[SCSI] lpfc 8.3.4: Consistently Implement persistent port disable
Consistently implement persistent port disable.
Ability was to be managed in the adapter via firmware via flash settings.
However, not all firmware images supported it. Uniformly support it
everywhere.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c
index f8271a5..900b562 100644
--- a/drivers/scsi/lpfc/lpfc_init.c
+++ b/drivers/scsi/lpfc/lpfc_init.c
@@ -211,7 +211,7 @@
goto out_free_mbox;
do {
- lpfc_dump_mem(phba, pmb, offset);
+ lpfc_dump_mem(phba, pmb, offset, DMP_REGION_VPD);
rc = lpfc_sli_issue_mbox(phba, pmb, MBX_POLL);
if (rc != MBX_SUCCESS) {
@@ -425,6 +425,9 @@
return -EIO;
}
+ /* Check if the port is disabled */
+ lpfc_sli_read_link_ste(phba);
+
/* Reset the DFT_HBA_Q_DEPTH to the max xri */
if (phba->cfg_hba_queue_depth > (mb->un.varRdConfig.max_xri+1))
phba->cfg_hba_queue_depth =
@@ -524,27 +527,49 @@
/* Set up error attention (ERATT) polling timer */
mod_timer(&phba->eratt_poll, jiffies + HZ * LPFC_ERATT_POLL_INTERVAL);
- lpfc_init_link(phba, pmb, phba->cfg_topology, phba->cfg_link_speed);
- pmb->mbox_cmpl = lpfc_sli_def_mbox_cmpl;
- lpfc_set_loopback_flag(phba);
- rc = lpfc_sli_issue_mbox(phba, pmb, MBX_NOWAIT);
- if (rc != MBX_SUCCESS) {
- lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
+ /* Check if the port is disabled */
+ lpfc_sli_read_serdes_param(phba);
+
+ if (phba->hba_flag & LINK_DISABLED) {
+ lpfc_printf_log(phba,
+ KERN_ERR, LOG_INIT,
+ "2598 Adapter Link is disabled.\n");
+ lpfc_down_link(phba, pmb);
+ pmb->mbox_cmpl = lpfc_sli_def_mbox_cmpl;
+ rc = lpfc_sli_issue_mbox(phba, pmb, MBX_NOWAIT);
+ if ((rc != MBX_SUCCESS) && (rc != MBX_BUSY)) {
+ lpfc_printf_log(phba,
+ KERN_ERR, LOG_INIT,
+ "2599 Adapter failed to issue DOWN_LINK"
+ " mbox command rc 0x%x\n", rc);
+
+ mempool_free(pmb, phba->mbox_mem_pool);
+ return -EIO;
+ }
+ } else {
+ lpfc_init_link(phba, pmb, phba->cfg_topology,
+ phba->cfg_link_speed);
+ pmb->mbox_cmpl = lpfc_sli_def_mbox_cmpl;
+ lpfc_set_loopback_flag(phba);
+ rc = lpfc_sli_issue_mbox(phba, pmb, MBX_NOWAIT);
+ if (rc != MBX_SUCCESS) {
+ lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
"0454 Adapter failed to init, mbxCmd x%x "
"INIT_LINK, mbxStatus x%x\n",
mb->mbxCommand, mb->mbxStatus);
- /* Clear all interrupt enable conditions */
- writel(0, phba->HCregaddr);
- readl(phba->HCregaddr); /* flush */
- /* Clear all pending interrupts */
- writel(0xffffffff, phba->HAregaddr);
- readl(phba->HAregaddr); /* flush */
+ /* Clear all interrupt enable conditions */
+ writel(0, phba->HCregaddr);
+ readl(phba->HCregaddr); /* flush */
+ /* Clear all pending interrupts */
+ writel(0xffffffff, phba->HAregaddr);
+ readl(phba->HAregaddr); /* flush */
- phba->link_state = LPFC_HBA_ERROR;
- if (rc != MBX_BUSY)
- mempool_free(pmb, phba->mbox_mem_pool);
- return -EIO;
+ phba->link_state = LPFC_HBA_ERROR;
+ if (rc != MBX_BUSY)
+ mempool_free(pmb, phba->mbox_mem_pool);
+ return -EIO;
+ }
}
/* MBOX buffer will be freed in mbox compl */
pmb = mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);