[SCSI] qla2xxx: Add support to retrieve/update HBA option-rom.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
diff --git a/drivers/scsi/qla2xxx/qla_sup.c b/drivers/scsi/qla2xxx/qla_sup.c
index 3105bb9..3866a57 100644
--- a/drivers/scsi/qla2xxx/qla_sup.c
+++ b/drivers/scsi/qla2xxx/qla_sup.c
@@ -989,3 +989,672 @@
return QLA_SUCCESS;
}
+
+
+/*
+ * Flash support routines
+ */
+
+/**
+ * qla2x00_flash_enable() - Setup flash for reading and writing.
+ * @ha: HA context
+ */
+static void
+qla2x00_flash_enable(scsi_qla_host_t *ha)
+{
+ uint16_t data;
+ struct device_reg_2xxx __iomem *reg = &ha->iobase->isp;
+
+ data = RD_REG_WORD(®->ctrl_status);
+ data |= CSR_FLASH_ENABLE;
+ WRT_REG_WORD(®->ctrl_status, data);
+ RD_REG_WORD(®->ctrl_status); /* PCI Posting. */
+}
+
+/**
+ * qla2x00_flash_disable() - Disable flash and allow RISC to run.
+ * @ha: HA context
+ */
+static void
+qla2x00_flash_disable(scsi_qla_host_t *ha)
+{
+ uint16_t data;
+ struct device_reg_2xxx __iomem *reg = &ha->iobase->isp;
+
+ data = RD_REG_WORD(®->ctrl_status);
+ data &= ~(CSR_FLASH_ENABLE);
+ WRT_REG_WORD(®->ctrl_status, data);
+ RD_REG_WORD(®->ctrl_status); /* PCI Posting. */
+}
+
+/**
+ * qla2x00_read_flash_byte() - Reads a byte from flash
+ * @ha: HA context
+ * @addr: Address in flash to read
+ *
+ * A word is read from the chip, but, only the lower byte is valid.
+ *
+ * Returns the byte read from flash @addr.
+ */
+static uint8_t
+qla2x00_read_flash_byte(scsi_qla_host_t *ha, uint32_t addr)
+{
+ uint16_t data;
+ uint16_t bank_select;
+ struct device_reg_2xxx __iomem *reg = &ha->iobase->isp;
+
+ bank_select = RD_REG_WORD(®->ctrl_status);
+
+ if (IS_QLA2322(ha) || IS_QLA6322(ha)) {
+ /* Specify 64K address range: */
+ /* clear out Module Select and Flash Address bits [19:16]. */
+ bank_select &= ~0xf8;
+ bank_select |= addr >> 12 & 0xf0;
+ bank_select |= CSR_FLASH_64K_BANK;
+ WRT_REG_WORD(®->ctrl_status, bank_select);
+ RD_REG_WORD(®->ctrl_status); /* PCI Posting. */
+
+ WRT_REG_WORD(®->flash_address, (uint16_t)addr);
+ data = RD_REG_WORD(®->flash_data);
+
+ return (uint8_t)data;
+ }
+
+ /* Setup bit 16 of flash address. */
+ if ((addr & BIT_16) && ((bank_select & CSR_FLASH_64K_BANK) == 0)) {
+ bank_select |= CSR_FLASH_64K_BANK;
+ WRT_REG_WORD(®->ctrl_status, bank_select);
+ RD_REG_WORD(®->ctrl_status); /* PCI Posting. */
+ } else if (((addr & BIT_16) == 0) &&
+ (bank_select & CSR_FLASH_64K_BANK)) {
+ bank_select &= ~(CSR_FLASH_64K_BANK);
+ WRT_REG_WORD(®->ctrl_status, bank_select);
+ RD_REG_WORD(®->ctrl_status); /* PCI Posting. */
+ }
+
+ /* Always perform IO mapped accesses to the FLASH registers. */
+ if (ha->pio_address) {
+ uint16_t data2;
+
