| /* |
| * Copyright (c) 2013, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| &i2c { |
| |
| led_flash0: qcom,led-flash@60 { |
| cell-index = <0>; |
| reg = <0x60>; |
| qcom,slave-id = <0x60 0x00 0x0011>; |
| compatible = "qcom,led-flash"; |
| qcom,flash-name = "adp1600"; |
| qcom,flash-type = <1>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 18 0>, |
| <&msmgpio 19 0>; |
| qcom,gpio-flash-en = <0>; |
| qcom,gpio-flash-now = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <0 0>; |
| qcom,gpio-req-tbl-label = "FLASH_EN", |
| "FLASH_NOW"; |
| }; |
| |
| actuator0: qcom,actuator@6e { |
| cell-index = <3>; |
| reg = <0x6c>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <0>; |
| }; |
| |
| eeprom0: qcom,eeprom@6a { |
| cell-index = <0>; |
| reg = <0x6a 0x0>; |
| qcom,eeprom-name = "truly_cm7700"; |
| compatible = "qcom,msm_eeprom"; |
| qcom,slave-addr = <0x6c>; |
| qcom,num-blocks = <9>; |
| qcom,page0 = <1 0x0100 2 0x01 1 1>; |
| qcom,poll0 = <0 0x0 2 0 1 1>; |
| qcom,mem0 = <0 0x0 2 0 1 0>; |
| qcom,page1 = <1 0x3d84 2 0x8 1 1>; |
| qcom,pageen1 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll1 = <0 0x0 2 0 1 1>; |
| qcom,mem1 = <32 0x3d00 2 0 1 0>; |
| qcom,page2 = <1 0x3d84 2 0x9 1 1>; |
| qcom,pageen2 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll2 = <0 0x0 2 0 1 1>; |
| qcom,mem2 = <32 0x3d00 2 0 1 0>; |
| qcom,page3 = <1 0x3d84 2 0xa 1 1>; |
| qcom,pageen3 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll3 = <0 0x0 2 0 1 1>; |
| qcom,mem3 = <32 0x3d00 2 0 1 0>; |
| qcom,page4 = <1 0x3d84 2 0xb 1 1>; |
| qcom,pageen4 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll4 = <0 0x0 2 0 1 1>; |
| qcom,mem4 = <32 0x3d00 2 0 1 0>; |
| qcom,page5 = <1 0x3d84 2 0xc 1 1>; |
| qcom,pageen5 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll5 = <0 0x0 2 0 1 1>; |
| qcom,mem5 = <32 0x3d00 2 0 1 0>; |
| qcom,page6 = <1 0x3d84 2 0xd 1 1>; |
| qcom,pageen6 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll6 = <0 0x0 2 0 1 1>; |
| qcom,mem6 = <32 0x3d00 2 0 1 0>; |
| qcom,page7 = <1 0x3d84 2 0xe 1 1>; |
| qcom,pageen7 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll7 = <0 0x0 2 0 1 1>; |
| qcom,mem7 = <32 0x3d00 2 0 1 0>; |
| qcom,page8 = <1 0x3d84 2 0xf 1 1>; |
| qcom,pageen8 = <1 0x3d81 2 0x01 1 10>; |
| qcom,poll8 = <0 0x0 2 0 1 1>; |
| qcom,mem8 = <32 0x3d00 2 0 1 0>; |
| |
| cam_vdig-supply = <&pm8110_l2>; |
| cam_vio-supply = <&pm8110_l14>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio"; |
| qcom,cam-vreg-type = <0 0 0 0>; |
| qcom,cam-vreg-min-voltage = <1200000 1800000>; |
| qcom,cam-vreg-max-voltage = <1200000 1800000>; |
| qcom,cam-vreg-op-mode = <200000 8000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 13 0>, |
| <&msmgpio 21 0>, |
| <&msmgpio 20 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY"; |
| qcom,cam-power-seq-type = "sensor_vreg", |
| "sensor_vreg", "sensor_clk", |
| "sensor_gpio", "sensor_gpio"; |
| qcom,cam-power-seq-val = "cam_vdig", |
| "cam_vio", "sensor_cam_mclk", |
| "sensor_gpio_reset", |
| "sensor_gpio_standby"; |
| qcom,cam-power-seq-cfg-val = <1 1 24000000 1 1>; |
| qcom,cam-power-seq-delay = <1 1 5 5 10>; |
| }; |
| |
| qcom,camera@6f { |
| compatible = "qcom,ov8825"; |
| reg = <0x6f>; |
| qcom,slave-id = <0x6c 0x300a 0x8825>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,actuator-src = <&actuator0>; |
| qcom,led-flash-src = <&led_flash0>; |
| qcom,eeprom-src = <&eeprom0>; |
| qcom,mount-angle = <90>; |
| qcom,sensor-name = "ov8825"; |
| cam_vdig-supply = <&pm8110_l2>; |
| cam_vana-supply = <&pm8110_l19>; |
| cam_vio-supply = <&pm8110_l14>; |
| cam_vaf-supply = <&pm8110_l16>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| "cam_vaf"; |
| qcom,cam-vreg-type = <0 0 0 0>; |
| qcom,cam-vreg-min-voltage = <1200000 1800000 2850000 3000000>; |
| qcom,cam-vreg-max-voltage = <1200000 1800000 2850000 3000000>; |
| qcom,cam-vreg-op-mode = <200000 8000 80000 100000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 13 0>, |
| <&msmgpio 21 0>, |
| <&msmgpio 20 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET1", |
| "CAM_STANDBY"; |
| qcom,csi-lane-assign = <0xe4>; |
| qcom,csi-lane-mask = <0x3>; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <0>; |
| }; |
| |
| qcom,camera@6d { |
| compatible = "qcom,ov9724"; |
| reg = <0x6d>; |
| qcom,slave-id = <0x20 0x0 0x9724>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <0>; |
| qcom,mount-angle = <90>; |
| qcom,sensor-name = "ov9724"; |
| cam_vdig-supply = <&pm8110_l4>; |
| cam_vana-supply = <&pm8110_l19>; |
| cam_vio-supply = <&pm8110_l14>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <0 1 0>; |
| qcom,cam-vreg-min-voltage = <1200000 0 2850000>; |
| qcom,cam-vreg-max-voltage = <1200000 0 2850000>; |
| qcom,cam-vreg-op-mode = <200000 0 80000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 14 0>, |
| <&msmgpio 15 0>, |
| <&msmgpio 8 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET", |
| "CAM_STANDBY"; |
| qcom,gpio-set-tbl-num = <1 1>; |
| qcom,gpio-set-tbl-flags = <0 2>; |
| qcom,gpio-set-tbl-delay = <1000 4000>; |
| qcom,csi-lane-assign = <0xe4>; |
| qcom,csi-lane-mask = <0x1>; |
| qcom,sensor-position = <1>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| }; |
| |
| qcom,camera@78 { |
| compatible = "qcom,sp1628"; |
| reg = <0x78>; |
| qcom,slave-id = <0x78 0x0 0x1628>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <1>; |
| qcom,mount-angle = <90>; |
| qcom,sensor-name = "sp1628"; |
| cam_vdig-supply = <&pm8110_l2>; |
| cam_vana-supply = <&pm8110_l19>; |
| cam_vio-supply = <&pm8110_l14>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <0 0 0>; |
| qcom,cam-vreg-min-voltage = <1200000 1800000 2850000>; |
| qcom,cam-vreg-max-voltage = <1200000 1800000 2850000>; |
| qcom,cam-vreg-op-mode = <200000 80000 80000>; |
| qcom,gpio-no-mux = <0>; |
| gpios = <&msmgpio 14 0>, |
| <&msmgpio 15 0>, |
| <&msmgpio 8 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET", |
| "CAM_STANDBY"; |
| qcom,gpio-set-tbl-num = <1 1>; |
| qcom,gpio-set-tbl-flags = <0 2>; |
| qcom,gpio-set-tbl-delay = <1000 4000>; |
| qcom,csi-lane-assign = <0xe4>; |
| qcom,csi-lane-mask = <0x3>; |
| qcom,sensor-position = <1>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <0>; |
| }; |
| |
| }; |