pcmcia: do not use io_req_t when calling pcmcia_request_io()
Instead of io_req_t, drivers are now requested to fill out
struct pcmcia_device *p_dev->resource[0,1] for up to two ioport
ranges. After a call to pcmcia_request_io(), the ports found there
are reserved, after calling pcmcia_request_configuration(), they may
be used.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
CC: Michael Buesch <mb@bu3sch.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
diff --git a/drivers/net/pcmcia/3c574_cs.c b/drivers/net/pcmcia/3c574_cs.c
index b5ea9b8..c683f77 100644
--- a/drivers/net/pcmcia/3c574_cs.c
+++ b/drivers/net/pcmcia/3c574_cs.c
@@ -278,8 +278,8 @@
lp->p_dev = link;
spin_lock_init(&lp->window_lock);
- link->io.NumPorts1 = 32;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
+ link->resource[0]->end = 32;
+ link->resource[0]->flags |= IO_DATA_PATH_WIDTH_16;
link->conf.Attributes = CONF_ENABLE_IRQ;
link->conf.IntType = INT_MEMORY_AND_IO;
link->conf.ConfigIndex = 1;
@@ -337,10 +337,11 @@
dev_dbg(&link->dev, "3c574_config()\n");
- link->io.IOAddrLines = 16;
+ link->io_lines = 16;
+
for (i = j = 0; j < 0x400; j += 0x20) {
- link->io.BasePort1 = j ^ 0x300;
- i = pcmcia_request_io(link, &link->io);
+ link->resource[0]->start = j ^ 0x300;
+ i = pcmcia_request_io(link);
if (i == 0)
break;
}
diff --git a/drivers/net/pcmcia/3c589_cs.c b/drivers/net/pcmcia/3c589_cs.c
index 122ef4a..61f9cf2 100644
--- a/drivers/net/pcmcia/3c589_cs.c
+++ b/drivers/net/pcmcia/3c589_cs.c
@@ -213,8 +213,8 @@
lp->p_dev = link;
spin_lock_init(&lp->lock);
- link->io.NumPorts1 = 16;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
+ link->resource[0]->end = 16;
+ link->resource[0]->flags |= IO_DATA_PATH_WIDTH_16;
link->conf.Attributes = CONF_ENABLE_IRQ;
link->conf.IntType = INT_MEMORY_AND_IO;
@@ -277,12 +277,13 @@
"3Com card??\n");
multi = (link->card_id == PRODID_3COM_3C562);
+ link->io_lines = 16;
+
/* For the 3c562, the base address must be xx00-xx7f */
- link->io.IOAddrLines = 16;
for (i = j = 0; j < 0x400; j += 0x10) {
if (multi && (j & 0x80)) continue;
- link->io.BasePort1 = j ^ 0x300;
- i = pcmcia_request_io(link, &link->io);
+ link->resource[0]->start = j ^ 0x300;
+ i = pcmcia_request_io(link);
if (i == 0)
break;
}
diff --git a/drivers/net/pcmcia/axnet_cs.c b/drivers/net/pcmcia/axnet_cs.c
index c52fdf3..5f05ffb 100644
--- a/drivers/net/pcmcia/axnet_cs.c
+++ b/drivers/net/pcmcia/axnet_cs.c
@@ -259,28 +259,30 @@
static int try_io_port(struct pcmcia_device *link)
{
int j, ret;
- if (link->io.NumPorts1 == 32) {
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
+ link->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
+ link->resource[1]->flags &= ~IO_DATA_PATH_WIDTH;
+ if (link->resource[0]->end == 32) {
+ link->resource[0]->flags |= IO_DATA_PATH_WIDTH_AUTO;
/* for master/slave multifunction cards */
- if (link->io.NumPorts2 > 0)
- link->io.Attributes2 = IO_DATA_PATH_WIDTH_8;
+ if (link->resource[1]->end > 0)
+ link->resource[1]->flags |= IO_DATA_PATH_WIDTH_8;
} else {
/* This should be two 16-port windows */
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- link->io.Attributes2 = IO_DATA_PATH_WIDTH_16;
+ link->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
+ link->resource[1]->flags |= IO_DATA_PATH_WIDTH_16;
}
- if (link->io.BasePort1 == 0) {
- link->io.IOAddrLines = 16;
+ if (link->resource[0]->start == 0) {
for (j = 0; j < 0x400; j += 0x20) {
- link->io.BasePort1 = j ^ 0x300;
- link->io.BasePort2 = (j ^ 0x300) + 0x10;
