/*
 *   pata-legacy.c - Legacy port PATA/SATA controller driver.
 *   Copyright 2005/2006 Red Hat <alan@redhat.com>, all rights reserved.
 *
 *  This program is free software; you can redistribute it and/or modify
 *  it under the terms of the GNU General Public License as published by
 *  the Free Software Foundation; either version 2, or (at your option)
 *  any later version.
 *
 *  This program is distributed in the hope that it will be useful,
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *  GNU General Public License for more details.
 *
 *  You should have received a copy of the GNU General Public License
 *  along with this program; see the file COPYING.  If not, write to
 *  the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
 *
 *   An ATA driver for the legacy ATA ports.
 *
 *   Data Sources:
 *	Opti 82C465/82C611 support: Data sheets at opti-inc.com
 *	HT6560 series:
 *	Promise 20230/20620:
 *		http://www.ryston.cz/petr/vlb/pdc20230b.html
 *		http://www.ryston.cz/petr/vlb/pdc20230c.html
 *		http://www.ryston.cz/petr/vlb/pdc20630.html
 *
 *  Unsupported but docs exist:
 *	Appian/Adaptec AIC25VL01/Cirrus Logic PD7220
 *	Winbond W83759A
 *
 *  This driver handles legacy (that is "ISA/VLB side") IDE ports found
 *  on PC class systems. There are three hybrid devices that are exceptions
 *  The Cyrix 5510/5520 where a pre SFF ATA device is on the bridge and
 *  the MPIIX where the tuning is PCI side but the IDE is "ISA side".
 *
 *  Specific support is included for the ht6560a/ht6560b/opti82c611a/
 *  opti82c465mv/promise 20230c/20630
 *
 *  Use the autospeed and pio_mask options with:
 *	Appian ADI/2 aka CLPD7220 or AIC25VL01.
 *  Use the jumpers, autospeed and set pio_mask to the mode on the jumpers with
 *	Goldstar GM82C711, PIC-1288A-125, UMC 82C871F, Winbond W83759,
 *	Winbond W83759A, Promise PDC20230-B
 *
 *  For now use autospeed and pio_mask as above with the W83759A. This may
 *  change.
 *
 *  TODO
 *	Merge existing pata_qdi driver
 *
 */

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/ata.h>
#include <linux/libata.h>
#include <linux/platform_device.h>

#define DRV_NAME "pata_legacy"
#define DRV_VERSION "0.5.3"

#define NR_HOST 6

static int legacy_port[NR_HOST] = { 0x1f0, 0x170, 0x1e8, 0x168, 0x1e0, 0x160 };
static int legacy_irq[NR_HOST] = { 15, 14, 11, 10, 8, 12 };

struct legacy_data {
	unsigned long timing;
	u8 clock[2];
	u8 last;
	int fast;
	struct platform_device *platform_dev;

};

static struct legacy_data legacy_data[NR_HOST];
static struct ata_host *legacy_host[NR_HOST];
static int nr_legacy_host;


static int probe_all;			/* Set to check all ISA port ranges */
static int ht6560a;			/* HT 6560A on primary 1, secondary 2, both 3 */
static int ht6560b;			/* HT 6560A on primary 1, secondary 2, both 3 */
static int opti82c611a;			/* Opti82c611A on primary 1, secondary 2, both 3 */
static int opti82c46x;		/* Opti 82c465MV present (pri/sec autodetect) */
static int autospeed;			/* Chip present which snoops speed changes */
static int pio_mask = 0x1F;		/* PIO range for autospeed devices */

