diff --git a/drivers/media/dvb/frontends/drxk.h b/drivers/media/dvb/frontends/drxk.h
index 67589b6..a756e45 100644
--- a/drivers/media/dvb/frontends/drxk.h
+++ b/drivers/media/dvb/frontends/drxk.h
@@ -10,18 +10,21 @@
  * adr:			I2C Address of the DRX-K
  * single_master:	Device is on the single master mode
  * no_i2c_bridge:	Don't switch the I2C bridge to talk with tuner
- * antenna_uses_gpio:	Use GPIO to control the antenna
- * antenna_dvbc:	GPIO for changing antenna to DVB-C
- * antenna_dvbt:	GPIO for changing antenna to DVB-T
+ * antenna_gpio:	GPIO bit used to control the antenna
+ * antenna_dvbt:	GPIO bit for changing antenna to DVB-C. A value of 1
+ *			means that 1=DVBC, 0 = DVBT. Zero means the opposite.
  * microcode_name:	Name of the firmware file with the microcode
+ *
+ * On the *_gpio vars, bit 0 is UIO-1, bit 1 is UIO-2 and bit 2 is
+ * UIO-3.
  */
 struct drxk_config {
 	u8	adr;
 	bool	single_master;
 	bool	no_i2c_bridge;
 
-	bool	antenna_uses_gpio;
-	u16	antenna_dvbc, antenna_dvbt;
+	bool	antenna_dvbt;
+	u16	antenna_gpio;
 
 	const char *microcode_name;
 };
diff --git a/drivers/media/dvb/frontends/drxk_hard.c b/drivers/media/dvb/frontends/drxk_hard.c
index 0d288a7..aaef8e3 100644
--- a/drivers/media/dvb/frontends/drxk_hard.c
+++ b/drivers/media/dvb/frontends/drxk_hard.c
@@ -856,7 +856,6 @@
 	state->m_agcFastClipCtrlDelay = 0;
 
 	state->m_GPIOCfg = (ulGPIOCfg);
-	state->m_GPIO = (ulGPIO == 0 ? 0 : 1);
 
 	state->m_bPowerDown = false;
 	state->m_currentPowerMode = DRX_POWER_DOWN;
@@ -5795,24 +5794,63 @@
 		goto error;
 
 	if (state->m_hasSAWSW) {
-		/* write to io pad configuration register - output mode */
-		status = write16(state, SIO_PDR_SMA_TX_CFG__A, state->m_GPIOCfg);
-		if (status < 0)
-			goto error;
+		if (state->UIO_mask & 0x0001) { /* UIO-1 */
+			/* write to io pad configuration register - output mode */
+			status = write16(state, SIO_PDR_SMA_TX_CFG__A, state->m_GPIOCfg);
+			if (status < 0)
+				goto error;
 
-		/* use corresponding bit in io data output registar */
-		status = read16(state, SIO_PDR_UIO_OUT_LO__A, &value);
-		if (status < 0)
-			goto error;
-		if (state->m_GPIO == 0)
-			value &= 0x7FFF;	/* write zero to 15th bit - 1st UIO */
-		else
-			value |= 0x8000;	/* write one to 15th bit - 1st UIO */
-		/* write back to io data output register */
-		status = write16(state, SIO_PDR_UIO_OUT_LO__A, value);
-		if (status < 0)
-			goto error;
+			/* use corresponding bit in io data output registar */
+			status = read16(state, SIO_PDR_UIO_OUT_LO__A, &value);
+			if (status < 0)
+				goto error;
+			if ((state->m_GPIO & 0x0001) == 0)
+				value &= 0x7FFF;	/* write zero to 15th bit - 1st UIO */
+			else
+				value |= 0x8000;	/* write one to 15th bit - 1st UIO */
+			/* write back to io data output register */
+			status = write16(state, SIO_PDR_UIO_OUT_LO__A, value);
+			if (status < 0)
+				goto error;
+		}
+		if (state->UIO_mask & 0x0002) { /* UIO-2 */
+			/* write to io pad configuration register - output mode */
+			status = write16(state, SIO_PDR_SMA_TX_CFG__A, state->m_GPIOCfg);
+			if (status < 0)
+				goto error;
 
