| /* |
| * Sonics Silicon Backplane |
| * Broadcom PCI-core driver |
| * |
| * Copyright 2005, Broadcom Corporation |
| * Copyright 2006, 2007, Michael Buesch <mb@bu3sch.de> |
| * |
| * Licensed under the GNU/GPL. See COPYING for details. |
| */ |
| |
| #include <linux/ssb/ssb.h> |
| #include <linux/pci.h> |
| #include <linux/delay.h> |
| #include <linux/ssb/ssb_embedded.h> |
| |
| #include "ssb_private.h" |
| |
| static u32 ssb_pcie_read(struct ssb_pcicore *pc, u32 address); |
| static void ssb_pcie_write(struct ssb_pcicore *pc, u32 address, u32 data); |
| static u16 ssb_pcie_mdio_read(struct ssb_pcicore *pc, u8 device, u8 address); |
| static void ssb_pcie_mdio_write(struct ssb_pcicore *pc, u8 device, |
| u8 address, u16 data); |
| |
| static inline |
| u32 pcicore_read32(struct ssb_pcicore *pc, u16 offset) |
| { |
| return ssb_read32(pc->dev, offset); |
| } |
| |
| static inline |
| void pcicore_write32(struct ssb_pcicore *pc, u16 offset, u32 value) |
| { |
| ssb_write32(pc->dev, offset, value); |
| } |
| |
| static inline |
| u16 pcicore_read16(struct ssb_pcicore *pc, u16 offset) |
| { |
| return ssb_read16(pc->dev, offset); |
| } |
| |
| static inline |
| void pcicore_write16(struct ssb_pcicore *pc, u16 offset, u16 value) |
| { |
| ssb_write16(pc->dev, offset, value); |
| } |
| |
| /************************************************** |
| * Code for hostmode operation. |
| **************************************************/ |
| |
| #ifdef CONFIG_SSB_PCICORE_HOSTMODE |
| |
| #include <asm/paccess.h> |
| /* Probe a 32bit value on the bus and catch bus exceptions. |
| * Returns nonzero on a bus exception. |
| * This is MIPS specific */ |
| #define mips_busprobe32(val, addr) get_dbe((val), ((u32 *)(addr))) |
| |
| /* Assume one-hot slot wiring */ |
| #define SSB_PCI_SLOT_MAX 16 |
| |
| /* Global lock is OK, as we won't have more than one extpci anyway. */ |
| static DEFINE_SPINLOCK(cfgspace_lock); |
| /* Core to access the external PCI config space. Can only have one. */ |
| static struct ssb_pcicore *extpci_core; |
| |
| |
| static u32 get_cfgspace_addr(struct ssb_pcicore *pc, |
| unsigned int bus, unsigned int dev, |
| unsigned int func, unsigned int off) |
| { |
| u32 addr = 0; |
| u32 tmp; |
| |
| /* We do only have one cardbus device behind the bridge. */ |
| if (pc->cardbusmode && (dev >= 1)) |
| goto out; |
| |
| if (bus == 0) { |
| /* Type 0 transaction */ |
| if (unlikely(dev >= SSB_PCI_SLOT_MAX)) |
| goto out; |
| /* Slide the window */ |
| tmp = SSB_PCICORE_SBTOPCI_CFG0; |
| tmp |= ((1 << (dev + 16)) & SSB_PCICORE_SBTOPCI1_MASK); |
| pcicore_write32(pc, SSB_PCICORE_SBTOPCI1, tmp); |
| /* Calculate the address */ |
| addr = SSB_PCI_CFG; |
| addr |= ((1 << (dev + 16)) & ~SSB_PCICORE_SBTOPCI1_MASK); |
| addr |= (func << 8); |
| addr |= (off & ~3); |
| } else { |
| /* Type 1 transaction */ |
| pcicore_write32(pc, SSB_PCICORE_SBTOPCI1, |
| SSB_PCICORE_SBTOPCI_CFG1); |
| /* Calculate the address */ |
| addr = SSB_PCI_CFG; |
