drivers/input/touchscreen/gt9xx/gt9xx.c

/* drivers/input/touchscreen/gt9xx.c
 *
 * Copyright (c) 2013, The Linux Foundation. All rights reserved.
 *
 * Linux Foundation chooses to take subject only to the GPLv2 license
 * terms, and distributes only under these terms.
 *
 * 2010 - 2013 Goodix Technology.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be a reference
 * to you, when you are integrating the GOODiX's CTP IC into your system,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 * General Public License for more details.
 *
 * Version: 1.8
 * Authors: andrew@goodix.com, meta@goodix.com
 * Release Date: 2013/04/25
 * Revision record:
 *      V1.0:
 *          first Release. By Andrew, 2012/08/31
 *      V1.2:
 *          modify gtp_reset_guitar,slot report,tracking_id & 0x0F.
 *                  By Andrew, 2012/10/15
 *      V1.4:
 *          modify gt9xx_update.c. By Andrew, 2012/12/12
 *      V1.6:
 *          1. new heartbeat/esd_protect mechanism(add external watchdog)
 *          2. doze mode, sliding wakeup
 *          3. 3 more cfg_group(GT9 Sensor_ID: 0~5)
 *          3. config length verification
 *          4. names & comments
 *                  By Meta, 2013/03/11
 *      V1.8:
 *          1. pen/stylus identification
 *          2. read double check & fixed config support
 *          2. new esd & slide wakeup optimization
 *                  By Meta, 2013/06/08
 */

#include <linux/regulator/consumer.h>
#include "gt9xx.h"

#include <linux/of_gpio.h>

#include <linux/input/mt.h>

#define GOODIX_DEV_NAME	"Goodix-CTP"
#define CFG_MAX_TOUCH_POINTS	5
#define GOODIX_COORDS_ARR_SIZE	4
#define MAX_BUTTONS		4

/* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */
#define GTP_I2C_ADDRESS_HIGH	0x14
#define GTP_I2C_ADDRESS_LOW	0x5D
#define CFG_GROUP_LEN(p_cfg_grp)  (sizeof(p_cfg_grp) / sizeof(p_cfg_grp[0]))

#define GOODIX_VTG_MIN_UV	2600000
#define GOODIX_VTG_MAX_UV	3300000
#define GOODIX_I2C_VTG_MIN_UV	1800000
#define GOODIX_I2C_VTG_MAX_UV	1800000
#define GOODIX_VDD_LOAD_MIN_UA	0
#define GOODIX_VDD_LOAD_MAX_UA	10000
#define GOODIX_VIO_LOAD_MIN_UA	0
#define GOODIX_VIO_LOAD_MAX_UA	10000

#define RESET_DELAY_T3_US	200	/* T3: > 100us */
#define RESET_DELAY_T4		20	/* T4: > 5ms */

#define PHY_BUF_SIZE		32
#define PROP_NAME_SIZE		24

#define GTP_MAX_TOUCH		5
#define GTP_ESD_CHECK_CIRCLE_MS	2000

#if GTP_HAVE_TOUCH_KEY
static const u16 touch_key_array[] = {KEY_MENU, KEY_HOMEPAGE, KEY_BACK};
#define GTP_MAX_KEY_NUM  (sizeof(touch_key_array)/sizeof(touch_key_array[0]))

#if GTP_DEBUG_ON
static const int  key_codes[] = {
	KEY_HOME, KEY_BACK, KEY_MENU, KEY_SEARCH
};
static const char *const key_names[] = {
	"Key_Home", "Key_Back", "Key_Menu", "Key_Search"
};
#endif
#endif

static void gtp_reset_guitar(struct goodix_ts_data *ts, int ms);
static void gtp_int_sync(struct goodix_ts_data *ts, int ms);
static int gtp_i2c_test(struct i2c_client *client);
static int goodix_power_off(struct goodix_ts_data *ts);
static int goodix_power_on(struct goodix_ts_data *ts);

#if defined(CONFIG_FB)
static int fb_notifier_callback(struct notifier_block *self,
				 unsigned long event, void *data);
#elif defined(CONFIG_HAS_EARLYSUSPEND)
static void goodix_ts_early_suspend(struct early_suspend *h);
static void goodix_ts_late_resume(struct early_suspend *h);
#endif

#if GTP_ESD_PROTECT
static struct delayed_work gtp_esd_check_work;
static struct workqueue_struct *gtp_esd_check_workqueue;
static void gtp_esd_check_func(struct work_struct *work);
static int gtp_init_ext_watchdog(struct i2c_client *client);
struct i2c_client  *i2c_connect_client;
#endif

#if GTP_SLIDE_WAKEUP
enum doze_status {
	DOZE_DISABLED = 0,
	DOZE_ENABLED = 1,
	DOZE_WAKEUP = 2,
};
static enum doze_status = DOZE_DISABLED;
static s8 gtp_enter_doze(struct goodix_ts_data *ts);
#endif
bool init_done;
static u8 chip_gt9xxs;  /* true if ic is gt9xxs, like gt915s */
u8 grp_cfg_version;

/*******************************************************
Function:
	Read data from the i2c slave device.
Input:
	client:     i2c device.
	buf[0~1]:   read start address.
	buf[2~len-1]:   read data buffer.
	len:    GTP_ADDR_LENGTH + read bytes count
Output:
	numbers of i2c_msgs to transfer:
		2: succeed, otherwise: failed
*********************************************************/
int gtp_i2c_read(struct i2c_client *client, u8 *buf, int len)
{
	struct goodix_ts_data *ts = i2c_get_clientdata(client);
	struct i2c_msg msgs[2];
	int ret = -EIO;
	int retries = 0;

	msgs[0].flags = !I2C_M_RD;
	msgs[0].addr = client->addr;
	msgs[0].len = GTP_ADDR_LENGTH;
	msgs[0].buf = &buf[0];

	msgs[1].flags = I2C_M_RD;
	msgs[1].addr = client->addr;
	msgs[1].len = len - GTP_ADDR_LENGTH;
	msgs[1].buf = &buf[GTP_ADDR_LENGTH];

	while (retries < 5) {
		ret = i2c_transfer(client->adapter, msgs, 2);
		if (ret == 2)
			break;
		retries++;
	}
	if (retries >= 5) {
#if GTP_SLIDE_WAKEUP
		/* reset chip would quit doze mode */
		if (DOZE_ENABLED == doze_status)
			return ret;
#endif
		if (init_done)
			gtp_reset_guitar(ts, 10);
		else
			dev_warn(&client->dev,
				"<GTP> gtp_reset_guitar exit init_done=%d:\n",
				init_done);
	}
	return ret;
}

/*******************************************************
Function:
	Write data to the i2c slave device.
Input:
	client:     i2c device.
	buf[0~1]:   write start address.
	buf[2~len-1]:   data buffer
	len:    GTP_ADDR_LENGTH + write bytes count
Output:
	numbers of i2c_msgs to transfer:
	1: succeed, otherwise: failed
*********************************************************/
int gtp_i2c_write(struct i2c_client *client, u8 *buf, int len)
{
	struct goodix_ts_data *ts = i2c_get_clientdata(client);
	struct i2c_msg msg;
	int ret = -EIO;
	int retries = 0;

	msg.flags = !I2C_M_RD;
	msg.addr = client->addr;
	msg.len = len;
	msg.buf = buf;

	while (retries < 5) {
		ret = i2c_transfer(client->adapter, &msg, 1);
		if (ret == 1)
			break;
		retries++;
	}
	if ((retries >= 5)) {
#if GTP_SLIDE_WAKEUP
		if (DOZE_ENABLED == doze_status)
			return ret;
#endif
		if (init_done)
			gtp_reset_guitar(ts, 10);
		else
			dev_warn(&client->dev,
				"<GTP> gtp_reset_guitar exit init_done=%d:\n",
				init_done);
	}
	return ret;
}
/*******************************************************
Function:
	i2c read twice, compare the results
Input:
	client:  i2c device
	addr:    operate address
	rxbuf:   read data to store, if compare successful
	len:     bytes to read
Output:
	FAIL:    read failed
	SUCCESS: read successful
*********************************************************/
int gtp_i2c_read_dbl_check(struct i2c_client *client,
			u16 addr, u8 *rxbuf, int len)
{
	u8 buf[16] = {0};
	u8 confirm_buf[16] = {0};
	u8 retry = 0;

	while (retry++ < 3) {
		memset(buf, 0xAA, 16);
		buf[0] = (u8)(addr >> 8);
		buf[1] = (u8)(addr & 0xFF);
		gtp_i2c_read(client, buf, len + 2);

		memset(confirm_buf, 0xAB, 16);
		confirm_buf[0] = (u8)(addr >> 8);
		confirm_buf[1] = (u8)(addr & 0xFF);
		gtp_i2c_read(client, confirm_buf, len + 2);

		if (!memcmp(buf, confirm_buf, len + 2))
			break;
	}
	if (retry < 3) {
		memcpy(rxbuf, confirm_buf + 2, len);
		return SUCCESS;
	} else {
		dev_err(&client->dev,
			"i2c read 0x%04X, %d bytes, double check failed!",
			addr, len);
		return FAIL;
	}
}