- ret = pcmcia_request_io(link, &link->io);
+ link->resource[0]->start = j ^ 0x300;
+ link->resource[1]->start = (j ^ 0x300) + 0x10;
+ link->io_lines = 16;
+ ret = pcmcia_request_io(link);
if (ret == 0)
return ret;
}
return ret;
} else {
- return pcmcia_request_io(link, &link->io);
+ return pcmcia_request_io(link);
}
}
@@ -301,15 +303,15 @@
network function with window 0, and serial with window 1 */
if (io->nwin > 1) {
i = (io->win[1].len > io->win[0].len);
- p_dev->io.BasePort2 = io->win[1-i].base;
- p_dev->io.NumPorts2 = io->win[1-i].len;
+ p_dev->resource[1]->start = io->win[1-i].base;
+ p_dev->resource[1]->end = io->win[1-i].len;
} else {
- i = p_dev->io.NumPorts2 = 0;
+ i = p_dev->resource[1]->end = 0;
}
- p_dev->io.BasePort1 = io->win[i].base;
- p_dev->io.NumPorts1 = io->win[i].len;
- p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
- if (p_dev->io.NumPorts1 + p_dev->io.NumPorts2 >= 32)
+ p_dev->resource[0]->start = io->win[i].base;
+ p_dev->resource[0]->end = io->win[i].len;
+ p_dev->io_lines = io->flags & CISTPL_IO_LINES_MASK;
+ if (p_dev->resource[0]->end + p_dev->resource[1]->end >= 32)
return try_io_port(p_dev);
return -ENODEV;
diff --git a/drivers/net/pcmcia/com20020_cs.c b/drivers/net/pcmcia/com20020_cs.c
index 3b53818..3c400cf 100644
--- a/drivers/net/pcmcia/com20020_cs.c
+++ b/drivers/net/pcmcia/com20020_cs.c
@@ -158,9 +158,8 @@
/* fill in our module parameters as defaults */
dev->dev_addr[0] = node;
- p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- p_dev->io.NumPorts1 = 16;
- p_dev->io.IOAddrLines = 16;
+ p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
+ p_dev->resource[0]->end = 16;
p_dev->conf.Attributes = CONF_ENABLE_IRQ;
p_dev->conf.IntType = INT_MEMORY_AND_IO;
@@ -245,20 +244,24 @@
dev_dbg(&link->dev, "com20020_config\n");
- dev_dbg(&link->dev, "baseport1 is %Xh\n", link->io.BasePort1);
+ dev_dbg(&link->dev, "baseport1 is %Xh\n",
+ (unsigned int) link->resource[0]->start);
+
i = -ENODEV;
- if (!link->io.BasePort1)
+ link->io_lines = 16;
+
+ if (!link->resource[0]->start)
{
for (ioaddr = 0x100; ioaddr < 0x400; ioaddr += 0x10)
{
- link->io.BasePort1 = ioaddr;
- i = pcmcia_request_io(link, &link->io);
+ link->resource[0]->start = ioaddr;
+ i = pcmcia_request_io(link);
if (i == 0)
break;
}
}
else
- i = pcmcia_request_io(link, &link->io);
+ i = pcmcia_request_io(link);
if (i != 0)
{
diff --git a/drivers/net/pcmcia/fmvj18x_cs.c b/drivers/net/pcmcia/fmvj18x_cs.c
index bba6369..6993044 100644
--- a/drivers/net/pcmcia/fmvj18x_cs.c
+++ b/drivers/net/pcmcia/fmvj18x_cs.c
@@ -248,9 +248,8 @@
lp->base = NULL;
/* The io structure describes IO port mapping */
- link->io.NumPorts1 = 32;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- link->io.IOAddrLines = 5;
+ link->resource[0]->end = 32;
+ link->resource[0]->flags |= IO_DATA_PATH_WIDTH_AUTO;
/* General socket configuration */
link->conf.Attributes = CONF_ENABLE_IRQ;
@@ -288,13 +287,13 @@
{ 0x3f8, 0x2f8, 0x3e8, 0x2e8, 0x0 };
for (i = 0; i < 5; i++) {
- link->io.BasePort2 = serial_base[i];
- link->io.Attributes2 = IO_DATA_PATH_WIDTH_8;
- if (link->io.BasePort2 == 0) {
- link->io.NumPorts2 = 0;
+ link->resource[1]->start = serial_base[i];
+ link->resource[1]->flags |= IO_DATA_PATH_WIDTH_8;
+ if (link->resource[1]->start == 0) {
+ link->resource[1]->end = 0;
printk(KERN_NOTICE "fmvj18x_cs: out of resource for serial\n");
}
- ret = pcmcia_request_io(link, &link->io);
+ ret = pcmcia_request_io(link);
if (ret == 0)
return ret;
}
@@ -310,8 +309,8 @@
0x380,0x3c0 only for ioport.