+ reg = (struct device_reg_2xxx __iomem *)ha->pio_address;
+ WRT_REG_WORD_PIO(®->flash_address, (uint16_t)addr);
+ do {
+ data = RD_REG_WORD_PIO(®->flash_data);
+ barrier();
+ cpu_relax();
+ data2 = RD_REG_WORD_PIO(®->flash_data);
+ } while (data != data2);
+ } else {
+ WRT_REG_WORD(®->flash_address, (uint16_t)addr);
+ data = qla2x00_debounce_register(®->flash_data);
+ }
+
+ return (uint8_t)data;
+}
+
+/**
+ * qla2x00_write_flash_byte() - Write a byte to flash
+ * @ha: HA context
+ * @addr: Address in flash to write
+ * @data: Data to write
+ */
+static void
+qla2x00_write_flash_byte(scsi_qla_host_t *ha, uint32_t addr, uint8_t data)
+{
+ uint16_t bank_select;
+ struct device_reg_2xxx __iomem *reg = &ha->iobase->isp;
+
+ bank_select = RD_REG_WORD(®->ctrl_status);
+ if (IS_QLA2322(ha) || IS_QLA6322(ha)) {
+ /* Specify 64K address range: */
+ /* clear out Module Select and Flash Address bits [19:16]. */
+ bank_select &= ~0xf8;
+ bank_select |= addr >> 12 & 0xf0;
+ bank_select |= CSR_FLASH_64K_BANK;
+ WRT_REG_WORD(®->ctrl_status, bank_select);
+ RD_REG_WORD(®->ctrl_status); /* PCI Posting. */
+
+ WRT_REG_WORD(®->flash_address, (uint16_t)addr);
+ RD_REG_WORD(®->ctrl_status); /* PCI Posting. */
+ WRT_REG_WORD(®->flash_data, (uint16_t)data);
+ RD_REG_WORD(®->ctrl_status); /* PCI Posting. */
+
+ return;
+ }
+
+ /* Setup bit 16 of flash address. */
+ if ((addr & BIT_16) && ((bank_select & CSR_FLASH_64K_BANK) == 0)) {
+ bank_select |= CSR_FLASH_64K_BANK;
+ WRT_REG_WORD(®->ctrl_status, bank_select);
+ RD_REG_WORD(®->ctrl_status); /* PCI Posting. */
+ } else if (((addr & BIT_16) == 0) &&
+ (bank_select & CSR_FLASH_64K_BANK)) {
+ bank_select &= ~(CSR_FLASH_64K_BANK);
+ WRT_REG_WORD(®->ctrl_status, bank_select);
+ RD_REG_WORD(®->ctrl_status); /* PCI Posting. */
+ }
+
+ /* Always perform IO mapped accesses to the FLASH registers. */
+ if (ha->pio_address) {
+ reg = (struct device_reg_2xxx __iomem *)ha->pio_address;
+ WRT_REG_WORD_PIO(®->flash_address, (uint16_t)addr);
+ WRT_REG_WORD_PIO(®->flash_data, (uint16_t)data);
+ } else {
+ WRT_REG_WORD(®->flash_address, (uint16_t)addr);
+ RD_REG_WORD(®->ctrl_status); /* PCI Posting. */
+ WRT_REG_WORD(®->flash_data, (uint16_t)data);
+ RD_REG_WORD(®->ctrl_status); /* PCI Posting. */
+ }
+}
+
+/**
+ * qla2x00_poll_flash() - Polls flash for completion.
+ * @ha: HA context
+ * @addr: Address in flash to poll
+ * @poll_data: Data to be polled
+ * @man_id: Flash manufacturer ID
+ * @flash_id: Flash ID
+ *
+ * This function polls the device until bit 7 of what is read matches data
+ * bit 7 or until data bit 5 becomes a 1. If that hapens, the flash ROM timed
+ * out (a fatal error). The flash book recommeds reading bit 7 again after
+ * reading bit 5 as a 1.