/**
 *	legacy_set_mode		-	mode setting
 *	@ap: IDE interface
 *
 *	Use a non standard set_mode function. We don't want to be tuned.
 *
 *	The BIOS configured everything. Our job is not to fiddle. Just use
 *	whatever PIO the hardware is using and leave it at that. When we
 *	get some kind of nice user driven API for control then we can
 *	expand on this as per hdparm in the base kernel.
 */

static void legacy_set_mode(struct ata_port *ap)
{
	int i;

	for (i = 0; i < ATA_MAX_DEVICES; i++) {
		struct ata_device *dev = &ap->device[i];
		if (ata_dev_enabled(dev)) {
			dev->pio_mode = XFER_PIO_0;
			dev->xfer_mode = XFER_PIO_0;
			dev->xfer_shift = ATA_SHIFT_PIO;
			dev->flags |= ATA_DFLAG_PIO;
		}
	}
}

static struct scsi_host_template legacy_sht = {
	.module			= THIS_MODULE,
	.name			= DRV_NAME,
	.ioctl			= ata_scsi_ioctl,
	.queuecommand		= ata_scsi_queuecmd,
	.can_queue		= ATA_DEF_QUEUE,
	.this_id		= ATA_SHT_THIS_ID,
	.sg_tablesize		= LIBATA_MAX_PRD,
	.max_sectors		= ATA_MAX_SECTORS,
	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
	.emulated		= ATA_SHT_EMULATED,
	.use_clustering		= ATA_SHT_USE_CLUSTERING,
	.proc_name		= DRV_NAME,
	.dma_boundary		= ATA_DMA_BOUNDARY,
	.slave_configure	= ata_scsi_slave_config,
	.bios_param		= ata_std_bios_param,
};

/*
 *	These ops are used if the user indicates the hardware
 *	snoops the commands to decide on the mode and handles the
 *	mode selection "magically" itself. Several legacy controllers
 *	do this. The mode range can be set if it is not 0x1F by setting
 *	pio_mask as well.
 */

static struct ata_port_operations simple_port_ops = {
	.port_disable	= ata_port_disable,
	.tf_load	= ata_tf_load,
	.tf_read	= ata_tf_read,
	.check_status 	= ata_check_status,
	.exec_command	= ata_exec_command,
	.dev_select 	= ata_std_dev_select,

	.freeze		= ata_bmdma_freeze,
	.thaw		= ata_bmdma_thaw,
	.error_handler	= ata_bmdma_error_handler,
	.post_internal_cmd = ata_bmdma_post_internal_cmd,

	.qc_prep 	= ata_qc_prep,
	.qc_issue	= ata_qc_issue_prot,
	.eng_timeout	= ata_eng_timeout,
	.data_xfer	= ata_pio_data_xfer_noirq,

	.irq_handler	= ata_interrupt,
	.irq_clear	= ata_bmdma_irq_clear,

	.port_start	= ata_port_start,
	.port_stop	= ata_port_stop,
	.host_stop	= ata_host_stop
};

static struct ata_port_operations legacy_port_ops = {
	.set_mode	= legacy_set_mode,

	.port_disable	= ata_port_disable,
	.tf_load	= ata_tf_load,
	.tf_read	= ata_tf_read,
	.check_status 	= ata_check_status,
	.exec_command	= ata_exec_command,
	.dev_select 	= ata_std_dev_select,

	.error_handler	= ata_bmdma_error_handler,

	.qc_prep 	= ata_qc_prep,
	.qc_issue	= ata_qc_issue_prot,
	.eng_timeout	= ata_eng_timeout,
	.data_xfer	= ata_pio_data_xfer_noirq,

	.irq_handler	= ata_interrupt,
	.irq_clear	= ata_bmdma_irq_clear,

	.port_start	= ata_port_start,
	.port_stop	= ata_port_stop,
	.host_stop	= ata_host_stop
};

/*
 *	Promise 20230C and 20620 support
 *
 *	This controller supports PIO0 to PIO2. We set PIO timings conservatively to
 *	allow for 50MHz Vesa Local Bus. The 20620 DMA support is weird being DMA to
 *	controller and PIO'd to the host and not supported.
 */

static void pdc20230_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
	int tries = 5;
	int pio = adev->pio_mode - XFER_PIO_0;
	u8 rt;
	unsigned long flags;

	/* Safe as UP only. Force I/Os to occur together */

	local_irq_save(flags);