| addr |= (bus << 16); |
| addr |= (dev << 11); |
| addr |= (func << 8); |
| addr |= (off & ~3); |
| } |
| out: |
| return addr; |
| } |
| |
| static int ssb_extpci_read_config(struct ssb_pcicore *pc, |
| unsigned int bus, unsigned int dev, |
| unsigned int func, unsigned int off, |
| void *buf, int len) |
| { |
| int err = -EINVAL; |
| u32 addr, val; |
| void __iomem *mmio; |
| |
| SSB_WARN_ON(!pc->hostmode); |
| if (unlikely(len != 1 && len != 2 && len != 4)) |
| goto out; |
| addr = get_cfgspace_addr(pc, bus, dev, func, off); |
| if (unlikely(!addr)) |
| goto out; |
| err = -ENOMEM; |
| mmio = ioremap_nocache(addr, len); |
| if (!mmio) |
| goto out; |
| |
| if (mips_busprobe32(val, mmio)) { |
| val = 0xffffffff; |
| goto unmap; |
| } |
| |
| val = readl(mmio); |
| val >>= (8 * (off & 3)); |
| |
| switch (len) { |
| case 1: |
| *((u8 *)buf) = (u8)val; |
| break; |
| case 2: |
| *((u16 *)buf) = (u16)val; |
| break; |
| case 4: |
| *((u32 *)buf) = (u32)val; |
| break; |
| } |
| err = 0; |
| unmap: |
| iounmap(mmio); |
| out: |
| return err; |
| } |
| |
| static int ssb_extpci_write_config(struct ssb_pcicore *pc, |
| unsigned int bus, unsigned int dev, |
| unsigned int func, unsigned int off, |
| const void *buf, int len) |
| { |
| int err = -EINVAL; |
| u32 addr, val = 0; |
| void __iomem *mmio; |
| |
| SSB_WARN_ON(!pc->hostmode); |
| if (unlikely(len != 1 && len != 2 && len != 4)) |
| goto out; |
| addr = get_cfgspace_addr(pc, bus, dev, func, off); |
| if (unlikely(!addr)) |
| goto out; |
| err = -ENOMEM; |
| mmio = ioremap_nocache(addr, len); |
| if (!mmio) |
| goto out; |
| |
| if (mips_busprobe32(val, mmio)) { |
| val = 0xffffffff; |
| goto unmap; |
| } |
| |
| switch (len) { |
| case 1: |
| val = readl(mmio); |
| val &= ~(0xFF << (8 * (off & 3))); |
| val |= *((const u8 *)buf) << (8 * (off & 3)); |
| break; |
| case 2: |
| val = readl(mmio); |
| val &= ~(0xFFFF << (8 * (off & 3))); |
| val |= *((const u16 *)buf) << (8 * (off & 3)); |
| break; |
| case 4: |
| val = *((const u32 *)buf); |
| break; |
| } |
| writel(val, mmio); |
| |
| err = 0; |
| unmap: |
| iounmap(mmio); |
| out: |
| return err; |
| } |
| |
| static int ssb_pcicore_read_config(struct pci_bus *bus, unsigned int devfn, |
| int reg, int size, u32 *val) |
| { |
| unsigned long flags; |
| int err; |
| |
| spin_lock_irqsave(&cfgspace_lock, flags); |
| err = ssb_extpci_read_config(extpci_core, bus->number, PCI_SLOT(devfn), |
| PCI_FUNC(devfn), reg, val, size); |
| spin_unlock_irqrestore(&cfgspace_lock, flags); |
| |
| return err ? PCIBIOS_DEVICE_NOT_FOUND : PCIBIOS_SUCCESSFUL; |
| } |
| |
| static int ssb_pcicore_write_config(struct pci_bus *bus, unsigned int devfn, |
| int reg, int size, u32 val) |
| { |
| unsigned long flags; |
| int err; |
| |
| spin_lock_irqsave(&cfgspace_lock, flags); |
| err = ssb_extpci_write_config(extpci_core, bus->number, PCI_SLOT(devfn), |
| PCI_FUNC(devfn), reg, &val, size); |
| spin_unlock_irqrestore(&cfgspace_lock, flags); |