+ *
+ * Returns 0 on success, else non-zero.
+ */
+static int
+qla2x00_poll_flash(scsi_qla_host_t *ha, uint32_t addr, uint8_t poll_data,
+ uint8_t man_id, uint8_t flash_id)
+{
+ int status;
+ uint8_t flash_data;
+ uint32_t cnt;
+
+ status = 1;
+
+ /* Wait for 30 seconds for command to finish. */
+ poll_data &= BIT_7;
+ for (cnt = 3000000; cnt; cnt--) {
+ flash_data = qla2x00_read_flash_byte(ha, addr);
+ if ((flash_data & BIT_7) == poll_data) {
+ status = 0;
+ break;
+ }
+
+ if (man_id != 0x40 && man_id != 0xda) {
+ if ((flash_data & BIT_5) && cnt > 2)
+ cnt = 2;
+ }
+ udelay(10);
+ barrier();
+ }
+ return status;
+}
+
+#define IS_OEM_001(ha) \
+ ((ha)->pdev->device == PCI_DEVICE_ID_QLOGIC_ISP2322 && \
+ (ha)->pdev->subsystem_vendor == 0x1028 && \
+ (ha)->pdev->subsystem_device == 0x0170)
+
+/**
+ * qla2x00_program_flash_address() - Programs a flash address
+ * @ha: HA context
+ * @addr: Address in flash to program
+ * @data: Data to be written in flash
+ * @man_id: Flash manufacturer ID
+ * @flash_id: Flash ID
+ *
+ * Returns 0 on success, else non-zero.
+ */
+static int
+qla2x00_program_flash_address(scsi_qla_host_t *ha, uint32_t addr, uint8_t data,
+ uint8_t man_id, uint8_t flash_id)
+{
+ /* Write Program Command Sequence. */
+ if (IS_OEM_001(ha)) {
+ qla2x00_write_flash_byte(ha, 0xaaa, 0xaa);
+ qla2x00_write_flash_byte(ha, 0x555, 0x55);
+ qla2x00_write_flash_byte(ha, 0xaaa, 0xa0);
+ qla2x00_write_flash_byte(ha, addr, data);
+ } else {
+ if (man_id == 0xda && flash_id == 0xc1) {
+ qla2x00_write_flash_byte(ha, addr, data);
+ if (addr & 0x7e)
+ return 0;
+ } else {
+ qla2x00_write_flash_byte(ha, 0x5555, 0xaa);
+ qla2x00_write_flash_byte(ha, 0x2aaa, 0x55);
+ qla2x00_write_flash_byte(ha, 0x5555, 0xa0);
+ qla2x00_write_flash_byte(ha, addr, data);
+ }
+ }
+
+ udelay(150);
+
+ /* Wait for write to complete. */
+ return qla2x00_poll_flash(ha, addr, data, man_id, flash_id);
+}
+
+/**
+ * qla2x00_erase_flash() - Erase the flash.
+ * @ha: HA context
+ * @man_id: Flash manufacturer ID
+ * @flash_id: Flash ID
+ *
+ * Returns 0 on success, else non-zero.
+ */
+static int
+qla2x00_erase_flash(scsi_qla_host_t *ha, uint8_t man_id, uint8_t flash_id)
+{
+ /* Individual Sector Erase Command Sequence */
+ if (IS_OEM_001(ha)) {
+ qla2x00_write_flash_byte(ha, 0xaaa, 0xaa);
+ qla2x00_write_flash_byte(ha, 0x555, 0x55);
+ qla2x00_write_flash_byte(ha, 0xaaa, 0x80);
+ qla2x00_write_flash_byte(ha, 0xaaa, 0xaa);
+ qla2x00_write_flash_byte(ha, 0x555, 0x55);
+ qla2x00_write_flash_byte(ha, 0xaaa, 0x10);
+ } else {
+ qla2x00_write_flash_byte(ha, 0x5555, 0xaa);
+ qla2x00_write_flash_byte(ha, 0x2aaa, 0x55);
+ qla2x00_write_flash_byte(ha, 0x5555, 0x80);
+ qla2x00_write_flash_byte(ha, 0x5555, 0xaa);
+ qla2x00_write_flash_byte(ha, 0x2aaa, 0x55);
+ qla2x00_write_flash_byte(ha, 0x5555, 0x10);
+ }
+
+ udelay(150);
+
+ /* Wait for erase to complete. */
+ return qla2x00_poll_flash(ha, 0x00, 0x80, man_id, flash_id);
+}
+
+/**
+ * qla2x00_erase_flash_sector() - Erase a flash sector.