/*******************************************************
Function:
	Send config data.
Input:
	client: i2c device.
Output:
	result of i2c write operation.
	> 0: succeed, otherwise: failed
*********************************************************/
static int gtp_send_cfg(struct goodix_ts_data *ts)
{
	int ret;
#if GTP_DRIVER_SEND_CFG
	int retry = 0;

	if (ts->fixed_cfg) {
		dev_dbg(&ts->client->dev,
			"Ic fixed config, no config sent!");
		ret = 2;
	} else {
		for (retry = 0; retry < 5; retry++) {
			ret = gtp_i2c_write(ts->client,
				ts->config_data,
				GTP_CONFIG_MAX_LENGTH + GTP_ADDR_LENGTH);
			if (ret > 0)
				break;
		}
	}
#endif

	return ret;
}

/*******************************************************
Function:
	Disable irq function
Input:
	ts: goodix i2c_client private data
Output:
	None.
*********************************************************/
void gtp_irq_disable(struct goodix_ts_data *ts)
{
	unsigned long irqflags;

	spin_lock_irqsave(&ts->irq_lock, irqflags);
	if (!ts->irq_is_disabled) {
		ts->irq_is_disabled = true;
		disable_irq_nosync(ts->client->irq);
	}
	spin_unlock_irqrestore(&ts->irq_lock, irqflags);
}

/*******************************************************
Function:
	Enable irq function
Input:
	ts: goodix i2c_client private data
Output:
	None.
*********************************************************/
void gtp_irq_enable(struct goodix_ts_data *ts)
{
	unsigned long irqflags = 0;

	spin_lock_irqsave(&ts->irq_lock, irqflags);
	if (ts->irq_is_disabled) {
		enable_irq(ts->client->irq);
		ts->irq_is_disabled = false;
	}
	spin_unlock_irqrestore(&ts->irq_lock, irqflags);
}

/*******************************************************
Function:
	Report touch point event
Input:
	ts: goodix i2c_client private data
	id: trackId
	x:  input x coordinate
	y:  input y coordinate
	w:  input pressure
Output:
	None.
*********************************************************/
static void gtp_touch_down(struct goodix_ts_data *ts, int id, int x, int y,
		int w)
{
#if GTP_CHANGE_X2Y
	swap(x, y);
#endif

	input_mt_slot(ts->input_dev, id);
	input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, true);
	input_report_abs(ts->input_dev, ABS_MT_POSITION_X, x);
	input_report_abs(ts->input_dev, ABS_MT_POSITION_Y, y);
	input_report_abs(ts->input_dev, ABS_MT_TOUCH_MAJOR, w);
	input_report_abs(ts->input_dev, ABS_MT_WIDTH_MAJOR, w);
}

/*******************************************************
Function:
	Report touch release event
Input:
	ts: goodix i2c_client private data
Output:
	None.
*********************************************************/
static void gtp_touch_up(struct goodix_ts_data *ts, int id)
{
	input_mt_slot(ts->input_dev, id);
	input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, false);
}



/*******************************************************
Function:
	Goodix touchscreen work function
Input:
	work: work struct of goodix_workqueue
Output:
	None.
*********************************************************/
static void goodix_ts_work_func(struct work_struct *work)
{
	u8 end_cmd[3] = { GTP_READ_COOR_ADDR >> 8,
			GTP_READ_COOR_ADDR & 0xFF, 0};
	u8 point_data[2 + 1 + 8 * GTP_MAX_TOUCH + 1] = {
			GTP_READ_COOR_ADDR >> 8,
			GTP_READ_COOR_ADDR & 0xFF};
	u8 touch_num = 0;
	u8 finger = 0;
	static u16 pre_touch;
	static u8 pre_key;
#if GTP_WITH_PEN
	static u8 pre_pen;
#endif
	u8 key_value = 0;
	u8 *coor_data = NULL;
	s32 input_x = 0;
	s32 input_y = 0;
	s32 input_w = 0;
	s32 id = 0;
	s32 i = 0;
	int ret = -1;
	struct goodix_ts_data *ts = NULL;

#if GTP_SLIDE_WAKEUP
	u8 doze_buf[3] = {0x81, 0x4B};
#endif

	ts = container_of(work, struct goodix_ts_data, work);
#ifdef CONFIG_GT9XX_TOUCHPANEL_UPDATE
	if (ts->enter_update)
		return;
#endif

#if GTP_SLIDE_WAKEUP
	if (DOZE_ENABLED == doze_status) {
		ret = gtp_i2c_read(ts->client, doze_buf, 3);
		if (ret > 0) {
			if (doze_buf[2] == 0xAA) {
				dev_dbg(&ts->client->dev,
					"Slide(0xAA) To Light up the screen!");
				doze_status = DOZE_WAKEUP;
				input_report_key(
					ts->input_dev, KEY_POWER, 1);
				input_sync(ts->input_dev);
				input_report_key(
					ts->input_dev, KEY_POWER, 0);
				input_sync(ts->input_dev);
				/* clear 0x814B */
				doze_buf[2] = 0x00;
				gtp_i2c_write(ts->client, doze_buf, 3);
			} else if (doze_buf[2] == 0xBB) {
				dev_dbg(&ts->client->dev,
					"Slide(0xBB) To Light up the screen!");
				doze_status = DOZE_WAKEUP;
				input_report_key(ts->input_dev, KEY_POWER, 1);
				input_sync(ts->input_dev);
				input_report_key(ts->input_dev, KEY_POWER, 0);
				input_sync(ts->input_dev);
				/* clear 0x814B*/
				doze_buf[2] = 0x00;
				gtp_i2c_write(ts->client, doze_buf, 3);
			} else if (0xC0 == (doze_buf[2] & 0xC0)) {
				dev_dbg(&ts->client->dev,
					"double click to light up the screen!");
				doze_status = DOZE_WAKEUP;
				input_report_key(ts->input_dev, KEY_POWER, 1);
				input_sync(ts->input_dev);
				input_report_key(ts->input_dev, KEY_POWER, 0);
				input_sync(ts->input_dev);
				/* clear 0x814B */
				doze_buf[2] = 0x00;
				gtp_i2c_write(ts->client, doze_buf, 3);
			} else {
				gtp_enter_doze(ts);
			}
		}
		if (ts->use_irq)
			gtp_irq_enable(ts);

		return;
	}
#endif

	ret = gtp_i2c_read(ts->client, point_data, 12);
	if (ret < 0) {
		dev_err(&ts->client->dev,
				"I2C transfer error. errno:%d\n ", ret);
		goto exit_work_func;
	}

	finger = point_data[GTP_ADDR_LENGTH];
	if ((finger & 0x80) == 0)
		goto exit_work_func;

	touch_num = finger & 0x0f;
	if (touch_num > GTP_MAX_TOUCH)
		goto exit_work_func;

	if (touch_num > 1) {
		u8 buf[8 * GTP_MAX_TOUCH] = { (GTP_READ_COOR_ADDR + 10) >> 8,
				(GTP_READ_COOR_ADDR + 10) & 0xff };

		ret = gtp_i2c_read(ts->client, buf,
				2 + 8 * (touch_num - 1));
		memcpy(&point_data[12], &buf[2], 8 * (touch_num - 1));
	}

#if GTP_HAVE_TOUCH_KEY
	key_value = point_data[3 + 8 * touch_num];

	if (key_value || pre_key) {
		for (i = 0; i < GTP_MAX_KEY_NUM; i++) {

#if GTP_DEBUG_ON
			for (ret = 0; ret < 4; ++ret) {
				if (key_codes[ret] == touch_key_array[i]) {
					GTP_DEBUG("Key: %s %s",
						key_names[ret],
						(key_value & (0x01 << i))
						? "Down" : "Up");
					break;
				}
			}
#endif

			input_report_key(ts->input_dev,
				touch_key_array[i], key_value & (0x01<<i));
		}
		touch_num = 0;
		pre_touch = 0;
	}
#endif
	pre_key = key_value;

#if GTP_WITH_PEN
	if (pre_pen && (touch_num == 0)) {
		dev_dbg(&ts->client->dev, "Pen touch UP(Slot)!");
		input_report_key(ts->input_dev, BTN_TOOL_PEN, 0);
		input_mt_slot(ts->input_dev, 5);
		input_report_abs(ts->input_dev, ABS_MT_TRACKING_ID, -1);
		pre_pen = 0;
	}
#endif
	if (pre_touch || touch_num) {
		s32 pos = 0;
		u16 touch_index = 0;

		coor_data = &point_data[3];
		if (touch_num) {
			id = coor_data[pos] & 0x0F;
#if GTP_WITH_PEN
			id = coor_data[pos];
			if (id == 128) {
				dev_dbg(&ts->client->dev,
						"Pen touch DOWN(Slot)!");
				input_x  = coor_data[pos + 1]
					| (coor_data[pos + 2] << 8);
				input_y  = coor_data[pos + 3]
					| (coor_data[pos + 4] << 8);
				input_w  = coor_data[pos + 5]
					| (coor_data[pos + 6] << 8);

				input_report_key(ts->input_dev,
					BTN_TOOL_PEN, 1);
				input_mt_slot(ts->input_dev, 5);
				input_report_abs(ts->input_dev,
					ABS_MT_TRACKING_ID, 5);
				input_report_abs(ts->input_dev,
					ABS_MT_POSITION_X, input_x);
				input_report_abs(ts->input_dev,
					ABS_MT_POSITION_Y, input_y);
				input_report_abs(ts->input_dev,
					ABS_MT_TOUCH_MAJOR, input_w);
				dev_dbg(&ts->client->dev,
					"Pen/Stylus: (%d, %d)[%d]",
					input_x, input_y, input_w);
				pre_pen = 1;
				pre_touch = 0;
			}
#endif

			touch_index |= (0x01<<id);
		}

		for (i = 0; i < GTP_MAX_TOUCH; i++) {
#if GTP_WITH_PEN
			if (pre_pen == 1)
				break;
#endif
			if (touch_index & (0x01<<i)) {
				input_x = coor_data[pos + 1] |
						coor_data[pos + 2] << 8;
				input_y = coor_data[pos + 3] |
						coor_data[pos + 4] << 8;
				input_w = coor_data[pos + 5] |
						coor_data[pos + 6] << 8;

				gtp_touch_down(ts, id,
						input_x, input_y, input_w);
				pre_touch |= 0x01 << i;

				pos += 8;
				id = coor_data[pos] & 0x0F;
				touch_index |= (0x01<<id);
			} else {
				gtp_touch_up(ts, i);
				pre_touch &= ~(0x01 << i);
			}
		}
	}
	input_sync(ts->input_dev);

exit_work_func:
	if (!ts->gtp_rawdiff_mode) {
		ret = gtp_i2c_write(ts->client, end_cmd, 3);
		if (ret < 0)
			dev_warn(&ts->client->dev, "I2C write end_cmd error!\n");

