| #ifndef LINUX_BCMA_DRIVER_CC_H_ |
| #define LINUX_BCMA_DRIVER_CC_H_ |
| |
| /** ChipCommon core registers. **/ |
| #define BCMA_CC_ID 0x0000 |
| #define BCMA_CC_ID_ID 0x0000FFFF |
| #define BCMA_CC_ID_ID_SHIFT 0 |
| #define BCMA_CC_ID_REV 0x000F0000 |
| #define BCMA_CC_ID_REV_SHIFT 16 |
| #define BCMA_CC_ID_PKG 0x00F00000 |
| #define BCMA_CC_ID_PKG_SHIFT 20 |
| #define BCMA_CC_ID_NRCORES 0x0F000000 |
| #define BCMA_CC_ID_NRCORES_SHIFT 24 |
| #define BCMA_CC_ID_TYPE 0xF0000000 |
| #define BCMA_CC_ID_TYPE_SHIFT 28 |
| #define BCMA_CC_CAP 0x0004 /* Capabilities */ |
| #define BCMA_CC_CAP_NRUART 0x00000003 /* # of UARTs */ |
| #define BCMA_CC_CAP_MIPSEB 0x00000004 /* MIPS in BigEndian Mode */ |
| #define BCMA_CC_CAP_UARTCLK 0x00000018 /* UART clock select */ |
| #define BCMA_CC_CAP_UARTCLK_INT 0x00000008 /* UARTs are driven by internal divided clock */ |
| #define BCMA_CC_CAP_UARTGPIO 0x00000020 /* UARTs on GPIO 15-12 */ |
| #define BCMA_CC_CAP_EXTBUS 0x000000C0 /* External buses present */ |
| #define BCMA_CC_CAP_FLASHT 0x00000700 /* Flash Type */ |
| #define BCMA_CC_FLASHT_NONE 0x00000000 /* No flash */ |
| #define BCMA_CC_FLASHT_STSER 0x00000100 /* ST serial flash */ |
| #define BCMA_CC_FLASHT_ATSER 0x00000200 /* Atmel serial flash */ |
| #define BCMA_CC_FLASHT_NFLASH 0x00000200 |
| #define BCMA_CC_FLASHT_PARA 0x00000700 /* Parallel flash */ |
| #define BCMA_CC_CAP_PLLT 0x00038000 /* PLL Type */ |
| #define BCMA_PLLTYPE_NONE 0x00000000 |
| #define BCMA_PLLTYPE_1 0x00010000 /* 48Mhz base, 3 dividers */ |
| #define BCMA_PLLTYPE_2 0x00020000 /* 48Mhz, 4 dividers */ |
| #define BCMA_PLLTYPE_3 0x00030000 /* 25Mhz, 2 dividers */ |
| #define BCMA_PLLTYPE_4 0x00008000 /* 48Mhz, 4 dividers */ |
| #define BCMA_PLLTYPE_5 0x00018000 /* 25Mhz, 4 dividers */ |
| #define BCMA_PLLTYPE_6 0x00028000 /* 100/200 or 120/240 only */ |
| #define BCMA_PLLTYPE_7 0x00038000 /* 25Mhz, 4 dividers */ |
| #define BCMA_CC_CAP_PCTL 0x00040000 /* Power Control */ |
| #define BCMA_CC_CAP_OTPS 0x00380000 /* OTP size */ |
| #define BCMA_CC_CAP_OTPS_SHIFT 19 |
| #define BCMA_CC_CAP_OTPS_BASE 5 |
| #define BCMA_CC_CAP_JTAGM 0x00400000 /* JTAG master present */ |
| #define BCMA_CC_CAP_BROM 0x00800000 /* Internal boot ROM active */ |
| #define BCMA_CC_CAP_64BIT 0x08000000 /* 64-bit Backplane */ |
| #define BCMA_CC_CAP_PMU 0x10000000 /* PMU available (rev >= 20) */ |
| #define BCMA_CC_CAP_ECI 0x20000000 /* ECI available (rev >= 20) */ |
| #define BCMA_CC_CAP_SPROM 0x40000000 /* SPROM present */ |
| #define BCMA_CC_CORECTL 0x0008 |
| #define BCMA_CC_CORECTL_UARTCLK0 0x00000001 /* Drive UART with internal clock */ |