+ * @ha: HA context
+ * @addr: Flash sector to erase
+ * @sec_mask: Sector address mask
+ * @man_id: Flash manufacturer ID
+ * @flash_id: Flash ID
+ *
+ * Returns 0 on success, else non-zero.
+ */
+static int
+qla2x00_erase_flash_sector(scsi_qla_host_t *ha, uint32_t addr,
+ uint32_t sec_mask, uint8_t man_id, uint8_t flash_id)
+{
+ /* Individual Sector Erase Command Sequence */
+ qla2x00_write_flash_byte(ha, 0x5555, 0xaa);
+ qla2x00_write_flash_byte(ha, 0x2aaa, 0x55);
+ qla2x00_write_flash_byte(ha, 0x5555, 0x80);
+ qla2x00_write_flash_byte(ha, 0x5555, 0xaa);
+ qla2x00_write_flash_byte(ha, 0x2aaa, 0x55);
+ if (man_id == 0x1f && flash_id == 0x13)
+ qla2x00_write_flash_byte(ha, addr & sec_mask, 0x10);
+ else
+ qla2x00_write_flash_byte(ha, addr & sec_mask, 0x30);
+
+ udelay(150);
+
+ /* Wait for erase to complete. */
+ return qla2x00_poll_flash(ha, addr, 0x80, man_id, flash_id);
+}
+
+/**
+ * qla2x00_get_flash_manufacturer() - Read manufacturer ID from flash chip.
+ * @man_id: Flash manufacturer ID
+ * @flash_id: Flash ID
+ */
+static void
+qla2x00_get_flash_manufacturer(scsi_qla_host_t *ha, uint8_t *man_id,
+ uint8_t *flash_id)
+{
+ qla2x00_write_flash_byte(ha, 0x5555, 0xaa);
+ qla2x00_write_flash_byte(ha, 0x2aaa, 0x55);
+ qla2x00_write_flash_byte(ha, 0x5555, 0x90);
+ *man_id = qla2x00_read_flash_byte(ha, 0x0000);
+ *flash_id = qla2x00_read_flash_byte(ha, 0x0001);
+ qla2x00_write_flash_byte(ha, 0x5555, 0xaa);
+ qla2x00_write_flash_byte(ha, 0x2aaa, 0x55);
+ qla2x00_write_flash_byte(ha, 0x5555, 0xf0);
+}
+
+
+static inline void
+qla2x00_suspend_hba(struct scsi_qla_host *ha)
+{
+ int cnt;
+ unsigned long flags;
+ struct device_reg_2xxx __iomem *reg = &ha->iobase->isp;
+
+ /* Suspend HBA. */
+ scsi_block_requests(ha->host);
+ ha->isp_ops.disable_intrs(ha);
+ set_bit(MBX_UPDATE_FLASH_ACTIVE, &ha->mbx_cmd_flags);
+
+ /* Pause RISC. */
+ spin_lock_irqsave(&ha->hardware_lock, flags);
+ WRT_REG_WORD(®->hccr, HCCR_PAUSE_RISC);
+ RD_REG_WORD(®->hccr);
+ if (IS_QLA2100(ha) || IS_QLA2200(ha) || IS_QLA2300(ha)) {
+ for (cnt = 0; cnt < 30000; cnt++) {
+ if ((RD_REG_WORD(®->hccr) & HCCR_RISC_PAUSE) != 0)
+ break;
+ udelay(100);
+ }
+ } else {
+ udelay(10);
+ }
+ spin_unlock_irqrestore(&ha->hardware_lock, flags);
+}
+
+static inline void
+qla2x00_resume_hba(struct scsi_qla_host *ha)
+{
+ /* Resume HBA. */
+ clear_bit(MBX_UPDATE_FLASH_ACTIVE, &ha->mbx_cmd_flags);
+ set_bit(ISP_ABORT_NEEDED, &ha->dpc_flags);
+ up(ha->dpc_wait);
+ qla2x00_wait_for_hba_online(ha);
+ scsi_unblock_requests(ha->host);
+}
+
+uint8_t *
+qla2x00_read_optrom_data(struct scsi_qla_host *ha, uint8_t *buf,
+ uint32_t offset, uint32_t length)
+{
+ unsigned long flags;
+ uint32_t addr, midpoint;
+ uint8_t *data;
+ struct device_reg_2xxx __iomem *reg = &ha->iobase->isp;
+
+ /* Suspend HBA. */
+ qla2x00_suspend_hba(ha);
+
+ /* Go with read. */
+ spin_lock_irqsave(&ha->hardware_lock, flags);
+ midpoint = ha->optrom_size / 2;
+
+ qla2x00_flash_enable(ha);
+ WRT_REG_WORD(®->nvram, 0);
+ RD_REG_WORD(®->nvram); /* PCI Posting. */
+ for (addr = offset, data = buf; addr < length; addr++, data++) {
+ if (addr == midpoint) {
+ WRT_REG_WORD(®->nvram, NVR_SELECT);
+ RD_REG_WORD(®->nvram); /* PCI Posting. */
+ }
+
+ *data = qla2x00_read_flash_byte(ha, addr);
+ }
+ qla2x00_flash_disable(ha);
+ spin_unlock_irqrestore(&ha->hardware_lock, flags);
+
+ /* Resume HBA. */
+ qla2x00_resume_hba(ha);
+
+ return buf;
+}
+
+int
+qla2x00_write_optrom_data(struct scsi_qla_host *ha, uint8_t *buf,
+ uint32_t offset, uint32_t length)
+{
+
+ int rval;
+ unsigned long flags;
+ uint8_t man_id, flash_id, sec_number, data;
+ uint16_t wd;
+ uint32_t addr, liter, sec_mask, rest_addr;
+ struct device_reg_2xxx __iomem *reg = &ha->iobase->isp;
+
+ /* Suspend HBA. */
+ qla2x00_suspend_hba(ha);
+
+ rval = QLA_SUCCESS;
+ sec_number = 0;
+
+ /* Reset ISP chip. */
+ spin_lock_irqsave(&ha->hardware_lock, flags);
+ WRT_REG_WORD(®->ctrl_status, CSR_ISP_SOFT_RESET);
+ pci_read_config_word(ha->pdev, PCI_COMMAND, &wd);
+
+ /* Go with write. */
+ qla2x00_flash_enable(ha);
+ do { /* Loop once to provide quick error exit */
+ /* Structure of flash memory based on manufacturer */
+ if (IS_OEM_001(ha)) {
+ /* OEM variant with special flash part. */
+ man_id = flash_id = 0;
+ rest_addr = 0xffff;
+ sec_mask = 0x10000;
+ goto update_flash;
+ }
+ qla2x00_get_flash_manufacturer(ha, &man_id, &flash_id);
+ switch (man_id) {
+ case 0x20: /* ST flash. */
+ if (flash_id == 0xd2 || flash_id == 0xe3) {
+ /*
+ * ST m29w008at part - 64kb sector size with
+ * 32kb,8kb,8kb,16kb sectors at memory address
+ * 0xf0000.
+ */
+ rest_addr = 0xffff;
+ sec_mask = 0x10000;
+ break;
+ }
+ /*
+ * ST m29w010b part - 16kb sector size
+ * Default to 16kb sectors
+ */
+ rest_addr = 0x3fff;
+ sec_mask = 0x1c000;
+ break;
+ case 0x40: /* Mostel flash. */
+ /* Mostel v29c51001 part - 512 byte sector size. */
+ rest_addr = 0x1ff;
+ sec_mask = 0x1fe00;
+ break;
+ case 0xbf: /* SST flash. */
+ /* SST39sf10 part - 4kb sector size. */
+ rest_addr = 0xfff;
+ sec_mask = 0x1f000;
+ break;
+ case 0xda: /* Winbond flash. */
+ /* Winbond W29EE011 part - 256 byte sector size. */
+ rest_addr = 0x7f;
+ sec_mask = 0x1ff80;
+ break;
+ case 0xc2: /* Macronix flash. */
+ /* 64k sector size. */
+ if (flash_id == 0x38 || flash_id == 0x4f) {
+ rest_addr = 0xffff;
+ sec_mask = 0x10000;
+ break;
+ }
+ /* Fall through... */
+
+ case 0x1f: /* Atmel flash. */
+ /* 512k sector size. */
+ if (flash_id == 0x13) {
+ rest_addr = 0x7fffffff;
+ sec_mask = 0x80000000;
+ break;
+ }
+ /* Fall through... */
+
+ case 0x01: /* AMD flash. */
+ if (flash_id == 0x38 || flash_id == 0x40 ||
+ flash_id == 0x4f) {
+ /* Am29LV081 part - 64kb sector size. */
+ /* Am29LV002BT part - 64kb sector size. */
+ rest_addr = 0xffff;
+ sec_mask = 0x10000;
+ break;
+ } else if (flash_id == 0x3e) {
+ /*
+ * Am29LV008b part - 64kb sector size with
+ * 32kb,8kb,8kb,16kb sector at memory address
+ * h0xf0000.
+ */
+ rest_addr = 0xffff;
+ sec_mask = 0x10000;
+ break;
+ } else if (flash_id == 0x20 || flash_id == 0x6e) {
+ /*
+ * Am29LV010 part or AM29f010 - 16kb sector
+ * size.
+ */
+ rest_addr = 0x3fff;
+ sec_mask = 0x1c000;
+ break;
+ } else if (flash_id == 0x6d) {
+ /* Am29LV001 part - 8kb sector size. */
+ rest_addr = 0x1fff;
+ sec_mask = 0x1e000;
+ break;
+ }
+ default:
+ /* Default to 16 kb sector size. */
+ rest_addr = 0x3fff;
+ sec_mask = 0x1c000;
+ break;
+ }
+
+update_flash:
+ if (IS_QLA2322(ha) || IS_QLA6322(ha)) {
+ if (qla2x00_erase_flash(ha, man_id, flash_id)) {
+ rval = QLA_FUNCTION_FAILED;
+ break;
+ }
+ }
+
+ for (addr = offset, liter = 0; liter < length; liter++,
+ addr++) {
+ data = buf[liter];
+ /* Are we at the beginning of a sector? */
+ if ((addr & rest_addr) == 0) {
+ if (IS_QLA2322(ha) || IS_QLA6322(ha)) {
+ if (addr >= 0x10000UL) {
+ if (((addr >> 12) & 0xf0) &&
+ ((man_id == 0x01 &&
+ flash_id == 0x3e) ||
+ (man_id == 0x20 &&
+ flash_id == 0xd2))) {
+ sec_number++;
+ if (sec_number == 1) {
+ rest_addr =
+ 0x7fff;
+ sec_mask =
+ 0x18000;
+ } else if (