	}
	if (ts->use_irq)
		gtp_irq_enable(ts);

	return;
}

/*******************************************************
Function:
	Timer interrupt service routine for polling mode.
Input:
	timer: timer struct pointer
Output:
	Timer work mode.
	HRTIMER_NORESTART: no restart mode
*********************************************************/
static enum hrtimer_restart goodix_ts_timer_handler(struct hrtimer *timer)
{
	struct goodix_ts_data
		*ts = container_of(timer, struct goodix_ts_data, timer);

	queue_work(ts->goodix_wq, &ts->work);
	hrtimer_start(&ts->timer, ktime_set(0, (GTP_POLL_TIME + 6) * 1000000),
			HRTIMER_MODE_REL);
	return HRTIMER_NORESTART;
}

/*******************************************************
Function:
	External interrupt service routine for interrupt mode.
Input:
	irq:  interrupt number.
	dev_id: private data pointer
Output:
	Handle Result.
	IRQ_HANDLED: interrupt handled successfully
*********************************************************/
static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
{
	struct goodix_ts_data *ts = dev_id;

	gtp_irq_disable(ts);

	queue_work(ts->goodix_wq, &ts->work);

	return IRQ_HANDLED;
}
/*******************************************************
Function:
	Synchronization.
Input:
	ms: synchronization time in millisecond.
Output:
	None.
*******************************************************/
void gtp_int_sync(struct goodix_ts_data *ts, int ms)
{
	gpio_direction_output(ts->pdata->irq_gpio, 0);
	msleep(ms);
	gpio_direction_input(ts->pdata->irq_gpio);
}

/*******************************************************
Function:
	Reset chip.
Input:
	ms: reset time in millisecond, must >10ms
Output:
	None.
*******************************************************/
static void gtp_reset_guitar(struct goodix_ts_data *ts, int ms)
{
	/* This reset sequence will selcet I2C slave address */
	gpio_direction_output(ts->pdata->reset_gpio, 0);
	msleep(ms);

	if (ts->client->addr == GTP_I2C_ADDRESS_HIGH)
		gpio_direction_output(ts->pdata->irq_gpio, 1);
	else
		gpio_direction_output(ts->pdata->irq_gpio, 0);

	usleep(RESET_DELAY_T3_US);
	gpio_direction_output(ts->pdata->reset_gpio, 1);
	msleep(RESET_DELAY_T4);

	gpio_direction_input(ts->pdata->reset_gpio);

	gtp_int_sync(ts, 50);

#if GTP_ESD_PROTECT
	gtp_init_ext_watchdog(ts->client);
#endif
}

#if defined(CONFIG_HAS_EARLYSUSPEND) || defined(CONFIG_FB)
#if GTP_SLIDE_WAKEUP
/*******************************************************
Function:
	Enter doze mode for sliding wakeup.
Input:
	ts: goodix tp private data
Output:
	1: succeed, otherwise failed
*******************************************************/
static s8 gtp_enter_doze(struct goodix_ts_data *ts)
{
	int ret = -1;
	s8 retry = 0;
	u8 i2c_control_buf[3] = {
		(u8)(GTP_REG_SLEEP >> 8),
		(u8)GTP_REG_SLEEP, 8};

#if GTP_DBL_CLK_WAKEUP
	i2c_control_buf[2] = 0x09;
#endif
	gtp_irq_disable(ts);

	while (retry++ < 5) {
		i2c_control_buf[0] = 0x80;
		i2c_control_buf[1] = 0x46;
		ret = gtp_i2c_write(ts->client, i2c_control_buf, 3);
		if (ret < 0) {
			dev_err(&ts->client->dev,
				"failed to set doze flag into 0x8046, %d",
				retry);
			continue;
		}
		i2c_control_buf[0] = 0x80;
		i2c_control_buf[1] = 0x40;
		ret = gtp_i2c_write(ts->client, i2c_control_buf, 3);
		if (ret > 0) {
			doze_status = DOZE_ENABLED;
			dev_dbg(&ts->client->dev,
				"GTP has been working in doze mode!");
			gtp_irq_enable(ts);
			return ret;
		}
		msleep(20);
	}
	dev_err(&ts->client->dev, "GTP send doze cmd failed.\n");
	gtp_irq_enable(ts);
	return ret;
}
#else
/**
 * gtp_enter_sleep - Enter sleep mode
 * @ts: driver private data
 *
 * Returns zero on success, else an error.
 */
static u8 gtp_enter_sleep(struct goodix_ts_data *ts)
{
	int ret = -1;
	s8 retry = 0;
	u8 i2c_control_buf[3] = {
		(u8)(GTP_REG_SLEEP >> 8),
		(u8)GTP_REG_SLEEP, 5};

	ret = gpio_direction_output(ts->pdata->irq_gpio, 0);
	if (ret)
		dev_err(&ts->client->dev,
			"GTP sleep: Cannot reconfig gpio %d.\n",
			ts->pdata->irq_gpio);
	if (ts->pdata->enable_power_off) {
		ret = gpio_direction_output(ts->pdata->reset_gpio, 0);
		if (ret)
			dev_err(&ts->client->dev,
				"GTP sleep: Cannot reconfig gpio %d.\n",
				ts->pdata->reset_gpio);
		ret = goodix_power_off(ts);
		if (ret) {
			dev_err(&ts->client->dev, "GTP power off failed.\n");
			return ret;
		}
		return 0;
	} else {
		usleep(5000);
		while (retry++ < 5) {
			ret = gtp_i2c_write(ts->client, i2c_control_buf, 3);
			if (ret == 1) {
				dev_dbg(&ts->client->dev, "GTP enter sleep!");
				return 0;
			}
			msleep(20);
		}
		dev_err(&ts->client->dev, "GTP send sleep cmd failed.\n");
		return ret;
	}
}
#endif /* !GTP_SLIDE_WAKEUP */

/*******************************************************
Function:
	Wakeup from sleep.
Input:
	ts: private data.
Output:
	Executive outcomes.
	>0: succeed, otherwise: failed.
*******************************************************/
static s8 gtp_wakeup_sleep(struct goodix_ts_data *ts)
{
	u8 retry = 0;
	s8 ret = -1;

	if (ts->pdata->enable_power_off) {
		ret = gpio_direction_output(ts->pdata->irq_gpio, 0);
		if (ret)
			dev_err(&ts->client->dev,
				"GTP wakeup: Cannot reconfig gpio %d.\n",
				ts->pdata->irq_gpio);
		ret = gpio_direction_output(ts->pdata->reset_gpio, 0);
		if (ret)
			dev_err(&ts->client->dev,
				"GTP wakeup: Cannot reconfig gpio %d.\n",
				ts->pdata->reset_gpio);
		ret = goodix_power_on(ts);
		if (ret) {
			dev_err(&ts->client->dev, "GTP power on failed.\n");
			return 0;
		}

		gtp_reset_guitar(ts, 20);

		ret = gtp_send_cfg(ts);
		if (ret <= 0) {
			dev_err(&ts->client->dev,
				"GTP wakeup sleep failed.\n");
			return ret;
		}

		dev_dbg(&ts->client->dev,
				"Wakeup sleep send config success.");
	} else {
err_retry:
#if GTP_SLIDE_WAKEUP
		/* wakeup not by slide */
		if (DOZE_WAKEUP != doze_status)
			gtp_reset_guitar(ts, 10);
		else
			/* wakeup by slide */
			doze_status = DOZE_DISABLED;
#else
		if (chip_gt9xxs == 1) {
			gtp_reset_guitar(ts, 10);
		} else {
			ret = gpio_direction_output(ts->pdata->irq_gpio, 1);
			usleep(5000);
		}
#endif
		ret = gtp_i2c_test(ts->client);
		if (ret == 2) {
			dev_dbg(&ts->client->dev, "GTP wakeup sleep.");
#if (!GTP_SLIDE_WAKEUP)
			if (chip_gt9xxs == 0) {
				gtp_int_sync(ts, 25);
				msleep(20);
#if GTP_ESD_PROTECT
				gtp_init_ext_watchdog(ts->client);
#endif
			}
#endif
			return ret;
		}
		gtp_reset_guitar(ts, 20);
		if (retry++ < 10)
			goto err_retry;
		dev_err(&ts->client->dev, "GTP wakeup sleep failed.\n");
	}
	return ret;
}
#endif /* !CONFIG_HAS_EARLYSUSPEND && !CONFIG_FB*/