*/
for (ioaddr = 0x300; ioaddr < 0x3e0; ioaddr += 0x20) {
- link->io.BasePort1 = ioaddr;
- ret = pcmcia_request_io(link, &link->io);
+ link->resource[0]->start = ioaddr;
+ ret = pcmcia_request_io(link);
if (ret == 0) {
/* calculate ConfigIndex value */
link->conf.ConfigIndex =
@@ -345,6 +344,8 @@
dev_dbg(&link->dev, "fmvj18x_config\n");
+ link->io_lines = 5;
+
len = pcmcia_get_tuple(link, CISTPL_FUNCE, &buf);
kfree(buf);
@@ -363,20 +364,20 @@
/* MultiFunction Card */
link->conf.ConfigBase = 0x800;
link->conf.ConfigIndex = 0x47;
- link->io.NumPorts2 = 8;
+ link->resource[1]->end = 8;
}
break;
case MANFID_NEC:
cardtype = NEC; /* MultiFunction Card */
link->conf.ConfigBase = 0x800;
link->conf.ConfigIndex = 0x47;
- link->io.NumPorts2 = 8;
+ link->resource[1]->end = 8;
break;
case MANFID_KME:
cardtype = KME; /* MultiFunction Card */
link->conf.ConfigBase = 0x800;
link->conf.ConfigIndex = 0x47;
- link->io.NumPorts2 = 8;
+ link->resource[1]->end = 8;
break;
case MANFID_CONTEC:
cardtype = CONTEC;
@@ -417,14 +418,14 @@
}
}
- if (link->io.NumPorts2 != 0) {
+ if (link->resource[1]->end != 0) {
ret = mfc_try_io_port(link);
if (ret != 0) goto failed;
} else if (cardtype == UNGERMANN) {
ret = ungermann_try_io_port(link);
if (ret != 0) goto failed;
} else {
- ret = pcmcia_request_io(link, &link->io);
+ ret = pcmcia_request_io(link);
if (ret)
goto failed;
}
diff --git a/drivers/net/pcmcia/ibmtr_cs.c b/drivers/net/pcmcia/ibmtr_cs.c
index e99abaa..3fd8595 100644
--- a/drivers/net/pcmcia/ibmtr_cs.c
+++ b/drivers/net/pcmcia/ibmtr_cs.c
@@ -151,9 +151,8 @@
link->priv = info;
info->ti = netdev_priv(dev);
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- link->io.NumPorts1 = 4;
- link->io.IOAddrLines = 16;
+ link->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
+ link->resource[0]->end = 4;
link->conf.Attributes = CONF_ENABLE_IRQ;
link->conf.IntType = INT_MEMORY_AND_IO;
link->conf.Present = PRESENT_OPTION;
@@ -218,16 +217,17 @@
dev_dbg(&link->dev, "ibmtr_config\n");
link->conf.ConfigIndex = 0x61;
+ link->io_lines = 16;
/* Determine if this is PRIMARY or ALTERNATE. */
/* Try PRIMARY card at 0xA20-0xA23 */
- link->io.BasePort1 = 0xA20;
- i = pcmcia_request_io(link, &link->io);
+ link->resource[0]->start = 0xA20;
+ i = pcmcia_request_io(link);
if (i != 0) {
/* Couldn't get 0xA20-0xA23. Try ALTERNATE at 0xA24-0xA27. */
- link->io.BasePort1 = 0xA24;
- ret = pcmcia_request_io(link, &link->io);
+ link->resource[0]->start = 0xA24;
+ ret = pcmcia_request_io(link);
if (ret)
goto failed;
}
diff --git a/drivers/net/pcmcia/nmclan_cs.c b/drivers/net/pcmcia/nmclan_cs.c
index 9980cbb..68f2dee 100644
--- a/drivers/net/pcmcia/nmclan_cs.c
+++ b/drivers/net/pcmcia/nmclan_cs.c
@@ -458,9 +458,8 @@
link->priv = dev;
spin_lock_init(&lp->bank_lock);
- link->io.NumPorts1 = 32;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- link->io.IOAddrLines = 5;
+ link->resource[0]->end = 32;
