Bluetooth: Fix sending ReqSeq on I-frames
As specified by ERTM spec an ERTM channel can acknowledge received
I-frames(the data frames) by sending an I-frame with the proper ReqSeq
value (i.e. ReqSeq is set to BufferSeq). Until now we aren't setting the
ReqSeq value on I-frame control bits. That way we can save sending
S-frames(Supervise frames) only to acknowledge receipt of I-frames. It
is very helpful to the full-duplex channel.
ReqSeq is the packet sequence number sent in an acknowledgement frame to
acknowledge receipt of frames up to (ReqSeq - 1).
BufferSeq controls the receiver buffer, it is used to delay
acknowledgement of new frames to not cause buffer overflow. BufferSeq
value is not increased until frames are pulled by reassembly function.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
diff --git a/include/net/bluetooth/l2cap.h b/include/net/bluetooth/l2cap.h
index 9516f4b..327eb57 100644
--- a/include/net/bluetooth/l2cap.h
+++ b/include/net/bluetooth/l2cap.h
@@ -324,7 +324,6 @@
__u8 next_tx_seq;
__u8 expected_ack_seq;
- __u8 req_seq;
__u8 expected_tx_seq;
__u8 buffer_seq;
__u8 buffer_seq_srej;
diff --git a/net/bluetooth/l2cap.c b/net/bluetooth/l2cap.c
index 2d5d375..78ab881 100644
--- a/net/bluetooth/l2cap.c
+++ b/net/bluetooth/l2cap.c
@@ -1333,7 +1333,7 @@
tx_skb = skb_clone(skb, GFP_ATOMIC);
bt_cb(skb)->retries++;
control = get_unaligned_le16(tx_skb->data + L2CAP_HDR_SIZE);
- control |= (pi->req_seq << L2CAP_CTRL_REQSEQ_SHIFT)
+ control |= (pi->buffer_seq << L2CAP_CTRL_REQSEQ_SHIFT)
| (tx_seq << L2CAP_CTRL_TXSEQ_SHIFT);
put_unaligned_le16(control, tx_skb->data + L2CAP_HDR_SIZE);
@@ -1375,7 +1375,7 @@
bt_cb(skb)->retries++;
control = get_unaligned_le16(tx_skb->data + L2CAP_HDR_SIZE);
- control |= (pi->req_seq << L2CAP_CTRL_REQSEQ_SHIFT)
+ control |= (pi->buffer_seq << L2CAP_CTRL_REQSEQ_SHIFT)
| (pi->next_tx_seq << L2CAP_CTRL_TXSEQ_SHIFT);
put_unaligned_le16(control, tx_skb->data + L2CAP_HDR_SIZE);
@@ -3298,12 +3298,16 @@
{
struct l2cap_pinfo *pi = l2cap_pi(sk);
u8 tx_seq = __get_txseq(rx_control);
+ u8 req_seq = __get_reqseq(rx_control);
u16 tx_control = 0;
u8 sar = rx_control >> L2CAP_CTRL_SAR_SHIFT;
int err = 0;
BT_DBG("sk %p rx_control 0x%4.4x len %d", sk, rx_control, skb->len);
+ pi->expected_ack_seq = req_seq;
+ l2cap_drop_acked_frames(sk);
+
if (tx_seq == pi->expected_tx_seq)
goto expected;