/*******************************************************
Function:
	Initialize gtp.
Input:
	ts: goodix private data
Output:
	Executive outcomes.
	> =0: succeed, otherwise: failed
*******************************************************/
static int gtp_init_panel(struct goodix_ts_data *ts)
{
	struct i2c_client *client = ts->client;
	unsigned char *config_data;
	int ret = -EIO;

#if GTP_DRIVER_SEND_CFG
	int i;
	u8 check_sum = 0;
	u8 opr_buf[16];
	u8 sensor_id = 0;

	for (i = 0; i < GOODIX_MAX_CFG_GROUP; i++)
		dev_dbg(&client->dev, "Config Groups(%d) Lengths: %d",
			i, ts->pdata->config_data_len[i]);

	ret = gtp_i2c_read_dbl_check(ts->client, 0x41E4, opr_buf, 1);
	if (SUCCESS == ret) {
		if (opr_buf[0] != 0xBE) {
			ts->fw_error = 1;
			dev_err(&client->dev,
				"Firmware error, no config sent!");
			return -EINVAL;
		}
	}

	for (i = 1; i < GOODIX_MAX_CFG_GROUP; i++) {
		if (ts->pdata->config_data_len[i])
			break;
	}
	if (i == GOODIX_MAX_CFG_GROUP) {
		sensor_id = 0;
	} else {
		ret = gtp_i2c_read_dbl_check(ts->client, GTP_REG_SENSOR_ID,
			&sensor_id, 1);
		if (SUCCESS == ret) {
			if (sensor_id >= GOODIX_MAX_CFG_GROUP) {
				dev_err(&client->dev,
					"Invalid sensor_id(0x%02X), No Config Sent!",
					sensor_id);
				return -EINVAL;
			}
		} else {
			dev_err(&client->dev,
				"Failed to get sensor_id, No config sent!");
			return -EINVAL;
		}
	}

	dev_info(&client->dev, "Sensor ID selected: %d", sensor_id);

	if (ts->pdata->config_data_len[sensor_id] < GTP_CONFIG_MIN_LENGTH ||
		!ts->pdata->config_data[sensor_id]) {
		dev_err(&client->dev,
				"Sensor_ID(%d) matches with NULL or invalid config group!\n",
				sensor_id);
		return -EINVAL;
	}

	ret = gtp_i2c_read_dbl_check(ts->client, GTP_REG_CONFIG_DATA,
		&opr_buf[0], 1);
	if (ret == SUCCESS) {
		if (opr_buf[0] < 90) {
			/* backup group config version */
			grp_cfg_version =
			ts->pdata->config_data[sensor_id][GTP_ADDR_LENGTH];
			ts->pdata->config_data[sensor_id][GTP_ADDR_LENGTH] =
				0x00;
			ts->fixed_cfg = 0;
		} else {
			/* treated as fixed config, not send config */
			dev_warn(&client->dev,
				"Ic fixed config with config version(%d, 0x%02X)",
				opr_buf[0], opr_buf[0]);
			ts->fixed_cfg = 1;
		}
	} else {
		dev_err(&client->dev,
			"Failed to get ic config version!No config sent!");
		return -EINVAL;
	}

	config_data = ts->pdata->config_data[sensor_id];
	ts->config_data = ts->pdata->config_data[sensor_id];
	ts->gtp_cfg_len = ts->pdata->config_data_len[sensor_id];

#if GTP_CUSTOM_CFG
	config_data[RESOLUTION_LOC] =
	(unsigned char)(GTP_MAX_WIDTH && 0xFF);
	config_data[RESOLUTION_LOC + 1] =
	(unsigned char)(GTP_MAX_WIDTH >> 8);
	config_data[RESOLUTION_LOC + 2] =
	(unsigned char)(GTP_MAX_HEIGHT && 0xFF);
	config_data[RESOLUTION_LOC + 3] =
	(unsigned char)(GTP_MAX_HEIGHT >> 8);

	if (GTP_INT_TRIGGER == 0)
		config_data[TRIGGER_LOC] &= 0xfe;
	else if (GTP_INT_TRIGGER == 1)
		config_data[TRIGGER_LOC] |= 0x01;
#endif  /* !GTP_CUSTOM_CFG */

	check_sum = 0;
	for (i = GTP_ADDR_LENGTH; i < ts->gtp_cfg_len; i++)
		check_sum += config_data[i];

	config_data[ts->gtp_cfg_len] = (~check_sum) + 1;

#else /* DRIVER NOT SEND CONFIG */
	ts->gtp_cfg_len = GTP_CONFIG_MAX_LENGTH;
	ret = gtp_i2c_read(ts->client, config_data,
			ts->gtp_cfg_len + GTP_ADDR_LENGTH);
	if (ret < 0) {
		dev_err(&client->dev,
				"Read Config Failed, Using DEFAULT Resolution & INT Trigger!\n");
		ts->abs_x_max = GTP_MAX_WIDTH;
		ts->abs_y_max = GTP_MAX_HEIGHT;
		ts->int_trigger_type = GTP_INT_TRIGGER;
	}
#endif /* !DRIVER NOT SEND CONFIG */

	if ((ts->abs_x_max == 0) && (ts->abs_y_max == 0)) {
		ts->abs_x_max = (config_data[RESOLUTION_LOC + 1] << 8)
				+ config_data[RESOLUTION_LOC];
		ts->abs_y_max = (config_data[RESOLUTION_LOC + 3] << 8)
				+ config_data[RESOLUTION_LOC + 2];
		ts->int_trigger_type = (config_data[TRIGGER_LOC]) & 0x03;
	}
	ret = gtp_send_cfg(ts);
	if (ret < 0)
		dev_err(&client->dev, "%s: Send config error.\n", __func__);

	msleep(20);
	return ret;
}

/*******************************************************
Function:
	Read firmware version
Input:
	client:  i2c device
	version: buffer to keep ic firmware version
Output:
	read operation return.
	0: succeed, otherwise: failed
*******************************************************/
static int gtp_read_fw_version(struct i2c_client *client, u16 *version)
{
	int ret = 0;
	u8 buf[GTP_FW_VERSION_BUFFER_MAXSIZE] = {
		GTP_REG_FW_VERSION >> 8, GTP_REG_FW_VERSION & 0xff };

	ret = gtp_i2c_read(client, buf, sizeof(buf));
	if (ret < 0) {
		dev_err(&client->dev, "GTP read version failed.\n");
		return -EIO;
	}

	if (version)
		*version = (buf[3] << 8) | buf[2];

	return ret;
}
/*******************************************************
Function:
	Read and check chip id.
Input:
	client:  i2c device
Output:
	read operation return.
	0: succeed, otherwise: failed
*******************************************************/
static int gtp_check_product_id(struct i2c_client *client)
{
	int ret = 0;
	char product_id[GTP_PRODUCT_ID_MAXSIZE];
	struct goodix_ts_data *ts = i2c_get_clientdata(client);
	/* 04 bytes are used for the Product-id in the register space.*/
	u8 buf[GTP_PRODUCT_ID_BUFFER_MAXSIZE] =	{
		GTP_REG_PRODUCT_ID >> 8, GTP_REG_PRODUCT_ID & 0xff };

	ret = gtp_i2c_read(client, buf, sizeof(buf));
	if (ret < 0) {
		dev_err(&client->dev, "GTP read version failed.\n");
		return -EIO;
	}

	if (buf[5] == 0x00) {
		/* copy (GTP_PRODUCT_ID_MAXSIZE - 1) from buffer. Ex: 915 */
		strlcpy(product_id, &buf[2], GTP_PRODUCT_ID_MAXSIZE - 1);
	} else {
		if (buf[5] == 'S' || buf[5] == 's')
			chip_gt9xxs = 1;
		/* copy GTP_PRODUCT_ID_MAXSIZE from buffer. Ex: 915s */
		strlcpy(product_id, &buf[2], GTP_PRODUCT_ID_MAXSIZE);
	}

	dev_info(&client->dev, "Goodix Product ID = %s\n", product_id);

	ret = strcmp(product_id, ts->pdata->product_id);
	if (ret != 0)
		return -EINVAL;

	return ret;
}

/*******************************************************
Function:
	I2c test Function.
Input:
	client:i2c client.
Output:
	Executive outcomes.
	2: succeed, otherwise failed.
*******************************************************/
static int gtp_i2c_test(struct i2c_client *client)
{
	u8 buf[3] = { GTP_REG_CONFIG_DATA >> 8, GTP_REG_CONFIG_DATA & 0xff };
	int retry = 5;
	int ret = -EIO;

	while (retry--) {
		ret = gtp_i2c_read(client, buf, 3);
		if (ret > 0)
			return ret;
		dev_err(&client->dev, "GTP i2c test failed time %d.\n", retry);
		msleep(20);
	}
	return ret;
}