+ link->resource[0]->flags |= IO_DATA_PATH_WIDTH_AUTO;
link->conf.Attributes = CONF_ENABLE_IRQ;
link->conf.IntType = INT_MEMORY_AND_IO;
link->conf.ConfigIndex = 1;
@@ -644,7 +643,8 @@
dev_dbg(&link->dev, "nmclan_config\n");
- ret = pcmcia_request_io(link, &link->io);
+ link->io_lines = 5;
+ ret = pcmcia_request_io(link);
if (ret)
goto failed;
ret = pcmcia_request_exclusive_irq(link, mace_interrupt);
diff --git a/drivers/net/pcmcia/pcnet_cs.c b/drivers/net/pcmcia/pcnet_cs.c
index c9cd237..9c5fc9d 100644
--- a/drivers/net/pcmcia/pcnet_cs.c
+++ b/drivers/net/pcmcia/pcnet_cs.c
@@ -477,29 +477,31 @@
static int try_io_port(struct pcmcia_device *link)
{
int j, ret;
- if (link->io.NumPorts1 == 32) {
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- if (link->io.NumPorts2 > 0) {
+ link->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
+ link->resource[1]->flags &= ~IO_DATA_PATH_WIDTH;
+ if (link->resource[0]->end == 32) {
+ link->resource[0]->flags |= IO_DATA_PATH_WIDTH_AUTO;
+ if (link->resource[1]->end > 0) {
/* for master/slave multifunction cards */
- link->io.Attributes2 = IO_DATA_PATH_WIDTH_8;
+ link->resource[1]->flags |= IO_DATA_PATH_WIDTH_8;
}
} else {
/* This should be two 16-port windows */
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- link->io.Attributes2 = IO_DATA_PATH_WIDTH_16;
+ link->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
+ link->resource[1]->flags |= IO_DATA_PATH_WIDTH_16;
}
- if (link->io.BasePort1 == 0) {
- link->io.IOAddrLines = 16;
+ if (link->resource[0]->start == 0) {
for (j = 0; j < 0x400; j += 0x20) {
- link->io.BasePort1 = j ^ 0x300;
- link->io.BasePort2 = (j ^ 0x300) + 0x10;
- ret = pcmcia_request_io(link, &link->io);
+ link->resource[0]->start = j ^ 0x300;
+ link->resource[1]->start = (j ^ 0x300) + 0x10;
+ link->io_lines = 16;
+ ret = pcmcia_request_io(link);
if (ret == 0)
return ret;
}
return ret;
} else {
- return pcmcia_request_io(link, &link->io);
+ return pcmcia_request_io(link);
}
}
@@ -520,18 +522,18 @@
network function with window 0, and serial with window 1 */
if (io->nwin > 1) {
i = (io->win[1].len > io->win[0].len);
- p_dev->io.BasePort2 = io->win[1-i].base;
- p_dev->io.NumPorts2 = io->win[1-i].len;
+ p_dev->resource[1]->start = io->win[1-i].base;
+ p_dev->resource[1]->end = io->win[1-i].len;
} else {
- i = p_dev->io.NumPorts2 = 0;
+ i = p_dev->resource[1]->end = 0;
}
*has_shmem = ((cfg->mem.nwin == 1) &&
(cfg->mem.win[0].len >= 0x4000));
- p_dev->io.BasePort1 = io->win[i].base;
- p_dev->io.NumPorts1 = io->win[i].len;
- p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
- if (p_dev->io.NumPorts1 + p_dev->io.NumPorts2 >= 32)
+ p_dev->resource[0]->start = io->win[i].base;
+ p_dev->resource[0]->end = io->win[i].len;
+ p_dev->io_lines = io->flags & CISTPL_IO_LINES_MASK;
+ if (p_dev->resource[0]->end + p_dev->resource[1]->end >= 32)
return try_io_port(p_dev);