| |
| return err ? PCIBIOS_DEVICE_NOT_FOUND : PCIBIOS_SUCCESSFUL; |
| } |
| |
| static struct pci_ops ssb_pcicore_pciops = { |
| .read = ssb_pcicore_read_config, |
| .write = ssb_pcicore_write_config, |
| }; |
| |
| static struct resource ssb_pcicore_mem_resource = { |
| .name = "SSB PCIcore external memory", |
| .start = SSB_PCI_DMA, |
| .end = SSB_PCI_DMA + SSB_PCI_DMA_SZ - 1, |
| .flags = IORESOURCE_MEM | IORESOURCE_PCI_FIXED, |
| }; |
| |
| static struct resource ssb_pcicore_io_resource = { |
| .name = "SSB PCIcore external I/O", |
| .start = 0x100, |
| .end = 0x7FF, |
| .flags = IORESOURCE_IO | IORESOURCE_PCI_FIXED, |
| }; |
| |
| static struct pci_controller ssb_pcicore_controller = { |
| .pci_ops = &ssb_pcicore_pciops, |
| .io_resource = &ssb_pcicore_io_resource, |
| .mem_resource = &ssb_pcicore_mem_resource, |
| }; |
| |
| /* This function is called when doing a pci_enable_device(). |
| * We must first check if the device is a device on the PCI-core bridge. */ |
| int ssb_pcicore_plat_dev_init(struct pci_dev *d) |
| { |
| if (d->bus->ops != &ssb_pcicore_pciops) { |
| /* This is not a device on the PCI-core bridge. */ |
| return -ENODEV; |
| } |
| |
| ssb_printk(KERN_INFO "PCI: Fixing up device %s\n", |
| pci_name(d)); |
| |
| /* Fix up interrupt lines */ |
| d->irq = ssb_mips_irq(extpci_core->dev) + 2; |
| pci_write_config_byte(d, PCI_INTERRUPT_LINE, d->irq); |
| |
| return 0; |
| } |
| |
| /* Early PCI fixup for a device on the PCI-core bridge. */ |
| static void ssb_pcicore_fixup_pcibridge(struct pci_dev *dev) |
| { |
| u8 lat; |
| |
| if (dev->bus->ops != &ssb_pcicore_pciops) { |
| /* This is not a device on the PCI-core bridge. */ |
| return; |
| } |
| if (dev->bus->number != 0 || PCI_SLOT(dev->devfn) != 0) |
| return; |
| |
| ssb_printk(KERN_INFO "PCI: Fixing up bridge %s\n", pci_name(dev)); |
| |
| /* Enable PCI bridge bus mastering and memory space */ |
| pci_set_master(dev); |
| if (pcibios_enable_device(dev, ~0) < 0) { |
| ssb_printk(KERN_ERR "PCI: SSB bridge enable failed\n"); |
| return; |
| } |
| |
| /* Enable PCI bridge BAR1 prefetch and burst */ |
| pci_write_config_dword(dev, SSB_BAR1_CONTROL, 3); |
| |
| /* Make sure our latency is high enough to handle the devices behind us */ |
| lat = 168; |
| ssb_printk(KERN_INFO "PCI: Fixing latency timer of device %s to %u\n", |
| pci_name(dev), lat); |
| pci_write_config_byte(dev, PCI_LATENCY_TIMER, lat); |
| } |
| DECLARE_PCI_FIXUP_EARLY(PCI_ANY_ID, PCI_ANY_ID, ssb_pcicore_fixup_pcibridge); |
| |
| /* PCI device IRQ mapping. */ |
| int ssb_pcicore_pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) |
| { |
| if (dev->bus->ops != &ssb_pcicore_pciops) { |
| /* This is not a device on the PCI-core bridge. */ |
| return -ENODEV; |
| } |
| return ssb_mips_irq(extpci_core->dev) + 2; |
| } |
| |
| static void ssb_pcicore_init_hostmode(struct ssb_pcicore *pc) |
| { |
| u32 val; |
| |
| if (WARN_ON(extpci_core)) |
| return; |
| extpci_core = pc; |
| |