| #define BCMA_CC_CORECTL_SE 0x00000002 /* sync clk out enable (corerev >= 3) */ |
| #define BCMA_CC_CORECTL_UARTCLKEN 0x00000008 /* UART clock enable (rev >= 21) */ |
| #define BCMA_CC_BIST 0x000C |
| #define BCMA_CC_OTPS 0x0010 /* OTP status */ |
| #define BCMA_CC_OTPS_PROGFAIL 0x80000000 |
| #define BCMA_CC_OTPS_PROTECT 0x00000007 |
| #define BCMA_CC_OTPS_HW_PROTECT 0x00000001 |
| #define BCMA_CC_OTPS_SW_PROTECT 0x00000002 |
| #define BCMA_CC_OTPS_CID_PROTECT 0x00000004 |
| #define BCMA_CC_OTPC 0x0014 /* OTP control */ |
| #define BCMA_CC_OTPC_RECWAIT 0xFF000000 |
| #define BCMA_CC_OTPC_PROGWAIT 0x00FFFF00 |
| #define BCMA_CC_OTPC_PRW_SHIFT 8 |
| #define BCMA_CC_OTPC_MAXFAIL 0x00000038 |
| #define BCMA_CC_OTPC_VSEL 0x00000006 |
| #define BCMA_CC_OTPC_SELVL 0x00000001 |
| #define BCMA_CC_OTPP 0x0018 /* OTP prog */ |
| #define BCMA_CC_OTPP_COL 0x000000FF |
| #define BCMA_CC_OTPP_ROW 0x0000FF00 |
| #define BCMA_CC_OTPP_ROW_SHIFT 8 |
| #define BCMA_CC_OTPP_READERR 0x10000000 |
| #define BCMA_CC_OTPP_VALUE 0x20000000 |
| #define BCMA_CC_OTPP_READ 0x40000000 |
| #define BCMA_CC_OTPP_START 0x80000000 |
| #define BCMA_CC_OTPP_BUSY 0x80000000 |
| #define BCMA_CC_IRQSTAT 0x0020 |
| #define BCMA_CC_IRQMASK 0x0024 |
| #define BCMA_CC_IRQ_GPIO 0x00000001 /* gpio intr */ |
| #define BCMA_CC_IRQ_EXT 0x00000002 /* ro: ext intr pin (corerev >= 3) */ |
| #define BCMA_CC_IRQ_WDRESET 0x80000000 /* watchdog reset occurred */ |
| #define BCMA_CC_CHIPCTL 0x0028 /* Rev >= 11 only */ |
| #define BCMA_CC_CHIPSTAT 0x002C /* Rev >= 11 only */ |
| #define BCMA_CC_JCMD 0x0030 /* Rev >= 10 only */ |
| #define BCMA_CC_JCMD_START 0x80000000 |
| #define BCMA_CC_JCMD_BUSY 0x80000000 |
| #define BCMA_CC_JCMD_PAUSE 0x40000000 |
| #define BCMA_CC_JCMD0_ACC_MASK 0x0000F000 |
| #define BCMA_CC_JCMD0_ACC_IRDR 0x00000000 |
| #define BCMA_CC_JCMD0_ACC_DR 0x00001000 |
| #define BCMA_CC_JCMD0_ACC_IR 0x00002000 |
| #define BCMA_CC_JCMD0_ACC_RESET 0x00003000 |
| #define BCMA_CC_JCMD0_ACC_IRPDR 0x00004000 |
| #define BCMA_CC_JCMD0_ACC_PDR 0x00005000 |
| #define BCMA_CC_JCMD0_IRW_MASK 0x00000F00 |
| #define BCMA_CC_JCMD_ACC_MASK 0x000F0000 /* Changes for corerev 11 */ |
| #define BCMA_CC_JCMD_ACC_IRDR 0x00000000 |
| #define BCMA_CC_JCMD_ACC_DR 0x00010000 |
| #define BCMA_CC_JCMD_ACC_IR 0x00020000 |
| #define BCMA_CC_JCMD_ACC_RESET 0x00030000 |
| #define BCMA_CC_JCMD_ACC_IRPDR 0x00040000 |
| #define BCMA_CC_JCMD_ACC_PDR 0x00050000 |
| #define BCMA_CC_JCMD_IRW_MASK 0x00001F00 |
| #define BCMA_CC_JCMD_IRW_SHIFT 8 |
| #define BCMA_CC_JCMD_DRW_MASK 0x0000003F |
| #define BCMA_CC_JIR 0x0034 /* Rev >= 10 only */ |
| #define BCMA_CC_JDR 0x0038 /* Rev >= 10 only */ |
| #define BCMA_CC_JCTL 0x003C /* Rev >= 10 only */ |
| #define BCMA_CC_JCTL_FORCE_CLK 4 /* Force clock */ |
| #define BCMA_CC_JCTL_EXT_EN 2 /* Enable external targets */ |
| #define BCMA_CC_JCTL_EN 1 /* Enable Jtag master */ |
| #define BCMA_CC_FLASHCTL 0x0040 |
| #define BCMA_CC_FLASHCTL_START 0x80000000 |
| #define BCMA_CC_FLASHCTL_BUSY BCMA_CC_FLASHCTL_START |
| #define BCMA_CC_FLASHADDR 0x0044 |
| #define BCMA_CC_FLASHDATA 0x0048 |
| #define BCMA_CC_BCAST_ADDR 0x0050 |
| #define BCMA_CC_BCAST_DATA 0x0054 |
| #define BCMA_CC_GPIOPULLUP 0x0058 /* Rev >= 20 only */ |
| #define BCMA_CC_GPIOPULLDOWN 0x005C /* Rev >= 20 only */ |
| #define BCMA_CC_GPIOIN 0x0060 |
| #define BCMA_CC_GPIOOUT 0x0064 |
| #define BCMA_CC_GPIOOUTEN 0x0068 |
| #define BCMA_CC_GPIOCTL 0x006C |
| #define BCMA_CC_GPIOPOL 0x0070 |
| #define BCMA_CC_GPIOIRQ 0x0074 |
| #define BCMA_CC_WATCHDOG 0x0080 |
| #define BCMA_CC_GPIOTIMER 0x0088 /* LED powersave (corerev >= 16) */ |
| #define BCMA_CC_GPIOTIMER_OFFTIME 0x0000FFFF |
| #define BCMA_CC_GPIOTIMER_OFFTIME_SHIFT 0 |
| #define BCMA_CC_GPIOTIMER_ONTIME 0xFFFF0000 |
| #define BCMA_CC_GPIOTIMER_ONTIME_SHIFT 16 |
| #define BCMA_CC_GPIOTOUTM 0x008C /* LED powersave (corerev >= 16) */ |
| #define BCMA_CC_CLOCK_N 0x0090 |
| #define BCMA_CC_CLOCK_SB 0x0094 |
| #define BCMA_CC_CLOCK_PCI 0x0098 |
| #define BCMA_CC_CLOCK_M2 0x009C |
| #define BCMA_CC_CLOCK_MIPS 0x00A0 |
| #define BCMA_CC_CLKDIV 0x00A4 /* Rev >= 3 only */ |
| #define BCMA_CC_CLKDIV_SFLASH 0x0F000000 |
| #define BCMA_CC_CLKDIV_SFLASH_SHIFT 24 |
| #define BCMA_CC_CLKDIV_OTP 0x000F0000 |
| #define BCMA_CC_CLKDIV_OTP_SHIFT 16 |
| #define BCMA_CC_CLKDIV_JTAG 0x00000F00 |
| #define BCMA_CC_CLKDIV_JTAG_SHIFT 8 |
| #define BCMA_CC_CLKDIV_UART 0x000000FF |
| #define BCMA_CC_CAP_EXT 0x00AC /* Capabilities */ |
| #define BCMA_CC_PLLONDELAY 0x00B0 /* Rev >= 4 only */ |
| #define BCMA_CC_FREFSELDELAY 0x00B4 /* Rev >= 4 only */ |
| #define BCMA_CC_SLOWCLKCTL 0x00B8 /* 6 <= Rev <= 9 only */ |
| #define BCMA_CC_SLOWCLKCTL_SRC 0x00000007 /* slow clock source mask */ |
| #define BCMA_CC_SLOWCLKCTL_SRC_LPO 0x00000000 /* source of slow clock is LPO */ |
| #define BCMA_CC_SLOWCLKCTL_SRC_XTAL 0x00000001 /* source of slow clock is crystal */ |
| #define BCMA_CC_SLOECLKCTL_SRC_PCI 0x00000002 /* source of slow clock is PCI */ |
| #define BCMA_CC_SLOWCLKCTL_LPOFREQ 0x00000200 /* LPOFreqSel, 1: 160Khz, 0: 32KHz */ |
| #define BCMA_CC_SLOWCLKCTL_LPOPD 0x00000400 /* LPOPowerDown, 1: LPO is disabled, 0: LPO is enabled */ |
| #define BCMA_CC_SLOWCLKCTL_FSLOW 0x00000800 /* ForceSlowClk, 1: sb/cores running on slow clock, 0: power logic control */ |
| #define BCMA_CC_SLOWCLKCTL_IPLL 0x00001000 /* IgnorePllOffReq, 1/0: power logic ignores/honors PLL clock disable requests from core */ |
| #define BCMA_CC_SLOWCLKCTL_ENXTAL 0x00002000 /* XtalControlEn, 1/0: power logic does/doesn't disable crystal when appropriate */ |
| #define BCMA_CC_SLOWCLKCTL_XTALPU 0x00004000 /* XtalPU (RO), 1/0: crystal running/disabled */ |
| #define BCMA_CC_SLOWCLKCTL_CLKDIV 0xFFFF0000 /* ClockDivider (SlowClk = 1/(4+divisor)) */ |
| #define BCMA_CC_SLOWCLKCTL_CLKDIV_SHIFT 16 |
| #define BCMA_CC_SYSCLKCTL 0x00C0 /* Rev >= 3 only */ |
| #define BCMA_CC_SYSCLKCTL_IDLPEN 0x00000001 /* ILPen: Enable Idle Low Power */ |
| #define BCMA_CC_SYSCLKCTL_ALPEN 0x00000002 /* ALPen: Enable Active Low Power */ |
| #define BCMA_CC_SYSCLKCTL_PLLEN 0x00000004 /* ForcePLLOn */ |
| #define BCMA_CC_SYSCLKCTL_FORCEALP 0x00000008 /* Force ALP (or HT if ALPen is not set */ |
| #define BCMA_CC_SYSCLKCTL_FORCEHT 0x00000010 /* Force HT */ |
| #define BCMA_CC_SYSCLKCTL_CLKDIV 0xFFFF0000 /* ClkDiv (ILP = 1/(4+divisor)) */ |
| #define BCMA_CC_SYSCLKCTL_CLKDIV_SHIFT 16 |
| #define BCMA_CC_CLKSTSTR 0x00C4 /* Rev >= 3 only */ |
| #define BCMA_CC_EROM 0x00FC |
| #define BCMA_CC_PCMCIA_CFG 0x0100 |
| #define BCMA_CC_PCMCIA_MEMWAIT 0x0104 |
| #define BCMA_CC_PCMCIA_ATTRWAIT 0x0108 |
| #define BCMA_CC_PCMCIA_IOWAIT 0x010C |
| #define BCMA_CC_IDE_CFG 0x0110 |
| #define BCMA_CC_IDE_MEMWAIT 0x0114 |
| #define BCMA_CC_IDE_ATTRWAIT 0x0118 |
| #define BCMA_CC_IDE_IOWAIT 0x011C |
| #define BCMA_CC_PROG_CFG 0x0120 |
| #define BCMA_CC_PROG_WAITCNT 0x0124 |
| #define BCMA_CC_FLASH_CFG 0x0128 |
| #define BCMA_CC_FLASH_CFG_DS 0x0010 /* Data size, 0=8bit, 1=16bit */ |
| #define BCMA_CC_FLASH_WAITCNT 0x012C |
| /* 0x1E0 is defined as shared BCMA_CLKCTLST */ |
| #define BCMA_CC_HW_WORKAROUND 0x01E4 /* Hardware workaround (rev >= 20) */ |
| #define BCMA_CC_UART0_DATA 0x0300 |
| #define BCMA_CC_UART0_IMR 0x0304 |
| #define BCMA_CC_UART0_FCR 0x0308 |
| #define BCMA_CC_UART0_LCR 0x030C |
| #define BCMA_CC_UART0_MCR 0x0310 |
| #define BCMA_CC_UART0_LSR 0x0314 |
| #define BCMA_CC_UART0_MSR 0x0318 |
| #define BCMA_CC_UART0_SCRATCH 0x031C |
| #define BCMA_CC_UART1_DATA 0x0400 |
| #define BCMA_CC_UART1_IMR 0x0404 |
| #define BCMA_CC_UART1_FCR 0x0408 |
| #define BCMA_CC_UART1_LCR 0x040C |
| #define BCMA_CC_UART1_MCR 0x0410 |
| #define BCMA_CC_UART1_LSR 0x0414 |
| #define BCMA_CC_UART1_MSR 0x0418 |
| #define BCMA_CC_UART1_SCRATCH 0x041C |
| /* PMU registers (rev >= 20) */ |
| #define BCMA_CC_PMU_CTL 0x0600 /* PMU control */ |
| #define BCMA_CC_PMU_CTL_ILP_DIV 0xFFFF0000 /* ILP div mask */ |
| #define BCMA_CC_PMU_CTL_ILP_DIV_SHIFT 16 |
| #define BCMA_CC_PMU_CTL_NOILPONW 0x00000200 /* No ILP on wait */ |
| #define BCMA_CC_PMU_CTL_HTREQEN 0x00000100 /* HT req enable */ |
| #define BCMA_CC_PMU_CTL_ALPREQEN 0x00000080 /* ALP req enable */ |
| #define BCMA_CC_PMU_CTL_XTALFREQ 0x0000007C /* Crystal freq */ |
| #define BCMA_CC_PMU_CTL_XTALFREQ_SHIFT 2 |
| #define BCMA_CC_PMU_CTL_ILPDIVEN 0x00000002 /* ILP div enable */ |
| #define BCMA_CC_PMU_CTL_LPOSEL 0x00000001 /* LPO sel */ |
| #define BCMA_CC_PMU_CAP 0x0604 /* PMU capabilities */ |
| #define BCMA_CC_PMU_CAP_REVISION 0x000000FF /* Revision mask */ |
| #define BCMA_CC_PMU_STAT 0x0608 /* PMU status */ |
| #define BCMA_CC_PMU_STAT_INTPEND 0x00000040 /* Interrupt pending */ |
| #define BCMA_CC_PMU_STAT_SBCLKST 0x00000030 /* Backplane clock status? */ |
| #define BCMA_CC_PMU_STAT_HAVEALP 0x00000008 /* ALP available */ |
| #define BCMA_CC_PMU_STAT_HAVEHT 0x00000004 /* HT available */ |
| #define BCMA_CC_PMU_STAT_RESINIT 0x00000003 /* Res init */ |
| #define BCMA_CC_PMU_RES_STAT 0x060C /* PMU res status */ |
| #define BCMA_CC_PMU_RES_PEND 0x0610 /* PMU res pending */ |
| #define BCMA_CC_PMU_TIMER 0x0614 /* PMU timer */ |
| #define BCMA_CC_PMU_MINRES_MSK 0x0618 /* PMU min res mask */ |
| #define BCMA_CC_PMU_MAXRES_MSK 0x061C /* PMU max res mask */ |
| #define BCMA_CC_PMU_RES_TABSEL 0x0620 /* PMU res table sel */ |
| #define BCMA_CC_PMU_RES_DEPMSK 0x0624 /* PMU res dep mask */ |
| #define BCMA_CC_PMU_RES_UPDNTM 0x0628 /* PMU res updown timer */ |
| #define BCMA_CC_PMU_RES_TIMER 0x062C /* PMU res timer */ |
| #define BCMA_CC_PMU_CLKSTRETCH 0x0630 /* PMU clockstretch */ |
| #define BCMA_CC_PMU_WATCHDOG 0x0634 /* PMU watchdog */ |
| #define BCMA_CC_PMU_RES_REQTS 0x0640 /* PMU res req timer sel */ |
| #define BCMA_CC_PMU_RES_REQT 0x0644 /* PMU res req timer */ |
| #define BCMA_CC_PMU_RES_REQM 0x0648 /* PMU res req mask */ |
| #define BCMA_CC_CHIPCTL_ADDR 0x0650 |
| #define BCMA_CC_CHIPCTL_DATA 0x0654 |
| #define BCMA_CC_REGCTL_ADDR 0x0658 |
| #define BCMA_CC_REGCTL_DATA 0x065C |
| #define BCMA_CC_PLLCTL_ADDR 0x0660 |
| #define BCMA_CC_PLLCTL_DATA 0x0664 |
| #define BCMA_CC_SPROM 0x0800 /* SPROM beginning */ |
| #define BCMA_CC_SPROM_PCIE6 0x0830 /* SPROM beginning on PCIe rev >= 6 */ |
| |
| /* Divider allocation in 4716/47162/5356 */ |
| #define BCMA_CC_PMU5_MAINPLL_CPU 1 |
| #define BCMA_CC_PMU5_MAINPLL_MEM 2 |
| #define BCMA_CC_PMU5_MAINPLL_SSB 3 |
| |
| /* PLL usage in 4716/47162 */ |
| #define BCMA_CC_PMU4716_MAINPLL_PLL0 12 |
| |
| /* PLL usage in 5356/5357 */ |
| #define BCMA_CC_PMU5356_MAINPLL_PLL0 0 |
| #define BCMA_CC_PMU5357_MAINPLL_PLL0 0 |
| |
| /* 4706 PMU */ |
| #define BCMA_CC_PMU4706_MAINPLL_PLL0 0 |
| |
| /* ALP clock on pre-PMU chips */ |
| #define BCMA_CC_PMU_ALP_CLOCK 20000000 |
| /* HT clock for systems with PMU-enabled chipcommon */ |
| #define BCMA_CC_PMU_HT_CLOCK 80000000 |
| |
| /* PMU rev 5 (& 6) */ |
| #define BCMA_CC_PPL_P1P2_OFF 0 |
| #define BCMA_CC_PPL_P1_MASK 0x0f000000 |
| #define BCMA_CC_PPL_P1_SHIFT 24 |
| #define BCMA_CC_PPL_P2_MASK 0x00f00000 |
| #define BCMA_CC_PPL_P2_SHIFT 20 |
| #define BCMA_CC_PPL_M14_OFF 1 |
| #define BCMA_CC_PPL_MDIV_MASK 0x000000ff |
| #define BCMA_CC_PPL_MDIV_WIDTH 8 |
| #define BCMA_CC_PPL_NM5_OFF 2 |
| #define BCMA_CC_PPL_NDIV_MASK 0xfff00000 |
| #define BCMA_CC_PPL_NDIV_SHIFT 20 |
| #define BCMA_CC_PPL_FMAB_OFF 3 |
| #define BCMA_CC_PPL_MRAT_MASK 0xf0000000 |
| #define BCMA_CC_PPL_MRAT_SHIFT 28 |
| #define BCMA_CC_PPL_ABRAT_MASK 0x08000000 |
| #define BCMA_CC_PPL_ABRAT_SHIFT 27 |
| #define BCMA_CC_PPL_FDIV_MASK 0x07ffffff |
| #define BCMA_CC_PPL_PLLCTL_OFF 4 |
| #define BCMA_CC_PPL_PCHI_OFF 5 |
| #define BCMA_CC_PPL_PCHI_MASK 0x0000003f |
| |
| /* BCM4331 ChipControl numbers. */ |
| #define BCMA_CHIPCTL_4331_BT_COEXIST BIT(0) /* 0 disable */ |
| #define BCMA_CHIPCTL_4331_SECI BIT(1) /* 0 SECI is disabled (JATG functional) */ |
| #define BCMA_CHIPCTL_4331_EXT_LNA BIT(2) /* 0 disable */ |
| #define BCMA_CHIPCTL_4331_SPROM_GPIO13_15 BIT(3) /* sprom/gpio13-15 mux */ |
| #define BCMA_CHIPCTL_4331_EXTPA_EN BIT(4) /* 0 ext pa disable, 1 ext pa enabled */ |
| #define BCMA_CHIPCTL_4331_GPIOCLK_ON_SPROMCS BIT(5) /* set drive out GPIO_CLK on sprom_cs pin */ |
| #define BCMA_CHIPCTL_4331_PCIE_MDIO_ON_SPROMCS BIT(6) /* use sprom_cs pin as PCIE mdio interface */ |
| #define BCMA_CHIPCTL_4331_EXTPA_ON_GPIO2_5 BIT(7) /* aband extpa will be at gpio2/5 and sprom_dout */ |
| #define BCMA_CHIPCTL_4331_OVR_PIPEAUXCLKEN BIT(8) /* override core control on pipe_AuxClkEnable */ |
| #define BCMA_CHIPCTL_4331_OVR_PIPEAUXPWRDOWN BIT(9) /* override core control on pipe_AuxPowerDown */ |
| #define BCMA_CHIPCTL_4331_PCIE_AUXCLKEN BIT(10) /* pcie_auxclkenable */ |
| #define BCMA_CHIPCTL_4331_PCIE_PIPE_PLLDOWN BIT(11) /* pcie_pipe_pllpowerdown */ |
| #define BCMA_CHIPCTL_4331_BT_SHD0_ON_GPIO4 BIT(16) /* enable bt_shd0 at gpio4 */ |
| #define BCMA_CHIPCTL_4331_BT_SHD1_ON_GPIO5 BIT(17) /* enable bt_shd1 at gpio5 */ |
| |
| /* Data for the PMU, if available. |
| * Check availability with ((struct bcma_chipcommon)->capabilities & BCMA_CC_CAP_PMU) |
| */ |
| struct bcma_chipcommon_pmu { |
| u8 rev; /* PMU revision */ |
| u32 crystalfreq; /* The active crystal frequency (in kHz) */ |
| }; |
| |
| #ifdef CONFIG_BCMA_DRIVER_MIPS |
| struct bcma_pflash { |
| u8 buswidth; |
| u32 window; |
| u32 window_size; |
| }; |
| |
| struct bcma_serial_port { |
| void *regs; |
| unsigned long clockspeed; |
| unsigned int irq; |
| unsigned int baud_base; |
| unsigned int reg_shift; |
| }; |
| #endif /* CONFIG_BCMA_DRIVER_MIPS */ |
| |
| struct bcma_drv_cc { |
| struct bcma_device *core; |
| u32 status; |
| u32 capabilities; |
| u32 capabilities_ext; |
| u8 setup_done:1; |
| /* Fast Powerup Delay constant */ |
| u16 fast_pwrup_delay; |
| struct bcma_chipcommon_pmu pmu; |
| #ifdef CONFIG_BCMA_DRIVER_MIPS |
| struct bcma_pflash pflash; |
| |
| int nr_serial_ports; |
| struct bcma_serial_port serial_ports[4]; |
| #endif /* CONFIG_BCMA_DRIVER_MIPS */ |
| }; |
| |
| /* Register access */ |
| #define bcma_cc_read32(cc, offset) \ |
| bcma_read32((cc)->core, offset) |
| #define bcma_cc_write32(cc, offset, val) \ |
| bcma_write32((cc)->core, offset, val) |
| |
| #define bcma_cc_mask32(cc, offset, mask) \ |
| bcma_cc_write32(cc, offset, bcma_cc_read32(cc, offset) & (mask)) |
| #define bcma_cc_set32(cc, offset, set) \ |
| bcma_cc_write32(cc, offset, bcma_cc_read32(cc, offset) | (set)) |
| #define bcma_cc_maskset32(cc, offset, mask, set) \ |
| bcma_cc_write32(cc, offset, (bcma_cc_read32(cc, offset) & (mask)) | (set)) |
| |
| extern void bcma_core_chipcommon_init(struct bcma_drv_cc *cc); |
| |
| extern void bcma_chipco_suspend(struct bcma_drv_cc *cc); |
| extern void bcma_chipco_resume(struct bcma_drv_cc *cc); |
| |
| void bcma_chipco_bcm4331_ext_pa_lines_ctl(struct bcma_drv_cc *cc, bool enable); |
| |
| extern void bcma_chipco_watchdog_timer_set(struct bcma_drv_cc *cc, |
| u32 ticks); |
| |
| void bcma_chipco_irq_mask(struct bcma_drv_cc *cc, u32 mask, u32 value); |
| |
| u32 bcma_chipco_irq_status(struct bcma_drv_cc *cc, u32 mask); |
| |
| /* Chipcommon GPIO pin access. */ |
| u32 bcma_chipco_gpio_in(struct bcma_drv_cc *cc, u32 mask); |
| u32 bcma_chipco_gpio_out(struct bcma_drv_cc *cc, u32 mask, u32 value); |
| u32 bcma_chipco_gpio_outen(struct bcma_drv_cc *cc, u32 mask, u32 value); |
| u32 bcma_chipco_gpio_control(struct bcma_drv_cc *cc, u32 mask, u32 value); |
| u32 bcma_chipco_gpio_intmask(struct bcma_drv_cc *cc, u32 mask, u32 value); |
| u32 bcma_chipco_gpio_polarity(struct bcma_drv_cc *cc, u32 mask, u32 value); |
| |
| /* PMU support */ |
| extern void bcma_pmu_init(struct bcma_drv_cc *cc); |
| |
| #endif /* LINUX_BCMA_DRIVER_CC_H_ */ |