	/* Unlock the control interface */
	do
	{
		inb(0x1F5);
		outb(inb(0x1F2) | 0x80, 0x1F2);
		inb(0x1F2);
		inb(0x3F6);
		inb(0x3F6);
		inb(0x1F2);
		inb(0x1F2);
	}
	while((inb(0x1F2) & 0x80) && --tries);

	local_irq_restore(flags);

	outb(inb(0x1F4) & 0x07, 0x1F4);

	rt = inb(0x1F3);
	rt &= 0x07 << (3 * adev->devno);
	if (pio)
		rt |= (1 + 3 * pio) << (3 * adev->devno);

	udelay(100);
	outb(inb(0x1F2) | 0x01, 0x1F2);
	udelay(100);
	inb(0x1F5);

}

static void pdc_data_xfer_vlb(struct ata_device *adev, unsigned char *buf, unsigned int buflen, int write_data)
{
	struct ata_port *ap = adev->ap;
	int slop = buflen & 3;
	unsigned long flags;

	if (ata_id_has_dword_io(adev->id)) {
		local_irq_save(flags);

		/* Perform the 32bit I/O synchronization sequence */
		inb(ap->ioaddr.nsect_addr);
		inb(ap->ioaddr.nsect_addr);
		inb(ap->ioaddr.nsect_addr);

		/* Now the data */

		if (write_data)
			outsl(ap->ioaddr.data_addr, buf, buflen >> 2);
		else
			insl(ap->ioaddr.data_addr, buf, buflen >> 2);

		if (unlikely(slop)) {
			u32 pad;
			if (write_data) {
				memcpy(&pad, buf + buflen - slop, slop);
				outl(le32_to_cpu(pad), ap->ioaddr.data_addr);
			} else {
				pad = cpu_to_le16(inl(ap->ioaddr.data_addr));
				memcpy(buf + buflen - slop, &pad, slop);
			}
		}
		local_irq_restore(flags);
	}
	else
		ata_pio_data_xfer_noirq(adev, buf, buflen, write_data);
}

static struct ata_port_operations pdc20230_port_ops = {
	.set_piomode	= pdc20230_set_piomode,

	.port_disable	= ata_port_disable,
	.tf_load	= ata_tf_load,
	.tf_read	= ata_tf_read,
	.check_status 	= ata_check_status,
	.exec_command	= ata_exec_command,
	.dev_select 	= ata_std_dev_select,

	.error_handler	= ata_bmdma_error_handler,

	.qc_prep 	= ata_qc_prep,
	.qc_issue	= ata_qc_issue_prot,
	.eng_timeout	= ata_eng_timeout,
	.data_xfer	= pdc_data_xfer_vlb,

	.irq_handler	= ata_interrupt,
	.irq_clear	= ata_bmdma_irq_clear,

	.port_start	= ata_port_start,
	.port_stop	= ata_port_stop,
	.host_stop	= ata_host_stop
};

/*
 *	Holtek 6560A support
 *
 *	This controller supports PIO0 to PIO2 (no IORDY even though higher timings
 *	can be loaded).
 */

static void ht6560a_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
	u8 active, recover;
	struct ata_timing t;

	/* Get the timing data in cycles. For now play safe at 50Mhz */
	ata_timing_compute(adev, adev->pio_mode, &t, 20000, 1000);

	active = FIT(t.active, 2, 15);
	recover = FIT(t.recover, 4, 15);

	inb(0x3E6);
	inb(0x3E6);
	inb(0x3E6);
	inb(0x3E6);

	outb(recover << 4 | active, ap->ioaddr.device_addr);
	inb(ap->ioaddr.status_addr);
}

static struct ata_port_operations ht6560a_port_ops = {
	.set_piomode	= ht6560a_set_piomode,

	.port_disable	= ata_port_disable,
	.tf_load	= ata_tf_load,
	.tf_read	= ata_tf_read,
	.check_status 	= ata_check_status,
	.exec_command	= ata_exec_command,
	.dev_select 	= ata_std_dev_select,