| ssb_dprintk(KERN_INFO PFX "PCIcore in host mode found\n"); |
| /* Reset devices on the external PCI bus */ |
| val = SSB_PCICORE_CTL_RST_OE; |
| val |= SSB_PCICORE_CTL_CLK_OE; |
| pcicore_write32(pc, SSB_PCICORE_CTL, val); |
| val |= SSB_PCICORE_CTL_CLK; /* Clock on */ |
| pcicore_write32(pc, SSB_PCICORE_CTL, val); |
| udelay(150); /* Assertion time demanded by the PCI standard */ |
| val |= SSB_PCICORE_CTL_RST; /* Deassert RST# */ |
| pcicore_write32(pc, SSB_PCICORE_CTL, val); |
| val = SSB_PCICORE_ARBCTL_INTERN; |
| pcicore_write32(pc, SSB_PCICORE_ARBCTL, val); |
| udelay(1); /* Assertion time demanded by the PCI standard */ |
| |
| if (pc->dev->bus->has_cardbus_slot) { |
| ssb_dprintk(KERN_INFO PFX "CardBus slot detected\n"); |
| pc->cardbusmode = 1; |
| /* GPIO 1 resets the bridge */ |
| ssb_gpio_out(pc->dev->bus, 1, 1); |
| ssb_gpio_outen(pc->dev->bus, 1, 1); |
| pcicore_write16(pc, SSB_PCICORE_SPROM(0), |
| pcicore_read16(pc, SSB_PCICORE_SPROM(0)) |
| | 0x0400); |
| } |
| |
| /* 64MB I/O window */ |
| pcicore_write32(pc, SSB_PCICORE_SBTOPCI0, |
| SSB_PCICORE_SBTOPCI_IO); |
| /* 64MB config space */ |
| pcicore_write32(pc, SSB_PCICORE_SBTOPCI1, |
| SSB_PCICORE_SBTOPCI_CFG0); |
| /* 1GB memory window */ |
| pcicore_write32(pc, SSB_PCICORE_SBTOPCI2, |
| SSB_PCICORE_SBTOPCI_MEM | SSB_PCI_DMA); |
| |
| /* Enable PCI bridge BAR0 prefetch and burst */ |
| val = PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY; |
| ssb_extpci_write_config(pc, 0, 0, 0, PCI_COMMAND, &val, 2); |
| /* Clear error conditions */ |
| val = 0; |
| ssb_extpci_write_config(pc, 0, 0, 0, PCI_STATUS, &val, 2); |
| |
| /* Enable PCI interrupts */ |
| pcicore_write32(pc, SSB_PCICORE_IMASK, |
| SSB_PCICORE_IMASK_INTA); |
| |
| /* Ok, ready to run, register it to the system. |
| * The following needs change, if we want to port hostmode |
| * to non-MIPS platform. */ |
| ssb_pcicore_controller.io_map_base = (unsigned long)ioremap_nocache(SSB_PCI_MEM, 0x04000000); |
| set_io_port_base(ssb_pcicore_controller.io_map_base); |
| /* Give some time to the PCI controller to configure itself with the new |
| * values. Not waiting at this point causes crashes of the machine. */ |
| mdelay(10); |
| register_pci_controller(&ssb_pcicore_controller); |
| } |
| |
| static int pcicore_is_in_hostmode(struct ssb_pcicore *pc) |
| { |
| struct ssb_bus *bus = pc->dev->bus; |
| u16 chipid_top; |
| u32 tmp; |
| |
| chipid_top = (bus->chip_id & 0xFF00); |
| if (chipid_top != 0x4700 && |
| chipid_top != 0x5300) |
| return 0; |
| |
| if (bus->sprom.boardflags_lo & SSB_PCICORE_BFL_NOPCI) |
| return 0; |
| |
| /* The 200-pin BCM4712 package does not bond out PCI. Even when |
| * PCI is bonded out, some boards may leave the pins floating. */ |
| if (bus->chip_id == 0x4712) { |
| if (bus->chip_package == SSB_CHIPPACK_BCM4712S) |
| return 0; |
| if (bus->chip_package == SSB_CHIPPACK_BCM4712M) |
| return 0; |
| } |
| if (bus->chip_id == 0x5350) |
| return 0; |
| |
