_reg(D3_7XX_KBC1);
+ omap_cfg_reg(E4_7XX_KBC2);
+ omap_cfg_reg(F4_7XX_KBC3);
+ omap_cfg_reg(E3_7XX_KBC4);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
+
+ omap_board_config = perseus2_config;
+ omap_board_config_size = ARRAY_SIZE(perseus2_config);
+ omap_serial_init();
+ omap_register_i2c_bus(1, 100, NULL, 0);
+}
+
+/* Only FPGA needs to be mapped here. All others are done with ioremap */
+static struct map_desc omap_perseus2_io_desc[] __initdata = {
+ {
+ .virtual = H2P2_DBG_FPGA_BASE,
+ .pfn = __phys_to_pfn(H2P2_DBG_FPGA_START),
+ .length = H2P2_DBG_FPGA_SIZE,
+ .type = MT_DEVICE
+ }
+};
+
+static void __init omap_perseus2_map_io(void)
+{
+ omap7xx_map_io();
+ iotable_init(omap_perseus2_io_desc,
+ ARRAY_SIZE(omap_perseus2_io_desc));
}
MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2")
/* Maintainer: Kevin Hilman <kjh@hilman.org> */
.boot_params = 0x10000100,
.map_io = omap_perseus2_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = omap_perseus2_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = omap_perseus2_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/board-sx1.c b/arch/arm/mach-omap1/board-sx1.c
index 9c3b7c5..23326e0 100644
--- a/arch/arm/mach-omap1/board-sx1.c
+++ b/arch/arm/mach-omap1/board-sx1.c
@@ -407,24 +407,13 @@
gpio_direction_output(11, 0); /*A_SWITCH = 0 */
gpio_direction_output(15, 0); /*A_USB_ON = 0 */
}
-/*----------------------------------------*/
-static void __init omap_sx1_init_irq(void)
-{
- omap1_init_common_hw();
- omap1_init_irq();
-}
-/*----------------------------------------*/
-
-static void __init omap_sx1_map_io(void)
-{
- omap1_map_common_io();
-}
MACHINE_START(SX1, "OMAP310 based Siemens SX1")
.boot_params = 0x10000100,
- .map_io = omap_sx1_map_io,
+ .map_io = omap15xx_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = omap_sx1_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = omap_sx1_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/board-voiceblue.c b/arch/arm/mach-omap1/board-voiceblue.c
index 036edc0e..1444ce8 100644
--- a/arch/arm/mach-omap1/board-voiceblue.c
+++ b/arch/arm/mach-omap1/board-voiceblue.c
@@ -159,17 +159,6 @@
static struct omap_board_config_kernel voiceblue_config[] = {
};
-static void __init voiceblue_init_irq(void)
-{
- omap1_init_common_hw();
- omap1_init_irq();
-}
-
-static void __init voiceblue_map_io(void)
-{
- omap1_map_common_io();
-}
-
#define MACHINE_PANICED 1
#define MACHINE_REBOOTING 2
#define MACHINE_REBOOT 4
@@ -302,9 +291,10 @@
MACHINE_START(VOICEBLUE, "VoiceBlue OMAP5910")
/* Maintainer: Ladislav Michl <michl@2n.cz> */
.boot_params = 0x10000100,
- .map_io = voiceblue_map_io,
+ .map_io = omap15xx_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = voiceblue_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = voiceblue_init,
.timer = &omap1_timer,
MACHINE_END
diff --git a/arch/arm/mach-omap1/io.c b/arch/arm/mach-omap1/io.c
index 870886a..a16aab7 100644
--- a/arch/arm/mach-omap1/io.c
+++ b/arch/arm/mach-omap1/io.c
@@ -85,50 +85,44 @@
#endif
/*
- * Maps common IO regions for omap1. This should only get called from
- * board specific init.