	.error_handler	= ata_bmdma_error_handler,

	.qc_prep 	= ata_qc_prep,
	.qc_issue	= ata_qc_issue_prot,
	.eng_timeout	= ata_eng_timeout,
	.data_xfer	= ata_pio_data_xfer,	/* Check vlb/noirq */

	.irq_handler	= ata_interrupt,
	.irq_clear	= ata_bmdma_irq_clear,

	.port_start	= ata_port_start,
	.port_stop	= ata_port_stop,
	.host_stop	= ata_host_stop
};

/*
 *	Holtek 6560B support
 *
 *	This controller supports PIO0 to PIO4. We honour the BIOS/jumper FIFO setting
 *	unless we see an ATAPI device in which case we force it off.
 *
 *	FIXME: need to implement 2nd channel support.
 */

static void ht6560b_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
	u8 active, recover;
	struct ata_timing t;

	/* Get the timing data in cycles. For now play safe at 50Mhz */
	ata_timing_compute(adev, adev->pio_mode, &t, 20000, 1000);

	active = FIT(t.active, 2, 15);
	recover = FIT(t.recover, 2, 16);
	recover &= 0x15;

	inb(0x3E6);
	inb(0x3E6);
	inb(0x3E6);
	inb(0x3E6);

	outb(recover << 4 | active, ap->ioaddr.device_addr);

	if (adev->class != ATA_DEV_ATA) {
		u8 rconf = inb(0x3E6);
		if (rconf & 0x24) {
			rconf &= ~ 0x24;
			outb(rconf, 0x3E6);
		}
	}
	inb(ap->ioaddr.status_addr);
}

static struct ata_port_operations ht6560b_port_ops = {
	.set_piomode	= ht6560b_set_piomode,

	.port_disable	= ata_port_disable,
	.tf_load	= ata_tf_load,
	.tf_read	= ata_tf_read,
	.check_status 	= ata_check_status,
	.exec_command	= ata_exec_command,
	.dev_select 	= ata_std_dev_select,

	.error_handler	= ata_bmdma_error_handler,

	.qc_prep 	= ata_qc_prep,
	.qc_issue	= ata_qc_issue_prot,
	.eng_timeout	= ata_eng_timeout,
	.data_xfer	= ata_pio_data_xfer,	/* FIXME: Check 32bit and noirq */

	.irq_handler	= ata_interrupt,
	.irq_clear	= ata_bmdma_irq_clear,

	.port_start	= ata_port_start,
	.port_stop	= ata_port_stop,
	.host_stop	= ata_host_stop
};

/*
 *	Opti core chipset helpers
 */

/**
 *	opti_syscfg	-	read OPTI chipset configuration
 *	@reg: Configuration register to read
 *
 *	Returns the value of an OPTI system board configuration register.
 */

static u8 opti_syscfg(u8 reg)
{
	unsigned long flags;
	u8 r;

	/* Uniprocessor chipset and must force cycles adjancent */
	local_irq_save(flags);
	outb(reg, 0x22);
	r = inb(0x24);
	local_irq_restore(flags);
	return r;
}

/*
 *	Opti 82C611A
 *
 *	This controller supports PIO0 to PIO3.
 */

static void opti82c611a_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
	u8 active, recover, setup;
	struct ata_timing t;
	struct ata_device *pair = ata_dev_pair(adev);
	int clock;
	int khz[4] = { 50000, 40000, 33000, 25000 };
	u8 rc;

	/* Enter configuration mode */
	inw(ap->ioaddr.error_addr);
	inw(ap->ioaddr.error_addr);
	outb(3, ap->ioaddr.nsect_addr);

	/* Read VLB clock strapping */
	clock = 1000000000 / khz[inb(ap->ioaddr.lbah_addr) & 0x03];

	/* Get the timing data in cycles */
	ata_timing_compute(adev, adev->pio_mode, &t, clock, 1000);