return 0;
diff --git a/drivers/net/pcmcia/smc91c92_cs.c b/drivers/net/pcmcia/smc91c92_cs.c
index 1b0b3230..a5e4779 100644
--- a/drivers/net/pcmcia/smc91c92_cs.c
+++ b/drivers/net/pcmcia/smc91c92_cs.c
@@ -324,9 +324,8 @@
link->priv = dev;
spin_lock_init(&smc->lock);
- link->io.NumPorts1 = 16;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- link->io.IOAddrLines = 4;
+ link->resource[0]->end = 16;
+ link->resource[0]->flags |= IO_DATA_PATH_WIDTH_AUTO;
link->conf.Attributes = CONF_ENABLE_IRQ;
link->conf.IntType = INT_MEMORY_AND_IO;
@@ -427,12 +426,13 @@
void *priv_data)
{
int k;
- p_dev->io.BasePort2 = cf->io.win[0].base;
+ p_dev->resource[1]->start = cf->io.win[0].base;
for (k = 0; k < 0x400; k += 0x10) {
if (k & 0x80)
continue;
- p_dev->io.BasePort1 = k ^ 0x300;
- if (!pcmcia_request_io(p_dev, &p_dev->io))
+ p_dev->resource[0]->start = k ^ 0x300;
+ p_dev->io_lines = 16;
+ if (!pcmcia_request_io(p_dev))
return 0;
}
return -ENODEV;
@@ -448,9 +448,8 @@
link->conf.Attributes |= CONF_ENABLE_SPKR;
link->conf.Status = CCSR_AUDIO_ENA;
- link->io.IOAddrLines = 16;
- link->io.Attributes2 = IO_DATA_PATH_WIDTH_8;
- link->io.NumPorts2 = 8;
+ link->resource[1]->flags |= IO_DATA_PATH_WIDTH_8;
+ link->resource[1]->end = 8;
/* The Megahertz combo cards have modem-like CIS entries, so
we have to explicitly try a bunch of port combinations. */
@@ -601,9 +600,9 @@
unsigned int vcc,
void *priv_data)
{
- p_dev->io.BasePort1 = cf->io.win[0].base;
- p_dev->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK;
- return pcmcia_request_io(p_dev, &p_dev->io);
+ p_dev->resource[0]->start = cf->io.win[0].base;
+ p_dev->io_lines = cf->io.flags & CISTPL_IO_LINES_MASK;
+ return pcmcia_request_io(p_dev);
}
static int smc_config(struct pcmcia_device *link)
@@ -611,7 +610,7 @@
struct net_device *dev = link->priv;
int i;
- link->io.NumPorts1 = 16;
+ link->resource[0]->end = 16;
i = pcmcia_loop_config(link, smc_configcheck, NULL);
if (!i)
dev->base_addr = link->resource[0]->start;
@@ -646,25 +645,25 @@
link->conf.Attributes |= CONF_ENABLE_SPKR;
link->conf.Status = CCSR_AUDIO_ENA;
- link->io.NumPorts1 = 64;
- link->io.Attributes2 = IO_DATA_PATH_WIDTH_8;
- link->io.NumPorts2 = 8;
- link->io.IOAddrLines = 16;
+ link->resource[0]->end = 64;
+ link->resource[1]->flags |= IO_DATA_PATH_WIDTH_8;
+ link->resource[1]->end = 8;
/* Enable Hard Decode, LAN, Modem */
link->conf.ConfigIndex = 0x23;
+ link->io_lines = 16;
for (i = j = 0; j < 4; j++) {
- link->io.BasePort2 = com[j];
- i = pcmcia_request_io(link, &link->io);
+ link->resource[1]->start = com[j];
+ i = pcmcia_request_io(link);
if (i == 0)
break;
}
if (i != 0) {
/* Fallback: turn off hard decode */
link->conf.ConfigIndex = 0x03;
- link->io.NumPorts2 = 0;
- i = pcmcia_request_io(link, &link->io);
+ link->resource[1]->end = 0;
+ i = pcmcia_request_io(link);
}
dev->base_addr = link->resource[0]->start + 0x10;
return i;