+ * Maps common IO regions for omap1
*/
-void __init omap1_map_common_io(void)
+static void __init omap1_map_common_io(void)
{
iotable_init(omap_io_desc, ARRAY_SIZE(omap_io_desc));
-
- /* Normally devicemaps_init() would flush caches and tlb after
- * mdesc->map_io(), but we must also do it here because of the CPU
- * revision check below.
- */
- local_flush_tlb_all();
- flush_cache_all();
-
- /* We want to check CPU revision early for cpu_is_omapxxxx() macros.
- * IO space mapping must be initialized before we can do that.
- */
- omap_check_revision();
-
-#if defined (CONFIG_ARCH_OMAP730) || defined (CONFIG_ARCH_OMAP850)
- if (cpu_is_omap7xx()) {
- iotable_init(omap7xx_io_desc, ARRAY_SIZE(omap7xx_io_desc));
- }
-#endif
-#ifdef CONFIG_ARCH_OMAP15XX
- if (cpu_is_omap15xx()) {
- iotable_init(omap1510_io_desc, ARRAY_SIZE(omap1510_io_desc));
- }
-#endif
-#if defined(CONFIG_ARCH_OMAP16XX)
- if (cpu_is_omap16xx()) {
- iotable_init(omap16xx_io_desc, ARRAY_SIZE(omap16xx_io_desc));
- }
-#endif
-
- omap_sram_init();
}
-/*
- * Common low-level hardware init for omap1. This should only get called from
- * board specific init.
- */
-void __init omap1_init_common_hw(void)
+#if defined (CONFIG_ARCH_OMAP730) || defined (CONFIG_ARCH_OMAP850)
+void __init omap7xx_map_io(void)
{
+ omap1_map_common_io();
+ iotable_init(omap7xx_io_desc, ARRAY_SIZE(omap7xx_io_desc));
+}
+#endif
+
+#ifdef CONFIG_ARCH_OMAP15XX
+void __init omap15xx_map_io(void)
+{
+ omap1_map_common_io();
+ iotable_init(omap1510_io_desc, ARRAY_SIZE(omap1510_io_desc));
+}
+#endif
+
+#if defined(CONFIG_ARCH_OMAP16XX)
+void __init omap16xx_map_io(void)
+{
+ omap1_map_common_io();
+ iotable_init(omap16xx_io_desc, ARRAY_SIZE(omap16xx_io_desc));
+}
+#endif
+
+/*
+ * Common low-level hardware init for omap1.
+ */
+void omap1_init_early(void)
+{
+ omap_check_revision();
+
/* REVISIT: Refer to OMAP5910 Errata, Advisory SYS_1: "Timeout Abort
* on a Posted Write in the TIPB Bridge".
*/
@@ -138,8 +132,8 @@
/* Must init clocks early to assure that timer interrupt works
*/
omap1_clk_init();
-
omap1_mux_init();
+ omap_sram_init();
}
/*
diff --git a/arch/arm/plat-omap/include/plat/io.h b/arch/arm/plat-omap/include/plat/io.h
index 6591875..c0c7850 100644
--- a/arch/arm/plat-omap/include/plat/io.h
+++ b/arch/arm/plat-omap/include/plat/io.h
@@ -256,8 +256,31 @@
struct omap_sdrc_params;
-extern void omap1_map_common_io(void);
-extern void omap1_init_common_hw(void);
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+void omap7xx_map_io(void);
+#else
+static inline void omap_map_io(void)
+{
+}
+#endif
+
+#ifdef CONFIG_ARCH_OMAP15XX
+void omap15xx_map_io(void);
+#else
+static inline void omap15xx_map_io(void)
+{
+}
+#endif
+
+#ifdef CONFIG_ARCH_OMAP16XX
+void omap16xx_map_io(void);
+#else
+static inline void omap16xx_map_io(void)
+{
+}
+#endif
+
+void omap1_init_early(void);
#ifdef CONFIG_SOC_OMAP2420
extern void omap242x_map_common_io(void);