/*******************************************************
Function:
	Request gpio(INT & RST) ports.
Input:
	ts: private data.
Output:
	Executive outcomes.
	= 0: succeed, != 0: failed
*******************************************************/
static int gtp_request_io_port(struct goodix_ts_data *ts)
{
	struct i2c_client *client = ts->client;
	struct goodix_ts_platform_data *pdata = ts->pdata;
	int ret;

	if (gpio_is_valid(pdata->irq_gpio)) {
		ret = gpio_request(pdata->irq_gpio, "goodix_ts_irq_gpio");
		if (ret) {
			dev_err(&client->dev, "Unable to request irq gpio [%d]\n",
				pdata->irq_gpio);
			goto err_pwr_off;
		}
		ret = gpio_direction_input(pdata->irq_gpio);
		if (ret) {
			dev_err(&client->dev, "Unable to set direction for irq gpio [%d]\n",
				pdata->irq_gpio);
			goto err_free_irq_gpio;
		}
	} else {
		dev_err(&client->dev, "Invalid irq gpio [%d]!\n",
			pdata->irq_gpio);
		ret = -EINVAL;
		goto err_pwr_off;
	}

	if (gpio_is_valid(pdata->reset_gpio)) {
		ret = gpio_request(pdata->reset_gpio, "goodix_ts_reset_gpio");
		if (ret) {
			dev_err(&client->dev, "Unable to request reset gpio [%d]\n",
				pdata->reset_gpio);
			goto err_free_irq_gpio;
		}

		ret = gpio_direction_output(pdata->reset_gpio, 0);
		if (ret) {
			dev_err(&client->dev, "Unable to set direction for reset gpio [%d]\n",
				pdata->reset_gpio);
			goto err_free_reset_gpio;
		}
	} else {
		dev_err(&client->dev, "Invalid irq gpio [%d]!\n",
			pdata->reset_gpio);
		ret = -EINVAL;
		goto err_free_irq_gpio;
	}
	/* IRQ GPIO is an input signal, but we are setting it to output
	  * direction and pulling it down, to comply with power up timing
	  * requirements, mentioned in power up timing section of device
	  * datasheet.
	  */
	ret = gpio_direction_output(pdata->irq_gpio, 0);
	if (ret)
		dev_warn(&client->dev,
			"pull down interrupt gpio failed\n");
	ret = gpio_direction_output(pdata->reset_gpio, 0);
	if (ret)
		dev_warn(&client->dev,
			"pull down reset gpio failed\n");

	return ret;

err_free_reset_gpio:
	if (gpio_is_valid(pdata->reset_gpio))
		gpio_free(pdata->reset_gpio);
err_free_irq_gpio:
	if (gpio_is_valid(pdata->irq_gpio))
		gpio_free(pdata->irq_gpio);
err_pwr_off:
	return ret;
}

/*******************************************************
Function:
	Request interrupt.
Input:
	ts: private data.
Output:
	Executive outcomes.
	0: succeed, -1: failed.
*******************************************************/
static int gtp_request_irq(struct goodix_ts_data *ts)
{
	int ret;
	const u8 irq_table[] = GTP_IRQ_TAB;

	ret = request_threaded_irq(ts->client->irq, NULL,
			goodix_ts_irq_handler,
			irq_table[ts->int_trigger_type],
			ts->client->name, ts);
	if (ret) {
		dev_err(&ts->client->dev, "Request IRQ failed!ERRNO:%d.\n",
				ret);
		gpio_direction_input(ts->pdata->irq_gpio);

		hrtimer_init(&ts->timer, CLOCK_MONOTONIC,
				HRTIMER_MODE_REL);
		ts->timer.function = goodix_ts_timer_handler;
		hrtimer_start(&ts->timer, ktime_set(1, 0),
				HRTIMER_MODE_REL);
		ts->use_irq = false;
		return ret;
	} else {
		gtp_irq_disable(ts);
		ts->use_irq = true;
		return 0;
	}
}

/*******************************************************
Function:
	Request input device Function.
Input:
	ts:private data.
Output:
	Executive outcomes.
	0: succeed, otherwise: failed.
*******************************************************/
static int gtp_request_input_dev(struct goodix_ts_data *ts)
{
	int ret;
	char phys[PHY_BUF_SIZE];
#if GTP_HAVE_TOUCH_KEY
	int index = 0;
#endif

	ts->input_dev = input_allocate_device();
	if (ts->input_dev == NULL) {
		dev_err(&ts->client->dev,
				"Failed to allocate input device.\n");
		return -ENOMEM;
	}

	ts->input_dev->evbit[0] =
		BIT_MASK(EV_SYN) | BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS) ;
	set_bit(BTN_TOOL_FINGER, ts->input_dev->keybit);
	__set_bit(INPUT_PROP_DIRECT, ts->input_dev->propbit);
	input_mt_init_slots(ts->input_dev, 10);/* in case of "out of memory" */

#if GTP_HAVE_TOUCH_KEY
	for (index = 0; index < GTP_MAX_KEY_NUM; index++) {
		input_set_capability(ts->input_dev,
				EV_KEY, touch_key_array[index]);
	}
#endif

#if GTP_SLIDE_WAKEUP
	input_set_capability(ts->input_dev, EV_KEY, KEY_POWER);
#endif

#if GTP_WITH_PEN
	/* pen support */
	__set_bit(BTN_TOOL_PEN, ts->input_dev->keybit);
	__set_bit(INPUT_PROP_DIRECT, ts->input_dev->propbit);
	__set_bit(INPUT_PROP_POINTER, ts->input_dev->propbit);
#endif

#if GTP_CHANGE_X2Y
	swap(ts->abs_x_max, ts->abs_y_max);
#endif

	input_set_abs_params(ts->input_dev, ABS_MT_POSITION_X,
				0, ts->abs_x_max, 0, 0);
	input_set_abs_params(ts->input_dev, ABS_MT_POSITION_Y,
				0, ts->abs_y_max, 0, 0);
	input_set_abs_params(ts->input_dev, ABS_MT_WIDTH_MAJOR,
				0, 255, 0, 0);
	input_set_abs_params(ts->input_dev, ABS_MT_TOUCH_MAJOR,
				0, 255, 0, 0);
	input_set_abs_params(ts->input_dev, ABS_MT_TRACKING_ID,
				0, 255, 0, 0);

	snprintf(phys, PHY_BUF_SIZE, "input/ts");
	ts->input_dev->name = GOODIX_DEV_NAME;
	ts->input_dev->phys = phys;
	ts->input_dev->id.bustype = BUS_I2C;
	ts->input_dev->id.vendor = 0xDEAD;
	ts->input_dev->id.product = 0xBEEF;
	ts->input_dev->id.version = 10427;

	ret = input_register_device(ts->input_dev);
	if (ret) {
		dev_err(&ts->client->dev,
				"Register %s input device failed.\n",
				ts->input_dev->name);
		goto exit_free_inputdev;
	}

	return 0;

exit_free_inputdev:
	input_free_device(ts->input_dev);
	ts->input_dev = NULL;
	return ret;
}

static int reg_set_optimum_mode_check(struct regulator *reg, int load_uA)
{
	return (regulator_count_voltages(reg) > 0) ?
		regulator_set_optimum_mode(reg, load_uA) : 0;
}

/**
 * goodix_power_on - Turn device power ON
 * @ts: driver private data
 *
 * Returns zero on success, else an error.
 */
static int goodix_power_on(struct goodix_ts_data *ts)
{
	int ret;

	if (ts->power_on) {
		dev_info(&ts->client->dev,
				"Device already power on\n");
		return 0;
	}

	if (!IS_ERR(ts->avdd)) {
		ret = reg_set_optimum_mode_check(ts->avdd,
			GOODIX_VDD_LOAD_MAX_UA);
		if (ret < 0) {
			dev_err(&ts->client->dev,
				"Regulator avdd set_opt failed rc=%d\n", ret);
			goto err_set_opt_avdd;
		}
		ret = regulator_enable(ts->avdd);
		if (ret) {
			dev_err(&ts->client->dev,
				"Regulator avdd enable failed ret=%d\n", ret);
			goto err_enable_avdd;
		}
	}

	if (!IS_ERR(ts->vdd)) {
		ret = regulator_set_voltage(ts->vdd, GOODIX_VTG_MIN_UV,
					   GOODIX_VTG_MAX_UV);
		if (ret) {
			dev_err(&ts->client->dev,
				"Regulator set_vtg failed vdd ret=%d\n", ret);
			goto err_set_vtg_vdd;
		}
		ret = reg_set_optimum_mode_check(ts->vdd,
			GOODIX_VDD_LOAD_MAX_UA);
		if (ret < 0) {
			dev_err(&ts->client->dev,
				"Regulator vdd set_opt failed rc=%d\n", ret);
			goto err_set_opt_vdd;
		}
		ret = regulator_enable(ts->vdd);
		if (ret) {
			dev_err(&ts->client->dev,
				"Regulator vdd enable failed ret=%d\n", ret);
			goto err_enable_vdd;
		}
	}

	if (!IS_ERR(ts->vcc_i2c)) {
		ret = regulator_set_voltage(ts->vcc_i2c, GOODIX_I2C_VTG_MIN_UV,
					   GOODIX_I2C_VTG_MAX_UV);
		if (ret) {
			dev_err(&ts->client->dev,
				"Regulator set_vtg failed vcc_i2c ret=%d\n",
				ret);
			goto err_set_vtg_vcc_i2c;
		}
		ret = reg_set_optimum_mode_check(ts->vcc_i2c,
			GOODIX_VIO_LOAD_MAX_UA);
		if (ret < 0) {
			dev_err(&ts->client->dev,
				"Regulator vcc_i2c set_opt failed rc=%d\n",
				ret);
			goto err_set_opt_vcc_i2c;
		}
		ret = regulator_enable(ts->vcc_i2c);
		if (ret) {
			dev_err(&ts->client->dev,
				"Regulator vcc_i2c enable failed ret=%d\n",
				ret);
			regulator_disable(ts->vdd);
			goto err_enable_vcc_i2c;
			}
	}

	ts->power_on = true;
	return 0;

err_enable_vcc_i2c:
err_set_opt_vcc_i2c:
	if (!IS_ERR(ts->vcc_i2c))
		regulator_set_voltage(ts->vcc_i2c, 0, GOODIX_I2C_VTG_MAX_UV);
err_set_vtg_vcc_i2c:
	if (!IS_ERR(ts->vdd))
		regulator_disable(ts->vdd);
err_enable_vdd:
err_set_opt_vdd:
	if (!IS_ERR(ts->vdd))
		regulator_set_voltage(ts->vdd, 0, GOODIX_VTG_MAX_UV);
err_set_vtg_vdd:
	if (!IS_ERR(ts->avdd))
		regulator_disable(ts->avdd);
err_enable_avdd:
err_set_opt_avdd:
	ts->power_on = false;
	return ret;
}