@@ -803,7 +802,7 @@
}
/* Try setting bus width */
- width = (link->io.Attributes1 == IO_DATA_PATH_WIDTH_AUTO);
+ width = (link->resource[0]->flags == IO_DATA_PATH_WIDTH_AUTO);
s = inb(ioaddr + CONFIG);
if (width)
s |= CFG_16BIT;
diff --git a/drivers/net/pcmcia/xirc2ps_cs.c b/drivers/net/pcmcia/xirc2ps_cs.c
index 034920b..8fb0eb1 100644
--- a/drivers/net/pcmcia/xirc2ps_cs.c
+++ b/drivers/net/pcmcia/xirc2ps_cs.c
@@ -677,9 +677,9 @@
if (cf->io.nwin > 0 && (cf->io.win[0].base & 0xf) == 8) {
for (ioaddr = 0x300; ioaddr < 0x400; ioaddr += 0x10) {
- p_dev->io.BasePort2 = cf->io.win[0].base;
- p_dev->io.BasePort1 = ioaddr;
- if (!pcmcia_request_io(p_dev, &p_dev->io))
+ p_dev->resource[1]->start = cf->io.win[0].base;
+ p_dev->resource[0]->start = ioaddr;
+ if (!pcmcia_request_io(p_dev))
return 0;
}
}
@@ -696,11 +696,11 @@
int *pass = priv_data;
if (cf->io.nwin > 0 && (cf->io.win[0].base & 0xf) == 8) {
- p_dev->io.BasePort2 = cf->io.win[0].base;
- p_dev->io.BasePort1 = p_dev->io.BasePort2
+ p_dev->resource[1]->start = cf->io.win[0].base;
+ p_dev->resource[0]->start = p_dev->resource[1]->start
+ (*pass ? (cf->index & 0x20 ? -24:8)
: (cf->index & 0x20 ? 8:-24));
- if (!pcmcia_request_io(p_dev, &p_dev->io))
+ if (!pcmcia_request_io(p_dev))
return 0;
}
return -ENODEV;
@@ -807,8 +807,7 @@
goto failure;
}
- link->io.IOAddrLines =10;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
+ link->resource[0]->flags |= IO_DATA_PATH_WIDTH_16;
if (local->modem) {
int pass;
@@ -816,16 +815,16 @@
link->conf.Attributes |= CONF_ENABLE_SPKR;
link->conf.Status |= CCSR_AUDIO_ENA;
}
- link->io.NumPorts2 = 8;
- link->io.Attributes2 = IO_DATA_PATH_WIDTH_8;
+ link->resource[1]->end = 8;
+ link->resource[1]->flags |= IO_DATA_PATH_WIDTH_8;
if (local->dingo) {
/* Take the Modem IO port from the CIS and scan for a free
* Ethernet port */
- link->io.NumPorts1 = 16; /* no Mako stuff anymore */
+ link->resource[0]->end = 16; /* no Mako stuff anymore */
if (!pcmcia_loop_config(link, xirc2ps_config_modem, NULL))
goto port_found;
} else {
- link->io.NumPorts1 = 18;
+ link->resource[0]->end = 18;
/* We do 2 passes here: The first one uses the regular mapping and
* the second tries again, thereby considering that the 32 ports are
* mirrored every 32 bytes. Actually we use a mirrored port for
@@ -840,14 +839,15 @@
}
printk(KNOT_XIRC "no ports available\n");
} else {
- link->io.NumPorts1 = 16;
+ link->io_lines = 10;
+ link->resource[0]->end = 16;
for (ioaddr = 0x300; ioaddr < 0x400; ioaddr += 0x10) {
- link->io.BasePort1 = ioaddr;
- if (!(err=pcmcia_request_io(link, &link->io)))
+ link->resource[0]->start = ioaddr;
+ if (!(err = pcmcia_request_io(link)))
goto port_found;
}
- link->io.BasePort1 = 0; /* let CS decide */
- if ((err=pcmcia_request_io(link, &link->io)))
+ link->resource[0]->start = 0; /* let CS decide */
+ if ((err = pcmcia_request_io(link)))
goto config_error;
}
port_found: