mac80211: be more careful in suspend/resume
When suspending with all netdevs down, the device
is stopped but we still call a number of driver
callbacks that the driver might not expect. The
same happens during resume, we might call a few
callbacks without starting the driver. Fix this
by checking open_count around more things and
exiting quickly if it is 0.
Also, while at this I noticed that the coverage
class isn't reprogrammed after resume, so add
that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/net/mac80211/pm.c b/net/mac80211/pm.c
index f87e993..6326d34 100644
--- a/net/mac80211/pm.c
+++ b/net/mac80211/pm.c
@@ -34,6 +34,9 @@
struct ieee80211_sub_if_data *sdata;
struct sta_info *sta;
+ if (!local->open_count)
+ goto suspend;
+
ieee80211_scan_cancel(local);
if (hw->flags & IEEE80211_HW_AMPDU_AGGREGATION) {
diff --git a/net/mac80211/util.c b/net/mac80211/util.c
index 5bfb80c..8c2df33 100644
--- a/net/mac80211/util.c
+++ b/net/mac80211/util.c
@@ -1157,27 +1157,37 @@
}
#endif
- /* restart hardware */
- if (local->open_count) {
- /*
- * Upon resume hardware can sometimes be goofy due to
- * various platform / driver / bus issues, so restarting
- * the device may at times not work immediately. Propagate
- * the error.
- */
- res = drv_start(local);
- if (res) {
- WARN(local->suspended, "Hardware became unavailable "
- "upon resume. This could be a software issue "
- "prior to suspend or a hardware issue.\n");
- return res;
- }
+ /* setup fragmentation threshold */
+ drv_set_frag_threshold(local, hw->wiphy->frag_threshold);
- ieee80211_led_radio(local, true);
- ieee80211_mod_tpt_led_trig(local,
- IEEE80211_TPT_LEDTRIG_FL_RADIO, 0);
+ /* setup RTS threshold */
+ drv_set_rts_threshold(local, hw->wiphy->rts_threshold);
+
+ /* reset coverage class */
+ drv_set_coverage_class(local, hw->wiphy->coverage_class);
+
+ /* everything else happens only if HW was up & running */
+ if (!local->open_count)
+ goto wake_up;
+
+ /*
+ * Upon resume hardware can sometimes be goofy due to
+ * various platform / driver / bus issues, so restarting
+ * the device may at times not work immediately. Propagate
+ * the error.
+ */
+ res = drv_start(local);
+ if (res) {
+ WARN(local->suspended, "Hardware became unavailable "
+ "upon resume. This could be a software issue "
+ "prior to suspend or a hardware issue.\n");
+ return res;
}
+ ieee80211_led_radio(local, true);
+ ieee80211_mod_tpt_led_trig(local,
+ IEEE80211_TPT_LEDTRIG_FL_RADIO, 0);
+
/* add interfaces */
list_for_each_entry(sdata, &local->interfaces, list) {
if (sdata->vif.type != NL80211_IFTYPE_AP_VLAN &&
@@ -1201,12 +1211,6 @@
}
mutex_unlock(&local->sta_mtx);
- /* setup fragmentation threshold */
- drv_set_frag_threshold(local, hw->wiphy->frag_threshold);
-
- /* setup RTS threshold */
- drv_set_rts_threshold(local, hw->wiphy->rts_threshold);
-
/* reconfigure hardware */
ieee80211_hw_config(local, ~0);
@@ -1287,9 +1291,7 @@
if (ieee80211_sdata_running(sdata))
ieee80211_enable_keys(sdata);
-#ifdef CONFIG_PM
wake_up:
-#endif
ieee80211_wake_queues_by_reason(hw,
IEEE80211_QUEUE_STOP_REASON_SUSPEND);