/**
 * goodix_power_off - Turn device power OFF
 * @ts: driver private data
 *
 * Returns zero on success, else an error.
 */
static int goodix_power_off(struct goodix_ts_data *ts)
{
	int ret;

	if (!ts->power_on) {
		dev_info(&ts->client->dev,
				"Device already power off\n");
		return 0;
	}

	if (!IS_ERR(ts->vcc_i2c)) {
		ret = regulator_set_voltage(ts->vcc_i2c, 0,
			GOODIX_I2C_VTG_MAX_UV);
		if (ret < 0)
			dev_err(&ts->client->dev,
				"Regulator vcc_i2c set_vtg failed ret=%d\n",
				ret);
		ret = regulator_disable(ts->vcc_i2c);
		if (ret)
			dev_err(&ts->client->dev,
				"Regulator vcc_i2c disable failed ret=%d\n",
				ret);
	}

	if (!IS_ERR(ts->vdd)) {
		ret = regulator_set_voltage(ts->vdd, 0, GOODIX_VTG_MAX_UV);
		if (ret < 0)
			dev_err(&ts->client->dev,
				"Regulator vdd set_vtg failed ret=%d\n", ret);
		ret = regulator_disable(ts->vdd);
		if (ret)
			dev_err(&ts->client->dev,
				"Regulator vdd disable failed ret=%d\n", ret);
	}

	if (!IS_ERR(ts->avdd)) {
		ret = regulator_disable(ts->avdd);
		if (ret)
			dev_err(&ts->client->dev,
				"Regulator avdd disable failed ret=%d\n", ret);
	}

	ts->power_on = false;
	return 0;
}

/**
 * goodix_power_init - Initialize device power
 * @ts: driver private data
 *
 * Returns zero on success, else an error.
 */
static int goodix_power_init(struct goodix_ts_data *ts)
{
	int ret;

	ts->avdd = regulator_get(&ts->client->dev, "avdd");
	if (IS_ERR(ts->avdd)) {
		ret = PTR_ERR(ts->avdd);
		dev_info(&ts->client->dev,
			"Regulator get failed avdd ret=%d\n", ret);
	}

	ts->vdd = regulator_get(&ts->client->dev, "vdd");
	if (IS_ERR(ts->vdd)) {
		ret = PTR_ERR(ts->vdd);
		dev_info(&ts->client->dev,
			"Regulator get failed vdd ret=%d\n", ret);
	}

	ts->vcc_i2c = regulator_get(&ts->client->dev, "vcc-i2c");
	if (IS_ERR(ts->vcc_i2c)) {
		ret = PTR_ERR(ts->vcc_i2c);
		dev_info(&ts->client->dev,
			"Regulator get failed vcc_i2c ret=%d\n", ret);
	}

	return 0;
}

/**
 * goodix_power_deinit - Deinitialize device power
 * @ts: driver private data
 *
 * Returns zero on success, else an error.
 */
static int goodix_power_deinit(struct goodix_ts_data *ts)
{
	regulator_put(ts->vdd);
	regulator_put(ts->vcc_i2c);
	regulator_put(ts->avdd);

	return 0;
}

static ssize_t gtp_fw_name_show(struct device *dev,
				struct device_attribute *attr, char *buf)
{
	struct goodix_ts_data *ts = dev_get_drvdata(dev);

	if (!strlen(ts->fw_name))
		return snprintf(buf, GTP_FW_NAME_MAXSIZE - 1,
			"No fw name has been given.");
	else
		return snprintf(buf, GTP_FW_NAME_MAXSIZE - 1,
			"%s\n", ts->fw_name);
}

static ssize_t gtp_fw_name_store(struct device *dev,
				struct device_attribute *attr,
				const char *buf, size_t size)
{
	struct goodix_ts_data *ts = dev_get_drvdata(dev);

	if (size > GTP_FW_NAME_MAXSIZE - 1) {
		dev_err(dev, "FW name size exceeds the limit.");
		return -EINVAL;
	}

	strlcpy(ts->fw_name, buf, size);
	if (ts->fw_name[size-1] == '\n')
		ts->fw_name[size-1] = '\0';

	return size;
}

static DEVICE_ATTR(fw_name, (S_IRUGO | S_IWUSR | S_IWGRP),
			gtp_fw_name_show,
			gtp_fw_name_store);

static struct attribute *gtp_attrs[] = {
	&dev_attr_fw_name.attr,
	NULL
};

static const struct attribute_group gtp_attr_grp = {
	.attrs = gtp_attrs,
};

static int goodix_ts_get_dt_coords(struct device *dev, char *name,
				struct goodix_ts_platform_data *pdata)
{
	struct property *prop;
	struct device_node *np = dev->of_node;
	int rc;
	u32 coords[GOODIX_COORDS_ARR_SIZE];

	prop = of_find_property(np, name, NULL);
	if (!prop)
		return -EINVAL;
	if (!prop->value)
		return -ENODATA;

	rc = of_property_read_u32_array(np, name, coords,
		GOODIX_COORDS_ARR_SIZE);
	if (rc && (rc != -EINVAL)) {
		dev_err(dev, "Unable to read %s\n", name);
		return rc;
	}

	if (!strcmp(name, "goodix,panel-coords")) {
		pdata->panel_minx = coords[0];
		pdata->panel_miny = coords[1];
		pdata->panel_maxx = coords[2];
		pdata->panel_maxy = coords[3];
	} else if (!strcmp(name, "goodix,display-coords")) {
		pdata->x_min = coords[0];
		pdata->y_min = coords[1];
		pdata->x_max = coords[2];
		pdata->y_max = coords[3];
	} else {
		dev_err(dev, "unsupported property %s\n", name);
		return -EINVAL;
	}

	return 0;
}

static int goodix_parse_dt(struct device *dev,
			struct goodix_ts_platform_data *pdata)
{
	int rc;
	struct device_node *np = dev->of_node;
	struct property *prop;
	u32 temp_val, num_buttons;
	u32 button_map[MAX_BUTTONS];
	char prop_name[PROP_NAME_SIZE];
	int i, read_cfg_num;

	rc = goodix_ts_get_dt_coords(dev, "goodix,panel-coords", pdata);
	if (rc && (rc != -EINVAL))
		return rc;

	rc = goodix_ts_get_dt_coords(dev, "goodix,display-coords", pdata);
	if (rc)
		return rc;

	pdata->i2c_pull_up = of_property_read_bool(np,
						"goodix,i2c-pull-up");

	pdata->no_force_update = of_property_read_bool(np,
						"goodix,no-force-update");

	pdata->enable_power_off = of_property_read_bool(np,
						"goodix,enable-power-off");
	/* reset, irq gpio info */
	pdata->reset_gpio = of_get_named_gpio_flags(np, "reset-gpios",
				0, &pdata->reset_gpio_flags);
	if (pdata->reset_gpio < 0)
		return pdata->reset_gpio;

	pdata->irq_gpio = of_get_named_gpio_flags(np, "interrupt-gpios",
				0, &pdata->irq_gpio_flags);
	if (pdata->irq_gpio < 0)
		return pdata->irq_gpio;

	rc = of_property_read_string(np, "goodix,product-id",
						&pdata->product_id);
	if (rc && (rc != -EINVAL)) {
		dev_err(dev, "Failed to parse product_id.");
		return -EINVAL;
	}

	rc = of_property_read_string(np, "goodix,fw_name",
						&pdata->fw_name);
	if (rc && (rc != -EINVAL)) {
		dev_err(dev, "Failed to parse firmware name.\n");
		return -EINVAL;
	}

	prop = of_find_property(np, "goodix,button-map", NULL);
	if (prop) {
		num_buttons = prop->length / sizeof(temp_val);
		if (num_buttons > MAX_BUTTONS)
			return -EINVAL;

		rc = of_property_read_u32_array(np,
			"goodix,button-map", button_map,
			num_buttons);
		if (rc) {
			dev_err(dev, "Unable to read key codes\n");
			return rc;
		}
	}

	read_cfg_num = 0;
	for (i = 0; i < GOODIX_MAX_CFG_GROUP; i++) {
		snprintf(prop_name, sizeof(prop_name), "goodix,cfg-data%d", i);
		prop = of_find_property(np, prop_name,
			&pdata->config_data_len[i]);
		if (!prop || !prop->value) {
			pdata->config_data_len[i] = 0;
			pdata->config_data[i] = NULL;
			continue;
		}
		pdata->config_data[i] = devm_kzalloc(dev,
				GTP_CONFIG_MAX_LENGTH + GTP_ADDR_LENGTH,
				GFP_KERNEL);
		if (!pdata->config_data[i]) {
			dev_err(dev,
				"Not enough memory for panel config data %d\n",
				i);
			return -ENOMEM;
		}
		pdata->config_data[i][0] = GTP_REG_CONFIG_DATA >> 8;
		pdata->config_data[i][1] = GTP_REG_CONFIG_DATA & 0xff;
		memcpy(&pdata->config_data[i][GTP_ADDR_LENGTH],
				prop->value, pdata->config_data_len[i]);
		read_cfg_num++;
	}
	dev_dbg(dev, "%d config data read from device tree.\n", read_cfg_num);

	return 0;
}

/*******************************************************
Function:
	I2c probe.
Input:
	client: i2c device struct.
	id: device id.
Output:
	Executive outcomes.
	0: succeed.
*******************************************************/

static int goodix_ts_probe(struct i2c_client *client,
			   const struct i2c_device_id *id)
{
	struct goodix_ts_platform_data *pdata;
	struct goodix_ts_data *ts;
	u16 version_info;
	int ret;

	dev_dbg(&client->dev, "GTP I2C Address: 0x%02x\n", client->addr);
	if (client->dev.of_node) {
		pdata = devm_kzalloc(&client->dev,
			sizeof(struct goodix_ts_platform_data), GFP_KERNEL);
		if (!pdata) {
			dev_err(&client->dev,
				"GTP Failed to allocate memory for pdata\n");
			return -ENOMEM;
		}

		ret = goodix_parse_dt(&client->dev, pdata);
		if (ret)
			return ret;
	} else {
		pdata = client->dev.platform_data;
	}

	if (!pdata) {
		dev_err(&client->dev, "GTP invalid pdata\n");
		return -EINVAL;
	}

#if GTP_ESD_PROTECT
	i2c_connect_client = client;
#endif

	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
		dev_err(&client->dev, "GTP I2C not supported\n");
		return -ENODEV;
	}

	ts = kzalloc(sizeof(*ts), GFP_KERNEL);
	if (!ts) {
		dev_err(&client->dev, "GTP not enough memory for ts\n");
		return -ENOMEM;
	}

	memset(ts, 0, sizeof(*ts));
	ts->client = client;
	ts->pdata = pdata;
	/* For 2.6.39 & later use spin_lock_init(&ts->irq_lock)
	 * For 2.6.39 & before, use ts->irq_lock = SPIN_LOCK_UNLOCKED
	 */
	spin_lock_init(&ts->irq_lock);
	i2c_set_clientdata(client, ts);
	ts->gtp_rawdiff_mode = 0;
	ts->power_on = false;

	ret = gtp_request_io_port(ts);
	if (ret) {
		dev_err(&client->dev, "GTP request IO port failed.\n");
		goto exit_free_client_data;
	}

	ret = goodix_power_init(ts);
	if (ret) {
		dev_err(&client->dev, "GTP power init failed\n");
		goto exit_free_io_port;
	}

	ret = goodix_power_on(ts);
	if (ret) {
		dev_err(&client->dev, "GTP power on failed\n");
		goto exit_deinit_power;
	}

	gtp_reset_guitar(ts, 20);

	ret = gtp_i2c_test(client);
	if (ret != 2) {
		dev_err(&client->dev, "I2C communication ERROR!\n");
		goto exit_power_off;
	}

	if (pdata->fw_name)
		strlcpy(ts->fw_name, pdata->fw_name,
						strlen(pdata->fw_name) + 1);

#if GTP_AUTO_UPDATE
	ret = gup_init_update_proc(ts);
	if (ret < 0) {
		dev_err(&client->dev,
			"GTP Create firmware update thread error.\n");
		goto exit_power_off;
	}
#endif

	ret = gtp_init_panel(ts);
	if (ret < 0) {
		dev_err(&client->dev, "GTP init panel failed.\n");
		ts->abs_x_max = GTP_MAX_WIDTH;
		ts->abs_y_max = GTP_MAX_HEIGHT;
		ts->int_trigger_type = GTP_INT_TRIGGER;
	}

	ret = gtp_request_input_dev(ts);
	if (ret) {
		dev_err(&client->dev, "GTP request input dev failed.\n");
		goto exit_free_inputdev;
	}
	input_set_drvdata(ts->input_dev, ts);

	mutex_init(&ts->lock);
#if defined(CONFIG_FB)
	ts->fb_notif.notifier_call = fb_notifier_callback;
	ret = fb_register_client(&ts->fb_notif);
	if (ret)
		dev_err(&ts->client->dev,
			"Unable to register fb_notifier: %d\n",
			ret);
#elif defined(CONFIG_HAS_EARLYSUSPEND)
	ts->early_suspend.level = EARLY_SUSPEND_LEVEL_BLANK_SCREEN + 1;
	ts->early_suspend.suspend = goodix_ts_early_suspend;
	ts->early_suspend.resume = goodix_ts_late_resume;
	register_early_suspend(&ts->early_suspend);
#endif

	ts->goodix_wq = create_singlethread_workqueue("goodix_wq");
	INIT_WORK(&ts->work, goodix_ts_work_func);

	ret = gtp_request_irq(ts);
	if (ret < 0)
		dev_info(&client->dev, "GTP works in polling mode.\n");
	else
		dev_info(&client->dev, "GTP works in interrupt mode.\n");

	ret = gtp_read_fw_version(client, &version_info);
	if (ret != 0)
		dev_err(&client->dev, "GTP firmware version read failed.\n");

	ret = gtp_check_product_id(client);
	if (ret != 0) {
		dev_err(&client->dev, "GTP Product id doesn't match.\n");
		goto exit_free_irq;
	}
	if (ts->use_irq)
		gtp_irq_enable(ts);

#if GTP_CREATE_WR_NODE
	init_wr_node(client);
#endif

#if GTP_ESD_PROTECT
	gtp_esd_switch(client, SWITCH_ON);
#endif
	ret = sysfs_create_group(&client->dev.kobj, &gtp_attr_grp);
	if (ret < 0) {
		dev_err(&client->dev, "sys file creation failed.\n");
		goto exit_free_irq;
	}

	init_done = true;
	return 0;
exit_free_irq:
	mutex_destroy(&ts->lock);
#if defined(CONFIG_FB)
	if (fb_unregister_client(&ts->fb_notif))
		dev_err(&client->dev,
			"Error occurred while unregistering fb_notifier.\n");
#elif defined(CONFIG_HAS_EARLYSUSPEND)
	unregister_early_suspend(&ts->early_suspend);
#endif
	if (ts->use_irq)
		free_irq(client->irq, ts);
	else
		hrtimer_cancel(&ts->timer);
	cancel_work_sync(&ts->work);
	flush_workqueue(ts->goodix_wq);
	destroy_workqueue(ts->goodix_wq);

	input_unregister_device(ts->input_dev);
	if (ts->input_dev) {
		input_free_device(ts->input_dev);
		ts->input_dev = NULL;
	}
exit_free_inputdev:
	kfree(ts->config_data);
exit_power_off:
	goodix_power_off(ts);
exit_deinit_power:
	goodix_power_deinit(ts);
exit_free_io_port:
	if (gpio_is_valid(pdata->reset_gpio))
		gpio_free(pdata->reset_gpio);
	if (gpio_is_valid(pdata->irq_gpio))
		gpio_free(pdata->irq_gpio);
exit_free_client_data:
	i2c_set_clientdata(client, NULL);
	kfree(ts);
	return ret;
}

/*******************************************************
Function:
	Goodix touchscreen driver release function.
Input:
	client: i2c device struct.
Output:
	Executive outcomes. 0---succeed.
*******************************************************/
static int goodix_ts_remove(struct i2c_client *client)
{
	struct goodix_ts_data *ts = i2c_get_clientdata(client);

	sysfs_remove_group(&ts->input_dev->dev.kobj, &gtp_attr_grp);

#if defined(CONFIG_FB)
	if (fb_unregister_client(&ts->fb_notif))
		dev_err(&client->dev,
			"Error occurred while unregistering fb_notifier.\n");
#elif defined(CONFIG_HAS_EARLYSUSPEND)
	unregister_early_suspend(&ts->early_suspend);
#endif
	mutex_destroy(&ts->lock);

#if GTP_CREATE_WR_NODE
	uninit_wr_node();
#endif

#if GTP_ESD_PROTECT
	cancel_work_sync(gtp_esd_check_workqueue);
	flush_workqueue(gtp_esd_check_workqueue);
	destroy_workqueue(gtp_esd_check_workqueue);
#endif

	if (ts) {
		if (ts->use_irq)
			free_irq(client->irq, ts);
		else
			hrtimer_cancel(&ts->timer);

		cancel_work_sync(&ts->work);
		flush_workqueue(ts->goodix_wq);
		destroy_workqueue(ts->goodix_wq);

		input_unregister_device(ts->input_dev);
		if (ts->input_dev) {
			input_free_device(ts->input_dev);
			ts->input_dev = NULL;
		}
		kfree(ts->config_data);

		if (gpio_is_valid(ts->pdata->reset_gpio))
			gpio_free(ts->pdata->reset_gpio);
		if (gpio_is_valid(ts->pdata->irq_gpio))
			gpio_free(ts->pdata->irq_gpio);

		goodix_power_off(ts);
		goodix_power_deinit(ts);
		i2c_set_clientdata(client, NULL);
		kfree(ts);
	}

	return 0;
}

#if defined(CONFIG_HAS_EARLYSUSPEND) || defined(CONFIG_FB)
/*******************************************************
Function:
	Early suspend function.
Input:
	h: early_suspend struct.
Output:
	None.
*******************************************************/
static int goodix_ts_suspend(struct device *dev)
{
	struct goodix_ts_data *ts = dev_get_drvdata(dev);
	int ret = 0, i;

	mutex_lock(&ts->lock);
#if GTP_ESD_PROTECT
	ts->gtp_is_suspend = 1;
	gtp_esd_switch(ts->client, SWITCH_OFF);
#endif

#if GTP_SLIDE_WAKEUP
	ret = gtp_enter_doze(ts);
#else
	if (ts->use_irq)
		gtp_irq_disable(ts);
	else
		hrtimer_cancel(&ts->timer);

	for (i = 0; i < GTP_MAX_TOUCH; i++)
		gtp_touch_up(ts, i);

	input_sync(ts->input_dev);

	ret = gtp_enter_sleep(ts);
#endif
	if (ret < 0)
		dev_err(&ts->client->dev, "GTP early suspend failed.\n");
	/* to avoid waking up while not sleeping,
	 * delay 48 + 10ms to ensure reliability
	 */
	msleep(58);
	mutex_unlock(&ts->lock);

	return ret;
}

/*******************************************************
Function:
	Late resume function.
Input:
	h: early_suspend struct.
Output:
	None.
*******************************************************/
static int goodix_ts_resume(struct device *dev)
{
	struct goodix_ts_data *ts = dev_get_drvdata(dev);
	int ret = 0;

	mutex_lock(&ts->lock);
	ret = gtp_wakeup_sleep(ts);

#if GTP_SLIDE_WAKEUP
	doze_status = DOZE_DISABLED;
#endif

	if (ret <= 0)
		dev_err(&ts->client->dev, "GTP resume failed.\n");

	if (ts->use_irq)
		gtp_irq_enable(ts);
	else
		hrtimer_start(&ts->timer,
			ktime_set(1, 0), HRTIMER_MODE_REL);

#if GTP_ESD_PROTECT
	ts->gtp_is_suspend = 0;
	gtp_esd_switch(ts->client, SWITCH_ON);
#endif
	mutex_unlock(&ts->lock);

	return ret;
}

#if defined(CONFIG_FB)
static int fb_notifier_callback(struct notifier_block *self,
				 unsigned long event, void *data)
{
	struct fb_event *evdata = data;
	int *blank;
	struct goodix_ts_data *ts =
		container_of(self, struct goodix_ts_data, fb_notif);

	if (evdata && evdata->data && event == FB_EVENT_BLANK &&
			ts && ts->client) {
		blank = evdata->data;
		if (*blank == FB_BLANK_UNBLANK)
			goodix_ts_resume(&ts->client->dev);
		else if (*blank == FB_BLANK_POWERDOWN)
			goodix_ts_suspend(&ts->client->dev);
	}

	return 0;
}
#elif defined(CONFIG_HAS_EARLYSUSPEND)
/*******************************************************
Function:
	Early suspend function.
Input:
	h: early_suspend struct.
Output:
	None.
*******************************************************/
static void goodix_ts_early_suspend(struct early_suspend *h)
{
	struct goodix_ts_data *ts;

	ts = container_of(h, struct goodix_ts_data, early_suspend);
	goodix_ts_suspend(&ts->client->dev);
	return;
}

/*******************************************************
Function:
	Late resume function.
Input:
	h: early_suspend struct.
Output:
	None.
*******************************************************/
static void goodix_ts_late_resume(struct early_suspend *h)
{
	struct goodix_ts_data *ts;

	ts = container_of(h, struct goodix_ts_data, early_suspend);
	goodix_ts_late_resume(ts);
	return;
}
#endif
#endif /* !CONFIG_HAS_EARLYSUSPEND && !CONFIG_FB*/

#if GTP_ESD_PROTECT
/*******************************************************
Function:
	switch on & off esd delayed work
Input:
	client:  i2c device
	on:	SWITCH_ON / SWITCH_OFF
Output:
	void
*********************************************************/
void gtp_esd_switch(struct i2c_client *client, int on)
{
	struct goodix_ts_data *ts;

	ts = i2c_get_clientdata(client);
	if (SWITCH_ON == on) {
		/* switch on esd  */
		if (!ts->esd_running) {
			ts->esd_running = 1;
			dev_dbg(&client->dev, "Esd started\n");
			queue_delayed_work(gtp_esd_check_workqueue,
				&gtp_esd_check_work, GTP_ESD_CHECK_CIRCLE);
		}
	} else {
		/* switch off esd */
		if (ts->esd_running) {
			ts->esd_running = 0;
			dev_dbg(&client->dev, "Esd cancelled\n");
			cancel_delayed_work_sync(&gtp_esd_check_work);
		}
	}
}

/*******************************************************
Function:
	Initialize external watchdog for esd protect
Input:
	client:  i2c device.
Output:
	result of i2c write operation.
		1: succeed, otherwise: failed
*********************************************************/
static int gtp_init_ext_watchdog(struct i2c_client *client)
{
	/* in case of recursively reset by calling gtp_i2c_write*/
	struct i2c_msg msg;
	u8 opr_buffer[4] = {0x80, 0x40, 0xAA, 0xAA};
	int ret;
	int retries = 0;

	msg.flags = !I2C_M_RD;
	msg.addr  = client->addr;
	msg.len   = 4;
	msg.buf   = opr_buffer;

	while (retries < 5) {
		ret = i2c_transfer(client->adapter, &msg, 1);
		if (ret == 1)
			return 1;
		retries++;
	}
	if (retries >= 5)
		dev_err(&client->dev, "init external watchdog failed!");
	return 0;
}

/*******************************************************
Function:
	Esd protect function.
	Added external watchdog by meta, 2013/03/07
Input:
	work: delayed work
Output:
	None.
*******************************************************/
static void gtp_esd_check_func(struct work_struct *work)
{
	s32 i;
	s32 ret = -1;
	struct goodix_ts_data *ts = NULL;
	u8 test[4] = {0x80, 0x40};

	ts = i2c_get_clientdata(i2c_connect_client);

	if (ts->gtp_is_suspend) {
		dev_dbg(&ts->client->dev, "Esd terminated!\n");
		ts->esd_running = 0;
		return;
	}
#ifdef CONFIG_GT9XX_TOUCHPANEL_UPDATE
	if (ts->enter_update)
		return;
#endif

	for (i = 0; i < 3; i++) {
		ret = gtp_i2c_read(ts->client, test, 4);

		if ((ret < 0)) {
			/* IC works abnormally..*/
			continue;
		} else {
			if ((test[2] == 0xAA) || (test[3] != 0xAA)) {
				/* IC works abnormally..*/
				i = 3;
				break;
			} else {
				/* IC works normally, Write 0x8040 0xAA*/
				test[2] = 0xAA;
				gtp_i2c_write(ts->client, test, 3);
				break;
			}
		}
	}
	if (i >= 3) {
		dev_err(&ts->client->dev,
			"IC Working ABNORMALLY, Resetting Guitar...\n");
		gtp_reset_guitar(ts, 50);
	}

	if (!ts->gtp_is_suspend)
		queue_delayed_work(gtp_esd_check_workqueue,
			&gtp_esd_check_work, GTP_ESD_CHECK_CIRCLE);
	else {
		dev_dbg(&ts->client->dev, "Esd terminated!\n");
		ts->esd_running = 0;
	}

	return;
}
#endif

#if (!defined(CONFIG_FB) && !defined(CONFIG_HAS_EARLYSUSPEND))
static const struct dev_pm_ops goodix_ts_dev_pm_ops = {
	.suspend = goodix_ts_suspend,
	.resume = goodix_ts_resume,
};
#else
static const struct dev_pm_ops goodix_ts_dev_pm_ops = {
};
#endif

static const struct i2c_device_id goodix_ts_id[] = {
	{ GTP_I2C_NAME, 0 },
	{ }
};

static struct of_device_id goodix_match_table[] = {
	{ .compatible = "goodix,gt9xx", },
	{ },
};

static struct i2c_driver goodix_ts_driver = {
	.probe      = goodix_ts_probe,
	.remove     = goodix_ts_remove,
#ifdef CONFIG_HAS_EARLYSUSPEND
	.suspend    = goodix_ts_early_suspend,
	.resume     = goodix_ts_late_resume,
#endif
	.id_table   = goodix_ts_id,
	.driver = {
		.name     = GTP_I2C_NAME,
		.owner    = THIS_MODULE,
		.of_match_table = goodix_match_table,
#if CONFIG_PM
		.pm = &goodix_ts_dev_pm_ops,
#endif
	},
};

/*******************************************************
Function:
    Driver Install function.
Input:
    None.
Output:
    Executive Outcomes. 0---succeed.
********************************************************/
static int __devinit goodix_ts_init(void)
{
	int ret;

#if GTP_ESD_PROTECT
	INIT_DELAYED_WORK(&gtp_esd_check_work, gtp_esd_check_func);
	gtp_esd_check_workqueue = create_workqueue("gtp_esd_check");
#endif
	ret = i2c_add_driver(&goodix_ts_driver);
	return ret;
}

/*******************************************************
Function:
	Driver uninstall function.
Input:
	None.
Output:
	Executive Outcomes. 0---succeed.
********************************************************/
static void __exit goodix_ts_exit(void)
{
	i2c_del_driver(&goodix_ts_driver);
}

module_init(goodix_ts_init);
module_exit(goodix_ts_exit);

MODULE_DESCRIPTION("GTP Series Driver");
MODULE_LICENSE("GPL");