MMC headers learn about SPI
Teach the MMC/SD/SDIO system headers that some hosts use SPI mode
- New host capabilities and status bits
* MMC_CAP_SPI, with mmc_host_is_spi() test
* mmc_host.use_spi_crc flag
- SPI-specific declarations:
* Response types, MMC_RSP_SPI_R*
* Two SPI-only commands
* Status bits used native to SPI: R1_SPI_*, R2_SPI_*
- Fix a few (unrelated) whitespace bugs in the headers.
- Reorder a few mmc_host fields, removing several bytes of padding
None of these changes affect current code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
diff --git a/include/linux/mmc/mmc.h b/include/linux/mmc/mmc.h
index d1d6cbc..4236fbf 100644
--- a/include/linux/mmc/mmc.h
+++ b/include/linux/mmc/mmc.h
@@ -27,7 +27,7 @@
/* Standard MMC commands (4.1) type argument response */
/* class 1 */
-#define MMC_GO_IDLE_STATE 0 /* bc */
+#define MMC_GO_IDLE_STATE 0 /* bc */
#define MMC_SEND_OP_COND 1 /* bcr [31:0] OCR R3 */
#define MMC_ALL_SEND_CID 2 /* bcr R2 */
#define MMC_SET_RELATIVE_ADDR 3 /* ac [31:16] RCA R1 */
@@ -39,8 +39,10 @@
#define MMC_SEND_CID 10 /* ac [31:16] RCA R2 */
#define MMC_READ_DAT_UNTIL_STOP 11 /* adtc [31:0] dadr R1 */
#define MMC_STOP_TRANSMISSION 12 /* ac R1b */
-#define MMC_SEND_STATUS 13 /* ac [31:16] RCA R1 */
+#define MMC_SEND_STATUS 13 /* ac [31:16] RCA R1 */
#define MMC_GO_INACTIVE_STATE 15 /* ac [31:16] RCA */
+#define MMC_SPI_READ_OCR 58 /* spi spi_R3 */
+#define MMC_SPI_CRC_ON_OFF 59 /* spi [0:0] flag spi_R1 */
/* class 2 */
#define MMC_SET_BLOCKLEN 16 /* ac [31:0] block len R1 */
@@ -90,15 +92,15 @@
*/
/*
- MMC status in R1
+ MMC status in R1, for native mode (SPI bits are different)
Type
- e : error bit
+ e : error bit
s : status bit
r : detected and set for the actual command response
x : detected and set during command execution. the host must poll
the card by sending status command in order to read these bits.
Clear condition
- a : according to the card state
+ a : according to the card state
b : always related to the previous command. Reception of
a valid command will clear it (with a delay of one command)
c : clear by read
@@ -124,10 +126,33 @@
#define R1_CARD_ECC_DISABLED (1 << 14) /* sx, a */
#define R1_ERASE_RESET (1 << 13) /* sr, c */
#define R1_STATUS(x) (x & 0xFFFFE000)
-#define R1_CURRENT_STATE(x) ((x & 0x00001E00) >> 9) /* sx, b (4 bits) */
+#define R1_CURRENT_STATE(x) ((x & 0x00001E00) >> 9) /* sx, b (4 bits) */
#define R1_READY_FOR_DATA (1 << 8) /* sx, a */
#define R1_APP_CMD (1 << 5) /* sr, c */
+/*
+ * MMC/SD in SPI mode reports R1 status always, and R2 for SEND_STATUS
+ * R1 is the low order byte; R2 is the next highest byte, when present.
+ */
+#define R1_SPI_IDLE (1 << 0)
+#define R1_SPI_ERASE_RESET (1 << 1)
+#define R1_SPI_ILLEGAL_COMMAND (1 << 2)
+#define R1_SPI_COM_CRC (1 << 3)
+#define R1_SPI_ERASE_SEQ (1 << 4)
+#define R1_SPI_ADDRESS (1 << 5)
+#define R1_SPI_PARAMETER (1 << 6)
+/* R1 bit 7 is always zero */
+#define R2_SPI_CARD_LOCKED (1 << 8)
+#define R2_SPI_WP_ERASE_SKIP (1 << 9) /* or lock/unlock fail */
+#define R2_SPI_LOCK_UNLOCK_FAIL R2_SPI_WP_ERASE_SKIP
+#define R2_SPI_ERROR (1 << 10)
+#define R2_SPI_CC_ERROR (1 << 11)
+#define R2_SPI_CARD_ECC_ERROR (1 << 12)
+#define R2_SPI_WP_VIOLATION (1 << 13)
+#define R2_SPI_ERASE_PARAM (1 << 14)
+#define R2_SPI_OUT_OF_RANGE (1 << 15) /* or CSD overwrite */
+#define R2_SPI_CSD_OVERWRITE R2_SPI_OUT_OF_RANGE
+
/* These are unpacked versions of the actual responses */
struct _mmc_csd {
@@ -182,6 +207,7 @@
*/
#define CCC_BASIC (1<<0) /* (0) Basic protocol functions */
/* (CMD0,1,2,3,4,7,9,10,12,13,15) */
+ /* (and for SPI, CMD58,59) */
#define CCC_STREAM_READ (1<<1) /* (1) Stream read commands */
/* (CMD11) */
#define CCC_BLOCK_READ (1<<2) /* (2) Block read commands */