arch/arm/mach-msm/platsmp.c

/*
 *  Copyright (C) 2002 ARM Ltd.
 *  All Rights Reserved
 *  Copyright (c) 2010, Code Aurora Forum. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */

#include <linux/init.h>
#include <linux/errno.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/jiffies.h>
#include <linux/smp.h>
#include <linux/io.h>

#include <asm/hardware/gic.h>
#include <asm/cacheflush.h>
#include <asm/mach-types.h>

#include <mach/msm_iomap.h>

#include "scm-boot.h"

#define VDD_SC1_ARRAY_CLAMP_GFS_CTL 0x15A0
#define SCSS_CPU1CORE_RESET 0xD80
#define SCSS_DBG_STATUS_CORE_PWRDUP 0xE64

/* Mask for edge trigger PPIs except AVS_SVICINT and AVS_SVICINTSWDONE */
#define GIC_PPI_EDGE_MASK 0xFFFFD7FF

extern void msm_secondary_startup(void);
/*
 * control for which core is the next to come out of the secondary
 * boot "holding pen".
 */
volatile int pen_release = -1;

static DEFINE_SPINLOCK(boot_lock);

void __cpuinit platform_secondary_init(unsigned int cpu)
{
	/* Configure edge-triggered PPIs */
	writel(GIC_PPI_EDGE_MASK, MSM_QGIC_DIST_BASE + GIC_DIST_CONFIG + 4);

	/*
	 * if any interrupts are already enabled for the primary
	 * core (e.g. timer irq), then they will not have been enabled
	 * for us: do so
	 */
	gic_secondary_init(0);

	/*
	 * let the primary processor know we're out of the
	 * pen, then head off into the C entry point
	 */
	pen_release = -1;
	smp_wmb();

	/*
	 * Synchronise with the boot thread.
	 */
	spin_lock(&boot_lock);
	spin_unlock(&boot_lock);
}

static __cpuinit void prepare_cold_cpu(unsigned int cpu)
{
	int ret;
	ret = scm_set_boot_addr(virt_to_phys(msm_secondary_startup),
				SCM_FLAG_COLDBOOT_CPU1);
	if (ret == 0) {
		void *sc1_base_ptr;
		sc1_base_ptr = ioremap_nocache(0x00902000, SZ_4K*2);
		if (sc1_base_ptr) {
			writel(0, sc1_base_ptr + VDD_SC1_ARRAY_CLAMP_GFS_CTL);
			writel(0, sc1_base_ptr + SCSS_CPU1CORE_RESET);
			writel(3, sc1_base_ptr + SCSS_DBG_STATUS_CORE_PWRDUP);
			iounmap(sc1_base_ptr);
		}
	} else
		printk(KERN_DEBUG "Failed to set secondary core boot "
				  "address\n");
}

int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
{
	unsigned long timeout;
	static int cold_boot_done;

	/* Only need to bring cpu out of reset this way once */
	if (cold_boot_done == false) {
		prepare_cold_cpu(cpu);
		cold_boot_done = true;
	}

	/*
	 * set synchronisation state between this boot processor
	 * and the secondary one
	 */
	spin_lock(&boot_lock);

	/*
	 * The secondary processor is waiting to be released from
	 * the holding pen - release it, then wait for it to flag
	 * that it has been released by resetting pen_release.
	 *
	 * Note that "pen_release" is the hardware CPU ID, whereas
	 * "cpu" is Linux's internal ID.
	 */
	pen_release = cpu;
	__cpuc_flush_dcache_area((void *)&pen_release, sizeof(pen_release));
	outer_clean_range(__pa(&pen_release), __pa(&pen_release + 1));

	/*
	 * Send the secondary CPU a soft interrupt, thereby causing
	 * the boot monitor to read the system wide flags register,
	 * and branch to the address found there.
	 */
	gic_raise_softirq(cpumask_of(cpu), 1);

	timeout = jiffies + (1 * HZ);
	while (time_before(jiffies, timeout)) {
		smp_rmb();
		if (pen_release == -1)
			break;

		udelay(10);
	}

	/*
	 * now the secondary core is starting up let it run its
	 * calibrations, then wait for it to finish
	 */
	spin_unlock(&boot_lock);

	return pen_release != -1 ? -ENOSYS : 0;
}

/*
 * Initialise the CPU possible map early - this describes the CPUs
 * which may be present or become present in the system. The msm8x60
 * does not support the ARM SCU, so just set the possible cpu mask to
 * NR_CPUS.
 */
void __init smp_init_cpus(void)
{
	unsigned int i;

	for (i = 0; i < NR_CPUS; i++)
		set_cpu_possible(i, true);

        set_smp_cross_call(gic_raise_softirq);
}

void __init platform_smp_prepare_cpus(unsigned int max_cpus)
{
	int i;

	/*
	 * Initialise the present map, which describes the set of CPUs
	 * actually populated at the present time.
	 */
	for (i = 0; i < max_cpus; i++)
		set_cpu_present(i, true);
}