+ sec_number == 2 ||
+ sec_number == 3) {
+ rest_addr =
+ 0x1fff;
+ sec_mask =
+ 0x1e000;
+ } else if (
+ sec_number == 4) {
+ rest_addr =
+ 0x3fff;
+ sec_mask =
+ 0x1c000;
+ }
+ }
+ }
+ } else if (addr == ha->optrom_size / 2) {
+ WRT_REG_WORD(®->nvram, NVR_SELECT);
+ RD_REG_WORD(®->nvram);
+ }
+
+ if (flash_id == 0xda && man_id == 0xc1) {
+ qla2x00_write_flash_byte(ha, 0x5555,
+ 0xaa);
+ qla2x00_write_flash_byte(ha, 0x2aaa,
+ 0x55);
+ qla2x00_write_flash_byte(ha, 0x5555,
+ 0xa0);
+ } else if (!IS_QLA2322(ha) && !IS_QLA6322(ha)) {
+ /* Then erase it */
+ if (qla2x00_erase_flash_sector(ha,
+ addr, sec_mask, man_id,
+ flash_id)) {
+ rval = QLA_FUNCTION_FAILED;
+ break;
+ }
+ if (man_id == 0x01 && flash_id == 0x6d)
+ sec_number++;
+ }
+ }
+
+ if (man_id == 0x01 && flash_id == 0x6d) {
+ if (sec_number == 1 &&
+ addr == (rest_addr - 1)) {
+ rest_addr = 0x0fff;
+ sec_mask = 0x1f000;
+ } else if (sec_number == 3 && (addr & 0x7ffe)) {
+ rest_addr = 0x3fff;
+ sec_mask = 0x1c000;
+ }
+ }
+
+ if (qla2x00_program_flash_address(ha, addr, data,
+ man_id, flash_id)) {
+ rval = QLA_FUNCTION_FAILED;
+ break;
+ }
+ }
+ } while (0);
+ qla2x00_flash_disable(ha);
+ spin_unlock_irqrestore(&ha->hardware_lock, flags);
+
+ /* Resume HBA. */
+ qla2x00_resume_hba(ha);
+
+ return rval;
+}
+
+uint8_t *
+qla24xx_read_optrom_data(struct scsi_qla_host *ha, uint8_t *buf,
+ uint32_t offset, uint32_t length)
+{
+ /* Suspend HBA. */
+ scsi_block_requests(ha->host);
+ ha->isp_ops.disable_intrs(ha);
+ set_bit(MBX_UPDATE_FLASH_ACTIVE, &ha->mbx_cmd_flags);
+
+ /* Go with read. */
+ qla24xx_read_flash_data(ha, (uint32_t *)buf, offset >> 2, length >> 2);
+
+ /* Resume HBA. */
+ clear_bit(MBX_UPDATE_FLASH_ACTIVE, &ha->mbx_cmd_flags);
+ ha->isp_ops.enable_intrs(ha);
+ scsi_unblock_requests(ha->host);
+
+ return buf;
+}
+
+int
+qla24xx_write_optrom_data(struct scsi_qla_host *ha, uint8_t *buf,
+ uint32_t offset, uint32_t length)
+{
+ int rval;
+
+ /* Suspend HBA. */
+ scsi_block_requests(ha->host);
+ ha->isp_ops.disable_intrs(ha);
+ set_bit(MBX_UPDATE_FLASH_ACTIVE, &ha->mbx_cmd_flags);
+
+ /* Go with write. */
+ rval = qla24xx_write_flash_data(ha, (uint32_t *)buf, offset >> 2,
+ length >> 2);
+
+ /* Resume HBA -- RISC reset needed. */
+ clear_bit(MBX_UPDATE_FLASH_ACTIVE, &ha->mbx_cmd_flags);
+ set_bit(ISP_ABORT_NEEDED, &ha->dpc_flags);
+ up(ha->dpc_wait);
+ qla2x00_wait_for_hba_online(ha);
+ scsi_unblock_requests(ha->host);
+
+ return rval;
+}