| return !mips_busprobe32(tmp, (bus->mmio + (pc->dev->core_index * SSB_CORE_SIZE))); |
| } |
| #endif /* CONFIG_SSB_PCICORE_HOSTMODE */ |
| |
| /************************************************** |
| * Workarounds. |
| **************************************************/ |
| |
| static void ssb_pcicore_fix_sprom_core_index(struct ssb_pcicore *pc) |
| { |
| u16 tmp = pcicore_read16(pc, SSB_PCICORE_SPROM(0)); |
| if (((tmp & 0xF000) >> 12) != pc->dev->core_index) { |
| tmp &= ~0xF000; |
| tmp |= (pc->dev->core_index << 12); |
| pcicore_write16(pc, SSB_PCICORE_SPROM(0), tmp); |
| } |
| } |
| |
| static u8 ssb_pcicore_polarity_workaround(struct ssb_pcicore *pc) |
| { |
| return (ssb_pcie_read(pc, 0x204) & 0x10) ? 0xC0 : 0x80; |
| } |
| |
| static void ssb_pcicore_serdes_workaround(struct ssb_pcicore *pc) |
| { |
| const u8 serdes_pll_device = 0x1D; |
| const u8 serdes_rx_device = 0x1F; |
| u16 tmp; |
| |
| ssb_pcie_mdio_write(pc, serdes_rx_device, 1 /* Control */, |
| ssb_pcicore_polarity_workaround(pc)); |
| tmp = ssb_pcie_mdio_read(pc, serdes_pll_device, 1 /* Control */); |
| if (tmp & 0x4000) |
| ssb_pcie_mdio_write(pc, serdes_pll_device, 1, tmp & ~0x4000); |
| } |
| |
| static void ssb_pcicore_pci_setup_workarounds(struct ssb_pcicore *pc) |
| { |
| struct ssb_device *pdev = pc->dev; |
| struct ssb_bus *bus = pdev->bus; |
| u32 tmp; |
| |
| tmp = pcicore_read32(pc, SSB_PCICORE_SBTOPCI2); |
| tmp |= SSB_PCICORE_SBTOPCI_PREF; |
| tmp |= SSB_PCICORE_SBTOPCI_BURST; |
| pcicore_write32(pc, SSB_PCICORE_SBTOPCI2, tmp); |
| |
| if (pdev->id.revision < 5) { |
| tmp = ssb_read32(pdev, SSB_IMCFGLO); |
| tmp &= ~SSB_IMCFGLO_SERTO; |
| tmp |= 2; |
| tmp &= ~SSB_IMCFGLO_REQTO; |
| tmp |= 3 << SSB_IMCFGLO_REQTO_SHIFT; |
| ssb_write32(pdev, SSB_IMCFGLO, tmp); |
| ssb_commit_settings(bus); |
| } else if (pdev->id.revision >= 11) { |
| tmp = pcicore_read32(pc, SSB_PCICORE_SBTOPCI2); |
| tmp |= SSB_PCICORE_SBTOPCI_MRM; |
| pcicore_write32(pc, SSB_PCICORE_SBTOPCI2, tmp); |
| } |
| } |
| |
| static void ssb_pcicore_pcie_setup_workarounds(struct ssb_pcicore *pc) |
| { |
| u32 tmp; |
| u8 rev = pc->dev->id.revision; |
| |
| if (rev == 0 || rev == 1) { |
| /* TLP Workaround register. */ |
| tmp = ssb_pcie_read(pc, 0x4); |
| tmp |= 0x8; |
| ssb_pcie_write(pc, 0x4, tmp); |
| } |
| if (rev == 1) { |
| /* DLLP Link Control register. */ |
| tmp = ssb_pcie_read(pc, 0x100); |
| tmp |= 0x40; |
| ssb_pcie_write(pc, 0x100, tmp); |
| } |
| |
| if (rev == 0) { |
| const u8 serdes_rx_device = 0x1F; |
| |
| ssb_pcie_mdio_write(pc, serdes_rx_device, |
| 2 /* Timer */, 0x8128); |
| ssb_pcie_mdio_write(pc, serdes_rx_device, |
| 6 /* CDR */, 0x0100); |
| ssb_pcie_mdio_write(pc, serdes_rx_device, |
| 7 /* CDR BW */, 0x1466); |
| } else if (rev == 3 || rev == 4 || rev == 5) { |
| /* TODO: DLLP Power Management Threshold */ |
| ssb_pcicore_serdes_workaround(pc); |
| /* TODO: ASPM */ |
| } else if (rev == 7) { |
| /* TODO: No PLL down */ |
| } |
| |
| if (rev >= 6) { |
| /* Miscellaneous Configuration Fixup */ |
| tmp = pcicore_read16(pc, SSB_PCICORE_SPROM(5)); |
| if (!(tmp & 0x8000)) |
| pcicore_write16(pc, SSB_PCICORE_SPROM(5), |
| tmp | 0x8000); |
| } |
| } |
| |
| /************************************************** |
| * Generic and Clientmode operation code. |
| **************************************************/ |
| |
| static void ssb_pcicore_init_clientmode(struct ssb_pcicore *pc) |
| { |
| struct ssb_device *pdev = pc->dev; |
| struct ssb_bus *bus = pdev->bus; |
| |
| if (bus->bustype == SSB_BUSTYPE_PCI) |
| ssb_pcicore_fix_sprom_core_index(pc); |
| |
| /* Disable PCI interrupts. */ |
| ssb_write32(pdev, SSB_INTVEC, 0); |
| |
| /* Additional PCIe always once-executed workarounds */ |
| if (pc->dev->id.coreid == SSB_DEV_PCIE) { |
| ssb_pcicore_serdes_workaround(pc); |
| /* TODO: ASPM */ |
| /* TODO: Clock Request Update */ |
| } |
| } |
| |
| void ssb_pcicore_init(struct ssb_pcicore *pc) |
| { |
| struct ssb_device *dev = pc->dev; |
| |
| if (!dev) |
| return; |
| if (!ssb_device_is_enabled(dev)) |
| ssb_device_enable(dev, 0); |
| |
| #ifdef CONFIG_SSB_PCICORE_HOSTMODE |
| pc->hostmode = pcicore_is_in_hostmode(pc); |
| if (pc->hostmode) |
| ssb_pcicore_init_hostmode(pc); |
| #endif /* CONFIG_SSB_PCICORE_HOSTMODE */ |
| if (!pc->hostmode) |
| ssb_pcicore_init_clientmode(pc); |
| } |
| |
| static u32 ssb_pcie_read(struct ssb_pcicore *pc, u32 address) |
| { |
| pcicore_write32(pc, 0x130, address); |
| return pcicore_read32(pc, 0x134); |
| } |
| |
| static void ssb_pcie_write(struct ssb_pcicore *pc, u32 address, u32 data) |
| { |
| pcicore_write32(pc, 0x130, address); |
| pcicore_write32(pc, 0x134, data); |
| } |
| |
| static void ssb_pcie_mdio_set_phy(struct ssb_pcicore *pc, u8 phy) |
| { |
| const u16 mdio_control = 0x128; |
| const u16 mdio_data = 0x12C; |
| u32 v; |
| int i; |
| |
| v = (1 << 30); /* Start of Transaction */ |
| v |= (1 << 28); /* Write Transaction */ |
| v |= (1 << 17); /* Turnaround */ |
| v |= (0x1F << 18); |
| v |= (phy << 4); |
| pcicore_write32(pc, mdio_data, v); |
| |
| udelay(10); |
| for (i = 0; i < 200; i++) { |
| v = pcicore_read32(pc, mdio_control); |
| if (v & 0x100 /* Trans complete */) |
| break; |
| msleep(1); |
| } |
| } |
| |
| static u16 ssb_pcie_mdio_read(struct ssb_pcicore *pc, u8 device, u8 address) |
| { |
| const u16 mdio_control = 0x128; |
| const u16 mdio_data = 0x12C; |
| int max_retries = 10; |
| u16 ret = 0; |
| u32 v; |
| int i; |
| |
| v = 0x80; /* Enable Preamble Sequence */ |
| v |= 0x2; /* MDIO Clock Divisor */ |
| pcicore_write32(pc, mdio_control, v); |
| |
| if (pc->dev->id.revision >= 10) { |
| max_retries = 200; |
| ssb_pcie_mdio_set_phy(pc, device); |
| } |
| |
| v = (1 << 30); /* Start of Transaction */ |
| v |= (1 << 29); /* Read Transaction */ |
| v |= (1 << 17); /* Turnaround */ |
| if (pc->dev->id.revision < 10) |
| v |= (u32)device << 22; |
| v |= (u32)address << 18; |
| pcicore_write32(pc, mdio_data, v); |
| /* Wait for the device to complete the transaction */ |
| udelay(10); |
| for (i = 0; i < max_retries; i++) { |
| v = pcicore_read32(pc, mdio_control); |
| if (v & 0x100 /* Trans complete */) { |
| udelay(10); |
| ret = pcicore_read32(pc, mdio_data); |
| break; |
| } |
| msleep(1); |
| } |
| pcicore_write32(pc, mdio_control, 0); |
| return ret; |
| } |
| |
| static void ssb_pcie_mdio_write(struct ssb_pcicore *pc, u8 device, |
| u8 address, u16 data) |
| { |
| const u16 mdio_control = 0x128; |
| const u16 mdio_data = 0x12C; |
| int max_retries = 10; |
| u32 v; |
| int i; |
| |
| v = 0x80; /* Enable Preamble Sequence */ |
| v |= 0x2; /* MDIO Clock Divisor */ |
| pcicore_write32(pc, mdio_control, v); |
| |
| if (pc->dev->id.revision >= 10) { |
| max_retries = 200; |
| ssb_pcie_mdio_set_phy(pc, device); |
| } |
| |
| v = (1 << 30); /* Start of Transaction */ |
| v |= (1 << 28); /* Write Transaction */ |
| v |= (1 << 17); /* Turnaround */ |
| if (pc->dev->id.revision < 10) |
| v |= (u32)device << 22; |
| v |= (u32)address << 18; |
| v |= data; |
| pcicore_write32(pc, mdio_data, v); |
| /* Wait for the device to complete the transaction */ |
| udelay(10); |
| for (i = 0; i < max_retries; i++) { |
| v = pcicore_read32(pc, mdio_control); |
| if (v & 0x100 /* Trans complete */) |
| break; |
| msleep(1); |
| } |
| pcicore_write32(pc, mdio_control, 0); |
| } |
| |
| int ssb_pcicore_dev_irqvecs_enable(struct ssb_pcicore *pc, |
| struct ssb_device *dev) |
| { |
| struct ssb_device *pdev = pc->dev; |
| struct ssb_bus *bus; |
| int err = 0; |
| u32 tmp; |
| |
| if (dev->bus->bustype != SSB_BUSTYPE_PCI) { |
| /* This SSB device is not on a PCI host-bus. So the IRQs are |
| * not routed through the PCI core. |
| * So we must not enable routing through the PCI core. */ |
| goto out; |
| } |
| |
| if (!pdev) |
| goto out; |
| bus = pdev->bus; |
| |
| might_sleep_if(pdev->id.coreid != SSB_DEV_PCI); |
| |
| /* Enable interrupts for this device. */ |
| if ((pdev->id.revision >= 6) || (pdev->id.coreid == SSB_DEV_PCIE)) { |
| u32 coremask; |
| |
| /* Calculate the "coremask" for the device. */ |
| coremask = (1 << dev->core_index); |
| |
| SSB_WARN_ON(bus->bustype != SSB_BUSTYPE_PCI); |
| err = pci_read_config_dword(bus->host_pci, SSB_PCI_IRQMASK, &tmp); |
| if (err) |
| goto out; |
| tmp |= coremask << 8; |
| err = pci_write_config_dword(bus->host_pci, SSB_PCI_IRQMASK, tmp); |
| if (err) |
| goto out; |
| } else { |
| u32 intvec; |
| |
| intvec = ssb_read32(pdev, SSB_INTVEC); |
| tmp = ssb_read32(dev, SSB_TPSFLAG); |
| tmp &= SSB_TPSFLAG_BPFLAG; |
| intvec |= (1 << tmp); |
| ssb_write32(pdev, SSB_INTVEC, intvec); |
| } |
| |
| /* Setup PCIcore operation. */ |
| if (pc->setup_done) |
| goto out; |
| if (pdev->id.coreid == SSB_DEV_PCI) { |
| ssb_pcicore_pci_setup_workarounds(pc); |
| } else { |
| WARN_ON(pdev->id.coreid != SSB_DEV_PCIE); |
| ssb_pcicore_pcie_setup_workarounds(pc); |
| } |
| pc->setup_done = 1; |
| out: |
| return err; |
| } |
| EXPORT_SYMBOL(ssb_pcicore_dev_irqvecs_enable); |