i2c: Bus drivers return -Errno not -1
Tighten error paths used by various i2c adapters (mostly x86) so
they return real fault/errno codes instead of a "-1" (which is
most often interpreted as "-EPERM"). Build tested, with eyeball
review.
One minor initial goal is to have adapters consistently return
the code "-ENXIO" when addressing a device doesn't get an ACK
response, at least in the probe paths where they are already
good at stifling related logspam.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
diff --git a/drivers/i2c/busses/i2c-ali1535.c b/drivers/i2c/busses/i2c-ali1535.c
index f14372a..c21e4d9 100644
--- a/drivers/i2c/busses/i2c-ali1535.c
+++ b/drivers/i2c/busses/i2c-ali1535.c
@@ -259,7 +259,7 @@
dev_err(&adap->dev,
"SMBus reset failed! (0x%02x) - controller or "
"device on bus is probably hung\n", temp);
- return -1;
+ return -EBUSY;
}
} else {
/* check and clear done bit */
@@ -281,12 +281,12 @@
/* If the SMBus is still busy, we give up */
if (timeout >= MAX_TIMEOUT) {
- result = -1;
+ result = -ETIMEDOUT;
dev_err(&adap->dev, "SMBus Timeout!\n");
}
if (temp & ALI1535_STS_FAIL) {
- result = -1;
+ result = -EIO;
dev_dbg(&adap->dev, "Error: Failed bus transaction\n");
}
@@ -295,7 +295,7 @@
* do a printk. This means that bus collisions go unreported.
*/
if (temp & ALI1535_STS_BUSERR) {
- result = -1;
+ result = -ENXIO;
dev_dbg(&adap->dev,
"Error: no response or bus collision ADD=%02x\n",
inb_p(SMBHSTADD));
@@ -303,13 +303,13 @@
/* haven't ever seen this */
if (temp & ALI1535_STS_DEV) {
- result = -1;
+ result = -EIO;
dev_err(&adap->dev, "Error: device error\n");
}
/* check to see if the "command complete" indication is set */
if (!(temp & ALI1535_STS_DONE)) {
- result = -1;
+ result = -ETIMEDOUT;
dev_err(&adap->dev, "Error: command never completed\n");
}
@@ -332,7 +332,7 @@
return result;
}
-/* Return -1 on error. */
+/* Return negative errno on error. */
static s32 ali1535_access(struct i2c_adapter *adap, u16 addr,
unsigned short flags, char read_write, u8 command,
int size, union i2c_smbus_data *data)
@@ -359,7 +359,7 @@
switch (size) {
case I2C_SMBUS_PROC_CALL:
dev_err(&adap->dev, "I2C_SMBUS_PROC_CALL not supported!\n");
- result = -1;
+ result = -EOPNOTSUPP;
goto EXIT;
case I2C_SMBUS_QUICK:
outb_p(((addr & 0x7f) << 1) | (read_write & 0x01),
@@ -420,11 +420,9 @@
break;
}
- if (ali1535_transaction(adap)) {
- /* Error in transaction */
- result = -1;
+ result = ali1535_transaction(adap);
+ if (result)
goto EXIT;
- }
if ((read_write == I2C_SMBUS_WRITE) || (size == ALI1535_QUICK)) {
result = 0;