+			/* use corresponding bit in io data output registar */
+			status = read16(state, SIO_PDR_UIO_OUT_LO__A, &value);
+			if (status < 0)
+				goto error;
+			if ((state->m_GPIO & 0x0002) == 0)
+				value &= 0xBFFF;	/* write zero to 14th bit - 2st UIO */
+			else
+				value |= 0x4000;	/* write one to 14th bit - 2st UIO */
+			/* write back to io data output register */
+			status = write16(state, SIO_PDR_UIO_OUT_LO__A, value);
+			if (status < 0)
+				goto error;
+		}
+		if (state->UIO_mask & 0x0004) { /* UIO-3 */
+			/* write to io pad configuration register - output mode */
+			status = write16(state, SIO_PDR_SMA_TX_CFG__A, state->m_GPIOCfg);
+			if (status < 0)
+				goto error;
+
+			/* use corresponding bit in io data output registar */
+			status = read16(state, SIO_PDR_UIO_OUT_LO__A, &value);
+			if (status < 0)
+				goto error;
+			if ((state->m_GPIO & 0x0004) == 0)
+				value &= 0xFFFB;            /* write zero to 2nd bit - 3rd UIO */
+			else
+				value |= 0x0004;            /* write one to 2nd bit - 3rd UIO */
+			/* write back to io data output register */
+			status = write16(state, SIO_PDR_UIO_OUT_LO__A, value);
+			if (status < 0)
+				goto error;
+		}
 	}
 	/*  Write magic word to disable pdr reg write               */
 	status = write16(state, SIO_TOP_COMM_KEY__A, 0x0000);
@@ -5825,14 +5863,22 @@
 static int SwitchAntennaToQAM(struct drxk_state *state)
 {
 	int status = 0;
+	bool gpio_state;
 
 	dprintk(1, "\n");
 
-	if (state->m_AntennaSwitchDVBTDVBC != 0) {
-		if (state->m_GPIO != state->m_AntennaDVBC) {
-			state->m_GPIO = state->m_AntennaDVBC;
-			status = WriteGPIO(state);
-		}
+	if (!state->antenna_gpio)
+		return 0;
+
+	gpio_state = state->m_GPIO & state->antenna_gpio;
+
+	if (state->antenna_dvbt ^ gpio_state) {
+		/* Antenna is on DVB-T mode. Switch */
+		if (state->antenna_dvbt)
+			state->m_GPIO &= ~state->antenna_gpio;
+		else
+			state->m_GPIO |= state->antenna_gpio;
+		status = WriteGPIO(state);
 	}
 	if (status < 0)
 		printk(KERN_ERR "drxk: Error %d on %s\n", status, __func__);
@@ -5842,13 +5888,22 @@
 static int SwitchAntennaToDVBT(struct drxk_state *state)
 {
 	int status = 0;
+	bool gpio_state;
 
 	dprintk(1, "\n");
-	if (state->m_AntennaSwitchDVBTDVBC != 0) {
-		if (state->m_GPIO != state->m_AntennaDVBT) {
-			state->m_GPIO = state->m_AntennaDVBT;
-			status = WriteGPIO(state);
-		}
+
+	if (!state->antenna_gpio)
+		return 0;
+
+	gpio_state = state->m_GPIO & state->antenna_gpio;
+
+	if (!(state->antenna_dvbt ^ gpio_state)) {
+		/* Antenna is on DVB-C mode. Switch */
+		if (state->antenna_dvbt)
+			state->m_GPIO |= state->antenna_gpio;
+		else
+			state->m_GPIO &= ~state->antenna_gpio;
+		status = WriteGPIO(state);
 	}
 	if (status < 0)
 		printk(KERN_ERR "drxk: Error %d on %s\n", status, __func__);
@@ -6350,9 +6405,17 @@
 	state->single_master = config->single_master;
 	state->microcode_name = config->microcode_name;
 	state->no_i2c_bridge = config->no_i2c_bridge;
-	state->m_AntennaSwitchDVBTDVBC = config->antenna_uses_gpio;
-	state->m_AntennaDVBC = config->antenna_dvbc;
-	state->m_AntennaDVBT = config->antenna_dvbt;
+	state->antenna_gpio = config->antenna_gpio;
+	state->antenna_dvbt = config->antenna_dvbt;
+
+	/* NOTE: as more UIO bits will be used, add them to the mask */
+	state->UIO_mask = config->antenna_gpio;
+
+	/* Default gpio to DVB-C */
+	if (!state->antenna_dvbt && state->antenna_gpio)
+		state->m_GPIO |= state->antenna_gpio;
+	else
+		state->m_GPIO &= ~state->antenna_gpio;
 
 	mutex_init(&state->mutex);
 	mutex_init(&state->ctlock);
diff --git a/drivers/media/dvb/frontends/drxk_hard.h b/drivers/media/dvb/frontends/drxk_hard.h
index 8b29dc8..a20a19d 100644
--- a/drivers/media/dvb/frontends/drxk_hard.h
+++ b/drivers/media/dvb/frontends/drxk_hard.h
@@ -323,17 +323,19 @@
 
 	enum DRXPowerMode m_currentPowerMode;
 
-	/* Configurable parameters at the driver */
+	/*
+	 * Configurable parameters at the driver. They stores the values found
+	 * at struct drxk_config.
+	 */
 
-	bool              m_AntennaSwitchDVBTDVBC;
-	u16               m_AntennaDVBC;
-	u16               m_AntennaDVBT;
+	u16	UIO_mask;	/* Bits used by UIO */
 
-	u32 single_master : 1;		/* Use single master i2c mode */
-	u32 no_i2c_bridge : 1;		/* Tuner is not on port 1, don't use I2C bridge */
+	bool	single_master;
+	bool	no_i2c_bridge;
+	bool	antenna_dvbt;
+	u16	antenna_gpio;
 
 	const char *microcode_name;
-
 };
 
 #define NEVER_LOCK 0