	/* Setup timing is shared */
	if (pair) {
		struct ata_timing tp;
		ata_timing_compute(pair, pair->pio_mode, &tp, clock, 1000);

		ata_timing_merge(&t, &tp, &t, ATA_TIMING_SETUP);
	}

	active = FIT(t.active, 2, 17) - 2;
	recover = FIT(t.recover, 1, 16) - 1;
	setup = FIT(t.setup, 1, 4) - 1;

	/* Select the right timing bank for write timing */
	rc = inb(ap->ioaddr.lbal_addr);
	rc &= 0x7F;
	rc |= (adev->devno << 7);
	outb(rc, ap->ioaddr.lbal_addr);

	/* Write the timings */
	outb(active << 4 | recover, ap->ioaddr.error_addr);

	/* Select the right bank for read timings, also
	   load the shared timings for address */
	rc = inb(ap->ioaddr.device_addr);
	rc &= 0xC0;
	rc |= adev->devno;	/* Index select */
	rc |= (setup << 4) | 0x04;
	outb(rc, ap->ioaddr.device_addr);

	/* Load the read timings */
	outb(active << 4 | recover, ap->ioaddr.data_addr);

	/* Ensure the timing register mode is right */
	rc = inb (ap->ioaddr.lbal_addr);
	rc &= 0x73;
	rc |= 0x84;
	outb(rc, ap->ioaddr.lbal_addr);

	/* Exit command mode */
	outb(0x83,  ap->ioaddr.nsect_addr);
}


static struct ata_port_operations opti82c611a_port_ops = {
	.set_piomode	= opti82c611a_set_piomode,

	.port_disable	= ata_port_disable,
	.tf_load	= ata_tf_load,
	.tf_read	= ata_tf_read,
	.check_status 	= ata_check_status,
	.exec_command	= ata_exec_command,
	.dev_select 	= ata_std_dev_select,

	.error_handler	= ata_bmdma_error_handler,

	.qc_prep 	= ata_qc_prep,
	.qc_issue	= ata_qc_issue_prot,
	.eng_timeout	= ata_eng_timeout,
	.data_xfer	= ata_pio_data_xfer,

	.irq_handler	= ata_interrupt,
	.irq_clear	= ata_bmdma_irq_clear,

	.port_start	= ata_port_start,
	.port_stop	= ata_port_stop,
	.host_stop	= ata_host_stop
};

/*
 *	Opti 82C465MV
 *
 *	This controller supports PIO0 to PIO3. Unlike the 611A the MVB
 *	version is dual channel but doesn't have a lot of unique registers.
 */

static void opti82c46x_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
	u8 active, recover, setup;
	struct ata_timing t;
	struct ata_device *pair = ata_dev_pair(adev);
	int clock;
	int khz[4] = { 50000, 40000, 33000, 25000 };
	u8 rc;
	u8 sysclk;

	/* Get the clock */
	sysclk = opti_syscfg(0xAC) & 0xC0;	/* BIOS set */

	/* Enter configuration mode */
	inw(ap->ioaddr.error_addr);
	inw(ap->ioaddr.error_addr);
	outb(3, ap->ioaddr.nsect_addr);

	/* Read VLB clock strapping */
	clock = 1000000000 / khz[sysclk];

	/* Get the timing data in cycles */
	ata_timing_compute(adev, adev->pio_mode, &t, clock, 1000);

	/* Setup timing is shared */
	if (pair) {
		struct ata_timing tp;
		ata_timing_compute(pair, pair->pio_mode, &tp, clock, 1000);

		ata_timing_merge(&t, &tp, &t, ATA_TIMING_SETUP);
	}

	active = FIT(t.active, 2, 17) - 2;
	recover = FIT(t.recover, 1, 16) - 1;
	setup = FIT(t.setup, 1, 4) - 1;

	/* Select the right timing bank for write timing */
	rc = inb(ap->ioaddr.lbal_addr);
	rc &= 0x7F;
	rc |= (adev->devno << 7);
	outb(rc, ap->ioaddr.lbal_addr);

	/* Write the timings */
	outb(active << 4 | recover, ap->ioaddr.error_addr);

	/* Select the right bank for read timings, also
	   load the shared timings for address */
	rc = inb(ap->ioaddr.device_addr);
	rc &= 0xC0;
	rc |= adev->devno;	/* Index select */
	rc |= (setup << 4) | 0x04;
	outb(rc, ap->ioaddr.device_addr);

	/* Load the read timings */
	outb(active << 4 | recover, ap->ioaddr.data_addr);

	/* Ensure the timing register mode is right */
	rc = inb (ap->ioaddr.lbal_addr);
	rc &= 0x73;
	rc |= 0x84;
	outb(rc, ap->ioaddr.lbal_addr);

	/* Exit command mode */
	outb(0x83,  ap->ioaddr.nsect_addr);

	/* We need to know this for quad device on the MVB */
	ap->host->private_data = ap;
}

/**
 *	opt82c465mv_qc_issue_prot	-	command issue
 *	@qc: command pending
 *
 *	Called when the libata layer is about to issue a command. We wrap
 *	this interface so that we can load the correct ATA timings. The
 *	MVB has a single set of timing registers and these are shared
 *	across channels. As there are two registers we really ought to
 *	track the last two used values as a sort of register window. For
 *	now we just reload on a channel switch. On the single channel
 *	setup this condition never fires so we do nothing extra.
 *
 *	FIXME: dual channel needs ->serialize support
 */

static unsigned int opti82c46x_qc_issue_prot(struct ata_queued_cmd *qc)
{
	struct ata_port *ap = qc->ap;
	struct ata_device *adev = qc->dev;

	/* If timings are set and for the wrong channel (2nd test is
	   due to a libata shortcoming and will eventually go I hope) */
	if (ap->host->private_data != ap->host
	    && ap->host->private_data != NULL)
		opti82c46x_set_piomode(ap, adev);

	return ata_qc_issue_prot(qc);
}

static struct ata_port_operations opti82c46x_port_ops = {
	.set_piomode	= opti82c46x_set_piomode,

	.port_disable	= ata_port_disable,
	.tf_load	= ata_tf_load,
	.tf_read	= ata_tf_read,
	.check_status 	= ata_check_status,
	.exec_command	= ata_exec_command,
	.dev_select 	= ata_std_dev_select,

	.error_handler	= ata_bmdma_error_handler,

	.qc_prep 	= ata_qc_prep,
	.qc_issue	= opti82c46x_qc_issue_prot,
	.eng_timeout	= ata_eng_timeout,
	.data_xfer	= ata_pio_data_xfer,

	.irq_handler	= ata_interrupt,
	.irq_clear	= ata_bmdma_irq_clear,

	.port_start	= ata_port_start,
	.port_stop	= ata_port_stop,
	.host_stop	= ata_host_stop
};


/**
 *	legacy_init_one		-	attach a legacy interface
 *	@port: port number
 *	@io: I/O port start
 *	@ctrl: control port
 *	@irq: interrupt line
 *
 *	Register an ISA bus IDE interface. Such interfaces are PIO and we
 *	assume do not support IRQ sharing.
 */

static __init int legacy_init_one(int port, unsigned long io, unsigned long ctrl, int irq)
{
	struct legacy_data *ld = &legacy_data[nr_legacy_host];
	struct ata_probe_ent ae;
	struct platform_device *pdev;
	int ret = -EBUSY;
	struct ata_port_operations *ops = &legacy_port_ops;
	int pio_modes = pio_mask;
	u32 mask = (1 << port);

	if (request_region(io, 8, "pata_legacy") == NULL)
		return -EBUSY;
	if (request_region(ctrl, 1, "pata_legacy") == NULL)
		goto fail_io;

	pdev = platform_device_register_simple(DRV_NAME, nr_legacy_host, NULL, 0);
	if (pdev == NULL)
		goto fail_dev;

	if (ht6560a & mask) {
		ops = &ht6560a_port_ops;
		pio_modes = 0x07;
	}
	if (ht6560b & mask) {
		ops = &ht6560b_port_ops;
		pio_modes = 0x1F;
	}
	if (opti82c611a & mask) {
		ops = &opti82c611a_port_ops;
		pio_modes = 0x0F;
	}
	if (opti82c46x & mask) {
		ops = &opti82c46x_port_ops;
		pio_modes = 0x0F;
	}

	/* Probe for automatically detectable controllers */

	if (io == 0x1F0 && ops == &legacy_port_ops) {
		unsigned long flags;

		local_irq_save(flags);

		/* Probes */
		inb(0x1F5);
		outb(inb(0x1F2) | 0x80, 0x1F2);
		inb(0x1F2);
		inb(0x3F6);
		inb(0x3F6);
		inb(0x1F2);
		inb(0x1F2);

		if ((inb(0x1F2) & 0x80) == 0) {
			/* PDC20230c or 20630 ? */
			printk(KERN_INFO "PDC20230-C/20630 VLB ATA controller detected.\n");
				pio_modes = 0x07;
			ops = &pdc20230_port_ops;
			udelay(100);
			inb(0x1F5);
		} else {
			outb(0x55, 0x1F2);
			inb(0x1F2);
			inb(0x1F2);
			if (inb(0x1F2) == 0x00) {
				printk(KERN_INFO "PDC20230-B VLB ATA controller detected.\n");
			}
		}
		local_irq_restore(flags);
	}


	/* Chip does mode setting by command snooping */
	if (ops == &legacy_port_ops && (autospeed & mask))
		ops = &simple_port_ops;
	memset(&ae, 0, sizeof(struct ata_probe_ent));
	INIT_LIST_HEAD(&ae.node);
	ae.dev = &pdev->dev;
	ae.port_ops = ops;
	ae.sht = &legacy_sht;
	ae.n_ports = 1;
	ae.pio_mask = pio_modes;
	ae.irq = irq;
	ae.irq_flags = 0;
	ae.port_flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST;
	ae.port[0].cmd_addr = io;
	ae.port[0].altstatus_addr = ctrl;
	ae.port[0].ctl_addr =	ctrl;
	ata_std_ports(&ae.port[0]);
	ae.private_data = ld;

	ret = ata_device_add(&ae);
	if (ret == 0) {
		ret = -ENODEV;
		goto fail;
	}
	legacy_host[nr_legacy_host++] = dev_get_drvdata(&pdev->dev);
	ld->platform_dev = pdev;
	return 0;

fail:
	platform_device_unregister(pdev);
fail_dev:
	release_region(ctrl, 1);
fail_io:
	release_region(io, 8);
	return ret;
}

/**
 *	legacy_check_special_cases	-	ATA special cases
 *	@p: PCI device to check
 *	@master: set this if we find an ATA master
 *	@master: set this if we find an ATA secondary
 *
 *	A small number of vendors implemented early PCI ATA interfaces on bridge logic
 *	without the ATA interface being PCI visible. Where we have a matching PCI driver
 *	we must skip the relevant device here. If we don't know about it then the legacy
 *	driver is the right driver anyway.
 */

static void legacy_check_special_cases(struct pci_dev *p, int *primary, int *secondary)
{
	/* Cyrix CS5510 pre SFF MWDMA ATA on the bridge */
	if (p->vendor == 0x1078 && p->device == 0x0000) {
		*primary = *secondary = 1;
		return;
	}
	/* Cyrix CS5520 pre SFF MWDMA ATA on the bridge */
	if (p->vendor == 0x1078 && p->device == 0x0002) {
		*primary = *secondary = 1;
		return;
	}
	/* Intel MPIIX - PIO ATA on non PCI side of bridge */
	if (p->vendor == 0x8086 && p->device == 0x1234) {
		u16 r;
		pci_read_config_word(p, 0x6C, &r);
		if (r & 0x8000) {	/* ATA port enabled */
			if (r & 0x4000)
				*secondary = 1;
			else
				*primary = 1;
		}
		return;
	}
}


/**
 *	legacy_init		-	attach legacy interfaces
 *
 *	Attach legacy IDE interfaces by scanning the usual IRQ/port suspects.
 *	Right now we do not scan the ide0 and ide1 address but should do so
 *	for non PCI systems or systems with no PCI IDE legacy mode devices.
 *	If you fix that note there are special cases to consider like VLB
 *	drivers and CS5510/20.
 */

static __init int legacy_init(void)
{
	int i;
	int ct = 0;
	int primary = 0;
	int secondary = 0;
	int last_port = NR_HOST;

	struct pci_dev *p = NULL;

	for_each_pci_dev(p) {
		int r;
		/* Check for any overlap of the system ATA mappings. Native mode controllers
		   stuck on these addresses or some devices in 'raid' mode won't be found by
		   the storage class test */
		for (r = 0; r < 6; r++) {
			if (pci_resource_start(p, r) == 0x1f0)
				primary = 1;
			if (pci_resource_start(p, r) == 0x170)
				secondary = 1;
		}
		/* Check for special cases */
		legacy_check_special_cases(p, &primary, &secondary);

		/* If PCI bus is present then don't probe for tertiary legacy ports */
		if (probe_all == 0)
			last_port = 2;
	}

	/* If an OPTI 82C46X is present find out where the channels are */
	if (opti82c46x) {
		static const char *optis[4] = {
			"3/463MV", "5MV",
			"5MVA", "5MVB"
		};
		u8 chans = 1;
		u8 ctrl = (opti_syscfg(0x30) & 0xC0) >> 6;

		opti82c46x = 3;	/* Assume master and slave first */
		printk(KERN_INFO DRV_NAME ": Opti 82C46%s chipset support.\n", optis[ctrl]);
		if (ctrl == 3)
			chans = (opti_syscfg(0x3F) & 0x20) ? 2 : 1;
		ctrl = opti_syscfg(0xAC);
		/* Check enabled and this port is the 465MV port. On the
		   MVB we may have two channels */
		if (ctrl & 8) {
			if (ctrl & 4)
				opti82c46x = 2;	/* Slave */
			else
				opti82c46x = 1;	/* Master */
			if (chans == 2)
				opti82c46x = 3; /* Master and Slave */
		}	/* Slave only */
		else if (chans == 1)
			opti82c46x = 1;
	}

	for (i = 0; i < last_port; i++) {
		/* Skip primary if we have seen a PCI one */
		if (i == 0 && primary == 1)
			continue;
		/* Skip secondary if we have seen a PCI one */
		if (i == 1 && secondary == 1)
			continue;
		if (legacy_init_one(i, legacy_port[i],
				   legacy_port[i] + 0x0206,
				   legacy_irq[i]) == 0)
			ct++;
	}
	if (ct != 0)
		return 0;
	return -ENODEV;
}

static __exit void legacy_exit(void)
{
	int i;

	for (i = 0; i < nr_legacy_host; i++) {
		struct legacy_data *ld = &legacy_data[i];
		struct ata_port *ap =legacy_host[i]->ports[0];
		unsigned long io = ap->ioaddr.cmd_addr;
		unsigned long ctrl = ap->ioaddr.ctl_addr;
		ata_host_remove(legacy_host[i]);
		platform_device_unregister(ld->platform_dev);
		if (ld->timing)
			release_region(ld->timing, 2);
		release_region(io, 8);
		release_region(ctrl, 1);
	}
}

MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for legacy ATA");
MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_VERSION);

module_param(probe_all, int, 0);
module_param(autospeed, int, 0);
module_param(ht6560a, int, 0);
module_param(ht6560b, int, 0);
module_param(opti82c611a, int, 0);
module_param(opti82c46x, int, 0);
module_param(pio_mask, int, 0);

module_init(legacy_init);
module_exit(legacy_exit);